Advertisement
Advertisement
INSTRUCTION MANUAL
Requires : 4-channel radio w/ 4 micro servos,
Outrunner Motor w/ Propeller Adaptor
20A Brushless ESC, 3 cells 11.1V
2100mAh Li - Po battery & charger.
Wing Span
Wing Area
Flying Weight
Fuselage Length
Specifications
40.5 in / 1030 mm
288 sq in / 18.6 sq dm
26.5 oz / 750 g
34.5 in / 880 mm
*Specifications are subject to change without notice.*
Warning! This model is not a toy.
It is designed for maximum performance. Please seek advice if one is not familiar with this kind of electric powered precision model. Operating this model without prior preparation may cause injuries. Remember, safety is the most important thing. Always keep this instruction manual at hand for quick reference.
The World Models
Manufacturing Co., LTD.
www.theworldmodels.com
E252XMPO26401107
FACTORY PRE-FABRICATED
ALMOST-READY-TO-FLY (ARF) SERIES
MADE IN CHINA
INDEX
BEFORE YOU BEGIN
PARTS LIST
ASSEMBLY
SAFETY PRECAUTIONS
BEFORE YOU BEGIN
P.1
P.2
P.3-P.10
P.10
1
Read through the manual before you begin, so you will have an overall idea of what to do.
2
Check all parts. If you find any defective or missing parts contact your local dealer. Please
DRY FIT and check for defects for all parts that will require CA or Epoxy for final assembly.
Any parts you find to be defective after the gluing process may be difficult to remove for warranty replacement. The manufacturer will replace any defective parts, but will not extend to the parts that are good before gluing to defective parts during assembly. Warranty will not cover any parts modified by customer.
3
Symbols used throughout this instruction manual comprise of the following :-
Apply epoxy glue.
Apply instant glue
(C.A.glue, super glue.)
Must be purchased separately !
Apply thread locker
Assemble left and right sides the same way.
Peel off shaded portion covering film.
3mm
Drill holes with the specified diameter (here: 3mm).
Pay close attention here!
E252XMPO26401107
P.1
Ensure smooth non-binding movement while assembling.
Cut off shaded portion.
Pierce the shaded portion covering film.
Warning!
Do not overlook this symbol !
Parts List
1. MAIN WING -- 1 pair
2. SCREW PB2x14mm -- 4 pcs
SCREW PA1.7x8mm -- 8 pcs
STRAPER PL4112106 -- 2 pcs
FUEL TUBE d2xD4x4mm -- 4 pcs
CLEVIS PL4112105 -- 2 pcs
HORN PL4112102 -- 2 sets
PUSHROD Ø1.4x71mm w/ Threads (For Aileron) -- 2 pcs
SERVO MOUNTING PANEL PL5310020 -- 1 pair
3. STABILIZER & ELEVATOR -- 1 set
FUSELAGE -- 1 pc.
4. VERTICAL FIN & RUDDER -- 1 set
5. TAIL LANDING GEAR PL3410030 -- 1 set
TAIL WHEEL PL3410030 Ø23mm -- 1 pc.
PLASTIC COLLAR d1xD5x2mm -- 2 pcs
SCREW PA2x8mm -- 2 pcs
SCREW PM2x8mm -- 1 pc.
M2 NUT -- 1 pc.
ALUMINUM PLATE 0.3mm -- 1 pc.
6. SCREW PB2x10mm -- 4 pcs
CLEVIS PL4112105 -- 2 pcs
FUEL TUBE d2xD4x4mm -- 2 pcs
HORN PL4112102 -- 2 sets
PUSHROD Ø1.4x375mm w/ Threads (For Elevator) -- 2 pcs
7. SCREW PB2x10mm -- 2 pcs
CLEVIS PL4112105 -- 1 pc.
FUEL TUBE d2xD4x4mm -- 1 pc.
HORN PL4112102 -- 1 set
PUSHROD Ø1.4x445mm w/ Threads (For Rudder) -- 1 pc.
8. FOLDING PROPELLER SET (10x5) PL6314040 -- 1 set
SCREW PM2x12mm -- 2 pcs
SPINNER Ø45mm SP27045WHO -- 1 pc.
SCREW PM3x6mm -- 4 pcs
WASHER d3xD7mm -- 4 pcs
COWLING -- 1 pc.
SCREW PWA2x8mm -- 4 pcs
E252XMPO26401107
P.2
9. MAIN LANDING GEAR -- 1 set
MAIN WHEEL Ø40mm -- 2 pcs
WHEEL PANTS -- 1 pair
SCREW PA2.6x10mm -- 3 pcs
SCREW PM3x25mm -- 2 pcs
WASHER d3xD7mm -- 4 pcs
M3 NUT -- 2 pcs
COLLAR Ø3.1mm w/ Set Screw -- 2 sets
COPPER TUBE d3.1xD4x5mm -- 2 pcs
ALUMINUM PLATE 0.5mm -- 2 pcs
SCREW PWA2x6mm -- 4 pcs
10. EYE SCREW PA2.5x10x23mm -- 2 pcs
WING TUBE d9.6x240mm -- 1 pc.
RUBBER BAND D1x30mm -- 2 pcs
11. STRAPER PL4112106 -- 2 pcs
FUEL TUBE d2xD4x4mm -- 2 pcs
BATTERY TIE 200mm -- 1 pc.
SPONGE 10x50x150mm -- 2 pcs
DOUBLE-SIDED TAPE 30x35mm -- 1 pc.
PUSHROD Ø1.4x52mm (For Elevator) -- 1 pc.
PUSHROD CONNECTOR PL4410020 -- 1 set
12. CANOPY -- 1 pc.
SCREW PM2x12mm -- 1 pc.
WASHER d2xD5mm -- 1 pc.
M2 NYLON INSERT LOCK NUT -- 1 pc.
MOUNTING PLATE 5x15mm PL4114050 -- 1 pc.
PILOT PC001050B -- 1 pc.
13. DECALS:E252XMDEC -- 1 set
COVERING:
LIGHTEX SGX252000
LIGHTEX SGX100 WHITE
LIGHTEX SGX540 PEARL GREEN
TOUGHLON STL412G CHECKER FERRARI RED/ GOLD
1
Main Wing
Apply instant type CA glue to both sides of each hinge.
Aileron Servo Lead
Bottom View
2
Aileron Servo
PB2x14mm
Screw
4
PA1.7x8mm
Screw
8
Ø1mm pilot holes for World
Models tri-horn are pre-drilled.
Please look for pin-hole marks at under side of control surfaces.
TWM PL8210010
CLEVIS WRENCH
Straper
Fuel Tube d2xD4x4mm
PA1.7x8mm
02L
03L
04L
02R
03R
04R
Bottom View
PB2x14mm
Fuel Tube d2xD4x4mm
2mm
Horn
Clevis
Pushrod
Ø1.4x71mm
Please choose either 02L & 02R or 03L & 03R or 04L & 04R that suits your servo.
E252XMPO26401107
3 Stabilizer & Elevator
B
(Stabilizer)
B
(Main Wing)
B=B
Temporary install the main wing, adjust leveling of the stabilizer to make it as parallel to the main wing as possible.
*Also refer to step 13 Wing Setting
A
A=A
A
Apply instant type CA glue to both sides of each hinge.
4 Vertical Fin & Rudder
1
3
Completed
E252XMPO26401107
2
C C
P.4
C=C
Apply instant type CA glue to both sides of each hinge.
5 Tail Landing Gear
PA2x8mm
Screw
PM2x8mm
Screw
1
M2
Nut
2
1
1.5mm
PA2x8mm
1.5mm
M2
Nut
Plastic Collar
Bottom View
PM2x8mm
6
Elevator Pushrod
PB2x10mm
Screw
4
TWM PL8210010
CLEVIS WRENCH
Fuel Tube
Clevis
PB2x10mm
Horn
Pushrod
Ø1.4x375mm
2mm
Ø1mm pilot holes for World Models horn are pre-drilled.
Please look for pin-hole marks at under side of control surfaces.
40mm
125mm
Bottom View
7
Rudder Pushrod
PB2x10mm
Screw
2
Ø1mm pilot holes for World Models horn are pre-drilled.
Please look for pin-hole marks at under side of control surfaces.
Horn
TWM PL8210010
CLEVIS WRENCH
2mm
Clevis
Pushrod
Ø1.4x445mm
60mm
20mm
PB2x10mm
Fuel Tube d2xD4x4mm
Bottom View
E252XMPO26401107
P.5
8 Outrunner Motor / Cowling
PM3x6mm
Screw
4
PM2x12mm
Screw
2 d3xD7mm
Washer
4
PWA2x8mm
Screw
4
PA2.6x8mm
Screw
2
1
PM3 screws, too much could split the firewall.
2
Outrunner Motor 28/ 30
KM0283010
Optional Parts
Solder
Propeller Adaptor
(d3xD5) HW2340100
motor casing is not in anything.
TWM
KP0011310
Solder
3
PM2x12mm
PM3x6mm d3xD7mm
Washer
4
Double-Sided tape
5
TWM HW3111400
PROPELLER ADAPTOR WRENCH
Brushless ESC
Ø40mm Spinner
PM2x12mm
Don’t over-tighten the PM2 screws, themselves when spinning.
9
Main Landing Gear
PA2.6x10mm
Screw
3
PM3x25mm
Screw
2
M3
Nut
2
4 d3xD7mm
Washer
4
3.1mm
Collar
2 d3.1xD4x5mm
Copper Tube
2
PA2.6x10mm
E252XMPO26401107
Bottom View
P.6
M5 Nut
1.5mm
PWA2x8mm
PA2.6x8mm
PM3x25mm
Wheel d3xD7mm Washer
Plate 0.5mm
M3 Nut
PWA2x6mm
1mm
Completed
10 Main Wing
Up Bottom
90
1.5mm
Eye Screw
PA2.5x10x23mm
Bottom View
Wing Tube
D9.6x240mm
Rubber Band
E252XMPO26401107
P.7
Aileron Servo Lead
11 Radio Equipment Install and arrange the servo as shown in the diagram.
Straper
Elevator Servo
Battery Tie
Front
Elevator Servo
Pushrod Connector
Elevator Pushrod
Ø1.4x52mm
KA1.7x6mm
J1(Pushrod Ø1.4x52mm)
J1
J2(Pushrod Ø1.4x375mm)
J2
Receiver
Rudder Servo
Sponge
Battery
12
Canopy
PM2x8mm
Screw
1 d2xD5mm
Washer
1
M2
Nylon Insert Lock Nut
1
Pilot d2xD5mm
Washer
PM2x8mm
2mm
Mounting Plate
Completed
E252XMPO26401107
P.8
13 Wing Setting
Adjust the wing and fuselage configuration as shown in the diagrams.
A A'
C
B
C'
E252XMPO26401107
A=A' B=B'
P.9
C=C'
14 Control Throws
15
Rudder
C.G.
Elevator
30mm
30mm
Adjust the control throws as shown in the diagram.
These throws are good for general flying. You can adjust according to your personal preference.
20mm
20mm
Aileron
10mm
10mm
The ideal C.G. position is 63.5mm (2.5 in.) behind the leading edge measured at where the wing meets the fuselage. In order to obtain the C.G. specified, add weight to the fuselage or move the battery position. Check the C.G. before flying.
63.5mm
2.5 in
C.G.
http://www.theworldmodels.com/para/instruction/instructionManuals.php
Warning!
Important Safety Precautions
# First time flyer should never fly by himself / herself. Assistance from experienced flyer is absolutely necessary.
# Pre-flight adjustment must be done before flying, it is very dangerous to fly a badly pre-adjusted aircraft.
# is specially designed to be powered by
KM0283010 Outrunner Motor
.
# Make sure the air field is spacious, never fly the plane too close to people and never get too close to a running
propeller. Extreme caution should be exercised when working with electric powered models. Make sure the
propeller is cleared of all objects, especially your hands before connecting the battery to the model. Make sure
you understand the operation of the ESC (Electronic Speed Control) by studying the ESC manual. Once you
plug in the battery for electric powered model, always treat the propeller as a rotating one, as accidental
movement of the throttle stick will spin the propeller and could cause injuries.
# If you find wrinkles on the covering as a result of weather changes, you can use hot iron to remove the wrinkles.
Please begin with lower temperature setting and gradually raise the temperature until the wrinkles are gone.
Too hot an iron may damage the covering. Don't use hot iron near the seams or edges, hot iron will melt the
glue and shrink the covering at the same time, causing the seams to pull away.
# Check and re-tighten up all factory assembled screws, use thread locker if necessary.
E252XMPO26401107
P.10
LINKAGE CONNECTOR
HW7111050 & HW7111060
Drill 2mm hole at servo horn.
Insert linkage connector into servo horn.
Make sure shoulder of screw is cleared from servo horn.
Add washer to reduce play if necessary.
Shoulder
Tighten up the round nut against the shoulder. Apply
CA or permanent thread locker.
After fastening the round nut, make sure that the linkage connector can rotate freely.
E252XMPO26401107
Product Registration Form (US Customers)
We would like to share with you any relevant information regarding your model, including product news and free upgrade parts when applicable. Please fill in the following and send to
AirBorne Models, 4749-K, Bennett Drive, Livermore, CA 94551 USA.
1. Name:______________________________________________
2. Address:____________________________________________
3. Phone #:____________________ E-mail:__________________
4. Model:______________________________________________
Wing QC#__________ Fuselage QC# _______________________
(QC numbers are stamped on wing and fuselage)
5. Date of Purchase:_____________________________________
6. Store Name: _________________________________________
Please call AirBorne Models at 925 371 0922 for any assistance in filling this form.
Thank you very much for purchasing our product.
E252XMPO26401107
E252XMPO26401107
Pl8210010
E252XMPO26401107
E252XMPO26401107
The World Models
Manufacturing Co., LTD.
www.theworldmodels.com

Public link updated
The public link to your chat has been updated.
Advertisement