advertisement
SENTROL ZX400
/ZX410
Security System Control
Programming
1
2
TABLE OF CONTENTS
Table of Contents
Operating the System .............................................................................................. 5
Introduction ............................................................................................................. 5
Powering Up With the Control Station ...................................................................... 5
Control Stations ........................................................................................................ 6
Control Station Overview ..........................................................................................7
Control Station Function Keys ...................................................................................8
Secondary Function Keys ..........................................................................................8
Installer Arming and Disarming .................................................................................9
Installer On Premises ................................................................................................. 9
Trouble Conditions ................................................................................................... 9
Testing ......................................................................................................................9
Programming the Control ..................................................................................... 10
Introduction ........................................................................................................... 10
Local Programming................................................................................................. 10
Remote Programming (RPM/2) ...............................................................................10
Area Partitioning ..................................................................................................... 10
LED Control Station Programming ..........................................................................12
Installer Level Programming .................................................................................. 13
Menu Options......................................................................................................... 13
Remote Connect ...........................................................................................13
Set Clock ....................................................................................................... 13
Edit Function Map .........................................................................................14
Entering a New Value At a Location ............................................................... 14
Programming Account Code and Telephone Number Digits ......................... 15
Programming Report Codes and Attribute Fields ...........................................15
Additional Programming Notes ..................................................................... 15
Programming Zone Names ...........................................................................15
Programming User Codes .............................................................................16
Restore Factory Defaults ................................................................................17
Days Until Next Comm Test ..........................................................................17
Call RPM ....................................................................................................... 17
Program RF Data ...........................................................................................18
Programming RF Zone Devices Into the RF Gateway .......................... 18
Programming RF User Devices Into the RF Gateway ............................ 19
Programming RF Devices Into the Control Panel ................................. 19
3
TABLE OF CONTENTS
Function Map ......................................................................................................... 20
Area Data Descriptions ..................................................................................20
Keypad Data Descriptions .............................................................................23
Zone Data Descriptions .................................................................................25
User Data Description ...................................................................................28
Authority Levels ............................................................................................. 29
Output Definitions Description ...................................................................... 31
Bell Output Activation .........................................................................33
Programmable Output Activation ....................................................... 33
Global System Options Description ............................................................... 35
Communicator Data Description ................................................................... 37
Communication Numbers Description .......................................................... 38
Dialed Digits Allowed ..........................................................................39
Pager Telephone Numbers .................................................................. 39
Event Reporting Description ..........................................................................40
Zone Report Codes Description ..................................................................... 42
User Report Codes Description ...................................................................... 44
System Report Codes Description .................................................................. 45
Area Schedules Description ...........................................................................47
Automatic Arming ..............................................................................47
Latch Key Schedules ...........................................................................47
Programming Options ...................................................................................49
Programming Notes ............................................................................................... 50
Digital Communicator Table For Contact ID Formats ........................................... 56
UL Programming Requirements ............................................................................ 59
Underwriters Laboratories (UL) Listing .................................................................... 59
UL Notes In This Manual .........................................................................................59
UL Notes About Program Functions ........................................................................ 59
UL Notes About Zone Planning ...............................................................................60
4
OPERATING THE SYSTEM
Operating the System
Introduction
The Sentrol ZX400/ZX410 Security System incorporates the most desired operational features available today. The ZX400/ZX410 features ease of installation and programming with an easy-to-operate keypad.
Features such as cross-zoning, delay before dialing, and an audibles “mute” function on the keypad help reduce false alarms.
The ZX400/ZX410 is pre-programmed at the factory with one 2-wire smoke detector zone and twelve burglar zones (one delay, two interior, and nine instant) through Sentrol’s unique “2 in 1” Zoning™.
A Zone Expander Module (ZXEXP) may be added to provide an additional 2-wire smoke detector zone and up to 16 additional zones. Up to 16 RF Points may be used with the 4710 and 4720 RF Gateways.
The ZX400/ZX410 Security Control is easily programmed with any one of four Control Stations (LCD,
LED, SSD, or VFD). The Control’s on-board RAM maintains its data even with the power disconnected. The
Control may also be programmed remotely with the aid of a personal computer (PC) and a modem using
Sentrol’s remote programming software (RPM2PRO) and a panel support module (PRO400).
The ZX400/ZX410 Security Control allows the division of a single system into two distinct areas, with an optional common area. To the customer, each area appears to be a fully functional system. The common area appears to be an extension of both areas. Each zone must be assigned to one of the two areas or to the common area. Each Control Station must be assigned to one of the two areas and may be extended to operate in the other area as a secondary area. The common area is accessible to all Control Stations.
The Control may have up to 50 user codes. Each user passcode must be assigned to one or both of the areas, and it must also be programmed with one of the
15 different levels of authority.
NOTE
Common Area is available in Rev 2.11
software and later revisions. Check software version label or control panel to determine revision level of software.
5
Powering Up With The Control
Station
The control comes from the manufacturer with a factory set (default) program. The factory default code for user passcode No. 1 is “1234”. This passcode is authorized to perform all user level functions. The default setting for the installer passcode is “9632”. The installer passcode can perform the installer level functions. (See Installer Level Programming - User Data
Description for the listed functions). All zones and Control Stations are assigned to Area 1 at default. The default setting for user passcode No. 50 is “1245” and it is authorized to perform all user level functions. It is assigned to both Area 1 and 2.
When a Control Station is powered-up, it briefly displays a test pattern followed by its data bus address.
The Control Station will then begin displaying information from the control panel. During the first fifteen seconds after power-up, the control panel will instruct the Control Station to display the panel’s software revision and flash the AWAY, STAY, NIGHT, READY, and
TROUBLE LEDs.
READY
TROUBLE
PANEL REV 2.10
NOTE
Rev number may change as software is upgraded.
OPERATING THE SYSTEM
Once the zones are in a secure state, the Control
Station displays:
READY
TROUBLE
A1 READY TO ARM
JAN 21 05:27:52
Nearly every option on the control requires the use of a valid user passcode. The user passcode may be used for functions in a specific area or system-wide.
Most of the options may be performed at any time, even while the control is fully or partially armed. To perform a function, a user must press the key corresponding to that function and then enter a passcode with the appropriate authority level. For purposes of discussion, the installer and the end user are both considered system users, but have different levels of authorization.
Control Stations
AWAY
STAY
NIGHT
READY
TROUBLE
FIRE
1
9
5
2
6
10
3
7
11
4
8
12
VIEW INFO ALM MEM EVENT LOG
1
BYPASS
4
RST SMOKE
7
QUIT
CLEAR
HOME
2
DELAY ARM
5
TEST
3
CHIME
6
PROGRAM
8
ACCESS
9
INSTANT
0
ENTER
NEXT
A B C
PREV
LED Control Station
(ZXLED12)
AWAY
STAY
NIGHT
READY
TROUBLE
VIEW INFO ALM MEM EVENT LOG
1
BYPASS
4
RST SMOKE
7
QUIT
CLEAR
HOME
2
DELAY ARM
5
TEST
3
CHIME
6
PROGRAM
8
ACCESS
9
INSTANT
0
ENTER
NEXT
SSD Control Station
(ZXSSD)
D
CANCEL
AWAY
STAY
NIGHT
VIEW INFO
1
BYPASS
4
RST SMOKE
7
QUIT
CLEAR
HOME
ALM MEM
2
DELAY ARM
EVENT LOG
3
CHIME
5
TEST
8
ACCESS
6
PROGRAM
9
INSTANT
0
ENTER
NEXT
LCD Control Station
(ZXLCD)
AWAY
STAY
NIGHT
VIEW INFO
1
BYPASS
4
RST SMOKE
7
QUIT
CLEAR
HOME
ALM MEM
2
DELAY ARM
EVENT LOG
3
CHIME
5
TEST
8
ACCESS
6
PROGRAM
9
INSTANT
0
ENTER
NEXT
VFD Control Station
(ZXVFD)
FIGURE 1 System Control Stations
6
OPERATING THE SYSTEM
Control Station Overview
For SSD, LED, LCD, and VFD Control Stations:
Away, Stay, and Night Keys
These keys, followed by a passcode, arm one or both areas to the
AWAY, STAY, or NIGHT level.
Away, Stay, and Night LED’s
These LEDs backlight the AWAY, STAY, and NIGHT keys to indicate the armed level of the Control Station’s primary area. These will flash during Exit Time or during a Burglar Alarm after Dialer Delay has expired.
Off/Cancel Key
This key, followed by a valid user code, disarms an area(s), silences and cancels alarms, and silences trouble conditions.
Instant/Enter Key
This key is used in programming to store entered data. Also, when pressed during an exit time from a STAY or NIGHT arming, this key disables both the entry and exit times for the primary area of the
Control Station.
Keypad Audibles
The piezo resonator activates for conditions including entry and exit notification, alarm, trouble, chime, etc.
Auxiliary Keys
When enabled, these keys activate the auxiliary alarms (Fire, Police,
Medical Emergency) or call a pager.
Clear/Quit Key
This key is used to reset any entry error and to allow you to escape out of an operation. To clear a “Missing Keypad”, “Memory Error”, or
“Smoke Trouble” system trouble condition or to turn off the Duress output, press and hold the CLEAR key for three seconds.
Keyboard Backlighting
The Control Station contains recessed LEDs to provide a light in dark or dimly lit environments.
For SSD and LED Control Stations only:
Ready LED
This LED indicates the status of the Burglar zones assigned to the Control Station’s primary area. It illuminates when the Burglar zones are all secure.
Trouble LED
This LED will illuminate for system troubles (AC failure, low battery, communication failure), zone troubles, and Burglar Tamper conditions.
(See Operating the System - Trouble Conditions for a complete list of trouble conditions).
For LED Control Stations only:
Zone Status LED’s
These LEDs generally indicate the condition of zones 1 through 12.
See the ZXLED8/ZXLED12 User Guide for how the LEDs indicate the
Normal, Faulted, Bypassed, Trouble, and Alarm conditions.
These LEDs may also display system trouble conditions and programming information.
Fire Zone LED
This LED indicates the status of the two-wire smoke zone on the main control board (Zone 30).
For SSD Control Stations only:
Seven Segment Display
The three Seven Segment Display (SSD) characters enunciate system status, zone status and user information. See the ZXSSD User Guide for details.
7
OPERATING THE SYSTEM
Control Station Function Keys
All Control Station function keys (except the View
Info Key) require that the function key be pressed followed by a valid passcode. The passcode’s authority level will determine if the selected function can be performed. While entering the passcode, there will be a four second time-out for no activity.
After the passcode has been entered, there will be a three minute time-out for no activity. The time-out will return the Control Station to idle. The operator may press the CLEAR key at any time to return the
Control Station to idle.
Below are the functions associated with keys 0 - 9 and a brief description of the functions. For details on the operation of these functions, as well as on the three arming keys, see the appropriate User
Guide.
1
2
3
4
5
6
7
VIEW INFO KEY
This key is used to view information and scroll through alarm and trouble conditions. A passcode is not required to perform this function.
ALM MEM KEY
This key allows you to view the most recent alarm event(s) on the Control Station.
EVENT LOG KEY
From an LED or SSD Control Station, this key will initiate printing of the Event Log.
From an LCD or VFD Control Station, this key will allow you to view the Event Log on the Control Station or initiate printing the log.
BYPASS KEY
This key allows you to select zones to be bypassed (removed from the system) and unbypassed (restored to the system).
DELAY ARM KEY
This key extends or postpones an automatic arming by one hour.
CHIME KEY
This key turns the chime function on or off for a particular area.
RST SMOKE KEY
This key resets all latched smoked detectors and clears “Smoke Troubles” and
”Bell Silenced”.
8
9
0
Secondary Function Keys
The Control Station secondary function keys may be activated by pressing the ENTER key followed by
Key #1 through Key #6. A passcode is not required to activate these functions. These functions are activated by pressing the following:
ENTER
+
1
Turns Lamp Trigger Output
ON or OFF
ENTER
+
2
Turns Universal Output ON or
OFF
ENTER
+
3
Quick Access from Keypad
ENTER
+
ENTER +
ENTER
+
TEST KEY
This key allows you to perform one of the six following tests: Walk, Battery, Bell,
Communications, Keypad, and RF Signal
Strength. After a valid passcode is entered, you may select the test to perform.
PROGRAM KEY
This key is used to enter installer or user level programming. User level programming is described in the appropriate User
Guide. Installer level programming is described in Installer Level Programming.
ACCESS KEY
This key is used to activate a door strike or other similar function.
4
5
6
Turns Key 4 Output ON or OFF
Turns Key 5 Output ON or OFF
Turns Key 6 Output ON or OFF
8
Please see Installer Level Programming - Output Definitions Description for more details on the operation of these functions. The above outputs are only available to the user if you program them as Programmable
Outputs. If any of these features are made available to the user, please instruct the user on their operation as it is not detailed in the appropriate User Guide.
OPERATING THE SYSTEM
Installer Arming and Disarming
The installer passcode may be used to arm one or both areas. It may be used to disarm one or both areas, but only if the area was armed by the installer passcode. It may be used to silence alarms and to silence trouble conditions. When it is used to silence a Burglar alarm, it will not disarm the area or cancel the alarm unless the area was armed by the installer passcode. For a detailed description of arming and disarming procedures, see the appropriate
User Guide.
Installer On Premises
When the installer passcode is used to program Function Map data or User Codes on the control panel or
RF Data on an RF Gateway, a “Local Program Begin” event is logged to be reported. A “Local Program End” event is logged to be reported 255 seconds after the programming mode is exited or upon the CLEAR key being pressed and held for three seconds.
Trouble Conditions
The possible trouble conditions are:
AC Power Failure
Communication Failure
Smoke Trouble
Missing Keypad
Fire Trouble
RF Jamming
RF Point Low Battery
Low/No Battery
Silenced Fire Alarm
Call RPM Failed
Non-Telco Fault
Zone Trouble
Telco Line 1 Fault
RF Point Not Reporting
Memory Error
Supervisory Trouble
Silenced Burglar Tamper
Zone Missing
Bell 1 Fault
RF Point Tampering
RF User Device Low Battery
Refer to the Installation manual for a description of these trouble conditions.
Testing
The ZX400/ZX410 provides the following testing capabilities: Walk Test, Battery Test, Bell Test, Communicator Test, Keypad Test and RF Signal Strength Test.
Refer to the appropriate User Guide for instructions on performing these tests. Always ensure that a Walk Test
(and an RF Signal Strength Test when applicable) is performed on a new installation.
9
To test the Received Signal Strength of each RF Zone
Device, use Test 6 - RF Signal Strength Test. From the Control Station press the “8” key, followed by the Installer Code (9632) and then press the “6” key. Next press the RF Zone Device Number (13 to
28). The Control Station will display and sound the
Received Signal Strength of the last transmission sent by the RF Zone Device. See results below:
Strong Signal (HOT or 5 Control Station beeps): a strong or high level RF signal was measured by the receiver for that location of the transmitter. This is a good location for the transmitter and receiver.
Acceptable (ACC or 3 Control Station beeps): a normal or acceptable level of RF signal was measured by the receiver for that location of the transmitter. This is a good location for the transmitter and receiver.
Low Signal (LOW or 1 Control Station beep): a low or not acceptable level of RF signal was measured by the receiver for that location of the transmitter. Make multiple test transmissions, making sure that obstructions between the transmitter and receiver are normal but minimized (hands away from units, metal ladders away from receiver, etc.) during these tests. The transmitter and/or receiver will need to be relocated to obtain ACCEPTABLE level readings.
No Signal (NO or 1 long Control Station beep): no RF signal or an extremely low RF signal was measured by the receiver for that location of the transmitter. Bring the transmitter to the RF Gateway and activate the transmitter. The red LED on the RF Gateway should blink. If it does not, then the transmitter is not working. If the red LED does blink, but the signal strength is still NO SIGNAL, then a programming error exists. Check the programming of the zone in both the RF Gateway and the panel. If the signal strength is STRONG or ACCEPTABLE, then the transmitter and/or receiver will need to be relocated to obtain ACCEPTABLE level readings. Be sure to power down the control to clear out all signal strength levels before testing the transmitter at its new location.
After testing has been completed, the RF Gateway and
RF Zone Devices should be permanently mounted.
NOTE
Series 4000 RF Gateways and transmitters which are not UL Labeled are not allowed in UL Certificated installations.
PROGRAMMING THE CONTROL
Programming the Control
Introduction
The control may be programmed locally from any
LED, SSD, LCD, or VFD Control Station. It may also be programmed using the remote programming software, RPM/2 Pro. Throughout this section, the
Fire Auxiliary key is referred to as the “A” key and the Medical Auxiliary key is referred to as the “C” key.
Local Programming
There are two levels of Control Station programming:
User level and Installer level.
User Level Programming
Provides the ability to add, change, or delete user passcodes. It also allows Scheduled Arming and
Latch Key operation to be changed. A user passcode with authority level 9, 10, or 15 is required to access the user level programming (see Installer Level Programming - Authority Levels). See the appropriate
User Guide for more information regarding user level programming.
Installer Level Programming
Allows total customization of the control’s operating features. Only the installer code may access this level. Anyone attempting installer level programming should be familiar with the contents of this publication prior to programming the control panel.
Remote Programming (RPM/2 Pro)
The entire control database can be programmed remotely through a computer and modem using a remote program called RPM/2 Pro. To use RPM/2
Pro with the ZX400/ZX410, you will need RPM2PRO and a panel support module for the ZX400 family
(PRO400). Remote programming utilizes extensive error checking and security safeguards, including data encryption, password log-on, panel IDs and agency codes.
Panel IDs are used by RPM/2 Pro to identify a control during a remote programming session. The agency code is used by the control to identify the remote programmer during initialization of a remote programming session. These codes are loaded into the control by RPM/2 Pro during the first RPM/2 Pro session. They cannot be viewed by local programming.
The panel ID and agency code work together to prevent illegal takeover by another computer with RPM/2
Pro. Once the agency code is programmed, the control also prevents local changing of account codes and telephone numbers and disables the RESTORE
DEFAULTS function.
NOTE
If the installer code is lost or forgotten, it may be impossible to program the control locally.
If remote programming is used, it is possible to “lockout” or prevent takeover of a control by another installation company by selecting “Lockout Local
Prog.” This prevents the installer passcode from gaining access through local Control Station programming. The installer passcode may still be used for the non-programming functions described in
Installer Level Programming - Authority Levels. Lock-
out Local Prog does not affect remote programming.
Area Partitioning
The control may be divided (partitioned) into two independent areas. To the customer, each area appears to be a full-featured system. This allows one control to be shared by two independent departments within a common structure.
NOTE
LED Control Stations cannot have a
Secondary Area.
Each area can be programmed to control separate outputs with a dedicated audible or annunciator. It is also possible to combine the outputs of both areas so that a central siren, bell or audible can be used. The audible should be positioned so that it can be heard by all partitions. When partitioning is not desired, simply designate all zones to a single area (Area 1).
10
PROGRAMMING THE CONTROL
An example of a partitioning application is a business that is divided into two departments with both departments occupied by a different manager. The control communicator would be installed in a secure area (common utility closet) with dedicated and uninterrupted AC power and telephone service. This must be considered when planning the control panel position as the power and phone service to a tenant may be terminated if that tenant leaves.
Each tenant’s compartment is assigned an area with a number of zones, codes, and Control Stations. When an area experiences an alarm or other event, the adjacent system area is not alerted to the event since the
Control Station would be programmed to respond only to events in the assigned area (see Table 1).
Another programming feature is the ability to allow crossover between areas. This allows the user(s) from one area to operate the other area from a designated Control Station. Programming is discussed in detail later in this manual. By factory default, users are only allowed to see and operate their primary assigned area. Multi-area operation may be useful for applications where the security system is installed in a facility that is divided into departments. Each department has a set of users who are responsible for arming and disarming only the security system to which they are assigned. If desired, the system may be set up to allow one or more users to have control over both areas (see Table 2).
Another programming feature is common area burglar zones (see Operating the System - Introduction).
These zones may be used when a system needs to be configured with two separate areas of protection and a common area. For example, an office building with two separate offices and a common lobby.
The lobby (or common area) only gets armed when both areas are armed in the AWAY mode. When one area is armed in the AWAY mode, the common area becomes an extension of the other area. When either area is disarmed, the common area also is disarmed. Faulted common area zones may be viewed on all Control Stations.
Arming and disarming operations with a common area are the same as without a common area, except that when an area is armed in the AWAY mode, all common area zones may need to be secure.
Common area zones may not be force-armed, but they may be bypassed. Common area zones may be violated while either of the two areas is in Exit or
Entry time countdown.
Maximum Zones = 30
Up to 28 zones may be assigned to either area or the common area (fire zones are system-wide and have no area assignment).
Maximum Users = 50
Any number of users may be assigned to either or both areas.
Maximum Supervised Control Stations = 6
SSD, LCD, and VFD Control Stations can be assigned to operate in both areas if desired. LED Control Stations can only be assigned to operate in either Area
1 or Area 2.
When reporting to the Central Station, the control has three sets of Account Numbers. One set for system events, one set for Area 1 events and one set for
Area 2 events. Examples of System events include:
Fire Alarms and Troubles, Common Area Burglar
Alarms, AC Power Failure, Low Battery and automatic tests. Examples of Area 1 or Area 2 events include:
Burglar Alarms, Holdup Alarms, Opening/Closings.
All events are grouped into several categories with each category having options of reporting to receiver
A, receiver B and/or a Pager.
11
PROGRAMMING THE CONTROL
SYSTEM
System Account Numbers
Fire Zone 30
AREA 1
Area 1 Account Numbers
Burglar Zones 1 - 3
Users 1 - 3
Control Stations 1 & 2
Table 1 Two Separate Areas
AREA 2
Area 2 Account Numbers
Burglar Zones 4 - 6
Users 4 - 6
Control Stations 3 & 4
SYSTEM
System Account Numbers
Common Burglar Zones 7 & 8
Fire Zone 30
AREA 1
Area 1 Account Numbers
Burglar Zones 1 - 3
Users 1 - 3, 7
Control Stations 1, 2, 5
AREA 2
Area 2 Account Numbers
Burglar Zones 4 - 6
Users 4 - 7
Control Stations 3 - 5
Table 2 Two Areas with Two Common Burglar Zones (Zones 7 & 8)
A Multi-Area User Code (User 7) and a Multi-Area Control Station (Keypad 5)
LED Control Station Programming
When in programming mode, an LED Control Station will mimic what is displayed on an SSD Control
Station. The top row of LEDs will correspond to the first SSD character, the second row to the second
SSD character and the third row to the third SSD character. If an SSD character is 1 - 9 or A - F, then that hexadecimal digit will be displayed in binary on the appropriate row of LEDs. See the Installer
Level Programming section for programming with the Control Station. It will also show examples of
SSD, LCD, or VFD Control Station displays. There are no examples for LED Control Stations (see Figure 2).
READY and
TROUBLE LEDs
Flash indicating that the control is in programming mode
READY
TROUBLE
FIRE
1
5
9
2
6
10
3
7
11
4
8
12
ZONE LEDs (1 - 4)
Display hexadecimal value corrresponding to left digit on SSD
Control Station (shown is '5')
ZONE LEDs (5 - 8)
Display hexadecimal value of center digit (shown is '6')
ZONE LEDs (9 - 12)
Display hexadecimal value of right digit (shown is '3')
Value
2
3
4
0
1
7
8
5
6
9
10 (“A”)
11 (“B”)
12 (“C”)
13 (“D”)
14 (“E”)
15 (“F”)
1
Display
2 4
8
Figure 2 LED Display
12
INSTALLER LEVEL PROGRAMMING
Installer Level Programming
Menu Options
Set Clock
This section will describe Installer Level Programming as performed locally from a Control Station.
To enter Installer Level Programming, press the PRO-
GRAM (9) key and enter the installer passcode (default = 9632). The Control Station will then prompt you to select a programming option from 1 to 9 where:
1 = REMOTE CONNECT
2 = SET CLOCK
3 = EDIT FUNCTION MAP
4 = PROGRAMMING ZONE NAMES
5 = PROGRAMMING USER CODES
6 = RESTORE FACTORY DEFAULTS
7 = SET DAYS UNTIL NEXT COMM TEST
8 = CALL RPM
9 = PROGRAM RF DATA
Press the ‘9’ key and enter the installer passcode to enter programming mode. Press the ‘2’ key for Set
Clock programming. The Control Station will go into clock set mode.
The SSD Control Station will have a Set Clock prompt display. The LCD and VFD Control Station will display the current hour, minute, month, day, and year
(HH:MM MM/DD/YY). The zone LEDs on an LED
Control Station will remain off. The hour must be entered in 24-hour format.
14:58 02/11/96
ENTER = COMPLETE
The operator may start entering numbers from the first hour digit. As a number is entered, it is displayed and the cursor automatically moves to the next position on the LCD and VFD Control Station.
When a digit is entered, the Control Station will display:
Remote Connect
Press the ‘9’ key and enter the installer passcode to enter programming mode. Press the ‘1’ key to perform a Remote Connect. The control will seize the telephone line and the Control Station will return to idle. This feature is used to manually connect the control to a remote programming computer.
REMOTE CONNECT
24:58 02/11/96
ENTER = COMPLETE
If the CLEAR key is pressed, the cursor will move back to the first hour digit and any changes that were entered will be erased, i.e.: the current time and date will be re-displayed. If the CLEAR key is pressed and no changes have been entered, the
Control Station will return to idle with no changes to the time or date.
14:58 02/11/96
ENTER = COMPLETE
13
INSTALLER LEVEL PROGRAMMING
If the ENTER key is pressed, all changes that were entered will be range checked. The entire time and date need not be entered. Any fields that are not entered will remain unchanged. If the data entered is within range parameters, the clock will be updated and the Control Station will return to idle. A “Begin
Set Clock” event will indicate the time before the change and an “End Set Clock” event will indicate the time after the change. If the entered data is out of range, the Control Station will indicate an error, erase the previous entries and re-display the current time and date.
INVALID SETTING
Edit Function Map
Press the ‘9’ key and enter the installer passcode to enter programming mode. Press the ‘3’ key to enter Edit Function Map mode. The Control Station will prompt you for a location to be programmed.
The location numbers, definitions, and valid entries for the locations are described in the Installer Level
Programming - Function Map section. From this mode, you may edit the entire Function Map except for User Codes and Zone Names. Editing Zone
Names is described in the Installer Level Programming - Programming Zone Names section. Editing
User Codes is described in the Installer Level Programming - Programming User Codes section.
From the LOCATION prompt, enter digits for the desired location number. The digits entered will be displayed. If more than three digits are entered, the first digit entered will be discarded. If you make a mistake, you may press the CLEAR key to clear out the location and start over. When the desired location number is displayed, press the ENTER key. The
Control Station will then display the current value programmed at that location.
Entering a New Value at a Location
While the Control Station is displaying the value at a location, you can enter digits to change the value at that location. The new value is displayed as you enter the digits. Other keys work as follows:
ENTER
‘C’ Key
- if pressed after new digits are entered, the displayed value is stored at the current location.
- if pressed with no new digits entered, then it will go to the next location.
- if pressed, it will go back one location and ignore any digits entered.
CLEAR
- if pressed after new digits are entered, the new digits will be erased and the original value will be re-displayed at the location.
- if pressed with no new digits entered, then it will return to the LOCATION prompt.
OFF CANCEL - on an LED or SSD Control Station, it will momentarily display the present location number.
NOTE
When you press the ENTER key to store the new value, the system will store the value as entered. It is the responsibility of the programmer to enter a value within the specified range. If the value entered is out of the range, then undesirable operation may occur. In some cases, if the value entered is too large, it will be truncated before it is stored causing a different value to be stored than was entered.
14
Programming Account Code and
Telephone Number Digits
When the location being programmed is an account code or telephone number digit (see Installer Level
Programming - Communication Telephone Numbers
Description and Area Event Reporting Description), the value will be displayed as an “H” followed by a single digit. The “H” indicates that this location is a
Hexadecimal field. The valid entries for these locations are “0” through “F”, where A - F correspond to 10 - 15 respectively.
To program a digit, enter digits as normal. To enter an A - F, enter a ‘1’ followed by a ‘0’ through ‘5’.
As in programming normal fields, if too many digits are entered, the first digit entered will be discarded.
The ENTER, OFF CANCEL, ‘C’, and CLEAR keys will work the same as described above.
Programming Report Codes and Attribute
Fields
When the location being programmed is a report code (see Installer Level Programming - Zone Report Codes Description thru System Report Codes
Description) or an attribute field (see Installer Level
Programming - Area Data Descriptions thru Zone
Data Descriptions and System Report Codes Description thru Area Schedules Description), the value will be displayed as an “H” followed by two digits. The
“H” indicates that this location is a Hexadecimal field.
The valid entries for these locations are “00” through
“FF”, where A - F correspond with 10 - 15 respectively. The Control Station display will automatically display the hexadecimal value.
To program one of these locations, enter digits as normal. To display a ‘1’ in the first digit location, you must enter a ‘0’ before the ‘1’, i.e. ‘01’ displays a ‘1’. To enter an A - F, enter a ‘1’ followed by a ‘0’ through ‘5’. For example:
Enter
1-2-3
0-1-2
1-8
0-1-1-0
1-2
2-1
To Get
C3
12
18
1A
0C
21
INSTALLER LEVEL PROGRAMMING
As in programming normal fields, if too many digits are entered, the first digit entered will be discarded.
The ENTER, OFF CANCEL, ‘C’, and CLEAR keys will work the same as described above.
Additional Programming Notes
To exit out of Edit Function Map mode and return the Control Station to the idle state, press the CLEAR key from the LOCATION prompt. (You may need to press the CLEAR key several times to get to the LO-
CATION prompt). An “End Local Programming” event will not be logged until 255 seconds after you exit programming mode. This is to allow you to exit and re-enter programming mode repeatedly without logging each one. To force an “End Local
Programming” event to be logged, immediately (i.e.: to have it reported to the Central Station), press and hold the CLEAR key for three seconds.
When programming the value at the last programming location, the Control Station will return to the
LOCATION prompt if the ENTER key is pressed.
If the panel has been programmed from RPM/2 Pro and the Agency Code has been loaded into the panel, then the locations corresponding to the telephone numbers and account codes will not be editable.
Programming Zone Names
Only the LCD and VFD Control Station may be used to program zone names. Press the ‘9’ key and enter the installer passcode to enter programming mode.
Press the ‘4’ key to program the zone names. The
Control Station will prompt you for a Zone ID to be programmed. The valid Zone IDs are 1 to 30.
Enter a number corresponding to the Zone ID and press ENTER. Once a valid Zone ID is selected, the control will display the Zone ID and the current Zone
Name with the cursor on the first character. Press the key associated with each character. Each keypress will change the display to the next character listed for that key. The characters available for programming the Zone Names are located on the next page.
15
INSTALLER LEVEL PROGRAMMING
Key #1
0 1 2 3 4 5 6 7 8 9 : ; < = > ? @
Key #2
A B C
Key #3
D E F
Key #4
G H I
Key #5
J K L
Key #6
M N O
Key #7
P Q R S
Key #8
T U V
Key #9
W X Y Z [ ¥ ] ^ _
Key #0
space ! “ # $ % & ‘ * + , - . /
‘A’ Key
Used to move the cursor back one position
‘C’ Key
Used to move the cursor forward one position
If the ENTER or CLEAR key is pressed and no changes have been made, the Control Station will return to the Zone ID prompt. If the CLEAR key is pressed and changes have been made, all changes will be cleared and the Control Station will return to displaying the original Zone Name. To save any changes made to the Zone Name, press the ENTER key. The
Control Station will return to the Zone ID prompt.
Press the CLEAR key to return to idle.
Programming User Codes
The installer passcode has the authority to program user passcodes locally if Lockout Local Installer Programming is disabled. The control may be programmed with up to 50 user passcodes. See Installer
Level Programming - User Data Description for instructions on setting the authority level and area assignment for each passcode. To program or change a user passcode:
1. Press the ‘9’ key and enter the installer passcode to enter programming mode.
2. Press the ‘5’ key to Program User Codes. The
Control Station will prompt you to enter the User
ID of the passcode that you wish to program.
3. Enter the ID number and press the ENTER key.
4. Enter the new four-digit passcode. The Control
Station will beep twice and return to the User ID prompt.
5. Enter a new ID number or press the CLEAR key to exit.
The entire passcode is displayed on an LCD/VFD
Control Station. Only one digit at a time is displayed on an SSD Control Station. To view the existing passcode on an SSD Control Station, press the EN-
TER key after each digit is displayed.
If the new passcode being entered is a duplicate of an existing one, the Control Station will sound an error tone and return to the first digit location so that you may try again. To make a User passcode inoperable, enter “0000” as the new four-digit passcode.
16
Restore Factory Defaults
This function provides a means to completely wipe out the panel’s memory and restore it to a factory default state. If successfully completed, the panel will:
• default the entire Function Map (including Zone
Names and User Passcodes)
• clear the Event Log and log a “System Startup” event
• clear all alarm, trouble and armed conditions
• not affect the System Clock (time and date)
• not affect data programmed in the RF Gateway(s)
If the panel has been programmed from RPM/2 Pro and the Agency Code has been loaded into the panel, then this function will be disabled.
Press the ‘9’ key and enter the installer passcode to enter programming mode. Press the ‘6’ key to enter Restore Factory Defaults mode. The Control Station will prompt you to select the default mode.
ENT 0=STANDARD
1=COMM FIRE
For a ZX400 or ZX410, enter 0. For a ZX440F, enter
1. To convert a ZX410 to a ZX440F with a ZXCFK
(Commercial Fire Kit), you must default the panel with option 1. Once the default mode is selected, the Control Station will prompt you to re-enter the installer passcode for verification.
INSTALLER LEVEL PROGRAMMING
Days Until Next Comm Test
The scheduling of Automatic Communications Tests requires programming a “Comm Test Time-of-Day” and the number of “Days Between Comm Tests” as described in Installer Level Programming - Communicator Data Description. If “Days Between Comm
Tests” is zero, then no automatic comm tests will occur. Otherwise, a comm test will occur when a
Days Until the Next Comm Test counter ticks down to zero. This function allows you to view that Days counter. If the value displayed is zero or one, then the next comm test will occur at the next “Comm
Test Time-of-Day”. This function also allows you to change the number of Days Until the Next Comm
Test.
Press the ‘9’ key and enter the installer passcode to enter programming mode. Press the ‘7’ key to enter Days Until Next Comm Test programming. The
Control Station will display the number of days until the next scheduled comm test.
To change this value, enter a number between 0 and 255. If a mistake is made, press the CLEAR key to start over. If a number greater than 255 is entered, the first digit entered will be discarded. When the desired number of days is displayed, press the
ENTER key. The Control Station will return to idle.
To exit out of this function without adjusting the number of days, press the CLEAR key.
Call RPM
This option is not available at this time.
TO DEFAULT PANEL
ENTER PASSCODE
If it is entered correctly, the Control Station will go back to the system powering up display.
17
INSTALLER LEVEL PROGRAMMING
Program RF Data
In order for an RF Zone Device or RF User Device to be received by an RF Gateway, the address of the RF
Device must be programmed into the RF Gateway
(as described in the next two sections). The ZX400/
ZX410 can support up to 12 RF User Devices per RF
Gateway and up to 16 RF Zones. The 16 RF Zones are programmed into the RF Gateways as devices
13-28 corresponding to zones 13-28. The 12 RF
User Devices are programmed into a RF Gateway as devices 1-12 in any order (there is no correlation between these devices and the Control Panel’s configuration data). The 4710 RF Gateway is restricted to devices 13-20 for zones 13-20 and devices 1-6 for six RF User Devices.
Programming RF Zone Devices Into the RF
Gateway
Press the ‘9’ key and enter the installer passcode to enter programming mode. Press the ‘9’ key to Program RF Data. The Control Station prompts you to select an RF Gateway to program. Press ‘1’ or ‘2’.
The Control Station then prompts you to select an
RF Device to program.
Enter 13 thru 28 to select an RF Zone and press
ENTER. The Control Station displays the eight digits that are currently programmed in the RF Gateway for that zone. For each digit, you may program a new value by pressing a digit key. The Control
Station will automatically move to the next digit.
To move to the next digit without changing the current digit, press the ENTER key.
The first digit to enter is the Supervision setting where:
0 = Unsupervised
1 = 200 Seconds
2 = 1 Hour
3 = 4 Hours
4 = 24 Hours
The next seven digits to enter come directly off of a label on the RF Device.
If you make a mistake while entering the eight digits, press the CLEAR key and the Control Station returns to the first digit.
18
After the last digit is entered, the data is sent to the
RF Gateway and is confirmed and the Control Station returns to the RF Device selection prompt. If the data is successfully loaded into the RF Gateway, the Control Station beeps twice. If the RF Gateway does not respond, the Control Station sounds an error tone and briefly displays an error message.
Check the data bus connections to the RF Gateway.
If the 8 digit number entered for the RF Zone is already stored in the RF Gateway for another zone, the Control Station sounds an error tone and briefly displays a message indicating the duplicate zone.
From the RF Device prompt, select another RF Zone
Device or press the CLEAR key to return to the RF
Gateway prompt. From the RF Gateway prompt you can switch to program the other RF Gateway (if applicable) or press the CLEAR key to exit.
One RF Zone Device may be programmed into both
RF Gateways, but it must be programmed into a different zone on each gateway. When programming
RF Zone Data into two RF Gateways, be sure to note which zones are programmed into each RF Gateway. When the zones are then programmed into the Control Panel, select the correct RF Gateway as the Expansion Device for that zone.
Programming RF User Devices Into the RF
Gateway
Press the ‘9’ key and enter the installer passcode to enter programming mode. Press the ‘9’ key to Program RF Data. The Control Station prompts you to select an RF Gateway to program. Press ‘1’ or ‘2’.
The Control Station then prompts you to select an
RF Device to program.
Enter 1 thru 12 to select an RF User Device and press
ENTER. The Control Station displays the eight digits that are currently programmed in the RF Gateway for that device. For each digit, you may program a new value by pressing a digit key. The Control Station will automatically move to the next digit.
To move to the next digit without changing the current digit, press the ENTER key.
The first digit to enter assigns the RF User Device to a keypad. This is required to determine the area of operation of the RF User Device and for the Access function. Enter ‘1’ thru ‘6’ for a keypad assignment.
INSTALLER LEVEL PROGRAMMING
The second digit to enter defines the operation of the key(s) on the RF User Device, where:
SEC KEY
DIGIT A
1
2
3
4
5
6
7
8
9
KEY
B
AWAY
AWAY
AWAY
AWAY
STAY
STAY
STAY
STAY
AWAY STAY
AWAY PANIC/HOLDUP
STAY
STAY
AWAY
PANIC/HOLDUP
PANIC/HOLDUP
ENTER 4
KEY
C
KEY
D
NIGHT OFF/CANCEL
ACCESS OFF/CANCEL
PANIC/HOLDUP OFF/CANCEL
AUX/MED OFF/CANCEL
ENTER 4
ENTER 4
OFF/CANCEL
OFF/CANCEL
ENTER 4
AUX/MED
ENTER 6
OFF/CANCEL
OFF/CANCEL
OFF/CANCEL
The next six digits to enter come directly off of a label on the RF User Device.
If you make a mistake while entering the eight digits, press the CLEAR key and the Control Station returns to the first digit.
After the last digit is entered, the data is sent to the
RF Gateway and is confirmed and the Control Station returns to the RF Device selection prompt. If the data is successfully loaded into the RF Gateway, the Control Station beeps twice. If the RF Gateway does not respond, the Control Station sounds an error tone and briefly displays an error message.
Check the data bus connections to the RF Gateway.
If the 8 digit number entered for the RF User Device is already stored in the RF Gateway for another device, the Control Station sounds an error tone and briefly displays a message indicating the duplicate device.
From the RF Device prompt, select another RF User
Device or press the CLEAR key to return to the RF
Gateway prompt. From the RF Gateway prompt you can switch to program the other RF Gateway (if applicable) or press the CLEAR key to exit. In most cases, you can program an RF User device into both
RF Gateways.
Programming RF Devices Into the Control Panel
After the RF Devices have been programmed into the RF Gateway, they must also be programmed in the Control Panel. The programming options for the
Control Panel’s Function Map are described in Installer Level Programming - Function Map. When
RF Devices are used in an installation, be sure to consider the following:
For an RF Zone Device, the zone data described in
Installer Level Programming - Zone Data Descriptions must be programmed for the selected zone.
The Zone Type, Area Number and Burglar Zone Attributes locations are programmed as usual. The
Expansion Device location must be set to the appropriate RF Gateway for the zone. The first digit of
Zone Attributes location doesn’t need to be programmed because it is ignored for Wireless Zones, but the second digit must be programmed as usual.
For an RF User Device, a user passcode must be created that consists of the last four digits of the RF
Device’s address (see Installer Level Programming -
Programming User Codes). An appropriate authority level and area assignment must also be programmed for that user (see Installer Level Programming - User Data Description). It is also required that either the area assignment of the user passcode or the area assignment of the associated keypad must be a single area (i.e. an RF User Device on an RF
Gateway can only operate on one area). An RF User
Device can be programmed into two RF Gateways with different keypad assignments on each. If the device’s passcode is operational in both areas and the keypad on one RF Gateway is operational in one area and the keypad on the other RF Gateway is operational on the other area, then the RF User Device can operate on either area depending on which
RF Gateway detects it.
For UL 1637 Home Health Care, RF
User Devices may only be assigned to user passcodes 1-30.
19
INSTALLER LEVEL PROGRAMMING
Function Map
To edit the Function Map, press the PROGRAM (9) key, enter the installer passcode, and press the ‘3’ key to select the Edit Function Map programming option. The Control Station will prompt for a location to be programmed. All function map locations can be programmed except for user codes and zone names.
NOTE
When entering values into the programming locations, it is possible to enter values which exceed the valid range of the programmed options. It is the responsibility of the installer to ensure the correct value of any entry programmed into the control. The valid entries for each location are detailed in the following sections.
Area Data Descriptions
The following table refers to programming locations
1 through 20.
ITEM
AWAY Exit Delay Time
VALID RANGE
0 to 255 seconds
STAY & NIGHT Exit Time 0 to 255 seconds
DESCRIPTION
Time in seconds for all Burglar zones, may be audibly annunciated. (See Inst. Level Prog. - Prog. Notes, Note 1).
Time in seconds for all Burglar zones, always silent.
Entry Delay Time 1
Entry Delay Time 2
Panic Key Alarms
Closing Ringback
Burglar Audible Lockout
0 to 255 seconds
0 to 255 seconds
Pre-Alarm Warning Time 0 to 255 seconds
00 to 33
(see the Panic Key Table)
Time in seconds to enter Burglar zones defined as Delay #1, may be audibly annunciated. (See Inst. Level Prog. - Prog. Notes, Note 1A).
Time in seconds to enter Burglar zones defined as Delay #2, may be audibly annunciated.
Time in seconds to correct a false alarm, always audible.
(See Inst. Level Prog. - Prog. Notes, Note 2).
The first digit defines the annunciation of an alarm activated by the Police key. The second digit defines the annunciation of an alarm activated by the Medical/Emergency key. Either key may also be used to initiate a call to a pager.
Determines how the system annunciates the successful transmission of an AWAY closing report to the Central Station.
0 = Ringback Output
1 = Ringback Output and
Keypads
2 = Ringback Output, Bell
Output and Keypads
0 = No Lockout
1 to 15 = Alarms for an Area
20
Determines the number of times that a Bell Output may be activated during an armed cycle, resets with disarm.
ITEM
Swinger Shunt
Area Attributes
INSTALLER LEVEL PROGRAMMING
VALID RANGE
0 = No Shunt
1 to 15 = Violations for a Zone
00 to FF
(see the Area Attribute Table)
DESCRIPTION
Determines the number of violations that may occur from an armed burglar zone before that zone is automatically bypassed.
• Bypassing - enables selective bypassing of any zone that is defined as bypassable in this area.
• Force-Arming - permits arming of the area with zones faulted.
Faulted zones are temporarily bypassed and return to operation if the fault is corrected. Only zones that are defined as bypassable may be force-armed. (See Inst. Level Prog. - Prog.
Notes, Note 4).
• Exit Arm - (See Inst. Level Prog. - Prog. Notes, Note 3).
• 3 Second Panic Keys - requires all panic keys to be pressed and held for approximately 3 seconds in order to activate alarm condition. Only pertains to Control Stations that are Primary to this area.
• Double Press Panic Keys - requires all panic keys to be pressed twice within one second to activate. Only pertains to Control
Stations that are Primary to this area.
• Two Button Arm - enables quick arming by pressing AWAY,
STAY, or NIGHT followed by the ENTER key. Cannot be used with force-arming.
• Double Press Arm - enables quick arming by pressing AWAY,
STAY, or NIGHT twice. Cannot be used with force-arming.
• Open After Alarm - enables opening reports to be reported only if they occur after an alarm. All “opening” events will be logged in the Event Log regardless of setting.
• Display Bypass Armed - when armed in STAY or NIGHT mode with bypassed or force-armed zones, Control Stations with the area as the Primary area will indicate that there are zones that are bypassed.
21
INSTALLER LEVEL PROGRAMMING
Area Data Default Table
AWAY Exit Time (sec)
STAY/NIGHT Exit Time (sec)
Entry Time 1 (sec)
Entry Time 2 (sec)
Pre-Alarm Time (sec)
Panic Key Alarms
Closing Ringback
Burglar Audible Lockout
Swinger Shunt
Area Attributes
[4]
[5]
[6]
[7]
Loc
[1]
[2]
[3]
[8]
[9]
[10]
AREA 1
Default
60
60
20
40
0
H-21
0
0
0
H-09
[14]
[15]
[16]
[17]
Loc
[11]
[12]
[13]
[18]
[19]
[20]
AREA 2
Default
60
60
20
40
0
H-21
0
0
0
H-09
Panic Key Table
FIRST DIGIT
0 = No Keypad Sounder or Bell Output (invisible)
1 = Keypad Sounder Only
2 = Keypad Sounder and Bell Output
3 = Call Pager, No Alarm
If the First Digit entered is ’1‘, it must be entered as ’01‘
SECOND DIGIT
0 = No Keypad Sounder or Bell Output (visible)
1 = Keypad Sounder Only
2 = Keypad Sounder and Bell Output
3 = Call Pager, No Alarm
Area Attribute Table
FIRST DIGIT
All Features Below Disabled
Two Button Arm
Double Button Press Arm
Open After Alarm
Display Bypassed Armed
ENTER FOR:
•
0 1 2 3 4 5 6 7 8 9 A B C D E F
•
• •
• •
• •
• • • •
• •
• •
• •
• •
• • • •
• • • • • • • •
•
SECOND DIGIT
Double Press Panic Keys
Bypass
Force-Arm
Exit Arm
3 Second Panic Keys
• • • • • • • •
•
• •
•
•
• •
• • • •
• •
• •
•
•
•
•
•
•
•
•
• •
•
• • • •
If the First Digit entered is ‘1’, it must be entered as ‘01’. A = 10; B = 11; C = 12; D = 13; E = 14; F = 15
•
•
22
INSTALLER LEVEL PROGRAMMING
Keypad Data Descriptions
Keypad Data Default Table
KEYPAD 1 KEYPAD 2 KEYPAD 3 KEYPAD 4 KEYPAD 5 KEYPAD 6
Loc Default Loc Default Loc Default Loc Default Loc Default Loc Default
Keypad Type
Keypad Attribute
Access Time (sec)
LED
[21] H-1C
[22] 5
LED SSD SSD
[23] H-1C [25] H-1C [27] H-1C
[24] 5 [26] 5 [28] 5
LCD/VFD LCD/VFD
[29] H-1C [31] H-1E
[30] 5 [32] 5
The following table refers to programming locations
21 through 32.
ITEM
Keypad Attributes
VALID RANGE
00 to FF
(see the Keypad Attribute table.)
Access Time 0 = Toggle
1 - 255 seconds
DESCRIPTION
• Primary Area 1 or 2 - determines which area the Control
Station’s status indicator will reflect and which area the Control Station will display area status for when it is idle.
• Secondary Area Enabled - (See Inst. Level Prog. - Prog. Notes,
Note 5).
• ‘A’ Key Enabled - defines if the Fire key is to be enabled at this
Control Station.
• ‘B’ Key Enabled - defines if the Police key is to be enabled at this Control Station.
• ‘C’ Key Enabled - defines if the Medical/Emergency key is to be enabled at this Control Station.
• Silent Exit Time - silences the exit alert at the Control Station.
• Silent Entry Time - silences the entry alert at the Control Station. This does not affect Pre-Alarm Warning Time.
• Silent Trouble - silences the trouble conditions at the Control
Station.
• Time in seconds for an access output activated from this Control Station. Toggle access feature allows the output to latch
ON/OFF.
• All access outputs assigned to this Control Station are affected when the access function and a valid code is entered for this
Control Station (See Inst. Level Prog. - Output Definitions Description). It is not area dependent. Typically used to activate electrically operated door strikes.
This control is not a UL Listed Access Control System. The access feature should not be used in UL
Listed installations.
23
INSTALLER LEVEL PROGRAMMING
Keypad Attribute Table
FIRST DIGIT
All Features Below Disabled
‘C’ Key Enabled
Silent Exit Time
Silent Entry Time
Silent Troubles
ENTER FOR:
•
0 1 2 3 4 5 6 7 8 9 A B C D E F
•
• •
• •
• •
•
• • • •
•
• •
• •
• •
• •
• •
• • • • • • • •
•
SECOND DIGIT
Primary Area 1
• • •
Primary Area 2
• • • •
Primary Area 1, Secondary Area 2
• • • •
Primary Area 2, Secondary Area 1
‘A’ Key Enabled
‘B’ Key Enabled
•
• • •
•
•
• • •
•
•
•
•
•
•
•
•
If the First Digit entered is ‘1’, it must be entered as ‘01’. A = 10; B = 11; C = 12; D = 13; E = 14; F = 15
•
•
•
24
INSTALLER LEVEL PROGRAMMING
Zone Data Descriptions
Zone Data Default Table
ZONE
TYPE
Loc Default
Zone 16
Zone 17
Zone 18
Zone 19
Zone 20
Zone 21
Zone 22
Zone 23
Zone 24
Zone 25
Zone 26
Zone 27
Zone 28
Zone 29*
Zone 30**
Zone 01
Zone 02
Zone 03
Zone 04
Zone 05
Zone 06
Zone 07
Zone 08
Zone 09
Zone 10
Zone 11
Zone 12
Zone 13
Zone 14
Zone 15
[136]
[141]
[146]
[151]
[156]
[161]
[163]
[96]
[101]
[106]
[111]
[116]
[121]
[126]
[131]
[77]
[81]
[86]
[91]
[61]
[65]
[69]
[73]
[33]
[37]
[41]
[45]
[49]
[53]
[57]
1
0
2
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
AREA
Loc Default
[97]
[102]
[107]
[112]
[117]
[122]
[127]
[132]
[137]
[142]
[147]
[152]
[157]
[78]
[82]
[87]
[92]
[62]
[66]
[70]
[74]
[34]
[38]
[42]
[46]
[50]
[54]
[58]
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
0
1
1
1
1
1
1
1
1
1
1
1
EXPANSION
DEVICE
Loc Default
[118]
[123]
[128]
[133]
[138]
[143]
[148]
[153]
[158]
[83]
[88]
[93]
[98]
[103]
[108]
[113]
* Zone 29 is the Two-Wire Smoke Zone on the ZXEXP Module
** Zone 30 is the Two-Wire Smoke Zone on the Control Board
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
ZONE
ATTRIBUTE
Loc Default
[100] H-37
[105] H-37
[110] H-37
[115] H-37
[120] H-37
[125] H-37
[130] H-37
[135] H-37
[140] H-37
[145] H-37
[150] H-37
[155] H-37
[160] H-37
[162] H-63
[164] H-63
[80]
[85]
[90]
[95]
[64]
[68]
[72]
[76]
[36]
[40]
[44]
[48]
[52]
[56]
[60]
H-37
H-37
H-37
H-37
H-37
H-37
H-37
H-37
H-37
H-37
H-37
H-37
H-37
H-37
H-37
BURGLAR ZONE
ATTRIBUTE
Loc Default
[99] H-0C
[104] H-0C
[109] H-0C
[114] H-0C
[119] H-0C
[124] H-0C
[129] H-0C
[134] H-0C
[139] H-0C
[144] H-0C
[149] H-0C
[154] H-0C
[159] H-0C
[79]
[84]
[89]
[94]
[63]
[67]
[71]
[75]
[35]
[39]
[43]
[47]
[51]
[55]
[59]
H-0C
H-0C
H-0C
H-0C
H-0C
H-0C
H-0C
H-0C
H-0D
H-03
H-03
H-0C
H-0C
H-0C
H-0C
25
INSTALLER LEVEL PROGRAMMING
The following table refers to programming locations
33 - 164.
ITEM VALID RANGE
Zone Type
Note: Zone 29 & 30 may only be programmed as
24 Hour Fire, Verified
Fire, Fire Supervisory or
Not Used; any other will be interpreted as Not
Used. All other zones may be programmed as any zone type.
0 = Not Used
1 = Burglar
2 = 24 Hour Fire
3 = 24 Hour Holdup
4 = 24 Hour Auxiliary
5 = Momentary Keyswitch
(Arm AWAY/Disarm)
6 = 24 Hour Communicator
7 = 24 Hour Burglar Tamper
8 = Universal
9 = Universal Logged
10 = Verified Fire
Area Number
Expansion Device
Burglar Zone Attributes
Zone Attributes
11 = Fire Supervisory
12 = Listen-In Module Input
13 = Reserved
14 = 24 Hour Non-Alarm
0 = Disable
1 = Area 1
2 = Area 2
3 = Common Area
0 = ZXEXP
1 = RF Gateway 1
2 = RF Gateway 2
3 = ZEM
00 to FF
(see the Burglar Zone
Attribute Table)
00 to FF
(see the Zone Attribute Table)
DESCRIPTION
• Critical Condition Monitor (CCM), no local display.
• May be used to activate an output that is programmed as Universal. Only the Universal Logged is posted in the Event Log when activated. No events are reported to the Central Station.
• Upon activation, control resets switched smoke power. The loop is ignored for 30 seconds. Subsequent activation within the next 60 seconds causes an alarm.
• See Inst. Level Prog. - Prog. Notes, Note 11.
• Communicator with local display.
• Determines which area the zone belongs to. Fire zones are visible to both areas regardless of settings. Only Burglar zones may be assigned to the Common Area (see Operating the
System - Introduction).
• Determines which data bus device the system will poll to get the zone’s status data.
• See Inst. Level Prog. - Prog. Notes, Note 2, 6, and 7 for a complete description of the Burglar Zone Attributes.
• Bell Output on Alarm - determines if Bell Output activates due to an alarm from the zone. (See Inst. Level Prog. - Prog.
Notes, Note 8).
• Keypad Sounder on Alarm - determines if Control Station sounder activates due to an alarm from the zone. (See Inst.
Level Prog. - Prog. Notes, Note 8).
• Bypassable - determines if a zone may be bypassed or forcearmed. (See Inst. Level Prog. - Prog. Notes, Note 9).
• Secure Watch - (See Inst. Level Prog. - Prog. Notes, Note 10).
• Zone Supervision - determines how opens and shorts are handled.
• Fast Zones - only applies to zones 1 - 12. A Fast Zone on zones 1 - 6 has a loop response time of 80 msec. A Fast Zone on zones 7 - 12 has a loop response time of 20 msec.
26
INSTALLER LEVEL PROGRAMMING
Burglar Zone Attribute Table
FIRST DIGIT
Standard (all below disabled)
Chime Always
Verifying
Self-Verifying
Sentry Test
SECOND DIGIT
Instant
Delay 1
Delay 2
Follower
Arm STAY
Arm NIGHT
ENTER FOR:
•
0 1 2 3 4 5 6 7 8 9 A B C D E F
•
•
•
• •
•
•
Armed AWAY only
(interior)
•
•
•
• •
•
• • • •
•
Armed AWAY &
STAY
•
• •
•
•
•
•
•
•
• •
• •
• •
•
• • • •
• • • • • • • •
Armed AWAY &
NIGHT
Armed AWAY, STAY &
NIGHT (perimeter)
•
• •
• •
• • •
•
•
•
•
•
•
•
•
•
•
Zone Attribute Table
FIRST DIGIT
Invalid
Alarm on Open - No Trouble
(EOL optional)
Alarm on Short - No Trouble
(EOL optional)
•
•
ENTER FOR:
0 1 2 3 4 5 6 7 8 9 A B C D E F
•
•
• •
Alarm on Open or Short - No Trouble
(with EOL)
•
•
Trouble on Open or Short
• •
Alarm on Open - Trouble on Short
•
•
Alarm on Short - Trouble on Open
• •
Alarm on Open or Short - Trouble on Open when disarmed (Burg only)
Fast Zones
•
• • • • • •
SECOND DIGIT
All Features Below Disabled
•
Bell Output on Alarm
Keypad Sounder
Bypassable
Secure Watch
•
•
•
•
•
•
• •
• •
•
• • • •
• •
• •
•
•
• •
• • • • • •
•
•
•
If the First Digit entered is ‘1’, it must be entered as ‘01’. A = 10; B = 11; C = 12; D = 13; E = 14; F = 15
• The first digit of the zone attribute is ignored for RF and ZEM zones.
• The only valid zone attributes for Zones 29 and 30 are ‘63’, ‘65’, ‘66’ and ‘67’.
•
•
27
INSTALLER LEVEL PROGRAMMING
User Data Description
The user data block is used to set the level of authority that determines the level of activity the user can perform on the control and the areas that a particular user can perform operations on. The passcodes associated with each user may be programmed as described in Installer Level Programming - Programming User Codes.
User Data Code Default Table
CODE
Default
AUTHORITY
LEVEL
Loc Default
User 09
User 10
User 11
User 12
User 13
User 14
User 15
User 16
User 01
User 02
User 03
User 04
User 05
User 06
User 07
User 08
User 17
User 18
User 19
User 20
User 21
User 22
User 23
User 24
User 25
0000
0000
0000
0000
0000
0000
0000
0000
1234
0000
0000
0000
0000
0000
0000
0000
0000
0000
0000
0000
0000
0000
0000
0000
0000
[181]
[183]
[185]
[187]
[189]
[191]
[193]
[195]
[165]
[167]
[169]
[171]
[173]
[175]
[177]
[179]
[197]
[199]
[201]
[203]
[205]
[207]
[209]
[211]
[213]
6
6
6
6
6
6
6
6
6
6
6
6
6
6
10
6
6
6
6
6
6
6
6
6
6
OPERATION
AREA
Loc Default
[182]
[184]
[186]
[188]
[190]
[192]
[194]
[196]
[166]
[168]
[170]
[172]
[174]
[176]
[178]
[180]
[198]
[200]
[202]
[204]
[206]
[208]
[210]
[212]
[214]
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
User 34
User 35
User 36
User 37
User 38
User 39
User 40
User 41
User 26
User 27
User 28
User 29
User 30
User 31
User 32
User 33
User 42
User 43
User 44
User 45
User 46
User 47
User 48
User 49
User 50
CODE
Default
0000
0000
0000
0000
0000
0000
0000
0000
0000
0000
0000
0000
0000
0000
0000
0000
0000
0000
0000
0000
0000
0000
0000
0000
1245
AUTHORITY
LEVEL
Loc Default
[231]
[233]
[235]
[237]
[239]
[241]
[243]
[245]
[215]
[217]
[219]
[221]
[223]
[225]
[227]
[229]
[247]
[249]
[251]
[253]
[255]
[257]
[259]
[261]
[263] 10
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
OPERATION
AREA
Loc Default
[232]
[234]
[236]
[238]
[240]
[242]
[244]
[246]
[216]
[218]
[220]
[222]
[224]
[226]
[228]
[230]
[248]
[250]
[252]
[254]
[256]
[258]
[260]
[262]
[264]
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
3
1
1
1
1
28
INSTALLER LEVEL PROGRAMMING
The following table refers to programming locations
165 - 264.
ITEM VALID RANGE
Authority Level 0 to 15
Areas of Operation 0 = Disabled
1 = Area 1
2 = Area 2
3 = Both
DESCRIPTION
See table on following page for Authority Level options.
(Enter 0 to disable).
Determines which areas the passcode can be used to perform operations on. If a 3 is selected, the Control Station it is used on must be programmed for both areas in order to access both areas.
Authority Levels
Authorities levels 1 through 10 are the general purpose levels with level 10 having the highest capabilities. Level 11 is for limited disarm capabilities
(ie: Maid’s passcode). Level 12 is for User on Premises reporting. Level 13 is for Duress reporting.
For High Level Security applications, only levels 14 and 15 should be used. If levels 14 and 15 are used, all other users should be set to Level 0 (zero).
Level 14 needs 2 different level 14 passcodes in order to activate any of the options available. The
Control Station will beep 4 times after the 1st passcode is entered signifying that it has been accepted. The 2nd passcode may then be entered.
Level 15 is for maintenance activities only. Level 15 does not allow the user to arm or disarm the system, only to maintain it.
See the table on the next page for the options available for each authority level. To disable all capabilities, set the authority level to zero (0).
The Installer passcode has the authority level to perform the following operations:
Access from Keypad *
Arm (AWAY, STAY, NIGHT) *
Disarm if Armed by an Installer *
Change Arming Level *
Edit User Codes *
Edit Zone Names *
Force-Arm *
View & Print Event Log *
Bypass Zones *
Chime Enable/Disable *
Default Function Map *
Edit Function Map (except Zone Names & User Codes) *
Silence/Cancel Alarm if not Armed or if Armed by Installer *
Silence Bell without Disarm if Armed by other than Installer
Initiate Call to RPM/2 Pro
Remote Connect
Reset Smoke Power
Program RF Data
RF Signal Strength
Set Clock
Silence Trouble
View Alarm Memory
Battery Test
Bell Test
Comm Test
Keypad Test
Walk Test
Adjust Days Until Next Auto Comm Test
∗
Disabled if Lockout Local Programming is enabled (see Installer Level Programming - Programming Options).
29
INSTALLER LEVEL PROGRAMMING
CAPABILITIES
Access From Keypad
Chime Enable/Disable
Silence Bell Without Disarm
Arm (AWAY, STAY, NIGHT)
Changing Arming Level
Remote Connect
Silence/Cancel Alarm
Silence Trouble
Disarm
View Alarm Memory
Reset Smoke Power
Bypass Zones
Force-Arm
Abort Exit Arm
Walk Test
Comm Test
Bell Test
Battery Test
Keypad Test
RF Signal Strength Test
Delay Scheduled Arming
View & Print Event Log
Edit Scheduled Arming
Edit Latch Key Operation
Set Clock
Abort Auto-Arming
Edit Zone Names
Edit User Codes
Disarm If Armed By A Level 11
User Passcode
Silence/Cancel Alarm If Not Armed
Or If Armed By A Level 11 Passcode
Silence Bell Without Disarm If Armed
By Other Than A Level 11 Passcode
Access From Keypad With User On
Premises Report
•
•
AUTHORITY LEVEL
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
•
• • • • •
• • • • •
•
• • •
•
•
• • • • •
• •
• •
•
•
•
• • • •
• • •
• • • • •
• • • • • •
• • • • • • • •
•
•
•
•
•
• •
•
•
•
• •
•
• •
•
•
•
•
• • •
•
•
•
•
•
•
•
•
•
• • • • •
• • • •
• • • •
• • • •
• • • •
• • • •
• • • •
• • •
• • •
• •
• •
• •
• •
• •
•
•
•
•
• •
•
• •
•
•
••
••
••
•• ••
••
••
••
••
••
• • ••
••
••
••
••
••
••
••
••
••
••
••
•
•
•
•
Silence/CancelAlarm With User On
Premises Report
•
Disarm With User On Premises Report
•
✝
Access From Keypad With Duress
Arm (AWAY, STAY, NIGHT) with Duress
Change Arming Level With Duress
Force-Arm With Duress
Silence/Cancel Alarm With Duress
Disarm With Duress
•
•
•
•
•
•
✝
•• For High Level Security applications only
✝
The Off/Cancel key followed by a Duress or User On Premises passcode will always produce a ”Duress“ or ”User On Premises“ report regardless of whether the system was armed.
30
INSTALLER LEVEL PROGRAMMING
Output Definitions Description
This data block is used to assign the programmable outputs. The ZX400/ZX410 Control Board is equipped with one programmable output (PGO1) and one bell output (BELL). Additional outputs can be obtained in groups of ten by the addition of output driver modules (ZXODM) or a zone expander
(ZXEXP). The 10 outputs on ODM2 are identical to the 10 outputs on the zone expander.
Each output is assigned a condition (i.e.: Burglar,
Fire, Status, Alarm) and areas to which it should respond when the condition is active in those areas.
For access conditions, the output is assigned to a
Control Station(s). Output conditions 1 - 12 ignore the area setting.
Output Definitions Default Table
CONDITION AREA OR KEYPAD
Loc Default Loc Default
Control Bell
Control PGO1
ODM 1
Output 01
Output 02
Output 03
Output 04
Output 05
Output 06
Output 07
Output 08
Output 09
Output 10
[266] 17
[268] 13
[270] 3
[272] 14
[274] 15
[276] 19
[278] 31
[280] 18
[282] 25
[284] 34
[286] 39
[265]
[267]
[269]
[271]
[273]
[275]
[277]
[279]
[281]
[283]
[285]
[287]
1
1
1
1
1
1
1
1
1
1
1
1
CONDITION AREA OR KEYPAD
Loc Default Loc Default
Zone Expander or ODM 2
Output 01
Output 02
Output 03
Output 04
Output 05
Output 06
Output 07
Output 08
Output 09
Output 10
[288]
[290]
[292]
[294]
[296]
[298]
[300]
[302]
[304]
[306]
13
31
18
25
34
39
3
14
15
19
[289]
[291]
[293]
[295]
[297]
[299]
[301]
[303]
[305]
[307]
1
1
1
1
1
1
1
1
1
1
Output conditions 39 and 40 add combinations of keypads 1 - 6.
Conditions 13 - 38 are specified as a combination of Areas 1 & 2.
31
INSTALLER LEVEL PROGRAMMING
The following table refers to programming locations
265 through 307.
ITEM VALID RANGE
Output Condition See next page for complete descriptions
0 = Not Used 22 = Armed and Exit Time Expired
1 = Fire Bell Output Trigger
2 = Reserved
3 = Fire Alarm
23 = Exit Time
24 = Entry Time
25 = Pre-Alarm Warning Time
4 = Fire Supervisory
5 = Reserved
6 = Fire Trouble
7 = Duress
8 = Low/No Battery
9 = Failed to Comm
10 = Telco Line Fault
11 = Telco Line Seized
26 = Annunciation
27 = Auto-Arm Warning
28 = Closing Ringback
29 = Trouble
30 = Audible Trouble
31 = Chime
32 = Universal Output
33 = Listen-In Module
12 = Ground Start
13 = Burglar Alarm
14 = Holdup Alarm
15 = Auxiliary Alarm
16 = Other Bell Output Trigger
17 = Violation
18 = Ready
19 = Armed AWAY
20 = Armed STAY
21 = Armed NIGHT
34 = Lamp Trigger
35 = Key 4 Output
36 = Key 5 Output
37 = Key 6 Output
38 = RF Annunciator
39 = Access by Keypad
40 = Quick Access by Keypad
101 - 130 = Zone (1 to 30) Violated
201 - 230 = Zone (1 to 30) In Alarm or Secure Watch
Areas of Operation (for Output Conditions 13 - 38)
1 = Area 1
2 = Area 2
3 = Both
[add up selections]
(for Output Conditions 39 & 40)
1 = Control Station 1
2 = Control Station 2
4 = Control Station 3
8 = Control Station 4
16 = Control Station 5
32 = Control Station 6
If the Output Condition is “Ready”, “Armed AWAY”,
“Armed STAY”, “Armed NIGHT”, “Armed & Exit
Time Expired”, “Exit Time”, “Entry Time”, “Annunciation”, “Key 4 Output”, “Key 5 Output”, or “Key
6 Output”, then the Areas of Operation should be limited to a single area.
32
INSTALLER LEVEL PROGRAMMING
Bell Output Activation
The Bell Output is assignable to a combination of areas and may activate due to an alarm condition in any of the areas. A Fire Alarm from a Fire or Verified
Fire zone or the ‘A’ Key will always activate the Bell
Output. A Burglar Alarm, a Burglar Tamper, a Holdup
Alarm, the ‘B’ Key, an Auxiliary Alarm, or the ‘C’ Key may activate the Bell Output.
Each alarm type is programmable for its Bell Output operation. (See Installer Level Programming - Global System Options Description). If more than one alarm type is active at the same time, the Bell Output will annunciate the highest priority alarm. The priority order is Fire, Auxiliary, Burglar, and Holdup.
If any of the Bell Output’s areas have Closing
Ringback Annunciation set to “Ringback Output,
Keypads, and Bell Output”, the Bell Output will emit a two (2) second ringback tone. (See Installer Level
Programming - Area Data Description).
To prevent accidents, the Bell Test on AWAY arm and the Ringback Bell are disabled while the duress output is active.
Programmable Output Activation
The programmable outputs will be activated according to their Output Condition listed in the following table. The output will go ON STEADY for the following conditions unless otherwise specified in the table below.
CONDITION
Fire Bell Output Trigger
Fire Alarm
Fire Supervisory
Fire Trouble
Duress
Panel Low/No Battery
Failed to Comm
Telco Line Fault
Telco Line Seized
Ground Start
Burglar Alarm
Holdup Alarm
Auxiliary Alarm
Other Bell Output Trigger
Violation
Ready
Armed AWAY
Armed STAY
Armed NIGHT
Armed & Exit Time Expired
Exit Time
OUTPUT BECOMES ACTIVE WHEN:
Activates according to cadence when a Fire or Verified Fire zone or an ‘A’ Key is in alarm as described above.
A Fire, Verified Fire or Water Flow zone or an ‘A’ Key is in alarm.
A zone defined as Fire Supervisory is in alarm.
A Fire or Verified Fire zone is in Trouble.
A Duress code has been used. To turn off, press the CLEAR key for 3 seconds.
A Panel Low/No Battery trouble condition occurs.
A Failed to Comm trouble condition occurs.
A Telco Line Fault trouble condition occurs.
The system seizes the telephone line for an RPM connection or prior to making a call to the Central
Station.
A Telco ground start circuit is triggered for one second.
A Burglar or a Burglar Tamper defined zone is in alarm.
A Holdup zone or an ‘B’ Key is in alarm.
An Auxiliary zone or an ‘C’ Key is in alarm.
Activates according to cadence for an Auxiliary, Burglar or Holdup Alarm as described above.
A Fire, Fire Supervisory, Water Flow, Burglar, Auxiliary, Visible Holdup or Burglar Tamper is in alarm.
The area is ready to arm.
The area has been armed in the AWAY mode.
The area has been armed in the STAY mode.
The area has been armed in the NIGHT mode.
The area has been armed in any way and the exit time has expired.
The exit time starts in its area due to an AWAY, STAY, or NIGHT arm. The output will go ON STEADY until the last ten seconds, then it will PULSE for the last ten seconds. When the Exit Time expires, it will go ON STEADY for two seconds.
33
INSTALLER LEVEL PROGRAMMING
Entry Time
Pre-Alarm Warning Time
Annunciation
Auto Arm Warning
Closing Ringback
Trouble
Audible Trouble
Chime
Universal
Listen-In
Lamp Trigger
The entry time starts in its area. The output will stay ON STEADY until the last ten seconds of entry time. During the last ten seconds of entry time, it will PULSE.
Any of its areas are in Pre-Alarm Warning Time. The output will PULSE when any of its areas are in
Pre-Alarm Warning Time.
The Annunciation output operates like a combination of the Exit Time, Entry Time, and Pre-Alarm
Warning Time outputs. When the exit time starts in its area due to an AWAY, STAY, or NIGHT arm, the output will go ON STEADY until the last ten seconds. During the last ten seconds, it will PULSE and when the exit time expires, it will go ON STEADY for two seconds. When the entry time starts in its area, the output will go ON STEADY until the last ten seconds of entry time. During the last ten seconds, it will PULSE. When in Pre-Alarm Warning Time, the output will PULSE.
The timer activates for 3 seconds for each minute of the ten minutes left before Auto-Arming occurs. It will also activate at one minute and two minutes until before an Exit Arm occurs.
A Closing Report due to an AWAY arm from a Control Station or keyswitch has been successfully transmitted to the Central Station.
A System Trouble condition is present. (See Operating the System - Trouble Conditions).
A System Trouble condition is present and has not been Silenced.
A Disarmed Chime Always Burglar zone in any of its areas is violated, a Disarmed Perimeter (Arm on
STAY & Arm on NIGHT) Burglar zone in any of its areas is violated and that area has Chime Enabled.
A Universal or Universal Logged zone is violated. (See Inst. Level Prog. - Prog. Notes, Note 16).
An alarm event is reported to the Central Station from one of the output’s areas. (See Inst. Level
Prog. - Prog. Notes, Note 11).
Any of its areas are in exit time, entry time and five minutes after entry time. The Output will go ON
STEADY when its areas are in entry time and will stay ON STEADY until five minutes after entry time expires or five minutes after disarm (whichever is shorter). (See Inst. Level Prog. - Prog. Notes, Note 17).
Key 4 Output
Key 5 Output
Key 6 Output
RF Annunciator
Access by Keypad
ENTER + Key #4 is pressed on a keypad primary to its area. May be used to toggle an output ON/
OFF.
ENTER + Key #5 is pressed on a keypad primary to its area. May be used to toggle an output ON/
OFF.
ENTER + Key #6 is pressed on a keypad primary to its area. May be used to toggle an output ON/
OFF.
Activates when an RF Keyfob is used in one of the output‘s areas. The output will pulse once for an
RF Keyfob disarm, twice for a successful RF Keyfob arm, and three times for a failed RF Keyfob arm.
Any of its Control Stations have an Access timer that is running or ON. (See Inst. Level Prog. - Prog.
Notes, Note 18).
Quick Access By Keypad Any of its Control Stations have a Quick Access timer that is running or ON. (See Inst. Level Prog. -
Prog. Notes, Note 18).
The zone is violated Zone Violated
Zone in Alarm or Secure Watch The zone goes into alarm. For a Burglar zone, it will deactivate when the alarm is silenced. For Fire,
Holdup, Auxiliary, Burglar Tamper, Verified Fire, and Fire Supervisory zones, it will deactivate when the zone restores after the alarm has been silenced. For Water Flow zones, it will deactivate when the zone restores. The zone goes into Secure Watch Trouble until the condition restores (See Inst.
Level Prog. - Prog. Notes, Note 10).
34
INSTALLER LEVEL PROGRAMMING
Global System Options Description
Global System Options Default Table
Fire Bell 1 Cutoff Time (min)
Fire Bell 2 Cutoff Time (min)
Burglar Cutoff Time (min)
Holdup Cutoff Time (min)
Aux Cutoff Time (min)
Universal Output Time (sec)
Delay Before Dial (sec)
Loc
TIME
Default
[308]
[309]
[310]
[311]
[312]
[313]
[314]
0
0
10
10
10
0
0
Fire Delay Before Dial (sec)
AC Failure Delay (min)
Secure Watch Time (hrs)
Reserved
Fire Bell
System Attributes
Passcode Attempts
Loc
TIME
Default
[315]
[316]
[317]
[318]
[319]
[320]
[321]
0
30
24
0
H-20
H-30
8
The following table refers to programming locations
308 through 321:
ITEM
Fire 1 Cutoff Time
Fire 2 Cutoff Time
Burglar Cutoff Time
Holdup Cutoff Time
Auxiliary Cutoff Time
Universal Output Time
VALID RANGE
0 = No Cutoff,
1 to 255 minutes
0 = No Cutoff,
1 to 255 minutes
0 = No Cutoff,
1 to 255 minutes
0 = No Cutoff,
1 to 255 minutes
0 = No Cutoff,
1 to 255 minutes
0 = Toggle ON,
1 to 255 seconds
Delay Before Dial 0 to 255 seconds
Fire Delay Before Dial
AC Trouble Delay
Secure Watch Time
Fire Bell
0 to 255 seconds
0 to 255 minutes
0 - 42 hours
00 to 30
(see Fire Bell Table)
DESCRIPTION
Determines the time in minutes for Bell Output or Fire Bell 1
Output and Fire Alarm signaling device.
Determines the time in minutes for Fire Bell 2 Output.
Determines the time in minutes for Bell Output or Other Bell
Output and Burglar Alarm signaling device.
Determines the time in minutes for Bell Output or Other Bell
Output and Holdup Alarm signaling device.
Determines the time in minutes for Bell Output or Other Bell
Output and Auxiliary Alarm signaling device.
Controls the timer for output programmed as Universal. Activated from Universal or Universal Logged zones. (See Inst. Level
Prog. - Prog. Notes, Note 16).
Time in seconds that a user has after a Burglar, Holdup or Auxiliary Alarm from a zone has occurred to silence the alarm with a disarm and abort the alarm event. (See Inst. Level Prog. - Prog.
Notes, Note 12).
Time in seconds that a user has after a Fire Alarm from a zone has occurred to silence the alarm and abort the alarm event.
(See Inst. Level Prog. - Prog. Notes, Note 13).
Determines the time that AC power must be down until the condition is reported to the Central Station. Time is in minutes and if the time set is an odd number, it will be silent; if the time set is an even number, it will be audible at the keypad.
Time in hours during which there is no activity before a Secure
Watch event is logged to be reported. (See Inst. Level Prog. -
Prog. Notes, Note 10).
The first digit defines the cadence of the Bell during a Fire Alarm.
The second digit is reserved.
35
INSTALLER LEVEL PROGRAMMING
ITEM
System Attributes
VALID RANGE
00 to FF
(see the System
Attribute Table.)
Passcode Entry Lockout 0 = No Lock,
1 to 15 attempts
DESCRIPTION
• Burglar Bell (Steady/Pulsed) - determines the operation of the
Bell Output or Other Bell Output during a Burglar alarm.
• Holdup Bell (Steady/Pulsed) - determines the operation of the
Bell Output or Other Bell Output during a Holdup alarm.
• Auxiliary Bell (Steady/Pulsed) - determines the operation of the
Bell Output or Other Bell Output during an Auxiliary alarm.
• Bell Test on Arm - if enabled, then the Bell Output or Other
Bell Output for an area will be activated for two seconds when that area is armed in the AWAY mode.
• Log Alarm Abort Events - if enabled, Abort Alarm events are posted in the Event Log. (See Inst. Level Prog.- Prog.
Notes, Notes 12 & 13).
• Log Access Events - if enabled, the “Keypad Access
Activated” events will be posted in the Event Log. These events are not reportable to the Central Station.
• Print Access Only R/T - if enabled with a printer connected, then only “Keypad Access Activated” events will be printed.
This does not affect the Event Log print command.
Sets the number of failed passcode entry attempts allowed before a 50 second lockout for a particular Control Station.
Fire Bell Table
FIRST DIGIT
0 = Steady
1 = Pulsed (March Time)
2 = Temporal
3 = Calif March Time
NOTE
Alarm Bell operations only affect the Bell Outputs. They do not affect the associated Alarm Indicator outputs.
System Attribute Table
ENTER FOR:
FIRST DIGIT
All Features Below Disabled
Log Alarm Abort Events
Log Access Events
Print Access Only Real Time
•
0 1 2 3 4 5 6 7 8 9 A B C D E F
•
•
• •
• •
• •
•
• • • •
•
• •
• •
• •
•
• • • •
SECOND DIGIT
Burglar Bell Steady
Burglar Bell Pulsed
Holdup Bell Steady
•
• •
•
•
•
•
• •
•
•
•
•
• •
•
•
•
•
• •
•
•
•
Holdup Bell Pulsed
Aux Bell Steady
Aux Bell Pulsed
• • •
• •
•
•
• • • •
•
• • •
•
•
• •
•
Bell Test on Arm
• • • • •
• •
• •
• • •
If the First Digit entered is ‘1’, it must be entered as ‘01’. A = 10; B = 11; C = 12; D = 13; E = 14; F = 15
36
INSTALLER LEVEL PROGRAMMING
Communicator Data Description
Communicator Data Default Table
Phone Line
Enable Skip Test
Power-up Comm Test
Disable Call Waiting
Comm Test Time of Day (hr:min)
Days Between Comm Tests
Time Between Calls (sec)
Trans Formats
Loc
[322]
[323]
[324]
[325]
[326: 327]
[328]
[329]
[330]
The following table refers to programming locations
322 through 337:
ITEM VALID RANGE
Phone Line 0 to 30
(see Phone Line Table)
Default
H-10
0
0
0
00:00
0
5
H-33
Enable Skip Test
Power-up Comm Test
Disable Call Waiting
Comm Test Time of Day
0 = No
1 = Yes
0 = No
1 = Yes
0 = No
1 = Yes
00:00 to 23:59 HH:MM
Days Between Comm Tests 0 = Disable, 1 to 255 days
Time Between Calls
Trans Formats
Dialer Type
CS1 Dial Attempts
CS2 Dial Attempts
Pager Dial Attempts
Pager Delay Time
On-Hook Time
& Off-Hook Time
0 to 255 seconds
00 to 44
(see Trans Formats Table)
00 to 20
(see Dialer Types Table)
1 to 15 attempts
1 to 15 attempts
1 to 15 attempts
0 to 255 seconds
1 to 15 seconds
Dialer Type
CS1 Dial Attempts
CS2 Dial Attempts
Pager Dial Attempts
Pager Delay Time (sec)
On-Hook Time (sec)
Off-Hook Time (sec)
Loc
[331]
[332]
[333]
[334]
[335]
[336]
[337]
Default
H-10
5
5
1
15
5
3
DESCRIPTION
First digit is used to enable the phone line for digital communicator event reporting and to enable monitoring of the phone line.
The second digit is reserved. If the phone line is disconnected, turning off the monitoring of the line will clear the PHONE LINE FAIL trouble condition.
Allows the auto comm test to be skipped if any signal has been transmitted to the Central Station since the last auto comm test.
Causes a communicator test to be initiated immediately upon system power up. Does not affect days between tests counter.
If enabled, the system will automatically dial “*70D” (or “1170D” if pulse dialing) prior to dialing a telephone number. This will temporarily disable the Call Waiting beeps during a phone call.
Sets the hour and minute in military format for the auto communicator test.
Sets the time intervals in days for the auto communicator test. A setting of 0 disables Automatic Comm Test Reporting. Days until next comm test may be manually adjusted by Control Station. (See
Installer Level Programming - Days Until Next Comm Test).
Time in seconds between a failed dial attempt to a Central Station and the next dial attempt.
First digit defines the transmission format used when the communicator dials the phone number for Central Station 1. Second digit defines the transmission format used when the communicator dials the phone number for Central Station 2. (See Inst. Level Prog.
- Prog. Notes, Note 14).
First digit defines the type of dialing used on the phone line. Second digit is reserved.
Maximum number of dial attempts when the communicator dials the phone number for Central Station 1.
Maximum number of dial attempts when the communicator dials the phone number for Central Station 2.
Total number of dial attempts when the communicator dials a Pager phone number. All attempts will be used.
Time in seconds that the communicator waits after dialing before blindly sending a 6-digit pager message.
Before the communicator dials a phone number, it seizes the phone line and goes off-hook for two seconds. It will then go back onhook for the On-Hook Time to disconnect an existing phone connection. The communicator will then go back off-hook for the Off-
Hook Time to acquire dial tone before dialing.
37
INSTALLER LEVEL PROGRAMMING
Phone Line Table
0 = Disabled
1 = Enabled
FIRST DIGIT
2 = Enabled with Line Monitor
3 = Enabled with Silent Line Monitor
Dialer Types Table
Transmission Formats Table
FIRST & SECOND DIGITS
0 = Pulsed 20 Baud - Non Extended 3 = Contact ID
1 = Pulsed 20 Baud - Non Extended 4 = Non-Telco Contact ID
2 = Pulsed 40 Baud - Extended
0 = US Rotary
1 = Touchtone ®
2 = Foreign Rotary
FIRST DIGIT
North American Standard (60/40) make/break ratio pulses.
Industry standard DTMF tones. Touchtone is a trademark of AT&T.
67/33 make break ratio pulses, typical of foreign countries.
Receiver Compatibility Table
RECEIVERS
Ademco 685
FBI CP220
Osborne-Hoffman (Quick Alert)
Radionics 6000
Radionics 6500
Silent Knight 9000
MLR-2DG
TRANSMISSION FORMAT
3/1, 4/2, Contact ID
3/1, 4/2, Contact ID
3/1, 4/2, Contact ID
3/1
3/1, 4/2
3/1, 4/2
3/1, 4/2, Contact ID
TRANSMISSION SPEEDS
(Pulse Reporting Only)
20B
20B - 40B
20B - 40B
20B - 40B
20B - 40B
20B - 40B
20B - 40B
All receivers listed functioned with the listed formats at time of testing. Modifications or programming changes may affect receiver operation. Consult manufacturer of specific receiver for setup and operation.
Communication Numbers Description
Event reporting assignments for each telephone number are programmed under the Installer Level Programming - Area Event Reporting section. The assignment
Communication Number Default Table
Central Station 1 Phone Number
Central Station 2 Phone Number
Area 1 Pager Phone Number
Area 2 Pager Phone Number
RPM/2 Pro Phone Number*
Area 1 Pager Header Message
Area 2 Pager Header Message
* Available for future use.
38 of telephone dialing options and reporting formats are programmed under the Installer Level Programming -
Communicator Data Description section.
Loc
[338 - 357]
[358 - 377]
[378 - 397]
[398 - 417]
[418 - 437]
[438 - 453]
[454 - 469]
Default
all F’s all F’s all F’s all F’s all F’s all F’s all F’s
INSTALLER LEVEL PROGRAMMING
Dialed Digits Allowed
All five phone numbers allow up to 20 hex digits.
The two Pager Header Messages allow up to 16 hex digits. See also Installer Level Programming - Programming Account Codes and Telephone Number
Digits.
0 - 9
A
B
C
D, E
F
Numbers from 0 to 9 dial the appropriate
Touchtone® or pulse digit.
Same as 0.
Programming a B into any digit position causes the communicator to produce a
Touchtone® * tone. Useful for unique applications such as voice mail, cellular, or paging applications.
Programming a C into any digit position causes the communicator to produce a
Touchtone® # tone.
Programming a D or E into any digit position causes a three second pause during dialing.
An ‘F’ may be programmed after the last digit of a number to signify end of dialing. An ‘F’ entered as the first digit of a number disables that number.
Pager Telephone Numbers
When an event is sent to a pager, the event’s Area
Pager Phone Number is dialed. System events are sent to the Area 1 Pager Phone Number. The communicator then waits the Pager Delay Time (see I.L.P.
Communicator Data Descr.) before blindly sending a pager message. The pager message may consist of up to 16 digits from the appropriate Pager Header
Message followed by a two digit code from the Pager
Event Table. Or, if the Pager Header Message is not needed, put an ‘F’ in its first digit and the appropriate four digit account code is used in its place. The Pager
Event Table is also available on a wallet card.
Only one message is sent per phone call and the call is made for the number of Pager Dial Attempts specified. There is no feedback from the pager, so pager events do not affect the failed to communicate condition.
NOTE
The paging network setup for your area determines if your pager will work with a pager telephone number.
21
22
23
24
25
26
31
32
33
Pager Event Table
2-DIGIT
CODE
15
16
17
18
11
12
13
14
EVENT DESCRIPTION
Fire Alarm
Supervisory Alarm
Burglar Alarm
Holdup Alarm
Duress
Auxiliary Alarm
Critical Condition Monitor
Exit Alarm
Zone Trouble
Testing (Fire Zone)
Zone Bypassed
Unsuccessful Attempt to Access via Keypad
System Trouble
AC Power Failure
Alarm Restore
Zone Trouble Restore
Zone Unbypassed
39
2-DIGIT
CODE
35
36
37
EVENT DESCRIPTION
System Trouble Restore
AC Power Restore
Central Station Comm Restore
41
42
43
44
45
46
51
52
61
62
63
64
65
66
Arm
Auto Arm Failed/Canceled
Auto Arm Delayed
Recent Closing
Disarm
Burglar Alarm Canceled
Latchkey Supervision
User On Premises
Comm Test
Comm Test (Not Normal)
Begin Installer Programming, Installer On Premise
End Installer/Remote Programming, Installer Off Premise
Remote Programming Failure
Call Home (Panic Key)
INSTALLER LEVEL PROGRAMMING
Event Reporting Description
Event Reporting Default Table
SYSTEM
Tel 1 Account No (4 Hex Digits)
Tel 2 Account No (4 Hex digits)
Fire Phone No.
System Events Phone No.
System Troubles Phone No.
Burglar Phone No.
Hold-up Phone No.
Auxiliary Phone No.
CCM Phone No.
Zone Trouble/Restore Phone No.
Zone Bypass/Restore Phone No.
Open/Close Phone No.
Supervision Phone No.
Loc
[470 - 473]
[474 - 477]
Default
0000
0000
[494]
[495]
[496]
3
0
3
Loc
AREA 1
Default
[478 - 481]
[482 - 485]
0000
0000
[497]
[498]
[499]
[500]
[501]
[502]
[503]
[504]
0
0
0
0
3
3
3
3
Loc
AREA 2
Default
[486 - 489]
[490 - 493]
0000
0000
[505]
[506]
[507]
[508]
[509]
[510]
[511]
[512]
0
0
0
0
3
3
3
3
40
INSTALLER LEVEL PROGRAMMING
The following table refers to programming locations
470 through 512:
ITEM
Telephone 1 Account No.
VALID RANGE
4 Hex Digits
Telephone 2 Account No.
4 Hex Digits
Fire Phone No.
Note: These events are reported using System account codes only.
System Events Phone No.
Note: These events are reported using System account codes only.
System Troubles Phone No.
Note: These events are reported using System account codes only.
Burglar Phone No.
0 to 11
(See Phone Directors Table)
0 to 11
(See Phone Directors Table)
0 to 11
(See Phone Directors Table)
0 to 11
(See Phone Directors Table)
Hold-up Phone No.
Auxiliary Phone No.
Critical Condition Monitor
(CCM) Phone No.
Zone Trouble/Restore
Phone No.
Zone Bypass/Restore
Phone No.
Open/Close Phone No.
Supervision Phone No.
0 to 11
(See Phone Directors Table)
0 to 11
(See Phone Directors Table)
0 to 11
(See Phone Directors Table)
0 to 11
(See Phone Directors Table)
0 to 11
(See Phone Directors Table)
0 to 11
(See Phone Directors Table)
0 to 11
(See Phone Directors Table)
DESCRIPTION
Account number used when dialing CS1 Phone Number or Pager.
(See Inst. Level Prog. - Prog. Notes, Note 14).
Account number used when dialing CS2 Phone Number.
(See Inst. Level Prog. - Prog. Notes, Note 14).
Directs which telephone number(s) to report Fire Alarms, Fire
Supervisories, and Restorals.
Directs which telephone number(s) to report system events.
Includes Keypad Lockout, Auto Comm Test, Begin & End Installer Local Programming, End Remote Programming, Remote
Programming Denied & Aborted.
Directs which telephone number(s) to report system events. Includes Keypad Missing & Restoral, AC Failure & Restoral, Panel Low/
No Battery & Restoral, Bell Faults & Restoral, Comm Restoral,
Memory Error, Phone Line Faults & Restoral, RF Jamming, RF Channel Clear and RF Keyfob Low Battery.
Directs which telephone number(s) to report Burglar Alarms,
Burglar Tamper, Exit Alarm, Recent Closing, Burglar Alarm Canceled, and Restorals.
Directs which telephone number(s) to report Holdup Alarms,
Duress, and Restorals.
Directs which telephone number(s) to report Auxiliary Alarms and Restorals.
Directs which telephone number(s) to report Critical Condition
Monitoring events and Restorals.
Directs which telephone number(s) to report Zone Troubles and
Restorals.
Directs which telephone number(s) to report Zone Bypasses and
Restorals.
Directs which telephone number(s) to report Openings, Closings, Auto Arm Fail, Auto Arm Aborted, and Closing Extended.
Directs which telephone number(s) to report Latch Key Supervision, User on Premises, Secure Watch, and Secure Watch Restore.
Phone Directors Table
0 = Do Not Report
1 = CS1 Phone Only
2 = CS2 Phone Only
3 = CS1 Phone (CS2 Phone on Failure)
4 = CS2 Phone (CS1 Phone on Failure)
5 = CS1 Phone and CS2 Phone
6 = Pager Only
7 = CS1 Phone and Pager
8 = CS2 Phone and Pager
9 = CS1 Phone (CS2 Phone on Failure) and Pager
10 = CS2 Phone (CS1 Phone on Failure) and Pager
11 = CS1 Phone, CS2 Phone and Pager
41
INSTALLER LEVEL PROGRAMMING
Zone Report Codes Description
The Zone Report Codes utilize programming locations 513 through 632. Each Zone has an alarm, restore, bypass and trouble code. The restore may be an alarm, trouble, or bypass restoral. A Zone
Trouble may result from one of the following conditions:
• Wiring problem
• Secure Watch Trouble
• No Response from Zone Expander
• Fire Trouble
(Fire zone bypassed or Fire zone in Walk Test)
• Smoke Trouble
• RF Point Not Reporting
• RF Sensor Tamper
• RF Point Low Battery
These events will be posted and displayed differently in the Event Log. If one of these events is reported using a Pulsed format, then the standard Zone
Trouble report code will be used. If one of these events is reported using Contact ID then a more descriptive report code will be used.
Each report code requires a two digit entry. The first digit sets the primary event code and the second digit sets the extended code. (See Installer Level
Programming - Programming Report Codes). If a transmission format other than a Pulsed format is used, it is only necessary to program a value other than zero into either digit to enable that event to be reported, the correct transmitted data is automatically sent.
42
INSTALLER LEVEL PROGRAMMING
Zone 17
Zone 18
Zone 19
Zone 20
Zone 21
Zone 22
Zone 23
Zone 24
Zone 25
Zone 26
Zone 27
Zone 28
Zone 29
Zone 30
Zone 09
Zone 10
Zone 11
Zone 12
Zone 13
Zone 14
Zone 15
Zone 16
Zone 01
Zone 02
Zone 03
Zone 04
Zone 05
Zone 06
Zone 07
Zone 08
Zone Report Codes Default Table
Loc
ALARM
Default
[609]
[613]
[617]
[621]
[625]
[629]
[577]
[581]
[585]
[589]
[593]
[597]
[601]
[605]
[545]
[549]
[553]
[557]
[561]
[565]
[569]
[573]
[513]
[517]
[521]
[525]
[529]
[533]
[537]
[541]
H-6A
H-6B
H-6C
H-6D
H-11
H-12
H-62
H-63
H-64
H-65
H-66
H-67
H-68
H-69
H-39
H-3A
H-3B
H-3C
H-3D
H-3E
H-3F
H-61
H-31
H-32
H-33
H-34
H-35
H-36
H-37
H-38
Loc
RESTORE
Default
[610]
[614]
[618]
[622]
[626]
[630]
[578]
[582]
[586]
[590]
[594]
[598]
[602]
[606]
[546]
[550]
[554]
[558]
[562]
[566]
[570]
[574]
[514]
[518]
[522]
[526]
[530]
[534]
[538]
[542]
H-E6
H-E6
H-E6
H-E6
H-E1
H-E1
H-E6
H-E6
H-E6
H-E6
H-E6
H-E6
H-E6
H-E6
H-E3
H-E3
H-E3
H-E3
H-E3
H-E3
H-E3
H-E6
H-E3
H-E3
H-E3
H-E3
H-E3
H-E3
H-E3
H-E3
Loc
BYPASS
Default
[611]
[615]
[619]
[623]
[627]
[631]
[579]
[583]
[587]
[591]
[595]
[599]
[603]
[607]
[547]
[551]
[555]
[559]
[563]
[567]
[571]
[575]
[515]
[519]
[523]
[527]
[531]
[535]
[539]
[543]
H-AB
H-AB
H-AB
H-AB
H-AB
H-AB
H-AB
H-AB
H-AB
H-AB
H-AB
H-AB
H-AB
H-AB
H-AB
H-AB
H-AB
H-AB
H-AB
H-AB
H-AB
H-AB
H-AB
H-AB
H-AB
H-AB
H-AB
H-AB
H-AB
H-AB
Loc
TROUBLE
Default
[612]
[616]
[620]
[624]
[628]
[632]
[580]
[584]
[588]
[592]
[596]
[600]
[604]
[608]
[548]
[552]
[556]
[560]
[564]
[568]
[572]
[576]
[516]
[520]
[524]
[528]
[532]
[536]
[540]
[544]
H-F6
H-F6
H-F6
H-F6
H-F1
H-F1
H-F6
H-F6
H-F6
H-F6
H-F6
H-F6
H-F6
H-F6
H-F3
H-F3
H-F3
H-F3
H-F3
H-F3
H-F3
H-F6
H-F3
H-F3
H-F3
H-F3
H-F3
H-F3
H-F3
H-F3
43
INSTALLER LEVEL PROGRAMMING
User Report Codes Description
The User Report Codes utilize programming locations 633 through 732. This data block is used to program the opening and closing reports for each user code.
Each report code requires a two digit entry. The first digit sets the primary event code and the second digit sets the extended code. (See Installer Level
Programming - Programming Report Codes). If a transmission format other than a Pulsed format is used, it is only necessary to program a value other
User 09
User 10
User 11
User 12
User 13
User 14
User 15
User 16
User 01
User 02
User 03
User 04
User 05
User 06
User 07
User 08
User 17
User 18
User 19
User 20
User 21
User 22
User 23
User 24
User 25
User Report Code Default Table
CLOSE
Loc Default
[633] H-C1
[635] H-C2
[637] H-C3
[639] H-C4
[641] H-C5
[643] H-C6
[645] H-C7
[647] H-C8
[649] H-C9
[651] H-CA
[653] H-CB
[655] H-CC
[657] H-CD
[659] H-CE
[661] H-CF
[663] H-CF
[665] H-CF
[667] H-CF
[669] H-CF
[671] H-CF
[673] H-CF
[675] H-CF
[677] H-CF
[679] H-CF
[681] H-CF
OPEN
Loc Default
[634] H-B1
[636] H-B2
[638] H-B3
[640] H-B4
[642] H-B5
[644] H-B6
[646] H-B7
[648] H-B8
[650] H-B9
[652] H-BA
[654] H-BB
[656] H-BC
[658] H-BD
[660] H-BE
[662] H-BF
[664] H-BF
[666] H-BF
[668] H-BF
[670] H-BF
[672] H-BF
[674] H-BF
[676] H-BF
[678] H-BF
[680] H-BF
[682] H-BF
User 34
User 35
User 36
User 37
User 38
User 39
User 40
User 41
User 26
User 27
User 28
User 29
User 30
User 31
User 32
User 33
User 42
User 43
User 44
User 45
User 46
User 47
User 48
User 49
User 50 than zero into either digit to enable that event to be reported, the correct transmitted data is automatically sent.
The open and close report code is assigned to the user, not the area. Some users may be assigned to arm and disarm multiple areas. Any user with the authority to arm and disarm multiple areas has the same opening and closing report codes. However, the Central Station can differentiate between areas by the account code transmitted.
CLOSE
Loc Default
[699]
[701]
[703]
[705]
[707]
[709]
[711]
[713]
[683]
[685]
[687]
[689]
[691]
[693]
[695]
[697]
[715]
[717]
[719]
[721]
[723]
[725]
[727]
[729]
[731]
H-CF
H-CF
H-CF
H-CF
H-CF
H-CF
H-CF
H-CF
H-CF
H-CF
H-CF
H-CF
H-CF
H-CF
H-CF
H-CF
H-CF
H-CF
H-CF
H-CF
H-CF
H-CF
H-CF
H-CF
H-CF
OPEN
Loc Default
[684] H-BF
[686] H-BF
[688] H-BF
[690] H-BF
[692] H-BF
[694] H-BF
[696] H-BF
[698] H-BF
[700] H-BF
[702] H-BF
[704] H-BF
[706] H-BF
[708] H-BF
[710] H-BF
[712] H-BF
[714] H-BF
[716] H-BF
[718] H-BF
[720] H-BF
[722] H-BF
[724] H-BF
[726] H-BF
[728] H-BF
[730] H-BF
[732] H-BF
44
INSTALLER LEVEL PROGRAMMING
System Report Codes Description
Each report code requires a two digit entry. The first digit sets the primary event code and the second digit sets the extended code. (See Installer Level
Programming - Programming Report Codes). If the transmission format is anything other than a Pulsed
System Event Report Codes Default Table
‘A’ Key Report Code
‘B’ Key Report Code
‘C’ Key Report Code
Duress Code
Keypad Lockout Code
Burg Cancel Report Code
Quick Arm Report Code
Auto-Arm Code
Auto-Arm Failed Code
Keyswitch Closing Code
Keyswitch Opening Code
Installer/RPM Closing Code
Installer/RPM Opening Code
Closing Extended Code
Exit Alarm Code
Recent Closing Code
Latch Key Supervision Code
User on Premises Code
Comm Test Not Norm Code
Comm Test Report Code
AC Fail Report Code
Loc
[741]
[742]
[743]
[744]
[745]
[746]
[747]
[748]
[733]
[734]
[735]
[736]
[737]
[738]
[739]
[740]
[749]
[750]
[751]
[752]
[753]
Default
H-00
H-00
H-00
H-00
H-00
H-00
H-00
H-00
H-00
H-00
H-00
H-00
H-FA
H-19
H-29
H-49
H-99
H-00
H-00
H-00
H-00 format, it is only necessary to program a value other than zero into either digit to enable that event to be reported, the correct transmitted data is automatically sent.
AC Restore Report Code
Low/No Battery Report Code
Battery Restore Code
Bell Fault Report Code
Bell Restore Report Code
Telco Fault Report Code
Telco Restore Report Code
Reserved
Reserved
Comm Restore Report Code
Memory Error Report Code
Local Program Begin Code
Local Program End Code
RPM End Report Code
RPM Denied Report Code
RPM Abort Report Code
Missing Keypad Code
Restore Keypad Code
RF Jamming Code
RF Channel Clear Code
RF Keyfob Low Battery Code
Default
H-00
H-00
H-00
H-00
H-00
H-00
H-00
H-00
H-00
H-00
H-00
H-00
H-00
H-EA
H-F9
H-E9
H-00
H-00
H-00
H-00
H-00
Loc
[762]
[763]
[764]
[765]
[766]
[767]
[768]
[769]
[754]
[755]
[756]
[757]
[758]
[759]
[760]
[761]
[770]
[771]
[772]
[773]
[774]
The following table refers to programming locations
733 through 774:
ITEM
‘A’ Key Report Code
‘B’ Key Report Code
‘C’ Key Report Code
Duress Code
Keypad Lockout Code
Burg Cancel Report Code
Quick Arm Report Code
Auto-Arming Code
Auto-Arm Failed Code
VALID RANGE
00 to FF
00 to FF
00 to FF
00 to FF
00 to FF
00 to FF
00 to FF
00 to FF
00 to FF
DESCRIPTION
Code sent for alarms activated by pressing the Fire panic key.
Code sent for alarms activated by pressing the Police panic key.
Code sent for alarms activated by pressing the Medical panic key.
Code sent for a duress (Authority Level 13) code arm or disarm.
Code sent when a Control Station is locked out due to failed passcode attempts.
Code sent when an authorized user resets a burglar alarm after reporting and before the Burglar Bell Cutoff timer expires.
Code sent when an area is armed using Two-Button or Double Press Arming.
Code sent when armed by scheduled program or Exit Arm.
Code sent when a scheduled arming is aborted or could not be completed.
45
INSTALLER LEVEL PROGRAMMING
Keyswitch Closing Code
Keyswitch Opening Code
Installer/RPM Closing Code
Installer/RPM Opening Code
Closing Extended Code
Exit Alarm Code
Recent Closing Code
Latch Key Supervision Code
User on Premises Code
Comm Test Not Norm Code
00 to FF
00 to FF
00 to FF
00 to FF
00 to FF
00 to FF
00 to FF
00 to FF
00 to FF
00 to FF
Comm Test Report Code
AC Fail Report Code
AC Restore Report Code
Low Battery Report Code
Battery Restore Code
Bell Fault Report Code
Bell Restore Report Code
Telco Fault Report Code
Telco Restore Report Code
Comm Restore Report Code
Memory Error Report Code
Local Prog Begin Code
Local Prog End Code
RPM End Report Code
RPM Denied Report Code
RPM Abort Report Code
Missing Keypad Code
Restore Keypad Code
RF Jamming Report Code
RF Channel Clear Code
RF Keyfob Low Battery Code
00 to FF
00 to FF
00 to FF
00 to FF
00 to FF
00 to FF
00 to FF
00 to FF
00 to FF
00 to FF
00 to FF
00 to FF
00 to FF
00 to FF
00 to FF
00 to FF
00 to FF
00 to FF
00 to FF
00 to FF
00 to FF
Code sent when an area is armed by keyswitch zone.
Code sent when an area is disarmed by keyswitch zone.
Code sent when an area is armed by RPM or the installer at a Control Station.
Code sent when an area is disarmed by RPM or the installer at a Control Station.
Code sent when the scheduled closing time is extended.
Code sent in addition to a burglar alarm event if the alarm occurs when the exit time expires.
Code sent in addition to a burglar alarm event if the alarm occurs within two minutes after exit time expires.
Code sent when the Latch Key code is not entered during the programmed time window.
Code sent when the User on Premises (Authority Level 12) passcode is entered to disarm the system or perform the access operation.
Code sent at the comm test time-of-day in place of the comm test report when a trouble condition is present. If this report code is set to 00, a normal comm test event is transmitted.
Code sent at the comm test time-of-day when no trouble conditions are present. Transmitted at power-up, if Test On Power-Up is enabled. (See Inst. Level Prog.- Communication Data
Description). Implies proper operation of the communicator and the telephone line.
Code sent when the control has lost the primary AC input. The delay time before this report is transmitted is located in Installer Level Programming - Global System
Options Description.
Code sent when the AC primary power has been restored.
Code sent when the control detects a low battery voltage reading of 11.3 VDC or less.
Code sent when the low battery condition has been restored.
Code sent when the control panel detects a Bell Fault. Contact ID will distinguish between Bell 1 and Bell 2 faults.
Code sent when a Bell Fault trouble restores. Contact ID will distinguish between Bell 1 and Bell 2 restores.
Code sent when the control panel detects a Telco Fault. Contact ID will distinguish between Phone Line and Non-Telco faults.
Code sent when a Telco Fault trouble restores. Contact ID will distinguish between
Phone Line and Non-Telco restores.
When the control is unsuccessful in reporting an event, the fail to communicate
(local trouble) displays. If a subsequent report of any type is successful, the control also reports this code.
Code sent when the internal memory check finds an unauthorized change in the value of one or more of the programming options.
Code sent when a program function map is initiated at the control site.
Code sent after programming mode is terminated at the installation site. This occurs
255 seconds after exiting programming mode or by holding the CLEAR key for three seconds.
Code sent when an RPM session has been completed normally.
Code sent when an unauthorized RPM session is attempted (i.e.: improper ID code or access device).
Code sent when an RPM session is aborted. If an alarm event requiring a report to the Central Station occurs during an RPM session, the control may abort the session to report the event.
Code sent when a supervised Control Station is removed or fails to respond to system polling.
Code sent when a missing Control Station is restored to the data bus.
Code sent when an RF Gateway detects an RF Jamming condition.
Code sent when an RF Gateway detects an RF Jamming condition has cleared.
Code sent when an RF Gateway detects a low battery condition on one of its Fobs.
46
INSTALLER LEVEL PROGRAMMING
Area Schedules Description
Automatic Arming
If automatic arming is enabled, the control produces a warning signal at the appropriate Control Station(s) once every minute beginning ten minutes prior to the event. During this warning, the same Control
Station(s) may display a visual indication of the impending action and the amount of time remaining.
This allows the user ample warning to exit or override the impending action. Auto Arming time may be extended by one hour during each ten minute warning period (but not past midnight) using the
Delay Auto Arming function. The user can also abort the scheduled arming for that day through User Level programming. (See the appropriate User Guide).
Auto Arming arms the control in the AWAY, STAY, or
NIGHT mode with normal exit time.
Area Schedules Default Table
Scheduled Arm Mode
Scheduled Arm Days
Arm Time Sun (hr:min)
Arm Time Mon (hr:min)
Arm Time Tues (hr:min)
Arm Time Wed (hr:min)
Arm Time Thurs (hr:min)
Arm Time Fri (hr:min)
Arm Time Sat (hr:min)
Latch Key User ID
Latch Key Days
Latch Key Window (min)
Latch Time Sun (hr:min)
Latch Time Mon (hr:min)
Latch Time Tues (hr:min)
Latch Time Wed (hr:min)
Latch Time Thurs (hr:min)
Latch Time Fri (hr:min)
Latch Time Sat (hr:min)
Loc
[775]
[776]
[777:778]
[779:780]
[781:782]
[783:784]
[785:786]
[787:788]
[789:790]
[791]
[792]
[793]
[794:795]
[796:797]
[798:799]
[800:801]
[802:803]
[804:805]
[806:807]
AREA 1
Default
00:00
0
H-00
0
00:00
00:00
00:00
00:00
0
H-00
00:00
00:00
00:00
00:00
00:00
00:00
00:00
00:00
00:00
Latch Key Schedules
A Latch Key User ID is used to determine which user passcode must be entered on selected Latch Key
Days. The user passcode must be entered within a time window. If the user passcode is not entered during the Time Window, a Latch Key Supervision event will be posted in the Event Log to be reported.
For example, if Monday is a Latch Key Day and the
Latch Key Time for Monday is 14:30 with a thirty minute
Time Window and the Latch Key User ID is not entered between 14:00 and 15:00 hours, then a Latch
Key Supervision event will be posted at 15:00 hours.
NOTE
The Latch Key Time Window cannot cross over the Midnight boundary. During the Time Window, the Control Station will chime once a minute until the user passcode is entered or the Time
Window has expired, whichever comes first.
Loc
[808]
[809]
[810:811]
[812:813]
[814:815]
[816:817]
[818:819]
[820:821]
[822:823]
[824]
[825]
[826]
[827:828]
[829:830]
[831:832]
[833:834]
[835:836]
[837:838]
[839:840]
AREA 2
Default
00:00
0
H-00
0
00:00
00:00
00:00
00:00
0
H-00
00:00
00:00
00:00
00:00
00:00
00:00
00:00
00:00
00:00
47
INSTALLER LEVEL PROGRAMMING
The following table refers to programming locations
775 through 840:
ITEM VALID RANGE DESCRIPTION
Scheduled Arming Mode
Scheduled Arming Days
Sunday Arming Time
Monday Arming Time
Tuesday Arming Time
Wednesday Arming Time
Thursday Arming Time
Friday Arming Time
Saturday Arming Time
Latch Key User ID
Latch Key Days
Latch Key Time Window
Sunday Latch Key Time
Monday Latch Key Time
Tuesday Latch Key Time
Wednesday Latch Key Time 00:00 to 23:59
Thursday Latch Key Time
Friday Latch Key Time
Saturday Latch Key Time
0 = AWAY, 1 = STAY, 2 = NIGHT Determines the Auto Arm mode.
00 to FF
(see the table below for a complete description of each value’s activation)
Selects the days of the week the system automatically arms.
00:00 to 23:59 The time for Auto Arming on Sunday.
00:00 to 23:59
00:00 to 23:59
00:00 to 23:59
00:00 to 23:59
The time for Auto Arming on Monday.
The time for Auto Arming on Tuesday.
The time for Auto Arming on Wednesday.
The time for Auto Arming on Thursday.
00:00 to 23:59
00:00 to 23:59
0 = disable, User 1 to 50
00 to FF (see Scheduled Arming and Latch Key Days Table.)
0 to 255 minutes
00:00 to 23:59
00:00 to 23:59
00:00 to 23:59
00:00 to 23:59
00:00 to 23:59
00:00 to 23:59
The time for Auto Arming on Friday.
The time for Auto Arming on Saturday.
Determines the user passcode that has Latch Key Supervision.
Selects the days of the week that Latch Key Supervision is performed.
Time in minutes (+/-) the Latch Key User Code may be entered.
The time, (+/-) the Time Window, the Latch Key user passcode must be entered on Sunday.
The time, (+/-) the Time Window, the Latch Key user passcode must be entered on Monday.
The time, (+/-) the Time Window, the Latch Key user passcode must be entered on Tuesday.
The time, (+/-) the Time Window, the Latch Key user passcode must be entered on Wednesday.
The time, (+/-) the Time Window, the Latch Key user passcode must be entered on Thursday.
The time, (+/-) the Time Window, the Latch Key user passcode must be entered on Friday.
The time, (+/-) the Time Window, the Latch Key user passcode must be entered on Saturday.
Scheduled Arming and Latch Key Days Table
ENTER FOR:
FIRST DIGIT
All Days Below Disabled
Thursday
Friday
Saturday
•
0 1 2 3 4 5 6 7 8 9 A B C D E F
•
•
• •
• •
• •
•
• • • •
•
• •
• •
• •
•
•
• • •
SECOND DIGIT
All Days Below Disabled
•
Sunday
Monday
Tuesday
Wednesday
•
•
•
•
•
•
•
•
• •
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
If the First Digit entered is ‘1’, it must be entered as ‘01’. A = 10; B = 11; C = 12; D = 13; E = 14; F = 15
•
•
•
•
48
INSTALLER LEVEL PROGRAMMING
Programming Options
This section deals with the attributes of the Remote
Programming Manager Software. Before programming the specific functions, it is important to understand the following:
Abort: During a remote programming session, the control is fully functional and can detect and annunciate alarms locally. The control aborts a session with RPM/2 Pro to report alarm events.
Datalock: As a provision of anti-takeover, the control does not permit local programming of the account numbers and telephone numbers, or the Restore Factory Defaults option to operate when an agency code has been established and programmed by the RPM/2 Pro software. Other installer programming changes are still allowed. When the Datalock
(agency code) is set, the Control Station emits an error tone if any attempt is made to change an account number or a phone number or to default the control.
Programming Options Default Table
Installer Passcode
Call 2 Timer (sec)
Auto Answer Ring Count
Enable RPM
Enable Power Up Program
Lockout Local Program
Loc
[841 - 844]
[845]
[846]
[847]
[848]
[849]
Default
9632
0
5
1
0
0
The following table refers to programming locations
841 through 849:
ITEM
Installer Passcode
VALID RANGE
0000 to 9999
2nd Call Timer
Auto Answer Ring Count
Enable RPM
0 - 255 seconds
0 - 15 rings
DESCRIPTION
The installer passcode is the only passcode that may program the entire
Function Map. See Installer Level Programming - User Data Description for a description of the other functions that may be performed.
Time in seconds for the answering machine bypass time window. This allows the remote programmer to bypass an answering machine by making two calls to the premises. The first call must ring three times or less and not be answered. The answering machine bypass time window starts ten seconds after the last ring of the first call. If the first ring of the second call occurs within the answering machine bypass time window, the panel answers the second call on the first ring. Remote Programming must be enabled and
Auto-Answer Ring count must be non-zero.
Sets the number of rings that must occur before the panel automatically answers the telephone for operation with RPM/2 Pro. A ring count of 0 disables automatic answering, but manual connection may still be used. If
Remote Programming is not enabled, then the auto-answer ring count is ignored and the panel never answers.
Enables operation of the control with the RPM/2 Pro package.
Enable Power Up Program
0 = No
1 = Yes
0 = No
1 = Yes
Lockout Local Program 0 = No
1 = Yes
A quick way to enter program mode upon power up. Pressing the ”9“ key and entering “9999” within the first 60 seconds after power up enters the control into Installer Level Programming mode. Consider disabling this feature for anti-takeover.
This is provided for anti-takeover protection. If it is enabled, the installer passcode is limited as noted in Installer Level Programming - User
Data Description. A user may still be able to perform user level programming and RPM/2 Pro will be fully operational. Do not enable this unless an
RPM/2 Pro account has been established for the control.
49
INSTALLER LEVEL PROGRAMMING
Programming Notes
Note 1: Restarting Exit Time
If an exit time is counting down from an AWAY arming, the exit time may be automatically restarted once to reduce false alarms.
The exit time will be restarted if a Perimeter (arm in
STAY mode and arm in NIGHT mode) Burglar zone is violated anytime during the last ten seconds of exit time.
If the exit time is not due to an Exit Arm or a Scheduled Arming, then the exit time will be restarted if it expires and a Perimeter (Arm in STAY mode and
Arm in NIGHT mode) Burglar zone has not been violated during the exit time (i.e.: nobody went out the door).
Note 1A: Entry Delay Times
The Entry Delay Times (Entry Delay 1 and Entry Delay 2) of an area work together to provide a more secure Entry Delay Time. For example, Entry Delay
1 may be programmed as 4 minutes and Entry Delay 2 may be programmed as 1 minute. If Entry Delay 1 (4 min.) is started and counts down to 2 minutes remaining when an armed Delay 2 zone is violated, then the Entry Delay Time is reduced to the more secure Entry Delay 2 time (1 minute remaining). However, if the Entry Delay Time counts down below the Entry Delay 2 Time (i.e. to 30 seconds remaining), then no adjustment is made. Entry Delay Time is only decreased, it is never increased.
Note 3: Exit Arm
An Exit Arm is intended to automatically arm an area ten minutes after the premises are vacated. An Exit
Arm will only be attempted when it is enabled for an area and the area is disarmed and not in alarm.
The end user can disable the Exit Arm feature on a day-to-day basis (see the appropriate User Guide).
If a Disable Exit Arming is performed, the Exit Arm will be disabled until midnight.
When a Delay Burglar zone restores from a violation, the area’s Exit Arm timer is started at ten minutes. During this time, the Control Station may display a visual indication of the impending action and the amount of time remaining. An audible warning signal will occur at two minutes until arming and at one minute until arming. When any Burglar zone is violated, the area’s Exit Arm timer is halted. If a Delay zone restores from a violation while the timer is running, the timer is restarted at ten minutes. If an
Instant or Follower Burglar zone restores from a violation, the timer is halted.
If the timer expires (i.e.: ten minutes of no Burglar zone activity following a Delay zone restoration), then the system attempts to arm the area in the
AWAY mode. If Force-Arming is enabled, then a
Force-Arm may occur if needed. If the arming is successful, then Exit time is started and an Auto-Arm event is logged to be reported. If the arming cannot be completed, then nothing will happen.
Note 4: Force-Arming
If Force-Arming is enabled for an area, then an arming from a keyswitch zone, an Exit Arming or a
Scheduled Arming will be Force-Armed if necessary.
Note 2: Entry Time versus Pre-Alarm Warning
Time
Assuming Exit, Entry and Pre-Alarm Warning Times are inactive, a violation of an armed Burglar zone will cause the following actions depending on the area’s arm level and the type of Burglar zone:
Note 5: LED Control Stations
The Secondary Area setting is ignored for LED Control Stations since they cannot provide area infor-
Instant Burglar
Delay Burglar
Follower Burglar
AWAY
Instant Alarm
STAY STAY INSTANT NIGHT NIGHT INSTANT
Pre-Alarm Warning Pre-Alarm Warning Pre-Alarm Warning Pre-Alarm Warning
Time Time Time Time
Entry Time Entry Time Instant Entry Time Instant
Pre-Alarm Warning Pre-Alarm Warning Pre-Alarm Warning Pre-Alarm Warning Pre-Alarm Warning
Time Time Time Time Time
50
INSTALLER LEVEL PROGRAMMING
mation and prompts. Therefore, LED Control Stations cannot have a Secondary Area.
Note 6: Verifying or Self-Verifying Burglar Zones
If an armed Verifying Burglar zone is violated, then a forty second Verification Timer is started. If the timer expires and the zone that started it is still in violation, then the zone’s violation is verified. If another armed
Burglar zone is violated while the timer is still running, then that violation verifies the first zone’s violation.
If an armed Self-Verifying Burglar zone is violated, then a forty second Verification Timer is started. If the Timer expires and the zone is still in violation, then the zone’s violation is verified. If another armed
Burglar zone is violated while the Timer is still running, then that violation verifies the first zone’s violation. If the same armed Burglar zone is violated a second time while the Timer is still running, then the zone’s violation is verified.
If the area is armed such that a violation from the zone would normally cause an instant alarm:
• when the zone is first violated, nothing happens.
• when the violation is verified, an instant alarm occurs.
• if the Verification Timer expires without the violation being verified, then nothing happens.
If the area is armed such that a violation from the zone would normally cause an Entry Time or Pre-
Alarm Warning Time Delay:
• when the zone is first violated, the Delay Timer is started.
• if the violation is verified while the Delay Timer is still running, then the Delay Timer continues as normal.
• if the Verification Timer expires while the Delay
Timer is still running and the violation has not been verified, then the time continues. If the
Delay Timer expires and no zones are violated from the Delay Time, then nothing happens.
• if the Delay timer expires before the Verification timer expires and the violation has not been verified, then nothing will happen until either the violation is verified or the Verification Timer expires.
• if the violation is verified after the Delay Timer has expired, then an instant alarm occurs.
• if the Verification Timer expires after the Delay
51
Timer has expired without the violation being verified, then nothing happens.
Common Area Burglar zones cannot be programmed as verifying or self-verifying, but they can verify a verifying or self-verifying zone from Area 1 or Area 2 (see
Operating the System - Introduction).
Note 7: Sentry Test Burglar Zones
If a Burglar zone has Sentry Test enabled, then each time the zone is disarmed, it must be tested before it can be armed again. A test consists of violating the zone from a restored state and then restoring it again.
If the zone has not been tested, then it appears as a faulted zone, making its area not ready to arm. An untested zone cannot be armed. If the zone is bypassable, then it may be bypassed to get around the testing. Force-Arming should not be enabled on systems with Sentry Test Burglar Zones.
Note 8: Zone Activation of Bell Output and
Keypad Sounders
The Bell Output on Alarm attribute determines whether the Bell Output for the zone’s area activates due to an alarm from the zone. It does not affect the activation of any other programmable outputs, including an associated Alarm output.
This attribute is only used if the Zone Type is Burglar, Holdup, Auxiliary or Burglar Tamper; otherwise, it is ignored. The Bell Output activates on all alarms from Fire and Verified Fire zones and from an ‘A’ key. It never activates from the other Zone Types.
The Keypad Sounder on Alarm attribute determines whether the Control Station sounders activate due to an alarm from the zone. It does not affect the activation of any programmable outputs. This attribute is only used if the Zone Type is Burglar,
Holdup or Auxiliary; otherwise, it is ignored. Keypad sounders activate on all alarms from Fire and
Verified Fire zones and from an ‘A’ key, as well as from Burglar Tamper and Fire Supervisory zones.
They never activate from the other Zone Types.
If a Holdup zone is programmed with neither Bell
Output on Alarm nor Keypad Sounder on Alarm, then an alarm from the zone will be invisible on the
Control Stations.
INSTALLER LEVEL PROGRAMMING
Note 9: Bypassable Zones - Fire Trouble
Condition
All zones may be programmed as Bypassable. If a
Fire, Verified Fire, or Fire Supervisory zone is bypassable and is bypassed, a Fire Trouble condition occurs and is reported. The condition remains until the zone is unbypassed.
Note 10: Secure Watch
The Secure Watch attribute may only be used with
Burglar, Critical Condition Monitor, Non-Alarm, Universal, and Universal Logged zones. It is ignored for all other zone types.
If a Burglar zone has Secure Watch enabled, then the Secure Watch only applies when the zone is disarmed and not bypassed. Whenever the zone is violated, disarmed or unbypassed, the zone’s Secure
Watch timer is reset to the programmed time. If that timer expires and the zone is disarmed and not bypassed, then a Secure Watch Trouble event is posted for the zone to be reported. The trouble condition is not displayed on the keypad and it does not prevent the area from being armed. A Secure
Watch Trouble Restore event is posted for the zone to be reported if the zone is then either violated, armed, or bypassed.
If a Critical Condition Monitor, Non-Alarm, Universal, or Universal Logged zone has Secure Watch enabled, then the Secure Watch only applies when the zone is not bypassed. When the zone is violated or unbypassed, the zone’s Secure Watch timer is reset to the programmed time. If that timer expires and the zone is not bypassed, then a Secure Watch
Trouble event is posted for the zone to be reported.
The trouble condition is not displayed on the keypad. A Secure Watch Trouble restore event is posted for the zone to be reported if the zone is either violated or bypassed.
While a zone has a Secure Watch Trouble condition, its corresponding Secure Watch signaling device
(programmable output) will stay ON steady.
Note 11: The Listen-In Module
The Listen-In Module must be wired to the telephone lines in series with and behind the control panel.
The Listen-In Module must be connected to the panel
52 as follows. A Line-Seized indicator line must be connected from the ACTIVE output on the Listen-In
Module to an assigned Listen-In Module zone on the panel. A Listen-In output line must be connected from an assigned output on the panel to the ACTI-
VATE input on the Listen-In Module.
The zone programmed as the Listen-In Module zone is area independent and is used by the panel to determine whether or not the Listen-In Module has seized the telephone line and has the microphone(s) active. The output programmed as the Listen-In
Output may be assigned to any combination of areas. It is used by the panel to signal the Listen-In
Module for activation.
The Listen-In Module may be configured in one of two modes, Instant Seize mode or Answer mode.
If the Listen-In Module is configured in Instant Seize mode, then when it is first signaled from the panel, it instantly seizes the phone line and signals the panel through the Listen-In Module zone but does not turn on the microphones. When the panel releases the connection to the Central Station and deactivates the Listen-In Output, the Listen-In Module already has the line seized and assumes the connection.
If the Listen-In Module is configured in Answer mode, then after the panel has signaled it by activating and later deactivating the Listen-In Output, the Listen-In
Module starts its incoming call timer. The incoming call timer starts when the Listen-In Output is deactivated and runs for five minutes. If a call comes in while the timer is running, then the Listen-In Module answers the call on the first ring. At that time, it signals the panel through the Listen-In Module zone that it has seized the line.
When the control panel detects the Line-Seized signal from the Listen-In Module zone, it temporarily silences all alarm tones at the Control Stations and the Bell Outputs, although the alarm output timers continue. When the Listen-In Module releases the phone line, it removes the Line-Seized signal to the panel. When the control panel detects the Line-
Seized signal has been removed, it no longer silences alarm tones at the Control Stations and Bell Outputs. The Bell Outputs are reactivated if they have not timed-out.
Also, when the panel detects the Line-Seized signal from the Listen-In Module zone and gets an event
(any event) to report to the Central Station, the panel
INSTALLER LEVEL PROGRAMMING
signals the Listen-In operator by momentarily seizing the phone line and producing a tone. This interrupts the Listen-In Module connection for about one second but it does not hang-up the phone line.
The panel also starts a two minute timer. It will not try to call out to the Central Station until either the
Line-Seized signal from the Listen-In zone is removed or the two minute timer expires, whichever comes first. If the timer expires before the Line-Seized signal is removed, the panel seizes the line to dial out to the Central Station, disconnecting and hanging up the Listen-In Module’s connection.
If an alarm is silenced through a Control Station during a Listen-In session, it has no impact on the Listen-In operation.
NOTE
If a Holdup Alarm event is reported to the Central Station, it is the Listen-In operator’s responsibility to NOT activate the speakers on the Listen-In Module.
Note 12: Delay Before Dial Time
The Delay Before Dial Time is used as the time that a user has after a Burglar, Holdup, or Auxiliary Alarm from a zone has occurred to silence the alarm with a disarm and abort the Alarm event.
If the Delay Before Dial Time is not zero and the alarm is silenced before the Delay Before Dial Time expires, then no Alarm events are posted to be reported. If this occurs and Log Alarm Aborted Events is enabled, then
Alarm Aborted events are posted for each zone that went into alarm, but they are not reported.
If the Delay Before Dial Time is zero or if the Delay
Before Dial Time expires before the alarm is silenced with a disarm, then the Alarm events are posted to be reported. If the alarm is a Burglar Alarm and the alarm is silenced with a disarm before the Burglar
Bell Cutoff Timer expires, then a “Cancel Alarm” event is logged to be reported.
If an alarm in a Control Station’s Primary or Secondary area is in Delay Before Dial Time, then when the OFF CANCEL key is pressed on the Control Station, all alarms in the Control Station’s Primary and
Secondary areas are muted until the Delay Before
Dial Time expires. While an alarm is muted, the
53
Control Stations do not produce the alarm tone for the alarm and the Bell Output(s) are silent. The muting of an alarm does not affect the operation of programmed outputs. If the Delay Before Dial Time expires without the alarm being silenced, then the
Control Stations resume the alarm tone and the Bell
Output(s) re-activate. The alarm cut-off timer(s) continue to count while the alarm is muted.
Note 13: Fire Delay Before Dial
The Fire Delay Before Dial Time is used as the time that a user has after a Fire Alarm from a zone has occurred to silence the alarm and abort the Alarm event.
If the Fire Delay Before Dial Time is not zero and the alarm is silenced before the Fire Delay Before
Dial Time expires, then no Alarm events are posted to be reported. If this occurs and Log Alarm Abort
Events is enabled, the Alarm Aborted events are posted for each zone that went into alarm, but they are not reported. If a Fire Alarm is silenced before the Fire Delay Before Dial Time expires, the user has 255 seconds to reset the smoke detectors, otherwise a smoke reset will automatically occur when
255 seconds elapses.
If the Fire Delay Before Dial Time is zero or if Fire Delay
Before Dial Time expires before Fire Alarm is silenced, then the Alarm events are posted to be reported.
If a Fire Alarm is in Fire Delay Before Dial Time then when the Off Cancel key is pressed from a keypad, all alarms in the keypads Primary and Secondary area are muted until the Fire Delay Before Dial
Time expires. While an alarm is muted, the Control
Stations do not produce the alarm tone for the alarm and the Bell Output(s) are silent. The muting of an alarm does not affect the operation of programmed outputs. If the Fire Delay Before Dial Time expires without the alarm being silenced, then the Control
Stations resume the alarm tone and the Bell
Output(s) re-activate. The alarm cut-off timer(s) continue to count while the alarm is muted.
Fire Delay Before Dial Time does not apply to Fire
Alarms from Water Flow zones.
Note 14: Transmission Formats
If the Data Format is “Pulsed 20 Baud - Non-Extended”, then the number of digits in the account
INSTALLER LEVEL PROGRAMMING
code determines how events are reported. If the fourth digit of the account code is 0, then events are reported in the 3/1 Non-Extended format. If the fourth digit of the account code is not 0, then events are reported in the 4/1 Non-Extended format. Only the first digit of the report code is sent. If an account code digit or the first digit of the report code is 0, then that digit is transmitted as an ‘A’.
Each event is reported in two rounds for verification.
For the 3/1 Non-Extended format, the first three digits of the account code and the first digit of the report code are transmitted in a round. For the 4/1
Non-Extended format, all four digits of the account code and the first digit of the report code are transmitted in a round.
If the Data Format is “Pulsed 20 Baud - Extended” or “Pulsed 40 Baud - Extended”, then the number of digits in the account code must be four (4) digits.
Both digits of the report code are sent. If an account code digit or one of the report code digits is
0, then that digit is transmitted as an ‘A’. Each event is reported in two rounds for verification.
For the 4/2 Extended format, then all four digits of the account code and both digits of the report code are transmitted in a round.
If the Data Format is “Contact ID”, then all four digits of the account code are sent. The report code is only used to determine if the event is sent or not.
The reports are generated from a Contact ID report table. This is an Ademco developed format.
If the Data Format is “Non-Telco Contact ID”, then all four digits of the account code are sent. The report code is only used to determine if the event is sent or not. The reports are generated from a Contact ID report table. The report will be sent to an interface device over the data bus. The interface device will send an acknowledgment to the system upon successful transmission of an event. The associated Central Station telephone number will not be used, but its first digit must not be an ‘F’. If the interface device responds back with a transmission failure or if the interface device “loses” the event, the system will view it as a failed dial attempt. If the interface device is not responding on the data bus, a “Non-Telco Failure” condition will be posted and the system will not try to report through the interface. This may cause a “Comm Failure” condition to occur or the event may be reported using another phone number.
If the Pager option is used, up to 16 digits of the
Pager Header Message and a 2-digit Pager Event
Message are sent. (If the Pager Header Message is not used, a 4-digit Account Code and a 2-digit Pager
Event Message are sent). The telephone number will be dialed for the number of dial attempts programmed and the pager message will be blindly sent each time. There will be no feedback and, therefore, no failed to communicate.
The Pager option is perfect for the parent who works late and wants to know if their child arrived home safely. When the child disarms the system, the parent is paged. Since arming/disarming reports are programmed for each user, the system can be programmed to only page when the child’s user passcode is used or when a passcode with the User on Premises authority level is used. The pager option can also be used with the Latch Key Supervision report to page the parent when the child does not come home when expected.
Note 15: Powering Up While Armed
If either area is armed when the panel powers up, violations from all the burglar zones are ignored for three minutes. This allows all armed PIRs to stabilize without causing false alarms.
Note 16: Universal Outputs
A Universal output may be assigned to any combination of areas and is controlled by the Universal timer or keypad in each of the areas. When a Universal or Universal Logged zone in an area is violated, the area’s Universal timer will begin a countdown. If the Universal Output Time is set to zero
(0), then the area’s Universal timer will turn ON. To turn it OFF, use the ENTER + Key #2 secondary function.
If the Universal Output Time is not set to zero (0), then the ENTER + Key #2 secondary function will override the Universal Output timer. For example, if the timer is running when the function is performed, then the output will be turned OFF and the timer will halt. A new zone activation will turn the output
ON and re-start the timer. If the timer is not run-
54
ning when the function is performed, then the function will turn the output ON and subsequent zone violations will be ignored until after the output is turned OFF by performing the function again.
A Universal output will go ON STEADY when any of its areas have a Universal timer that is either running or ON. If the Universal Output Time is 0, only one area should be used to control a Universal output.
Otherwise, an area will not be able to turn the output OFF if another area has turned it ON.
Note 17: Lamp Trigger Outputs
A Lamp Trigger output will change state (ON to OFF or OFF to ON) for the Control Station’s Primary area when the ENTER + Key #1 secondary function is performed. If the output is turned ON with the ENTER
+ Key #1 secondary function and then an arming occurs, the output will turn OFF when the Exit Time expires.
Note 18: Access and Quick Access Outputs
An Access output will be controlled by the Access operations (0 + passcode) performed on any of its
Control Stations or from RPM. A Quick Access output will be controlled by pressing ENTER + Key #3.
If a Control Station is used to toggle an Access or
Quick Access output between ON and OFF, then it should be the only Control Station controlling that output. Otherwise, you may not be able to turn the output OFF if another Control Station has turned it
ON.
INSTALLER LEVEL PROGRAMMING
55
CONTACT ID FORMATS
Digital Communicator Table For Contact ID
Formats
This section cross-references many of the reporting options and equivalent codes sent by Sentrol-manufactured controls when transmitting in the Contact
ID formats.
Simplified example of data sent in Contact ID format:
SSSS 18 Q XYZ AA CCC
SSSS = 4 decimal digit subscriber #
18 = Contact ID que for automation systems
Q = Event qualifier; 1 = new event or opening;
3 = new restore or closing; 6 = previously reported event
EVENT TYPE
‘A’ Key Fire Alarm
Zone Fire Alarm
Zone Fire Supervisory
Zone Burglar Alarm
Zone Burglar Tamper
‘B’ Key Holdup Alarm
Zone Holdup Alarm
Duress
‘C’ Key Auxiliary Alarm
Zone Auxiliary Alarm
Zone CCM Alarm
Zone Non-Alarm
Zone Fire Trouble
Zone Fire Test Mode Begin
Zone Burglar Trouble
Zone Holdup Trouble
Zone Auxiliary Trouble
Zone Other Trouble
Secure Watch Trouble
Zone No Response on Bus
RF Point Not Reporting
Smoke Trouble
RF Sensor Tamper
RF Point Low Battery
Zone Fire Bypass
Zone Burglar Bypass
Zone Holdup Bypass
Zone Auxiliary Bypass
Zone Other Bypass
Zone Fire Alarm Restore
CID CODE
1115
1110
1200
1130
1137
1120
1120
1121
1100
1100
1150
1163
1373
1604
1370
1370
1370
1370
1641
1333
1381
1380
1383
1384
1571
1573
1572
1572
1570
3110
56
XYZ = Event code (3 decimal digits)
AA = Area number (00 for system events)
CCC = Zone, sensor, or user # (3 decimal digits)
EVENT SOURCE
500 + Keypad (1 - 6)
Zone (1 - 30)
Zone (1 - 30)
Zone (1 - 28)
Zone (1 - 28)
500 + Keypad (1 - 6)
Zone (1 - 28)
User (1 - 50)
500 + Keypad (1 - 6)
Zone (1 - 28)
Zone (1 - 28)
Zone (1 - 28)
Zone (1 - 30)
Zone (1 - 30)
Zone (1 - 28)
Zone (1 - 28)
Zone (1 - 28)
Zone (1 - 28)
Zone (1 - 28)
Zone (13 - 29)
Zone (13 - 28)
Zone (13 - 30)
Zone (13 - 28)
Zone (13 - 28)
Zone (1 - 30)
Zone (1 - 28)
Zone (1 - 28)
Zone (1 - 28)
Zone (1 - 28)
Zone (1 - 30)
Zone Fire Supervisory Restore
Zone Burglar Alarm Restore
Zone Burglar Tamper Restore
Zone Holdup Alarm Restore
Zone Auxiliary Alarm Restore
Zone Critical Condition Monitor Alarm Restore
Zone Non-Alarm Restore
Zone Fire Trouble Restore
Zone Fire Test Mode End
Zone Burglar Trouble Restore
Zone Holdup Trouble Restore
Zone Auxiliary Trouble Restore
Zone Other Trouble Restore
Secure Watch Trouble Restore
Zone No Response Restore
RF Point Reporting
Smoke Trouble Restore
RF Sensor Tamper Restore
RF Point Low Battery Restore
Zone Fire Bypass Restore
Zone Burglar Bypass Restore
Zone Holdup Bypass Restore
Zone Auxiliary Bypass Restore
Zone Other Bypass Restore
User AWAY Arm from Keypad
User STAY or NIGHT Keypad Arm
Quick AWAY Arm from Keypad
Quick STAY or NIGHT Keypad Arm
Keyswitch Arm
Installer Arm
RPM/2 Pro Arm
Auto Arm
Auto Arm Failed
Auto Arm Aborted
Closing Extended
Exit Alarm
Recent Closing
User Disarm from Keypad
Keyswitch Disarm
Installer Disarm
RPM/2 Pro Disarm
Latch Key Supervision
User on Premises
Keypad Locked-out
Keypad Missing
Keypad Missing Restore
Burglar Alarm Canceled
Auto-Comm Test (Not Normal)
3200
3130
3137
3120
3100
3150
3163
3384
3571
3573
3572
3572
3570
3401
3456
3408
3408
3373
3604
3370
3370
3370
3370
3641
3333
3381
3380
3383
1374
3459
1401
1409
1400
1407
1642
1458
3409
3400
3407
3403
1455
3455
3405
1300
1330
3330
3406
1608
57
CONTACT ID FORMATS
Zone (1 - 30)
Zone (1 - 28)
Zone (1 - 28)
Zone (1 - 28)
Zone (1 - 28)
Zone (1 - 28)
Zone (1 - 28)
Zone (1 - 30)
Zone (1 - 30)
Zone (1 - 28)
Zone (1 - 28)
Zone (1 - 28)
Zone (1 - 28)
Zone (1 - 28)
Zone (13 - 29)
Zone (13 - 28)
Zone (13 - 30)
Zone (13 - 28)
Zone (13 - 28)
Zone (1 - 30)
Zone (1 - 28)
Zone (1 - 28)
Zone (1 - 28)
Zone (1 - 28)
User (1 - 50)
User (1 - 50)
No Data
No Data
Zone (1 - 28)
No Data
No Data
No Data
No Data
User (1 - 50)
User (1 - 50)
Zone (1 - 28)
User (1 - 50)
User (1 - 50)
Zone (1 - 28)
No Data
No Data
User (1 - 50)
User (1 - 50)
500 + Keypad (1 - 6)
500 + Keypad (1 - 6)
500 + Keypad (1 - 6)
User (1 - 50)
No Data
CONTACT ID FORMATS
Auto-Communicator Test
AC Failure
AC Restore
Panel Low/No Battery
Panel Battery Restore
Bell Fault
Bell Restore
Communication Restore
Memory Error
Begin Installer Local Program
End Installer Local Program
End Remote Programming
Remote Programming Denied
Remote Programming Aborted
RF Jamming
RF Channel Clear
RF Keyfob Low Battery
Phone Line Failure
Phone Line Restore
Non-Telco Failure
Non-Telco Restore
3354
1303
1627
1628
3412
1413
1412
1381
3381
1602
1301
3301
1302
3302
1321
3321
1384
1351
3351
1353
3353
No Data
No Data
No Data
No Data
No Data
No Data
No Data
No Data
No Data
No Data
No Data
No Data
No Data
No Data
No Data
No Data
User (1 - 50)
No Data
No Data
No Data
No Data
58
UL REQUIREMENTS
UL Programming Requirements
Underwriters Laboratories (UL)
Listing
This control is listed by Underwriters Laboratories
(UL) as follows:
APPLICATION
Household Burglary (Grade A)
Household Fire
Central Station Burglary (Grade C)
Central Station Burglary (Grade B)
Home Health Care Signaling Equipment
Local Burglary (Grade A)
Police Station Burglary Connection (Grade A)
LISTING
UL 1023
UL 985
UL 1610/1635
UL 1610/1635
UL 1637
UL 609
UL 365
UL has established certain requirements which pertain to the installation, use, and programming of this equipment. The local Authority Having Jurisdiction (AHJ) and/or UL may have other requirements which apply to the installation of this system that are not detailed in this manual. It is the responsibility of the installing dealer to check with the AHJ and/ or UL before installing this system. The following pages detail guidelines that must be followed in order to comply with the UL listings as stated above.
UL Notes In This Manual
• Key “0” (Access) - The control has not been investigated to UL 294 Access Control System requirements.
• Unsupervised Burglary Zones - UL does not permit the use of unsupervised zones.
UL Notes About Program
Functions
• Entrance Delay Time (1 and 2) - Maximum of
45 seconds.
• AWAY Exit Delay Time - Maximum of 60 seconds.
• Burglar Alarm Cutoff Time - Four minutes minimum for household BA/FA and 15 minutes for commercial burglar alarm and police station connected burglar alarm system.
• Fire Cutoff Time - Minimum of four (4) minutes.
59
• Communicator Enable - Local or police station connected burglar alarm installations: The communicator must be enabled.
• Days Between Comm. Tests - Commercial installations: automatic test performed every 24 hours.
• Time Between Dial Attempts - UL certified accounts: no more than 45 seconds between attempts.
• Dial Type - Will not be programmed for foreign pulse.
• Dial Attempts Before Shutdown - Five dial attempts minimum, ten dial attempts maximum.
• Arming/Disarming Reports - This function will be enabled by programming report codes.
• Low Battery Reporting - This function will be enabled by programming a report code for Grade
A Local Burglar, Grade A Police Connected, and
Grade B and C Central Station Burglar installations.
• Two Button/Double Press Arming - These functions will be disabled. Four digit passcodes will be used.
• Enable Force Arming - This function will be disabled.
• Enable Bypassing - This function will be disabled.
• Burglar Alarm Output - Will be programmed to
STEADY.
• Fire Alarm Output - Will be programmed to TEM-
PORAL.
• Burglar Loop Audible Lockout - This function will be disabled.
• Enable Bell Test Upon Arming - This function will be enabled for Grade A Local Central Station
Connected installations.
UL REQUIREMENTS
• Enable Keypad Sounder for BA Zones - The system will have an audible alarm output upon alarm.
• Auto-Arming - This function will be disabled.
• Listen-In Modules must not be used.
• Burglar zones will not be programmed as Verifying or Self-Verifying.
• Output Type can NOT be programmed as
Ground Start
• RF User Devices must be assigned to User
Passcodes 1 - 30.
UL Notes About Zone Planning
• Burglar Loops - Will be defined as Alarm on
Open/Alarm on Short.
• Fire, Holdup, and Auxiliary Emergency Zones -
Will not be defined as bypassable.
• Special Functions/Alarms - Burglar zones will have an audible output.
• Medical Emergency - At least one Control Station will be used as part of the system.
60
NOTES
Notes
______________________________________________________________________
______________________________________________________________________
______________________________________________________________________
______________________________________________________________________
______________________________________________________________________
______________________________________________________________________
______________________________________________________________________
______________________________________________________________________
______________________________________________________________________
______________________________________________________________________
______________________________________________________________________
______________________________________________________________________
______________________________________________________________________
______________________________________________________________________
______________________________________________________________________
______________________________________________________________________
61
NOTES
Notes
______________________________________________________________________
______________________________________________________________________
______________________________________________________________________
______________________________________________________________________
______________________________________________________________________
______________________________________________________________________
______________________________________________________________________
______________________________________________________________________
______________________________________________________________________
______________________________________________________________________
______________________________________________________________________
______________________________________________________________________
______________________________________________________________________
______________________________________________________________________
______________________________________________________________________
______________________________________________________________________
62
63
SENTROL
SENTROL CONTROLS GROUP
PO Box 2904, 1510 Tate Blvd. SE
Hickory, NC 28603
Tel.: 503.692.4052 Fax: 503.691.7566
U.S. & Canada: 800.547.2556
Technical Service: 800.800.2027
FaxBack: 800.483.2495
64
Sentrol reserves the right to change specifications without notice.
©1997 Sentrol
64812702D
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project