Netgear WNDR3700v4 QIG

Netgear WNDR3700v4 QIG
Installation Guide
N600 Wireless Dual Band Gigabit Router
Step 1:
Step 2:
Unplug the power
to turn off your modem.
Connect one end of the
yellow Ethernet cable
to your modem, and the
other end to the Internet
port on your router.
Package Contents
(not included)
Laptop or desktop
Step 5:
Connect your computer
to the router ( ).
Use another Ethernet cable to
establish a wired connection
as shown in this diagram.
Optionally, connect wirelessly
by using the preset wireless
security settings, located on
the bottom label.
Power On/Off
Power On/Off
Ethernet cable
Step 3:
Plug in the power to
turn on your modem.
N600 Wireless Router
Power adapter
Step 6:
N600 Wireless Router
Open a browser.
Step 4:
Wait approximately 2 minutes
until your modem turns on.
Connect the power adapter to the
router, then plug it into an outlet.
If your modem has
a battery backup,
first remove and reinsert
the battery before connecting
your modem to power.
Wait for the 2.4 GHz LED (
to light.
2.4 GHz
If none of the LEDs light, make sure
that the Power On/Off button is in the
on position (pushed in).
If the web page does not
display, close and re-open
the browser, then enter
in the address bar, or
check the “Troubleshooting”
section on the back of
this installation guide.
Preset Wireless Security
This product has a unique WiFi network name (SSID) and network key (password).
The default SSID and password are uniquely generated for every device (like a
serial number), to protect and maximize your wireless security. This information is on
the label on the bottom of the product.
NETGEAR recommends that you do not change the preset SSID or password. If you
do change the settings, the information on the bottom of the product does not apply.
Connect Wireless Devices to Your Router
Choose either the manual or Wi-Fi Protected Setup (WPS) method to add wireless
computers, and other devices to your wireless network.
The browser cannot display the web page.
• Make sure that the computer is connected to one of the four LAN Ethernet ports,
or wirelessly to the router.
• Make sure that the Wireless LED is lit.
• Close and reopen the browser to make sure that the browser does not cache the
previous page.
• Browse to
• If the computer is set to a static or fixed IP address (this setting is uncommon),
change it to obtain an IP address automatically from the router.
Manual Method
Open the software utility that manages your wireless connections on the
wireless device that you want to connect to your router (iPhone, laptop,
computer, gaming device). This utility scans for all wireless networks in your
2. Look for the preset NETGEAR wireless network name (SSID), and select it.
The SSID is on the product label on the bottom of the router.
Note: If you changed the name of your network during the setup process, look
for that network name.
Enter the preset password (or your custom password if you changed it), and
click Connect.
4. Repeat steps 1–3 to add other wireless devices.
Find the preset wireless settings on your router and record them here:
WiFi network name (SSID) ________________________________
WPS Method
If you change the preset wireless settings, record them here:
If your wireless device supports WPS (Wi-Fi Protected Setup)—NETGEAR calls
this method Push 'N' Connect—you might be prompted to press the WPS button on
the router instead of entering a password. If you are prompted to press the WPS
Wireless network name (SSID) _______________________________
Network key (password) _____________________________________
Network key (password) __________________________________
If necessary to retrieve or update your password, type in a web browser, and log in using the
default user name (admin) and password (password).
Press the WPS button
After installing your device, locate the serial number on the label of your product
and use it to register your product at You must register your
product before you can use NETGEAR telephone support. NETGEAR recommends
registering your product through the NETGEAR web site. Visit for product updates, additional documentation, and
For the free Live Parental Controls centralized Internet site filtering software for your
router, visit
For additional features, including traffic metering, ReadySHARE, and guest access,
log in to your router at
NETGEAR recommends that you use only the official NETGEAR support
Download the free Desktop
NETGEAR genie:
on the router.
Within 2 minutes, press the WPS button on the client device, or follow the
WPS instructions that came with your wireless device to complete the WPS
process. The device is then connected to your router.
3. Repeat this process to add other WPS wireless devices.
Note: WPS does not support WEP security. If you try to connect a WEP client
to your network using WPS, it does not work.
WiFi Connection
Router Settings
STATUS Connected
Click here
Network Map
Parental Controls
Number of devices 16
Click here
Click here
Automatically fix common network
problems and easily manage your
home network connections.
Select Wireless Settings to locate your wireless password.
For the complete EU Declaration of Conformity, visit
December 2012
NETGEAR,the NETGEAR logo, and Connect with Innovation are trademarks and/or registered trademarks of
NETGEAR, Inc.and/or its subsidiaries in the United States and/or other countries. Information is subject to
change without notice. Other brand and product names are trademarks or registered trademarks of their
respective holders. © by NETGEAR, Inc. All rights reserved.
Intended for indoor use only in all EU member states, EFTA states, and Switzerland
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF