advertisement
RMQ Series
• RMQ-230-3G • RMQ-230-SD • RMQ-230-A
• RMQ-200-3G • RMQ-200-SD • RMQ-200-A
• RMQ-170-3G • RMQ-170-SD • RMQ-170-A
Quad-Split, LCD, Multi-Viewer Audio/
Video Monitors
User Guide
Part Number 821097, Revision A
© 2013 Wohler Technologies, Inc. All rights reserved.
This publication is protected by federal copyright law. No part of this publication may be copied or distributed, stored in a retrieval system, or translated into any human or computer language in any form or by any means electronic, mechanical, manual, magnetic, or otherwise, or disclosed to third parties without the express written permission of Wohler Technologies.
Reproduction
Licensed users and authorized distributors of Wohler Technologies, Inc. products may copy this document for use with Wohler Technologies., Inc. products provided that the copyright notice above is included in all reproductions.
Customer Support
Wohler Technologies, Inc.
31055 Huntwood Avenue
Hayward, CA 94544 www.wohler.com
Phone: 510-870-0810
FAX: 510-870-0811
US Toll Free: 1-888-596-4537
(1-888-5-WOHLER)
Web: www.wohler.com
Sales: [email protected]
Support: [email protected]
Disclaimers
Even though Wohler Technologies, Inc. has tested its equipment and software, and reviewed the documentation, Wohler Technologies, Inc. makes no warranty or representation, either express or implied, with respect to software, documentation, their quality, performance, merchantability, or fitness for a particular purpose.
Wohler Technologies, Inc. reserves the right to change or improve our products at any time and without notice.
In no event will Wohler Technologies, Inc. be liable for direct, indirect, special, incidental, or consequential damages resulting from any defect in the hardware, software, or its documentation, even if advised of the possibility of such damages.
Some states do not allow the exclusion or limitation for incidental or consequential damages, so the above exclusion or limitation may not apply to you
.
Printing
This document is intended to be printed on a duplex printer, such that the copy appears on both sides of each page. This ensures that all new chapters start on a right-facing page.
This document looks best when printed on a color printer since some images may be indistinct when printed on a black and white printer.
Last Update
March 04, 2013 ii
821097: RMQ Series User Guide
© 2013 Wohler Technologies, Inc. All rights reserved.
RMQ Series
Introduction
Overview
The RMQ Series quad split, LCD video monitors are high-performance, professional LCD monitors that support advanced 10-bit digital processing technology and also 3D comb filter and de-interlace, accurate scaling engine, GAMMA correction and color temperature adjustment to achieve the best possible image display.
The RMQ Series supports 4-channel 3G/HD/SD-SDI/CVBS signal and a single HDMI signal input. They can simultaneously display four signal inputs, with three typical display modes including one full screen display, one big-with-three small screen displays and four uniform size screen displays.
Topics
Topics
Page
821097: RMQ Series User Guide
© 2013 Wohler Technologies, Inc. All rights reserved.
1
RMQ Series
Safety
Safety
Important Safety Instructions
IMPORTANT:
1.
Read, keep, and follow all of these instructions; heed all warnings.
2.
Do not use this equipment near water, rain or moisture.
3.
Use only a dry cloth to clean the equipment.
4.
Do not install near any heat source such as a radiator, heat register, amplifier, or stove.
5.
Do not attempt to plug the unit into a two-blade outlet (with only two prongs of equal width).
By design, these monitors will only plug into a three-prong outlet for your safety. If the plug does not fit into your outlet, contact an electrician to replace the obsolete outlet.
6.
Protect the power cord from being walked on or pinched, particularly at plug’s source on the equipment and at the socket.
7.
Use only the attachments/accessories specified by the manufacturer.
8.
Unplug the equipment during lightning storms or when unused for long periods of time.
9.
Use of a cart is neither recommended nor approved by Wohler.
10.
Refer all servicing to qualified service personnel. Servicing will be required under all of the following conditions:
• The equipment has been damaged in any way, such as when the power-supply cord or plug is damaged.
• Objects have fallen onto the equipment; or the equipment has been exposed to rain or moisture, or liquid has been spilled onto the equipment.
• The equipment does not operate normally.
• The equipment has been dropped.
2
821097: RMQ Series User Guide
© 2013 Wohler Technologies, Inc. All rights reserved.
RMQ Series
Installation Recommendations
Safety Symbols
WARNING: The symbol to the left warns of electric shock hazard inside the unit.
Disconnect the power cord before removing access panels when installing upgrades. Only qualified service personnel are to operate the equipment with covers removed, and are to exercise caution to avoid personal injury.
Installation Recommendations
Heat Dissipation
The ambient temperature around the unit should not exceed 40°
Celsius (104° Fahrenheit). Allow plenty of space around the unit for air circulation.
Mounting/Bracing
Stands for desktop mounting are provided. The fixed desktop stand resists tipping over. The adjustable stand may need bracing when raised to its higher positions.
Wall mounting kits (not provided) are available for semi-permanent installations. Ensure that the lock hardware will resist movement from mobile vehicles or seismic vibrations.
Connections and Cable Recommendations
We recommend that you limit the length of the cables that you use for feeding HD-SDI signals sources to the HD-SDI inputs of the RMQ
Series units and that you use a Belden 1694A cable (or equivalent). The
HD-SDI inputs ( IN1 and IN4 ) can be up to 150 meters (492 feet) in length for 1.5 Gbps (HD), more for 270 Mbps (SD) and less for 3Gbps.
821097: RMQ Series User Guide
© 2013 Wohler Technologies, Inc. All rights reserved.
3
RMQ Series
Unpacking and Installation
Note: HDMI 1.3 or 1.4 cable lengths of 2m (6 feet) are guaranteed to work well. Four meters (12 feet) lengths of high quality cable should work well enough, but is not guaranteed for all situations. Longer HDMI cables often degrade signal quality. Active extender transmitter/receiver pairs can be used to cover long distances.
Electrical Interference
Be careful to properly terminate/ground signals and avoid mismatched cable types and other similar causes of undesired reflections in digital signal systems. If severe enough, such reflections can result in corruption of the digital data stream. As with any audio equipment, maximum immunity from electrical interference requires the use of shielded cable. The internal circuitry ground is connected to the chassis.
Power
The unit comes with a standard 19VDC/4.7 A external power adapter and connects an A/C mains power source (65W, 100 to 240 VAC, 50/
60Hz) through the IEC connector provided on the power adapter.
When the mains plug or appliance coupler is used as the disconnect device, the disconnect device connection should remain accessible to be operable.
Unpacking and Installation
Contents
4
While unpacking the components, verify that none of the components are damaged.
Also verify that the box contains all of the following:
• Monitor
• Base
821097: RMQ Series User Guide
© 2013 Wohler Technologies, Inc. All rights reserved.
RMQ Series
Unpacking and Installation
Mounting
• Base board with screws
• Adapter (19V)
• Power cord
• User guide CDROM
• Warranty card
The RMQ Series monitor comes standard with two table top stands: one fixed and one adjustable.
Alternatively, you can order the rack mount kit separately.
Refer to Figure 1–1 on page 5 while installing the fixed base onto the
monitor. Refer to the instructions included with other mounts when used.
Figure 1–1 RMQ Fixed Base Installation
M4 Screws
Before After
821097: RMQ Series User Guide
© 2013 Wohler Technologies, Inc. All rights reserved.
5
RMQ Series
Features
1.
Install the base to the monitor.
2.
Place the monitor on a solid static-free surface.
3.
Connect the power cord to the rear panel of the monitor and to mains power.
4.
Connect the signal inputs to the rear panel.
5.
Press the Power switch (DC IN) on the rear panel of the monitor.
6
Features
The RMQ Series monitors provide the following features:
• 178° viewing angle
• Multi-format analog and digital audio signals
• Four of 5 input signals (4 x SDI/CVBS, 1 x HDMI)
• Adjustment of the parameters for each channel
• High-quality waveform or vector monitoring (for CH1 and CH3 in quad view)
• Embedded SDI or stereo analog audio through speakers or headphones
• Audio bar graph meters, up to sixteen
• Stereo analog audio line output of selected channel
• Area, safety, and center markers
• Closed captions for CVBS
• Pre-set or user-adjustable color temperature per channel
• Time code for SD-SDI in ANC-packet form
• Dynamic OSD/IMD tally
• HDMI output for a larger display
821097: RMQ Series User Guide
© 2013 Wohler Technologies, Inc. All rights reserved.
RMQ Series
Front Panel Features
Front Panel Features
The following feature descriptions refer to Figure 1–2 below.
Figure 1–2 RMQ Front Panel
Level Meters
In-Monitor
Display (IMD)
Timecode
Status
Headphones
Channels 1 thru 4
Quad View
Menu
HDMI DVI In
F1/Down & F2/Up
Enter
Power
LED
Power On/Off
• Status: The status is displayed in the upper left corner of each window, and includes the input channel number and signal format.
Operation is defined in the OSD CONFIG FORMAT DISPLAY menu.
• Level Meters: Displays up to 16 channels, 8 on the left and 8 on the right. Define the meters setup in the AUDIO CONFIG AUDIO
SOURCE and METER DISPLAY menu options.
• IMD: The 16 characters of the in-monitor display (IMD) can be displayed in red, green, yellow, or white. OSD CONFIG IMD
DISPLAY , IMD COLOR , and IMD CHAR define the static operation.
The second page of OSD CONFIG defines the dynamic IMD and
OSD tally operations.
821097: RMQ Series User Guide
© 2013 Wohler Technologies, Inc. All rights reserved.
7
RMQ Series
Front Panel Features
• Timecode: The display format for the timecode is HH: MM: SS: FF.
In the event no timecode is available, the monitor will display
--:--:--:--. Time code is currently available for SD-SDI ANCpacketized only.
• Headphones: This 1/8” jack receives a standard mini-headphones plug and provides stereo audio. Inserting a plug here, wired or not, will mute the speakers.
• Channels 1 thru 4: Pressing each of these buttons displays one full screen with the input signal connected to the corresponding input on the rear panel. See
for available input types. The audio source (as defined for that channel’s AUDIO
CONFIG menu) will follow the last selected video channel with these buttons. The menus’ channel number also follows the last channel button pressed.
• QUAD: Pressing this button toggles between quad view (shown in
Figure 1–4 on page 10 ) and one-big-and-three-small (as shown in
Figure 1–2 on page 7 ). See also
below for screen identification.
Figure 1–3 Screen Identification
2
Screen 1 Screen 3
Screen 1
Screen 2 Screen 4
3
4
Quad View One-Big-with-Three-Small View
• DVI (HDMI In): Pressing this button toggles between HDMI and
NONE . Set this button to HDMI when you want to display a HDMI input, and set it to NONE when you want SDI input. This control only functions for Channel 1. HDMI jack is provided. DVI-D input requires an adapter (not provided).
• Menu: Pressing this button displays the on-screen display (OSD)
Menu
MENU
. Press MENU again to revert one menu level or exit out of
mode.
8
821097: RMQ Series User Guide
© 2013 Wohler Technologies, Inc. All rights reserved.
RMQ Series
Front Panel Features
• F1/Up and F2/Down: After pressing the MENU button, press Up or
Down to move within submenus. When not in MENU mode, F1 and F2 are programmable hot keys. Refer to
User Config Menu on page 18 for details.
• ENTER: After pressing the MENU button, pressing this button selects the current menu or menu option. Changes are previewed, but not saved, until you press the ENTER button again.
When the OSD Menu is not displayed, you can press the ENTER button to quickly adjust the following parameters.
• VOLUME : Adjusts the volume from 0 to 30.
• BRIGHTNESS : Adjusts the video brightness from 0 to 100, where 50 is the typical value.
• CONTRAST : Adjusts the image contrast from 0 to 100, where
50 is the typical value.
• CHROMA : Adjusts the color saturation from 0 to 100, where
50 is the typical value.
• Power LED: Lights red in standby mode and green when on.
• POWER On/Off: Toggles the monitor to on or standby mode.
• Waveform/Vector: (
) In quad screen view,
Screen 2 displays the waveform or vector for Screen 1 and Screen 4 displays the waveform or vector for Screen 3.
821097: RMQ Series User Guide
© 2013 Wohler Technologies, Inc. All rights reserved.
9
RMQ Series
Rear Panel Features
Figure 1–4 RMQ Waveform/Vector Display
Vector or
Waveform
Displays
Rear Panel Features
The descriptions of the rear panel connectors refer to
and
and
.
Figure 1–5 RMQ Complete Rear Panel
10
821097: RMQ Series User Guide
© 2013 Wohler Technologies, Inc. All rights reserved.
Figure 1–6
RMQ Series
Rear Panel Features
RMQ Rear Panel - Left
• DC IN (jack): Accepts included power plug from an adapter.
• Power (Rocker Switch): Toggles power to the monitor on or off.
• RS485 Ports (2 RJ-45): Input and output connectors for external
control. Refer to Figure 1–7 and Table 1–1 on page 11 for details.
Figure 1–7 RS485 RJ45 Connector Pin Map
Table 1–1 RS485 Pin Out
Pin RS485 In Terminal Signal
4
5
1, 2 GND
3 Tx-
Rx+
Rx-
6 Tx+
7, 8 NC
RS485 Out Terminal
Signal
GND
Tx-
Rx+
Rx-
Tx+
NC
821097: RMQ Series User Guide
© 2013 Wohler Technologies, Inc. All rights reserved.
11
RMQ Series
Rear Panel Features
• Tally (DB-9 F): Tally input.
• Audio Inputs (8 RCA) and Outputs (2 RCA): Each input pair
(one for each channel) accepts standard analog audio. Output is from last (video) channel selected as heard from the speakers/ headphones.
Figure 1–8 RMQ Rear Panel - Right
SDI/CVBS Video Inputs (4 BNC) and SDI Outputs (4 BNC): Only
SDI video, buffered from SDI inputs, is output. No analog to digital or digital to analog conversion is available at this time.
HDMI IN : Alternate input for Channel 1. Accepts HDMI and DVI-D video (adapter required). No audio is available from this input.
HDMI OUT : Sends the main display image, minus menus, to an external monitor.
Ethernet (RJ-45): Network interface for upgrades—reserved for future use.
12
821097: RMQ Series User Guide
© 2013 Wohler Technologies, Inc. All rights reserved.
RMQ Series
Using the OSD Menu
Using the OSD Menu
Configuring the RMQ Series monitors is accomplished in the OSD
MENU . Each of the menus in the OSD MENU is explained below.
1.
Press the MENU button to display the menu.
2.
Use the Up and Down buttons to navigate through the seven sub-menu icons.
3.
Press the ENTER button to move into the parameter selections in the chosen sub-menu. The submenus are:
• STATUS (Read-only; CH indicates the channel being configured)
• COLOR TEMP
• MARKER
• AUDIO CONFIG
• USER CONFIG
• OSD CONFIG
1) Page 1: IMD DISPLAY
2) Page 2: IMD PROTOCOL
4.
Use the Up or Down buttons to cycle through the sub-menus and sub-menu selections.
5.
When the desired option is highlighted, press the ENTER button to select it.
6.
Use the Up or Down buttons to adjust the parameter value up or down, make a selection, or turn a function on or off.
7.
Press the ENTER button to save the parameter change and return to the sub-menu level.
Press the MENU button to back out of a parameter or sub-menu. Press the MENU button again to remove the menu from the screen.
821097: RMQ Series User Guide
© 2013 Wohler Technologies, Inc. All rights reserved.
13
RMQ Series
Using the OSD Menu
Status Menu
Note that none of the options displayed on the STATUS menu are editable.
Table 1–2
Parameters
Status Menu
Default
Value
CH (Channel)
COLOR TEMP
ASPECT MODE
SCAN MODE
IP ADDRESS
SUBNET MASK
SERIAL NO.
MODEL
Domain Range
Display only; Non-selectable. The values vary depending on input signal type and configuration settings.
Color Temp Menu
Important: To modify the options in the COLOR TEMP menu, COLOR TEMP must be set to
USER .
Table 1–3
Parameters
COLOR TEMP
Color Temp Menu
Default
Value
Domain Range
Selects the color temperature that will become the basis for adjustments where:
• D93 = 9300K
D65
• D65 = 6500K
• D56 = 5600K
• USER (Enables the rest of the options)
RED GAIN
GREEN GAIN
BLUE GAIN
Factory
Calibrated
0 to 255
14
821097: RMQ Series User Guide
© 2013 Wohler Technologies, Inc. All rights reserved.
RMQ Series
Using the OSD Menu
Table 1–3
Parameters
Color Temp Menu (Continued)
Default
Value
Domain Range
RED BIAS
GREEN BIAS
BLUE BIAS
RESET
Factory
Calibrated
0 to 63
Resets gain and bias to their factory defaults.
Marker Menu
Important: MARKER is disabled when SCAN mode is NATIVE , or when the input signal is
DVI or VGA.
Table 1–4
Parameters
AREA MARKER
Marker Menu
Default
Value
Domain Range
Select the area marker aspect ratio according to the display aspect only when the aspect ratio is 16:9.
• OFF : turns area marker off
16:9
• 4:3
• 13:9
• 14:9
• 15:9
CENTER MARKER ON
• 16:9
• 1.85:1
• 2.35:1
ON (enabled) or OFF (disabled)
821097: RMQ Series User Guide
© 2013 Wohler Technologies, Inc. All rights reserved.
15
RMQ Series
Using the OSD Menu
Table 1–4
Parameters
Marker Menu (Continued)
Default
Value
Domain Range
Setting the picture safe area size marker for the aspect ratio
(determined by the button to which the aspect function is assigned) and scan control, where:
• OFF
SAFETY MARKER OFF • 80%
• 85%
MARKER LEVEL
MARKER MAT
1
OFF
• 88%
• 90%
• 93%
• 95%
Sets the luminance (white level or brightness) to display safety, center, and area marker line, where:
• 1 = 100%
• 2 = 75%
• 3 = 50%
Sets the area marker mat transparency, where:
• OFF = Normal background, use line for area marker edge only
• HALF = 50% Background brightness
• BLACK = Black
16
821097: RMQ Series User Guide
© 2013 Wohler Technologies, Inc. All rights reserved.
RMQ Series
Using the OSD Menu
Audio Config Menu
The menu sets up the audio sources for each channel according to the last CH 1 to CH 4 button pressed. Speakers and the analog Audio
Output follow CH 1 to CH 4 selections accordingly.
Table 1–5
Parameters
AUDIO SRC
SPEAKER L
SPEAKER R
METER DIS
Audio Config Menu
Default
Value
Domain Range
Used to select the audio source type, where:
NONE
• OFF = Disables audio source
• EXT = Analog audio Inputs CH1 to CH4 selected
CH1
CH2
• EBD = Embed audio (only for
SDI inputs)
Select embedded audio for the left speaker/headphone, line output:
• OFF
• CH1 thru CH16
Select embedded audio for the right speaker/headphone, line output:
• OFF
16CH
• CH1 thru CH16
Select the audio meters to display
(divided evenly between the left and right sides of the monitor:
• OFF
• 2CH
• 4CH
• 6CH
• 8CH
• 10CH
• 12CH
• 14CH
• 16CH
821097: RMQ Series User Guide
© 2013 Wohler Technologies, Inc. All rights reserved.
17
RMQ Series
Using the OSD Menu
Table 1–5
Parameters
ACTIVE ONLY
REF LEVEL
OVER LEVEL
Audio Config Menu (Continued)
Default
Value
Domain Range
OFF
-20DB
Control the audio level meter with the audio source:
ON (enabled) or OFF (disabled)
Select the reference level:
-20DB or -18DB
Select the overload level:
• -10DB
• -8DB
-10DB
• -6DB
• -4DB
• -2DB
User Config Menu
Table 1–6
Parameters
BACKLIGHT
LANGUAGE
PHASE
APERTURE
User Config Menu
Default
Value
N/A
Domain Range
Select the backlight brightness:
0 through 30
Select the language for the menu: english • ENGLISH
50
N/A
• CHINESE
Select the hue/tint adjustment when the video is analog in NTSC format:
0 through 100
Select the image sharpness:
0 through 32
18
821097: RMQ Series User Guide
© 2013 Wohler Technologies, Inc. All rights reserved.
RMQ Series
Using the OSD Menu
Table 1–6
Parameters
F1 BUTTON
F2 BUTTON
LAYOUT 2 MODE
LOCK NUMBER
User Config Menu (Continued)
Default
Value
Domain Range
Marker
Select the function to assign to the function button:
• MARKER
• AUD METER
• WAVEFORM
• NATIVE
AUD
METER
16:9
N/A
• BLUE ONLY
• MONO
• SCAN MODE : Enables or disables display.
• ASPECT MODE : Toggles between 4:3 and 16:9 scaling to match input.
• H/V DELAY
• UNDEF (none)
Select the aspect ratio when the display has one-big-with-threesmall screens:
16:9 or 4:3
Type in up to 16 characters to set a password to unlock the function buttons. Acceptable characters include all letters, numbers, and some symbols.
821097: RMQ Series User Guide
© 2013 Wohler Technologies, Inc. All rights reserved.
19
RMQ Series
Using the OSD Menu
OSD Config Menu
The OSD CONFIG menu has two pages: The IMD DISPLAY and the IMD
PROTOCOL.
OSD Display
Table 1–7
Parameters
IMD DISPLAY
IMD COLOR
TC DISPLAY
(Timecode)
WAVE FORM
WAVE OVER
LIMIT
WAVE UNDER
LIMIT
OSD Config Menu - IMD Display
Default
Value
Domain Range
On
ON = Displays
OFF = Does not display
Select the color in which to display the IMD text:
• RED white
• GREEN
• YELLOW
IMD CHARACTER WOHLER on off
0
0
• WHITE
The IMD text can contain up to 16 characters including all letters, numbers, and some symbols.
ON = Displays SD-SDI ANC-VITC/
LTC.
OFF = Does not display.
Select the graph to display:
• OFF
• WAVE FORM
• VECTOR 75
• VECTOR 100
Select the waveform overload limit:
0 through 100
Select the waveform under limit:
0 through 100
20
821097: RMQ Series User Guide
© 2013 Wohler Technologies, Inc. All rights reserved.
RMQ Series
Using the OSD Menu
Table 1–7
Parameters
OSD Config Menu - IMD Display
Default
Value
Domain Range
Select to display the video information:
FORMAT DISPLAY off • OFF
• AUTO
• ON
This following feature is not currently available.
Select to display closed captions for
CVBS signals only:
• OFF
CC off
• CC1
• CC2
• CC3
• CC4
• TEXT1
• TEXT2
• TEXT3
• TEXT4
• XDS
821097: RMQ Series User Guide
© 2013 Wohler Technologies, Inc. All rights reserved.
21
RMQ Series
Using the OSD Menu
IMD Display
Table 1–8
Parameters
IMD PROTOCOL
OSD Config Menu - IMD Protocol
Default
Value
Domain Range
Select the IMD protocol you want to use:
Local
• LOCAL
• UDP
• TSL3.1
• TSL4.0
IMD ID
IMD NAME (S/N)
BAUD RATE
OSD TLY MODE
0
N/A
19200
T1
• IMAGE VIDEO
Select the IMD ID:
0 through 255
The IMD serial number contains up to 16 characters.
Select the communications baud rate:
• 9600
• 19200
• 38400
Select the OSD tally mode:
• RG : Red/Green
• GR : Green only
• RGY : Red/Green/Yellow
• OFF : No tally light
22
821097: RMQ Series User Guide
© 2013 Wohler Technologies, Inc. All rights reserved.
RMQ Series
Using the OSD Menu
Table 1–8
Parameters
IMD TLY MODE
TLY SOURCE
OSD Config Menu - IMD Protocol
Default
Value
Domain Range
Select the IMD tally mode:
• T1
T1
• T2
• T1T2
• T2T1
• T1-
Standard
• T2-
• T1T2-
• T2T1-
Select the tally source (For more information about the tally DB-9 switch closure, refer to the information about the rear panel in
• STANDARD
• IMAGE VIDEO HW
• IMAGE VIDEO 422
• STANDARD + IM422
• TSL
821097: RMQ Series User Guide
© 2013 Wohler Technologies, Inc. All rights reserved.
23
RMQ Series
Specifications
Specifications
The general specifications of the RMQ Series monitors are listed in
below.
Table 1–9 RMQ Specifications
Specification RMQ-230s
Dimensions
(including the fixed table stand)
14.37” H x 21.85” W x 6.26” D (
(365mm H x 555mm
W x 159mm D)
Shipping Weight 16 lbs. (7.26 kg)
LCD Dimension 23”
Aspect Ratio
Resolution
4:3/16:9 (native)
1920 H x 1080 V
Color Depth 16.7M, 24-bit
Viewing Angle 178° (H/V)
Brightness
Contrast Ratio
250 cd/m
2
1000:1
RMQ-200s
13.0” x H x 19.0” W x
6.3” D
(330 mm H x 482 m
W x 159 mm D)
14.1 lbs. (6.41 kg)
20”
1600 H x 900 V
RMQ-170s
12.1” H x 17.2” W x
6.3” D
(308 mm H x 437 mm
W x 159 mm D)
12.1 lbs. (5.50 kg)
17”
1366 H x 768 V
350 cd/m
2
below lists the I/O specifications.
Table 1–10 RMQ Specifications
Specification
Video Inputs
RMQ Values
• 4 BNCs: CVBS, 3G/HD/SD-SDI
(supports embedded audio)
Video Outputs
Audio Inputs
Audio Outputs
• 1 DVI -D / HDMI: alternate IN1
1 HDMI: HDMI (1080p50 or 1080p60)
8 RCAs: Analog stereo for EXT sources
2 RCAs: Analog stereo (monitoring, same as speakers)
24
821097: RMQ Series User Guide
© 2013 Wohler Technologies, Inc. All rights reserved.
RMQ Series
Specifications
below distinguishes each of the RMQ models.
Table 1–11 RMQ Distinctions Among Each Model
Category
3G-SDI
HD-SDI
SD-SDI
Analog
Specification
1080p: (60/59.94/50)
1080i: (60/59.94/50)
720p: (60/59.94/50)
1035i: (60/59.94)
480i: (60/59.94)
576i: (50)
PAL
NTSC
1080i: (60/59.94/50)
720p: (60/59.94/50)
1035i: (60/59.94)
480i: (60/59.94)
576i: (50)
PAL
NTSC
480i: (60/59.94)
576i: (50)
PAL
NTSC
PAL
NTSC
3G HD SD
Note: 1080sF will display as the equivalent 1080i rates listed above.
A
below lists the specifications for CVBS inputs.
Table 1–12 RMQ CVBS I/O Specifications
Specification
Signal Type
Signal Amplitude
Impedance
Return Loss
DC Offset
Frequency Response
Differential Gain
Differential Phase
RMQ Values
NTSC, PAL
1V peak-to-peak ±3 dB
75
> 40 dB ±5 MHz
0V ±0.05 V
±0.2 dB to 5 MHz
< 1%
< 1.5°
821097: RMQ Series User Guide
© 2013 Wohler Technologies, Inc. All rights reserved.
25
RMQ Series
Technical Function Overview
below lists the specifications for SDI inputs.
Table 1–13 RMQ SDI Specifications
Specification RMQ Values
Signal Compliance
Connector
Impedance
Return Loss
SMPTE 424M/425M-A, SMPTE 292M,
SMPTE 259M, SMPTE 297M (audio)
BNC per IEC 169-8
75
>18 dB at 5 to 270 MHz
>15 dB at 270 MHz to 1.5 GHz
>10 dB up to 3 GHz
Maximum Signal Level 800 mV peak-to-peak, 10%
Signal Amplitude 800 mV peak-to-peak, 10%
DC Offset
Overshoot
Total Jitter
0 V ±0.5 V
<10%
<0.2 UI
3G (3Gb/s): <135 ps
Rise and Fall Time HD (1.5 Gb/s): <270 ps
SD: <700 ps
Technical Function Overview
below illustrates the overall functionality of the RMQ Series monitors.
26
821097: RMQ Series User Guide
© 2013 Wohler Technologies, Inc. All rights reserved.
Figure 1–9
RMQ Series
Technical Function Overview
RMQ Block Diagram
821097: RMQ Series User Guide
© 2013 Wohler Technologies, Inc. All rights reserved.
27
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project