Self-Cleaning manual 2009

Self-Cleaning manual 2009
2009
HYDROPOOL
self-cleaning
hot tubs
owner’s manual
Hydropool Industries:
Tel: 905.565.6810
Toll Free: 1.800.465.2933
Fax: 905.565.6820
Email: [email protected]
www.hydropoolhottubs.com
99399
table of contents
Letter of introduction....................................................................3
Jet and Feature Operation
Jet Identification Chart.......................................................25
Flow Adjustment..................................................................25
Removal and Replacement.................................................26
Diverter Valve......................................................................26
Waterfall Control (optional)................................................26
Important User Safety Instructions
Warnings................................................................................4
Hyperthermia.........................................................................4
Choosing the Right location
Indoor Locations...................................................................5
Outdoor Locations.................................................................5
Hydropool Surround Sound Audio and
Audio/Video Systems Section (optional).................................27
General Installation Considerations...........................................6
Hot Tub Water Balance
General Overview................................................................44
Initial Fill...............................................................................44
Glossary of Common Water Maintenance Terms............45
Water Balance Summary for your Hot Tub (chart)..........45
Water Balance Troubleshooting........................................46
Corona Discharge Ozone Technology...............................47
Special Considerations
Indoor Installations...............................................................6
Outdoor Installations............................................................6
Site Preparation
Above Ground Installations..................................................7
In-ground & Partial In-ground Installations.......................7
Overall Support......................................................................7
Remote Equipment Placement.....................................................8
Routine Hot Tub Maintenance
Daily, Weekly, Monthly, Quarterly.....................................47
Cleaning the Skimmer Basket............................................47
Cartridge Filter, Removal, Cleaning, Re-installation........48
Cleaning the Acrylic Surface.............................................48
Safety Hard Cover...............................................................48
Changing your Hot Tub Water............................................49
Draining your Hot Tub Water.............................................49
Unloading/Handling your Hot Tub...............................................8
Hydropool Exclusive Quick-Drain™ & Fill (diagram)................50
Important Electrical Safety Instructions....................................9
G.F.C.I./R.C.D. Application Guideline & Wire Size..............9
North America G.F.C.I. Installation Diagrams...................10
Europe R.C.D. Installation Diagram...................................11
Wood Products
Cabinet Wing-Locks............................................................51
Protecting your Cabinet Wood Finish...............................51
Gazebos................................................................................51
Accessories
Pillows..................................................................................12
Filter/Ice Bucket Lids..........................................................13
LED Mood Lighting..............................................................13
Safety Hardcover Locks.....................................................13
Cover Remover (optional)...................................................13
Winterizing your Hydropool Hot Tub.........................................52
Leveling your Hydropool Hot Tub................................................7
Equipment Accessibility & Protection.......................................8
General Troubleshooting............................................................53
What to do in the event of
Power Fluctuations.............................................................54
Cold Weather Power Failure..............................................54
Filling, Checking and Starting your Hot Tub............................14
Pump Priming/Releasing an Air Lock................................14
Hydropool Control Systems
North America
Silver & Gold Series............................................................16
Platinum & Titanium Series/Limited & Luxury Edition.....19
Topside Control Panel Display Messages...............................23
2
On behalf of everyone at the company, we thank you for your decision to purchase a Hydropool hot tub.
Recognized for quality worldwide, we are confident that your new hot tub will provide you, your
family and friends, with years of enjoyment and fulfill all your hydrotherapy needs.
Hydropool hot tubs are not only healthful and relaxing, they can even add value to your home.
Please take the time to carefully read and understand all the safety, installation and operating
instructions in this manual before electrically connecting your hot tub and adding water.
The following pages contain valuable information and pointers that will save you both time and
money, as well as help you to simplify upkeep and maintenance.
Since we manufactured our first hot tub in 1985, the Hydropool team has been dedicated to producing
a quality product catering to maximum hydrotherapy, comfort, energy efficiency and ease of operation.
We are confident that as you become more familiar with the various safety and maintenance features
of your new hot tub you will be satisfied that you made the right decision in purchasing a Hydropool
hot tub.
Happy hot tubbing...
David Jackson
President
3
S ave these instructions
Important user safety instructions
Your physiological response to hot water is subjective and depends on your age, health, and medical history. If you don’t
know your tolerance to hot water, or if you get a headache, or become dizzy or nauseous when using your hot tub, get
out and cool off immediately.
WARNINGS
HYPERTHERMIA
3
The causes, symptoms and effects of hyperthermia may be
described as follows:
Hyperthermia occurs when the internal temperature
of the body reaches several degrees above the normal
body temperature of 37˚C (98.6˚F). The symptoms of
hyperthermia include drowsiness, lethargy, and an increase in
the internal temperature of the body. The effects of
hyperthermia include:
• Unawareness of impending hazard
• Failure to perceive heat
• Failure to recognize the need to exit the hot tub
• Physical inability to exit the hot tub
• Fetal damage in pregnant woman
• Unconsciousness resulting in the danger of drowning
4
5
6
7
8
9
10
11
12
13
14
15
16
17
1 Children should NOT use a hot tub
without alert adult supervision.
2 Children should not enter a hot tub where
water temperature exceeds body
temperature (37˚C / 98.6˚F).
Prolonged immersion in water temperatures in excess
of 38˚C (100˚F) may be injurious to your health. We
recommend establishing lower temperatures and
shorter use periods for young children and/or those
users potentially affected by hot temperatures. Always
confirm water temperature with an accurate
thermometer before entering your hot tub.
Do not allow children to submerge their head
under water.
Do not use a hot tub unless all suction guards are
installed to prevent body and hair entrapment. Do not sit
in front of, or on top of the suction fittings or skimmer,
as this will obstruct proper circulation and may result in
personal injury.
Never operate the hot tub pump at high speed without
having all suction and return lines open.
Always keep the hardcover installed and locked when
the hot tub is not in use.
People using medications and/or having any adverse
medical history should consult a physician before using
a hot tub.
People with infectious diseases should not use a hot tub.
Exercise caution when entering or exiting a hot tub.
Where practical, install a safety grab bar or handrail.
Turn off the jets before entering the hot tub to improve
visibility of the steps or flat entry area.
To avoid unconsciousness and possible drowning, do not
use drugs or alcohol before or during the use of a hot tub.
Pregnant woman should consult a physician before
using a hot tub.
Do not use a hot tub immediately following strenuous
exercise.
Do not permit or use electric appliances (such as a light,
telephone, radio or television) within 1.5 m (5 ft) of this
hot tub, unless such appliances are rated at 12VDC or less.
Test the GFCI (Ground Fault Circuit Interrupter) monthly.
Post emergency phone numbers for Police, Fire Dept.,
and Ambulance at the nearest phone.
Maintain water chemistry/balance in accordance with
manufacturer’s instruction
Since your hot tub can be set to reach temperatures of 40˚C
(104˚F), users should be aware that extended submersion in
water that exceeds normal body temperature can lead to
hyperthermia.
If you sense any of the symptoms of hyperthermia, safely
exit the hot tub immediately.
WARNING
THE USE OF ALCOHOL, DRUGS OR MEDICATION
CAN SIGNIFICANTLY INCREASE THE RISK OF
FATAL HYPERTHERMIA.
4
CHOOSING THE RIGHT LOCATION
Your Hydropool hot tub can be installed indoors or out, on the ground, in the ground or half-and-half. The following
information will assist you in choosing the right location for your individual needs. When making your decision,
always remember that hot tubs can be enjoyed year-round, indoors or out, regardless of the climate. Many Hydropool
owners report that their favourite time to use a hot tub is in the cooler fall and winter months, while others praise the
enjoyment of using their hot tub in the warmer spring and summer months.
INDOOR LOCATIONS
These ‘split’ and lower profile versions are designed to
accommodate narrow doors or shallow stairwells. Since the
dimension from the seat to the top of the lip is identical to
the “regular profile” units, water submersion, for even the
tallest user, is the same.
If members of your family are not cold weather enthusiasts,
or if your backyard or patio area is not suitable for a hot
tub installation, then an indoor location for your hot tub
may be your best or only choice. You may wish to create an
exercise/spa area in your home, or install your hot tub in a
glass solarium or four-season room adjoining your home.
Indoor installations not only add a unique look and appeal
to your home, they provide the privacy and controlled
climate to ensure that use and enjoyment of your hot tub
is maximized.
Your Hydropool dealer can even arrange for your hot tub to
be shipped without a cabinet or with the cabinet packaged
separately for on-site installation. In many cases the smaller
dimensions of a hot tub without a cabinet is all that is
needed to ensure the hot tub can be delivered without wall
or door alterations.
If you are considering an indoor location, Hydropool
manufactures certain lower profile models in two pieces
(referred to as ‘split’ models) that can be easily moved into
most tight or difficult access locations and then assembled
on-site by your authorized Hydropool dealer.
Where the hot tub is being recessed, or a custom deck or
tile is being installed, the cost savings of being able to order
a hot tub without a cabinet is another benefit of choosing
Hydropool.
If you should choose an indoor location, you will find
further information as outlined in the section
“SPECIAL CONSIDERATIONS FOR INDOOR INSTALLATIONS”
OUTDOOR LOCATIONS
For those who choose an outdoor location, hot tub
operating temperatures can be adjusted to match the
season. In colder months, many owners will operate their
hot tub in the range of 38-40˚C (101 -104˚F). During
warmer months, an operating temperature of 36-37˚C (9799˚F) will provide a refreshing retreat.
If you should choose an outdoor location, you will find
further information as outlined in the section
“SPECIAL CONSIDERATIONS FOR OUTDOOR INSTALLATIONS”
For a variety of reasons, outdoor locations are a far more
popular choice. Some of the reasons include:
• Limited indoor space
• Delivery complications due to door openings, stairwells, etc.
• Limited budget (indoor installations usually also involve
interior home renovations)
• Desire for an outdoor entertainment center
• Hot tub is being installed adjacent to an existing or
planned swimming pool
• Concerns over splashing water inside the home
5
GENERAL INSTALLATION considerations
1 Your HYDROPOOL Hot Tub is a self-contained pre-plumbed
unit, so that no on-site plumbing connections to the
residential water supply or drain are required.
2 Ensure that your HYDROPOOL Hot Tub is properly
supported by either a level concrete pad, or a properly
constructed deck capable of supporting 1220 kg/m2
(250 lbs./ft.2). If there is a possibility that the pad could
shift by freezing/thawing ground movement (such as
in clay regions, and/or areas with high water tables)
concrete footings extending below the frost line are
recommended.
3 Decking should be chosen and constructed in a manner
that minimizes the chance of slipping or falling.
4 Level your hot tub using wood shims where necessary,
ensuring that the tapered end extends at least 61 cm (24 in.)
under the unit.
5 If you do not have a factory installed foamed cabinet, it
is assumed that you are building your own custom
cabinet, tiling or decking. Please consider the following:
aYour HYDROPOOL Hot Tub is self-supporting on its
base. The cabinet should be decorative only, not for
support. Never suspend the hot tub from the deck or
cabinet.
bWhere the hot tub is not equipped with a factory
installed cabinet, it is the installer’s responsibility to ensure all electrical equipment is weather
protected.
cAlways provide adequate access for servicing the
support equipment.
dDecking should be constructed to allow repair access
around the entire hot tub.
eIn remote equipment or no-cabinet installations,
you may add extra insulation, but the equipment
area must have adequate cross-flow ventilation.
6Installation of a safety grab rail or reachable support
for use when entering or exiting the hot tub is
recommended.
7A nearby garden hose connection is recommended for
filling and “topping up” the hot tub.
The hot tub equipment and all electrical
plugs, outlets and lights within 1.5m (5ft)
of the hot tub must be G.F.C.I protected.
Consult your electrician or local electrical
authority for further details.
Access to the hot tub must always be secured:
Outdoors - in accordance with local property by-laws
and/or via an approved fence with a self-closing gate
and a safety hardcover; Indoors - by a lockable door and
a safety hardcover.
SPECIAL CONSIDERATIONS
Indoor InstallationS
Outdoor InstallationS
• W
hen the hot tub is to be installed in a small room
(under 150 ft2/14 m2), we recommend that large units
be fully or partially submerged in-floor so that it does
not dominate the room. This will also provide greater
overhead clearance for entry and exit to and from the
hot tub
• It is beneficial to have the hot tub room located near wash
room and shower facilities
• The hot tub room should have a floor drain to handle
splash water, a window, outside exhaust fan or humidistat controlled exhaust fan for ventilation. Where this
is not practical, the use of indoor/outdoor carpeting or
a tile floor and the opening of a window while the hot
tub cover is removed should be sufficient. You should
not have concerns regarding humidity. When the hardcover is installed, no humidity will escape. During use, the
small amount of humidity released into the room can be
removed with the use of a dehumidifier
• Consider plumbing a water tap and drain location nearby
to facilitate draining and top-up
• Always provide adequate ventilation for the support
equipment
• Consult your local Hydropool retailer for further information
• C
ontact your local building code department to
determine if a building permit is necessary and for
information on applicable bylaws (distance from property
lines, buildings, fencing requirements, etc.)
• If you are doing any excavating, contact your local gas,
electric, and cable-company to ensure that there are no
underground lines
• Locate the hot tub, where practical, within close distance
of a door to the house to maximize potential winter use.
• Ensure that all hot tub support equipment is easily
accessible and protected from the elements
• If possible, locate the hot tub where you will enjoy
some privacy, out of the site of neighbours. If this is not
possible, a partial privacy or wind partition, or proper
placement of the optional Hydropool cover lifter should
provide adequate privacy
• The hot tub support equipment is designed for indoor (out
of the direct elements) use. When your HYDROPOOL
hot tub is equipped with a factory-installed cabinet,
and installed as per the guidelines of this manual, the
equipment will be adequately protected. If the hot tub is
shipped without a cabinet, your custom cabinet or
other structure must be designed to supply protection for the hot tub support equipment from rain,
snow, splash water, etc., but still designed in a manner
to ensure adequate ventilation.
6
Site preparation
Above-ground Installations
• N
on-freezing climates – it is sufficient to ensure that the
base of the hole or cavity created for the tub has a dry,
stable, compacted level base and proper drainage
• Climates where freeze/thaw occurs – it is necessary that a poured level concrete base, complete with
concrete footings, be installed as outlined in the section
ABOVE-GROUND INSTALLATIONS
• Areas with a high ground water table – a level concrete
base, as well as a concrete or wood retaining wall to
hold back the earth, is recommended. This forms a box or
‘bunker’, in which the hot tub is placed
• ALWAYS ensure that there is good drainage, via a
properly designed French drain (gravel) system and/or a
sump pump, to prevent ground water flooding damage
to the support equipment or hot tub structure
• Install protective waterproof conduit to house light,
or topside control cables that will be buried
• Access for future service must be considered at the
time of design and installation. Difficult access can
result in supplemental service labour charges not covered by the factory warranty. Consider easily removable
deck materials.
Where the hot tub is a “stand-a-lone” above-ground
installation to be installed in regions where freeze/thaw
conditions may occur, a level patio stone or pre-formed
paver type base may be sufficient if there is no abutting
deck(s) that could be damaged during potential seasonal
movement of the ground. The potential drawback to
this type of base is that splash water could eventually
de-stabilize the ground under the base, with the resultant
shift of the support base causing damage to the hot tub
structure.
For best results, we recommend the installation of a level
concrete pad:
• Dig out and level the ground 20-30 cm (8-12 in.) below
your desired base level
• Install 10-15 cm (4-6 in.) of crushed stone
• Next, install 10-15 cm (4-6 in.) of poured concrete
• Level the concrete and apply a broom-type finish
• We recommend that the pad be made 15 cm (6 in.) larger
than the hot tub on three sides, and 1 m (3 ft.) larger
on the side where the access steps and/or planters will
be installed
OVERALL SUPPORT
In regions where freeze/thaw occurs, or where there will
be custom decking abutting the hot tub we recommend
the installation of sono-tubes beneath the pad to prevent
shifting.
Your Hydropool hot tub is equipped with a factory
installed load support substructure, which distributes the
weight of the water over the entire foot area of the hot
tub. The cabinet, either factory installed or customized
on-site, should be decorative only, and not relied on for overall
support. Never suspend a hot tub from a deck or floor by
the outer acrylic edge, as this will lead to product damage
and/or serious personal injury.
IN-GROUND & Partial IN-GROuND
INSTALLATIONS
For units being installed fully or partially in the ground,
the type of support will again vary based on whether or
not the tub is being installed in an area with freeze/thaw
conditions. Hydropool does not recommend back-filling full
in-ground or partial in-ground installations.
WOOD OR
CONCRETE DECK
FACTORY
FOAM
INSULATION
WOOD OR
CONCRETE
DECK
CONCRETE
OR WOOD
RETAINING
WALL
FACTORY INSTALLED
PLUMBING
ORIGINAL
COMPACTED
EARTH
OPEN CAVITY
BELOW
FROST
LINE
FACTORY INSTALLED
PLUMBING
POURED 4" SLAB
POURED 4" SLAB
6" GRAVEL
FRENCH DRAIN
6" GRAVEL
CONCRETE
FOOTINGS
LEVELING YOUR HYDROPOOL HOT TUB
After the hot tub is properly positioned on the support base,
the entire unit should be checked with a level and shimmed
as necessary. Should you find that the support base is sloped
or otherwise uneven, level your hot tub using TAPERED
wood shims where necessary, ensuring that the tapered
end extends at least 61 cm (24 in.) under the unit. This
will insure contact with the support substructure to
appropriately distribute the weight of the unit. Do not
just shim under the cabinet base outside edge, as this will
cause structural stress on the unit, potentially causing
unwarrantable damage to the hot tub structure and /or
shell.
7
EQUIPMENT ACCESSIBILITY
and Protection
remote EQUIPMENT Placement
Whenever possible, install the pump(s) and control with
heater below water level to ensure easy priming and
maximize performance. Where above-grade equipment
location is necessary, please ensure that your hot tub is
equipped with the Remote Above-Grade Equipment Package.
The equipment must be located in an area where it will
remain dry and will not be exposed to rain, snow or ground
water. The standard Hydropool hot tub has the equipment
installed inside the protective cedar cabinet.
• The equipment should be located as close to the hot
tub as possible to maximize jet performance.
• Where you have ordered your hot tub with optional
remote equipment, ensure that the equipment is not
located more than 3 m. (10 ft.) from the hot tub.
• Use only 2 in. flex-pipe or larger for the pipe runs from
the equipment to the hot tub, with minimal use of elbows
or other pipe restrictions.
• Install protective waterproof conduit to house
applicable cords or line extensions such as the sensor
and top-side control cables, light wires or ozone tubing.
• In climates where freeze / thaw occurs we recommend that
remote plumbing lines be buried below the frost line and
that pipe insulation is applied over all pipes that run from
the hot tub to the remote equipment to help maintain
energy efficiency.
• W
hen your hot tub is to be installed above-ground, the
cabinet is designed for both protection and accessibility
• When your hot tub is to be installed fully or partially
in the ground, if you are relocating the equipment
remotely from the hot tub, or if you have ordered a
hot tub without a cabinet: it is necessary that the
equipment is installed in an area that is dry, protected
from the elements, has proper ventilation and is easily
accessible for service
• Always ensure that the equipment is mounted on a raised
base or platform to prevent potential water damage to
the motor, equipment or controls
• Ensure that access to the equipment and the
working area around the equipment is large enough to
accommodate a service person
UNLOADING / HANDLING YOUR HOT TUB
All Hydropool hot tubs are shipped with a protective
combination layer of foam wrap, cardboard and plastic
film. Each hot tub is factory strapped onto a wood skid. If
your hot tub is to be delivered by your local dealer, it will
generally arrive on a flat bed truck or low profile trailer.
Most dealers are equipped with the necessary equipment
to maneuver the hot tub from the truck to the dolly
or cart that will be used to move your hot tub to the
installation location.
Most Hydropool models require a clearance width of at
least 100 cm. (39 in.) to allow movement of the unit on its
side through alley-ways, fence openings, etc. Where this is
not possible, the use of a crane to lift the hot tub from the
truck or trailer over the house to the patio or yard is often
a simple and economical option.
• Do not move or place the hot tub on
the side where the equipment is located
as damage could occur
• Never roll or flip the hot tub end over
end as the cabinet could be
damaged
• Never lift or handle the hot tub by the
plumbing
• Make sure that there is sufficient assistance to gently
slide the hot tub off the dolly or cart to the support base
without any damage
Should your hot tub arrive in a common closed box trailer,
it may be necessary to arrange with a local towing company
for a tilt and load tow truck, with a pulley winch system,
to pull the skid from the larger trailer to the lower profile
tow truck flat bed. The hot tub can be gently slid off the
low profile trailer and positioned on its side on a cart or
dolly.
Important Note: Damage caused during transportation
or by improper handling is not covered by the factory
warranty.
8
IMPORTANT ELECTRICAL SAFETY INSTRUCTIONS
Safety comes first. When installing & using this electrical equipment, basic safety precautions MUST
always be followeD!
1 READ AND FOLLOW ALL INSTRUCTIONS
2 Electrical installation must be completed by a qualified
electrician in accordance with all National, Regional
and Local Codes and Regulations in effect at the time
of installation.
3 Connect only to a dedicated circuit protected by a class
‘A’ two-pole ground fault circuit interrupter (GFCI)
4 Use copper conductors only!
5 The hot tub equipment and all electrical plugs, outlets
and lights within 1.5m (5ft) of the unit must be G.F.C.I
protected. Consult your electrician or local electrical
authority for further details.
6 A green colored terminal or a terminal marked “G”, “GR”,
“Ground”, or “Grounding” is located inside the supply
terminal box or compartment. To reduce the risk of
electric shock, this terminal must be connected to the
grounding means provided in the electric supply service
panel with a continuous copper wire equivalent in size to
the circuit conductors supplying the equipment.
7 At least two lugs marked “BONDING LUGS” are provided on
the external surface or on the inside of the supply terminal
box or compartment. To reduce the risk of electric
shock, connect the local common bonding grid in the
area of the hot tub to these terminals with an insulated
or bare copper conductor not smaller than No.6 AWG
(Canada/Europe) / No.8 AWG (USA).
8 All field installed metal components such as rails, ladders,
drains or other similar hardware within 3 m (10 ft) of the
hot tub shall be bonded to the equipment grounding bus
with copper conductors not smaller than No.6 AWG.
G.F.C.I./R.C.D. Application Guide for
hydropool Self clean series
NORTH AMERICA
Silver Series/Gold Series
Platinum Series/Luxury Edition
Titanium Series/Titanium Plus Series
40A
50A
60A
EUROPE
Silver Series/Gold Series/Platinum Series/Luxury Edition 20A
Titanium Series/Titanium Plus Series
40A
Wire Size
North America
• The minimum wire size for systems that require a 40A
GFCI is #8/3 c/w ground
(also refered to as #8 gauge / 4 conductor).
• The minimum wire size for systems that require a 50A or
60A GFCI is #6/3 c/w ground
(also refered to as #6 gauge / 4 conductor).
Europe
• The minimum wire size for European system is 2.5 mm2
copper wire.
Important Note:
• This guide is for standard installations where the wire
run is 15 m (50 ft.) or less. For longer wire runs, consult a
qualified electrician.
9
North America – GFCI INSTALLATION
Important Note: Installation of the GFCI - Circuit Breaker, including ampere sizing and selection of
conductor size and type, must be performed by a qualified electrician in accordance with the National
Electrical Code, or the Canadian Electrical Code, and all Federal, State/Provincial and local codes and
regulations in effect at the time of installation.
SIEMENS - TYPICAL
O
N
NOTE THIS - The white Neutral wire
from the back of the GFCI MUST be
connected to an incoming Line
Neutral. The internal mechanism of
the GFCI requires this neutral
connection. The GFCI will not work
without it.
60
60
O
F
F
TEST
W hite W ire
Line Neutral
LOAD
POW ER
LOAD
NEUTRAL
LOAD
POW ER
LINE NEUTRAL From
Electric
Service
Panel
or
Other
Source
LINE 2 - INPUT
LINE 1 - INPUT
GROUND
GROUND - INPUT
Note : Ground
bar (included)
must be installed
in panel.
GROUND TO SPA
LOAD 2 -
To hot tub
support
equipment
120 volts
LOAD NEUTRAL -
240 volts
120 volts
LOAD 1 -
square d - TYPICAL
Bottom View of G.F.C.I.
(Square D)
Front View of G.F.C.I. (Square D)
10
WHITE
WHITE
TBI
WHITE (NEUTRAL)
BLACK (HOT)
RED (HOT)
GREEN (GROUND)
GRN (GROUND)
WHITE
RED (HOT)
WHITE
GRN (GROUND)
BLACK (HOT)
BLACK (HOT)
WHITE
BLK (HOT)
RED (HOT)
GRN
WHITE (NEUTRAL)
RED (HOT)
BLACK (HOT)
GRN (GROUND)
RED (HOT)
1
2
3
4
5
Europe – R.C.D. Installation - Typical
Important Note: Installation of the R.C.D. - Circuit Breaker, including ampere sizing and selection of
conductor size and type, must be performed by a qualified electrician in accordance with National,
Regional and Local Codes and Regulations in effect at the time of installation.
House Breaker Box
(Neutral)
To Hot Tub Support
Equipment
11
ACCESSORIES
PILLOWS
Tubular Pillows
The tubular pillows are a friction fit. Simply compress the
ends slightly, and slide into the semi-circular recess above
the seat or lounger, with the Hydropool logo facing out.
Corner Wrap Pillows
The corner wrap pillows are pre-installed at the factory
and are attached via pin and socket. To remove, grasp ends
of pillow and pull away from hot tub seat. To re-install,
lineup pins on back of pillow to mounting sockets and press
firmly.
Although the pillows are designed to remain in-place in the hot tub, to extend the life of the pillows, remove after each use.
Waterfall Pillows
If you received the optional waterfall package, remove the blade from the waterfall receiver fitting in the hot tub (already
installed at the factory). Insert the waterfall blade through the front of the special waterfall pillow. The front flange of
the waterfall blade will be recessed into the front of the pillow. If it is not recessed, the blade needs to be removed and
re-inserted through the opposite side of the pillow. Push the pillow into the semi-circular recess, ensuring that the portion
of the blade protruding out of the back of the pillow inserts firmly into the waterfall receiver fitting.
12
FILTER/ICE-BUCKET LIDS
The filter and ice-bucket covers provide that finishing touch to your Hydropool hot tub. As the
covers are identical to each other, simply place over either opening for a finished appearance.
LED Mood lIGHTing
Press the ‘light’ pad on the topside control to start the following LED lighting modes. Pressing the
‘light’ pad on/off within 3 seconds cycles through the various ‘light shows’. When the LED lighting is turned off for more
than 5 seconds, then turned back on, the system will resume the last ‘light show’.
Description of Light Shows:
• Mode 1 – Synchronous colour change
• Mode 2 – Freeze mode, freezes on selected colour blend from above mode (gives unlimited colour blend selection)
• Mode 3 – solid colour blue
• Mode 4 – solid colour green
• Mode 5 – solid colour red
• Mode 6 – solid white (simulated)
For systems with optional Galaxy light package:
• Mode 7 – Galaxy lights OFF; interior lights ON
• Mode 8 – Galaxy lights ON; interior lights OFF
SAFETY HARDCOVER LOCKS
The safety hard cover is designed to open away from the
control area, however, if the hot tub is symmetrical in
dimension, the cover can be oriented to open in either
direction. Simply place the cover on the hot tub, pull the
straps down so that they are fully extended, then release
slightly so that there is approximately 6 mm (1/4 in.) of
slack. Mark the position on the cabinet, and fasten the
receiver clip with the screws provided.
WARNING
Always ensure the safety hard cover is
in place and locked whenever the hot tub
is not being used.
OPTIONAL COVER REMOVER
Hydropool offers several different devices to assist in the removal of the safety hard
cover. Please refer to the instructions supplied with your particular cover remover
for installation. For further information, contact your local Hydropool retailer.
13
FILLING, CHECKING AND STARTING YOUR HOT TUB
Checking
• Although your hot tub was thoroughly water-tested in
the factory, some loosening of fittings can occur during
shipping. Before any decking, tiling or carpeting is
completed around the installation, fill and operate
your hot tub to test for leaks (this ensures easy access
and inexpensive correction). Check all union connections
and plumbing for minor leaks. In the event of a leak,
ensure all union connections and pump plugs are tight
and all o-rings/gaskets are in place.
Starting
• Before applying voltage to power-up your hot tub, it
is very important that you understand the sequence of
events that occur when the system is activated in order
that the pump can be primed efficiently and damage to
the system can be avoided.
Unions
• Turn the main power “on” at your electrical panel.
• F ollow the control instructions for your particular model
hot tub to put the pump into low speed. See section
Hydropool CONTROL Systems
Gate Valves
Hose Bib
PUMP PRIMING/RELEASING AN AIR LOCK
• On some systems a
message will appear on the
display indicating that the system is in pump Priming
Mode. This mode will last for 4 to 5 minutes before
automatically entering the normal operation mode. See
complete details for your spa in section HYDROPOOL
CONTROL SYSTEMS
Proper
Water
Level
Filling
• When adding water for the first time, the hot tub should
be filled through the skimmer opening (helps to prevent
air locks) using a standard garden hose, turning the tap on
slowly to prevent damage to the surface by a jerking hose
connection.
• P
ull up the handles on the intake and return gate valves
(handles are pulled up when valves are open and pushed
down when valves are closed).
• When the hot tub pump is located below water level, the
water should start circulating immediately. If the motor
works but you do not notice water circulation within the
first 15 seconds, the pump may require priming due to
trapped air (referred to as an ‘air lock’). To prime, open the
hose-bib to allow trapped air to escape. Close as soon as
the water flow from the jets becomes regular. If the pumps
have not primed after 2 minutes, and water is not flowing
from the jets, DO NOT allow the pumps to continue to
run. Turn power off at the main house panel (or GFCI) and
try releasing the air again by loosening the union on the
discharge side of the pump(s) while the motor is not
running. Turn the power back on. If the pump(s) does not
prime after 15 seconds, sometimes momentarily turning
the pump(s) off and on will help the system to prime
(note: do not do this more than 5 times).
• Important: Under NO circumstances should the pump(s)
be allowed to operate without priming beyond 5
• Ensure the drain hose-bib is closed.
minutes, as this may not only cause unwarrantable
damage to the pump, it may also cause the control
• Ensure that all jets are open. See section JET & FEATURE
system to go into an overheat condition.
OPERATION
Definition: ‘Priming’ a pump is a term used to describe the
• F ill the hot tub to the recommended level, approximately process in which air trapped in the plumbing and pump
19 mm (3/4“) from the top of the skimmer opening.
wet-end (referred to as an ‘air lock’) is released, allowing
the pump to move water efficiently through the plumbing
system and to the jets.
14
RELEASING AIR TRAPPED IN FILTER...
• When the pump starts circulating on low speed, it will be
necessary to release trapped air in the filter. Carefully
loosen the vent valve counter-clockwise until there is the
hissing sound of air escaping. Once there is a steady
stream of water, close the vent valve, ensuring that the
o-ring does not become pinched.
• T urn the pump onto high speed and re-check for leaks. The
control system will automatically return the pump to low
speed after 15 minutes.
• A
djust the hot tub heat control at the topside panel to the
desired water temperature.
Air Vent Valve
• A
djust water balance (pH, TA, calcium hardness) to
recommended levels and add sanitizor. See section
hot tub water maintenance
• T he hot tub will require 8-10 hours to reach the desired
temperature.
• K
eep insulated safety hard cover on the hot tub, and the
air controls closed during the entire heat up process.
O-ring/ gasket
at union connections
winter drain Plugs
Releasing An Air Lock…
…Through the
pump union
winter Drain Plugs
…Through the
Hose bib
15
Hydropool Self Clean Series Control Systems
north america / Europe
Hydropool Self Clean – Silver & Gold Series
North America
TEMPERATURE CONTROL FUNCTIONALITY
AND ADJUSTMENT
After you manually exit or the system automatically exits
Priming Mode, your hot tub will automatically heat to
the factory preset default temperature of 38˚C (100˚F) The
topside panel will briefly show the default temperature, and
then the display will appear as follows:
Europe
INITIAL START-UP
Note that the water temperature is not
yet displayed, as the system requires
approximately 2 minutes of water flow
through the heater to determine temperature. This is
referred to as ‘polling’ and is indicated on the display by the
icon. After 2 minutes the display will show the current
measured water temperature
Before applying voltage to power-up your hot tub, it is very
important that you understand the sequence of events that occur
when the system is activated in order that the pump can be
primed efficiently and damage to the system can be avoided.
At initial power-up, this display will appear,
and the system will show 4 sets of
numbers in succession (ie. 49 then 63 then
37 then 24). These numbers represent the current software
revision, and the system input voltage.
Press the
pad to increase the temperature to the desired
setting. The Heat indicator light on the Topside Panel will
shimmer for 90 seconds, indicating that the system is not yet
heating, then will illuminate solidly to indicate that the heater
circuit has been energized and the spa water is being heated.
After the initial software indicators are
shown, this display will appear. This display
is indicating that the system is in pump
Priming Mode. This mode will last for 4 to 5 minutes
before automatically exiting and entering the normal
operation mode. You can also manually exit pump Priming
Mode after the pump is primed.
In Standard Operating Mode, the system automatically
activates Pump 1 low speed every 30 minutes for at
least 2 minutes. After 2 minutes, the spa water
temperature is determined. At this point, if the water
temperature is lower than the set temperature, P1 will
continue to run and the Heat indicator light on the
Topside Panel will illuminate. The heater will operate
until the water temperature reaches the set temperature
point, after which, both the heater and Pump 1 low will
automatically turn off.
While in this mode, the heater circuit is disabled to allow
the priming process to be completed without the possibility
of energizing the heater element during low flow or no
flow conditions. The system will not automatically activate
any of the functions, however, by pushing the
pad on
the topside control, the pump can be manually activated to
facilitate priming.
Definition: ‘Priming’ a pump is a term used to describe
the process in which air trapped in the plumbing
and pump wet-end (referred to as an ‘air lock‘)
is released, allowing the pump to move water
efficiently through the plumbing system and to
the jets.
To Check/Change the Set Temperature
The last measured temperature is constantly
displayed on the topside panel. When this
pad is pressed once any time during normal
operation, the display will show the set temperature for
3 seconds. Press this pad a second time to increase or
decrease the set temperature. To change the direction of the
temperature settings (ie. lower vs. raise the temperature),
allow the display to revert back to the current water
temperature then press the
pad again.
PUMP PRIMING MODE
As soon as ‘PR’ is indicated on the topside
panel, push the
pad to start Pump 1
in low speed, then again to switch to high speed
to facilitate priming. See FILLING, CHECKING AND STARTING
YOUR HOT TUB for complete instructions on pump priming.
Once pump priming has been successfully completed, press
the
pad to turn off the pump.
Next, manually exit Priming Mode by pressing the
pad. If you do not manually exit Priming Mode, it will
automatically terminate after 4 to 5 minutes. Be sure that
the pump is primed before exiting this mode.
The temperature can be adjusted from 21˚C (70˚F) to
40˚C (104˚F) in 1˚ increments.
HEater Function
The heater operates with pump low-speed only, and turns
off when ever pump high-speed or blower is activated.
16
PUMP / JETS FUNCTION
MODE FUNCTION
Press this pad to activate the pump
A combination of keypads is used to change hot tub
operation to either ‘STANDARD’, ‘ECONOMY’ or ‘SLEEP’ mode.
1st press – turns on low speed
2nd press – turns on high speed
3rd press – turns off pump
PROGRAMMING Mode Function
Press
then
- the current mode setting will flash
on the display
When low speed is already operating, the 1st press of the
pad puts the pump directly into high speed.
Press
When the blower (optional) is manually activated, the pump
low speed is automatically activated and operates until the
blower times out. If the blower is turned on even briefly,
and then turned back off, low speed will operate for a
minimum of 2 minutes.
ECONOMY MODE
The system will heat to the set temperature only
during the filter cycles. The display will show
when the
temperature is non-current. When the temperature is
current, the display will alternate between
and the
water temperature.
PUMP AUTOMATIC TIME-OUT
High speed
– 15 minutes
Low speed – 4 hours
FILTER CYCLES
SLEEP MODE
The system will heat to within 10˚C (20˚F) of the set
temperature only during filter cycles. The display will show
until the mode is changed.
The system will automatically activate the pump low speed
to filter the water either once or twice each day, and can
be programmed by the user. The first filter cycle begins 6
minutes after the spa is initially powered up. The second
filter cycle begins 12 hours after the start of the first filter
cycle. The filter cycle duration - length of time the pump
low runs - is programmable from 1 to 12 hours (F1 to F12).
The factory default is 2 hours, twice daily.
PROGRAMMING Filter Cycles
To change the factory default filter cycle settings
- the current filter cycle duration will
Press
again to adjust the filter cycle duration
Press
to exit programming mode and save changes.
repeatedly to select mode
STANDARD MODE
The system automatically starts the pump low speed every
30 minutes to measure water temperature, and maintain
the set temperature. The display will show
briefly, then
the last measured water temperature. The current water
temperature is displayed only after the pump has been
operating for at least 2 minutes.
Low speed starts automatically every 30 minutes to measure
water temperature (in STANDARD Mode only – see MODE
FUNCTION), when a filter cycle is activated, or when a
freeze condition is detected.
Press
then
be displayed
then
17
STANDBY / DRAIN ASSIST
LED MOOD LIGHTING
The standby/drain assist feature stops the system from
operating automatically, allowing for convenient filter
cartridge removal and for safe draining of the hot tub. The
following pads must be pressed within 3 seconds of each
other.
Press
then the
pad - the display will
flash
.
Press the
pad on the topside control to start the
selection of LED lighting modes. Pressing the
pad on/off
within 3 seconds cycles through the various ‘light shows’.
When the LED lighting is turned off for more than 5
seconds, then turned back on, the system will resume the
last ‘light show’.
The system will automatically turn off the mood lighting
after 4 hours.
If the system is heating when Standby Mode is activated,
will flash on the display and the pump will continue
to operate for 15 seconds to allow the heater to cool off
before stopping.
All functions will turn off, but the pump low speed can be
activated (by pressing the
pad) to facilitate draining
the hot tub - the display will show DN.
BLOWER OPTIONAL – Factory Installed
Press this pad to turn the blower on and off.
The system will automatically turn off the blower after
15 minutes.
PURGE CYCLES Blower only
The system automatically activates the blower for 30
seconds at the beginning of each filter cycle to introduce
fresh, sanitized water into the blower plumbing circuit.
Press any pad other than the
pad to return the system
to normal operation.
See DRAINING YOUR HOT TUB for detailed instructions.
OZONATOR OPTIONAL
The ozonator operates during FILTER CYCLES only
FREEZE PROTECTION
If the temperature sensor detects a drop to 4˚C (39˚F) within
the heater chamber, the system automatically activates
the pump to provide freeze protection. The pump will
operate until the temperature reaches 5˚C (41˚F) before
returning to normal system mode.
18
Hydropool Self Clean Series Control Systems
north america / Europe
Hydropool Self Clean – Platinum & Titanium Series / Limited & Luxury Edition
PUMP PRIMING MODE
As soon as PRIMING MODE is indicated
on the topside panel, push the left
pad
to start Pump 1 in low speed, then again
to switch to high speed. Push the
center
pad and right
pad to start
Flashing Pump 2 and *Pump 3 respectively
Pump Icon(s)
(*Titanium Series only). These are both
single speed - high only. All of the pumps
will now be operating in high speed to facilitate priming.
See FILLING, CHECKING AND STARTING YOUR HOT TUB for
complete instructions on pump priming.
Platinum, Luxury Edition
Once pump priming has been successfully completed, press
the
pads to turn off the pumps. Next, manually exit
Priming Mode by pressing either the
pad or the
pad. If you do not manually exit Priming Mode, it will
automatically terminate after 4 to 5 minutes. Be sure that
the pumps have been primed before exiting this mode.
Titanium
INITIAL START-UP
Before applying voltage to power-up your hot tub, it is very
important that you understand the sequence of events that
occur when the system is activated in order that the pumps
can be primed efficiently and damage to the pumps can be
avoided.
TEMPERATURE CONTROL
FUNCTIONALITY and Adjustment
After you manually exit or the system automatically exits
Priming Mode, your hot tub will automatically heat to
the factory preset default temperature of 38˚C (100˚F). The
topside panel will briefly show the default temperature, and
then the display will appear as follows:
Note that the water temperature is not
yet displayed, as the system requires
approximately 2 minutes of water flow
through the heater to determine
temperature. This is referred to as ‘polling’
and is indicated on the display by the
Flashing
Pump 1 Low speed Icon
icon. After 2 minutes the display
will show the current measured water
temperature.
At initial power-up, this display will appear,
and the system will show 4 sets of
numbers in succession (ie. 100 then 114
then 28 then 240). These numbers
represent the current software revision,
and the system input voltage.
After the initial software indicators are
shown, this display will appear. This display
is indicating that the system is in pump
Priming Mode. This mode will last for
4 to 5 minutes before automatically
Flashing
exiting and entering the normal
operation mode. You can also manually exit the pump
Priming Mode after the pumps are primed.
Press the
pad to increase the
temperature to the desired setting. The
icon will appear on the display
indicating that the heater has been
activated.
While in this mode, the heater circuit is disabled to
allow the priming process to be completed without
the possibility of energizing the heater element during
low flow or no flow conditions. The system will not
automatically activate any of the functions, however, by
pushing the
pads on the topside control, the pumps
can be manually activated to facilitate priming.
Flashing
Pump 1 Low speed Icon
In Standard Operating Mode, the system automatically
activates Pump 1 low speed every 30 minutes for
at least 2 minutes. After 2 minutes, the spa water
temperature is determined. At this point, if the water
temperature is lower than the set temperature, P1 will
continue to run and the
icon will appear on the
display. The heater will operate until the water temperature
reaches the set temperature point, after which, both the
heater and Pump 1 low will automatically turn off.
Definition: ‘Priming’ a pump is a term used to describe the
process in which air trapped in the plumbing and pump
wet-end (referred to as an ‘air lock‘) is released, allowing
the pump to move water efficiently through the plumbing
system and to the jets.
19
To Check/Change the set temperature
The last measured temperature is constantly
displayed on the topside control. When either of these pads
is pressed once, the display will show the set temperature.
Press either pad a second time to increase or decrease the
set temperature. After 3 seconds the display will once again
show the last measured temperature.
PUMPS AUTOMATIC TIME-OUT
P1 high speed, P2 & P3 – 15 minutes
P1 low speed – 4 hours.
Pump & Blower operating conditions
Platinum Series, Limited & Luxury Edition
P1 and P2 have priority over the blower. If either pump
is on high-speed, the system will not activate the blower
until either pump automatically times-out or is manually
deactivated by the user. Alternately, if only one of the
high-speed pumps is ON and the blower is already ON, when
the second high-speed pump is activated, the blower will
turn OFF.
The temperature can be adjusted from 21˚C (70˚F) to
40˚C (104˚F) in 1˚ increments
Heater Function
Platinum Series, Limited & Luxury Edition: for units
connected to a 16A electrical supply service, the heater
operates only on pump 1 low speed and turns off when
either pump high-speed or blower is activated.
Example 1: If P1 and P2 high-speed are activated at the
same time, and the blower button is pressed 5 minutes later,
the blower will turn ON after a 10 minute delay (balance
of the P1 and P2 high-speed time-outs) and operate for 5
minutes (15 minutes minus 10 minutes)
Titanium Series: for units connected to a 32A electrical
supply service, the heater operates with any 2 high-speed
pumps or 1 high-speed pump and blower.
Example 2: If one high-speed pump (either P1 or P2) and
blower are activated at the same time, and the second
high-speed pump button is pressed 5 minutes later, the
blower will automatically turn OFF, but the system will
continue the time-out countdown. If 5 minutes later, P1
or P2 is manually turned OFF by the user, the blower will
automatically turn ON again and operate for the 5 minutes
remaining before the end of the automatic time-out.
PUMPS / JETS FUNCTION
from left to right on topside control – P1, P2, *P3
(*Titanium series only)
PUMP 1 (P1)
1st press – turns on low speed –
2nd press – turns on high speed –
3rd press – turns off pump
–
the P1 icon
spins slowly
the P1 icon
spins faster
no icon displayed
when P1 is off
CLEAN-UP CYCLE
The Clean-up Cycle begins 30 minutes after the pump(s)
or blower have been turned off or have automatically
timed-out. P1 low speed and the ozonator (optional) will
operate for one hour.
When P1 low is already operating, the 1st press of the P1
pad puts the pump directly into high speed.
SETTING THE SYSTEM CLOCK TIME
Low speed P1 starts automatically every 30 minutes to
measure water temperature (in STANDARD Mode only – see
MODE FUNCTION), when a filter cycle is activated, or when
a freeze condition is detected.
The word TIME flashes on the topside control display upon
initial start-up. This reminder will disappear once the clock
time is programmed.
Press
When P2, P3 or the blower is manually activated, P1 low
speed is automatically activated and operates until the
pump(s) or blower time out. If P2, P3 or the blower is
turned on even briefly, and then turned back off, P1 low will
operate for a minimum of 2 minutes.
PUMP 2 (P2)
1st press – turns on high speed –
2nd press – turns off pump
–
the P2 icon
spins fast
no icon displayed
when P2 is off.
PUMP 3 (P3) – Titanium series
1st press – turns on high speed –
2nd press – turns off pump
–
only
the P3 icon
spins fast
no icon displayed
when P3 is off.
then
To set the hour: Press
time by 1 hour.
Press
to enter programming mode.
or
- each press changes the
to enter, and to continue to set minutes.
To set minutes: Press
time by 1 minute.
or
- each press changes the
Press the
pad again to continue to the filter cycle
programming mode (see below) OR Press the
pad to
exit programming mode.
During normal operation, pressing the
the current time for 3 seconds.
20
pad will display
FILTER CYCLES
Once the system clock time has been programmed, the
system will automatically activate P1 low speed to filter the
water for 2 hours twice each day. During the filter cycle, the
display will show FILTER 1 or FILTER 2.
At this point PROGRAM,
on the display
FILTER 2 and END TIME will appear
Factory preset default
Press the
pad again to enter the filter cycle times into
the system and exit programming mode.
Adjust time as above
‘FILTER 1’ the system automatically activates P1 low to
operate from 8 AM to 10 AM. The filter 1 (F1) LED indicator
on the left side of the topside control panel will light during
filter cycle 1 operation.
The ‘F1’ light on the left side of the topside control panel
will illuminate to indicate that the system is in Filter 1
cycle.
‘FILTER 2’ the system automatically activates P1 low to
operate from 8 PM to 10 PM. The filter 2 (F2) LED indicator
on the left side of the topside control panel will light during
filter cycle 2 operation.
The ‘F2’ light on the left side of the topside control panel
will illuminate to indicate that the system is in Filter 2
cycle.
PROGRAMMING Filter Cycles
To change the factory default filter cycle settings
Press
then
then
then
within three
seconds.
PURGE CYCLES
The system automatically activates P2, P3 and the blower
for 30 seconds at the beginning of each filter cycle
to introduce fresh, sanitized water into these plumbing
circuits.
(You will already have advanced to this point if you pressed
after completing the SETTING THE SYSTEM CLOCK TIME
sequence)
MODE FUNCTION
At this point PROGRAM,
appear on the display
To set the hour: Press
time by 1 hour.
Press
or
STANDARD MODE
The system automatically starts P1 low speed every 30
minutes to measure water temperature, and maintain the
set temperature. The word STANDARD will remain on the
display along with the last measured temperature. The
current water temperature is displayed only after the pump
has been operating for at least 2 minutes.
- each press changes the
to enter, and to proceed
ECONOMY MODE
FILTER 1 and END TIME will appear The system will heat to the set temperature only during the
To set the hour: Press
time by 1 hour.
filter cycles. The display will show the word ECONOMY.
or
STANDARD-In-ECONOMY MODE
While the system is in Economy Mode, pressing any
pad or the
pad will cause the system to activate
Standard Mode for 1 hour, after which the system will
revert back to Economy Mode. Pressing the
pad during this time will put the system back into Economy Mode
immediately.
- each press changes the
to enter, and to continue to set minutes
To set minutes: Press
time by 5 minutes
Press
- each press changes the
to enter, and to continue to set minutes.
At this point PROGRAM,
on the display
Press
FILTER 1 and START TIME will
or
To set minutes: Press
time by 5 minutes
Press
This pad is used to change hot tub operation to either
STANDARD, ECONOMY or SLEEP mode. Press
to enter mode
programming and press
to select the desired mode.
The LCD will flash until
is pressed again to confirm the
selection.
or
- each press changes the
SLEEP MODE
The system will heat to within 10˚C (20˚F) below the set
temperature only during filter cycles. The display will show
the word SLEEP.
to enter, and to proceed
At this point PROGRAM,
appear on the display
Adjust time as above Press
FILTER 2 and START TIME will
to enter, and to proceed
21
STANDBY / DRAIN ASSIST
LIQUID CRYSTAL DISPLAY (LCD)
The standby/drain assist feature stops the system from
operating automatically, allowing for convenient filter
cartridge removal and for safe draining of the hot tub. The
following pads must be pressed within 3 seconds of each
other.
Continually provides feedback on the operating status of
the hot tub. Icons indicate various functions and programming information.
LCD INVERT
This feature inverts the LCD readout for convenient viewing
from inside the hot tub. To invert the readout,
Platinum Series: press
Titanium Series: press
or
The system will automatically exit Standy Mode after 1
hour and resume normal operating functions.
Press
then the P2
pad and the display will flash:
SBY
(Platinum series)
STANDBY
(Titanium series)
If the system is heating when Standby Mode is activated,
will flash on the display and the pump will continue
to operate for 15 seconds to allow the heater to cool off
before stopping.
All functions will turn off, but P1 low speed can be
activated (by pressing the P1
pad) to facilitate draining
the hot tub and the display will show
(Platinum series)
DRAINING
(Titanium series)
then
To return the LCD readout to normal viewing (from outside
of the hot tub), repeat.
Topside Panel Lock Features
TEMPERATURE LOCK
The temperature lock feature prevents unauthorized
temperature adjustment of the hot tub water. When the
temperature lock is activated, all automatic functions will
continue to operate normally.
The following pads must be pressed within 3 seconds of
each other to activate the lock:
then
then P1
Press any pad other than the P1
pad to return the system to
normal operation. See section DRAINING YOUR HOT TUB for
detailed instructions.
then
TEMPERATURE Unlock
The following pads must be pressed within 3 seconds of
each other to deactivate the lock:
then
then P1
LED MOOD LIGHTING
Press the
pad on the topside control to start the
selection of LED lighting modes. Pressing the
pad
on/off within 3 seconds cycles through the various ‘light
shows’. When the LED lighting is turned off for more than 5
seconds, then turned back on, the system will resume the
last ‘light show’. The system will automatically turn off the
mood lighting after 4 hours.
then
When locked, the TL (Temperature Lock) light on the left side
of the topside control panel will illuminate. Only the topside
control panel temperature pads will be deactivated.
TOPSIDE PANEL Full LOCK
The topside panel lock feature prevents unauthorized use of
the hot tub controls. When the topside control panel lock is
activated, all automatic functions will continue to operate
normally.
BLOWER OPTIONAL – Factory Installed
The following pads must be pressed within 3 seconds of
each other to activate the lock:
OZONATOR OPTIONAL
then P1
Press this pad to turn the blower on and off.
The system will automatically turn off the blower after
15 minutes.
The ozonator operates during FILTER CYCLES and CLEAN UP
CYCLES only. The display will show the O3 icon while the
ozonator is operating.
Pressing any pad on the topside control panel will suspend
ozonator function for 1 hour.
then
TOPSIDE PANEL Unlock
The following pads must be pressed within 3 seconds of
each other to deactivate the lock:
then P1
FREEZE PROTECTION
If the temperature sensor detects a drop to 4˚C (39˚F) within
the heater chamber, the system automatically activates
the pumps to provide freeze protection. The pumps will
operate until the temperature reaches 5˚C (41˚F) before
returning to normal system mode.
then
When locked, the PL light (Panel Lock) on the left side of
the topside control panel will illuminate. All of the topside
control panel pads will be deactivated except for the
pad.
22
Topside Panel Display Messages
/
/
/
/
(solid)
Overheat – Spa has shut down. One of the sensors has
detected 48˚C (119˚F) at the heater.
Spa has shut down – sensor plugged into Sensor ‘B’ port
not working.
/
DO NOT ENTER WATER! Remove cover and allow water to
cool. Reset system by pressing any topside control panel
pad. If system does not reset, shut off power and call your
dealer.
Sensors are out of balance – If topside display alternates
between temperature and SNS, then occurrence may be
temporary and will correct itself. The spa shuts down
completely when the SNS message is flashing on the
display.
POSSIBLE CAUSES OF OVERHEATING
• filter cycle too long or overlapping
(pump running for extended periods of time)
• isolation/gate valves partially closed
• extremely hot weather/high ambient temperatures
• defective sensor wire
/
/
/
A substantial difference in temperature between the
sensors has been detected – this could indicate a flow
problem. Check water level in spa and add if necessary. If
water level is okay, make sure that pumps are primed and
all gate valves are fully opened.
/
(flashing)
Overheat – Spa has shut down. One of the sensors has
detected that the spa water is 44.5˚C (112˚F).
/
Persistent low flow problem – displays on the fifth
occurrence of an HFL message within a 24 hour
period. Heater circuit is deactivated but other spa functions
continue to operate normally. Check water level in spa and
add if necessary. If water level is okay, make sure that pumps
are primed and all gate valves are fully opened. Press any
topside panel pad to reset.
DO NOT ENTER WATER! Remove cover and allow water
to cool. At 42˚C (107˚F) the system should automatically
reset. If system does not reset, shut off power and call your
dealer.
POSSIBLE CAUSES OF OVERHEATING
• filter cycle too long or overlapping
(pump running for extended periods of time)
• isolation/gate valves partially closed
• extremely hot weather/high ambient temperatures
• defective sensor wire
/
Potential freeze condition detected. Pumps and blower
will automatically activate when temperature drops to 4˚C
(39˚F) regardless of operation mode.
/
Spa has shut down – sensor plugged into Sensor ‘A’ port
not working.
23
Topside Panel Display Messages Continued
/
/
Inadequate water detected in heater chamber - Check
water level in spa and add if necessary. If water level is okay,
make sure that pumps are primed and all gate valves are
fully opened. Press any topside panel pad to reset.
Allows for convenient draining of the spa using the P1 low
speed. Can only be accessed while in Standby mode. Press
any topside control pad except for P1 to return to normal
operation mode.
/
/
Inadequate water detected in heater chamber – displays on
third occurrence of a dr message within a 24 hour period.
The spa shuts down completely when the drY message is
flashing on the display. Check water level in spa and add
if necessary. If water level is okay, make sure that pumps
are primed and all gate valves are fully opened. Press any
topside panel pad to reset.
System is operating in Standard mode. See section
Hydropool Self Clean Control Systems for complete details.
/
System is operating in Economy mode. See section
Hydropool Self Clean Control Systems for complete details.
/
System is operating in Standard-in-Economy mode.
See section Hydropool Self Clean Control Systems for
complete details.
Priming mode – occurs when spa is first powered up, or
when power has been restored after a power interruption.
Allows for safe priming of the pumps. See section Hydropool
Self Clean Control Systems for complete details.
/
--- / --F / --C
System is operating in SLEEP mode. See section Hydropool
Self Clean Control Systems for complete details.
--- / ----
If spa water temperature is more than 7˚C (20˚F) cooler than
the set temperature, the system will automatically activate
the heater to provide freeze protection. This is a normal
function; no corrective action is necessary.
Temperature unknown – after the pump has been
operating for 2 minutes, the current water temperature will
be displayed.
Temperature not current while in Economy or Sleep mode
– In either of these modes, the pump may be off for hours
in between filter cycles. To view the current spa water
temperature, either switch to Standard mode or turn on the
pump for at least 2 minutes.
/
/
Stops the control system from operating automatically to
allow filter cartridge removal. Press any topside control pad
except for P1 to return to normal operation mode.
24
JET and FEATURE OPERATION
Air Injector*
Wrist/thigh Jet
Poly Storm
Directional
Poly Storm
Twin Roto
Ozone Jet*
(Hydropool Series)
Poly Storm
Massage
Adjustable
Neck Jet
Reflexology Jet
Mini Storm
Directional
Power Storm
Twin Roto
Mini Storm
Twin Roto
Power Storm
Massage
Mini Storm
Massage
Power Storm
Multi-massage
* indicates a non-adjustable jet
JET WATER FLOW ADJUSTMENT
Your Hydropool hot tub features adjustable water flow on
specific hydrotherapy jets.
All Hydropool hot tubs are shipped from the factory with
the jets in the open position.
To reduce the flow: grasp the outer flange of the jet, and
turn clockwise approximately a 1/4 turn. When it hits
the stop, the jet is considered closed, and flow will be
restricted.
Interchanging jet inserts
A great feature for custom tailoring the jets in your
Hydropool hot tub to suit your personal hydrotherapy
needs. Jets of like size and dimension may be interchanged
with each other, for example, if you wished to swap a Poly
Storm Directional jet for a Poly Storm Twin Roto jet, or a
Mini Storm Twin Roto jet for a Mini Storm Directional jet.
To increase the flow: from the closed position, turn the jet
counter-clockwise approximately 1/4 turn. When it hits the
stop, the jet is open, and there is maximum jet flow. Do not
attempt to turn the jet past the stop, as this will unclip the
jet internal from the socket.
JET AIR FLOW ADJUSTMENT
Your Hydropool hot tub features adjustable air flow on
specific hydrotherapy jets.
To reduce the flow: turn the handle on the air control
clockwise. When it hits the stop, the air is closed, and
air flow will be restricted.
To increase the flow: turn the handle on the air control
counter-clockwise. When it hits the stop, the air control is
fully opened.
For maximum operating efficiency, the air controls must
remain closed when your hot tub is not in use.
25
Jet Insert removal & Replacement
Poly/mini storm directional & twin roto
Power storm massage & twin roto
To Remove:
• Turn the jet conter-clockwise to unclip & pull out of socket.
To Re-install: ­
• Push the jet into the socket until it snaps into place, ensuring the
square pin on the back of the jet lines-up with the groove in the
socket flange.
DIVERTER VALVE
When your HYDROPOOL hot tub is equipped with a diverter valve,
it allows you to direct the flow of the water so that it increases the
power of the jets on the CAPTAINS CHAIR or on the LOUNGER, or a
combination of the two. Simply turn the valve left or right.
TURN
Always: return the valve handle to the middle position before
exiting the hot tub to ensure that there is air and water flow
to the ozone jet and ice-bucket/filter-niche drains for proper
performance.
WATERFALL CONTROL optional
If your hot tub was ordered with the optional waterfall feature, then you will have a waterfall flow control valve. The
waterfall feature was designed to provide a gentle cascade of water over the neck and shoulder area. Simply turn the top
of the control clockwise for less water flow, and counterclockwise for more water flow.
26
Hydropool Surround Sound audio & Audio/Video Systems
Quick-Start Guide
General
Power ON/OFF..................................................................................35
Screen Saver....................................................................................35
Insert & Eject a DVD........................................................................35
Input Source Selection...................................................................35
Mute...................................................................................................35
Video Format (PAL/NTSC)...............................................................35
Listening to the Radio......................................................................28
Playing a CD......................................................................................28
Watching a DVD...............................................................................28
am/fm CD Player and MP3 Docking Station
Overview of Controls.......................................................................29
Remote Control Key Map................................................................29
DVD Player Function
Play, Pause........................................................................................35
Fast Fwd/Back, Next/Previous.......................................................35
Display, Title, Subtitle......................................................................35
Angle, Zoom......................................................................................35
Goto, Clear.........................................................................................35
Repeat, A – B....................................................................................35
PBC, Random, Program (VCDs).....................................................35
General
Power ON/OFF..................................................................................30
Opening & Closing Front panel......................................................30
Input Source Selection...................................................................30
Clock – Setting & Viewing..............................................................30
Audio Control
Adjusting Volume..............................................................................30
Mute...................................................................................................30
Bass Level.........................................................................................30
Treble Level.......................................................................................30
Balance Adjustment........................................................................30
Fader Adjustment.............................................................................31
LCD MONITOR
Overview of Controls & Remote Control
Key Map.............................................................................................36
On Screen Menu Language...........................................................36
System Setup Menu.........................................................................37
Monitor Tuner Controls
North American Tuners...................................................................38
European Tuners..............................................................................38
Radio Function
Selecting Band & Storing Presets................................................31
Setting Station Presets Automatically..........................................31
Seek & Manual Tune.......................................................................31
Scan....................................................................................................31
Preset Station Scan.........................................................................31
Local/Distance Function.................................................................31
Hydropool Optional Waterproof Remote Overview...............39
Hydropool AM/FM CD Player
Optional Waterproof Remote.......................................................40
CD Player Function
Insert, Play & Eject a CD.................................................................32
Changing CD Tracks & Music Seek..............................................32
Intro, Scan, Random & Repeat......................................................32
Hydropool DVD Player
Optional Waterproof Remote.......................................................41
Hydropool LCD Monitor
Optional Waterproof Remote.......................................................42
Audio and MP3 Docking Station
Docking your audio/MP3.................................................................32
Hydropool Monitor Tuner
Optional Waterproof Remote.......................................................43
DVD Player
Overview of Controls.......................................................................33
Remote Control Key Map................................................................33
System Setup Menu.........................................................................34
27
HYDROPOOL SURROUND SOUND™ AUDIO/VIDEO SYSTEM
QUICK-START GUIDE
For all Hydropool Hot Tubs with optional HYDROPOOL SURROUND SOUND™ systems
AM/FM CD Player
The following info is a guide to the basic system functions of
the HYDROPOOL SURROUND SOUND ™ audio/video system
package.
4
TURNING AM/FM CD PLAYER ON/OFF
5
6
7
8
9
10
• Press the POWER button 3 to turn on and
off power to the AM/FM CD player
MRD 60
MARINE
SOURCE
LISTENING TO THE RADIO
• Press the SOURCE button 4 to cycle through available
program sources: TUNER -> CD -> AU-1 If there is no CD
inserted, then the CD source will not appear
• When TUNER is selected, station frequency will be
indicated on the display
• Use the TUNE/SEEK-UP button 13 and the
• TUNE/SEEK-DOWN button 14 to select station
3
2
1
LOCAL
SET
DISC IN
POWER
11
SCAN
INTRO
1
MUTE
RANDOM R E P E AT
3
2
4
DISC
–
5
AUDIO
+
6
TUNE
12
BAND
AUTO
21 20 19 18
17 16 15 14 13
LISTENING TO A CD
• Open the front panel by pressing down the
FRONT PANEL RELEASE button 7
• Insert a CD into the disc slot with the label facing up and
close the front panel
• The CD plays automatically after loading
WATCHING A DVD
CD Player
1
10 8
6
15 16 17 2
EJECT
POWER
On the LCD Monitor *:
• Press the POWER button on the TV remote
• Press the TV/Video button on the TV remote until
‘S-VIDEO’ appears on the screen
DISC
PLAY/PAUSE STOP
AV1
AV2
L
VIDEO
AUDIO R
CONTROLS
PREVIOUS
On the DVD player:
• Press the POWER button 1 on the front of the DVD
player or on the DVD remote
• Insert a DVD into the disc slot with the label facing up
• DVD playback will begin automatically after the disc is
inserted. With some DVD discs, you will need to press the
PLAY button 10 on the DVD player or the remote to begin
playback.
NEXT
12 9 7
SOURCE
5
MENU
3
ENTER
13 14
11
LCD MONITOR
VIDEO
On the AM/FM CD Player:
• Press the SOURCE button 4 to cycle through available
program sources. Select AU-1
* Note: the Monitor can only be operated using the factory IR
remote or the Hydropool Universal IR Remote
LED power indicator
28
4
HYDROPOOL SURROUND SOUND AM/FM CD PLAYER
OVERVIEW OF CONTROLS
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.
17.
18.
19.
20.
21.
Volume control
Mute
Power ON/OFF
Source
IR receiver
Preset buttons 1 – 6
Front panel release
Display
Clock set
Local
Scan
Band
Tune/seek up
Tune/seek down
Disc +
Auto
Disc -
CD repeat
CD random
Audio
CD intro
4
5
6
7
8
MRD 60
9
10
MARINE
SOURCE
3
2
1
LOCAL
SET
DISC IN
POWER
SCAN
INTRO
1
MUTE
RANDOM R E P E AT
3
2
–
5
4
AUDIO
21
20
DISC
+
6
TUNE
BAND
AUTO
19
17
18
16
15
14
13
IR REMOTE CONTROL KEY MAP
Basic functions can be controlled via the AM/FM CD player or the IR remote control
1. Power ON/OFF
2. Volume Zone 1
3. Mute
4. Source
5. Band
6. Tune/seek up
7. Tune/seek down
8. Auto
9. CD repeat
10. Audio
11. Intro
12. Random
13. Disc – (not applicable)
14. Disc + (not applicable)
15. Amp Source (not applicable)
16. Pause
17. SNC (not applicable)
Hot Tub Control Functions
18.
19.
20.
21.
22.
Pump 1 (P1)
Pump 2 (P2)
Pump 3 (P3)
Light
Blower
3
6
11
8
1
7
12
4
2
9
10
15
5
16
17
13
18
22
21
19
14
20
29
11
12
AM/FM CD PLAYER CONTROLS
SETTING the CLOCK
1 Press and hold the SET button for 2 seconds, until the first
digit of the time starts flashing
2 Use the TUNE/SEEK-UP or TUNE/SEEK-DOWN buttons to
adjust the hour. Note the AM/PM indicator at the left
when setting the hour
3 Press SET again to select the minutes. Adjust as above
4 Press the SET button one final time to save the input and
complete setting time
5 The system will automatically return to clock mode, and
the time will appear after 3 seconds
IMPORTANT USER SAFETY INSTRUCTIONS
CAUTION – Risk of Electric Shock
• Do not leave compartment door open
• Replace components only with identical components
• Do not operate the audio/video equipment controls while
inside the spa. Use the IR remote control(s) provided
AUDIO CONTROL
WARNING – Prevent Electrocution
• Do not connect auxiliary components to the system
• Do not service this product yourself as opening or
removing covers may expose you to dangerous voltage or
other risk of injury. Refer all servicing to qualified service
personnel
• If water enters any electrical equipment compartment
area, or if there are other indications of potential damage
to the unit, turn off the unit and refer servicing to
qualified service personnel
• This unit should be subjected to periodic routine
maintenance to ensure that it is operating properly
ADJUSTING the VOLUME
1 Controls volume for the AM/FM radio/CD player, and also
for the TV and DVD player
2 Rotate VOLUME knob to increase or decrease volume
(0-31)
3 Current volume setting is momentarily indicated on the
display
4 When watching TV or viewing a DVD: set the volume
level to ‘15’ and use the TV volume to control sound
levels
MUTE
1 Press the MUTE button once to mute the sound. ‘MUTE’
will flash on the display
2 Press the MUTE button again or rotate the volume knob
to resume audio
General
POWER ON/OFF
1 Press the POWER button on system or IR remote once to
turn system ON, and once to turn system OFF.
2 NOTE: The radio power must be turned on in order to turn
on power to the DVD player and the LCD TV.
BASS LEVEL
1 Press the AUDIO button until ‘BAS’ appears on the
display
2 Rotate the VOLUME knob to adjust setting. ‘C-0’
indicates neutral bass setting (factory default); -2 to -12
indicates reduced bass; +2 to +12 indicates increased
bass
3 Unit will automatically return to volume mode if an input
is not detected for 3 seconds
OPENING and CLOSING the FRONT PANEL
1 OPEN: Place thumb on the front panel release button,
and forefinger below the front panel overhang. Firmly
depress the release button while gently pulling the front
panel
2 CLOSE: flip up front panel and press firmly until you hear
an audible click
3 Except when changing the CD, keep the front panel
closed at all times to prevent water intrusion that could
cause damage to the system
TREBLE LEVEL
1 Press the AUDIO button until ‘TRE’ appears on the
display
2 Rotate the VOLUME knob to adjust setting. ‘C-0’ indicates
neutral treble setting (factory default); -2 to -12
indicates reduced treble; +2 to +12 indicates increased
treble
3 Unit will automatically return to volume mode if an input
is not detected for 3 seconds
INPUT SOURCE SELECTION
1 Press the SOURCE button to cycle through available input
sources. Sequence is TUNER -> CD -> AU-1
2 If a CD is not inserted into the CD player, that input
source will not appear on the display. Sequence is
TUNER -> AU-1
BALANCE ADJUSTMENT
1 Press the AUDIO button until ‘BAL’ appears on the
display
2 Rotate the VOLUME knob to adjust setting. ‘C-0’
indicates center (factory default); R1 to R15 indicates
right balance; L1 to L15 indicates left balance
3 Unit will automatically return to volume mode if an input
is not detected for 3 seconds
CLOCK
VIEWING the CLOCK
1 Press the SET button to toggle the display between clock
and radio mode. Unit will automatically display clock
time whenever radio controls are not being used
30
AM/FM CD PLAYER CONTROLS
FADER ADJUSTMENT
1 Press the AUDIO button until ‘FADE’ appears on the
display
2 Rotate the VOLUME knob to adjust setting. ‘C-0’
indicates center (factory default); R1 to R15 indicates
rear fade; F1 to F15 indicates left balance
3 Unit will automatically return to volume mode if an input
is not detected for 3 seconds
SEEK and MANUAL TUNE
1 Press the TUNE/SEEK-UP or TUNE/SEEK-DOWN button
once to automatically tune to the next strongest higher
or lower station signal (auto seek)
2 To manually tune to a station signal, press and hold
either TUNE/SEEK button for 2 seconds. Holding the
button down will either increase or decrease through the
station frequencies manually
3 When the desired frequency is reached, release the TUNE/
SEEK button. The system remains in manual tune for 3
seconds after the last button is released, so that you can
still fine tune with additional button presses
4 After 3 seconds the system will return to auto seek
mode
RADIO FUNCTION
Press the SOURCE button to select Radio mode. Station
frequency will be displayed
SELECTING BAND and STORING STATION PRESETS
1 Press the BAND button to cycle through the 5 sets of
radio bands. Sequence is FM1 -> FM2 -> FM3 -> AM1 ->
AM2. Each band stores up to 6 independent presets, for a
total of 18 FM and 12 AM presets
2 To program a preset: tune into the desired station, press
and hold for 2 seconds the numeric button that will be
used to store this preset. ‘PX’, where X represents the
preset number, will be displayed on the bottom right of
the display (i.e. P6)
3 If power to the hot tub is interrupted, or the reset
switch is pressed, the station presets will need to be
reprogrammed
SCAN FUNCTION
1 Select any FM or AM band set and press SCAN to listen to
a few seconds of each radio station. The display will flash,
and the system will automatically advance to the next
available station signal, play that radio station for a few
seconds, then advance to the next available station, etc,
etc. To stop scanning and continue listening to the
current station, press the SCAN button again
2 The radio remains in scan mode until the SCAN button is
pressed a second time or one of the TUNE/SEEK buttons
is pressed
PRESET SCAN FUNCTION
1 Select any FM or AM band set and press AUTO to listen
to a few seconds of each radio station preset. The display
will flash the preset station number (i.e. P4), and the
system will automatically advance to the next preset
station signal, play that radio station for a few seconds,
then advance to the next preset station signal, etc, etc. To
stop scanning and continue listening to the current
station, press the AUTO button again
2 The radio remains in preset scan mode until the AUTO
button is pressed a second time or one of the preset
buttons is pressed
SETTING STATION PRESETS AUTOMATICALLY
1 To automatically program the station presets: press a
preset button (1-6) – the system will start the
programming sequence at this preset button first
2 Hold the AUTO button for 2 seconds, or until the
programming sequence begins
3 The current preset and additional presets up to P6 will be
programmed with the next available station signal
4 When the auto preset cycle is complete, the unit will
remain in preset scan mode (see PRESET SCAN FUNCTION),
and will continue scanning the programmed presets until
the AUTO button is pressed
5 To select only the strongest station signals, press the
LOCAL button
6 All 18 FM and 12 AM presets can be stored sequentially
by pressing the BAND button to enter the next band set
(i.e. If you started with FM1 preset buttons, pressing the
BAND button will step to FM2) and continuing auto
programming
LOCAL/DISTANCE FUNCTION
1 Press the LOCAL button to select between local station
mode and any station (default) mode. When ‘LOCAL’ is
displayed, only the strongest station signals will be
selected during SEEK or SCAN mode.
2 In the default mode (‘LOCAL’ not shown on display),
all usable stations with sufficient signal strength will be
selected during SEEK or SCAN mode
31
AM/FM CD PLAYER CONTROLS and mp3 docking station
CD PLAYER FUNCTION
INTRO SCAN, RANDOM and REPEAT
1 Intro Scan: press the INTRO button to select Intro Scan
Mode, and ‘SCN’ will appear to the left on the display. The
first 10 seconds of each track on the CD will play. To exit
Intro Scan Mode, press the INTRO button a second time,
or the TUNE/SEEK-UP or TUNE/SEEK-DOWN button
2 Random: press the RANDOM button to play the CD tracks
in a random order, and ‘RDM’ will appear to the left on
the display. To exit Random Mode, press the RANDOM
button a second time
3 Repeat: press the REPEAT button to repeat playback of
the current track, and ‘RPT’ will appear to the left on the
display. To exit Repeat Mode, press the REPEAT button a
second time
INSERT, PLAY and EJECT a CD
1 To insert a CD: open the front panel and insert a CD into
the slot with the CD label facing up. The CD will be drawn
inside the unit. Close the front panel. The system will
automatically switch to the CD source mode, and the
‘DISC IN’ symbol on the display indicates that a CD is in
the drive.
2 Play: CD playback will begin automatically. The display
will show the current track number and the play time of
that track. An animated 3-D rotating disc will also show
on the display to indicate that a disc is playing
3 To remove a CD: open the front panel and press the CD
(eject) button on the inside left of the front panel.
Remove CD from the drive, and close the panel.
AUDIO AND MP3 DOCKING STATION
DOCKING YOUR AUDIO/MP3
The Docking Station is compatible with all alternate audio
sources such as MP3 players.
To install any audio source:
1 Locate and open the Docking Station door by gently
pulling upward on the handle.
2 Remove the connector cover prior to plugging in your
audio source. Always keep the cover on when the docking
station is not in use.
3 Center the device over the Docking Station Adaptor and
connect.
4 For stand alone unit that do not have a stereo head unit,
make sure to turn on the switch located inside to power
the amplifier before you begin.
5 Close the Docking Station door once you have begun
using your device.
CAUTION: listen for an audible click to indicate that
the front panel has been securely closed to prevent
water intrusion that could cause damage to the system
CHANGING CD TRACKS and MUSIC SEEK
1 To advance to the next track: press the TUNE/SEEK-UP
button once, and the track counter will advance one
track. When the final track on the CD is reached, the next
press of the button will return to the first track
2 To fast forward or rewind through tracks: press and hold
the TUNE/SEEK-UP or TUNE/SEEK-DOWN button.
Releasing the button will stop the process and playback
will start from that point in the track
3 To return to the beginning of the current track: press the
TUNE/SEEK-DOWN button once at any time during track
playback. Pressing the TUNE/SEEK-DOWN button a
second time within 1 second will skip back to the
previous track
32
HYDROPOOL SURROUND SOUND DVD PLAYER
OVERVIEW OF CONTROLS
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.
17.
Power
Eject
Menu
IR receiver
Source
Disc Slot
Next
Stop
Previous
Play / Pause
Video / Audio input
Reset
Cursor buttons
Enter
Indicator light for DISC
Indicator light for AV1
Indicator light for AV2
1
10 8
6
15
16 17
2
EJECT
POWER
DISC
PLAY/PAUSE STOP
VIDEO
AV1
AV2
L
4
AUDIO R
CONTROLS
PREVIOUS
12
9
NEXT
7
SOURCE
5
MENU
ENTER
3
13 14
11
IR REMOTE CONTROL KEY MAP
Basic functions can be controlled via the DVD player or IR remote control
All advanced functions can only be accessed via the IR remote control
1. Power
2. Eject
1
23
3. Mute
4. Subtitle
5. Angle
6. Display
POWER
7. Source
8. Setup
ZOOM
MUTE
9. PAL/NTSC
3
10. GOTO
24
RESUME
SHUFFLE
11. Title
25
12. Menu
11
A-B
REPEAT
13. Cursor buttons
14. Enter
27
15. Slow Fwd / Back
28
GOTO
PROGRAM
16. Play
26
17. Fast Fwd / Back
10
18. Next
19
19. Stop
16
20. Pause
1
2
21. 0 – 9
22. Clear
23. Zoom
4
5
21
24. PBC
25. Random
7
8
26. Program
CLEAR
27. Repeat
22
0
28. A – B
33
6
9
2
DISPLAY
PBC
EJECT
P/N
SOURCE
7
SUB-T
ANGLE
5
TITLE
SETUP
ENTER
4
8
14
13
MENU
12
20
3
18
6
17
9
-/--
10+
SLOW
15
DVD Player Controls
SYSTEM SETUP MENU: ON SCREEN MENUS and DISPLAYS – overview
Press the...
1. …STOP button before proceeding (only if a DVD is playing)
2. …SETUP button to display the main system setup menu
3. …CURSOR buttons to navigate the sub-menus
4. …ENTER button to make selection
GENERAL MENU -- MAIN PAGE
-- GENERAL PAGE --
-- GENERAL PAGE --
GENERAL SETUP
TV DISPLAY
NORMAL/PS
TV DISPLAY
SPEAKER SETUP
PIC MODE
NORMAL/LB
PIC MODE
AUTO
AUDIO SETUP
ANGLE MARK
WIDE
ANGLE MARK
HI-RES
PREFERENCES
OSD LANG
OSD LANG
N-FLICKER
CAPTIONS
CAPTIONS
SCR SAVER
SCR SAVER
EXIT SETUP
MAIN PAGE
GENERAL SETUP
MAIN PAGE
GENERAL SETUP
GENERAL SETUP
-- SPEAKER SETUP PAGE -LT/RT
DOWNMIX
-- GENERAL PAGE -TV DISPLAY
PIC MODE
STEREO
MAIN PAGE
ANGLE MARK
ON
OSD LANG
OFF
CAPTIONS
DISPLAY
POWER
SCR SAVER
EJECT
MAIN PAGE
LOUD SPEAKERS SETUP
MUTE
ZOOM
PBC
SHUFFLE
RESUME
SUB-T
P/N
ANGLE MARK ON/OFF
SOURCE
ANGLE
-- AUDIO SETUP --
REPEAT
A-B
TITLE
SETUP
-- GENERAL PAGE --
ANALOG
AUDIO OUT
TV DISPLAY
DYNAMIC
PIC MODE
MAIN PAGE
OSD LANG
ANGLE MARK
PROGRAM
GOTO
ENGLISH
CAPTIONS
ENTER
SCR SAVER
MAIN PAGE
MENU
1
4
7
2
5
8
3
AUDIO OUT
–
–
DYNAMIC
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
MAIN PAGE
9
- --
0
SET OSD LANGUAGE
-- AUDIO SETUP --
6
/
CLEAR
AUDIO RELATED
10+
SLOW
DYNAMIC RANGE COMPRESSION
-- GENERAL PAGE --
FULL
TV DISPLAY
6/8
PIC MODE
4/8
OSD LANG
ANGLE MARK
2/8
OFF
CAPTIONS
ON
SCR SAVER
OFF
MAIN PAGE
CLOSED CAPTION
-- GENERAL PAGE -TV DISPLAY
PIC MODE
ANGLE MARK
OSD LANG
CAPTIONS
SCR SAVER
MAIN PAGE
SCREEN SAVER
34
ON
OFF
DVD Player CONTROLS
General
3 Fast Fwd / Back: press the
or
button during
playback. Each time the button is pressed, the fast
forward/back speed changes as follows:
DVD – normal -> 2x -> 4x -> 6x -> 8x -> 20x
VCD – normal -> 2x -> 4x -> 6x -> 8x
4 Next / Previous: press the
button to jump to the
next chapter (DVD) or the next track (VCD/CD), and press
the
button to jump to the previous chapter or
track
POWER ON/OFF
1 Press the POWER button on system or IR remote once
to turn system ON, and once to turn system OFF. If there
is already a disc in the drive, playback will start
automatically.
2 NOTE: Power to the AM/FM CD player must
be ON in order to turn ON the DVD player
SCREEN SAVER
1 If there is no button input detected for 5 minutes, the
screen saver begins automatically
2 The screen saver can be turned ON/OFF in the SETUP
menu under ‘Screen Saver’
DISPLAY, TITLE, SUBTITLE
1 Display: press the DISPLAY button on the IR remote to
show statistical disc information during playback
(chapter, time remaining, counter etc.)
2 Title: press the TITLE button on the IR remote to display
the DVD disc title (not available on all DVD discs)
3 Subtitle: press the SUBTITLE button on the IR remote to
turn on/off subtitle, and/or to select subtitle language on
DVD discs with multilingual subtitle options
INSERT and EJECT a DVD
1 To insert a DVD: insert a DVD into the slot with the label
facing up. The DVD will be drawn inside the unit. ‘DISC
LOADING’ will show on the TV display indicating that
a DVD is in the drive. Note: DVD playback will begin
automatically
2 To remove a DVD: press the EJECT button on the front
panel. Remove DVD from the drive
ANGLE, ZOOM
1 Press the ANGLE button on the IR remote to change the
view angle (only available on DVDs that have the
multi-angle feature)
2 Press the ZOOM button on the IR remote to increase the
size of the picture. Note that in ‘ZOOM’ mode, only the
enlarged part of the picture will be viewable; the entire
picture will not be visible
CAUTION: always ensure the component panel door has
been securely closed to prevent water intrusion that
could cause damage to the system
INPUT SOURCE SELECTION
1 Press the SOURCE button to cycle through available input
sources. Sequence is DISC -> AV1 -> AV2
GOTO, CLEAR
1 Press the GOTO button to select DVD playback chapter
using the 0-9 number buttons
2 Press the CLEAR button to clear a number that was
entered in error
MUTE
1 Press the MUTE button on the DVD player IR remote, and
the word ‘MUTE’ will appear momentarily on the TV
screen to indicate that the DVD audio is in mute mode.
Press the MUTE button again to exit DVD audio mute
mode, and the words ‘MUTE OFF’ will appear momentarily
on the TV screen
Note: Use of the DVD mute function is generally not
required, as the sound volume is muted through either
the LCD TV function or the Radio function
REPEAT, A – B
1 Press the REPEAT button on the IR remote to select
either repeat chapter in current view, or repeat title.
On-screen sequence is CHAPTER REPEAT ON -> TITLE
REPEAT ON -> REPEAT OFF
2 Press the A – B button on the IR remote to select and
repeat a particular scene or passage. On-screen sequence
is A TO B SET A -> A TO B SET B -> A TO B CANCELLED
PAL/NTSC
1 Press the P/N button on the IR remote to select the DVD
video playback format:
NTSC – North American video format
PAL – European video format
PBC, RANDOM, PROGRAM (VIDEO CD only)
1 Video CDs with PBC (playback control) can be played with
or without a menu. On the IR remote, press the PBC
button to select
2 Press the RANDOM button on the IR remote to play tracks
in random order
3 Press the PROGRAM button to select and program the
order in which to play tracks
DVD PLAYER FUNCTION
PLAY, PAUSE, FAST FWD/BACK, NEXT/PREVIOUS
1 Play: playback begins automatically after disc is inserted.
In most cases it will go to the DVD root menu, and it will
be necessary to press the PLAY or ENTER button
2 Pause: press the button during playback to freeze the
picture (still mode). Press the button again to resume
playback
35
HYDROPOOL SURROUND SOUND LCD MONITOR
OVERVIEW OF CONTROLS and IR REMOTE KEY MAP
All functions are accessed with the IR remote control
1
2
3
4
5
6
7
8
9
10
11
12
13
TV/VIDEO Press repeatedly to cycle source selection between VIDEO,
S-VIDEO, YCbCr (Component Video) & PC
VOLUME Thes two buttoms are primarily used in conjunction
with the MENU & PICTURE buttons.
TV MENU Press to show the on-screen menu. Press repeatedly to cycle
through the available menu items & to clear the menu from the screen.
ENTER Used in conjunction with disc and setup menus.
LEFT
RIGHT Used in conjunction with disc and setup menus.
PICTURE Press to call up the on screen Picture Menu.
Press the CH / button to cycle through Contrast, Brightness,
Sharpness, Color, Tint. The selected item will be displayed in blue.
Adjust the desired item with the Volume buttons.
STATUS Press repeatedly to cycle between a user-adjustable
picture and three different preset picture balance settings.
MUTE Press to reduce sound to minimum level. Press again to restore.
POWER Press to turn the LCD monitor on/off.
DISPLAY Press to display information about the current
Program source & SLEEP TIMER setting.
CHANNEL UP / DOWN Press to select menu items with
some on-screen menus
CCD Press repeatedly to cycle between Closed Captions 1,
Closed Captions 2, Text 1, Text 2 and off.
SLEEP Sets the sleep timer to automatically power off the monitor.
ON SCREEN MENU LANGUAGE SELECTION
1
Not
Applicable
3
10
2
11
4
5
12
6
7
13
8
Not
Applicable
The onscreen display language is selected as follows:
FUNCTION
1.
2.
3.
4.
LANGUAGE
OSD Position
OSD Color
Melody
Wide
CCD
Press the TV/MENU button
CH / button to reach LANGUAGE mode in FUNCTION.
Press the VOLUME + button to select desired language
Press the TV/MENU button to exit
All of the on screen displays will appear in the selected language
Move ± : Sel.
36
9
English
Mode 1
Mode 1
On
On
Off
:Prev.
LCD MOnitor Controls
SYSTEM SETUP MENU: ON SCREEN MENUS and DISPLAYS – overview
Press the...
1. ...TV/MENU button to display the main system setup menu
2. ...CH / button to select sub-menus: Picture, Sound, Time, Function
3. ...VOL +/- to select and adjust an option
MENU
Picture
Sound
Time
Function
Move ± : Sel.
SOUND
Sound mode
Equalizer
Balance
Surround
Move ± : Sel.
FUNCTION
Standard
LANGUAGE
OSD Position
OSD Color
Melody
Wide
CCD
0
Off
:Prev.
Move ± : Sel.
PICTURE
Contrast
Brightness
Sharpness
Color
Tint
Move ± : Sel.
:Exit
English
Mode 1
Mode 1
On
On
Off
:Prev.
TIME
32
25
25
25
0
Clock
Timer
On time
Off time
:Prev.
Move ± : Sel.
37
AM12:00
Off
AM12:00
AM12:00
:Prev.
MONITOR Tuner Controls
North american Tuners
2
1. Power on/off
2. Selects broadcast input between Air/CATV
3. CH / to select TV channels
4. Press to scan TV channels into memory automatically
5. Press to select channel directly
6. +/- to add or erase channels from memory
1
3
4
5
6
European Tuners
1. Power on/off
2. Menu: (AV mode only) Push to access on-screen menu.
Use CH-/+ button to select item. Use VOL+/- button to adjust item.
3. Press AVC to select input mode: TV, AV1, AV2.
4. Press to scan channels into memory automatically
5. Press CH-/+ to select TV channels
6. Press Vol+/- to adjust sound level
7. Mute: sound on/off
POWER
MUTE
1
3
7
AVC
AUTO
CH +
2
Note: Volume and Mute buttons are disabled in AV mode.
5
VOL +
6
VOL –
MENU
5
CH –
38
4
6
Hydropool Optional waterproof Remote overview
LED (red light) blinks to indicate that the
remote control is sending a signal
POWER - turns on/off the selected
home entertainment component
SETUP - use for all factory
programming sequences
Press TV, VCR/DVD or CD once
to select a component to control
GUIDE - displays program guide
EXIT - to exit an on-screen menu/guide
CURSOR ARROWS - for navigating menu/guide
SELECT – to choose option
INFO - displays current channel and program
information
MENU - displays an on-screen menu
VOL – controls sound volume
CH – selects channel
MUTE – turns sound off/on
LAST – recalls the last channel, also
used to page back one screen in the
main menu
Controls available spa functions
Keypad - directly selects channels
Mode – switches between DVD
and TV, and will also control input
select feature on most TV models
Enter - press once to enter selection
REW, PLAY, FF, REC, STOP and PAUSE used to control CD and DVD functions
39
HYDROPOOL AM/FM CD PLAYER OPTIONAL WATERPROOF REMOTE
FUNCTION CROSS-REFERENCE
STANDARD NON-WATERPROOF REMOTE
(included)
HYDROPOOL UNIVERSAL WATERPROOF REMOTE
(optional)
FUNCTIONS
Power ON/OFF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . CD + Power
Volume control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . VOL /
Mute . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Mute
Source . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Select
Band . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Enter
Tune/seek up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . FF
Tune/seek down . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . REW
Auto . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Mode
CD repeat . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Play
Audio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Record
40
HYDROPOOL DVD PLAYER OPTIONAL WATERPROOF REMOTE
FUNCTION CROSS-REFERENCE
STANDARD NON-WATERPROOF REMOTE
(included)
DISPLAY
POWER
HYDROPOOL UNIVERSAL WATERPROOF REMOTE
(optional)
EJECT
MUTE
ZOOM
PBC
P/N
SOURCE
SHUFFLE
RESUME
SUB-T
ANGLE
REPEAT
A-B
TITLE
SETUP
PROGRAM
GOTO
ENTER
MENU
1
2
3
4
5
6
7
8
9
-/--
CLEAR
0
SLOW
10+
FUNCTIONS
Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . VCR/DVD + Power
Eject . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Enter
Mute . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Mute
Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Info
Source . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Mode
Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Exit
Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Menu
Cursor arrows . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Cursor arrows
Enter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Select
Play . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Play
Rapid FWD / BACK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .FF
/ REW
Skip NEXT / PREV . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . CH /
Stop . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Stop
Pause . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Pause
Numbers 0 - 9 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Numbers 0 - 9
41
HYDROPOOL LCD monitor OPTIONAL WATERPROOF REMOTE
FUNCTION CROSS-REFERENCE
STANDARD NON-WATERPROOF REMOTE
(included)
HYDROPOOL UNIVERSAL WATERPROOF REMOTE
(optional)
FUNCTIONS
Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Mute . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Numbers 0 – 9 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TV/AV . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CH (channel UP/DN) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Menu navigation cursors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Enter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
VOL (volume UP/DN) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Sleep . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CCD. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Picture . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
42
TV + Power
Mute
Numbers 0 - 9
Mode
Menu
CH /
Cursor arrows
Select
VOL /
Record
Stop
Guide
Exit
Info
HYDROPOOL MONITOR Tuner OPTIONAL WATERPROOF REMOTE
FUNCTION CROSS-REFERENCE
STANDARD NON-WATERPROOF REMOTE
(included)
HYDROPOOL UNIVERSAL WATERPROOF REMOTE
(optional)
North America
Europe
POWER
MUTE
AVC
AUTO
CH +
VOL +
VOL –
MENU
CH –
FUNCTIONS
Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Mute (EU only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Numbers 0 - 9 (NA only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
AIR/CATV (NA) / AVC (EU) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Auto-PRGM (NA) / Menu (EU) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CH (channel UP/DN) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Menu navigation cursors (EU only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Menu (EU only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
VOL (volume UP/DN) (EU only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Auto (EU only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Add/Erase (NA only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
43
CBL/SAT + Power
Mute
Numbers 0 - 9
Mode
Menu
CH /
Cursor arrows
Select
VOL /
Guide
Last
HOT TUB WATER BALANCE – GENERAL OVERVIEW
NOTABLE POINTS
• T he reliability and longevity of your hot tub support
equipment are directly related to how well water
quality is maintained!
• The small volume of water in your hot tub is easily
affected by the introduction of oils, lotions, perspiration
and chemicals. It is imperative that you give your
hot tub regular attention to maintain clean, safe and
balanced water to prevent premature damage and/or failure
(corrosion/calcification) to the support equipment.
Maintaining proper hot tub water balance and sanitizer
levels is extremely important. Neglected hot water will
allow bacteria to quickly spread.
• The mineral content of hot tub water increases due to
water evaporation, sanitizers and other chemicals. If the
mineral concentration, particularly calcium, becomes too
high, the minerals will literally “drop” or precipitate out
of the water and deposit on the hot tub walls, plumbing,
jets, in the filter and on the heater element.
• It is very important that pH be checked frequently and
maintained in the recommended range as indicated
in the chart water balance summary for your
Hot Tub
• It is also very important that Total Alkalinity (the ability of
the water to resist a change in pH) be maintained in the
recommended range as indicated in the chart water
balance summary for your Hot Tub
• Although there may be two identical hot tub models
right next door to each other, the maintenance requirements will be different, dependant on such factors as:
– bather load
– frequency of use/quantity of bathers
– different body chemistry
– sun vs. shade
– temperature
CHEMICAL Handling
SAFETY HINTS
•Never pre-mix chemicals with each other prior
to adding to hot tub water.
• Add only one chemical to the water at a time.
• Always add chemicals to water and not vice-versa.
•Chemicals may be corrosive, so handle with care and
store in a cool dark place.
• Never smoke near chemicals as most are flammable
•Ensure any spilled chemicals are carefully cleaned up
immediately.
•Always have the Poison Control telephone number
handy in the event of an emergency.
• Keep chemicals out of children‘s reach
• Wear safety glasses and gloves when handling
chemicals.
INITIAL Water FILL & Balance
1 Make sure the hot tub water is circulating.
2 Add a sequesterant (stain and scale controller). Allow
water to circulate for an hour before adding anything
else to the hot tub water.
3 Add a Shock / oxidizing agent .
4 Add sanitizing tablets (Bromine or Chlorine) to the dispenser:
• Built in dispenser: if your
Hydropool hot tub was
ordered with the optional
built in bromine/chlorine dispenser, (located in the lid of
the cartridge filter housing),
refer to section CARTRIDGE
FILTER for details on removDISPEnSER
CHECK
ing and re-installing the lid.
VALVE
Once the filter lid is removed,
ASSEMBLY
you’ll notice a clear 2.5 cm
(1”) diameter tube extending
from the bottom of the lid.
Unscrew the check valve
assembly at the end of the tube and add 5 or 6 tablets. Do
not overfill dispenser as performance will be affected. Set
the dial initially to ‘5’, and allow water to circulate for 3
to 4 hours before testing level. Adjust dial more or less as
necessary.
For these reasons, it is very important to develop proper
hot tub water maintenance habits and follow your
Hydropool retailer’s recommended water maintenance
procedures.
eater and other component failure
H
due to improperly maintained pH or
Total Alkalinity is not covered under
warranty.
• Floating dispenser: As above, add 6 or 7 tablets, adjust
initially to ‘5’, allow water to circulate for 3 to 4 hours,
then test.
The tablets will dissolve slowly over a 10-14 day period,
depending on dial setting, and use of the hot tub.
5 Test pH and Total Alkalinity and adjust accordingly.
44
GLOSSARY OF COMMON WATER MAINTENANCE TERMS
1 C
HLORINE – in granular, liquid or puck/tablet form, is an oxidant and biocidal agent. It is very effective and fast acting.
Recommended chlorine residual level is 3.0 to 5.0 ppm.
2 CHLORAMINES – a compound formed when chlorine combines with nitrogen or ammonia present in the water. When
allowed to go unchecked, it causes eye and skin irritation and is indicated by a strong chlorine odour.
3 ONE-PART BROMINE – also available in puck/tablet form, is another type of oxidant/biocidal agent, and is introduced
into the hot tub water via a brominator. Recommended bromine residual level is 3.0 to 5.0 ppm
4 TWO-PART BROMINE – composed of a liquid or powder component introduced manually into the water on a weekly
basis, and a granular component that is added daily or as the hot tub is used.
5 BROMAMINES – are formed when bromine destroys nitrogen-bearing organic matter. Unlike chloramines, bromamines
don’t cause eye irritation, however, when allowed to go unchecked, will cause an objectionable odour.
6 SHOCK – the practice of adding an oxidizing agent to hot tub water to destroy ammonia, nitrogenous and organic
contaminants (chloramines and bromamines)
7 pH – a logarithmic value expressing the relative acidity or basicity of a substance (such as hot tub water) as indicated
by the hydrogen ion concentration. pH is expressed as a number on a scale of 0 to 14, where 0 is most acidic, 1 to 7
being acidic, 7 considered neutral, 7 to 14 being basic, and 14 being most basic. The ideal range for hot tub water is
7.4 to 7.6 ppm
8 pH INCREASER – raises the pH level of the water.
9 pH DECREASER – lowers the pH level of the water.
10 TOTAL ALKALINITY (TA) – the amount of carbonate, bicarbonate and hydroxide compounds present in the water that
determines the ability or capacity of the water to resist change in pH. Also known as the ‘buffering’ capacity.
11 ALKALINITY BOOSTER – raises the alkalinity.
12 CALCIUM HARDNESS – the calcium portion of the total alkalinity which represents 70 to 75% of total hardness.
Calcium concentrations determine whether water is ‘soft’ - too little calcium, or ‘hard’ -too much calcium.
13 CALCIUM BOOSTER – increases the calcium level.
14 TOTAL DISSOLVED SOLIDS (TDS) – a measure of the total amount of dissolved matter in the water (calcium, carbonates,
bicarbonates, magnesium, metallic compounds, etc.)
15 SEQUESTERANTS (STAIN AND SCALE CONTROLLERS) – keeps dissolved metals and minerals in the water from
attacking the hot tub shell and support equipment components.
16 DEFOAMER – removes foam build-up from the water surface. At best, this is a temporary remedy, as excessive foam is
merely a symptom of improper water balance (typically high organic residue and/or high pH).
17 CARTRIDGE FILTER CLEANER – degreases and cleans cartridge filters.
18 OZONATOR – generates Ozone (a gaseous molecule composed of 3 atoms of oxygen) and is injected into the hot tub
water for the oxidation of water contaminants.
19 TEST KIT – used to monitor specific chemical residual or demands in the water. May be in the form of litmus strips or
liquid drops.
20 PPM – abbreviation for ‘parts per million’, the unit of measurement used in chemical testing which indicates the parts
by weight in relation to one million parts by weight of water. Essentially identical to the term mg/L - milligrams per
liter.
WATER BALANCE SUMMARY FOR YOUR HOT TUB*
SANITIZER (ppm)
Chlorine
Bromine
MIN
1.0
2.0
IDEAL
3.0 - 5.0
3.0 - 5.0
MAX
10.0
10.0
CHEMICAL
PH
7.2
7.4 - 7.6
7.8
Total Alkalinity (TA)
80
80 - 120
180
Total Dissolved Solids (TDS)
300
1000 - 2000
3000
Calcium Hardness
150 200 - 400
500 - 1000
* National Spa & Pool Institute recommended levels for residential spas/hot tubs
45
Water Balance Troubleshooting
PROBLEM
POSSIBLE CAUSES
SOLUTIONS
cloudy water
microscopic particles too small to filter Test and adjust all water balance elements and add
out
flocculent* to cause the particles to combine together
so they can be filtered out
high Total Alkalinity
Test these water balance elements and adjust to
recommended parameters.
high pH levels
high Calcium Hardness
scale
high Calcium Hardness
(white/grayish deposit)
Test calcium hardness level and treat with sequesting
agent* or perform partial drain/refill.
skin/eye irritation
improper pH and/or Total Alkalinity Test water balance and make the appropriate
levels
adjustments.
excessive foam
buildup of body oils or cosmetics
If no water line is present you can try using defoamer*
to break up the contaminants and then a clarifier* to
help filter them away. If a water line is present the spa
may need to be drained and cleaned. Either way, the
filter should be thoroughly cleaned by soaking over
night in bleach. An oil absorbing sponge can help in
preventing this in the future.
Laundry detergent residual in
swimwear
Prevent by running an extra rinse cycle on washing
machine or re-rinse well by hand.
excess organic contaminants
Some organic matter is prone to causing foamy
water as it breaks down in the filter (maple leaves
especially). Generally using defoamer* to break up
the contaminants, then a clarifier* to help filter them
away followed by thoroughly cleaning your filter will
clear up the problem. It may however be necessary
to drain and refill your spa if the foaming is quite
excessive.
low Calcium Hardness
Test calcium hardness and if necessary increase with
calcium chloride*
corrosion/etching
low Calcium Hardness and/or low Total Test calcium hardness and if necessary increase with
Alkalinity
calcium Chloride*
discoloured water
(clear v. turbid water)
presence of metals in water
(iron, copper, etc)
Treat with chelating* or sequestering agent*
unstable pH
low Total Alkalinity levels
Test total alkalinity levels and if necessary increase
with sodium bicarbonate*
pH resistant
to changing
high Total Alkalinity levels
Test total alkalinity levels and if necessary decrease
with sodium bisulfate* or muriatic acid*
* contact your local Hydropool retailer for specific product recommendation
46
Corona Discharge Ozone Technology
All Hydropool hot tubs are factory prepared to accommodate
ozonators. The Hydropool Corona Discharge Ozonator is
regarded as the most technologically advanced system on the
market, allowing longer contact time with the hot tub water
resulting in reduced chemical consumption and clearer, cleaner
water. Hydropool’s unique ozone injection system both maximizes
the dispersion of the ozone gas and decreases the bubble size
resulting in longer contact with the water and increased water
quality and purity. The ozone/water mixture is sent down a
series of tubes where the ozone is “broken down” into even
smaller bubbles before being re-mixed with the water reducing
the “off-gassing” commonly found with other ozone systems.
Hot Tub
Water
CD Ozonator
Mazzei
Ozone Injector
Ozone Mixing
Chamber
Ozone
Injector Jet
Routine Hot Tub Maintenance
QUARTERLY
1D
rain hot tub at least once per quarter and clean the
acrylic shell surface with a non-abrasive cleaner designed
specifically for acrylic surfaces. See sections changing
the hot tub water and draining your hot tub
review Chemical handling
safety hints
CLEANING THE SKIMMER BASKET
DAILY
1 Activate the standby/drain assist mode
2 Remove the skimmer basket by pulling the weir door
forward, and pulling the basket up and towards the
front
3 Remove debris from basket. (Note: Avoid hitting the
basket against objects to knock debris loose as this may
damage the unit)
4 Reinsert basket
5 Take the system out of standby/drain assist mode, and
as the pump begins to operate, monitor water flow over
the weir door to assure that it is free floating
1 Test water, and if necessary, add shock.
2 Ensure proper water level is maintained.
WEEKLY
1
2
3
4
Test pH and Alkalinity. Adjust accordingly
Top-up chemical dispenser
Add sequesterant (stain and scale controller)
Remove and spray cartridge filter with garden hose and
re-install (see section CARTRIDGE FILTER)
5 Remove and clean out skimmer basket (see section
CLEANING THE SKIMMER BASKET)
6 Add Shock / oxidizing agent
7 Inspect union connections for o-ring and gasket leaks Tighten if loose
MONTHLY
1 S oak your filter cartridge in a filter cartridge cleaning
solution. Rinse thoroughly and, if possible, allow to dry
before re-installing. Hydropool recommends purchasing a
second filter so that while the first is cleaning, the other
is clean and ready to install
47
CARTRIDGE FILTER
Locking Ring
The cartridge should be cleaned every two to four weeks,
depending on the amount of use. Signs that the filter
requires cleaning include:
• Reduced jet power
• Hazy gray water
• Rattling noise in the pump or filter
• Heater not working
Air Vent Valve
Filter Lid
CHECK VALVE
ASSEMBLY
Built in Chemical
dispenser
Removal
1 Activate the standby/drain assist mode.
2 Remove the filter cover and open the small, black air
vent/bleeder valve on the top of the filter lid.
3 Press down the lock tab to disengage and turn the
locking ring counter clockwise.
4 Pull the filter lid upwards, and lift the cartridge element
straight up and out of filter housing.
LOCK TAB
Cartridge filter
element
Cleaning
Filter Housing
5 With a garden hose and spray nozzle, hose off the cartridge
element, ensuring to carefully separate every pleat.
CLEANING THE ACRYLIC SURFACE
6 To remove collected lotions, body oils, etc. soak the
The acrylic surface can be cleaned and polished using a
cartridge in warm water and a filter cleaning/emulsifying
soft cloth and acrylic cleaner, available at your Hydropool
compound (available at your HYDROPOOL retailer).
retailer.
7 A cleaning cylinder may be purchased from your
HYDROPOOL Hot tub retailer.
•Important: Do not use detergents 8 Rinse thoroughly and dry before replacing.
the remaining residues will adversely
9 Hydropool recomends purchasing a spare filter cartridge so
affect water chemistry, making it
that you always have a clean substitute ready to rotate.
difficult to maintain proper water
10 After the element has dried - if necessary, lightly brush
balance
between pleats with a fine paint-brush to remove
•Do Not use abrasive cleaners remaining dirt particles.
damage to the acrylic surface will occur.
Do not use a wire brush or other
devise to clean cartridge element.
Do not put in dishwasher or washing
machine.
SAFETY HARD COVER
When a hot tub is uncovered, over 90% of heat is lost
from the water surface. This evaporation also affects the
chemical balance and could create humidity problems
indoors. HYDROPOOL Safety Hard Covers are engineered
for maximum thermal efficiency and appearance. They
are hinged in the middle for easier handling, and the zip
fastener allows the tapered foam inserts to be changed
if damaged. The skirt of the safety hard cover hugs the
lip of the hot tub for a tight fit. The handles are placed
so that even one person can easily carry a large cover.
The locks, with one part fastened to the deck or skirt,
prevent small children or animals from entering the hot
tub. Do not drag the safety hard cover across the hot tub or
decking. Fold the cover first, then lift by the handles.
Standing on the hardcover could cause the tapered foam
inserts to crack, which will lead to water absorption.
Re-installation
11 Place the cartridge filter back into the filter housing.
12 Replace the filter housing lid, pushing it down to seat,
ensuring that the lid o-ring does not become twisted.
13 Hydropool recomends that the lid o-ring be lubricated
with a non-petroleum based lubricant (ie. Silicone gel)
when it becomes dry. This will help to prevent
twisting and pinching as the lid is installed, and
significantly increase longevity of the o-ring.
14 Install the filter lock-ring, turning clockwise until the lock
tab snaps into place.
15 Close the air vent/bleeder valve.
16 Take the system out of standby/drain assist mode.
17 When the pump starts circulating on low speed, it will be
NEVER LEAN OR STAND ON YOUR HARDCOVER.
necessary to release trapped air in the filter. Carefully
loosen the air vent/bleeder valve counter-clockwise until
The cover should be cleaned at least twice a year with a
there is the hissing sound of air escaping. Once there is a
vinyl moisturizer and protector.
steady stream of water, close the vent valve, ensuring that
the o-ring does not become pinched.
48
CHANGING THE HOT TUB WATER
11 To completely flush the old water from the plumbing
lines: allow fresh water to fill into the foot-well area
while the old water continues to be pumped out.
Always keep at least 10cm (4 in.) of water in the
foot-well so that pump 1 remains primed.
12 When the water from the drain hose turns clear
(indicating fresh fill water), flush is complete.
13 Turn off the low speed pump.
14 Close the drain-hose bib on the hot tub plumbing line
and continue filling hot tub with fresh water.
15 Place cover on hot tub (to avoid splash-out).
16 Open pump 1 return gate valve.
17 Press any button on the topside control panel (other
than the pump 1 button) to take the system out of
Standby/drain assist mode. Pump 1 low speed and
the heater will activate to circulate and heat the water
while filling continues. This also reduces the possibility
of an airlock occuring.
18 Continue adding fresh fill water until level is
approximately 19mm (3/4 in.) from the top of the
skimmer opening.
19 Once fill is complete, remove the #10 rubber expansion
plug from the bottom of the skimmer housing.*
20 If the filter housing was opened to replace the cartridge
filter, it will be nessesary to release trapped air from the
filter housing by carefully loosening the small black air
vent/bleeder valve located on the top of the filter housing.
When water begins to escape close the air vent valve.
21 In the unlikely event of a pump air lock (pump 1 is
operating but there is no water movement from the
jets), refer to section PUMP PRIMING/RELEASING AN
AIR LOCK
A hot tub should be drained every 8-12 weeks, depending
on size and amount of use. If your hot tub is used daily or
by a large number of bathers, the water should be drained
more often. One method to determine the approximate
length of time between water changes is to divide the
water volume (in liters) of your hot tub by 13.5 and then
divide by the average number of bathers each day.
(
Formula ________ ÷ 13.5
Volume of water
in litres
) ÷ (__________) = (__________)
Average
daily bathers
Days
between
water
changes
Example:
1000 liters divided by 13.5 divided by 2 = 37 days.
The hot tub water must be changed when the amount of
dissolved solids becomes excessive, and is usually indicated
by “gray” or dull looking water.
DRAINING YOUR HOT TUB
Hydropool Exclusive Quick-drain™ & fill
refer to diagram
Overview
• Requires the use of 2 garden hoses - drain hose and
fill hose
• While first garden hose is draining old water from
hot tub…
• …second hose is used to wash down interior surface of
the hot tub and for fresh water fill.
* It may be necessary to put system into Standby/Drain
ASSIST mode in order to remove plug.
refer to Figure 1 & Figure 2
1
Locate nearest drain facility (shower, laundry tub, floor
drain, lawn, etc.).
2 Put the hot tub control system into standby/drain
assist mode. The system will automatically exit
Standy Mode after 1 hour and resume normal
operating functions.
3 Remove the skimmer basket so that the hole beneath
it is accessible, and insert the #10 rubber expansion
plug provided.
4 Attach garden hose to hose bib located on plumbing line
beside the hot tub control system.
5 Run garden hose to drain location.
6 Open hose bib.
7 Close pump1 return gate valve next to the hose bib (this
directs the water out the drain hose).
8 Activate the low speed pump.
9 Monitor the hot tub while it drains.
10 Use the second garden hose to wash down interior
surface as the hot tub continues to drain. A sponge may
also be used to wipe down the interior surface.
P1 Gate Valve
Figure 1
WATER SOFTENERS
Hose bib
Figure 2
Never fill a hot tub with water from a water softener, as
it could adversely effect the water chemistry, making it
difficult to maintain proper water balance. If you live in
an area with hard or soft water, give careful attention to
your Calcium Hardness level. Topping up with soft water
is acceptable.
49
Hydropool Exclusive Quick-drain™ & fill
#10 Skimmer Plug
Fill Hose
Drain Hose
Gate Valve
Hose Bib
Skimmer/Pre-filter
Heater
pump
Closing Pump 1 return Gate Valve
50
Cabinet Wing-Locks
The high quality wing-locks provided on your Hydropool
Hot Tub cabinet not only firmly secure the equipment
access panel, they also serve as convenient handles for
removal and replacement. In order to maintain optimum
performance and extended life, Hydropool recommends
lubricating twice annually with a silicone based lubricant.
Recommended product: Super-Lube silicone based
lubricant (or equivalent). Available at major retailers.
Caution: Do not use a petroleum based lubricant, as this will cause premature
deterioration of the lock seal.
Lubrication point
PROTECTING YOUR CABINET WOOD FINISH
HYDROPOOL hot tub cabinets are made from Western cedar
and are factory stained. Once stained, cedar weathers well,
and with proper care will maintain its beauty for many
years. For a protective translucent finish and to enhance the
wood grain beauty use Sikkens Cetol 01 #077
stain or equivalent. A polyurethane or marine varathane
with UV inhibitors is also highly recommended. These
protective finishes stabilize the wood grain and build
a durable, breathable water-repellent barrier between
the wood surface and the elements. These products are
available from your local building supply center.
GAZEBOS
If you are mounting, or planning to mount a gazebo over the top of your hot tub, it is critical to ensure that Hydropool
is aware of this, as extra supports may be necessary. Otherwise, it will be necessary for your installer to add the extra
supports where required.
51
WINTERIZING YOUR HYDROPOOL HOT TUB
In the event that you do not wish to use your hot tub
year-round, it is very important that you properly winterize
to protect against damage from freezing. Your HYDROPOOL
retailer can perform this service for a nominal fee. If you
choose to winterize your hot tub yourself, please follow the
directions outlined below:
• Cover exposed plumbing connections with plastic bags
and duct tape.
• Where practical, disconnect hot tub support equipment
and store in a dry heated area.
• Install the safety hardcover, and cover the entire hot tub
with a tarp to prevent premature weathering of the cabinet
and the safety hard cover.
• Remove snow build up regularly to prevent damage to the
safety hard cover.
• It is assumed that your HYDROPOOL hot tub has been
properly installed on a reinforced concrete pad to
eliminate lifting of the hot tub due to hydrostatic ground
water pressure.
• Drain the hot tub entirely see section - DRAINING YOUR
HOT TUB
• Remove and clean the cartridge filter element see
section - CARTRIDGE FILTER
• Using a wet/dry utility vacuum, remove remaining water
from the jet openings, filter cartridge housing, and footwell.
• Either pour or use a turkey-baster where necessary to
add potable biodegradable RV antifreeze to areas such
as pump wet end, jet channels, filter housing, blower
channels. Do not use automotive antifreeze.
• Important: mixing potable biodegradable RV antifreeze
with water significantly reduces its ability to protect
against freezing. Therefore, it is very important ALL
water is removed from the hot tub plumbing before
adding.
• Add potable RV antifreeze to the holes in the bottom
suction/drain to prevent any trapped water in the false
floor from freezing and damaging the hot tub shell.
• Turn pump on for only a few seconds to circulate the
antifreeze.
• Unthread and disconnect all unions in the support
equipment area. Remove lowest winter drain plug
on pump face plate. Repeat for all pumps, where
applicable.
If you are not 100% confident that
your hot tub is properly winterized, please
consult your authorized HYDROPOOL Hot
Tub Retailer. Caution recommends that an
authorized Hydropool Retailer winterize
your
hot tub in the initial year. Damage
as a result of freezing is not covered by
the warranty.
winter Drain Plugs
52
GENERAL TROUBLESHOOTING
Electrical/Mechanical
SYMPTOM
POSSIBLE REASON(S)
ACTION
No Power
–
–
–
–
G.F.C.I. Trip
– Short or ground in system
– Faulty G.F.C.I. – As above-contact qualified electrician or your
Hydropool retailer
No Circulation
–
–
–
–
–
–
–
–
Jet Surge
– Water level too low
– Blockage in plumbing lines
– Suction gate valve partially closed
– Add water to correct level
– Check gate valves and/or skimmer basket
– Pull gate valve handle “up” all the way
No Heat or
Erratic Heat
–
–
–
–
–
–
–
–
–
–
Noisy Motor
– Damaged or worn bearings
–
– Low voltage
–
– Low water level
–
– Frozen pump
–
Digital Top Side
No Longer Displays
– Improper connection
– Electrical brown-out
Digital Temperature
Display is Erratic
or Flashing
– Water temperature has
– Decrease filter cycle and or add cold water.
exceeded set point If condition continues contact Hydropool retailer
Breaker off at main panel or fuse out –
Improper wiring
Fuse blown in control
G.F.C.I. tripped
Pump is not primed (air lock)
Gate valves are closed
Water level is too low
Skimmer obstructed or closed
Cartridge filter requires cleaning
Blockage in plumbing line
Suction / Return valve partially closed
low water level
Faulty sensor
Verify that breaker and/or GFCI are on
If there is still no power,
contact your Hydropool retailer or a
qualified electrician
See Pump Priming/Release an Air Lock
Open gate valves
Top up water to proper level
See Cleaning Skimmer Basket
Clean & reinstall
Contact your Hydropool retailer
Ensure valves are open
Top up water level
Contact your Hydropool retailer
Contact your Hydropool retailer or a
qualified electrician
Contact qualified electrician
Top up water level
Thaw out
– Contact your Hydropool retailer
– Reset GFCI OFF/ON
53
GENERAL TROUBLESHOOTING Continued
WHAT TO DO IN THE EVENT OF...
…Power Failure or sYstem fault during
Cold Weather Conditions
…POWER FLUCTUATIONS
The power supply into your home is, for the most part, fairly
consistent. However, when local power demand is high,
there is a tendency for the voltage entering your home to
drop (sometimes significantly) or fluctuate. This condition is
referred to as a ‘brown-out’. Although safeguards have been
built into the system to protect against this condition, supply
voltage may drop low enough, if even for a second, to cause
the system to display a ‘ghost’ message. Should this occur
or if the display shows partial messages, try resetting the
system by turning power to the hot tub off, waiting a few
minutes, then turning power on again. If this does not reset the
system, contact your local Hydropool retailer or service
organization.
If your control system will not reset, (ie. GFCI trips) or if
your pump will not circulate for any other reason, place
a low wattage space heater under the cabinet in the
equipment area. This will delay the risk of freezing while
a service appointment is scheduled.
Always follow the manufacturers
instructions when locating and placing
a portable electric space heater into
service. Ensure that safe clearance to
combustible surfaces is maintained.
Do not leave unattended.
Notes:
54
Notes:
55
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement