ClearSounds | Quattro | Troubleshooting guide | ClearSounds Quattro Troubleshooting guide

ClearSounds Quattro Troubleshooting guide
ENGLISH
ESpAñoL
FRANÇAIS
CSC48
Operating Manual
ClearSounds® QUATTRO
Bluetooth Amplified Stereo
Neckloop
Accessory
V508
1 – ENGLISH
TABLE OF CONTENTS
PRIOR TO USE
Pg. 3............. Congratulations
Pg. 4-5.......... Important Safety Instructions
Pg. 6-7.......... Location of Controls
INSTALLATION & SET UP
Pg. 8............. Parts checklist
Pg. 8-9.......... Charging
Pg. 10........... Power ON and Off
Pg. 10........... Wearing
FUNCTIONS
Pg. 11-12..... Pairing to a cell phone
Pg. 12-13..... Pairing to additional devices
Pg. 13-14..... Adjusting Volume
Pg. 14-15..... Marking and Receiving Calls
Pg. 16........... LED Indicator
Pg. 17........... Audio Tones
Pg. 17-18..... Stereo Audio Listening
TROUBLESHOOTING GUIDE
Pg. 18
TECHNICAL SPECIFICATIONS
pg. 19
WARRANTY POLICY
Pg. 20-21
2 – ENGLISH
PRIOR TO USE
Congratulations on your purchase of the QUATTRO Amplified
Neckloop from ClearSounds Communications®. Please read
this User Manual carefully in order to get the best use out of
your new accessory. Keep this manual safe for easy reference.
Please visit our website at www.clearsounds.com to register
your product, download additional manuals and review troubleshooting tips.
Be sure to save your sales receipt as your proof of purchase
should you need warranty service. The serial number for this
product is located on the backside of the unit.
The QUATTRO generates an amplified induction (loop) signal
that is picked up by the telecoil of your hearing aid(s) or
cochlear implant processor(s). This option in the hearing
device is activated by setting the hearing aid(s) or cochlear
processor to the “T” or “MT” position. The QUATTRO has been
developed to facilitate the use of a Bluetooth capable cellular
phone, landline phone, or audio device including stereo audio
devices with a t-coil equipped hearing device for hands-free
wireless operation. The QUATTRO now also accommodates a
3.5mm headset jack for users without t-coils, hearing aids, or
cochlear implants to enjoy the same hands-free functionality
of this stereo device by using a regular 3.5mm headset
or ear buds.
Warranty Service – This product is designed to provide years
of quality service. However, if there is a malfunction and the
troubleshooting recommendations on page 18 do not resolve
the problem, follow the warranty procedure on page 20.
3 – ENGLISH
█ IMPORTANT SAFETY INSTRUCTIONS
This product is a mobile solution built on Bluetooth technology.
Please read and understand the Installation Guide and User
Manual before using your QUATTRO.
Electromagnetic Interference/Compatibility: Nearly every
electronic device is susceptible to electromagnetic interference
(EMI) if inadequately shielded, designed, or otherwise
configured for electromagnetic compatibility.
Facilities: To avoid electromagnetic interference and/or
compatibility conflicts, turn off your QUATTRO in any facility
where posted notices instruct you to do so. Hospitals or health
care facilities may be using equipment that is sensitive to
external RF energy.
Aircraft: When instructed to do so, turn off your device when
on board an aircraft. Any use of a device must be in accordance
with applicable regulations per airline crew instructions.
Medical Devices: If you use any personal medical devices,
consult the manufacturer of your device to determine if it is
adequately shielded from RF energy. Your physician may be
able to assist you in obtaining this information.
WARNING: The QUATTRO is capable of amplifying sounds to
a loud volume. It is important to instruct all potential users of
its proper operation. It is advised to adjust the volume control
to the minimum level (Low) when not in use and alert other
users that hearing damage can potentially result from misuse.
WARNING: Use only the power supply indicated in the
User’s Manual.
WARNING: To avoid the possibility of electrical shock, do not
use this product near water (For example, near a bathtub,
wash basin, kitchen sink or laundry tub, in a wet basement or
near a swimming pool) while in the bathtub or shower or when
you are wet.
WARNING: Avoid using the unit during electrical storms. There
4 – ENGLISH
may be a remote risk of electric shock from lightning. If the
electrical storm is present in your immediate area, possibility
of electrical shock exists.
WARNING: Occasionally a power surge can occur on electrical
lines without warning. With any electrical device that you plug
into an outlet, it is suggested you use a surge protector.
surge protector will prevent power surges from damaging your
phone. Surge protectors are simple devices available at your
local hardware store.
WARNING: Do not use a phone if you suspect a gas leak in
the area. The phone’s electrical contacts could create a spark,
which could ignite any heavy concentration of leaking gas.
The QUATTRO Amplified Stereo Neckloop has been designed
to give you years of dependable service. To ensure the utmost
in performance, follow these guidelines in caring for your
QUATTRO Neckloop:
1. Keep the unit out of the reach of small children.
2. If the QUATTRO is not in use do not store the QUATTRO with
batteries installed for an extended length of time.
3. Store your QUATTRO in a dry place.
4. Do not expose your QUATTRO to excessive moisture,
humidity or steam.
5. Avoid dropping or knocking the unit.
6. Do not clean with harsh chemicals, cleaning solvents or
abrasive detergents. To clean, wipe with a soft cloth slightly
dampened in a mild soap-and-water solution.
IMPORTANT: YOUR RECEIPT IS PART OF YOUR WARRANTY
AND MUST BE RETAINED AND PRODUCED IN THE EVENT OF A
WARRANTY CLAIM.
5 – ENGLISH
PLEASE SAVE THESE INSTRUCTIONS
█ LOCATION OF CONTROLS
3
5
1
TOP
4
2
BOTTOM
LEFT SIDE
6 – ENGLISH
RIGHT SIDE
TOP SIDE
1. Indicator LED
BOTTOM SIDE
2. Charging Port and Headset Jack
LEFT SIDE
3. Neckloop Volume Control
4. Headset Volume Control/Song Skip Key
RIGHT SIDE
5. Multi-function Button (MFB)
INTRODUCTION & SET UP
Bluetooth is a specification for short-range radio links between
mobile computers, mobile phones, digital cameras and other
portable devices. The radio operates on the globally available
2.45 GHz ISM ‘free band’, allowing users to use “Bluetooth”
equipment worldwide. The Bluetooth devices communicate
within a certain distance and do not need to be in line of sight.
The QUATTRO is Bluetooth V2.0 compliant, which means it is
backward compatible with audio devices V1.2 or earlier and
supports 4 profiles: Hands-Free Profile (HFP), Headset Profile
(HSP), Advanced Audio Distribution Profile (A2DP) and Audio/
Visual Remote Control Profile (AVRCP).
Installation of your ClearSounds® QUATTRO Amplified
Neckloop is easy.
If at any time you have questions about your QUATTRO
after reading this manual, please contact our ClearSounds®
Customer Service Department at 1-800-965-9043.
7 – ENGLISH
█ PARTS CHECKLIST
Check the contents of the box - The QUATTRO should contain:
Neckloop
AC Charger
Car Charger
USB Cable
User Manual
█ CHARGING THE QUATTRO
Before using your QUATTRO for the first time, you need to
charge its self-contained Li-Polymer battery for approximately
2-3 hours, or until the LED Indicator stops flashing blue and
turns off.
Method 1: Using the AC Power Supply
1. Connect the 3.5mm end of the USB cable into the charging
port of the QUATTRO and then connect the other end into
the USB jack of the base charger.
2. Plug the base charger into a standard AC wall outlet. The
QUATTRO is fully charged when the light goes out. After
a full charge, remove the charger from the wall outlet and
detach the USB cable from the unit.
Method 2: Using the Car Charger
1. Connect the 3.5mm end of the USB cable into the
charging port of the QUATTRO and then connect
the other end into the USB jack of the car charger.
8 – ENGLISH
2. Plug the car charger into the car DC outlet of your vehicle.
The QUATTRO is fully charged when the light goes out.
After a full charge, remove the charger from the DC outlet
and detach the USB cable from the unit.
Method 3: Using A Laptop
1. Connect the 3.5mm end of the USB cable into the charging
port of the QUATTRO and then connect the other end into
a USB jack on your PC. The QUATTRO is fully charged when
the light goes out. After a full charge, remove the cable
from the PC and detach the USB cable from the unit.
NOTE: During charging, you cannot use the QUATTRO. The
batteries will have up to 3 hours of talk time and 120 hours
of standby time before needing recharging. Battery life will
depend on actual usage and amplification levels.
Low Battery:
When your QUATTRO is on and the battery power is running
low, it will beep once every 30 seconds and the LED indicator
flashes red every 30 seconds. You will need to recharge the
battery. The QUATTRO will shut off when the power voltage
falls below necessary operating voltage.
After the battery is fully charged, the LED indicator will turn
off. It takes approximately 1 to 1.5 hours to fully charge the
battery. Do not charge for more than 24 hours.
9 – ENGLISH
█ POWER ON AND OFF
To turn the QUATTRO ON:
Press and hold the Multi-Function Button on the side of the
QUATTRO for 3 seconds. A series of 4 tones (low to high) can
be heard from your hearing aid/cochlear processor when it is in
t-coil mode or from the headset if connected. The LED flashes
blue 4 times.
To turn the QUATTRO OFF:
Press and hold the Multi-Function Button on the side of the
QUATTRO for 3 seconds. A series of 4 tones (high to low) can
be heard from your hearing aid/cochlear processor when it is in
t-coil mode or from the headset if connected. The LED flashes
red 4 times before switching off.
█ WEARING THE UNIT
1. Place the loop around your neck and insert the round
connector plug into the Neckloop Quick Disconnect
plug, forming a continuous loop.
IMPORTANT: To have the Neckloop operate properly, you will
need to be sure the Quick Disconnect connection jack has been
securely clicked in place. There will be two distinct clicks.
2. Make sure your QUATTRO is paired to the device you
wish to use.
3. The QUATTRO allows non hearing aid/cochlear implant
wearers or hearing aid/cochlear implant wearers without
t-coils to connect a 3.5mm headset or ear bud (SmartSound
Earbuds with Reverse Sound technology by ClearSounds are
recommended). Connect your 3.5mm headset or ear buds
directly into the charging jack located on the bottom of your
QUATTRO (see Location of Controls diagram).
4. For hearing aid/cochlear implant wearers with t-coils,
switch your device to “T.”
10 – ENGLISH
FUNCTIONS
█ PAIRING TO A CELL PHONE
Before using your QUATTRO for the first time, you must pair it
with your Bluetooth phone. “Pairing” creates a link between
your Bluetooth equipped cell phone and the QUATTRO, and it
allows your cell phone to remember the QUATTRO’s unique
ID by adding it to a list of paired devices in the phone. The
QUATTRO should be paired once with the phone before use.
Once your QUATTRO and phone are paired, your QUATTRO
automatically connects to your phone if the phone supports
that protocol. Some phones may ask if you want to manually
connect to a Bluetooth device. Check your phone’s manual for
more details on how its Bluetooth functions operate.
Please Note: If the pairing information or log is deleted from
your phone, the QUATTRO unit must be paired again with the
phone prior to use.
To Pair:
1. Place the QUATTRO and phone close to each other (within
3 feet). Make sure that your phone is on.
2. With your QUATTRO off, press and hold the Multi Function
Button for approx. 6 seconds. Make sure that you continue
to hold the Multi Function Button until you see the LED
indicator flash red and blue alternately. The QUATTRO
is now in pairing mode and will stay in pairing mode for
approx. 2 minutes.
3. Enter the Bluetooth menu on your phone and perform a
device search (for the details on device search for your
phone, refer to your owner’s manual). When the scan is
complete, the phone displays the devices discovered.
4. Select Cla7 STEREO BT from the list of devices discovered
and confirm.
5. When prompted by the phone, enter the passkey as
‘0000’. Your phone will confirm that pairing has occurred
and the QUATTRO will confirm it paired successfully with
10 rapid flashes.
11 – ENGLISH
6. The phone information is now stored in the QUATTRO
memory.
7. The QUATTRO LED indicator will flash blue every 3 seconds
when paired and is now in standby mode, ready to make or
receive calls.
If the QUATTRO is not successfully paired within 2 minutes, it
will automatically leave pairing mode. If you still want pairing,
you will need to repeat the steps listed above.
IMPORTANT:
1. After the connection, if you want your cell phone to connect
automatically the next time you power on the QUATTRO,
set the QUATTRO as your authorized device or auto connect
device on your cell phone menu.
2. If you want to connect your QUATTRO to another Bluetooth
enabled device, you will need to disconnect the QUATTRO
with the paired device before establishing a connection
with the intended device.
3. Make sure the QUATTRO and phone you are using are no
more than 33 feet apart so they are within operable range.
4. If the link disconnects, (for example, the device is out of
range) the QUATTRO tries to re-establish the link and will
search for the device for a period of time.
5. The QUATTRO will automatically try to connect to the last
connected phone when powered ON for the first 90 seconds.
Disconnect Options:
1. Power off the QUATTRO
2. Switch off the Bluetooth function on the cell phone
3. Separate the QUATTRO from the cell phone at a distance of
65 feet or more.
█ PAIRING TO ADDITIONAL DEVICES
The QUATTRO now includes the Advanced Audio Distribution
Profile (A2DP) and can also connect to Bluetooth enabled
stereo audio devices for streaming media. Your QUATTRO can
12 – ENGLISH
store pairing information for up to eight (8) different devices
with Bluetooth wireless capability. Devices are stored in a
“Paired Device List” in the memory in a time sequence. When
an attempt to pair more than eight devices is made, the oldest
paired device is removed from the memory list. Any of the
eight paired devices can initiate a connection to the QUATTRO.
The QUATTRO will automatically initiate a connection (once
turned on) with the last device to which it was connected.
If you want to connect the QUATTRO to another device in
the paired device list, you must initiate the connection
from that device. When any of the eight devices initiates a
connection to your QUATTRO, that device then becomes the
“last connected” device.
█ ADJUSTING VOLUME
The receiving volume can be adjusted during a call or when
listening to other audio sources. The volume setting on the
cell phone or other device will add or remove amplification
from the overall system. If amplification is low, check the
volume level on both units. If there is distortion or other
interference, lower the volume on one or both of the units.
Too much amplification can cause distortion.
Adjustment while using the neckloop with t-coils
Use the volume control wheel located on the left side
of the unit (on your right when it is being worn). Slide
the wheel up to increase the volume and slide it down to
decrease the volume.
Adjustment while using a headset
Use the volume control buttons located on the left side
of the unit (on your right when it is being worn), which
is below the volume control wheel used for the neckloop.
Press the + button once to increase the volume and press
the – button once to decrease the volume. To continue
increasing or decreasing volume, pressthe + or – button
13 – ENGLISH
repeatedly, but do not press and hold for longer than 1
second as this will activate the Track Selection function
(see page 18).
█ MAKING AND RECEIVING CALLS
The QUATTRO supports Hands-Free, Headset, Advanced Audio
Distribution (A2DP) and Audio/Visual Remote Control (AVRCP)
Profiles. Accessing call functions depends on which profile
your phone supports. You can activate all functions for HandsFree Profile using the following table. NOTE: Some phones do
not support all features listed. Please consult your phone’s
user guide.
Important Terms to know for pressing the Multi-Function button (MFB):
Press and Release - refers to a duration of less than
0.8 seconds. You should hear 1 beep to confirm the
requested action.
Press and Hold - refers to a duration of more than 0.8 but
less than 1.6 seconds. While holding the multi-function button
you will hear one beep, release the Multi-Function button to
confirm the requested action.
Press and Extend Hold - refers to a duration of more than
3 seconds. While holding the multi-function button you will
hear one beep, release the Multi-Function button to confirm
the requested action.
QUATTRO
Phone
Function
Condition
QUATTRO
Action:
Start Point Phone in Hands-Free Profile
Power ON
--
OFF
Pairing
--
OFF
Power OFF
--
ON (idle)
14 – ENGLISH
Press and Hold the MFB
until the QUATTRO is
powered ON. A set of 4 tones
plays (low to high) and the
LED flashes blue 4 times.
Press and Extend Hold the
MFB for 6 seconds. The LED
will flash blue 4 times and
then alternately flash red
and blue. The QUATTRO can
then be discovered by
another Bluetooth device for
2 minutes.
Press and Extend Hold the
MFB until the QUATTRO is
Power OFF
--
ON (idle)
Make a Voice
Dial Call
ON
ON (idle)
Redialing Last
Number
ON
ON (idle)
ON (ring)
ON (ring)
Ending A Call
ON (on call)
ON (on call)
Rejecting a Call
ON
ON (ring)
(phone ring)
ON (on call) ON (on call)
Receiving A Call
Put Call on Hold
Resume a Call
On Hold
Answering 2nd
Incoming Call
ON (active
On (active
call on Hold) call on Hold)
ON (on call) ON (on call)
To Switch
Between 2
active calls
Transfer call
from Neckloop
to Phone
ON (on call)
ON
ON (on call)
ON
Transfer Call
from Phone to
Neckloop
ON (on call)
OFF
(previously
paired)
User initiated
Reconnect
ON (idle)
ON (not
connected)
ON (on call)
ON (on call)
Muting the
Microphone
15 – ENGLISH
then be discovered by
another Bluetooth device for
2 minutes.
Press and Extend Hold the
MFB until the QUATTRO is
powered OFF. A set of 4
tones plays (high to low) and
the LED is off.
Press and Release the MFB
twice quickly. Follow the
phone’s prompt and say the
desired name and the phone
will dial the number.
Press and Hold the MFB to
recall the last phone number
dialed (number dialed
automatically).
Press and Release the MFB
to answer the call.
Press and Release the MFB
to end the call.
Press and Hold the MFB to
reject the call.
Press and Hold the MFB to
place the current call on
HOLD.
Press and Hold the MFB to
retrieve the call.
Press and Hold the MFB to
put the 1st call on hold and
answer the 2nd call.
Press and Hold the MFB to
place the 2nd call on hold and
return to the first.
Press and Extend Hold the
MFB to turn the QUATTRO off
(4 tones high to low), and
the call is transferred to the
phone.
Press and Hold the MFB.
Once a connection is
established, the call is
transferred to the QUATTRO.
Press and Release the MFB,
and the QUATTRO will try to
reconnect to the last
connected device.
Press and Hold
simultaneously the VOL +
and VOL – buttons to mute
the microphone. Press and
hold the VOL + and VOL –
buttons again to cancel the
muting.
█ LED INDICATOR
LED Indicator status with NO Charger Attached
LED Status
QUATTRO Action
OFF
Flashes red and blue alternately
10 rapid flashes
Flashes at 3 second intervals ( 0.1 seconds
ON, 2.9 seconds OFF)
Flashes at 8 second intervals (2.0 seconds
ON, 6.0 seconds OFF)
Flashes red every 30 seconds
Power OFF
Pairing Mode
Pairing Successful
Standby (No Audio Connection)
Connected to Audio
Battery Low
LED Indicator status with Charger Attached
LED Status
QUATTRO Action
OFF
Flashes solid blue
Charging Complete
Charging
Note: When the QUATTRO is paired to the phone and there is
no operation for five minutes, the blue flashing LED turns off
to preserve battery life. To confirm the QUATTRO is on, press
and release the Multi-Function Button on the QUATTRO. This
resets the timer, and the flashing resumes.
16 – ENGLISH
█ AUDIO TONES
Audio Tone
QUATTRO Action
Series of 4 tones (low to high)
Series of 4 tones (high to low)
Single High Tone
Ring Tone
Single High Tone
Beep once every 30 seconds
No Audio Indication (deteriorating audio
quality)
Singe Low Tone (depends on phone)
Dual High/Low tone if supported by the
phone
5 Rapid tones repeated every 60 seconds
after the phone goes out of network service
for more than 20 seconds
Power ON
Power OFF
Pairing Successful
Incoming Call
End Call
Battery Low
Out of Range
Initiate Voice Activation
Voice tag not recognized
No Network/Services
(Hands-Free Profile)
█ STEREO AUDIO LISTENING
Your ClearSounds QUATTRO includes the Advanced Audio
Distribution Profile (A2DP), which allows users to connect
to other stereo audio devices that support similar Bluetooth
connections including MP3 players, Smartphones and
televisions (via stereo audio Bluetooth transmitters
or dongles).
Follow the same pairing methods as was done when pairing
with a cell phone and follow the pairing instructions for your
audio device. Your cell phone or audio device may need to
have a connection to the QUATTRO activated when switching
between devices or there may be an automatic connection.
Check with your various Bluetooth devices for their method
of operation.
17 – ENGLISH
Playing Music
Find the desired music on your mobile phone or other Bluetooth
device, then press the Multi-Function Button once to play it.
Track Selection (Song Skip)
If you have Audio/Video Remote Control Profile (AVRCP) on your
audio device, you will be able to control the track selection on
the QUATTRO. If you do not have AVRCP on your audio device,
you can use your audio device to control the track selection.
To select a track:
Press and hold VOL + button for 2 seconds during music playing
to skip to the next song or press and hold VOL - button for 2
seconds to return to the previous one.
Please Note: If you are listening to music on your mobile
phone and there is an incoming call, upon hearing the ring,
press the MFB to answer the call. This will mute the music
and when you end the call, the QUATTRO will resume
playing music.
TROUBLESHOOTING
No Sound
1. Make sure Hearing Aid T-coil is turned on and functional.
2. Battery may be dead and needs to be charged (page 8).
3. Verify that the QUATTRO is turned on (page 10).
4. Verify that the phone or audio device is turned on.
5. Check to verify that the QUATTRO is paired and connected
with the device (page 11).
Weak Sound
1. Weak battery (page 8).
2. Turn up the volume on the QUATTRO (page 13).
3. Turn up the volume on the phone.
4. Check your hearing aid – weak battery.
5. Check your hearing aid – weak or non-functional t-coil.
18 – ENGLISH
TECHNICAL SPECIFICATIONS
Model Name:
QUATTRO Bluetooth Stereo Amplified Neckloop
Bluetooth Compliance: Bluetooth Specifications version 2.0
Supported Profiles:
Headset, **A2DP, AVRCP and Hands-free
Frequency Band:
2.4GHz ISM Spectrum; frequency hopping 79 channels
Modulation:
GFSK (Gaussian Frequency Shift Keying)
RF Power:
Class 2, -6-6dBm
Operating Range:
Up to 10m/30ft (indoor)
Talk Time*:
Up to 3hrs with neckloop, up to 13hrs with earbuds/earphone
Standby Time*:
Up to 120hrs
Connection:
Point-to-Point
Security:
Security mode 3 (pairing, encryption,
authentication)
Power Source:
Rechargeable Li-Polymer 650mAh
Charging:
Universal Adaptor 5V/500mA
Charging Time:
3hrs
Batteries: Rechargeable NICAD Battery – Included
Compatibility:
Mobile phones supporting Bluetooth 1.1 (and above), Headset and/or Hands-
free profiles. Other Stereo Audio Devices supporting Bluetooth 1.1 (and above), Headset and/or Hands-free profiles.
Dimension:
1.25“x2.5”x.75”
* May vary based on users operating environment, makes and models of phones
and other Bluetooth devices.
** A2DP or Advanced Audio Distribution Protocol allows the user to connect the
QUATTRO to other Bluetooth enabled stereo audio devices. Using the correct
Bluetooth transmitters will enable the user to connect the QUATTRO to many types
of audio devices, including the television, for streaming media.
19 – ENGLISH
Purchase accessories for your Clearsounds QUATTRO:
Optional Stereo Headset: CS-RS062 SmartSound Earbuds with
Reverse Sound technology. Recommended for
optimal sound quality.
Optional Bluetooth Hub: Used for connecting your QUATTRO
to amulti-line office telephone system. Call ClearSounds for
more information.
Optional Stereo Audio Transmitter: CS-BTDONGLE is used for
connecting your Quattro to a stereo audio output
or source including Televisions.
To learn more, call ClearSounds at 1-800-965-9043
or visit www.clearsounds.com
LIMITED ONE-YEAR WARRANTY
The QUATTRO is warranted by ClearSounds against manufacturing
defect in material and workmanship under normal use for one
(1) year from the date of purchase. The Charging Components are
warranted by ClearSounds for 90 days. Should you experience a
problem, contact our customer service department or visit our
website at www.clearsounds.com.
Be sure to save your sale receipt as the proof of purchase date should
you need warranty service.
In the event that this product fails to function properly within one year
(90 days for Charging Components) of the original purchase due to
defects in materials or workmanship, return the unit (freight prepaid)
with proof of purchase (sales receipt or packing slip, no exceptions)
to ClearSounds Communications. ClearSounds Communications
will either repair or replace the unit (with a refurbished unit or
unit of equal condition) and return it you (using UPS/USPS ground
shipping) at no cost to you. The warranty replacement or repair will
be warranted for a period of 90 days or the remainder of the original
warranty period (from original purchase date); whichever is longer.
20 – ENGLISH
The warranty does not cover accidents, negligence or breakage
to any parts. This includes shipping damage, failure to follow
instructions, misuse, fire, floods, use of incompatible accessories,
Acts of God or failure in your phone service carrier’s line service. The
product must not be tampered with or taken apart by anyone who
is not an authorized ClearSounds Communications® representative.
Tampering with the phone will void any written or implied warranties.
If a defect covered by this warranty should occur, promptly contact
a Customer Service Representative by phone or log onto www.
clearsounds.com to obtain a Return Merchandise Authorization
number and shipping instructions before shipping the product to us.
Any shipment without a (RMA) Return Merchandise Authorization
number will not be accepted and will be returned to you at your
expense. All authorized returned products must be accompanied
with proof of purchase and a brief explanation of the problem.
For out of warranty repairs and service, please contact our Customer
Service Department for instructions. The repair shall be warranted
for 90 days.
IMPORTANT: YOU RECEIPT IS PART OF YOUR
WARRANTY AND MUST BE RETAINED AND
PRODUCED IN THE EVENT OF A
WARRANTY CLAIM.
Service in United States and Canada, contact:
ClearSounds Communications
Attention: Repair Center
1743 Quincy Avenue, Suite 155
Naperville, IL 60540
USA
800-965-9043
Check our website www.clearsounds.com for additional information
and to download additional manuals and information.
21 – ENGLISH
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising