advertisement
INSTRUCTION MANUAL
540TV Lines Super
High Resolution Color Camera
3-AXIS PLASTIC DOME CAMERA
WARNINGS AND CAUTIONS:
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT TO RAIN OR
MOISTURE. DO NOT INSERT ANY METALLIC OBJECTS THROUGH THE VENTILATION GRILLS OR
OTHER OPENINGS ON THE EQUIPMENT.
CAUTION:
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER(OR BACK).
NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
EXPLANATION OF GRAPHICAL SYMBOLS
The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product.
PRECAUTIONS
Safety ----------------------------------------- Installation -----------------------------------
Should any liquid or solid object fall into the cabinet, unplug the unit and have it checked by the qualified personnel before operating it any further.
Do not install the unit in an extremely hot or humid place or in a place subject to excessive dust, mechanical vibration.
Unplug the unit from the wall oulet if it is not going to be used for several days or more. To disconnect the cord, pull it out by the plug. Never pull the cord itself.
Allow adequate air circulation to prevent internal heat build-up. Do not place the unit on surfaces (rugs, blankets, etc.) or near materials(curtains, draperies) that may block the ventilation holes.
The unit is not designed to be waterproof.
Exposure to rain or water may damage the unit.
Cleaning --------------------------------------
Clean the unit with a slightly damp soft cloth.
Use a mild household detergent. Never use strong solvents such as thinner or benzine as they might damage the finish of the unit.
Height and vertical linearity controls located at the rear panel are for special adjustments by qualified personnel only.
Retain the original carton and packing materials for safe transport of this unit in the future.
i
FCC COMPLIANCE STATEMENT
FCC INFORMATION :
THIS EQUIPMENT HAS BEEN TESTED
AND FOUND TO COMPLY WITH THE LIMITS FOR A CLASS A DIGITAL
DEVICE, PURSUANT TO PART 15 OF THE FCC RULES. THESE
LIMITS ARE DESIGNED TO PROVIDE REASONABLE PROTECTION
AGAINST HARMFUL INTERFERENCE WHEN THE EQUIPMENT IS
OPERATED IN A COMMERCIAL ENVIRONMENT. THIS EQUIPMENT
GENERATES, USES, AND CAN RADIATE RADIO FREQUENCY
ENERGY AND IF NOT INSTALLED AND USED IN ACCORDANCE WITH
THE INSTRUCTION MANUAL, MAY CAUSE HARMFUL INTERFERENCE
TO RADIO COMMUNICATIONS. OPERATION OF THIS EQUIPMENT IN
A RESIDENTIAL AREA IS LIKELY TO CAUSE HARMFUL
INTERFERENCE IN WHICH CASE THE USER WILL BE REQUIRED TO
CORRECT THE INTERFERENCE AT HIS OWN EXPENSE.
CAUTION :
CHANGES OR MODIFICATIONS NOT EXPRESSLY
APPROVED BY THE PARTY RESPONSIBLE FOR COMPLIANCE
COULD VOID THE USER'S AUTHORITY TO OPERATE THE EQUIPMENT.
THIS CLASS A DIGITAL APPARATUS COMPLIES WITH CANADIAN
ICES-003.
NORME NMB-003 DU CANADA.
CE COMPLIANCE STATEMENT
WARNING
This is a Class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures.
ii
IMPORTANT SAFEGUARDS
5. ACCESSORIES iii
17. CAUTION-these servicing instructions are
for use by qualified service personnel only.
to reduce the risk of electric shock do not
perform any servicing other than that contained
in the operating instructions unless you are
qualified to do so.
1 1 Class 2 power source only.
17 2 Do NOT use power source other than that specified.
TABLE OF CONTENTS
INTRODUCTION
CAMERA CONNECTION
BASIC CAMERA INSTALLATION
INSTALLING & ADJUSTING CAMERA MODULE
BASE INSTALLATION
FUNCTION SWITCH
LENS ADJUSTMENT
DC AUTO IRIS LENS
DC AUTO IRIS ADJUSTMENT
TROUBLESHOOTING AND MAINTENANCE
SPECIFICATIONS
EXTERNAL DIMENSION
9
10
11
8
8
8
4
5
7
1
2
3 iv
INTRODUCTION
The camera provides high-quality images using SONY CCD technology especially designed for closed-circuit television (CCTV) and security surveillance applications.
Features:
High resolution and high performance 1/3" SONY Super HAD CCD
Technology
Excellent picture quality
540 lines(Color) of resolution
0.25 lux(Color) @ F 1.2 Sensitivity
Auto electronic shutter [1/60(1/50) ~ 1/100,000] and manual electronic
shutter modes
Auto trace white balance modes
BLC (Back Light Compensation)
Day&Night (Auto / Color Fix)
AGC (Auto Gain Control)
Video out (BNC)
4-9mm D&N Auto Iris lens , 2.6-6mm D&N Auto Iris lens
Operates in 12VDC
Use Certified / Listed Class 2 power supply only.
Camera Mount : camera mount directily to the wall or ceiling
1
CAMERA CONNECTIONS
1 2 3
1. Lens : Allows a wide area monitoring.
2. Power : 12V DC input
power source from a DC 12V +/-10%
Use Certified/Listed Class 2 power supply transformer only.
*If use DC 12V power adaptor, use the power consumption 3W over.
3. Video : BNC connector used to connect the camera to a monitor, switcher, etc.
REMINDER:
Never aim the camera directly into the sun.
2
BASIC CAMERA INSTALLATION
Unpack and identify the following parts from the product carton:
D. Anchor
Note : Make sure the power is turned off when connecting the power
adaptor cable.
TOP
Note : Arrow mark indicates the top of the camera image.
3
INSTALLING & ADJUSTING CAMERA MODULE
Use the following drawings to install the camera module to the housing.
8 o
3-Axis Camera Construction
Camera lens can be moved horizontally or vertically and freely swiveled any angle.
Screw Taptite(FC)
M3x6
360 o
360 o
4
BASE INSTALLATION
1
Make mounting holes and cable hole in the place (ceiling) to which this dome camera is installed using the Drilling guide label.
Liner
Dome window
2
To remove dome cover, turn the dome cover counterclockwise until locators reach end of travel and pull off.
Push the liner in the direction of the arrow(three 'OPEN' marks) and pull it out.
5
BASE INSTALLATION, continued
Drilling Guide Label
Plastic anchor
Special Screw (M4)
3
Fasten Mounting screws(2X) and align the dome camera with it like above picture.
Turn the dome camera to left direction about 16 degree.
4
The assembly of the dome window cover and liner is in reverse order of disassembly
Finally, lock dome window cover with locking screw(M2X4) from the accessory kit.
6
FUNCTION SWITCH
CN3 CN4
ON
1 2 3 4 5 6
EI FF BLC AGC D/N N.C.
1. E/I (on/off)
When set to the ON position, the electronic iris switch automatically varies the
camera's shutter to mimic auto-iris control, allowing fixed or manual iris lenses to
be used in a wider range. When this switch is set to ON, turn the F/F switch OFF.
2. FF (on/off)
This function is used for removing flicker, when camera signal format does not
coincide with power source frequency being used.
3. BLC (on/off)
This on/off switch controls backlight compensation. When set to ON, the camera
will automatically try to maintain proper exposure in the specific area even if the
lighting level changes.
4. AGC (off/on)
The auto gain control switch allows the video signals to maintain a constant level.
This switch is useful when using the camera at low-light levels and when lighting
levels change over time. For best low light conditions, this switch should set to ON.
5. D/N (Auto/Color)
Use this switch to set the camera Day/Night mode Auto(ON) or Color(OFF)
Auto : D/N mode converse automatically (AGC must set to ON)
Color : Only Color
6. N.C (no function)
7
LENS ADJUSTMENT (OPTIONAL VARIFOCAL LENS)
Field of view: Adjust setting from Tele (T) to Wide (W) field of View.
Focus: Adjust lens focus from near
(N) to infinity ( ).
Adjust Focus
Adjust Angular Field View
DC AUTO IRIS LENS
4-9mm 2.6-6mm
Image Size 1/3" CCD 1/3" CCD
Focal Length 4.0-9.0mm 5% 2.6-6.0mm 5%
Aperture Ratio 1 : 1.6 5% 1 : 1.6 5%
Angular
Field of View
DIAGONAL
4mm : 92.4
9mm : 39.2
o o
DIAGONAL
2.6mm : 134.6
6mm : 59.2
o o
DC AUTO IRIS ADJUSTMENT
8
IRIS LEVEL
TROUBLESHOOTING
If you experience difficulties operating your camera, refer to the following. If the guidelines do not enable you to solve the problem, contact an authorized technician.
PROBLEM
Nothing appears on the screen.
The image on the screen is dim.
The contrast on the screen is too weak.
The image on the screen flickers.
CHECK
Is the cable connected between the camera and monitor?
Is there power to the monitor?
Is the lens dirty? If so, clean the lens with a soft, clean cloth.
Adjust the contrast feature of the monitor.
Is the camera exposed to strong light?
If so, change the camera position.
Does the camera face directly into the sun or fluorescent lighting?
If so, reposition camera.
PREVENTIVE MAINTENANCE
Following the preventive maintenance schedule allows detection and correction of minor faults before they become serious and cause equipment failure.
Every three months, perform the following:
1. Inspect all connecting cables for deterioration or other damage.
2. Clean components with a clean damp cloth.
3. Verify that all the mounting hardware is secure.
9
SPECIFICATIONS
Power
General
Connector
& etc.
MODEL
Power source
Power consumption
Image sensor
Total pixels
Scanning system
Scanning frequency
Sync. system
Electronic shutter
Resolution
Min. illumination
Video output
O
N
I
T
N
C
F
U
O
N
I
T
N
C
F
U
S/N ratio
Camera Control
E/I
Flickerless
BLC
AGC
Day/Night
White Balance
Power input
Video output
Lens mount
Lens
Operating temperature
Operating humidity
External dimension
Weight
NTSC PAL
DC 12V
2.0 Watts
15.734KHz(H), 59.94Hz(V)
1/60 ~ 1/100,000 sec.
2:1 interlace
795(H) x 596(V)
Internal
15.625KHz(H), 50Hz(V)
1/50 ~ 1/100,000 sec.
540 TV lines
Color ( 0.25 Lux) @ F1.2, 50 IRE
1.0 Vp-p (75 ohm, composite)
More than 50dB (AGC OFF)
Dip Switch
ON/OFF
ON/OFF
ON/OFF
ON/OFF
Auto / Color Fix
ATW Fixed
DC Jack
BNC connector
Fixed mount
4-9mm , 2.6-6mm Vari-focal DC auto iris ICR
-10 C ~ +40 C
0 ~ 96% (non-condencing)
120.0 x 87.9 mm (Bubble Diameter 100)
270g
10
EXTERNAL DIMENSION
Dimensions
87.9
32.9
Maximum Camera and
Lens Size
Window Size
Cable Entry
Weight - Unit:
Shipping:
Unit: mm
2.6L x 1.65W x 1.65H in.
(6.5L x 4.2W x 4.2H cm)
0.1 in. (2.5mm thick), impact-resistant P.C (LEXAN)
3.93 in. (10.0cm) diameter
Two 0.3"(0.8cm)and one 0.5"(1.3cm) opening holes.
0.61 lb. (0.28 kg)
0.82 lb. (0.37 kg)
540TV Lines
Super High Resolution Color Camera
50302443A
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project