Samsung AR09HSSDAWK NEU, XEU, AR12HSSDAWK NEU, XEU, AR09HSSDBWK NEU, XEU, AR12HSSDBWK NEU, XEU air conditioner Service Manual

AR09HSSDAWKNEU AR09HSSDAWKXEU
AR12HSSDAWKNEU AR12HSSDAWKXEU
Basic Code
AR09HSSDBWKNEU AR09HSSDBWKXEU
AR12HSSDBWKNEU AR12HSSDBWKXEU
1 .P recau tio n s
2. Product Specifications
3. Alignment and Adjustments
AR09HSSDAWKNEU
AR12HSSDAWKNEU
4. Disassembly and Reassembly
5. Electrical Parts List
6. Wiring Diagram
7. PCB Diagram
8. Operating Instructions
9. Troubleshooting
AR09HSSDAWKXEU
AR12HSSDAWKXEU
10. Block Diagram
11. Reference Sheet
Contents
1. Precautions ············································································································· 1-1
1-1 Installing the air conditioner ··························································································································
1-2 Power supply and circuit breaker·················································································································
1-3 During operation ················································································································································
1-4 Disposing of the unit ·········································································································································
1-5 Others ······································································································································································
1-1
1-1
1-1
1-2
1-2
2. Product Specifications ······························································································· 2-1
2-1 The Feature of Product ·····································································································································
2-2 Product Specifications ······································································································································
2-3 The Comparative Specifications of Product·····························································································
2-4 Accessory and Option Specifications ·········································································································
2-1
2-2
2-3
2-4
3. Alignment and Adjustments ········································································ 3-1
3-1 Test Mode ·······························································································································································
3-2 Outdoor LED Display Error and Check Method ·····················································································
3-3 Setting Option Setup Method·······················································································································
3-4 Setting Option Setup Method·······················································································································
3-1
3-2
3-5
3-9
4. Disassembly and Reassembly ······································································ 4-1
4-1. Indoor Unit···························································································································································· 4-2
4-2. Outdoor Unit························································································································································ 4-12
5. ASSY COONTROL ························································································ 5-1
5-1 ASSY Control In ·········································································································· ····································
5-2 Assy Control Out ················································································································································
5-1
5-2
6. Electrical Parts List ························································································ 6-1
6-1 INDOOR MAIN PCB (DB92-02873E) ············································· ····························································
6-2 INDOOR SUB PBA(DB92-02874A)·················································································································
6-3 OUTDOOR MAIN PBA(DB92-02866A)-09K·································································································
6-1
6-5
6-7
7. Wiring Diagram ······························································································ 7-1
7-1 Indoor Unit·····························································································································································
7-2 Outdoor Unit ························································································································································
Samsung Electronics
7-1
7-2
1
Contents
8. PCB Diagram ·································································································· 8-1
8-1 Indoor Unit·····························································································································································
8-2 Outdoor PCB ························································································································································
8-3 Wire connecting the indoor unit terminal blocks ·················································································
8-1
8-2
8-3
9. Operating Instructions·················································································· 9-1
9-1 Name of Each Part ··············································································································································
9-2 Wireless Remote Control-Buttons and Display·······················································································
9-1
9-2
10. Troubleshooting ·························································································· 10-1
10-1 Items to be checked first ······························································································································· 10-1
10-2 Communication Error ····································································································································· 10-2
10-3 PCB Inspection Method ································································································································· 10-37
11. Block Diagram ····························································································· 11-1
11-1 Indoor unit ·························································································································································· 11-1
11-2 Outdoor unit······················································································································································· 11-2
12. Reference Sheet ··························································································· 12-1
12-1 Low Refrigerant Pressure Distribution·····································································································
12-2 Pressure & Capacity mark······························································································································
12-3 Q & A for Non-trouble·····································································································································
12-4 Cleaning /Filter Change ·································································································································
12-5 Installation ···························································································································································
12-6 Installation Diagram of Indoor Unit and Outdoor Unit ····································································
2
12-1
12-1
12-2
12-5
12-6
12-7
Samsung Electronics
1. Precautions
1-1 Installing the air conditioner
O Uses should not install the air conditioner by themselves.
Ask the dealer or authorized company to install the air conditioner except window-type air conditioner in U.S.A and Canada.
O If you don't install the air conditioner properly, it may cause a fire, a water leakage or an electric shock.
O You must install the air conditioner according to the national wiring regulations and safety regulations.
O Install the indoor unit higher than 2.5m from the floor to avoid the injury caused by the operation of the fan.
(except the window-type air conditioner)
O The manufacturer is not responsible for any accidents or injury caused by an incorrect installation.
O When installing the built-in type air conditioner, keep all electric cables such as the power cable and the connection cord in
pipes, ducts, or cable channels to protect them from the danger of impact or any other incidents.
1-2 Power supply and circuit breaker
O If the power cord of the air conditioner is damaged, it must be replaced by the manufacturer or a qualified person in order
to avoid a hazard.
O The air conditioner must be plugged into an independent circuit if applicable or connect the power cable to the auxiliary circuit
breaker.
An all pole disconnection form the power supply must be incorporated in the fixed wiring with a contact opening of>3mm.
O Do not extend an electric cord to the air conditioner.
O The air conditioner must be plugged in after you complete the installation.
1-3 During operation
O Do not repair the air conditioner at your discretion.
It is recommended to contact a service center directly.
O Never spill any kind of liquid on the air conditioner.
If this happens, turn off the air conditioner and contact an authorized service center.
O Do not insert anything between the airflow blades to prevent damage of the inner fan and consequent injury.
Keep children away from the air conditioner.
O Do not place any obstacles in front of the air conditioner.
O Do not spray any kind of liquid into the indoor unit. If this happens, turn off the air conditioner and contact a service center.
O Make sure that the air conditioner is well ventilated at all times.
Do not place a cloth or other materials over it.
O Remove the batteries if you don't use the remote control for a long time. (If applicable)
O Use the remote control within 7 meters from the indoor unit. (If applicable)
Samsung Electronics
1-1
1-4 Disposing of the unit
O Before the throwing out the air conditioner, remove the batteries from the remote control.
O When you dispose of the air conditioner, consult your dealer. If pipes are removed incorrectly, refrigerant may blow out
and cause air pollution. When it contacts with your skin, it can cause skin injury.
O The package of the air conditioner should be recycled or disposed of properly for environmental reasons.
1-5 Others
O
O
O
O
1-2
Never store or load the air conditioner upside down or sideways to prevent the damage to the compressor.
Young children or infirm persons should be always supervised when they use the air conditioner.
Max current is measured according to IEC standard for safety.
Current is measured according to ISO standard for energy efficiency.
Samsung Electronics
2. Product Specifications
2-1 The Feature of Product
䒲 #2 step cooling
- Get cool quickly and keep cool comfortably without shivering
䒲 #Single user mode
- No worrying about the electricity bill, even using it when you're alone.
䒲 #Crystal gloss design
- Uniquely stylish and innovative design to enhance your life and home
䒲 #Smart Wi-Fi
- Control air conditioner anytime and anywhere
䒲 #Smart Installation
- Get the confidence that it's perfectly installed
䒲 #Smart Installation
- Get the confidence that it's perfectly installed
䒲 #Smart Check
- Don’t worry about the trouble-shooting in your home
䒲 #Triple Protector Plus
- Use longer without damage in unsuitable conditions
䒲 E# asy Installation
- Secure the easy Installation of Indoor unit and pipe connection
䒲 #Easy Filter
- Quick and easy to clean filter saves time and effort
Samsung Electronics
2-1
2-2 Product Specifications
AR09HSSDAWKNEU
MODEL
ITEM
Indoor Unit
Type
Capacity
Running Frequency
(Low/Std/Max)
0.85/3.2/6
0.857/4.0/6.6
Cooling
Hz
15/35/49
15/53/61
(Low/Std/Max)
15/48/94
15/61/103
dB
(H/L)
-
4210
ph-V-Hz
1phase, 220~240V, 50Hz
1phase, 220~240V, 50Hz
KW
(Low/Std/Max)
0.21/0.52/0.78
0.21/0.85/0.99
0.18/0.67/1.75
0.18/0.95/2
A
(Low/Std/Max)
1.4/2.6/3.7
1.4/4/5
1.2/3.3/7.8
1.2/4.4/8.6
70/90/95
70/90/95
Heating
%
(Low/Std/Max)
70/90/95
70/90/95
W*H*D
mm
896*275*260
790*545*285
896*275*260
790*545*285
kg
10.4
35.5
10.4
35.5
Heating
Cooling
Weight(Net)
Liquid
mm
6.35 (1/4 inch)
6.35 (1/4 inch)
Gas
mm
9.52 (3/8 inch)
9.52 (3/8 inch)
L*D
550±20
550±20
ROTARY,UG9T115FUAEQSS
ROTARY,UG9T115FUAEQSS
Type
HERMETIC
HERMETIC
Rated Output(W)
-
-
Drain Hose
Type
Compressor
-
4780
Cooling
Size
-
53
W/W
(Std)
Heating
Refrigerant Pipe
45/43
4120
Cooling
Outer Dimension
51
4810
Cooling
Power Factor
43/41
-
Heating
Operating Current
Wall-mounted
Heating
Power
Pow
Wall-mounted
0.99/3.5/4.0
Sound power
Power Consumtion
Outoor Unit
0.99/2.5/3.3
pressure
Energy Efficiency
Ratio
Indoor Unit
KW
Sound
Noise
Outoor Unit
Cooling
Heating
Performance
AR12HSSDAWKNEU
Motor
Oil Type
Blower
Type
motor
Type
PROPELLER
CROSS-FLOW
PROPELLER
BLDC
BLDC
BLDC
BLDC
2ROWx14STEPx705, 12ROWx14STEPx705, 12ROWx24STEPx(850+825),
2ROWx24STEPx(850+82
2Path
2Path
4-2-2Path
5), 4-2-2Path
1ROWx10STEPx705
1ROWx10STEPx705
Heat Exchanger
Refrigerant Control Unit
CAPILARRY
CAPILARRY
Freezer Oil Capacity
cc
-
-
Refrigerant to Change(R410A)
g
1100
1100
NONE
NONE
Cooling
-10~46
-10~46
Heating
-15~24
-15~24
Proterction Device(OLP)
Operation condition range
2-2
CROSS-FLOW
Samsung Electronics
3
Outdoor Unit
Indoor Unit
Net Weight
Indoor Unit
Outdoor Unit
Indoor Unit
Outer Dimension
Outdoor Unit
Indoor Unit
Noise
Outdoor Unit
Air Purifying System
Filter
Design
MODEL
10.4
35.5
896*275*260
790*545*285
43/41
51
FULL HDFILTER
10.4
35.5
896*275*261
790*545*285
45/43
53
FULL HDFILTER
Develop Model
AR09HSSDAWKNEU
AR12HSSDAWKNEU
3
2-4
3. Alignment and Adjustments
3-1 Test Mode
Q How to Approach Test Mode
You can approach the test mode by pressing the on/off switch of
indoor unit for 5 seconds.
Q Test mode operation option
After installing the air conditioner, check whether each subordinate is normally operated or not by operating the test mode.
When an Error occurs, display the Error Mode.
● Operation Mode : Cool mode. operate the cool mode by operating the compressor by force without the compressor ON/OFF
according to the set temperature/indoor temperature. (Do not follow the antifreeze control)
● Up-down louver : Up-down swing mode
● Indoor Fan : Turbo
●
●
Note
Because the teat mode operate the cool mode by force not related to the set temperature / indoor
temperature, check whether each subordinate is operated normally or not after completing installation
and must turn off the power of the air conditioner.
Samsung Electronics
3-1
3-2 Display Error and Check Method
3-2-1 Indoor Display Error and Check Method
ER R O R M O D E
E101 / E102
3-2
D ES C R IP T IO N
Communication Error (Indoor Outdoor)
E121
ROOM TH sensor error
E122
INDOOR MID, INDOOR IN PIPE-TH sensor error
E154
Fan Error (Indoor)
E162
EEPROM Error (Indoor)
E163
Option Error
E203
Time out Comm. (Inv Micom Main Micom)
E221
OUT-TH(Outdoor Temperature) Sensor Error
E231
CON-TH(Cond Temperature) Sensor Error
E251
DIS-TH(Discharge Temperature) Sensor Error
E416
DIS-TH(Discharge Temperature) Over Error
E422
EEV or Valve Close error-Self diagnosis
E440
Prohibit Operation Condition Error (Heating)
E441
Prohibit Operation Condition Error (Cooling)
E458
Fan Error(Outdoor)
E461
Comp Starting Error
E462
AC Input I_Limit Trip Error
E464
IPM Over Current(O.C) Error
E465
Comp V_limit/I_limit Error
E466
DC-Link Voltage Under/Over Error
E467
Comp Wire Missing Error
E468
Current Sensor Error
E469
DC-Link Voltage Sensor Error
E470
EEPROM Data Error (no data)
E471
EEPROM Data Error (Main Micom Inv Micom)
E474
Heatsink Sensor Error
E483
Over Voltage Protection Error
E484
PFC Over Load Error
E485
Input Current Sensor Error
E488
AC Input Voltage Sensor Error
E500
Heatsink Over Temperature Error
E554
Gas Leak Error
Samsung Electronics
Outdoor LED Display Error and Check Method
Samsung Electronics
3-3
3-3 Setting Option Setup Method
ex) Option No. :
Note :
SEG1, SEG7, SEG13, SEG19 need not to be pressed in, so in fact the Option No. we should press in is as below.
SEG1 SEG2 SEG3 SEG4 SEG5 SEG6 SEG7 SEG8 SEG9 SEG10 SEG11 SEG12 SEG13 SEG14 SEG15 SEG16 SEG17 SEG18 SEG19 SEG20 SEG21 SEG22 SEG23 SEG24
SEG25 SEG26 SEG27 SEG28 SEG29 SEG30 SEG31 SEG32 SEG33 SEG34 SEG35 SEG36 SEG37 SEG38 SEG39 SEG40 SEG41 SEG42 SEG43 SEG44 SEG45 SEG46 SEG47 SEG48
Step 1
Enter the Option Setup mode.
1. Tack out the batteries of remote control.
2. Press the temperature
button simultaneously and insert the battery again.
3. Make sure the remote control display shown as
.
Step 2
Enter the Options Setup mode and select your options asscording to the following procedure.
Samsung Electronics
3-5
Step 3
Upon completion of the selection, check you made right selections.
Press the Mode
Selection key to set the display part and check the display part.
→ The display part shows like below when each time you press Mode button.
Step 4
Pressing the ON/OFF button (
).
When pressing the operation ON/OFF key with the direction of remote control for unit, the sound ’ Ding’’ or ’ Diriring’’ is heard
and the OPERATION ICON(
) lamp of the display is flickering at the same time, then the input of option is completed.
(If the deriving sound isn’t heard, try again pressing the ON/OFF button.)
3-6
Samsung Electronics
Step 5
Enter the Options Setup mode and select your options asscording to the following procedure.
Step 1 (Enter the Option Setup mode) is executed.
(Seg25 ~ 48 for setting remote control Setup)
Push the
Mode button to set the display panerl to 2.
Every time you push the
’
’...
Push the
’
’
Samsung Electronics
’...
’
’
’
’
’
’
’
repeatedly.
Mode button to set the display panerl to 1.
Every time you push the
’
button, the display panel reads
’
’
’
button, the display panel reads
’
’
’
’
repeatedly.
3-7
Model
AR09HSSDAWKNEU
AR12HSSDAWKNEU
1~6
011045
011045
7~12
156248
156269
13~18
271920
272328
19~24
372716
372816
25~30
020000
020000
31~36
100000
100000
37~42
200001
200001
43~48
300000
300000
((3520'RZQORDGFRPPXQLFDWLRQPRGHO
Ƶ0HWKRG8VLQJ&RPPXQLFDWLRQOLQH
3RZHURII
7DNHRIIWKHVLGHFRYHU
&RQQHFW3&'RZQORDG-LJ3%$
))
SLQ
))
SLQ
56WR
&RQYHUWHU
([HFXWHWKH,QYHUWHU'RZQORDGSURJUDP
6HOHFW&203RUWDQGFRQQHFW
&/,&.
2SHQWKHILOHVUF
&OLFNWKH6WDUWEXWWRQDQGUHVHWWKHSRZHU
5HVHW
SRZHU
:DLWLQJGRZQORDG
'RZQORDG
&/,&.
&/,&.
6DPVXQJ(OHFWURQLFV
&/,&.
Ƶ0HWKRG8VLQJ6HULDOOLQH
3RZHURII
7DNHRIIWKH&DELQHW&KHFNWKH/('RII
&RQQHFW3&'RZQORDG-LJ3%$
Download connector
(10pin)
56WR6HULDO
'RZQORDG&RQYHUWHU
'RZQORDGFRQQHFWRU
SLQ%ODFN
'%$&1
'%$&1
'%$&1
'%%&1
3,15;'7;'*1'9&&
'RZQORDGFRQQHFWRU
SLQ%ODFN
'%$&1
'%$&1
3,15;'7;'*1'9&&
([HFXWHWKH,QYHUWHU'RZQORDGSURJUDP
6HOHFW&203RUWDQGFRQQHFW
&/,&.
2SHQWKHILOHVUF
&OLFNWKH6WDUWEXWWRQ
:DLWLQJGRZQORDG
'RZQORDG
&/,&.
&/,&.
&/,&.
6DPVXQJ(OHFWURQLFV
4. Disassembly and Reassembly
Q Necessary Tools
Item
Remark
+SCREW DRIVER
MONKEY SPANNER
- SCREW DRIVER
Samsung Electronics
4-1
4-1. Indoor Unit
No
Parts
Procedure
1
PANEL-FRONT
1) Stop the driving of air conditioner and shut off
main power supply.
Remark
2) Detach FILTER PRE from the PANEL FRONT.
3) Cover Panel is assembled on bottom of indoor
unit as shown in the figure.
Remove the Cap Screw as shown on the right
side and then remove the screw and separate
the Cover Panel.
4-2
Samsung Electronics
No
Parts
Procedure
Remark
4) Cover Panel is fixed to body by Hook in center
area and side area.
Center area
Side area
Side area
HOOK
9/12K
18/24/30K
5) Separate the hook after pushing both end of
Cover Panel as shown in the figure.
(Watch out for the damage of the hook)
6) Raise front part upward obliquely as shown in
the figure and then remove the hooks.
Samsung Electronics
4-3
No
Parts
Procedure
Remark
Caution:
Assembly of Cover Panel after service end.
- Reassembly is in the reverse order of the
removal.
- Piping and drain hose must be careful not to
damage and Progress must be done with both
hands.
Hook (Side)
Hook (Center)
Screw
Cap Screw
4-4
Samsung Electronics
No
Parts
Procedure
Remark
7) To detach the PANEL-FRONT from the main
frame, unfasten 2 screws at the bottom.
(use + Screw Driver)
8) To detach the COVER-PANEL from the main
frame, loosen 4 HOOK Structures.
When separate the hook :
Use the (-) screw Driver.
(-)Screw Driver Insert the hook and then pull the
hook as shown on the right side.
(Watch out for the damage of the hook)
Samsung Electronics
4-5
No
Parts
Procedure
Remark
9) Remove the Panel Frame from the Main
Frame as shown on the right side.
10) Remove the WIFI KIT connector.
WIFI KIT connector is located of Panel Front.
(For model with WIFI KIT)
4-6
Samsung Electronics
No
Parts
5
EVAPORATOR
Procedure
Remark
9) Take off the CASE-CONTROL from
the main frame after loosen the remaining
connector.
Caution:
When you separate the connector,
pull pressing the locking button.
3
4-8
TRAY DRAIN
1) To detach TRAY-DRAIN from the main frame,
pull the bottom of the TRAY-DRAIN towards
you.
Samsung Electronics
No
Parts
4
Evaporator
Procedure
Remark
1) Detach the HOLDER PIPE.
2) Unfasten the screw at the left side.
(use + Screw Driver)
3) Unfasten the screw at the right side.
(use + Screw Driver)
4) To detach Evaporator from the main frame,
pull the bottom of the Evaporator towards
you.
Samsung Electronics
4-9
No
Parts
5
FAN MOTOR
&
CROSS FAN
Procedure
Remark
1) Unfasten the screw. (use + Screw Driver)
2) Detach the FAN Motor case.
3) Unfasten the screw a little.
(use + Screw Driver)
4) Pull the CROSS-FAN to the left side.
4-10
Samsung Electronics
No
Parts
6
Assy SPI Lamp
Procedure
Remark
1) Remove the Assy SPI Lamp from the Back
Body as shown on the right side.
Caution:
- Confirm Seal of backside necessarily after
replace of Assy SPI Lamp.
- Seal should be close adhesion to SPI Lamp.
- Measure as shown on the right side since
replace.
(If the seal is not close adhesion perfectly :
Defectiveness can happen)
Samsung Electronics
4-11
4-2 Outdoor Unit
3) Detach the Cabinet Upper like the picture.
4-2-1
5) Loosen 2 screw(CCW) on the right side of
Cabinet Front. (Use +Screw Driver)
6) Loosen 2 screw(CCW) on the left side of
Cabinet Front. (Use +Screw Driver)
7) Loosen 3 screw(CCW) on the front side of
Cabinet Front. (Use +Screw Driver)
4-2-2
8
3
9
4-2-4
1) Release Nut at Fan Boss
2) Release 3 screws st Motor Bracket.
3) Detach Motor Wire from the Assy Control Out.
1
4-2-5
5-2
ASSY CONTROL IN (9/12K)
10
5
6
7
9
8
26
27
25
3
4
20
24
1
23
2
11
22
21
12
13
19
14
18
No
CODE
DB93-14235N
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
5-2
17
16
15
Description
ASSY CONTROL IN
Spec
Q'TY
10x10xT0.07,AL SHEET
DB63-03553C
DB61-05826A
Aluminum SHEET
CASE-CONTROL IN
CASE-CONTROL IN
DB93-14203A
POWER WIRE
T/B-main(power)
1
DB93-14245A
DB65-00326A
EARTH WIRE
TERMINAL BLOCK
EARTH WIRE
TERMINAL BLOCK
1
1
DB62-11656F
SEAL CUTT
PVC,BLACK,T1,W54
1
DB62-11680A
SEAL CONTROL
1
DB68-02809A
DB93-14447A
ASSY-LABEL
COMMUNICATION WIRE
FLOCKED,BLACK,T1,W50,54
ASSY-LABEL
T/B-main(485)
DB93-14207A
FUSE WIRE
power-main(12V 5V)
1
DB63-03553D
DB68-33293A
Aluminum SHEET
ASSY-LABEL
22x22xT0.07,AL SHEET
ASSY-LABEL
1
1
DB61-05807A
PLATE-CONTROL IN
F01
1
DB68-33292A
DB91-00309A
DB61-05812A
ASSY-LABEL
SCREW
PLATE
ASSY-LABEL
1
1
1
6009-001001
6002-000231
DB61-05871A
SCREW
SCREW
HOLDER-WIRE CLAMP
TH,M4,L10,ZPC(WHT),SWRCH18Aϔ
M4,L12,ZPC(WHT),SWRCH18Aϔ
HOLDER-WIRE CLAMP
3
2
1
DB92-02873A
DB92-02861A
MAIN PBA
POWER PBA
STD4
STD11W
1
1
DB71-50021A
DB93-14208A
DB95-05163A
WIRE-SADDLE
ASSY CONNECTOR WIRE-DC
ASSY THERMISTOR IN
WIRE-SADDLE
power-main(310V 19V)
sensor 1roomˈ2evap
1
1
1
DB93-14205A
DB93-14202A
DB93-14221A
ASSY CONNECTOR WIRE-DC
ASSY CONNECTOR WIRE-DC
ASSY CONNECTOR WIRE-DC
M3,L25,ZPC(WHT),SWRCH18Aϔ
PLATE
Step-main(Left)
main-power(SMPS IN)
FJM
4
1
1
1
1
1
1
Samsung Electronics
5-3
Assy Control Out
AR09HSSDBWKXEU
AR12HSSDBWKXEU
NAME
No
5-4
CODE
Q'ty
unit
1
GREASE-SILICON
0205-000178
0.002 KG
2
SCREW-TAPPING
6002-000527
1 PC
3
SCREW-TAPPING
6002-000536
1 PC
4
HEAT SINK
DB62-11646A
1 PC
5
SEAL CUTT
DB62-11656B
0 M
6
CABLE TIE
DB65-10088B
2 PC
7
LABEL BAR CODE
DB68-02809A
1 PC
8
ASSY CASE CONTROL OUT
DB90-06308N
1 PC
9
ASSY COVER CONTROL-UP
DB90-07729A
1 PC
10
ASSY CASE CONTROL
DB90-07833A
1 PC
11
ASSY-SCREW MACHINE
DB91-00933A
4 PC
12
ASSY MODULE
DB92-02862A
1 PC
13
ASSY PCB MAIN
DB92-02866A
1 PC
14
ASSY CONNECTOR WIRE
DB93-09493C
1 PC
15
ASSY CONNECTOR WIRE
DB93-09497E
1 PC
16
ASSY CONNECTOR WIRE-POWER
DB93-14275A
1 PC
17
ASSY CONNECTOR WIRE-DC SIGNDB93-14276A
1 PC
18
ASSY CONNECTOR WIRE-DC SIGNDB93-14277A
1 PC
Samsung Electronics
6. Electrical Parts List
6-1
INDOOR MAIN PCB (DB92-02873E)
Parts Code
1405-001239
2301-002032
2301-002032
3002-001139
3711-000177
3711-000203
3711-000296
3711-002001
3711-003404
3711-003845
3711-004122
3711-004236
3711-005096
3711-005097
3711-005504
DB27-00096A
DB67-00942A
DB68-02809A
DB94-04097A
0501-000362
1404-001194
3601-001765
3711-000024
3711-000941
3711-000998
3711-000999
DB94-04098A
0402-001741
0406-001204
0406-001204
0406-001204
0501-000465
0504-001080
0504-001080
0506-000175
0506-000175
0604-001002
0604-001002
0604-001002
0801-000393
1006-001325
1202-000104
1203-006245
1203-007526
2007-000029
2007-000029
2007-000067
2007-000072
Samsung Electronics
Design Loc
Q701
VA71
XC71
XC72
BZ61
CN21
CN75
CN72
CN31
CN71
CN91
CN32
CN43
CN63
CN62
CN51
FT71
VA71-1
LABEL BAR CODE
Q801
PTC2
F701
CN76
CN81
CN77
CN61
D701
CD81
CD82
CD83
Q702
Q601
Q802
IC05
IC06
PC03
PC04
PC05
IC08
IC07
IC11
IC03
IC02
R850
R851
R713
R717
Parts Dsecription
Quantity
TR-POWER
1
VARISTOR
1
C-FILM,LEAD-PPF
1
C-FILM,LEAD-PPF
1
BUZZER-PIEZO
1
HEADER-BOARD TO CABLE
1
HEADER-BOARD TO CABLE
1
HEADER-BOARD TO CABLE
1
HEADER-BOARD TO CABLE
1
HEADER-BOARD TO CABLE
1
HEADER-BOARD TO CABLE
1
HEADER-BOARD TO CABLE
1
HEADER-BOARD TO CABLE
1
HEADER-BOARD TO CABLE
1
HEADER-BOARD TO CABLE
1
HEADER-BOARD TO CABLE
1
COIL CHOKE
1
CAP
1
LABEL BAR CODE
1
ASSY PCB AUTO
1
TR-SMALL SIGNAL
1
THERMISTOR-PTC
1
FUSE-ETC
1
HEADER-BOARD TO CABLE
1
HEADER-BOARD TO CABLE
1
CONNECTOR-HEADER
1
HEADER-BOARD TO CABLE
1
ASSY PCB SMD
1
DIODE-RECTIFIER
1
DIODE-TVS
1
DIODE-TVS
1
DIODE-TVS
1
TR-SMALL SIGNAL
1
TR-DIGITAL
1
TR-DIGITAL
1
TR-ARRAY
1
TR-ARRAY
1
PHOTO-COUPLER
1
PHOTO-COUPLER
1
PHOTO-COUPLER
1
IC-CMOS LOGIC
1
IC-BUS TRANSCEIVER
1
IC-VOLTAGE COMP.
1
IC-VOL. DETECTOR
1
IC-POSI.FIXED REG.
1
R-CHIP
1
R-CHIP
1
R-CHIP
1
R-CHIP
1
6-1
INDOOR MAIN PCB (DB92-02873A)
2007-000076
2007-000076
2007-000076
2007-000078
2007-000078
2007-000078
2007-000078
2007-000084
2007-000087
2007-000090
2007-000090
2007-000090
2007-000090
2007-000090
2007-000090
2007-000090
2007-000090
2007-000090
2007-000116
2007-000130
2007-000138
2007-000138
2007-000138
2007-000138
2007-000138
2007-000138
2007-000138
2007-000138
2007-000138
2007-000138
2007-000140
2007-000140
2007-000140
2007-000140
2007-000143
2007-000143
2007-000143
2007-000148
2007-000148
2007-000148
2007-000148
2007-000148
2007-000148
2007-000148
2007-000148
2007-000148
2007-000148
2007-000148
2007-000148
2007-000148
6-2
R601
R602
R716
R703
R706
R805
R815
R707
R708
R701
R704
R705
R723
R801
R802
R803
R804
R816
R825
R715
R508
R515
R516
R517
R518
R519
R520
R539
R542
R809
R538
R545
R806
R901
R511
R512
R513
R502
R503
R504
R505
R506
R507
R510
R521
R522
R523
R524
R525
R526
cont.
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
Samsung Electronics
INDOOR MAIN PCB (DB92-02873A)
2007-000148
2007-000148
2007-000148
2007-000148
2007-000148
2007-000148
2007-000148
2007-000148
2007-000148
2007-000148
2007-000148
2007-000148
2007-000148
2007-000148
2007-000148
2007-000148
2007-000157
2007-000162
2007-000162
2007-000171
2007-000171
2007-000171
2007-000171
2007-000171
2007-000171
2007-000303
2007-000385
2007-000455
2007-000475
2007-000924
2007-000924
2007-000924
2007-000939
2007-001096
2007-001313
2007-001313
2007-001313
2007-001313
2007-001313
2007-001433
2007-007313
2007-007313
2007-007313
2007-009922
2007-009922
2007-009922
2203-000257
2203-000257
2203-000438
2203-000438
6-4
R527
R528
R529
R530
R531
R532
R533
R534
R543
R544
R807
R808
R810
R824
R903
R904
R902
R820
R821
R831
R833
R835
R837
R839
R843
R702
R115
R712
R709
R112
R113
R114
R711
R714
R404
R405
R406
R410
R811
R618
R401
R402
R403
R301
R302
R303
C705
C801
C508
C516
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
C-CER,CHIP
C-CER,CHIP
C-CER,CHIP
C-CER,CHIP
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
Samsung Electronics
INDOOR MAIN PCB (DB92-02873A) `c̀ont.
2203-000438
2203-000438
2203-000440
2203-000440
2203-001071
2203-005249
2203-005249
2203-005249
2203-005249
2203-005249
2203-005249
2203-005249
2203-005249
2203-005249
2203-005249
2203-005249
2203-005249
2203-005249
2203-005249
2203-005249
2203-005249
2203-005249
2203-005249
2203-005249
2203-005249
2203-005249
2203-005249
2203-005249
2203-006496
2203-006960
2203-007486
2203-007486
2203-007486
2203-007486
2203-007486
2203-007486
2203-007486
2203-007486
2203-007486
2203-007486
2203-007486
2203-007486
2402-000120
2402-001145
2402-001145
2802-001211
DB41-01221A
DB91-01550A
0903-001864
DB98-31449A
6-4
C520
C901
C711
C715
C519
C401
C402
C403
C511
C513
C514
C517
C522
C529
C530
C531
C533
C702
C704
C710
C712
C713
C802
C803
C805
C806
C807
C809
C707
C708
C509
C512
C515
C518
C521
C523
C526
C528
C551
C552
C804
C808
C706
C701
C703
X501
PCB MAIN
IC04
ASSY-LABEL MICOM
C-CER,CHIP
C-CER,CHIP
C-CER,CHIP
C-CER,CHIP
C-CER,CHIP
C-CER,CHIP
C-CER,CHIP
C-CER,CHIP
C-CER,CHIP
C-CER,CHIP
C-CER,CHIP
C-CER,CHIP
C-CER,CHIP
C-CER,CHIP
C-CER,CHIP
C-CER,CHIP
C-CER,CHIP
C-CER,CHIP
C-CER,CHIP
C-CER,CHIP
C-CER,CHIP
C-CER,CHIP
C-CER,CHIP
C-CER,CHIP
C-CER,CHIP
C-CER,CHIP
C-CER,CHIP
C-CER,CHIP
C-CER,CHIP
C-CER,CHIP
C-CER,CHIP
C-CER,CHIP
C-CER,CHIP
C-CER,CHIP
C-CER,CHIP
C-CER,CHIP
C-CER,CHIP
C-CER,CHIP
C-CER,CHIP
C-CER,CHIP
C-CER,CHIP
C-CER,CHIP
C-AL,SMD
C-AL,SMD
C-AL,SMD
RESONATOR-CERAMIC
PCB MAIN
ASSY MICOM
IC-MICROCONTROLLER
ASSY-LABEL MICOM
Samsung Electronics
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
6-2
INDOOR SUB PBA(DB92-02874A)
Parts Code
0609-001377
3711-004067
DB63-03547A
DB94-04100A
0406-001005
2007-000029
2007-000290
2203-000206
2203-000444
DB94-04099A
2401-003107
3404-001220
DB41-01222A
Samsung Electronics
Design Loc
RM01
CN01
COVER-SENSOR
CD01
J1
R01
C03
C02
C01
SW01
PCB SUB
Parts Description
MODULE REMOCON
HEADER-BOARD TO CABLE
COVER-SENSOR
ASSY PCB SMD
DIODE-TVS
R-CHIP
R-CHIP
C-CER,CHIP
C-CER,CHIP
ASSY PCB AUTO
C-AL
SWITCH-TACT
PCB SUB
Quantity
1
1
1
1
1
1
1
1
1
1
1
1
1
6-5
OUTDOOR MAIN PBA(DB92-02866A) -
6-12
(cont.)
modelCode
Design Loc
Parts Description
Quantity
0202-001338
0202-001463
0204-004665
0204-005794
1404-001498
1405-000154
1405-000154
1405-001239
1405-001239
2201-000540
2201-002002
2201-002002
2201-002002
2201-002002
2301-001285
2301-001285
2306-000123
2401-004874
2401-004874
2401-004874
3501-001154
3501-001154
3501-001279
3711-000177
3711-000203
3711-000296
3711-000760
3711-002001
3711-003404
3711-003843
3711-007656
3711-007659
3711-007817
3712-001047
3712-001139
3712-001139
4719-002483
4719-002484
DB27-00097A
DB61-05296A
DB61-05916A
DB68-02809A
DB94-04084A
0504-001044
2201-002427
2401-000303
2401-000303
2401-001838
2401-002438
SOLDER-BAR
SOLDER-WIRE
FLUX
SOLVENT
PTC020
VA002
VA003
VA001
VA401
C425
C004
C005
C012
C013
C001
C006
C412
CE101
CE102
CE103
RY022
RY030
RY021
CN301
CN030
CN901
CN551
CN201
CN150
CN251
CN402
CN401
CN501
CN003
CN001
CN002
PFC050
IPM400
FT001
SUPPORT-IC
SUPPORT-PCB
-
SOLDER-BAR
SOLDER-WIRE
FLUX
SOLVENT
THERMISTOR-PTC
VARISTOR
VARISTOR
VARISTOR
VARISTOR
C-CERAMIC,DISC
C-CERAMIC,DISC
C-CERAMIC,DISC
C-CERAMIC,DISC
C-CERAMIC,DISC
C-FILM,LEAD-PPF
C-FILM,LEAD-PPF
C-FILM,LEAD-PPF
C-AL
C-AL
C-AL
RELAY-MINIATURE
RELAY-MINIATURE
RELAY-POWER
HEADER-BOARD TO CABLE
HEADER-BOARD TO CABLE
HEADER-BOARD TO CABLE
HEADER-BOARD TO CABLE
HEADER-BOARD TO CABLE
HEADER-BOARD TO CABLE
HEADER-BOARD TO CABLE
HEADER-BOARD TO CABLE
HEADER-BOARD TO CABLE
HEADER-BOARD TO BOARD
CONNECTOR-TERMINAL
CONNECTOR-TERMINAL
CONNECTOR-TERMINAL
POWER MODULE
POWER MODULE
COIL CHOKE
SUPPORT-IC
SUPPORT-PCB
LABEL BAR CODE
ASSY PCB AUTO
TR-DIGITAL
C-CERAMIC,DISC
C-AL
C-AL
C-AL
C-AL
0.47
4.27
0.43
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
Q151
C901
CE162
CE163
CE151
CE902
Samsung Electronics
OUTDOOR MAIN PBA(DB92-02866A) - (cont.)
2401-003224
2401-003585
3601-001538
3711-000015
3711-000024
3711-000879
3711-000880
3711-000998
3711-000999
4715-001093
DB94-04085A
0202-001459
0401-001099
0401-001099
0401-001099
0401-001099
0401-001099
0401-001099
0401-001099
0401-001099
0401-001099
0401-001099
0401-001099
0401-001099
0401-001099
0401-001099
0401-001099
0401-001099
0402-001795
0403-001499
0403-001499
0404-001020
0404-001020
0406-001204
0406-001204
0406-001204
0501-000465
0504-001008
0504-001008
0504-001008
0504-001008
0504-001080
0506-000175
0506-000175
0506-000175
0601-002423
0601-002955
0601-002956
0601-002956
0604-001172
6-12
CE152
CE901
F001
CN203
CN202
CN152
CN151
CN701
CN204
DSA001
SOLDER-CREAM
D020
D021
D030
D152
D153
D454
D500
D501
D502
D503
D504
D505
D507
D508
D904
D905
D903
ZD401
ZD420
D491
D492
TD301
TD302
TD303
Q551
Q351
Q352
Q901
Q903
Q902
IC061
IC701
IC702
LED801
LED803
LED551
LED802
PC151
C-AL
C-AL
FUSE-AXIAL LEAD
HEADER-BOARD TO CABLE
HEADER-BOARD TO CABLE
HEADER-BOARD TO CABLE
HEADER-BOARD TO CABLE
CONNECTOR-HEADER
HEADER-BOARD TO CABLE
SURGE ABSORBER
ASSY PCB SMD
SOLDER-CREAM
DIODE-SWITCHING
DIODE-SWITCHING
DIODE-SWITCHING
DIODE-SWITCHING
DIODE-SWITCHING
DIODE-SWITCHING
DIODE-SWITCHING
DIODE-SWITCHING
DIODE-SWITCHING
DIODE-SWITCHING
DIODE-SWITCHING
DIODE-SWITCHING
DIODE-SWITCHING
DIODE-SWITCHING
DIODE-SWITCHING
DIODE-SWITCHING
DIODE-RECTIFIER
DIODE-ZENER
DIODE-ZENER
DIODE-SCHOTTKY
DIODE-SCHOTTKY
DIODE-TVS
DIODE-TVS
DIODE-TVS
TR-SMALL SIGNAL
TR-DIGITAL
TR-DIGITAL
TR-DIGITAL
TR-DIGITAL
TR-DIGITAL
TR-ARRAY
TR-ARRAY
TR-ARRAY
LED
LED
LED
LED
PHOTO-COUPLER
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
Samsung Electronics
OUTDOOR MAIN PBA(DB92-02866A)
0604-001172
0604-001172
0801-000393
1006-001325
1201-002946
1203-002835
1203-002986
1203-004967
2007-000043
2007-000070
2007-000074
2007-000074
2007-000074
2007-000074
2007-000074
2007-000074
2007-000074
2007-000074
2007-000074
2007-000074
2007-000074
2007-000074
2007-000074
2007-000074
2007-000074
2007-000074
2007-000074
2007-000076
2007-000076
2007-000076
2007-000076
2007-000076
2007-000076
2007-000076
2007-000076
2007-000076
2007-000076
2007-000078
2007-000078
2007-000078
2007-000078
2007-000078
2007-000078
2007-000078
2007-000078
2007-000078
2007-000078
2007-000078
2007-000078
2007-000078
6-12
PC351
PC352
IC302
IC301
IC451
IC154
IC155
IC502
R424
R309
R152
R210
R213
R233
R234
R401
R402
R403
R404
R405
R406
R407
R420
R422
R516
R519
R562
R153
R255
R256
R257
R258
R352
R353
R512
R567
R904
R303
R307
R308
R351
R354
R503
R504
R505
R508
R509
R515
R529
R530
(cont.)
PHOTO-COUPLER
PHOTO-COUPLER
IC-CMOS LOGIC
IC-BUS TRANSCEIVER
IC-OP AMP
IC-POSI.FIXED REG.
IC-POSI.FIXED REG.
IC-VOL. DETECTOR
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
Samsung Electronics
OUTDOOR MAIN PBA(DB92-02866A) 2007-000078
2007-000078
2007-000078
2007-000078
2007-000078
2007-000080
2007-000082
2007-000084
2007-000084
2007-000084
2007-000084
2007-000084
2007-000084
2007-000084
2007-000084
2007-000084
2007-000084
2007-000084
2007-000084
2007-000084
2007-000084
2007-000084
2007-000084
2007-000084
2007-000084
2007-000084
2007-000084
2007-000084
2007-000084
2007-000084
2007-000084
2007-000084
2007-000084
2007-000084
2007-000084
2007-000090
2007-000090
2007-000090
2007-000090
2007-000090
2007-000090
2007-000090
2007-000090
2007-000090
2007-000090
2007-000090
2007-000090
2007-000090
2007-000090
2007-000109
6-12
R556
R557
R558
R560
R563
R522
R421
R211
R212
R214
R215
R216
R217
R218
R219
R220
R408
R501
R506
R507
R510
R511
R517
R518
R520
R521
R523
R524
R525
R526
R527
R534
R535
R536
R903
R301
R302
R304
R305
R528
R532
R533
R551
R552
R553
R554
R555
R559
R565
R531
(cont.)
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
Samsung Electronics
OUTDOOR MAIN PBA(DB92-02866A) 2007-000116
2007-000124
2007-000140
2007-000140
2007-000143
2007-000143
2007-000143
2007-000143
2007-000143
2007-000143
2007-000143
2007-000143
2007-000143
2007-000143
2007-000143
2007-000143
2007-000143
2007-000148
2007-000148
2007-000148
2007-000170
2007-000239
2007-000256
2007-000256
2007-000256
2007-000300
2007-000385
2007-000385
2007-000455
2007-000455
2007-000491
2007-000536
2007-000537
2007-000537
2007-000537
2007-000537
2007-000537
2007-000614
2007-000614
2007-000614
2007-000614
2007-000614
2007-000614
2007-000614
2007-000614
2007-000651
2007-000683
2007-000683
2007-000683
2007-000763
6-12
R306
R564
R202
R205
R207
R221
R222
R223
R224
R225
R226
R227
R228
R229
R230
R231
R232
R203
R204
R206
R201
R491
R455
R457
R468
R901
R101
R105
R251
R253
R561
R492
R154
R155
R156
R157
R158
R252
R254
R469
R470
R471
R472
R473
R474
R475
R454
R459
R466
R476
(cont.)
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
Samsung Electronics
OUTDOOR MAIN PBA(DB92-02866A) 2007-000763
2007-000872
2007-000872
2007-000872
2007-000924
2007-000924
2007-000924
2007-000924
2007-000924
2007-000924
2007-000979
2007-001071
2007-001175
2007-001175
2007-001175
2007-010245
2007-010245
2007-010245
2007-010245
2007-010245
2203-000236
2203-000257
2203-000257
2203-000257
2203-000257
2203-000257
2203-000257
2203-000257
2203-000257
2203-000257
2203-000440
2203-000440
2203-000440
2203-000440
2203-000440
2203-000440
2203-000440
2203-000440
2203-000440
2203-000440
2203-000440
2203-000440
2203-000440
2203-000440
2203-000440
2203-000440
2203-000440
2203-000783
2203-000783
2203-002002
6-12
R477
R801
R802
R803
R102
R103
R104
R106
R107
R108
R478
R902
R409
R423
R427
R410
R411
R412
R425
R426
C421
C222
C223
C224
C225
C301
C351
C352
C422
C423
C404
C405
C406
C408
C409
C410
C411
C501
C504
C505
C506
C507
C508
C510
C512
C523
C904
C455
C458
C453
(cont.)
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
C-CER,CHIP
C-CER,CHIP
C-CER,CHIP
C-CER,CHIP
C-CER,CHIP
C-CER,CHIP
C-CER,CHIP
C-CER,CHIP
C-CER,CHIP
C-CER,CHIP
C-CER,CHIP
C-CER,CHIP
C-CER,CHIP
C-CER,CHIP
C-CER,CHIP
C-CER,CHIP
C-CER,CHIP
C-CER,CHIP
C-CER,CHIP
C-CER,CHIP
C-CER,CHIP
C-CER,CHIP
C-CER,CHIP
C-CER,CHIP
C-CER,CHIP
C-CER,CHIP
C-CER,CHIP
C-CER,CHIP
C-CER,CHIP
C-CER,CHIP
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
Samsung Electronics
OUTDOOR MAIN PBA(DB92-02866A) 2203-002002
2203-002002
2203-002002
2203-002002
2203-002002
2203-002002
2203-002002
2203-002398
2203-005249
2203-005249
2203-005249
2203-005249
2203-005249
2203-005249
2203-005249
2203-005249
2203-005249
2203-005249
2203-005249
2203-005249
2203-005249
2203-005249
2203-005249
2203-005249
2203-005249
2203-005249
2203-005249
2203-005249
2203-005249
2203-005249
2203-005249
2203-005249
2203-005249
2203-005249
2203-005249
2203-005249
2203-005249
2203-005249
2203-005249
2203-005249
2203-005249
2203-005249
2203-005249
2203-005249
2203-005249
2203-005249
2203-005249
2203-005249
2203-006158
2203-006158
6-12
C454
C459
C515
C516
C517
C518
C519
C524
C061
C151
C152
C153
C154
C162
C163
C220
C221
C251
C252
C253
C254
C302
C303
C304
C305
C306
C307
C401
C402
C403
C407
C420
C424
C460
C503
C509
C511
C514
C520
C521
C525
C526
C527
C701
C702
C703
C704
C903
C201
C203
(cont.)
C-CER,CHIP
C-CER,CHIP
C-CER,CHIP
C-CER,CHIP
C-CER,CHIP
C-CER,CHIP
C-CER,CHIP
C-CER,CHIP
C-CER,CHIP
C-CER,CHIP
C-CER,CHIP
C-CER,CHIP
C-CER,CHIP
C-CER,CHIP
C-CER,CHIP
C-CER,CHIP
C-CER,CHIP
C-CER,CHIP
C-CER,CHIP
C-CER,CHIP
C-CER,CHIP
C-CER,CHIP
C-CER,CHIP
C-CER,CHIP
C-CER,CHIP
C-CER,CHIP
C-CER,CHIP
C-CER,CHIP
C-CER,CHIP
C-CER,CHIP
C-CER,CHIP
C-CER,CHIP
C-CER,CHIP
C-CER,CHIP
C-CER,CHIP
C-CER,CHIP
C-CER,CHIP
C-CER,CHIP
C-CER,CHIP
C-CER,CHIP
C-CER,CHIP
C-CER,CHIP
C-CER,CHIP
C-CER,CHIP
C-CER,CHIP
C-CER,CHIP
C-CER,CHIP
C-CER,CHIP
C-CER,CHIP
C-CER,CHIP
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
Samsung Electronics
OUTDOOR MAIN PBA(DB92-02866A) -
2203-006158
2203-006158
2203-006158
2203-006158
2203-006158
2203-006158
2203-006158
2203-006460
2203-006960
2203-007456
2203-007456
2203-007456
2203-007456
2203-007456
2203-007456
2203-007456
2203-007456
2203-007456
2402-001183
2402-001268
2402-001268
2402-001268
2402-001368
2402-001368
2402-001368
2802-001165
2802-001211
DB41-01227A
DB91-01517A
0903-001843
DB98-31449A
DB91-01534A
DB09-00596A
6-12
C204
C206
C207
C208
C210
C211
C212
C522
C902
C202
C205
C209
C213
C214
C226
C227
C228
C229
CE451
CE153
CE404
CE420
CE401
CE402
CE403
X201
X501
PCB MAIN
IC501
ASSY-LABEL
MICOM
IC201
-
(cont.)
C-CER,CHIP
C-CER,CHIP
C-CER,CHIP
C-CER,CHIP
C-CER,CHIP
C-CER,CHIP
C-CER,CHIP
C-CER,CHIP
C-CER,CHIP
C-CER,CHIP
C-CER,CHIP
C-CER,CHIP
C-CER,CHIP
C-CER,CHIP
C-CER,CHIP
C-CER,CHIP
C-CER,CHIP
C-CER,CHIP
C-AL,SMD
C-AL,SMD
C-AL,SMD
C-AL,SMD
C-AL,SMD
C-AL,SMD
C-AL,SMD
RESONATOR-CERAMIC
RESONATOR-CERAMIC
PCB MAIN
ASSY MICOM
IC-MICROCONTROLLER
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
ASSY-LABEL MICOM
1
ASSY MICOM
IC MICOM
1
1
Samsung Electronics
7. Wiring Diagram
7-1 Indoor Unit
Samsung Electronics
7-1
7-2 Outdoor Unit
7-2
Samsung Electronics
8-1 Indoor PCB
CN21
CN81
CN61
CN63
CN62
CN43
CN76
CN32
CN91
CN77
CN31
CN51
CN72
CN75
CN71
ķ CN61/CN62/CN63 STEP MOTOR
ĸ CN71 - POWER IN
Ĺ CN81 - SPI
ĺ CN51 - WI-FI MODULE
#1,#3 : AC220~240V
#1: SPI SIGNAL
#1: DC 12V
#2 : N.C
#3 : DC 12V
#1
#2
#3
#4
#5
#6
ļ CN43 - TEMPERATURE SENSOR
Ľ CN21 - COMMUNICATION
ľ CN72 - BLDC FAN MOTOR
#1,#2 : 485 COMM SIGNAL
#1
#2
#3
#4
#5
#6
#2~#5 :STEP MOTOR SIGNAL
Ļ CN51 - DISPLAY
#1~#11,#14,#17~#20 : MICOM DOWN #1,#2 : ROOM SENSOR
#12, #13, #15, #16 : N.C
#3,#4 : EVA MID SENSOR
#5,#6 : EVA IN SENSOR
Ŀ CN32 - FJM/NASA
CN75 - SMPS POWER IN
#1~#7, #11~ #14 : FJM/NASA SIGNAL#1,#3 : AC220~240V
CN76 - SMPS DC OUT
(12V/GND/5V)
:
:
:
:
:
:
:
:
:
:
:
:
WIFI UART SIGNAL1
WIFI UART SIGNAL2
WIFI RESET SIGNAL
GND
DC 12V
N.C
DC 310~340V
N.C
AGND
DC 15V
FAN RPM
FAN FEEDBACK
CN77 - SMPS DC OUT
(19V/GND/310V)
#1 : DC 5V
#1 : DC 310V~340V
#9 : GND
#2 : GND
#2,#3 : N.C
#10 : DC 12V
#3 : DC 12V
#4 : DC 19V~27V
#8 : DC 5V
#2 : N.C
#5 : AGND
CN31 - DOWNLOAD
DOWNLOAD
Samsung Electronics
8-1
8-2 Outdoor PCB
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
ķ CN151 - SMPS INV
ĸ CN204 - DRED
Ĺ CN201- DOWNLOAD-MAIN
ĺ CN251 - SENSOR
#1 : 15V
#2 : GND
#3 : ENABLE
#1
#2
#3
#4
#5
#1 ~ #20 : DOWNLAOD
#1,#2 : OUT SENSOR
#3,#4 : DISCHARGE SENSOR
#5,#6 : COND SENSOR
Ļ CN501 - EEPROM
ļ CN701 - EEV-A
Ľ CN152 - SMPS MAIN
ľ CN301 - COMMUNICATION
#1
#3
#4
#5
#6
#7
#1~#4 : EEV SIGNAL
#5 : 12V
#1 : 12V
#2 : GND
#3 : 5V
#1 : F1
#2 : F2
:
:
:
:
:
:
GND
5V
EEP CS
EEP_SO/MICOM RX
EEP_SI_MICOM_TX
EEP CLK
Ŀ CN901 - FAN
#1
#2
#3
#4
#5
#6
:
:
:
:
:
:
DC 310~340V
N.C
AGND
DC 15V
FAN RPM
FAN FEEDBACK
CN002 - POWER-L
#1 : L
8-2
: DRED1
: DRED2
: DRED3
: GND
: 5V
CN401- REACTOR
#1 : REACTOR1
#2 : REACTOR2
CN003 - EARTH
#1 : EARTH
CN030 - 4WAY
#1,#3 : AC220~240V
CN150 - SMPS AC
#1,#3 : AC220~240V
CN001 - POWER-N
#1 : N
CN402 - COMP
#1 : W
#2 : V
#3 : U
Samsung Electronics
8-3 Wire connecting the indoor unit terminal blocks
1.
Terminal press of Ring terminal shall be set facing up before connecting wire.
Is inverted
2.
There shall be no empty space between Ring terminal and Screw after Clamp.
If not, there exists a possibility of fire which can be caused by electric heat in the connecting part.
,
8-3
Terminalhasbeencut.
: Good
Bad : Ring terminal is connected reversely
Bad : Not clamped Screw
Bad : In the gap between Ring terminal & Screw
Bad : Unused Ring Terminal
Samsung Electronics
9. Operating Instructions
9-1 Name of Each Part
9-1-1 Indoor Unit
The design and shape are subject to change according to the model.
Ƶ Main
Parts
Room
temperature
sensor
Wi-Fi module
Air intake
SPi Lamp
(up and down)
(left and right)
Ƶ Display
Power indicator
Timer/Auto clean indicator
Power button
Samsung Electronics
Single user indicator
9-1
9-2 Wireless Remote Control-Buttons and Display
Remote controller display
Power
SPi
Mode
Set the SPi
Set one of the 5 operating modes
(see pages 15~16 for instructions).
Turbo / Soft
Quiet
Select Ultra turbo function or Soft function
Reduce noise generated from an indoor unit
during operation.
ECO Run
Vertical air swing
reduces energy usage while operating
in cool/heat mode.
automatically up and down.
Temp + Auto Clean
h
h
Fan
Increase/Decrease the temperature by 1 ˚C.
such as Auto/Low/Medium/High/Turbo.
Auto clean function – Dry inside of the
indoor unit to get rid of odor.
Horizontal air swing
d'light Cool
movement automatically left and right.
On Timer
Set the
Set the On Timer on.
mode on.
Set/Cancel
Set/Cancel the timer/
mode.
SMART Air conditioner Network.
2ndF
Switch the function of the button on the
remote controller.
Filter Reset
Reset the Filter Clean reminder
Usage
Display the amount of power consumption for few seconds on
the indoor unit display:
Time set
Set the current time
To silence the beep sound when pressing the button.
9-2
Samsung Electronics
10. Troubleshooting
10-1 Items to be checked first
1. The input voltage should be rating voltage ±10% range.
The air conditioner may not operate properly if the voltage is out of this range.
2. Is the line cable linking the indoor unit and the outdoor unit linked properly?
The indoor unit and the outdoor unit shall be linked by 5 cables.
Check the terminals if the indoor unit and outdoor unit are properly linked by the same number of cables.
Otherwise the air conditioner may not operate properly.
3. When a problem occurs due to the contents illustrated in the table below it is a symptom not related to the malfunction
of the air conditioner.
NO
Operation of air conditioner
Explanation
1
The OPERATION indication LED(BLUE) blinks when a
power plug of the indoor unit is plugged in for first
time.
2
In a COOL operation mode, the compressor does not
operate at a room temperature higher than the setting In happens after a delay of 3 minutes when the compressor is reoperated. The same phenomenon occurs when
temperature that the INDOOR FAN should operate.
a power is on. As a phenomenon that the compressor is
[ In case of heat pump model ]
reoperated after a delay of 3 minutes, the indoor fan is
In a HEAT operation mode, the compressor does not adjusted automatically with reference to a temperature of
operate at a room temperature lower than the setting the air blew.
temperature that indoor fan should operate.
3
Fan speed setting is not allowed in DRY
4
5
6
7
8
9
mode.
It indicates power is on. The LED stops blinking if the operation ON/OFF button on the remote control unit is pushed.
The speed of the indoor fan is set to LL in DRY mode.
Fan speed is selected automatically in AUTO mode.
Compressor operation is controlled automatically in DRY
mode depending on the room temperature and humidity.
Timer is being activated and the unit is in ready
Timer LED(ORANGE) of the indoor unit lights up and
mode. The unit operates normally if the timer operathe air conditioner does not operate.
tion is cancelled.
The compressor stops intermittently or the fan speed
The compressor stops intermittently in a COOL
of the indoor unit decreases to prevent inside/outside
mode or DRY mode, and fan speed of the indoor unit
air frozen depending on the inside/outside air temdecreases.
perature.
[In case of heat pump model]
When the unit is turned off while de-ice is activated,
Compressor of the outdoor unit is operating although the compressor continus operation for up to 9
minutes(maximum) until the deice is completed.
it is turned off in a HEAT mode.
The
compressor and indoor fan stop intermittently if
[In case of heat pump model]
room temperature exceeds a setting temperature in
The compressor and indoor fan stop intermittenly in order to protect the compressor from overheated air
HEAT mode.
in a HEAT mode.
Compressor stops operation intermittently in Dry
mode.
[In case of heat pump model]
Indoor fan and outdoor fan stop operation
intermittently in a HEAT mode.
Samsung Electronics
The compressor operates in a reverse cycle to remove
exterior ice in a HEAT mode, and indoor fan and outdoor fan do not operate intermittently for within 20%
of the total heater operation.
10-1
10-2 Communication Error
10-2-1 Communication Error
Indoor display
3-LED DISPLAY
LED1
◎
LED2
●
LED3
●
●
{
●
●
●
●
7-SEG DISPLAY
DESCRIPTION
E101/E102
Communication error(Indoor<->outdoor)
Outdoor display
◎
{
{
OLED ON
1min. Time out Comm.
Abnormal Communication
◎LED BLINKING {LED OFF
1. Checklist :
1) Is the cable between the indoor unit and outdoor unit connected correctly?
2) Isn't the power cable and communication cable cross?
2. Troubleshooting procedure
Restart after power off.
Is the communication error occurred again?
NO
Terminate the service.
YES
Is the connection of power cable and
communication cable normal?
NO
Correct the wrong cable.
YES
Is the power is normal?
(check the LED Lamp)
NO
Exchange the PBA of no power unit
YES
Exchange the indoor unit PBA.
YES
Is the communication error occurred again?
NO
Terminate the service.
YES
Exchange the outdoor unit PBA.
10-2
Samsung Electronics
10-2-2 Indoor temperature sensor Error
Indoor display
DESCRIPTION
7-SEG DISPLAY
E121
Indoor room temp sensor error
1. Checklist :
1) Is the indoor units temperature sensor connected correctly?
2) Is the sensor placed correctly?
3) Does the both terminal of sensor satisfy the resistance value in accordance with temperature?
2. Troubleshooting procedure
Detach the assembled sensor from the PBA sensor
connector and measure the sensor resistance with
ohmmeter(tester)
Is the sensor resistance value
10kohm±3% at the room temperature
of 25°C
NO
YES
Ass'y Sensor Replace
Sensor resistance value : 20°C- 12.09kohm
30°C - 8.31kohm
35°C - 6.94kohm
40°C- 5.83kohm
Connect the sensor to PBA connector (6piin)
Is the connection
ofthe
power
cableof #1-#2 in
supply power
and measure
voltage
and communication
cable normal?
the connector
Below 0.5V or Over 4.5V?
YES
Exchange the indoor PBA
NO
Micom error or connector check
YES
Exchange the indoor PBA
Samsung Electronics
10-3
10-2-3 Indoor Eva-in temperature sensor error
Indoor display
3-LED DISPLAY
LED1
◎
OLED ON
LED2
◎
LED3
{
7-SEG DISPLAY
DESCRIPTION
E122,E123
Indoor MID, Indoor IN PIPE-TH sensor error
◎LED BLINKING {LED OFF
1. Checklist :
1) Is the indoor units temperature sensor connected correctly?
2) Is the sensor placed correctly?
3) Does the both terminal of sensor satisfy the resistance value in accordance with temperature?
2. Troubleshooting procedure
Detach the assembled sensor from the PBA sensor
connector and measure the sensor resistance with
ohmmeter(tester)
Is the sensor resistance value
#3-#4 and #5-#6 10kohm±3% at the room
temperature of 25ఁ
NO
YES
Sensor Replace
Sensor resistance value : 20°C- 12.09kohm
30°C - 8.31kohm
35°C - 6.94kohm
40°C- 5.83kohm
Connect the sensor to PBA connector (6piin)
Is the connection
of power
cableof #3-#4
supply power
and measure
the voltage
and and
communication
cable normal?
#5-#6 in the connector
Below 0.5V or Over 4.5V?
YES
Exchange the indoor PBA
NO
Micom error or connector check
YES
Exchange the indoor PBA
10-4
Samsung Electronics
10-2-4 When the Up/Down, Left/Right, Grill louver motor does not operate (Initial Diagnosis)
(Not displayed)
1. Checklist :
1) Is the input power voltage normal?
2) Is the Up/Down louver motor properly connected with the connector? (CN61, CN62, CN63)
2. Troubleshooting procedure
Unplug the power cord and plug it after
30seconds later.
Is the lamp blinking?
NO
Check the as in the procedure.
No power.
NO
Connect the wire PBA to louver motor
YES
Is the connected louver wire?
YES
Does operation start when swing button of the
remote control unit pushed?
YES
Normal
NO
Is the voltage changeable at the pin#2~#5 of CN61,
CN62, CN63
(louver connector)?
NO
Exchange the PBA
YES
Up/Down louver motor is faulty.
Samsung Electronics
10-5
10-2-5 Indoor fan motor speed detecting error (BLDC fan)
Indoor display
3-LED DISPLAY
LED1
{
OLED ON
LED2
{
7-SEG DISPLAY
DESCRIPTION
E154
Indoor fan error
LED3
◎
◎LED BLINKING {LED OFF
1. Checklist :
1) Is the indoor units fan motor properly connected with the connector(CN72)?
2) Is the AC voltage correct?
2. Troubleshooting procedure
Restart after power off.
NO
Does the fan rotate?
Power off and Separate the Fan motor wire
from CN72 on Indoor PBA
YES
Is there short among
each pin #1~#6
Reassemble the fan wire and input the power again
YES
Exchange the Fan
motor
NO
Is the fan error appeared again?
NO
Terminate the
service
NO
Follow the check procedure of Indoor unit
power supply error check
NO
Exchange the Indoor PBA
YES
Is the voltage of CN72 #1-#3 over 250Vdc
YES
Is the voltage of CN72
#3-#5 and #3-#6 with in 1Vdc~15Vdc during
the operation?
YES
PBA problem or Motor problem
Change the PBA first and check the operation
Exchange the Fan motor
10-6
Samsung Electronics
10-2-6 Outdoor temperature sensor error
Indoor display
3-LED DISPLAY
LED1
Ƽ
7-SEG DISPLAY
LED2
LED3
Ƽ
E221
DESCRIPTION
Outdoor temperature sensor error
Outdoor display
Ƽ
LED ON
Ƽ
Ƽ LED BLINKING
Outdoor temperature sensor error
LED OFF
1.
Checklist :
1) Is the sensor connected correctly?
2) Is the sensor placed correctly?
3) Does the both terminal of sensor satisfy the resistance value in accordance with
4) Is the resistance value of sensor connection pull-up correct?
MODEL
AR09HSSDAWKXEU
2. Troubleshooting procedure
AR12HSSDAWKXEU
Is the sensor connector("A") connected
correctly in accordance with a color?
NO
temperature?
"A"
CN251
CN251
"B"
CN251 #1-#2
CN251 #1-#2
Reconnect the sensor connector.
YES
Is the sensor resistance value
"B" 10kohm±3% at the room temperature
of 25
NO
YES
Sensor Replace
Sensor resistance value : - 2012.09kohm
30 - 8.31kohm
35 - 6.94kohm
40 - 5.83kkohm
Connect the sensor to PBA connector
Is the
connection
of power
cable of
supply
power
and measure
the voltage
"B"in the connector
and communication
cable normal?
YES
Below 0.5Vdc or Over 4.5Vdc?
Exchange the Outdoor PBA
NO
Micom error or connector check
YES
Exchange the Outdoor PBA
Samsung Electronics
10-7
10-2-7 Outdoor Coil temperature sensor error
Indoor display
3-LED DISPLAY
LED1
Ƽ
7-SEG DISPLAY
LED2
LED3
Ƽ
E231
DESCRIPTION
Outdoor Cond temperature sensor error
Outdoor display
Ƽ
LED ON
Ƽ
Ƽ LED BLINKING
Outdoor Cond temperature sensor error
LED OFF
1.
Checklist :
1) Is the sensor connected correctly?
2) Is the sensor placed correctly?
3) Does the both terminal of sensor satisfy the resistance value in accordance with temperature?
4) Is the resistance value of sensor connection pull-up correct?
MODEL
"A"
"B"
AR09HSSDAWKXEU CN251 CN251 #5-#6
AR12HSSDAWKXEU CN251 CN251 #5-#6
2. Troubleshooting procedure
Is the sensor connector("A")
connected correctly in accordance
with a color?
NO
Reconnect the sensor connector.
YES
Is the sensor resistance value
"B" 10kohm±3% at the room temperature
of 25
NO
YES
Sensor Replace
12.09kohm
Sensor resistance value : - 20
30 - 8.31kohm
35 - 6.94kohm
40 - 5.83kohm
Connect the sensor to PBA connector
Is theand
connection
of power
cable
supply power
measure the
voltage
of "B"in the
connector
and communication
cable normal?
YES
Below 0.5Vdc or Over 4.5Vdc?
Exchange the Outdoor PBA
NO
Micom error or connector check
YES
Exchange the Outdoor PBA
10-8
Samsung Electronics
10-2-8 Outdoor Discharge temperature sensor error
Indoor display
3-LED DISPLAY
LED1
Ƽ
7-SEG DISPLAY
LED2
LED3
Ƽ
E251
DESCRIPTION
Outdoor Discharge temperature
sensor error
Outdoor display
Ƽ
LED ON
1.
Ƽ
Outdoor Discharge temperature sensor error
Ƽ LED BLINKING
LED OFF
Checklist :
1) Is the sensor connected correctly?
2) Is the sensor placed correctly?
3) Does the both terminal of sensor satisfy the resistance value in accordance with temperature?
4) Is the resistance value of sensor connection pull-up correct?
MODEL
AR09HSSDAWKXEU
AR12HSSDAWKXEU
2. Troubleshooting procedure
Is the sensor connector("A")
connected correctly in accordance
with a color?
NO
"A"
CN251
CN251
"B"
CN251 #3-#4
CN251 #3-#4
Reconnect the sensor connector.
YES
Is the sensor resistance value
"B" 200kohm±3% at the room temperature
of 25
NO
YES
Sensor Replace
Sensor resistance value : - 20242kohm
30 - 166ohm
35 - 138ohm
40 - 115kohm
Connect the sensor to PBA connector
Is theand
connection
of power
cable
supply power
measure the
voltage
of "B"in the
connector
and communication
cable normal?
YES
Below 0.5Vdc or Over 4.5Vdc?
Exchange the Outdoor PBA
NO
Micom error or connector check
YES
Exchange the Outdoor PBA
Samsung Electronics
10-9
10-2-9 Outdoor Discharge over temperature error
Indoor display
3-LED DISPLAY
LED1
Ƽ
LED2
7-SEG DISPLAY
LED3
Ƽ
E416
DESCRIPTION
Outdoor Discharge over temperature error
Outdoor display
Ƽ
LED ON
1.
Ƽ
Outdoor Discharge over temperature error
Ƽ LED BLINKING
LED OFF
Checklist :
1) Check the discharge temperature in the outdoor unit
2) Check the compressor locking or gas leak
3) Download the EEPROM data
2. Troubleshooting procedure
Restart after power off.
after 30min ~ 1Hr
Is the discharge over
temperature sensor error appeared
again?
NO
Terminate the service
YES
The condition is too poor for
air conditioner to operate .
Wait until discharge temperature is decreased
Restart after power off
Is the discharge over temperature
sensor error appeared again?
NO
Terminate the service
YES
Download the EEPROM data
Is the discharge over temperature
sensor error appeared again?
NO
Terminate the service
YES
Exchange the Outdoor PBA
Exchanged the Compressor
10-10
Samsung Electronics
10-2-10 Outdoor Fan motor error
Indoor display
3-LED DISPLAY
LED1
Ƽ
LED2
7-SEG DISPLAY
DESCRIPTION
E458
O u td o o r fan erro r
LED3
Ƽ
Outdoor display
Outdoor fan error
LED ON
1.
Ƽ LED BLINKING
LED OFF
Checklist :
1) Are the input power voltage and the power connection correct?
2) Is the motor wire connected to the outdoor PBA correctly?
3) Is there no assembly error or non-assembly in the terminal of motor wire connector?
4) Is there no obstacle at the surrounding of motor and propeller?
MODEL
AR09HSSDAWKXEU
AR12HSSDAWKXEU
2. Troubleshooting procedure
Restart after power off.
NO
Does the fan rotate?
"A"
CN90
CN90
Power off and Separate the Fan motor wire
from "A" on Outdoor PBA
YES
Is there short among
each pin #1~#6
Reassemble the fan wire and input the power again
YES
Exchange the Fan
motor
NO
Is the fan error appeared again?
NO
Terminate the
service
NO
Follow the check procedure of outdoor unit
power supply error check
NO
Exchange the Outdoor PBA
YES
Is the voltage of "A" #1-#3 over 250Vdc
YES
Is the voltage of "A" #3-#5 and
#3-#6 with in 1Vdc~15Vdc during
the operation?
YES
PBA problem or Motor problem
Change the PBA first and check the operation
Exchange the Fan motor
Samsung Electronics
10-11
10-2-11 Compressor starting error
Indoor display
3-LED DISPLAY
LED1
◎
LED2
{
LED3
◎
◎
{
7-SEG DISPLAY
DESCRIPTION
E461
Comp starting error
Outdoor display
{
OLED ON
Comp starting error
{LED OFF
◎LED BLINKING
1. Checklist :
1) Is the connection of cable for the compressor?
2) Is the compressor wire is connected clockwise? U(RED)-V(BLU)-W(YEL)
3) Is the interphase resistance of compressor normal?
2. Troubleshooting procedure
Restart after power off.
Is the restart error occurred again?
NO
Terminate the service
YES
Is the connection of compressor wire is normal?
NO
Connect the comp wire normally
YES
Download the EEPROM data
Is the restart error occurred again?
NO
Terminate the service
YES
Is the compressor body and interphase
resistance insulated?
NO
Exchange the Outdoor PBA
YES
Exchange the compressor
10-12
Samsung Electronics
10-2-12 Compressor wire missing error/rotation error
Indoor display
3-LED DISPLAY
LED1
◎
LED2
{
LED3
◎
{
O
7-SEG DISPLAY
DESCRIPTION
E467
Compressor wire missing
errorr/rotation error
Outdoor display
O
OLED ON
Compressor wire missing error/rotation error
{LED OFF
◎LED BLINKING
1. Checklist :
1) Is the connection of cable for the compressor?
2) Is the compressor wire is connected clockwise? U(RED)-V(BLU)-W(YEL)
3) Is the interphase resistance of compressor normal?
2. Troubleshooting procedure
Restart after power off.
Is the restart error occurred again?
NO
Terminate the service
YES
Is the connection of
compressor wire is normal?
(PBA and Compressor)
NO
Connect the comp wire normally
YES
Is the restart error occurred again?
NO
Terminate the service
YES
Is the compressor body and
interphase resistance insulated?
NO
Exchange the Outdoor PBA
YES
Exchange the compressor
Samsung Electronics
10-13
10-2-13 O.C(Over Current) error
Indoor display
3-LED DISPLAY
LED1
◎
LED2
{
LED3
◎
{
◎
7-SEG DISPLAY
DESCRIPTION
E464
IPM Over Current(O.C) Error
Outdoor display
{
OLED ON
IPM Over Current(O.C) Error
{LED OFF
◎LED BLINKING
1. Checklist :
1) Is the IPM Shunt resistance value correct? Check the resistor is opened
2) Is the condition of surrounding temperature abnormal overload?
3) Is there any problem as like the temperature sensor separation or measurement value error?
4) Is the interphase resistance of compressor normal?
2. Troubleshooting procedure
Restart after power off.
Is the O.C error occurred?
NO
Terminate the service
YES
Is the connection of compressor wire is normal?
NO
Connect the comp wire normally
YES
Is the O.C error occurred again?
NO
Terminate the service
YES
Is the condition of indoor/outdoor temperature
normal load?
NO
Restart after returning to the normal load
YES
Is the O.C error
occurred again?
10-14
Terminate the service
Samsung Electronics
Is the position of
temperature sensor and sensing
value normal?
Is the compressor body
and interphase resistance
insulated?
NO
NO
Correct the sensor position or
exchange the sensor
Exchange the Outdoor PBA
YES
Exchange the compressor
Samsung Electronics
10-15
10-2-14 DC_link voltage sensor error
Indoor display
3-LED DISPLAY
LED1
Ƽ
DESCRIPTION
7-SEG DISPLAY
LED2
LED3
Ƽ
Ƽ
Ƽ
E469
DC_link voltage sensor error
Outdoor display
LED ON
1.
Ƽ LED BLINKING
DC_link voltage sensor error
LED OFF
Checklist :
1) Is the input voltage of outdoor terminal block is normal?
2) Is the reactor wire connected?
3) Is the DC_link capacitor("A") assembled in accordance the specification? (Outdoor PBA)
4) Is the DC_link resistor("B") value is normal? (Outdoor PBA)
2. Troubleshooting procedure
M O D EL
AR09HSSDAWKXEU
AR12HSSDAWKNEU
Is the connected of reactor wire?
(PBA-Reactor)
"A "
CE101,CE102,CE103
CE101,CE102,CE103
NO
Connect the reactor wire
NO
Check the power input
NO
Exchange the Outdoor PBA
NO
Exchange the Outdoor PBA
"B "
R410,R411,R412
R410,R411,R412
YES
Restart after power off.
Start the operation (cooling mode or heating mode)
Is the DC_link
voltage ("A") is normal in operation mode?
Normal range(280Vdc~320Vdc)
YES
Is the DC_link
sensing voltage("B") is normal in operation mode?
Normal range (0.2Vdc~4.8Vdc)
YES
Is the reactor insulation damaged?
YES
Exchange the Reactor
10-16
Samsung Electronics
10-2-15 DC_link voltage sensor error
Indoor display
3-LED DISPLAY
LED1
Ƽ
DESCRIPTION
7-SEG DISPLAY
LED2
LED3
Ƽ
Ƽ
Ƽ
E488
AC Input Voltage Sensor Error
Outdoor display
LED ON
1.
Ƽ LED BLINKING
AC Input Voltage Sensor Error
LED OFF
Checklist :
1) Is the input voltage of outdoor terminal block is normal?
2) Is the reactor wire connected?
3) Is the PFC resistor("A") value is normal? (Outdoor PBA)
MODEL
AR09HSSDAWKXEU
AR12HSSDAWKXEU
2. Troubleshooting procedure
Is the connected of reactor wire?
(PBA-Reactor)
"A"
R105,R106,R107,R108
R105,R106,R107,R108
NO
Connect the reactor wire
NO
Exchange the Outdoor PBA
NO
Exchange the Outdoor PBA
"B"
R105
R105
YES
Restart after power off.
Start the operation (cooling mode or heating mode)
Is the DC_link sensing
voltage("B") is normal in operation mode?
Normal range (0.2Vdc~4.8Vdc)
YES
Is the reactor insulation damaged?
YES
Exchange the Reactor
Samsung Electronics
10-17
10-2-16 DC_link voltage under/over error, H/W DC-link Over voltage protection error/PFC over load
Indoor display
3-LED DISPLAY
LED1
LED2
DESCRIPTION
7-SEG DISPLAY
LED3
E466
DC-Link voltage under/over error
Ƽ
E483
E484
Over Voltage Protection Error
P FC o ver lo ad
Ƽ
Outdoor display
DC-Link voltage under/over error
PFC over load
Over Voltage Protection Erro
Ƽ
LED ON
1.
Ƽ LED BLINKING
LED OFF
Checklist :
1) Is the input voltage of outdoor terminal block is normal?
2) Is the input voltage is higher than 300Vac?
3) Is the reactor wire connected?
4) Is the DC_link capacitor(A") assembled in accordance the specification? (Outdoor PBA)
5) Is the DC_link resistor("B") value is normal? (Outdoor PBA)
M O D EL
"A "
6) Is the PFC resistor("C") value is normal? (Outdoor PBA)AR09HSSDAWKXER
CE101,CE102,CE103
AR12HSSDAWKXEU
CE101,CE102,CE103
"B "
R101,R102,R103,R104
R101,R102,R103,R104
M O D EL
AR09HSSDAXEUEU
AR12HSSDAWKXEU
"C "
R105,R106,R107,R108
R105,R106,R107,R108
"D "
R101,R105
R101,R105
2. Troubleshooting procedure
Is the connected of reactor wire?
(PBA-Reactor)
NO
Connect the reactor wire
NO
Check the input power in the powercord.
NO
Check the input power
YES
Restart after power off.
Is the the input voltage is nomal?
Normal range(180Vac ~ 270Vac)
YES
Restart after power off.
Start the operation (cooling mode or heating mode)
Is the DC_link voltage
("A") is normal in operation mode?
Normal range(280Vdc~320Vdc)
YES
10-18
Samsung Electronics
Is the DC_link sensing
voltage("D")is normal in operation mode?
Normal range (0.2Vdc~4.0Vdc)
NO
Exchange the Outdoor PBA
NO
Exchange the Outdoor PBA
YES
Is the reactor insulation damaged?
YES
Exchange the Reactor
Samsung Electronics
10-19
10-2-17 I_trip error, PFC over current
Indoor display
3-LED DISPLAY
LED1
Ƽ
LED2
7-SEG DISPLAY
LED3
Ƽ
E462
DESCRIPTION
AC Input I_Limit Trip Error
Outdoor display
Ƽ
LED ON
1.
AC Input I_Limit Trip Error
Ƽ LED BLINKING
LED OFF
Checklist :
1) Is the PFC Shunt("A") resistance value correct? Check the resistor is opened
2) Is the condition of surrounding temperature abnormal overload?
3) Is there any problem as like the temperature sensor separation or measurement value error?
4) Is the interphase resistance of compressor normal?
2. Troubleshooting procedure
MODEL
AR09HSSDAWK/EU
AR12HSSDAWK/EU
"A"
R425,R426
R425,R426
Restart after power off.
Is the condition of indoor/outdoor
temperature normal load?
NO
YES
Restart after returning to the normal load
Is the I_trip error
NO
occurred again?
Terminate the
service
YES
Is the position of
temperature sensor and the sensing
value normal?
NO
Correct the sensor position or
exchange the sensor
YES
Is the connection
cable for the compressor and power
terminal normal?
NO
Correct the cable connection
YES
Exchange the Outdoor PBA
10-20
Samsung Electronics
10-2-18 Current sensor error/Input current sensor error
Indoor display
3-LED DISPLAY
LED1
Ƽ
LED2
LED3
Ƽ
DESCRIPTION
7-SEG DISPLAY
E462
AC Input I_Limit Trip Error
Outdoor display
Ƽ
LED ON
1.
Current sensor error
Input current sensor error
Ƽ
Ƽ LED BLINKING
LED OFF
Checklist :
1) Is the PFC Shunt("A") resistance value correct? Check the resistor is opened
2) Is the IPM Shunt("B") resistance value correct? Check the resistor is opened
3) Is there no short or open around "C"?
2. Troubleshooting procedure
MODEL
AR09HSSDAWKXEU
AR12HSSDAWKXEU
Restart after power off.
Is the PFC shunt and IPM
shunt resistance value correct?
NO
"A"
R426,R425
R426,R425
"B"
R410,R411,R412
R410,R411,R412
"C"
IC451
IC451
Exchange the Outdoor PBA
YES
Is the current sensor error appeared again?
NO
Terminate the service
YES
Exchange the Outdoor PBA
Samsung Electronics
10-21
10-2-19 Heatsink sensor error/Heatsink over heat
Indoor display
3-LED DISPLAY
7-SEG DISPLAY
DESCRIPTION
E474
E500
Heatsink sensor error
Heatsink Over Temperature Error
LED1
LED2
LED3
◎
{
◎
◎
◎
O
Heatsink sensor error
◎
O
{
Heatsink Over Temperature Error
Outdoor display
OLED ON
◎LED BLINKING
{LED OFF
1. Checklist :
1) Are there screws assembly in PBA-heatsink?
2) Is the gap PBA-heatsink
3) Is the fan operation normal?
4) Is the cover assembly in control-box normal?
2. Troubleshooting procedure
Restart after power off.
Are there screws in PBA-heatsink?
(4 screws)
NO
Fastening the screw
YES
Is the fan operation normal?
NO
Check the fan connection
Change the Fan motor
YES
Exchange the Outdoor PBA
10-22
Samsung Electronics
10-2-20 Comp Vlimit error
Indoor display
3-LED DISPLAY
LED1
Ƽ
LED2
LED3
Ƽ
DESCRIPTION
7-SEG DISPLAY
E465
Comp V_limit/I_limit Error
Outdoor display
Ƽ
LED ON
1.
Comp V_limit/I_limit Error
Ƽ LED BLINKING
LED OFF
Checklist :
1) Is the IPM Shunt("A") resistance value correct? Check the resistor is opened
2) Is the condition of surrounding temperature abnormal overload?
3) Is there any problem as like the
ature
temper
sensor separation or measurement value error?
4) Is the interphase resistance of compressor normal?
2. Troubleshooting procedure
MODEL
AR09HSSDAWKXEU
AR12HSSDAWKXEU
"A"
R410,R411,R412
R410,R411,R412
Restart after power off.
Is the O.C error occurred?
NO
Terminate the service
NO
Connect the comp wire normally
NO
Terminate the service
NO
Restart after returning to the normal load
YES
Is the connection
of compressor wire is
normal?
YES
Is the Comp Vlimit error occurred again?
YES
Is the condition of
indoor/outdoor temperature
normal load?
YES
YES
Samsung Electronics
Is the O.C error NO
occurred again?
Terminate the
service
10-23
Is the position of
temperature sensor and sensing
value normal?
NO
Correct the sensor position or
exchange the sensor
YES
Exchange the Outdoor PBA
YES
Is the compressor
body and interphase resistance
insulated?
NO
Exchange the compressor
10-24
Samsung Electronics
10-2-21 EEPROM error/OTP error
Indoor display
3-LED DISPLAY
LED1
LED2
LED3
DESCRIPTION
7-SEG DISPLAY
E470
Ƽ
Ƽ
EEPROM Data Error (no data)
OTP errorEEPROM Data Error
(Main Micom Inv Micom)
E471
Outdoor display
Ƽ
LED ON
1.
Ƽ LED BLINKING
EEPROM Data Error (no data)
OTP errorEEPROM Data Error (Main MicomInv Micom)
LED OFF
Checklist :
1) Is there a short around micom?
2) Is there a short around "A"?
3) Did you download or insert EEPROM IC, after changing outdoor PBA?
2. Troubleshooting procedure
MODEL
AR09HSSDAWKXEU
AR12HSSDAWKXEU
power off and download EEPROM data
(or. Insert the service EEPROM IC)
Restart after power off
Is the error appeared again?
NO
"A"
CN501
CN501
Terminate the service
YES
Exchange the Outdoor PBA
Samsung Electronics
10-25
10-2-22 Operation condition secession error
Indoor display
3-LED DISPLAY
LED1
LED2
LED3
7-SEG DISPLAY
E440
{
◎
◎
E441
DESCRIPTION
Prohibit Operation Condition Error
(Heating)
Prohibit Operation Condition Error
(Cooling)
Outdoor display
O
OLED ON
{
◎
◎LED BLINKING
Operation condition secession
{LED OFF
1. Checklist :
1) Check the temperature around the outdoor unit.
2. Troubleshooting procedure
Restart after power off
Is the operation condition secession
error appeared again?
NO
Terminate the service
YES
* Heating mode *
Is the outdoor temperature over 40ఁ or
under -30ఁ?
* Cooling mode *
Is the outdoor temperature under -7ఁ
YES
The temperature condition is too poor to operate.
Wait until temperature is changed
10-26
Samsung Electronics
10-2-23 Gas leak error
Indoor display
3-LED DISPLAY
LED1
Ƽ
LED2
LED3
Ƽ
7-SEG DISPLAY
DESCRIPTION
E554
G A S Leak erro r
Outdoor display
GAS Leak error
LED ON
1.
Ƽ LED BLINKING
LED OFF
Checklist :
1) Is the position of indoor Eva_in sensor normal?
2) Check the pipe crack
3) Check the EEV valve connection("A") in Outdoor unit
4) Check the refrigerant was charged
MODEL
AR09HSSDAWK/EU
AR12HSSDAWK/EU
2. Troubleshooting procedure
Is the position of indoor eva
_in sensor normal?
NO
"A"
CN701
CN701
Indoor sensor take the normal position
YES
Restart after power off
after 20minutes later
Is the gas leak error appeared again?
NO
Terminate the service.
YES
Check the EEV valve operation.
Is the EEV valve connection normal?
NO
Connect the EEV valve.
YES
Is the EEV valve is operation?
Check the sound of EEV valve
after power on.
NO
Change the EEV valve.
YES
Samsung Electronics
10-27
Is the pressure of refrigerant normal?
NO
Check the pipe crack.
Fill up the refrigerant.
YES
Exchange the Indoor PBA
Exchange the Outdoor PBA
10-28
Samsung Electronics
102-24 No power outdoor (Initial Diagnosis) (Not displayed)
1.
Checklist :
1) Is input power normal?
2) Is AC power linked correctly? (L,N,E)
3) Is mis-wiring between communication wire and Power wire?
4) Is mis-wiring between Main PBA and SMPS PBA wire?
5) Is input voltage of SMPS AC in Main PBA (CN150) normal?
6) Is the voltage of SMPS DC in Main PBA (CN151,CN152) normal?
2. Troubleshooting procedure
Unplug the power cord
Is the power cable from
terminal block to PBA is correct?L :CN002, N:CN001,
EARTH:CN003
NO
Reconnect the power wire correctly.
YES
Check the fuse open or not? (F001)
NO
Exchange the Main PBA
YES
Restart after power off.
Is the power normal?
NO
Check the power source.
YES
Is AC power is normal for SMPS?
CN150 : 220Vac~240Vac
NO
Exchange the Main PBA
YES
Check SMPS wire connection
Samsung Electronics
10-29
After seperate SMPS DC
wire (3PIN RED, 3PIN BLU) from
Main PBA Connector CN151, CN152, Check
the DC voltage in SMPS PBA. Is the voltage is
normal in SMPS PBA?
(SMPS : CN002, CN003 Check)
NO
Exchange the SMPS PBA
YES
After connect SMPS
DC wire (3PIN RED, 3PIN BLU) with Main PBA
Connector CN151, CN152, Check the DC voltage in
Main PBA. Is the voltage is normal in Main PBA?
(Main : CN151,CN152 Check)
NO
Exchange the Main PBA
YES
Exchange the Main PBA, SMPS PBA
10-30
Samsung Electronics
10-2-25 No power outdoor (Initial Diagnosis) (Not displayed)
1.
Checklist :
1) Is input power normal?
2) Is AC power linked correctly? (L,N,E)
3) Is mis-wiring between communication wire and Power wire?
4) Is input voltage of SMPS DC-link capacitor("A") normal?
5) Is the voltage of SMPS DC normal?
2. Troubleshooting procedure
Unplug the power cord
Is the power cable from terminal block to
PBA is correct?L :"B", N:"C", EARTH:"D"
MODEL
AR09HSSDAWKXEU
AR12HSSDAWKXEU
"A"
CE101
CE101
"B"
TB-L
TB-L
"C"
TB-N
TB-N
"D"
EARTH
EARTH
MODEL
AR09HSSDAWKXEU
AR12HSSDAWKXEU
"E"
F001
F001
"F"
CE101
CE101
"G"
CE106
CE106
"H"
CE108
CE108
NO
Reconnect the power wire correctly.
NO
Exchange the PBA
NO
Check the power source.
NO
Exchange the PBA
NO
Exchange the PBA
YES
Check the fuse open or not? ("E")
YES
Restart after power off.
Is the power normal?
YES
Is the SMPS DC_link voltage normal?
"F":270Vdc~320Vdc
YES
Is the SMPS is normal?
"G" Main 5V : 4.5Vdc ~ 5.5Vdc
YES
Is the SMPS is normal?
"H" Main 12V : 11Vdc ~ 13Vdc
NO
Exchange the PBA
YES
Exchange the PBA
Samsung Electronics
10-31
10-2-26 AC zero cross signal error
Indoor display
3-LED DISPLAY
LED1
Ƽ
LED2
LED3
Ƽ
DESCRIPTION
7-SEG DISPLAY
E472
AC zero cross signal error
Outdoor display
Ƽ
LED ON
1.
Ƽ LED BLINKING
AC zero cross signal error
LED OFF
Checklist :
1) Check the power condition at customer's house (Is there any power noise?)
2) Have been there power failure?
2. Troubleshooting procedure
MODEL
AR09HSSDAWKNEU
AR12HSSDAWKNEU
Error display
X
X
Restart after power off
Is the AC line zero cross signal error appeared again?
NO
Terminate the service
YES
Exchange the Outdoor PBA
10-32
Samsung Electronics
10-2-27 AC zero cross signal error
Indoor display
3-LED DISPLAY
LED1
Ƽ
LED2
LED3
Ƽ
7-SEG DISPLAY
E556
DESCRIPTION
Capacity miss match error
Outdoor display
Ƽ
LED ON
1.
Capacity miss match error
Ƽ LED BLINKING
LED OFF
Checklist :
1) Check the Btu between indoor and outdoor unit
2) Check the indoor unit option and outdoor unit EEPROM data
MODEL
AR09HSSDBWKNEU
AR12HSSDBWKNEU
2. Troubleshooting procedure
Is the rated Btu between indoor unit
and outdoor unit?
NO
Error display
X
X
Exchange the one of them according
to the exact model spec
YES
Reset the option code again at indoor unit
Is the capacity miss match error appeared again?
NO
Terminate the service
YES
Download the EEPROM data
Is the capacity miss match error appeared again?
NO
Terminate the service
YES
Exchange the Outdoor PBA
Exchange the Indoor PBA
Samsung Electronics
10-33
10-2-28 When the remote control is not receiving
1. Checklist :
1) Check if the connector was normally assembled.
2) Check the battery in remote control
3) All the lights out and check again : Change electronic typed to a fluorescent light
4) Put the set in operation and check the voltage of display PBA
5) Replace the display PBA
10-34
Samsung Electronics
10-2-29 EEV or Valve Close error-Self diagnosis
Indoor display
3-LED DISPLAY
LED1
Ƽ
LED2
LED3
Ƽ
7-SEG DISPLAY
E422
DESCRIPTION
EEV or Valve Close error-Self diagnosis
Outdoor display
EEV or Valve Close error-Self diagnosis
LED ON
1.
Ƽ LED BLINKING
LED OFF
Checklist :
1) Is the position of indoor Eva_in sensor normal?
2) Check the pipe crack
3) Check the EEV valve connection("A") in Outdoor unit
4) Check the refrigerant was charged
MODEL
AR09HSSDAWKXEU
AR12HSSDAWKXEU
"A"
CN701
CN701
2. Troubleshooting procedure
Is the position of indoor eva_in sensor normal?
NO
Indoor sensor take the normal position
YES
Restart after power off
after 20minutes later
Is the gas leak error appeared again?
NO
Terminate the service.
YES
Check the EEV valve operation.
Is the EEV valve connection normal?
NO
Connect the EEV valve.
YES
Is the EEV valve is operation?
Check the sound of EEV valve after power on.
NO
Change the EEV valve.
YES
Is the pressure of refrigerant normal?
NO
Check the pipe crack.
Fill up the refrigerant.
YES
Exchange the Indoor PBA
Exchange the Outdoor PBA
Samsung Electronics
10-35
10-2-30 10-3-18 Smart Install error
1. Checklist :
1) Check the leakage region.(Use leakage detection liquid or soapy water)
2) When leakage region is found from service valve and piping connection flare nut part : After the related measures to check the
refrigerant supplements and operation.
3) If the leakage region is pipe welding part : Weld leakage region after refrigerant gas release.(Brass parts should only apply)
4) If the leakage region is surface area (Heat exchanger or pipe welding region is not) : Replace parts.
5) Check the PBA Relay
- Display of indoor unit : Ensure that the operating pilot lamp has been lighted.
- Ensure that the Relay input voltage of indoor unit PBA is normally.(If the PBA is defective, replace)
2. Troubleshooting procedure
Did stop valve of
the low pressure valve open
perfectly?
NO
Open perfectly stop valve.
(Use the 4mm hex wrench)
YES
Re-connect after 3 seconds,
after separate the power cord.
And then begin cooling operation with minimum
temperature that can establish. (use the remote control)
YES
Among compressor operation, does cold air
come out from the indoor unit?
YES
NO
Connect the manifold gauge to the service
port of low pressure side service valve and
then measure the refrigerant pressure.
YES
Does measurement
pressure include in ±10% extent
of reference pressure?
NO
YES
- Discharge temperature and the indoor
temperature measurements confirm
that the difference is more than 10ఁ.
- Fill up perfectly refrigerant after
re-vacuum.
[Execute the troubleshooting]
Check the refrigerant leaks.
Check the PCB Relay.
YES
YES
Execute the related troubleshooting.
End
10-36
Samsung Electronics
10-3 PCB Inspection Method
10-3-1 Pre-inspection Notices
1.
2.
3.
4.
Check if you pulled out the AC power plug when you eliminate the PCB or front panel.
Don't hold the PCB side not impose excessive force on it to eliminate the PCB.
Don’t pull the lead wire but hold the whole housing to connect or disconnect a connector to the PCB.
In case of outdoor PCB disassembly, check first the complete discharge of condenser after 1 minute power off.
10-3-2 Inspection procedure
1. Check connector connection and peeling of PCB or bronze coating pattern when you think the PCB is broken.
2. The PCB is composed of 3 parts.
. Indoor Main part : MICOM and surrounding circuit, relay, fan motor sensing and driving circuit, temperature sensing
circuit power circuit of SMPS, buzzer circuit. Communication circuit.
. Display part : LED lamp, Switch, Remote-control module.
. Outdoor Main part : MICOM and surround circuit, fan motor sensing and driving circuit, compressor driving circuit
power circuit of SMPS, PFC control circuit, 4way circuit, communication circuit,
OPTION.(EEV control circuit, temperature sensing circuit)
10-3-3 Indoor detailed inspection procedure
No
1
procedure
Plug out and pull the
PCB out of the control
box Check the PCB fuse.
Inspection Method
1) Is 1st fuse disconnected?
2) Is 2nd fuse disconnected?
Cause
. Over current.
. Indoor Fan motor short.
. AC part and pattern short of Indoor PBA.
Check the power voltage
2
Supply power
If the operating lamp
twinkles at this time ,
the above 1)~3) have no
relation.
1) Is the BD71 input voltage
200Vac ~240Vac?
. Power cord is fault, Fuse open, Wrong Power
cable Wiring, AC part is faulty.
2) Is the voltage between both
terminal of C111(+)-(-) 12Vdc?
. Switching Trans of Power circuit is faulty.
3) Is the voltage between both
terminal of C118(+)-(-) 5Vdc?
. Power circuit is faulty, Load short.
1) Is the voltage over DC 270V being
imposed on terminal #1~#3 of
. Fan motor of the indoor is faulty.
fanmotor connector(CN72)?
3
Press the ON/OFF button.
1. Fan speed(high)
2. Continuous Operation
Samsung Electronics
2) The fan motor of the indoor unit
doesn't run.
. Fan motor connector(CN72) is faulty.
3) The power voltage between
terminal #1-#3 of the
connector(CN72) is 0V.
. PBA is faulty.
10-37
㽞 New Function [ Indoor Terminal Block Safety Device ]
1. Thermal Fuse is installed in Terminal Block as below.
(Thermal Fuse is used to prevent PL caused by a defective connection of indoor and outdoor units)
Thermal Fuse
Connection of terminal block
and Main PBA
Terminal Block Internals
2. Thermal Fuse is opened when internal temperature of Terminal Block goes to a certain point due to Tracking caused by
a defective connection of indoor and outdoor units.
- When Thermal Fuse is opened, Main PBA (DC12V) is turned off and the indoor unit does not operate.
(There is no problem with Main PBA in this case)
- In the above case, the change of all-in-one Terminal Block will make Main PBA operate again.
Circuit Block
3. Measurement method of fair/defective thermal fuse
Fail
10-38
Defective
Samsung Electronics
11. Block Diagram
11-1 Indoor unit
CONTROLLER
IC-MCU
HEAT EXCHANGER SENSOR
·
·
·
·
·
·
·
·
·
·
ROOM TEMPERATURE SENSOR
HUMIDITY SENSOR
INFRARED SIGNAL
REMOTE CONTROL
DISPLAY PART
H/V BLADE CONTROL
INDOOR FAN MOTOR CONTROL
OUTDOOR COMMUNICATION
TEMPERATURE CONTROL
HUMIDITY CONTROL
TIMER
BUZZER CONTROL
WIFI MODEM COMMUNICATION
DISPLAY CONTROL
SPI
OSCILLATION
CIRCUIT
· DISPLAY
- TIMER
- GOODSLEEP
- COMFORT CARE
- 88 SEGMENT
· SPI
ZERO
VOLTAGE
DETECT
POWER ON/OFF
PWM
CONTROL
SIGNAL
MODE
(AUTO,COOL,DRY,FAN,
HEAT)
SPI SELECT
SMART SAVER SELECT
TURBO OPERATION
· STEPPING MOTOR
CONTROL SIGNAL
· SPI CONTROL SIGNAL
· BUZZZER CONTROL SIGNAL
PHOTO COUPLER
INDOOR FAN MOTOR
OVER
VOLTAGE
PROTECTION
QUIET OPERATION
TEMPERATURE
SELECT(UP/DOWN)
WI-FI MODEM
FAN SPEED SELECT
(H/M/L/AUTO)
COMMUNICATION
SIGNAL
BLADE-H/V
MOVING SELECT
OUTDOOR UNIT
d'LIGHT COOL SELECT
BUZZER
AUTO CLEAN SELECT
GOOD SLEEP SELECT
ON,OFF TIMER
SELECT(UP/DOWN)
· STEPPING MOTOR DRIVE
· SPI DRIVE
· BUZZER DRIVE
SPI
· STEPPING MOTOR
- BLDAE CONTROL(H/V)
TEMP/HUMI SELECT
BEEP ON/OFF SELECT
DISPLAY ON/OFF SELECT
DC12V
DC5V
SMPS POWER BLOCK
WPS MODE SELECT
DC5V
AP MODE SELECT
DC12V
DC15V
AC INPUT
Samsung Electronics
AC230V
11-1
11-2 Outdoor unit
11-2
Samsung Electronics
11-2-1 Pre-inspection Notices
1. Check if you pulled out the AC power plug when you eliminate the PCB or front panel
2. Don't hold the PCB side not impose excessive force on it to eliminate the PCB
3. Don’t pull the lead wire but hold the whole housing to connect or disconnect a connector to the PCB
4. In case of outdoor PCB disassembly, check first the complete discharge of condenser after 1 minute power off
11-2-2 Inspection procedure
1. Check connector connection and peeling of PCB or bronze coating pattern when you think the PCB is broken
2. The PCB is composed of 3 parts
• Indoor Main part : MICOM and surrounding circuit, relay, fan motor sensing and driving circuit, temperature sensing circuit power
circuit of SMPS, buzzer circuit. Communication circuit
• Display part : LED lamp, Switch, Remote-control module
• Outdoor Main part : MICOM and surround circuit, fan motor sensing and driving circuit, compressor driving circuit power
circuit of SMPS, PFC control circuit, 4way circuit, communication circuit, OPTION (EEV control circuit, temperature sensing circuit)
11-2-3 Indoor detailed inspection procedure
No
1
Procedure
Plug out and pull the PCB
out of the control box
Check the PCB fuse
Inspection Method
1) Is 1st fuse disconnected?
2) Is 2nd fuse disconnected?
Cause
. Over current
. Indoor Fan motor short
. AC part and pattern short of
Indoor PBA
Check the power voltage
2
3
Supply power
If the operating lamp twinkles at this time , the above
1)~3) have no relation
Press the ON/OFF button
1. Fan speed(high)
2. Continuous Operation
Samsung Electronics
1) Is the BD71 input voltage
200Vac~240Vac?
. Power cord is fault, Fuse open,
Wrong Power cable Wiring,
AC part is faulty
2) Is the voltage between both terminal of IC02 pin #1-#2 12Vdc?
. Switching Trans of Power circuit
is faulty
3) Is the voltage between both terminal of IC02 pin #2-#3 5Vdc?
. Power circuit is faulty, Load short
1) Is the voltage over AC 180V being
imposed on terminal #3-#5 of fan
motor connector (CN72)?
. Fan motor of the indoor is faulty
2) The fan motor of the indoor unit
doesn't run
. Fan motor connector(CN72) is
faulty
3) The power voltage between
terminal #3-#5 of the
connector(CN72) is 0V
. PBA is faulty
11-3
11-2-4 Outdoor detailed inspection procedure
No
1
2
3
4
11-4
procedure
Inspection Method
Plug out and pull the PCB out of
1) Is 1st fuse disconnected?
the control box
2) Is indoor PBA faulty?
Check the PCB fuse
(Wait 3 minutes after power off)
Check the Wiring
1) Is the Compressor wire connected
clockwise?
2) Is the Reactor wire connected
normal?
3) Is the Fan wire connected normal?
4) Is the 4way wire connected normal?
5) Is the sensor wire connected
Check the power voltage
1) Is the voltage between Terminal
block N(1)-1 200Vac~240Vac?
Cause
. Over current
. AC part and pattern short of Indoor
PBA
. AC part and pattern short of Outdoor
PBA
. Wrong assembly
. Installation(service) condition is bad
. Power cord is faulty, Indoor PBA
fault, Wrong Power cable Wiring
. L,N,E wire wrong wiring (Terminal
Block-PBA)
2) Is the PFC050(#26-#27) input
. Fuse open
voltage 200Vac~240Vac?
. PTC020 open
. RY021, RY022 is faulty
. Outdoor Micom(IC151) error
Supply power and operate the set
. Power circuit is faulty
3) Is the CE151 voltage 280Vdc~320dc?
(Use Remote-control, button in
. Load short
indoor set)
. PFC050 is faulty
3) Is the CE101 voltage 280Vdc~320dc?
. Reactor wire is wrong connection
. Switching Trans of Power circuit is
4) Is the voltage CE157 voltage 15Vdc? faulty
L d h t
. Switching Trans of Power circuit is
5) Is the voltage CE155 voltage 12Vdc? faulty
L d h t
. Switching Trans of Power circuit is
6) Is the voltage CE153 voltage
faulty
3.3Vdc?
. Load short
1) Normal : RED on, GRN blink, YEL off
2) Abnormal
. L,N,C wire wrong wiring
- All off : check no power
Check the LED lamp display
. Outdoor PBA is faulty
- abnormal display : check error
mode
Samsung Electronics
12. Reference Sheet
12-1 Low Refrigerant Pressure Distribution
Note : Please measure the refrigerant pressure after the air conditioner operates on testing cooling mode during more than
10 minutes.
■ Indoor Temp. Variation : 20°C ~ 32°C
■ Outdoor Temp. Variation : -5°C ~ 45°C
12-2 Pressure & Capacity mark
■ Power/Heat
W
cal/s
kcal/h
Btu/h
HP
kg.m/s
Ib.m/s
1
0.23885
0.85985
3.4121
0.001341
0.10197
0.73756
4.1868
1
3.6
14.286
0.0056146
0.42693
3.088
1.163
0.27778
1
3.9683
0.0015596
0.11859
0.85778
0.29307
0.06999
0.252
1
3.9302x10-4
0.029885
0.21616
745.7
178.11
641.19
2,544.4
1
76.04
550
9.8067
2.3423
8.4322
33.462
0.013151
1
7.233
1.3558
0.32383
1.0658
4.6262
0.0018182
0.13826
1
Samsung Electronics
12-1
12-3 Q & A for Non-trouble
Classification Class
Cooling
Q
The cooling is weak.
A
When it is hot outside, its cooling capacity decreases due to the increase of the ambient temperature.
When the dust filter gets blocked or warm outside air gets in, the cooling capacity will decrease. So,
make sure to clean the dust filter frequently, prevent heat loss by closing the doors and insulate the
cooling area by using curtains, blinds, shades or window tinting.
Q
The cooling is good generally. But, it gets weak when it is considerably hot.
A
It occurs when the outdoor unit is exposed to direct sun light and heat-up air is not ventilated well. So,
set up a sunblind over the outdoor unit and keep stuff away from the unit to increase the ventilation.
When the cooling capacity decreases during a heat wave, clean the heat exchanger of the outdoor unit
or spray some cold water to the heat exchanger to increase the cooling capability.
Q
The cooling is weak. Does it need refrigerant charging?
A
It is not correct charging refrigerant regularly. Except that you have moved in several times or the
connection pipes are broken, the refrigerant does not run low. So, when refrigerant is additionally
charged, it could be costly and cause a product's failure. When the refrigerant leaks, all of it will escape
in a short time resulting in cooling failure and no water coming out of the drain hose. So, if water comes
out from the drain hose, it indicates the normal operation of the product and it does not need
refrigerant charging.
Q
It fails to do cooling.
A
When the air conditioner is set to ventilation or the desired temperature is set higher than the current
temperature, it fails to do cooling. In this case, select cooling or set the desired temperature lower.
Q
A
It floods the floor.
Place the drain hose properly. When it is not placed properly, the drain water would flow back flooding
the floor. So, straighten out the drain hose for the water to be drained well.
Q
Water drips at the drain connection (service valve) of the outdoor unit.
A
When a glass bottle is taken out of the refrigerator, moisture gets condensed on its surface due to the
temperature differences. The same principle applies to the air conditioner. When cold refrigerant goes
through the copper tube, moisture gets condensed on the surface of the tube and the connection
areas. To prevent the water condensation, the pipes are insulated. But, the connection areas of the
outdoor unit are not insulated for the purpose of maintenance or repair, and water gets condensed due
to the temperature differences and drips down. Generally, it evaporates right away. But, when it drips
much during muggy days, put a water pan on the floor.
Q
It leaks even though a drain pump is used.
A
It occurs when the drain pump is plugged out or it is out of order. Check the power of the drain pump
and the position of the drain hose, and when the pump is faulty, contact the drain pump manufacturer.
Samsung Electronics do not manufacture drain pumps. So, we are not able to correct the drain pump
problems.
Q
Whenever the air conditioner is turned on, it irritates my eyes and gives me a headache.
A
There are no components in the air conditioner irritating the eyes and sending out chemical smells.
But, when the air conditioner is turned on, other smell sources are sucked into the air conditioner and
get out of it. So find and root out the smell sources. Generally, it occurs at a interior renovated place, a
pharmacy, a gasoline handling place, a tire shop, a second-hand book shop or an electronic component
handling place, when its chemical or musty smells are sucked in and sent out, it can be misled that the
air conditioner generates them.
Leakage
Smells
12-2
Description
Samsung Electronics
Classification Class
Smells
Operation
Description
Q
Whenever the air conditioner is turned on, it stinks.
A
When are no components in the air conditioner sending out chemical smells. But, when the air conditioner is turned on, other smell sources are sucked into the air conditioner and get out of it. So, find and
root out the smell sources. Generally, when the drain hose is taken out to the washing room or there
are sources of smells such as a diaper bin, a shoe shelf or a socks bin, bad smells generate. Also, it occurs
where glass cleaners or air fresheners are used; when they are sucked in interacting with dusts and
moistures inside, bad smells generate. these kinds of organic materials noxious to human bodies. So, we
recommend against the use of them.
Q
Whenever the air conditioner is turned on, it smells sour.
A
When the room is papered recently, its paste smells would be sucked inside. Also, when the air conditioner is installed in the study room of young boys loving sweat-generating activities such as the basketball, excessive sweats evaporate and get sucked into the air conditioner resulting in bad smells. So,
find and root out problem or refresh the room frequently.
Q
Whenever the air conditioner is turned on, it smells musty.
A
It is due to the improper keeping of the product after its use. When keeping the product, dry up the
inside with the operation of ventilation to prevent must. When the product is kept without drying up
the inside with ventilation, mold would grow inside resulting in must. So, open the windows and switch
on the ventilation function to get rid of the saturated smell inside.
Q
Whenever the air conditioner is turned on, it sends out bad smells such as stale smells.
A
It occurs generally when there are pet animals in the house. Their smells stay at the same place.
But, when the air conditioner is turned on, the air gets circulated resulting in the circulation of the
smells. So, find and root out the problem or refresh the room frequently.
Q
A
It sends out bad smells.
When the air filter is filthy, it could send out bad smells. So, clean the filter and ventilate the room with
the windows open while operating the ventilation function.
Q
It won't start.
A
There is a power failure or it is plugged out. Also, check if the power distribution panel is switched off.
Q
It goes off during operation.
A
When the hot air does not escape properly, it goes off during operation. it occurs when it does not ventilate properly because the outdoor unit is covered, the back of the outdoor unit is blocked by a cardboard or a plywood panel, and the front of the outdoor unit is blocked by the closed window or other
obstacles. Clear the above obstacles from the outdoor unit.
Q
It generally works properly. But, when it's considerably hot, it goes off during operation.
A
It occurs when the outdoor unit is exposed to direct sunlight and the hot air does not escape properly.
Set up a sun blind over the outdoor unit and clear the neighboring obstacles from the outdoor unit to
provide good ventilation. When it goes off frequently during a heat wave, it would prevent the turnoff and increase the cooling capacity cleaning the outdoor unit or spraying some water to the heat
exchanger.
Q
The remote controller won't operate.
A
When the batteries run out or the transmitter or receiver of the remote controller is blocked by obstacles, change the batteries or keep the obstacles away from the controlling area. Also, the remote controller may mot work under intensive light from a 3-wave length lamp or a neon sign due to the EMI. In
this case, take the remote controller closer to the receiver.
Samsung Electronics
12-3
Classification Class
Q
Who installs the air conditioner? (Relocation/Re-installation)
A
When relocating or re-installing the air conditioner, make sure to contact Samsung Electronics Service
Center or Authorized Service Agent and have them to do the job. (If not, it could cause personal injury
or product damage.)
The cost for the relocation/re-installation of the air conditioner is subject to the customer's expense.
There is a cost table. But, our service engineer needs to visit to total up the cost correctly.
When you move in, make sure to contact Samsung Electronics Service Center or Authorized Service
Agent in advance to streamline the process.
Q
Is it possible to install the outdoor unit outside?
A
It is possible to install it at a designated place in the apartment or on the rooftop nearby.
But, it's illegal hanging an angle iron case with the outdoor unit in it outside the apartment.
Also, it is illegal obstructing passers-by with the outdoor unit installed outside.
Q
What can be done to install the outdoor unit facing the road because it is a commercial
building?
The following is an excerpt from building code going into effect from JUNE 1 st 2005. "The exhaust pipe
of a cooling or ventilation facility installed in a building adjacent to the streets of commercial or residential areas shall bel installed higher than 2 m to prevent the exhaust air from blowing directly to passersby and the current facilities shall be corrected by MAY 31 st 2005." So, please install it higher than 2 m or
not to blow the hot exhausting air directly to passers-by.
What about installing a windscreen during installation not to blow hot air directly to passers-by?
When the hot air from the front of the outdoor unit is blocked, the product's performance will be affected and it will fail to operate properly. So, keep it at least 300mm away from its surrounding walls and
give it good ventilation.
Installation
A
Q
A
12-4
Description
Samsung Electronics
12-4 Cleaning /Filter Change
12-4-1 Cleaning your Air Conditioner
To get the best possible use out of your air conditioner, you must clean it regularly to remove the dust that accumulates on
the air filter.
Removing the Air filter
Air filter
There is a hole on the bottom right side of the filter. Put your finger in that hole
to get a grip on the filter and slightly push it up to release the hooks from the
bottom side. Then, pull it down to remove the filter from the main body.
Cleaning the air filter
Washable foam based air filter captures large particles from the air. The filter is cleaned with a vacuum or by hand washing.
Remove the air filter from the main body.
Clean the Air filter with a vacuum cleaner or soft brush.
If dust is too heavy, rinse it with running water.
Insert the air filter back in its original position.
Dry the Air filter in a ventilated area.
t $MFBOUIF"JSöMUFSFWFSZXFFLT$MFBOJOHUFSNNBZEJòFSEFQFOEJOHPOUIFVTBHFBOEFOWJSPONFOUBMDPOEJUJPOT*OEVTUZBSFBDMFBO
it once a week.
t *GUIF"JSöMUFSESJFTJOBDPOöOFEPSIVNJE
BSFBPEPSTNBZHFOFSBUF*GJUPDDVSTSFDMFBOBOEESZJUJOBXFMMWFOUJMBUFEBSFB
t 8IFOUIFöMUFSDMFBOSFNJOEFSJTPOQMFBTFQSFTTUIFOE'CVUUPOBOEUIFOQSFTTUIF&$03VOCVUUPOPOSFNPUFDPOUSPMMFS
Samsung Electronics
12-5
12-5 Installation
12-5-1 Before Installation
Keep the air conditioner outlet and inlet free from its surroundings.
In case of installation, keep the symmetry and fix it to prevent vibration.
The pipe length shall meet the standard as far as possible.
12-5-2 Installation Procedure
■ Location
Install the product in an area to guarantee the best cooling effect, convenience of piping and electric work, and
inexistence of vibration or wind.
■ Wall Drilling
Drill the wall downward in a diameter of 60 to 65mm.
■ Fixing Indoor Unit & Outdoor Unit
Fix the air conditioner indoor unit securely to the wall. Secure the outdoor unit in a suitable position.
■ Pipe Spooling & Connectingt
You shall cut the pipe with a pipe cutter and grind all the burrs of the cut surface.
pipe expansion may continue until the pipe surface becomes uneven or torn apart.
Be sure to use a torque wrench to tighten pipes or flare nuts.
<Torque & Depth>
Outer Diameter (D)
Torque(kgf·cm)
Depth(A)
ø6.35 mm(1/4")
140~170
1.3 mm
ø9.52 mm(3/8")
250~280
1.8 mm
ø12.70 mm(1/2")
380~420
2.0 mm
ø15.88 mm(5/8")
440~480
2.2 mm
ø19.05 mm(4/4")
9900~1,210
2.2 mm
Pipe
Flare
■ Leak Test
Put an inset gas like nitrogen in the outdoor unit pipe and put soap bubbles or other test liquids on the pipe surface for
the leak test.
■ Drain Hose Connecting
Install the drain hose downward to drain water naturally. Be sure to pour water into the hose to check if it drains well.
■ Electric & Earth Work
Electric and earth work shall meet the "Electric Facility Technology Standard" and the "Internal Wire Regulation" of the
Electric Business Laws.
■ Inspection & Trial Run
Upon completion of the tests, you shall make a trial run while you explain the main functions of the air conditioner to
finish the installation.
12-6
Samsung Electronics
12-6 Installation Diagram of Indoor Unit and Outdoor Unit
12-6-1 Air-Purge Procedure
1) Connect each assembly pipe to the appropriate valve on
the outdoor unit and tighten the flare nut.
Indoor unit
Outdoor unit
A
Gas pipe side
B
Liquid pipe side D
C
2) Connect the charging hose of low pressure side of
manifold gauge to the packed valve having a
service port (3/8" Packed valve) as shown at the
figure.
3) Open the valve of the low pressure side of manifold
gauge counter-clockwise.
4) Purge the air from the system using vacuum pump for
about 30 minutes.
- After that, please recheck that pressure is stabilized.
- Close the valve of the low pressure side of manifold
gauge clockwise.
- Remove the hose of the low pressure side
of manifold gauge.
5) Set valve cork of both liquid side and gas side of packed
valve to the open position.
6) Mount the valve stem nuts to the 2 way and
3 way valve. And mount the service port cap to
3 way valve.
Vacuum Pump
Valve stem
Stem cap
7) Check for gas leakage.
- At this time, especially check for gas
leakage from the 3 way valve's stem nuts,
and from the service port cap.
A
(gas)
B
(liquid)
Samsung Electronics
12-7
12-6-2 "Pump down" Procedure
Pump down will be carried out when an evaporator is replaced or when the unit is relocated in another area.
1) Remove the caps from the 3 way valve and the
3 way valve.
2) Turn the 3 way valve clockwise to close and
connect a pressure gauge (low pressure side)
to the service valve, and open the 3 way valve
again.
3 way Valve
2 way Valve
3) Set the unit to cool operation mode.
(Check if the compressor is operating.)
4) Turn the 3 way valve clockwise to close.
5) When the pressure gauge indicates "0" turn the
3 way valve clockwise to close.
6) Stop operation of the air conditioner.
7) Close the cap of each valve.
Relocation of the air conditioner
t3FGFSUPUIJTQSPDFEVSFXIFOUIFVOJUJTSFMPDBUFE
t$BSSZPVUUIFQVNQEPXOQSPDFEVSFSFGFSUPUIFEFUBJMTPGAQVNQEPXOh
t3FNPWFUIFQPXFSDPSE
t%JTDPOOFDUUIFBTTFNCMZDBCMFGSPNUIFJOEPPSBOEPVUEPPSVOJUT
t3FNPWFUIFGMBSFOVUDPOOFDUJOHUIFJOEPPSVOJUBOEUIFQJQF
t"UUIJTUJNFDPWFSUIFQJQFPGUIFJOEPPSVOJUBOEUIFPUIFSQJQFVTJOHBDBQPSWJOZMQMVHUPBWPJEGPSFJHONBUFSJBM
entering.
t%JTDPOOFDUUIFQJQFDPOOFDUFEUPUIFPVUEPPSVOJU At this time, cover the valve of the outdoor unit and the other pipe using a cap or vinyl plug to avoid foreign
material entering.
t.BLFTVSFZPVEPOPUCFOEUIFDPOOFDUJPOQJQFTJOUIFNJEEMFBOETUPSFUPHFUIFSXJUIUIFDBCMFT
t.PWFUIFJOEPPSBOEPVUEPPSVOJUTUPBOFXMPDBUJPO
t3FNPWFUIFNPVOUJOHQMBUFGPSUIFJOEPPSVOJUBOENPWFJUUPBOFXMPDBUJPO
12-8
Samsung Electronics
1nd
2nd
Project
A
R
A
R
ITEM
RAC
FAC
WAC
3rd
4th
Capacity
0
9
1
2
1ST
A
A
A
2ND
R
F
W
5th
Sell
H
H
Item
1
2
3
4
5
6th
7th
Feature
S
S
S
S
Reference
Export
Export
Export
Export
Export
8th
9th
Series
D
A
D
A
3TH 4TH
0
9
1
2
1
8
2
4
3
0
Item 5TH
12Year E
13Year F
14Year H
15Year J
16Year K
Item1
7TH
Export The virus doctor (The India / Latin America A / PAC K besides) S
Export NO virus doctor (the India / Latin America A / PAC K besides) F
Special instructions:
About AR**FSFNAWK/FA ,the 7TH is “S”, but there is no virus doctor in these models.
Item 1
Export
Export
Export
Export
Item 2
RAC
RAC
RAC
RAC
Item 3
FMC FLG (Best)
FMC DLX (Better)
FMC STD (Good1)
FMC ENT (Good2)
1ST
1ST
1ST
1ST
A3050
12th
Unit
N/X
N/X
13th 14th
Export
E
U
E
U
Item
6TH
INVERTER HP S
INVERTER CO V
9TH DIGIT
Export 1st MODEL
2nd
Export
Export 3rd MODEL
Export 4th MODEL
Export 5th MODEL
A
B
C
D
E
8TH
9TH
MODEL F
MODEL D
MODEL S
MODEL N
Division Series Project Color Name Division component
F
F
D
D
S
S
N
N
10th 11th
Color
W
K
W
K
Twilight
Best
Best
TBD
Twilight
Better
Better
TBD
Twilight
Good1
Good1 Midnight Blue
Twilight
Good2
Good2
TBD
Grille
Grille
Grille
Grille
Grille
Deco
Grille
Grille
Sinkeolreo code
Remark
(10TH,11TH)
WK
TBD
WK
TBD
WK
Deco : Transparency
Grille : Twilight
UR
WK
TBD
Grille : Metalic Gray
Item1 Item2 12TH
/
Export SET
N
Export IN
Export OUT
X
Item
1
The existing code The sales area
XEU
Europe
CIS Desription
Europe(XEU)
The integrated code
(13TH,14TH
EU
GSPN (GLOBAL SERVICE PARTNER NETWORK)
Area
Web Site
Europe, CIS, Mideast & Africa gspn1.samsungcsportal.com
Asia
gspn2.samsungcsportal.com
North & Latin America
gspn3.samsungcsportal.com
China
china.samsungportal.com
This Service Manual is a property of Samsung Electronics Co., Ltd.
Any unauthorized use of Manual can be punished under applicable
International and/or domestic law.
© Samsung Electronics Co., Ltd. August. 2013.
Code No. AC-00045K_1
">