Sharp | KB-6100NS | Installation manual | Sharp KB-6100NS Installation manual

Warming Drawer
Installation Manual
SPECIAL WARNING
INSTALLATION AND SERVICE MUST BE PERFORMED BY A QUALIFIED INSTALLER.
IMPORTANT: SAVE this installation manual FOR LOCAL ELECTRICAL INSPECTOR’S USE.
READ AND SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.
Clearances and dimensions
For SAFETY CONSIDERATIONS do not install drawer in any combustible cabinetry, which is not in accordance
with the stated clearances and dimensions on page 2. See Figures 1 and 2.
Unpacking your Warming Drawer
Important notes to the Consumer
• Prepare an adjacent
a rea on t he f lo or
next to the shipping
carton with protective
material. Open the
top of the carton and
lift Warming Drawer
up and out on to the
protective material.
Keep this manual with your Operation Manual for future
reference.
Drawer Guides
• As when using any Warming Drawer oven generating heat,
there are certain safety precautions you should follow. These
are listed in the Operation Manual. Read all and follow
carefully.
• Be sure your Warming Drawer is installed and grounded
properly by a qualified installer or service technician.
• Remove all packing
material and tape from
the product.
• Locate the operation
and installation manual
that also includes four
(4) mounting screws.
Name Plate
Variable Humidity
Control
Air Vents
• Follow all instructions
in the installation
manual to complete
installation.
Important
notes to the installer
Important Safety Instructions
If the information in this manual is not followed
exactly, a fire or electrical shock may result that could cause
property damage, personal injury or death.
To reduce the risk of tipping, the Warming
Drawer must be secured by a properly installed Anti-Tip
block.
• This Warming Drawer must be electrically grounded in
accordance with local codes.
• Make sure the wall coverings and the cabinets around the
Warming Drawer can withstand the heat generated by the
Warming Drawer.
• Read all of the Installation Manual before installing the
Warming Drawer.
Never leave children alone or unattended in the
area where a Warming Drawer is in use. Never leave the drawer
open when the Warming Drawer is unattended.
• Observe all governing codes and ordinances.
Stepping, leaning or sitting on the drawer
may result in serious injuries and can also cause damage to the
Warming Drawer.
• Remove all packing material before connecting the electrical
supply.
• Be sure to leave these instructions with the consumer.
• Do not use the Warming Drawer as a storage space. This
creates a potentially hazardous situation.
CLEARANCES AND DIMENSIONS
• Dimensions that are shown in Figures 1 and 2 must be used.
Given dimensions provide minimum clearance. The electrical
outlet can be located in the shaded areas shown in Figure 6.
• Check location where the Warming Drawer will be installed
for proper electrical supply.
• Your oven can be built into a cabinet or wall by itself or under
a gas/electric wall oven, or Warming Drawer.
• Contact surface must be solid and level. Pay special attention
to the floor on which the Warming Drawer will sit. The floor of
the opening should be constructed of plywood strong enough
to support the weight of the oven (about 100 pounds).
• Be sure that the clearance of the floor between the wall oven
and the Warming Drawer is a minimum of 2-inches.
Warming Drawer Measurements
1 "x 1 "
Anti-Tip
block
6"
28 "
opening
Allow "
overlap
23 "
min depth
Allow
5
/8"
overlap 9 1/8" opening
Allow "
overlap
36"
countertop
height
10 "
28 "
9 "
8 "
9" to bottom
of Anti-Tip
block
23"
Figure 3
30"
Floor must
support 100 lbs.
Allow
"
overlap.
24 " to top of floor
(recommended)
Figures 1, 2 and 4 contain many
Warming Drawer measurements
for reference when planning the
drawer’s location. See Figure 5, 84"
page 3, for suggested Warming wall
cabinet
Drawer electrical layout.
30"
cabinet min.
Figure 1
Optional Microwave
Drawer Cutout
illustrated in sketch.
Electrical outlet
location
6"
1 "x 1 "
Anti-Tip
block
3 "
5"
4"
28 "
opening
Floor must
support
100 lbs.
"
Allow
overlap.
23 "
min depth
Allow "
overlap.
36"
countertop
height
28 "
opening
Allow "
overlap.
Allow
"
overlap.
14
"
opening
Allow
"
overlap.
Allow "
overlap.
1 "x 1 "
Anti-Tip
block
(6")
14
"
to bottom
of Anti-Tip
block
1 "x 1 "
Anti-Tip
block
28 "
opening
Allow "
overlap.
2" min.
23 "
min depth
Allow "
overlap.
Allow
5
Floor must
/8"
overlap 9 1/8" opening support
100 lbs.
30"
cabinet min.
Figure 4
E2
Floor must
support 100 lbs.
24 " to top of floor
(recommended)
Allow
7 " to top of floor
"
overlap. (recommended)
Figure 2
9" to bottom
of Anti-Tip
block
Allow
5
/8"
overlap 9 1/8" opening
Allow
"
overlap.
9"
2" min.
23 "
min depth
30"
cabinet min.
Optional
wall oven
cutout
illustrated
in sketch
ANTI-TIP BLOCK
Electrical Outlet
NORMAL INSTALLATION STEPS
The electrical requirements are a 120 volt 60 Hz, AC only, 15
amp. or more protected electrical supply. It is recommended that
a separate circuit serving only this appliance be provided.
Anti-Tip BLOCK Installation Instructions
To reduce the risk of tipping of the drawer, the Anti-Tip block
must be properly installed located 9-inches above the floor on
which the Warming Drawer will sit. The 6-inch Anti-Tip block
must be provided by the installer. See Figures 1, 2, and 4. The
Anti-Tip block prevents serious injury that might result from
spilled hot liquids.
The drawer is equipped with a 3-prong grounding plug. It must
be plugged into a wall receptacle that is properly installed and
grounded. Should you only have a 2-prong outlet, have a qualified
electrician install a correct wall receptacle.
Note: If you have any questions about the grounding or electrical
instructions, consult a qualified electrician or service person.
If the Warming Drawer is ever moved to a different location, the
Anti-Tip block must also be moved and installed. When installed
to the wall, make sure that the screws completely penetrate the dry
wall and are secured in wood or metal so that the block is totally
stable. When fastening, be sure that the screws do not penetrate
electrical wiring or plumbing.
10"
Electrical
outlet zone
10"
6"
centerline
10"
6" (153 mm)
5"
Anti-tip
Block
Solid
Floor
9" (228.6 mm)
38"
5"
9" cutout opening
Locate outlet in available space
adjacent to the warming drawer.
10"
10"
4"
Figure
(101.6 mm)
1½" x 1½"
Anti-tip
Figure 6
30"
5
Grounding Instructions
Permanent and Correct Installation
This appliance must be grounded. The Warming Drawer is equipped with a cord having a grounding
wire with a grounding plug. It must be plugged into a wall receptacle that is properly installed
and grounded in accordance with the National Electrical Code and local codes and ordinances.
In the event of an electrical short circuit, grounding reduces risk of electric shock by providing
an escape wire for the electric current.
– Improper use of the grounding plug can result in a risk of electric shock. Do
not use an extension cord. If the power supply cord is too short, have a qualified electrician or
serviceman install an outlet near the appliance.
3-Prong Plug
Grounding Pin
3-Prong Receptacle
Grounded Receptacle Box
Drawer Installation
• Carefully guide the drawer into the prepared opening. Avoid
pinching the cord between the oven and the wall.
• Slide the drawer all the way until the mounting flange is flush
with the face of the cabinet.
• Open the drawer. Using the 4 holes on the drawer as a template,
predrill the cabinet using a 1/16" bit. See Figure 7A.
• Secure the drawer with the 4 screws supplied. See Figure 7B.
• Plug the power supply cord into the electrical outlet.
Parts Supplied
Figure 7A
Figure 8A
4 Screws
Figure 7B
E3
Model & Serial Number Location
Before you call for Service
The name plate, including model and serial number, is located
on the right side of the Warming Drawer.
Read the BEFORE YOU CALL and operating instruction sections
in your Operation Manual. It may save you time and expense.
The list includes common occurrences that are not the result of
defective workmanship or materials in this range.
Refer to the warranty in your Operation Manual for Sharp’s
toll-free service number and address. Please call or write if you
have inquiries about your Warming Drawer product and/or need
to order parts.
Care, Cleaning and Maintenance
Refer to the Operation Manual for cleaning instructions.
SHARP ELECTRONICS CORPORATION
TINSEB521MRR0
Sharp Plaza, Mahwah, New Jersey 07495-1163
1-800-BE-SHARP (237-4277)
E4
Printed in USA
Download PDF

advertising