TruVision 700TVL and 720TVL Analog Cameras (TVB

TruVision IR Bullet Camera
TVB-2201/TVB-4201 and
TVB-2202/TVB-4202
Installation Guide
P/N 1072924 • REV A • ISS 10FEB15
Content
Product overview 2
Camera description 4
Installation 4
Specifications 6
Regulatory Information 7
Product overview
This is the TruVision IR Bullet Camera Installation
Guide for models TVB-2201 / TVB-2202 / TVB-4201
/ TVB-4202. This guide describes a standard
installation.
2
Installation Guide
Package contents:

Camera with power
and video output
cables

3 M4 screws (3 x
25 mm) and 4 dry
wall anchors (Ø7.5
x 24.5 mm) for wall
or ceiling
installation

Template

CD

Installation Guide
•
WEEE and Battery
Disposal
Installation Guide
3
Camera description
1
3
4
2
5
6
1. Video cable
4. Sun shield
2. Power cable
5. Lens
3. Mounting base
6. IR LED
Installation
To install the camera:
1.
4
Using the template, place it level against the
mounting surface and mark the position of the
mounting holes.
Installation Guide
Drill Template
2.
Following all local codes, drill and prepare the
mounting holes.
3.
Securely fasten the mount to the mounting
surface with the supplied screws.
4.
Connect a 75-ohm coaxial video cable to the
video cable and a 12 VDC power supply to the
power cable.
5.
Loosen the bracket screws and then adjust the
camera position and angle as required.
Installation Guide
5
360°
90°
360°
6.
Retighten the bracket screws.
Specifications
6
Power supply
12 VDC
Current
Max. 330 mA
Power
consumption
1.8 W max.(Max. 4 W with
IR cut filter on)
Weight
0.79 lb. (360 g)
Dimensions
(Ø × L)
2.76 x 5.89 in.
(70 x 149.5 mm)
Installation Guide
Regulatory Information
Copyright:
© 2015 United Technologies Corporation.
Interlogix is part of UTC Building & Industrial Systems, a unit of
United Technologies Corporation. All rights reserved.
Trademarks and patents:
Trade names used in this document may be trademarks or
registered trademarks of the manufacturers or vendors of the
respective products.
Manufacturer:
Interlogix
2955 Red Hill Avenue, Costa Mesa, CA 92626-5923, USA
Authorized EU manufacturing representative:
UTC Fire & Security B.V.
Kelvinstraat 7, 6003 DH Weert, The Netherlands
Certification:
N4131
FCC compliance: Class A
Class A: This equipment has been tested and found to comply
with the limits for a Class A digital device, pursuant to part 15 of
the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instruction manual, may cause
harmful interference to radio communications. Operation of this
equipment in a residential area is likely to cause harmful
Installation Guide
7
interference in which case the user will be required to correct the
interference at his own expense.
ACMA compliance
Notice! This is a Class A product. In a domestic environment this
product may cause radio interference in which case the user may
be required to take adequate measures.
Canada
This Class A digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe A est conforme à la norme
NMB-0330 du Canada.
European Union directives:
12004/108/CE (EMC directive): Hereby, UTC Fire & Security declares
that this device is in compliance with the essential requirements and
other relevant provisions of Directive 2004/108/EC.
2002/96/CE (WEEE directive): Products marked
with this symbol cannot be disposed of as
unsorted municipal waste in the European Union.
For proper recycling, return this product to your
local supplier upon the purchase of equivalent
new equipment, or dispose of it at designated
collection points. For more information see:
www.recyclethis.info.
Contact information:
For contact information, see www.interlogix.com or
www.utcfssecurityproducts.eu..
8
Installation Guide