Installation Instructions Over the Range Microwave Oven

Installation Instructions Over the Range Microwave Oven
Installation
Instructions
BEFORE YOU BEGIN
•
•
Over the Range
Microwave Oven
Read these instructions completely and carefully.
IMPORTANT – Save these instructions for
local inspector's use.
•
•
IMPORTANT – Observe all governing codes
•
and coordinates.
•
Note to Installer – Be sure to leave these
•
instructions with the Consumer.
•
Note to Consumer – Keep these instructions for future reference.
•
Proper installation is the responsibility of the installer.
Product failure due to improper installation is not covered under the Warranty.
Please read all instructions thoroughly before installing
the Over the Range Microwave Oven. Two people are
recommended to install this product.
If a new electrical outlet is required, its installation
should be completed by a qualified electrician before
the Microwave Oven is installed. See 3 ELECTRICAL
GROUNDING INSTRUCTIONS on page 2.
Skill Level – Installation of this appliance
requires basic mechanical and electrical skills.
UNPACKING AND EXAMINING
YOUR OVEN
Open the bottom of the carton, bend the carton flaps back and
tilt the oven over to rest on plastic foam pad. Lift carton off oven
and remove all packing materials, WALL and TOP CABINET
TEMPLATE, Turntable, and Turntable Support. SAVE THE
CARTON AS IT MAY MAKE INSTALLATION EASIER.
1. Remove the feature sticker from the outside of the door, if
there is one.
Oven Cavity
Hinges
Door seals and
Safety door
sealing surfaces
latches
2. DO NOT REMOVE THE WAVEGUIDE COVER, which is
located on the right side wall of the oven cavity. Check to
see that there is a Wall TEMPLATE and Top CABINET
Template. Read enclosures and SAVE the Operation
Manual.
Check the oven for any damage, such as misaligned or bent
door, damaged door seals and sealing surfaces, broken or
loose door hinges and latches and dents inside the cavity or on
the door. If there is any damage, do not operate the oven and
contact your dealer or ELECTROLUX AUTHORIZED SERVICER. See Installation Instructions for more details.
NEED HELP?
For customers in the United States, call: 1-800-944-9044
For customers in Canada, call: 1-800-213-9397 (English)
1-800-668-4606 ext.8199 (French)
READ CAREFULLY. KEEP THESE INSTRUCTIONS.
1
P/N 316137336
TINSEB386MRR0
Installation Instructions
1 MOUNTING SPACE
3 ELECTRICAL GROUNDING
INSTRUCTIONS
This Microwave Oven/Hood requires a mounting space on a
wall as shown in Figure 1. It is designed to be used with standard 12-inch wall cabinets.
This appliance must be grounded. This oven is equipped with a
cord having a grounding wire with a grounding plug. It must be
plugged into a wall receptacle that is properly installed and
grounded in accordance with the National Electrical Code and
local codes and ordinances. In the event of an electrical short
circuit, grounding reduces risk of electric shock by providing an
escape wire for the electric current.
If the space between the wall cabinets is 36 or 42 inches, a
Filler Panel Kit can be used to fill the gap. The metal filler panels come in 3-inch wide pairs. One set is needed for a 36-inch
opening and 2 sets for a 42-inch opening. See page 15 for
ordering information. The Filler Panel Kit should be installed
before the Microwave Oven/Hood is installed.
WARNING - Improper use of the grounding plug can result in a
risk of electric shock.
ELECTRICAL REQUIREMENTS
The oven is equipped with a 3-prong
grounding plug. DO NOT UNDER
ANY CIRCUMSTANCES CUT OR
REMOVE THE GROUNDING PIN
FROM THE PLUG.
12"
30"
15.5"
Backsplash At least 2"
30" or more from
cooking surface
The Power Supply Cord and plug must be connected to a separate 120 Volt AC, 60 Hz, 15 Amp, or more branch circuit, single grounded receptacle. The receptacle should be located
inside the cabinet directly above the Microwave Oven mounting
location as shown in Figure 2.
66" or more
from floor
NOTE:
1.If you have any questions about the grounding or electrical
instructions, consult a qualified electrician or serviceperson.
2.Neither Electrolux nor the dealer can accept any liability for
damage to the oven or personal injury resulting from failure to
observe the correct electrical connection procedures.
Figure 1
RADIO OR TV INTERFERENCE
Should there be any interference caused by the microwave
oven to your radio or TV, check that the microwave oven is on
a different electrical circuit, relocate the radio or TV as far away
from the oven as feasible or check position and signal of receiving antenna.
2 WALL CONSTRUCTION
This Microwave Oven/Hood should be mounted against and
supported by a flat vertical wall. The wall must be flat for proper installation. If the wall is not flat, use spacers to fill in the
gaps. Wall construction should be a minimum of 2” x 4” wood
studding and 3/8” or more thick dry wall or plaster/lath. The
mounting surfaces must be capable of supporting a weight of
110 pounds—the oven and contents—AND the weight of all
items which would normally be stored in the top cabinet above
the unit.
Ground
Receptacle
The unit should be attached to a minimum of one 2” x 4”
wall stud or two 2" x 3" wall studs.
To find the location of the studs, one of the following methods
may be used:
Opening for
Power Cord
A.Use a stud finder, a magnetic device which locates the nails
in the stud.
Figure 2
B.Use a hammer to tap lightly across the mounting surface to
find a solid sound. This will indicate stud location.
The center of the stud can be located by probing the wall with a
small nail to find the edges of the stud and then placing a mark
halfway between the edges. The center of any adjacent studs
will normally be 16” or 24” to either side of this mark.
2
Installation Instructions
4 HOOD EXHAUST DUCT
5 TOOLS RECOMMENDED FOR
INSTALLATION
When the hood is vented to the outside, a hood exhaust duct is
required. All ductwork must be metal; absolutely do not use
plastic duct. Check that all connections are made securely.
Please read the following carefully:
Exhaust connection: The hood exhaust has been designed to
connect to a standard 3-1/4” X 10” rectangular duct. If round
duct is required, a rectangular-to-round adapter must be used.
Rear exhaust: If a rear or horizontal exhaust is to be used, care
should be taken to align the exhaust with the space between the
studs, or wall should be prepared at the time it is constructed by
leaving enough space between wall studs to accommodate
exhaust.
•
Phillips Screwdriver
•
Electric Drill
•
1/2”, 5/8” and 3/32” Drill
Bits
•
1-1/2” Wood Bit or Metal
Hole Cutter
(if metal cabinet is used)
•
Maximum duct length: For satisfactory air movement, the total
duct length of 3-1/4” X 10” rectangular or 6” diameter round duct
should not exceed 140 feet.
Saw to cut exhaust
opening (if needed)
•
Protective Drop Cloth for
product and range you may also use carton
for protection
•
Scissors
•
Pencil
•
Measure
•
Tape
6 INSTALLATION HARDWARE
Elbows, adapters, wall caps, roof caps, etc. present additional
resistance to air flow and are equivalent to a section of straight
duct which is longer than their actual physical size. When calculating the total length, add the equivalent lengths of all transitions and adapters plus the length of all straight duct sections.
Figure 3 shows the approximate feet of equivalent length of
some typical ductwork parts. Use the values in parentheses for
calculating air flow resistance equivalent, which should total
less than 140 feet.
The INSTALLATION HARDWARE items (1 - 7) are packed
in a small bag. Items 8- " are packed separately. All items
are in a small carton packed below the oven.
Item Name
Figure 3
Quantity
Part Code
1 Wood Screw 5 X 30 mm
6
XTSSD50P35000
2 Toggle Bolt with nuts
#10 - 24 X 50 mm
4
LX-BZ0195WRE0
3 Top Cabinet Screw 5 X 60 mm
2
XBRSD50P60000
4 Power Cord Hanger
1
LX-MZB001MRE0
5 Tapping Screw 4 x 12 mm
3
XOTSD40P12000
6 Flat Washer 30 mm diameter
2
XWHSD50-16300
7 Grommet
1
LBSHC0040MRE0
8 Rear Cushion
1
PCUSUB059MRP0
9 Exhaust Damper Assembly
1
FFTA-B005MRK0
! Scale Plate
2
LANG-B002MRP0
" Grease Filter
2
PFIL-B002MRE0
Figure 4
Parts shown not to common scale.
3
Installation Instructions
7 PREPARATION OF THE OVEN
1. Turn oven on the side. See Figure 5.
(A)
2. Follow steps (A)-(D) to remove mounting plate from the back
of the oven as shown in Figure 5.
(A)
Release mounting plate by pulling out the lever that is
on the bottom of the oven. See Figure 6.
(B)
When lever is out, pull that side of the mounting plate
away from the oven. See Figure 5.
(C)
Repeat step (A) on other side.
(D)
Repeat step (B) on other side.
(B)
(D)
(C)
8 VENTILATION SYSTEM
Figure 5
(PREPARING OVEN FOR INSTALLATION)
(A)
This Microwave Oven/Hood is designed for adaptation to three
types of hood ventilation systems. Select the type required for
your installation.
Mounting
Plate
Use screwdriver to
assist in releasing
mounting plate.
Recirculating — non-vented, ductless. Follow installation
procedure (A). Recirculating requires the use of the
Charcoal Filter, which has been installed in the oven.
Bottom of
Microwave
Horizontal Exhaust — outside ventilation.
Follow installation procedure (B).
Figure 6
Vertical Exhaust — outside ventilation.
Follow installation procedure (C).
(A) RECIRCULATING: Non-Vented, Ductless Operation
1. The unit is shipped assembled for recirculating.
2. The Exhaust Damper Assembly 9 is not required for recirculating exhaust.
3. Charcoal Filter, RK-260, is also sold as an accessory. See
back page for ordering information.
(B) HORIZONTAL EXHAUST: OUTSIDE VENTILATION
1. Remove 2 screws from back edge and 3 screws from the top
center of Fan Cover Bracket. Save 2 screws to be used later
and discard remaining 3. Remove Fan Cover Bracket by
sliding it in the opposite direction of the arrow on the Fan
Cover Bracket, as shown in Figure 7.
Figure 7
Figure 8
(A) Rotate 180˚
Save fan cover bracket
for future instructions.
2. Lift Hood Fan Unit carefully and slip wires out of cavity. See
Figure 8.
CAUTION: Do not pull or stretch hood fan wiring.
3. Rotate the Hood Fan Unit 180˚ so that the fan blade openings are facing the back of the oven. See Figure 9 (A).
Replace Hood Fan Unit into the oven. Be careful not to pinch
the wire and the Hood Fan Unit. See Figure 9 (B).
(B)
4. Put the wire back into the cavity. See Figure 10.
Figure 9
4
Figure 10
Installation Instructions
8 VENTILATION SYSTEM
(PREPARING OVEN FOR INSTALLATION) cont.
(C) VERTICAL EXHAUST: OUTSIDE VENTILATION
1. Remove and save 2 screws from back edge and 3 screws
from the top center of the Fan Cover Bracket. Remove Fan
Cover Bracket by sliding it in the opposite direction of the
arrow on the Fan Cover Bracket as shown in Figure 11.
2. Lift Hood Fan Unit carefully and slip wires out of cavity. See
Figure 12. Caution: Do not pull or stretch hood fan wiring.
3. Rotate the Hood Fan Unit 90˚ so that the fan blade openings
are facing the top of the oven. See Figure 13 (A). Replace
Hood Fan Unit into the oven. Be careful not to pinch the lead
wire between the inner bracket and the Hood Fan Unit. Put
the lead wire into Wire Box. See Figure 13 (B).
Figure 11
4. Replace the Fan Cover Bracket by sliding it into the slits in
the same direction as the arrow on the Fan Cover Bracket.
Make sure the fan blades are visible through the top openings in the oven before proceeding.
Figure 12
(B)
(A) Rotate 180˚
5. Attach the Fan Cover Bracket to unit with the 2 screws from
back edge and 3 screws from the top center of the Fan
Cover Bracket, which were removed in Step 1 above. See
Figure 14. The Hood Fan Unit is now rotated for vertical
exhaust operation.
6. Attach the Exhaust Damper Assembly 9 to the fan cover on
the top of the outercase cabinet by sliding it into the slits in
the same direction as the arrow. Use 1 Tapping Screw 4 X12
mm 5 from the INSTALLATION HARDWARE and tighten
into place. See Figure 15.
Figure 14
Figure 13
Exhaust Damper Assembly
9 OVEN INSTALLATION
THIS OVEN CANNOT BE PROPERLY INSTALLED WITHOUT
REFERRING TO THE MOUNTING INSTRUCTIONS FOUND
ON WALL AND TOP CABINET TEMPLATES.
THE NEXT STEP IS TO READ AND FOLLOW MOUNTING
INFORMATION ON WALL AND TOP CABINET TEMPLATES.
THIS OVEN MUST BE ATTACHED TO AT LEAST ONE WALL
STUD. SEE WALL CONSTRUCTION ON PAGE 6.
Figure 15
WHEN DONE WITH TEMPLATES, PROCEED TO MOUNTING
SCALE PLATE SECTION.
MOUNTING SCALE PLATE
Attach 2 Scale Plates ! with tape (not included). See Figure 16
and WALL TEMPLATE for locations.
Scale Plates
Mounting Plate
Figure 16
5
Installation Instructions
9 OVEN INSTALLATION cont.
MOUNTING PLATE
Toggle Bolt
1. Separate 4 Toggle Bolts 2, packed in the INSTALLATION
HARDWARE, from the Toggle Nuts.
2. Match 5/8” holes (not in studs), drilled through WALL TEMPLATE into wall to corresponding holes on Mounting Plate.
3. Insert Toggle Bolts into matched openings on Mounting
Plate. Put Toggle Nuts on Toggle Bolts. See Figure 17.
Mounting Plate
4. Position the Mounting Plate with the Toggle Bolts attached at
the wall location and insert Toggle Nuts and Bolts through
the holes in the wall with the Toggle Nuts closed. Figure 18.
Use Wood Screws 1 to attach the Mounting Plate to studs.
Figure 17
Space
more than
wall thickness
NOTE: Before insertion, be sure you leave a space more
than the thickness of the wall between the Mounting Plate
and the end of each of the Toggle Nuts (in the closed position). If you do not leave enough space, the Toggle Nut will
not be able to open on the other side of the wall. Also, once
a Toggle Nut opens, it cannot be withdrawn from the
hole; therefore make sure all of the Toggles are in the
correct position before insertion.
5. Align the Mounting Plate carefully and hold in position while
tightening Toggle Bolts. Pull Toggle Bolt toward you and turn
clockwise to tighten. Figure 19.
Wall
Figure 19
Figure 18
10 PREPARATION AND USE OF
THE CARTON TO ASSIST IN
THE INSTALLATION OF THE
MICROWAVE OVEN
Utilization of the carton may make installation easier.
1. Place carton upside down. See Figure 20.
2. Using cutting line around the carton, cut into two pieces (A)
and (B). See Figure 21.
3. Position oven to assist in mounting to the wall.
See Figure 22.
Top Side
Cutting Line
Figure 20
6
Installation Instructions
(A)
(B)
(B)
Figure 21
Figure 22
11 MOUNTING OVEN TO THE WALL
Two people are recommended to attach the Microwave
Oven/Hood to the Mounting Plate.
1. Thread the Power Supply Cord through the hole made in the
bottom of the top cabinet. Install the oven by snapping it onto
the Mounting Plate. See Figure 23.
2. Use two Tapping Screws 5 to secure the levers that are on
the bottom of the oven. See Figure 24.
3. Use two Top Cabinet Screws 3 and two Flat Washers 6,
supplied in the INSTALLATION HARDWARE, to attach the
unit to the top cabinet. See Figure 25.
5
5
4. Make a bundle of the Power Supply Cord and attach it to the
inside of the cabinet using the Power Cord Hanger 4. See
Figure 25.
Figure 23
Figure 24
4
3
6
Figure 25
7
Installation Instructions
OPTIONAL ACCESSORIES
CHECKLIST FOR INSTALLATION
Two optional accessories are available for this oven.
1. Charcoal Filter (RK-260). This is required when hood
exhaust is recirculated. If dealer does not stock this item, it
can be ordered by calling 1-800-642-2122.
1. Make sure the unit has been installed according to all of
the Installation Instructions and the Wall and Top Cabinet
Templates.
2. Filler Panel Kit. For use when the oven is installed in a 36inch or 42-inch wide opening. The metal filler panels come in
3-inch wide pairs. One set is needed for a 36-inch opening
and 2 sets for a 42-inch opening. White and black are available.
3. Keep the Installation Instructions.
2. Plug in the power cord.
To purchase contact:
Imperial Cal Products, Inc.
1141 S. Acacia Ave.
Fullerton, CA 92831
Phone: (714) 446-7440
Fax: (714) 446-7444
8
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement