datasheet for W16RA4G8M by Super Talent Technology Corporation

Add to my manuals
10 Pages

advertisement

datasheet for W16RA4G8M by Super Talent Technology Corporation | Manualzz
240-Pin DDR3- Reg/ECC-DIMM
DDR3 SDRAM
DDR3 Registered/ECC DIMM Module
4GB based on 4Gbit component
78FBGA with Pb-Free
Revision 1.0 (Nov. 2011)
-Initial Release
http://www.supertalent.com/oem
Products and Specifications discussed herein are subject to change without notice
1
© 2006 Super Talent Tech., Corporation.
240-Pin DDR3- Reg/ECC-DIMM
DDR3 SDRAM
1.0 Feature
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
JEDEC standard VDDQ=1.5V +/- 0.075V Power Supply
VDDQ = 1.5V ± 0.075V
Programmable CAS Latency: 6,7,8,9,10,11
Programmable Additive Latency(Posted CAS) : 0, CL - 2, or CL - 1 clock
Programmable CAS Write Latency(CWL) = 5(DDR3-800), 6(DDR3-1066), 7(DDR3-1333) and 8(DDR3-1600)
400MHz fCK for 800Mb/sec/pin, 533MHz fCK for 1066Mb/sec/pin, 667MHz fCK for 1333Mb/sec/pin, 800MHz fCK for
1600Mb/sec/pin
8-bit pre-fetch
Burst Length: 8 (Interleave without any limit, sequential with starting address “000” only), 4 with tCCD = 4 which does not allow
seamless read or write [either On the fly using A12 or MRS]
Internal(self) calibration : Internal self calibration through ZQ pin (RZQ : 240 ohm ± 1%)
Bi-directional Differential Data Strobe
Asynchronous Reset
On-Die termination using ODT pin
8 independent internal bank
Average Refresh Period 7.8us at lower than a TCASE 85°C, 3.9us at 85°C < TCASE < 95 °C
Serial presence detect with EEPROM
RDIMM Dimension (Nominal) 30.00 mm high, 133.35 mm wide
Based on JEDEC standard reference Raw Cards Lay out.
RoHS compliant
Gold plated contacts
2.0 Ordering Information
Part number
Density
W16RA4G8x
4GB
Module
Organization
512Mx72
Component
composition
512Mx8*9
Component
PKG
FBGA
Module
Rank
1
Description
PC3-12800
Note: Last Character x of the Part Number stand for DRAM vendor
S=Samsung; M=Micron; H=Hynix
3.0 Operating Frequencies
DDR3-1600
Unit
tCK
CL-tRCD-tRP
11-11-11
CAS Latency
tCK(min)
11
1.25
tRCD(min)
13.5
tRP(min)
13.5
tRAS(min)
35
ns
ns
tRC(min)
48.75
ns
4.0 Absolute Maximum DC Rating
Symbol
Vin , Vout
VDD
VDDQ
VDDL
TSTG
http://www.supertalent.com/oem
tCK
ns
ns
Parameter
Rating
Units
Voltage on any pin relative to VSS
Voltage on VDD & VDDQ supply relative to Vss
Short circuit current
Power dissipation
Storage Temperature
-0.4 ~ 1.975
-0.4 ~ 1.975
-0.4 ~ 1.975
-0.4 ~ 1.975
-55 ~ + 100
V
V
V
V
°C
Products and Specifications discussed herein are subject to change without notice
2
© 2006 Super Talent Tech., Corporation.
240-Pin DDR3- Reg/ECC-DIMM
DDR3 SDRAM
5.0 DIMM Pin Configurations (Front side/Back side)
Pin
Front
Pin
Back
Pin
Front
Pin
Back
Pin
Front
Pin
Back
Pin
Front
Pin
Back
1
VREFDQ
121
VSS
31
DQ25
151
VSS
61
A2
181
A1
91
DQ41
211
VSS
2
VSS
122
DQ4
32
VSS
152
DQS12
62
VDD
182
VDD
92
VSS
212
DQS14
3
DQ0
123
DQ5
33
DQS3
153
DQS12
63
NC
183
VDD
93
DQS5
213
DQS14
4
DQ1
124
VSS
34
DQS3
154
VSS
64
NC
184
CK0
94
DQS5
214
VSS
5
VSS
125
DQS9
35
VSS
155
DQ30
95
VSS
215
DQ46
6
DQS0
126
DQS9
36
DQ26
156
DQ31
65
VDD
185
CK0
DQ47
DQ42
216
DQ47
7
DQS0
127
VSS
37
DQ27
157
VSS
66
VDD
186
VDD
97
DQ43
217
VSS
8
VSS
128
DQ6
38
VSS
158
CB4
67
VREFCA
187
EVENT
98
VSS
218
DQ52
9
DQ2
129
DQ7
39
CB0
159
CB5
68
NC/Par_in
188
A0
99
DQ48
219
DQ53
10
DQ3
130
VSS
40
CB1
160
VSS
69
VDD
189
VDD
100
DQ49
220
VSS
11
VSS
131
DQ12
41
VSS
161
DQS17
70
A10/AP
190
BA1
101
VSS
221
DQS15
12
DQ8
132
DQ13
42
DQS8
162
DQS17
71
BA0
191
VDD
102
DQS6
222
DQS15
13
DQ9
133
VSS
43
DQS8
163
VSS
72
VDD
192
RAS
103
DQS6
223
VSS
14
VSS
134
DQS10
44
VSS
164
CB6
73
WE
193
S0
104
VSS
224
DQ54
15
DQS1
135
DQS10
45
CB2
165
CB7
74
CAS
194
VDD
105
DQ50
225
DQ55
16
DQS1
136
VSS
46
CB3
166
VSS
75
VDD
195
ODT0
106
DQ51
226
VSS
17
VSS
137
DQ14
47
VSS
167
NC
76
NC
196
A13
107
VSS
227
DQ60
18
DQ10
138
DQ15
48
VTT
168
RESET
77
NC
197
VDD
108
DQ56
228
DQ61
19
DQ11
139
VSS
49
VTT
169
NC
78
VDD
198
NC
109
DQ57
229
VSS
20
VSS
140
DQ20
50
CKE0
170
VDD
79
NC
199
VSS
110
VSS
230
DQS16
21
DQ16
141
DQ21
51
VDD
171
A15
80
VSS
200
DQ36
111
DQS7
231
DQS16
22
DQ17
142
VSS
52
BA2
172
A14
81
DQ32
201
DQ37
112
DQS7
232
VSS
23
VSS
143
DQS11
53
ERR_OUT
173
VDD
82
DQ33
202
VSS
113
VSS
233
DQ62
24
DQS2
144
DQS11
54
VDD
174
A12
83
VSS
203
DQS13
114
DQ58
234
DQ63
25
DQS2
145
VSS
55
A11
175
A9
84
DQS4
204
DQS13
115
DQ59
235
VSS
26
VSS
146
DQ22
56
A7
176
VDD
85
DQS4
205
VSS
116
VSS
236
VDDSPD
27
DQ18
147
DQ23
57
VDD
177
A8
86
VSS
206
DQ38
117
SA0
237
SA1
28
DQ19
148
VSS
58
A5
178
A6
87
DQ34
207
DQ39
118
SCL
238
SDA
29
VSS
149
DQ28
59
A4
179
VDD
88
DQ35
208
VSS
119
SA2
239
VSS
30
DQ24
150
DQ29
60
VDD
180
A3
89
VSS
209
DQ44
120
VTT
240
VTT
90
DQ40
210
DQ45
http://www.supertalent.com/oem
KEY
Products and Specifications discussed herein are subject to change without notice
3
© 2006 Super Talent Tech., Corporation.
240-Pin DDR3- Reg/ECC-DIMM
DDR3 SDRAM
6.0 DIMM Pin Description
Pin Name
Function
Pin Name
Function
A0 ~ A15
Address input (Multiplexed)
ODT0~ODT1
On Die Termination
A10/AP
Address Input/Auto pre-charge
CB0~CB7
ECC Data check bits Input/Output
BA0 ~ BA2
Bank Select
DQ0~DQ63
Data Input/Output
CK0 ~ CK2,
CK0~CK2
Clock input
DQS0~DQS8
Data strobes, negative line
CKE0, CKE1
Clock enable input
DM (0~8),
Data Masks/Data strobes (Read)
S0, S1
Chip select input
DQS0~DQS8
Data Strobes
RAS
Row address strobe
RFU
Reserved for future used
CAS
Column address strobe
VTT
SDRAM I/O termination power supply
WE
Write Enable
TEST
Memory bus test tool
SCL
SPD Clock Input
VDD
Core Power
SDA
SPD Data Input/Output
VDDQ
I/O Power
SA0~SA2
SPD Address
VSS
Ground
Par_In
Parity bit for address & Control bus
VREFDQ
SDRAM Input/Output Reference Supply
event
VDDSPD
Serial EEPROM Power Supply
Register and PLL control pin
VREFCA
Command Address Reference Supply
EVENT
Reset
EVENT pin on TS/SPD part, Temperature
7.0 Address Configuration
Organization
Row Address
Column Address
Bank Address
Auto Pre-charge
512Mx8(4Gb)base
A0-A15
A0-A9
BA0-BA2
A10
http://www.supertalent.com/oem
Products and Specifications discussed herein are subject to change without notice
4
© 2006 Super Talent Tech., Corporation.
240-Pin DDR3- Reg/ECC-DIMM
DDR3 SDRAM
8.0 Functional Block Diagram: 4GB; 512Mx72 Module (Populated as 1 rank of x8 SDRAM Module)
http://www.supertalent.com/oem
Products and Specifications discussed herein are subject to change without notice
5
© 2006 Super Talent Tech., Corporation.
240-Pin DDR3- Reg/ECC-DIMM
9.0
DDR3 SDRAM
AC & DC Operating Conditions
Recommended operating conditions (Voltage referenced to Vss=0V, TA=0 to 70°C)
Symbol
Parameter
Min
Typ
Max
Unit
VDD
VDDQ
VREFDQ(DC)
VREFCA(DC)
VTT
Supply Voltage
Supply Voltage for Output
I/O Reference Voltage (DQ)
I/O Reference Voltage (CMD/Add)
Termination Voltage
1.425
1.425
0.49*VDDQ
0.49*VDDQ
0.49*VDDQ
1.5
1.5
0.50*VDDQ
0.50*VDDQ
0.50*VDDQ
1.575
1.575
0.51*VDDQ
0.51*VDDQ
0.51*VDDQ
V
V
V
V
V
10.0 Capacitance (Max.)
Symbol
Parameter/Condition
Min
-
Input capacitance, CK and CK
CCK
CI1
-
Input capacitance, CKE and CS
-
Input capacitance, Addr, RAS, CAS, WE
CI2
CIO
-
Input capacitance, DQ, DM, DQS, DQS
Max
Unit
11
pF
12
pF
12
pF
10
pF
11.1 AC Timing Parameters & Specifications
(AC operating conditions unless otherwise noted)
Parameter
Symbol
Minimum Clock Cycle Time (DLL off mode)
tCK(DLL_OFF)
Average Clock Period
tCK(avg)
Clock Period
tCK(abs)
Average high pulse width
DDR3-1600
min
max
8
-
tCK(avg) min +tJIT
Units
ns
ps
(per)min
tCK(avg) max +tJIT
(per)max
ps
tCH(avg)
0.47
0.53
tCK(avg)
Average low pulse width
tCL(avg)
0.47
0.53
tCK(avg)
Clock Period Jitter
tJIT(per)
-70
70
ps
Clock Period Jitter during DLL locking period
tJIT(per, lck)
-60
60
ps
Cycle to Cycle Period Jitter
tJIT(cc)
140
-
ps
Cycle to Cycle Period Jitter during DLL locking period
tJIT(cc, lck)
120
-
ps
Cumulative error across 2 cycles
tERR(2per)
- 103
103
ps
Cumulative error across 3 cycles
tERR(3per)
- 122
122
ps
Cumulative error across 4 cycles
tERR(4per)
- 136
136
ps
Cumulative error across 5 cycles
tERR(5per)
- 147
147
ps
Cumulative error across 6 cycles
tERR(6per)
- 155
155
ps
Cumulative error across 7 cycles
tERR(7per)
- 163
163
ps
Cumulative error across 8 cycles
tERR(8per)
- 169
169
ps
Cumulative error across 9 cycles
tERR(9per)
- 175
175
ps
Cumulative error across 10 cycles
tERR(10per)
- 180
180
ps
http://www.supertalent.com/oem
Products and Specifications discussed herein are subject to change without notice
6
© 2006 Super Talent Tech., Corporation.
240-Pin DDR3- Reg/ECC-DIMM
DDR3 SDRAM
11.2 AC Timing Parameters & Specifications (con’t)
Parameter
Symbol
Cumulative error across 11 cycles
tERR(11per)
Cumulative error across 12 cycles
tERR(12per)
DDR3-1600
Units
min
max
- 184
184
ps
- 188
188
ps
tERR(nper)min = (1 + 0.68ln(n))*tJIT(per)min
tERR(nper)max = (1 = 0.68ln(n))*tJIT(per)max
Cumulative error across n = 13, 14 ... 49, 50 cycles
tERR(nper)
Absolute clock HIGH pulse width
tCH(abs)
0.43
-
tCK(avg)
Absolute clock Low pulse width
tCL(abs)
0.43
-
tCK(avg)
DQS, /DQS to DQ skew, per group, per access
tDQSQ
-
100
ps
DQ output hold time from DQS, /DQS
tQH
0.38
-
tCK(avg)
DQ low-impedance time from CK, /CK
tLZ(DQ)
-450
225
ps
DQ high-impedance time from CK, /CK
tHZ(DQ)
-
225
ps
TBD
-
ps
10
-
ps
ps
Data Timing
tDS(base)
AC175
tDS(base)
AC150
tDH(base)
DC100
Data setup time to DQS, /DQS referenced to Vih(ac)Vil(ac) levels
Data hold time to DQS, /DQS referenced to Vih(ac)Vil(ac) levels
DQ and DM Input pulse width for each input
45
-
ps
tDIPW
360
-
ps
tRPRE
0.9
-
tCK
Data Strobe Timing
DQS, /DQS READ Preamble
DQS, /DQS differential READ Postamble
tRPST
0.3
-
tCK
DQS, /DQS output high time
tQSH
0.4
-
tCK(avg)
DQS, /DQS output low time
tQSL
0.4
-
tCK(avg)
DQS, /DQS WRITE Preamble
tWPRE
0.9
-
tCK
DQS, /DQS WRITE Postamble
tWPST
0.3
-
tCK
DQS, /DQS rising edge output access time from rising CK, /CK
tDQSCK
-225
225
ps
DQS, /DQS low-impedance time (Referenced from RL-1)
tLZ(DQS)
-450
225
ps
DQS, /DQS high-impedance time (Referenced from RL+BL/2)
tHZ(DQS)
-
225
ps
DQS, DQS differential input low pulse width
tDQSL
0.45
0.55
tCK
DQS, DQS differential input high pulse width
tDQSH
0.45
0.55
tCK
DQS, DQS rising edge to CK, /CK rising edge
tDQSS
-0.27
0.27
tCK(avg)
DQS,DQS faling edge setup time to CK, /CK rising edge
tDSS
0.18
-
tCK(avg)
DQS,DQS faling edge hold time to CK, /CK rising edge
tDSH
0.18
-
tCK(avg)
DLL locking time
tDLLK
512
-
nCK
internal READ Command to PRECHARGE Command delay
tRTP
Delay from start of internal write transaction to internal read command
tWTR
WRITE recovery time
tWR
Mode Register Set command cycle time
max
(4tCK,7.5ns)
max
(4tCK,7.5ns)
-
15
-
ns
tMRD
4
-
nCK
Mode Register Set command update delay
tMOD
max
(12tCK,15ns)
-
CAS# to CAS# command delay
tCCD
4
-
Auto precharge write recovery + precharge time
tDAL(min)
http://www.supertalent.com/oem
WR + roundup (tRP / tCK(AVG))
nCK
nCK
Products and Specifications discussed herein are subject to change without notice
7
© 2006 Super Talent Tech., Corporation.
240-Pin DDR3- Reg/ECC-DIMM
DDR3 SDRAM
11.3 AC Timing Parameters & Specifications (con’t)
Parameter
Symbol
Multi-Purpose Register Recovery Time
tMPRR
DDR3-1600
Units
min
max
1
-
nCK
36
70,000
ns
ACTIVE to PRECHARGE command period
tRAS
ACTIVE to ACTIVE command period for 1KB page size
tRRD
ACTIVE to ACTIVE command period for 2KB page size
tRRD
Four activate window for 1KB page size
tFAW
30
-
ns
tFAW
40
-
ns
45
-
ps
45+125
-
ps
120
-
ps
tIPW
560
-
ps
Power-up and RESET calibration time
tZQinitI
512
-
tCK
Normal operation Full calibration time
tZQoper
256
-
tCK
Normal operation short calibration time
tZQCS
64
-
tCK
tXPR
max(5tCK, tRFC+
10ns)
-
Exit Self Refresh to commands not requiring a locked DLL
tXS
max(5tCK,tRFC+
10ns)
-
Exit Self Refresh to commands requiring a locked DLL
tXSDLL
tDLLK(min)
-
Four activate window for 2KB page size
Command and Address setup time to CK, /CK referenced to Vih(ac) / Vil(ac) levels
Command and Address hold time from CK, /CK referenced to Vih(ac) / Vil(ac) levels
Control & Address Input pulse width for each input
tIS(base)
AC175
tIS(base)
AC150
tIH(base)
DC100
max
(4tCK,6ns)
max
(4tCK,7.5ns)
-
Calibration Timing
Reset Timing
Exit Reset from CKE HIGH to a valid command
Self Refresh Timing
Minimum CKE low width for Self refresh entry to exit timing
tCKESR
Valid Clock Requirement after Self Refresh Entry (SRE)
tCKSRE
Valid Clock Requirement before Self Refresh Exit (SRX)
tCKSRX
tCKE(min) +
1tCK
max(5tCK,
10ns)
max(5tCK,
10ns)
nCK
-
Power Down Timing
Exit Power Down with DLL on to any valid command; Exit Precharge Power Down with
DLL frozen to commands not requiring a locked DLL
tXP
Exit Precharge Power Down with DLL frozen to commands requiring a locked DLL
tXPDLL
CKE minimum pulse width
tCKE
Command pass disable delay
tCPDED
Power Down Entry to Exit Timing
tPD
Timing of ACT command to Power Down entry
tACTPDEN
Timing of PRE command to Power Down entry
tPRPDEN
Timing of RD/RDA command to Power Down entry
tRDPDEN
Timing of WR command to Power Down entry (BL8OTF, BL8MRS, BL4OTF)
tWRPDEN
WL + 4 +(tWR/tCK)
-
nCK
Timing of WRA command to Power Down entry (BL8OTF, BL8MRS, BL4OTF)
tWRAPDEN
WL + 4 +WR+1
-
nCK
tWRPDEN
WL + 2 +(tWR/
tCK(avg))
-
nCK
Timing of WR command to Power Down entry (BL4MRS)
http://www.supertalent.com/oem
max
(3tCK,6ns)
-
max(10tCK, 24ns)
-
max(3tCK, 5 ns)
-
1
-
nCK
tCKE(min)
9*tREFI
tCK
1
-
nCK
1
-
nCK
RL + 4 +1
-
Products and Specifications discussed herein are subject to change without notice
8
© 2006 Super Talent Tech., Corporation.
240-Pin DDR3- Reg/ECC-DIMM
DDR3 SDRAM
11.4 AC Timing Parameters & Specifications (con’t)
Parameter
Symbol
Timing of WRA command to Power Down entry(BL4MRS)
DDR3-1600
min
max
tWRAPDEN
WL +2 +WR +1
-
Timing of REF command to Power Down entry
tREFPDEN
1
-
Timing of MRS command to Power Down entry
tMRSPDEN
tMOD(min)
-
Units
nCK
ODT Timing
ODT high time without write command or with wirte commandand BC4
ODTH4
4
-
nCK
ODT high time with Write command and BL8
ODTH8
6
-
nCK
Asynchronous RTT tum-on delay (Power-Down with DLL frozen)
tAONPD
2
8.5
ns
Asynchronous RTT tum-off delay (Power-Down with DLL frozen)
tAOFPD
2
8.5
ns
ODT turn-on
tAON
-225
225
ps
RTT_NOM and RTT_WR turn-off time from ODTL off reference
tAOF
0.3
0.7
tCK(avg)
RTT dynamic change skew
tADC
0.3
0.7
tCK(avg)
First DQS pulse rising edge after tDQSS margining mode is programmed
tWLMRD
40
-
tCK
DQS/DQS delay after tDQS margining mode is programmed
tWLDQSEN
25
-
tCK
Setup time for tDQSS latch
tWLS
165
-
ps
Hold time of tDQSS latch
tWLH
165
-
ps
Write Leveling Timing
Write leveling output delay
tWLO
0
7.5
ns
Write leveling output error
tWLOE
0
2
ns
http://www.supertalent.com/oem
Products and Specifications discussed herein are subject to change without notice
9
© 2006 Super Talent Tech., Corporation.
240-Pin DDR3- Reg/ECC-DIMM
DDR3 SDRAM
12.0 Physical Dimensions: (512Mx8 Based)
512Mx72 (1 Rank)
Tolerances: ± 0.005(.13) unless otherwise specified
http://www.supertalent.com/oem
Products and Specifications discussed herein are subject to change without notice
10
© 2006 Super Talent Tech., Corporation.

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement