HARMAN RNS-E FIS Bluetooth kit Installation Manual

The Bluetooth kit RNS-E FIS is a device that allows you to connect your phone to your car's radio system. This allows you to make and receive calls, listen to music, and access other features of your phone through your car's radio. The kit is designed for Audi vehicles with the RNS-E navigation system and FIS (multi-function display). The installation process involves connecting the kit to your car's radio, coding the radio and Bluetooth unit, and then pairing your phone to the kit. The kit also includes a microphone that can be placed in a variety of locations in your car.

PDF

Document

A ET (Y ducce MS
NN
TA coord LE wm нк
Installation Manual Bluetooth
Original Audi RNS-E / FIS
Note: This Plug &amp; Play wiring harness is manufactured specially for cars with CAN-BUS Gateway (A3, TT). If you
have an A3, or TT, you don t have to change nothing.
For Audi A4 B6 or B7, Audi A6 4B. The diagnosis communication goes through K-Line. Only, if your car have cd-
changer factory installed and Quadlock connector, omit this step. Because you already have the K-Line on the blue
connector behind the radio.
If your vehicle doesn’t have Cd changer with Quadlock connector, you must perform the following steps:
1 - You must connect from a K-Line source to the below terminals red colored.
2 - Fo example: From the diagnosis (OBD) Terminal 7 or Climatronic, “D-connector” T16 Terminal 7.
RNS-E SIMPHONY 2+
1] 5] 913] 1] 5] of 13]
1 0 0 1 1 0 01
1 0 0 1 || 1 0 0 1
I, el 120160 L-10A- | |
al el 12116 | -10A- |=
K-Line ll K-Line
be: 6 || 1 E 1 6 &gt;
00090680 90909060 000060 a a
09000000 поооооо ооо о вооооро
7 12,7 12 7 12,7 1
E 1 || 4
The installation of the Bluetooth kit consists of the following steps:
STEP 1:
Remove the original vehicle's Radio or Navigation system using a removal tool.
STEP 2:
Locate the BT interface in a place where it can be fixed and subject, for example behind the auto glove compartment,
steering wheel's side, with flanges or any tooling and protect it with a foam if you want to protect it better from vibrations.
STEP 3:
Connect the terminals of the Plug &amp; Play wiring harness to their respective units.
+ 54-pin connector (black elongated, with a white holding tab) connected to the bluetooth interface box.
* Female Connector Quadlock -&gt; Original Quadlock connector of the vehicle.
* Male Connector Quadlock -&gt; Radio/Navigation System.
* Locate the microphone in the overhead dome light panel or where you prefer.
If you have an Audi's Plug &amp; Play wiring harness with ISO connection factory installed. (if not, omit this step)
* 54-pin connector (black elongated, with a white holding tab) connected to the bluetooth interface box.
+ Female ISO Connectors -&gt; Original ISO Connectors of the vehicle.
* Male Connector Quadlock -&gt; 3d generation Radio/Navigation System RNS-E.
* Locate the original microphone in the overhead courtesy lights panel or where you prefer.
STEP 4:
Code the Radio/Navigation unit, the Bluetooth unit and MFD (only if you have them) by using VCDS/Vas 5051 or higher.
Depending on the Radio/Navigation System the coding will be different.
Concert II (1 Din)
Audi vehicles with Radio Concert Il {1 Din) enter to channel 56 and change the query by adding the necessary digit.
Oxxxx?x: Options
Telephone installed +2
Oxxxxx?: Options
Multifunction steering wheel installed +4
Concert II (2 Din)
Audi with Radio Concert II (2 Din) enter to channel 56 and change the query by adding the necessary digit.
07x0xxx: Options
Multifunction steering wheel +2
Phone +4
Navigation RNS-E System
In vehicles which have Audi Navigation RNS-E System enter to channel 37 and change the query by the necessary digit.
0xxx?xx: Phone
7 = Telephone Control through diagnosis
Once we have coded the Radio/Navigation System unit, we must code the Bluetooth unit.
Enter to Channel 77 Telephone, 07 “recode” function
00?xxxx: Features
0 = Basic (for Radio)
1 = Comfort (for RNS-E)
00x ?xxx: Multifunction Steering wheel
0 = No Multifunction
1 = Multifunction Steering wheel
00xx xx: Installation
1 = Diagnosis via CAN
2 = Multifunction steering wheel, Diagnosis via CAN
3 = With RNSE, Diagnosis via CAN
4 = With Multifunction steering wheel, with ANSE, Diagnosis via CAN
5 = Diagnosis via K-Line
6 = With Multifunction steering wheel, Diagnosis via K-Line
7 = RNS-E, Diagnosis via K-Line
8 = With Multifunction steering wheel, with RNSE, Diagnosis via K-Line
ООххх?х: Language (Voice Control)
0 = OFF Voice Control by or through the RNSE (SDS)
1 = German
2 = English (UK)
3 = French
4 = Italian
5 = Spanish
6 = Czech
7 = English (U.S.)
&amp; = French (CA)
00xxx?: Language (FIS)
0= No FIS
1= German
2 = English (UK)
3 = French
4 = Italian
5 = Spanish
6 = Czech
7 = English (U.5.)
8 = French (CA)
Once we have coded the Radio/Navigation and Bluetooth units, we can proceed to code the steering wheel electro-
nics ECU, channel 16, where we will change the digit that is in the query's position.
For the Audi A3 (8P)
00x xx: Multifunction Steering Wheel
3 = Multifunction Steering Wheel with Radio / Telephone installed
4 = Multifunction Steering Wheel with Radio / Telephone installed / Voice control
For the Audi A4 (8E)
Dhoom: Multifunction Steering Wheel
3 = Multifunction Steering Wheel with Radio / Telephone installed
4 = Multifunction Steering Wheel with Radio / Telephone installed / Voice control
For the Audi A6 4B
Ooo ?: Multifunction Steeringwheel
1 = Radio and Telephone installed
5 = Radio / Telephone and Voice Control
Only with cars A4 ( BE } or A6 (4B )
Enter to Channel 17 Instruments Cluster, go to 10-Adaptation -&gt; channel 62.
Add +2 to the value
+00002 = Telephone (Optional)
Once all is correctly coded, now pair the phone and access code type in 1234,
">

Hello! I am an AI chatbot specifically trained to assist you with the Harman RNS-E FIS Installation manual. I have thoroughly reviewed the document and can help you locate the exact information you need or explain the content in clear and simple terms. Whether you’re looking for guidance on specific features, troubleshooting steps, or general usage, feel free to ask your questions. The more details you provide about your concerns or needs, the more accurately and effectively I can assist you!

Show related prompts

Assistant typing

Assistant is out of keyboard. Please, try again later.

Key features

Connects phone to car radio
Make and receive calls
Listen to music
Access phone features
Designed for Audi RNS-E and FIS
Includes microphone
Easy to install

Frequently asked questions

The kit will automatically search for your phone when you turn on the ignition. Once your phone is found, you will be prompted to enter a PIN code. The default PIN code is 1234. You can then select the phone from the list of available devices on your radio.

Yes, you can stream music from your phone to the car's radio using the Bluetooth kit.

The microphone can be placed in a variety of locations in your car, such as the overhead dome light panel or under the steering wheel.

You will need a VCDS/Vas 5051 or higher device to code the radio and Bluetooth unit. The coding process will vary depending on the model of your car.