Quick Installation Guide

TEW-455APBO

2.01

Table of Contents

English

1. Before You Start

2. Hardware Installation

3. Configure the Access Point

4. Configure for WDS Mode

5. Mounting

6. Connecting TRENDnet External Antenna

Troubleshooting

1

1

2

6

10

14

16

17

Version 11.19.2009

1. Before You Start

Package Contents

System Requirements

Note: The TEW-455APBO does not support IEEE 802.3af. You must use the special

Power over Ethernet injector that is supplied with the TEW-455APBO.

*Check package contents for waterproof kit: (Ethernet Cable is not included)

1

2. Hardware Installation

Connecting the Grounding Wire

1. Remove the screw and washer from the grounding hole using a screwdriver.

2. Align one end of the grounding wire over the hole. Then connect the screw and washer back in.

3. Connect the green grounding wire to a grounding object. e.g. Earth Driven rod,

Grounded Electrical System, Building Frame.

Connecting the Ethernet Cable

1. Unscrew the sealing nut from the main body.

2. Separate the rubber seal from the claw.

3. Verify that you have the following parts:

Cable Gland, Seal, Claw, Sealing Nut.

2

4. Insert one end of an Ethernet cable into the sealing nut .

5. Insert the Ethernet cable into the seal.

6. Insert the seal into the claw.

7. Insert the seal/rubber claw into the Cable

Gland.

8. Connect the Ethernet Cable to the PoE port on the rear of the TEW-455APBO.

9. Using your hand, screw the main body counter clockwise to secure it to the TEW-455APBO.

10. Using your hand, screw the seal nut counter clockwise to secure it to the main body.

Powering the TEW-455APBO

1. Connect one end of an Ethernet cable into the

TEW-455APBO (See Connecting the Ethernet

Cable).

2. Connect the opposite end of the Ethernet cable to the P+DATA OUT port on the Power over Ethernet Injector.

3. Connect one end of another Ethernet cable to the DATA IN port on the Power over Ethernet

Injector.

4

4. Connect the opposite end of the Ethernet cable to a LAN port on your network.

5. Connect the power cord into the Power over

Ethernet Injector. Then connect the power cord into a power outlet.

6. Verify that the following panel lights are on:

LAN, WLAN and PWR.

5

3. Configure the Access Point

Note:

1. It is recommended that you configure the Access Point from a wired computer.

Before the Access Point can be configured, a Static IP address must be assigned to your computer's network adapter in the subnet of 192.168.10.x. Since the Access

Point's default IP address is 192.168.10.100, make sure no other network devices are assigned an IP address of 192.168.10.100. (Refer to Troubleshooting section on how to configure TCP/IP settings on your PC.)

2. Disable any anti-virus and firewall programs before configuring the access point.

1. Open your web browser, type the IP address of Access Point in the Address bar, and then press Enter. The default IP address is

192.168.10.100.

2. Enter the User name and Password, and then click OK. By default:

User Name: root

Password: root

3. Click System -> LAN.

6

4. Configure the LAN settings to match your network settings and then click Save.

5. Click Wireless -> Virtual AP Setup.

6. Select Edit for the desired VAP.

7

Note:

1. To protect your network from any unauthorized access it is recommended to enable wireless encryption.

2. The examples below are for WPA2-PSK. If you select WPA-PSK or WPA2-PSK, make sure your wireless adapters support WPA or WPA2. If your wireless adapters do not support WPA or WPA2, then select WEP.

7. Enter the desired ESSID and click Enable for

Enable VAP.

8. Select the desired Security Type.

9. Select the Cipher Suite (Type). For WPA2-

PSK, select AES.

10. Enter a Pre-shared Key and then click Save.

For WPA-PSK or WPA2-PSK, the Pre-

Shared Key must be between 8 and 63 ASCII or 64 HEX characters. Make sure to copy down the encryption key.

11. Click Reboot.

8

12. Click Reboot.

13. Wait 80 seconds while the Access Point reboots.

Your Installation is complete

For detailed information regarding the TEW-455APBO configuration and advanced settings, please refer to the Troubleshooting section, User's Guide on the Utility CD-ROM, or

TRENDnet's website at http://www.trendnet.com.

Register Your Product

To ensure the highest level of customer service and support, please take a moment to register your product Online at:

www.trendnet.com/register

Thank you for choosing TRENDnet

9

4. Configure for WDS Mode

Note:

1. WDS Mode requires at least 2 TEW-455APBO

2. Please install and test in a lab environment before mounting the TEW-455APBO.

3. After you set the TEW-455APBO to WDS mode, wireless clients will not be able to connect to the TEW-455APBO.

108Mbps 14dBi High Power Wireless

Outdoor PoE Access Point

(TEW-455APBO)

19dBi Outdoor High Gain

Directional Antenna

(TEW-AO19D)

Internet

Cable/DSL

Modem

PoE Power Adapter

Cable/DSL Advanced

VPN Firewall Router

(TW100-BRV304)

PoE Power Adapter

16-Port 10/100Mbps

GREENnet Switch

(TE100-S16Eg)

Cable

(TEW-ASAL1)

10/100Mbps

Multi-Port Print Server

(TE100-P21)

Notebook with

PC Card

Workstations with

PCI Adapter

Printers

Ethernet

Workstations with

PCI Adapter

PoE

Setting Up the Main TEW-455APBO

1. Copy down the 12 digit Mac ID (Address) of the Remote TEW-455APBOs. The Mac ID is on the side of the TEW-455APBO

2. Follows steps 1-4 and 11-13 in section 3

Configure the Access Point.

3. Click System -> Operation Mode.

10

4. Select WDS Mode and then click Save &

Reboot.

5. Wait 80 seconds while the Access Point reboots.

6. Click Wireless -> WDS Setup.

7. Select Enable, select AES for security type and enter an AES Key.

8. Click Enable and enter the remote TEW-

455APBO's MAC address. Then click Save.

11

9. Click Reboot.

10. Click Reboot.

11. Wait 80 seconds while the Access Point reboots.

12. Connect the main TEW-455APBO to the router on your LAN.

Setting Up the Remote TEW-455APBO

1. Copy down the 12 digit Mac ID (Address) of the Main TEW-455APBOs. The Mac ID is on the side of the TEW-455APBO.

2. Follows steps 1-4 and 11-13 in section 3

Configure the Access Point. Make sure you change the IP address of the Remote TEW-

455APBO to be different from the main TEW-

455APBO.

3. Repeat steps 3-11 in Setting Up the Main

TEW-455APBO for the second

TEW-455APBO.

12

4. Connect the Remote TEW-455APBO to a switch (e.g. TE100-S16Eg) in the remote location.

5. Connect a computer to a switch (e.g. TE100-

S16Eg) in the remote location.

6. Make sure the top of TEW-455APBO is pointed directly at the remote TEW-455ABPO.

13

5. Mounting

Wall Mounting

1. Align the mounting bracket with the holes on the bottom of the unit and secure it with the screws and washers provided.

2. Use the wall bracket as a template and mark the wall for the correct screw / fastener position.

3. Drill holes for the fastener plugs at the marked positions on the wall.

4. Insert fastener plugs into the drilled holes.

5. Use the provided wood screws to screw the outdoor unit/swivel mounting bracket to the fastener plugs to the wall.

6. Insert the mounting bracket into the wall mounting bracket and secure with the washers and screws provided.

7. Adjust the orientation of the antenna as necessary.

8. Once the unit is positioned correctly, tighten all screws.

14

Pole Mounting

1. Align the mounting bracket with the holes on the bottom of the unit and secure it with the screws and washers provided.

2. Slide the two provided u-clamps around the pole. Place the pole mounting bracket at the desire height and position

3. Secure the mounting bracket to the pole mounting bracket using the nuts and washers provided.

4. Adjust the orientation of the antenna as necessary.

15

6. Connecting TRENDnet External Antenna

Note: Connecting a TRENDnet External Antenna to the TEW-455APBO requires the

TEW-ASAL1.

1. Remove the metal cap from the connector labeled EXT.

2. Screw one end of the TEW-ASAL1 to the EXT connector on the TEW-455APBO.

3. Connect the opposite end of the TEW-ASAL1 to an outdoor antenna.

4. Use weather-proof tape to wrap the connectors.

16

Troubleshooting

How do I configure TCP/IP settings on my computer?

Windows Vista

1. Go into the Control Panel, click Network and Internet, click Network and Sharing Center, click Manage

Network Connections and then right-click the Local

Area Connection icon and then click Properties.

2. Click Internet Protocol Version 4(TCP/IPv4) and then click Properties. Then click on Use the

following IP address, and make sure you assign your network adapter an IP address in the subnet of 192.168.10.x.

Windows XP/2000

1. Go into the Control Panel, double-click the Network

Connections icon and then right-click the Local Area

Connection icon and then click Properties.

2. Click Internet Protocol (TCP/IP) and then click

Properties. Then click on Use the following IP

address, and make sure you assign your network adapter an IP address in the subnet of

192.168.10.x.

I am using a non-Windows based computer. How do I configure IP Address and Wireless settings on the Access Point?

1. Assign your computer a static IP Adress of 192.168.10.x (where X is an available address from 1 to 254. Since the IP address of the TEW-455APBO is 192.168.10.100, do not assign your computer a static IP address of 192.168.10.100.

2. Follow all the steps in Section 3 Configure the Access Point to configure the IP and

Wireless settings on the Access Point.

I changed the password on the Access Point, but I can no longer login. What should I do?

Reset the unit using the following procedure.

1. Press on the reset button. The reset button is located next to the LEDs.

2. Wait 10 seconds, then let go of the reset button.

The default user name and password is root

17

I typed http://192.168.10.100 in my Internet Browser's Address Bar, but an error message says “The page cannot be displayed.” How can I get into the TEW-455APB0's Browser configuration page?

1. Check your hardware settings again by following the instructions in section 2.

2. Make sure the LAN, WLAN and PWR LEDs are lit.

3. Make sure the TCP/IP settings are configured properly.

4. Since the Access Point's default IP address is 192.168.10.100, make sure that no other network devices are assigned an IP address of 192.168.10.100.

5. The IP address may have changed. Reset the TEW-455APBO to return all settings to factory default. To reset the TEW-455APBO, see the above troubleshooting question.

If my network's IP is different than the Access Point's range, what should I do?

You should still configure the Access Point first. After all the settings are applied, go to the

Access Point's configuration page, click on IP settings and change the IP address of the

Access Point to match your network's IP.

After I successfully configured the Access Point to match my network settings, I can not connect to my network using wireless computers.

If you have a DHCP server in your network, you need to go into TCP/IP settings again and reselect "Obtain an IP address automatically" to allow the PC to regain an IP address from your

DHCP server.

All the settings are correct, but I can not make a wireless connection to the Access Point.

1. Double check that the WLAN light on the Access Point is lit.

2. Power cycle the Access Point. Disconnect the Ethernet cable that is connected to the

P+DATA OUT port. Wait 15 seconds, then plug the power back in.

3. Contact the manufacturer of your Wireless Network Adapter. Make sure the Wireless

Network Adapter is configured with the proper SSID. The default SSID of the Access Point is TRENDnet455APB00.

If you still encounter problems or have any questions regarding the TEW-455APBO, please contact

TRENDnet's Technical Support Department.

82

GPL/LGPL General Information

This TRENDnet product includes free software written by third party developers. These codes are subject to the GNU

General Public License ("GPL") or GNU Lesser General Public License ("LGPL"). These codes are distributed WITHOUT

WARRANTY and are subject to the copyrights of the developers. TRENDnet does not provide technical support for these codes. The details of the GNU GPL and LGPL are included in the product CD-ROM.

Please also go to (http://www.gnu.org/licenses/gpl.txt) or (http://www.gnu.org/licenses/lgpl.txt) for specific terms of each license.

The source codes are available for download from TRENDnet's web site (http://trendnet.com/downloads/list_gpl.asp) for at least three years from the product shipping date.

You could also request the source codes by contacting TRENDnet.

20675 Manhattan Place, Torrance, CA 90501, USA. Tel: +1-310-961-5500 Fax: +1-310-961-5511

Informations générales GPL/LGPL

Ce produit TRENDnet comprend un logiciel libre écrit par des programmeurs tiers. Ces codes sont sujet à la GNU General

Public License ("GPL" Licence publique générale GNU) ou à la GNU Lesser General Public License ("LGPL" Licence publique générale limitée GNU). Ces codes sont distribués SANS GARANTIE et sont sujets aux droits d'auteurs des programmeurs. TRENDnet ne fournit pas d'assistance technique pour ces codes. Les détails concernant les GPL et LGPL

GNU sont repris sur le CD-ROM du produit.

Veuillez également vous rendre en (http://www.gnu.org/licenses/gpl.txt) ou en (http://www.gnu.org/licenses/lgpl.txt) pour les conditions spécifiques de chaque licence.

Les codes source sont disponibles au téléchargement sur le site Internet de TRENDnet web site

(http://trendnet.com/downloads/list_gpl.asp) durant au moins 3 ans à partir de la date d'expédition du produit.

Vous pouvez également demander les codes source en contactant TRENDnet.

20675 Manhattan Place, Torrance, CA 90501, USA. Tel: +1-310-961-5500 Fax: +1-310-961-5511

Allgemeine Informationen zu GPL/LGPL

Dieses Produkt enthält die freie Software "netfilter/iptables" (© 2000-2004 netfilter project http://www.netfilter.org) und die freie Software „Linux „mtd“ (Memory Technology Devices) Implementation (© 2000 David Woodhouse), erstmals integriert in

Linux Version 2.4.0-test 3 v. 10.07.2000 (http://www.kernel.org/pub/linux/kernel/v2.4/old-test-kernels/linux-2.4.0-test3.tar.bz2), sowie weitere freie Software. Sie haben durch den Erwerb dieses Produktes keinerlei Gewährleistungsansprüche gegen die

Berechtigten an der oben genannten Software erworben; weil diese die Software kostenfrei lizenzieren gewähren sie keine

Haftung gemäß unten abgedruckten Lizenzbedingungen. Die Software darf von jedermann im Quell-und Objektcode unter

Beachtung der Lizenzbedingungen der GNU General Public License Version 2, und GNU Lesser General Public License

(LGPL) vervielfältigt, verbreitet und verarbeitet werden. Die Lizenz ist unten im englischsprachigen Originalwortlaut wiedergegeben. Eine nichtoffizielle Übersetzung in die deutsche Sprache finden Sie im Internet unter

(http://www.gnu.de/documents/gpl-2.0.de.html). Eine allgemeine öffentliche GNU Lizenz befindet sich auch auf der mitgelieferten CD-ROM.

Sie können Quell-und Objektcode der Software für mindestens drei Jahre auf unserer Homepage www.trendnet.com im

Downloadbereich (http://trendnet.com/langen/downloads/list_gpl.asp) downloadend. Sofern Sie nicht über die Möglichkeit des Downloads verfügen können Sie bei TRENDnet.

20675 Manhattan Place, Torrance, CA 90501 -U.S.A -, Tel.: +1-310-961-5500, Fax: +1-310-961-5511 die Software anfordern.

Información general sobre la GPL/LGPL

Este producto de TRENDnet incluye un programa gratuito desarrollado por terceros. Estos códigos están sujetos a la

Licencia pública general de GNU (“GPL”) o la Licencia pública general limitada de GNU (“LGPL”). Estos códigos son distribuidos SIN GARANTÍA y están sujetos a las leyes de propiedad intelectual de sus desarrolladores. TRENDnet no ofrece servicio técnico para estos códigos. Los detalles sobre las licencias GPL y LGPL de GNU se incluyen en el CD-ROM del producto.

Consulte también el (http://www.gnu.org/licenses/gpl.txt) ó el (http://www.gnu.org/licenses/lgpl.txt) para ver las cláusulas específicas de cada licencia.

Los códigos fuentes están disponibles para ser descargados del sitio Web de TRENDnet

(http://trendnet.com/downloads/list_gpl.asp) durante por lo menos tres años a partir de la fecha de envío del producto.

También puede solicitar el código fuente llamando a TRENDnet.

20675 Manhattan Place, Torrance, CA 90501, USA. Tel: +1-310-961-5500 Fax: +1-310-961-5511

Îáùàÿ èíôîðìàöèÿ î ëèöåíçèÿõ GPL/LGPL

 ñîñòàâ äàííîãî ïðîäóêòà TRENDnet âõîäèò áåñïëàòíîå ïðîãðàììíîå îáåñïå÷åíèå, íàïèñàííîå ñòîðîííèìè

ðàçðàáîò÷èêàìè. Ýòî ÏÎ ðàñïðîñòðàíÿåòñÿ íà óñëîâèÿõ ëèöåíçèé GNU General Public License ("GPL") èëè GNU

Lesser General Public License ("LGPL"). Ïðîãðàììû ðàñïðîñòðàíÿþòñÿ ÁÅÇ ÃÀÐÀÍÒÈÈ è îõðàíÿþòñÿ àâòîðñêèìè

ïðàâàìè ðàçðàáîò÷èêîâ. TRENDnet íå îêàçûâàåò òåõíè÷åñêóþ ïîääåðæêó ýòîãî ïðîãðàììíîãî îáåñïå÷åíèÿ.

Ïîäðîáíîå îïèñàíèå ëèöåíçèé GNU GPL è LGPL ìîæíî íàéòè íà êîìïàêò-äèñêå, ïðèëàãàåìîì ê ïðîäóêòó.

 ïóíêòàõ (http://www.gnu.org/licenses/gpl.txt) è (http://www.gnu.org/licenses/lgpl.txt) èçëîæåíû êîíêðåòíûå óñëîâèÿ

êàæäîé èç ëèöåíçèé.

Èñõîäíûé êîä ïðîãðàìì äîñòóïåí äëÿ çàãðóçêè ñ âåá-ñàéòà TRENDnet (http://trendnet.com/downloads/list_gpl.asp) â

òå÷åíèå, êàê ìèíèìóì, òðåõ ëåò ñî äíÿ ïîñòàâêè ïðîäóêòà.

Êðîìå òîãî, èñõîäíûé êîä ìîæíî çàïðîñèòü ïî àäðåñó TRENDnet.

20675 Manhattan Place, Torrance, CA 90501, USA. Tel: +1-310-961-5500 Fax: +1-310-961-5511

GPL/LGPL informações Gerais

Este produto TRENDnet inclui software gratuito desenvolvido por terceiros. Estes códigos estão sujeitos ao GPL (GNU

General Public License) ou ao LGPL (GNU Lesser General Public License). Estes códigos são distribuídos SEM GARANTIA e estão sujeitos aos direitos autorais dos desenvolvedores. TRENDnet não presta suporte técnico a estes códigos. Os detalhes do GNU GPL e do LGPL estão no CD-ROM do produto.

Favor acessar http://www.gnu.org/licenses/gpl.txt ou http://www.gnu.org/licenses/lgpl.txt para os termos específicos de cada licença.

Os códigos fonte estão disponíveis para download no site da TRENDnet (http://trendnet.com/langen/downloads/list_gpl.asp) por pelo menos três anos da data de embarque do produto.

Você também pode solicitar os códigos fonte contactando TRENDnet, 20675 Manhattan Place, Torrance, CA 90501,

USA.Tel: +1-310-961-5500, Fax: +1-310-961-5511.

GPL/LGPL üldinformatsioon

See TRENDneti toode sisaldab vaba tarkvara, mis on kirjutatud kolmanda osapoole poolt. Koodid on allutatud GNU (General

Public License) Üldise Avaliku Litsentsi (GPL) või GNU (Lesser General Public License) ("LGPL") Vähem Üldine Avalik

Litsentsiga. Koode vahendatakse ILMA GARANTIITA ja need on allutatud arendajate poolt. TRENDnet ei anna koodidele tehnilist tuge. Detailsemat infot GNU GPL ja LGPL kohta leiate toote CD-ROMil. Infot mõlema litsentsi spetsiifiliste terminite kohta leiate (http://www.gnu.org/licenses/gpl.txt) või (http://www.gnu.org/licenses/lgpl.txt).

Infot mõlema litsentsi spetsiifiliste terminite kohta leiate (http://www.gnu.org/licenses/gpl.txt) või

(http://www.gnu.org/licenses/lgpl.txt). Lähtekoodi on võimalik alla laadida TRENDneti kodulehelt

(http://trendnet.com/langen/downloads/list_gpl.asp) kolme aasta jooksul alates toote kättesaamise kuupäevast.

Samuti võite lähtekoodi paluda TRENDneti'lt, 20675 Manhattan Place, Torrance, CA 90501, USA. Tel: +1-310-961-5500,

Fax: +1-310-961-5511.