Quick Start PowerFlex 4 Adjustable Frequency AC Drive FRN 2.xx This Quick Start guide summarizes the basic steps needed to install, start-up and program the PowerFlex 4 Adjustable Frequency AC Drive. The information provided Does Not replace the User Manual and is intended for qualified drive service personnel only. For detailed PowerFlex 4 information including EMC instructions, application considerations and related precautions refer to the PowerFlex 4 User Manual, Publication 22A-UM001x on the CD supplied with the drive or at www.ab.com/manuals/dr. General Precautions ! ATTENTION: The drive contains high voltage capacitors which take time to discharge after removal of mains supply. Before working on drive, ensure isolation of mains supply from line inputs [R, S, T (L1, L2, L3)]. Wait three minutes for capacitors to discharge to safe voltage levels. Failure to do so may result in personal injury or death. Darkened display LEDs is not an indication that capacitors have discharged to safe voltage levels. ! ! ! ! ATTENTION: Equipment damage and/or personal injury may result if this parameter (A092 [Auto Rstrt Tries], A094 [Start At PowerUp]) is used in an inappropriate application. Do not use this function without considering applicable local, national and international codes, standards, regulations or industry guidelines. ATTENTION: Only qualified personnel familiar with adjustable frequency AC drives and associated machinery should plan or implement the installation, start-up and subsequent maintenance of the system. Failure to comply may result in personal injury and/or equipment damage. ATTENTION: This drive contains ESD (Electrostatic Discharge) sensitive parts and assemblies. Static control precautions are required when installing, testing, servicing or repairing this assembly. Component damage may result if ESD control procedures are not followed. If you are not familiar with static control procedures, reference A-B publication 8000-4.5.2, “Guarding Against Electrostatic Damage” or any other applicable ESD protection handbook. ATTENTION: An incorrectly applied or installed drive can result in component damage or a reduction in product life. Wiring or application errors, such as, undersizing the motor, incorrect or inadequate AC supply, or excessive ambient temperatures may result in malfunction of the system. English-2 Mounting Considerations • Mount the drive upright on a flat, vertical and level surface. – Install on 35 mm DIN Rail. or – Install with screws. Minimum Panel Thickness 1.9 mm (0.0747 in.) • • • Screw Size m4 x 0.7 (#8-32) Mounting Torque 1.56-1.96 Nm (14-17 lb.-in.) Protect the cooling fan by avoiding dust or metallic particles. Do not expose to a corrosive atmosphere. Protect from moisture and direct sunlight. Minimum Mounting Clearances See page 12 for mounting dimensions. 25 mm (1.0 in.) 120 mm (4.7 in.) 120 mm (4.7 in.) Mounting Option A No clearance required between drives. Mounting Option B 120 mm (4.7 in.) 120 mm (4.7 in.) Ambient Operating Temperatures Ambient Temperature Minimum Maximum -10°C (14°F) (1) Enclosure Rating Minimum Mounting Clearances IP 20/Open Type Use Mounting Option A IP 30/NEMA 1/UL Type 1(1) Use Mounting Option B 50°C (122°F) IP 20/Open Type Use Mounting Option B 40°C (104°F) Rating requires installation of the PowerFlex 4 IP 30/NEMA 1/UL Type 1 option kit. General Grounding Requirements Important: Remove the MOV to ground jumper if the drive is installed on an ungrounded distribution system. Tighten screw after jumper removal. Jumper Location R/L1 S/L2 T/L3 U/T1 V/T2 W/T3 SHLD CE Conformity Refer to the PowerFlex 4 User Manual on the CD supplied with the drive for details on how to comply with the Low Voltage (LV) and Electromagnetic Compatibility (EMC) Directives. English-3 Specifications, Fuses and Circuit Breakers Drive Ratings Catalog Number Output Ratings Input Ratings Power Dissipation IP20 Open Contactors Watts Branch Circuit Protection Voltage kW (HP) Amps Range kVA Amps Fuses 100 - 115V AC 1-Phase Input, 0 - 230V 3-Phase Output 140M Motor Protectors 22A-V1P5N104 0.2 (0.25) 22A-V2P3N104 0.37 (0.5) 22A-V4P5N104 0.75 (1.0) 10 15 30 140M-C2E-C10 100-C09 140M-C2E-C16 100-C12 140M-D8E-C20 100-C23 25 30 50 10 10 15 30 140M-C2E-B63 140M-C2E-B63 140M-C2E-C16 140M-D8E-C20 100-C09 100-C09 100-C12 100-C23 25 30 50 80 3 6 10 15 25 35 140M-C2E-B25 140M-C2E-B40 140M-C2E-C10 140M-C2E-C16 140M-C2E-C16 140M-F8E-C25 100-C09 100-C09 100-C09 100-C12 100-C16 100-C23 25 30 50 80 115 165 3 6 10 15 15 140M-C2E-B25 140M-C2E-B40 140M-C2E-B63 140M-C2E-C10 140M-C2E-C16 100-C09 100-C09 100-C09 100-C09 100-C16 30 40 60 90 145 1.5 2.3 4.5 90-126 90-126 90-126 0.75 6.0 1.15 9.0 2.25 18.0 200 - 240V AC – 1-Phase(1) Input, 0 - 230V 3-Phase Output 22A-A1P5N104 22A-A2P3N104 22A-A4P5N104 22A-A8P0N104 0.2 (0.25) 0.37 (0.5) 0.75 (1.0) 1.5 (2.0) 1.5 2.3 4.5 8.0 180-265 180-265 180-265 180-265 0.75 1.15 2.25 4.0 5.0 6.0 10.0 18.0 200 - 240V AC – 3-Phase Input, 0 - 230V 3-Phase Output 22A-B1P5N104 22A-B2P3N104 22A-B4P5N104 22A-B8P0N104 22A-B012N104 22A-B017N104 0.2 (0.25) 0.37 (0.5) 0.75 (1.0) 1.5 (2.0) 2.2 (3.0) 3.7 (5.0) 1.5 2.3 4.5 8.0 12.0 17.5 180-265 180-265 180-265 180-265 180-265 180-265 0.75 1.15 2.25 4.0 5.5 8.6 1.8 2.5 5.2 9.5 15.5 21.0 380 - 480V AC – 3-Phase Input, 0 - 460V 3-Phase Output 22A-D1P4N104 22A-D2P3N104 22A-D4P0N104 22A-D6P0N104 22A-D8P7N104 0.37 (0.5) 0.75 (1.0) 1.5 (2.0) 2.2 (3.0) 3.7 (5.0) 1.4 2.3 4.0 6.0 8.7 340-528 340-528 340-528 340-528 340-528 1.4 2.3 4.0 5.9 8.6 1.8 3.2 5.7 7.5 9.0 Approvals Input/Output Ratings LIST ED 966X UL Output Frequency: 0-240 Hz (Programmable) Efficiency: 97.5% (Typical) ® I ND LIST UL508C C ® I ND CO N T E Q ED 966X UL CSA 22.2 CO N T E Q EMC Directive 89/336 LV: EN 50178, EN 60204 EMC: EN 61800-3, EN 50081-1, EN 50082-2 Digital Control Inputs (Input Current = 6mA) Analog Control Inputs SRC (Source) Mode: 18-24V = ON 0-6V = OFF 4-20mA Analog: 250 ohm input impedance 0-10V DC Analog: 100k ohm input impedance External Pot: 1-10k ohms, 2 Watt minimum SNK (Sink) Mode: 0-6V = ON 18-24V = OFF Control Output Programmable Output (form C relay) Resistive Rating: 3.0A at 30V DC, 3.0A at 125V AC, 3.0A at 240V AC Inductive Rating: 0.5A at 30V DC, 0.5A at 125V AC, 0.5A at 240V AC Fuses and Circuit Breakers Recommended Fuse Type: UL Class J, CC, T or Type BS88; 600V (550V) or equivalent. Recommended Circuit Breakers: HMCP circuit breakers or equivalent. Protective Features Motor Protection: I2t overload protection - 150% for 60 Secs, 200% for 3 Secs (Provides Class 10 protection) Overcurrent: 200% hardware limit, 300% instantaneous fault Over Voltage: 100-120V AC Input – Trip occurs at 405V DC bus voltage (equivalent to 150V AC incoming line) 200-240V AC Input – Trip occurs at 405V DC bus voltage (equivalent to 290V AC incoming line) 380-460V AC Input – Trip occurs at 810V DC bus voltage (equivalent to 575V AC incoming line) Under Voltage: 100-120V AC Input – Trip occurs at 210V DC bus voltage (equivalent to 75V AC incoming line) 200-240V AC Input – Trip occurs at 210V DC bus voltage (equivalent to 150V AC incoming line) 380-480V AC Input – Trip occurs at 390V DC bus voltage (equivalent to 275V AC incoming line) Control Ride Through: Minimum ride through is 0.5 Secs - typical value 2 Secs Faultless Power Ride Through: 100 milliseconds Dynamic Braking Internal brake IGBT included with all ratings 0.75 kW (1 HP) and larger. Refer to Appendix B of the PowerFlex 4 User Manual on CD for ordering information. (1) 200-240V AC - 1-Phase drives are also available with an integral EMC filter. Catalog suffix changes from N104 to N114. English-4 Power Wiring Power Wire Rating Recommended Copper Wire Unshielded 600V, 75°C (167°F) THHN/THWN 15 Mils insulated, dry location Shielded 600V, 75°C or 90°C (167°F or 194°F) RHH/RHW-2 Belden 29501-29507 or equivalent Shielded Tray rated 600V, 75°C or 90°C (167°F or 194°F) RHH/RHW-2 Shawflex 2ACD/3ACD or equivalent Power Terminal Block (A Frame Shown) Terminal Description R/L1, S/L2 1-Phase Input R/L1, S/L2, T/L3 3-Phase Input U/T1 To Motor U/T1 V/T2 To Motor V/T2 W/T3 To Motor W/T3 BR+, BR- R/L1 S/L2 T/L3 U/T1 V/T2 W/T3 BR+ BR- Switch any two motor leads to change forward direction. = Dynamic Brake Resistor Connection [0.75 kW (1 HP) ratings and higher] Safety Ground - PE Power Terminal Block Specifications Frame Maximum Wire Size (1) Minimum Wire Size (1) A 3.3 mm2 (12 AWG) 0.8 mm2 (18 AWG) B 5.3 mm2 (10 AWG) 1.3 mm2 (16 AWG) (1) Torque 1.7-2.2 N-m (16-19 lb.-in.) Maximum/minimum sizes that the terminal block will accept - these are not recommendations. Input Power Conditions Input Power Condition Corrective Action Low Line Impedance (less than 1% line reactance) • • Install Line Reactor(2) or Isolation Transformer • • Remove MOV jumper to ground. and Install Isolation Transformer with grounded secondary if necessary. Greater than 120 kVA supply transformer Line has power factor correction capacitors Line has frequent power interruptions Line has intermittent noise spikes in excess of 6000V (lightning) Phase to ground voltage exceeds 125% of normal line to line voltage Ungrounded Distribution System (2) Refer to Appendix B of the PowerFlex 4 User Manual on CD for accessory ordering information. I/O Wiring Recommendations(3) Wire Type(s) Description Belden 8760/9460 (or equiv.) 0.8 mm2 (18AWG), twisted pair, 100% shield with drain. Minimum Insulation Rating 300V 60 degrees C Belden 8770 0.8 mm2 (18AWG), 3 conductor, shielded for (140 degrees F) (or equiv.) remote pot only. (3) If the wires are short and contained within a cabinet which has no sensitive circuits, the use of shielded wire may not be necessary, but is always recommended. I/O Terminal Block Specifications Maximum Wire Size (4) Minimum Wire Size (4) Torque 1.3 mm2 (16 AWG) 0.13 mm2 (26 AWG) 0.5-0.8 N-m (4.4-7 lb.-in.) (4) Maximum / minimum that the terminal block will accept - these are not recommendations. Refer to the PowerFlex 4 User Manual on CD for maximum power and control cable length recommendations English-5 Control Terminal Block (1) Important: I/O Terminal 01 is always a coast to stop input except when P036 [Start Source] is set to “3-Wire” control. In three wire control, I/O Terminal 01 is controlled by P037 [Stop Mode]. All other stop sources are controlled by P037 [Stop Mode]. P036 [Start Source] Keypad Per P037 Coast 3-Wire Per P037 Per P037 2-Wire Per P037 Coast RS485 Port Per P037 Coast Important: The drive is shipped with a jumper installed between I/O Terminals 01 and 11. Remove this jumper when using I/O Terminal 01 as a stop input. 01 (2) Two wire control shown. For three 05 wire control use a momentary input on I/O Terminal 02 to command a start. Use a maintained input for I/O Terminal 03 to change direction. Relay N.O. Relay Common Relay N.C. Refer to the PowerFlex 4 User Manual on CD for detailed I/O wiring examples. I/O Terminal 01 Stop Stop 02 03 04 06 +24V +10V 11 12 13 R1 14 R2 15 R3 16 Stop (1) Typical Typical SRC Wiring SNK Wiring Start/Run FWD (2) Direction/Run REV Digital Common Digital Input 1 Digital Input 2 +24V DC +10V DC 0-10V In Analog Common 4-20mA In RS485 Shield Potentiometer must be 1-10k ohm 2 Watt Min. 01 02 03 04 05 06 R1 R2 R3 30V DC 125V AC 240V AC Resistive 3.0A 3.0A 3.0A Inductive 0.5A 0.5A 0.5A SNK SRC 11 12 13 14 15 16 (1) RS485 (DSI) 81 No. Signal Default Description Param. R1 R2 R3 Fault – Fault Normally open contact for output relay. Common for output relay. Normally closed contact for output relay. A055 Source (SRC) Inputs can be wired as Sink (SNK) or Source (SRC) via DIP Switch setting. The factory installed jumper or a normally closed input must be present for the drive to start. Relay N.O. Relay Common Relay N.C. Sink/Source DIP Switch 01 Stop(1) Coast 02 Start/Run FWD Not Active 03 Direction/Run REV P036, P037 Command comes from the integral keypad by default. To disable reverse operation, see A095 [Reverse Disable]. P036, P037, A095 For digital inputs. Electronically isolated with digital inputs – from analog I/O. Preset Frequencies Program with A051 [Digital In1 Sel]. A051 Preset Frequencies Program with A052 [Digital In2 Sel]. A052 Drive supplied power for digital inputs. – Maximum output current is 100mA. Drive supplied power for 0-10V external potentiometer. – P038 Maximum output current is 15mA. Digital Common 05 06 Digital Input 1 Digital Input 2 11 +24V DC 12 +10V DC 13 0-10V In(3) Not Active 14 Analog Common – 15 4-20mA In(3) Not Active RS485 (DSI) Shield – 16 P036(1) Not Active 04 (3) A055 For external 0-10V input supply P038 (input impedance = 100k ohm) or potentiometer wiper. For 0-10V In or 4-20mA In. Electronically isolated with analog inputs from digital I/O. For external 4-20mA input supply P038 (input impedance = 250 ohm). Terminal should be connected to safety ground - PE when using the RS485 (DSI) communications port. Only one analog frequency source may be connected at a time. If more than one reference is connected at the same time, an undetermined frequency reference will result. English-6 Prepare For Drive Start-Up ! ATTENTION: Power must be applied to the drive to perform the following start-up procedures. Some of the voltages present are at incoming line potential. To avoid electric shock hazard or damage to equipment, only qualified service personnel should perform the following procedure. Thoroughly read and understand the procedure before beginning. If an event does not occur while performing this procedure, Do Not Proceed. Remove All Power including user supplied control voltages. User supplied voltages may exist even when main AC power is not applied to the drive. Correct the malfunction before continuing. Before Applying Power to the Drive ❏ 1. Confirm that all inputs are connected to the correct terminals and are secure. ❏ 2. Verify that AC line power at the disconnect device is within the rated value of the drive. ❏ 3. Verify that any digital control power is 24 volts. ❏ 4. Verify that the Sink (SNK)/Source (SRC) Setup DIP Switch is set to match your control wiring scheme. See page 5 for location. Important: The default control scheme is Source (SRC). The Stop terminal is jumpered (I/O Terminals 01 and 11) to allow starting from the keypad. If the control scheme is changed to Sink (SNK), the jumper must be removed from I/O Terminals 01 and 11 and installed between I/O Terminals 01 and 04. ❏ 5. Verify that the Stop input is present or the drive will not start. Important: If I/O Terminal 01 is used as a stop input, the jumper between I/O Terminals 01 and 11 must be removed. Applying Power to the Drive ❏ 6. Apply AC power and control voltages to the drive. ❏ 7. Familiarize yourself with the integral keypad features (see next page) before setting any Program Group parameters. Start, Stop, Direction and Speed Control Factory default parameter values allow the drive to be controlled from the integral keypad. No programming is required to start, stop, change direction and control speed directly from the integral keypad. Important: To disable reverse operation, see A095 [Reverse Disable]. If a fault appears on power up, refer to page 11 for an explanation of the fault code. For complete troubleshooting information, refer to the PowerFlex 4 User Manual on the CD supplied with the drive. English-7 Integral Keypad ➋ ➊ ➌ RUN FWD REV PROGRAM ➍ ➏ Menu VOLTS AMPS HERTZ ➎ FAULT ➑ ➐ Description Display Group (View Only) Consists of commonly viewed drive operating conditions. ➒ Basic Program Group Consists of most commonly used programmable functions. Advanced Program Group Consists of remaining programmable functions. Fault Designator Consists of list of codes for specific fault conditions. Displayed only when fault is present. No. LED ➊ Run/Direction Status LED State Steady Red Flashing Red ➋ Alphanumeric Display Steady Red Flashing Red ➌ ➍ ➎ ➏ ➐ Displayed Units Steady Red Description Indicates drive is running and commanded motor direction. Drive has been commanded to change direction. Indicates actual motor direction while decelerating to zero. Indicates parameter number, parameter value, or fault code. Single digit flashing indicates that digit can be edited. All digits flashing indicates a fault condition. Indicates the units of the parameter value being displayed. Program Status Steady Red Indicates parameter value can be changed. Fault Status Flashing Red Indicates drive is faulted. Pot Status Steady Green Indicates potentiometer on Integral Keypad is active. Start Key Status Steady Green No. Key ➑ Name Escape Select Up Arrow Down Arrow Enter ➒ Potentiometer Start Reverse Stop Indicates Start key on Integral Keypad is active. The Reverse key is also active unless disabled by A095 [Reverse Disable]. Description Back one step in programming menu. Cancel a change to a parameter value and exit Program Mode. Advance one step in programming menu. Select a digit when viewing parameter value. Scroll through groups and parameters. Increase/decrease the value of a flashing digit. Advance one step in programming menu. Save a change to a parameter value. Used to control speed of drive. Default is active. Controlled by parameter P038. Used to start the drive. Default is active. Controlled by parameter P036. Used to reverse direction of the drive. Default is active. Controlled by parameters P036 and A095. Used to stop the drive or clear a fault. This key is always active. Controlled by parameter P037. English-8 Viewing and Editing Parameters The last user-selected Display Group parameter is saved when power is removed and is displayed by default when power is reapplied. The following is an example of basic integral keypad and display functions. This example provides basic navigation instructions and illustrates how to program the first Program Group parameter. Step Key(s) Example Displays 1. When power is applied, the last user-selected VOLTS AMPS Display Group parameter number is briefly HERTZ displayed with flashing characters. The display PROGRAM FAULT then defaults to that parameter’s current value. (Example shows the value of d001 [Output Freq] with the drive stopped.) 2. Press Esc once to display the Display Group parameter number shown on power-up. The parameter number will flash. VOLTS AMPS HERTZ PROGRAM FAULT 3. Press Esc again to enter the group menu. The group menu letter will flash. VOLTS AMPS HERTZ 4. Press the Up Arrow or Down Arrow to scroll through the group menu (d, P and A). or 5. Press Enter or Sel to enter a group. The right digit of the last viewed parameter in that group will flash. or 6. Press the Up Arrow or Down Arrow to scroll through the parameters that are in the group. or 7. Press Enter or Sel to view the value of a parameter. If you do not want to edit the value, press Esc to return to the parameter number. or 8. Press Enter or Sel to enter program mode to edit the parameter value. The right digit will flash and the Program LED will illuminate if the parameter can be edited. or 9. Press the Up Arrow or Down Arrow to change the parameter value. If desired, press Sel to move from digit to digit or bit to bit. The digit or bit that you can change will flash. or PROGRAM FAULT VOLTS AMPS HERTZ PROGRAM FAULT VOLTS AMPS HERTZ PROGRAM FAULT VOLTS AMPS HERTZ PROGRAM FAULT 10. Press Esc to cancel a change. The digit will stop flashing, the previous value is restored and the Program LED will turn off. Or Press Enter to save a change. The digit will stop flashing and the Program LED will turn off. VOLTS AMPS HERTZ PROGRAM 11. Press Esc to return to the parameter list. Continue to press Esc to back out of the programming menu. If pressing Esc does not change the display, then d001 [Output Frequency] is displayed. Press Enter or Sel to enter the group menu. FAULT VOLTS AMPS HERTZ PROGRAM FAULT English-9 See the PowerFlex 4 User Manual on CD for more information on parameters. Smart Start-Up with Basic Program Group Parameters The PowerFlex 4 is designed so that start up is simple and efficient. The Program Group contains the most commonly used parameters. = Stop drive before changing this parameter. No. Parameter Min/Max P031 [Motor NP Volts] 20/Drive Rated Volts Set to the motor nameplate rated volts. P032 [Motor NP Hertz] 10/240 Hz Set to the motor nameplate rated frequency. P033 [Motor OL Current] 0.0/(Drive Rated Amps×2) Set to the maximum allowable motor current. P034 [Minimum Freq] 0.0/240.0 Hz Sets the lowest frequency the drive will output continuously. P035 [Maximum Freq] 0/240 Hz Sets the highest frequency the drive will output. P036 [Start Source] 0/5 Sets the control scheme used to start the drive. (1) When active, the Reverse key is also active unless disabled by A095 [Reverse Disable]. P037 [Stop Mode] 0/7 Active stop mode for all stop sources [e.g. keypad, run forward (I/O Terminal 02), run reverse (I/O Terminal 03), RS485 port] except as noted below. Important: I/O Terminal 01 is always a coast to stop input except when P036 [Start Source] is set for “3-Wire” control. When in three wire control, I/O Terminal 01 is controlled by P037 [Stop Mode]. Display/Options Default 1 VAC Based on Drive Rating 1 Hz 60 Hz 0.1 Amps Based on Drive Rating 0.1 Hz 0.0 Hz 1 Hz 60 Hz 0 0 = “Keypad”(1) 1 = “3-Wire” 2 = “2-Wire” 3 = “2-Wire Level Sensitive” 4 = “2-Wire High Speed” 5 = “RS485 (DSI) Port” 0 0 = “Ramp, Clear Fault”(1) 1 = “Coast, Clear Fault”(1) 2 = “DC Brake, Clear Fault”(1) 3 = “DC Brake w/Shutoff, Clear Fault”(1) 4 = “Ramp” 5 = “Coast” 6 = “DC Brake” 7 = “DC Brake w/Shutoff” (1) Stop input also clears active fault. P038 [Speed Reference] 0/5 Sets the source of the speed reference to the drive. Important: When A051 or A052 [Digital Inx Sel] is set to option 2, 4, 5 or 6, and the digital input is active, A051 or A052 will override the speed reference commanded by this parameter. Refer to Chapter 1 of the PowerFlex 4 User Manual on CD for details. P039 [Accel Time 1] 0.0/600.0 Secs Sets the rate of accel for all speed increases. P040 [Decel Time 1] 0.1/600.0 Secs Sets the rate of decel for all speed decreases. P041 [Reset To Defaults] 0/1 Resets all parameter values to factory defaults. 0 0 = “Drive Potentiometer” 1 = “Internal Freq” 2 = “0-10V Input/Remote Potentiometer” 3 = “4-20mA Input” 4 = “Preset Freq 0-3” 5 = “RS485 (DSI) Port” 0.1 Secs 10.0 Secs 0.1 Secs 10.0 Secs 0 = “Idle State” 1 = “Reset Defaults” 0 Advanced Group Parameters No. Min/Max Display/Options A051 [Digital In1 Sel] I/O Terminal 05 A052 [Digital In2 Sel] I/O Terminal 06 Parameter 0/7 0 = “Not Used” 1 = “Accel 2 & Decel 2” 2 = “Jog” 3 = “Auxiliary Fault” 4 = “Preset Frequencies” 4 5 = “Local” 6 = “RS485 (DSI) Port” 7 = “Clear Fault” A055 [Relay Out Sel] 0/9 A056 A067 A068 A069 0.0/9999 0.0/600.0 Secs 0.1/600.0 Secs 0.0/240.0 Hz 0 = “Ready” (Not Faulted) 1 = “At Frequency” 2 = “Motor Running” 3 = “Reverse” 4 = “Motor Overload” 0.1 – 1 0.1 Secs 0.1 Secs 0.1 Hz 0 5 = “Ramp Regulated” 6 = “Above Frequency” 7 = “Above Current” 8 = “Above DC Bus Volts” 9 = “Retries Exhausted” 0.0 20.0 Secs 20.0 Secs 60.0 Hz [Relay Out Level] [Accel Time 2] [Decel Time 2] [Internal Freq] Default English-10 See the PowerFlex 4 User Manual on CD for more information on parameters. No. Parameter A070 A071 A072 A073 [Preset Freq 0](1) 0.0/240.0 Hz 0.1 Hz [Preset Freq 1] [Preset Freq 2] [Preset Freq 3] (1) To activate [Preset Freq 0] set P038 [Speed Reference] to option 4. Min/Max Display/Options Default 0.0 Hz 5.0 Hz 10.0 Hz 20.0 Hz (2) Input State of Digital In 1 Input State of Digital In 2 Frequency Source Accel / Decel Parameter Used (I/O Terminal 05) (I/O Terminal 06) 0 0 [Preset Freq 0] [Accel Time 1] / [Decel Time 1] 1 0 [Preset Freq 1] [Accel Time 1] / [Decel Time 1] 0 1 [Preset Freq 2] [Accel Time 2] / [Decel Time 2] 1 1 [Preset Freq 3] [Accel Time 2] / [Decel Time 2] (2) When a Digital Input is set to “Accel 2 & Decel 2”, and the input is active, that input overrides the settings in this table. A078 A079 A080 A081 A082 [Jog Frequency] [Jog Accel/Decel] [DC Brake Time] [DC Brake Level] [DB Resistor Sel] A083 [S Curve %] A084 [Start Boost] 0.0/[Maximum Freq] 0.1/600.0 Secs 0.0/90.0 Secs 0.0/(Drive Amps × 1.8) 0/99 0.1 Hz 0.1 Secs 0.1 Secs 0.1 Amps 0 = Disabled 1 = 5% Duty Cycle 2 = 100% Duty Cycle 3-99 = % of Duty Cycle 1% Settings in % of base voltage. Variable Torque Constant Torque 1 = “30.0” 5 = “0.0 no IR Comp” 10 = “10.0” 2 = “35.0” 6 = “0.0” 11 = “12.5” 3 = “40.0” 7 = “2.5” 12 = “15.0” 4 = “45.0” 8 = “5.0” 13 = “17.5” 9 = “7.5” 14 = “20.0” 20/Rated Volts 1 VAC 0.1/(Drive Amps × 1.8) 0.1 Amps 0/2 0 = “No Derate” 1 = “Minimum Derate” 2 = “Maximum Derate” 2.0/16.0 kHz 0.1 kHz 0/9 1 0.0/120.0 Secs 0.1 Secs 0/1 0 = “Disabled” 1 = “Enabled” 4.0 kHz 0 1.0 Secs 0 A095 [Reverse Disable] 0/1 0 = “Reverse Enabled” 1 = “Reverse Disabled” 0 A096 [Flying Start En] A097 [Compensation] 0/1 0/3 1 = “Enabled” 2 = “Mechanical” 3 = “Both” 0 1 A098 [SW Current Trip] A099 [Process Factor] A100 [Fault Clear] 0.0/(Drive Amps × 2) 0.1/999.9 0/2 0 = “Disabled” 0 = “Disabled” 1 = “Electrical” 0.1 Amps 0.1 0 = “Ready” A088 [Maximum Voltage] A089 [Current Limit] A090 [Motor OL Select] A091 A092 A093 A094 [PWM Frequency] [Auto Rstrt Tries] [Auto Rstrt Delay] [Start At PowerUp] 0/100% 1/14 10.0 Hz 10.0 Secs 0.0 Secs Amps × 0.05 0 A101 [Program Lock] 0/1 A102 [Testpoint Sel] 0/FFFF A103 [Comm Data Rate](3) 0/5 1 = “Reset Active Fault” 2 = “Clear Fault Queue” Rated Volts Amps × 1.5 0 0.0 (Disabled) 30.0 0 A106 [Comm Loss Time] A107 [Comm Format](3) 0.1/60.0 0/2 0 = “Unlocked” 1 Hex 0 = “1200” 1 = “2400” 2 = “4800” 1 0 = “Fault” 1 = “Coast to Stop” 0.1 0 = “RTU 8-N-1” A110 [0-10V Analog Input Low] 0.0/100.0% 0.1% A111 [0-10V Analog Input High] 0.0/100.0% 0.1% 100.0 A112 [4-20mA Analog Input 0.0/100.0% Low] 0.1% 0.0 A113 [4-20mA Analog Input 0.0/100.0% High] 0.1% 100.0 A104 [Comm Node Addr](3) 1/247 A105 [Comm Loss Action] 0/3 A114 [Slip Compensation] 0.0/10.0 Hz 0.1 Hz (3) Power to drive must be cycled before any changes will affect drive operation. 1 = “Locked” 0% (Disabled) 8 7 (5 HP Drives) 3 = “9600” 4 = “19.2K” 5 = “38.4K” 0 400 3 100 2 = “Stop” 0 3 = “Continue Last Speed” 5.0 1 = “RTU 8-E-1” 0 2 = “RTU 8-O-1” 0.0 2.0 Hz English-11 See the PowerFlex 4 User Manual on CD for more information on parameters. Display Group Parameters No. Parameter Min/Max Display/Options d001 d002 d003 d004 d005 d006 [Output Freq] [Commanded Freq] [Output Current] [Output Voltage] [DC Bus Voltage] [Drive Status] 0.0/[Maximum Freq] 0.0/[Maximum Freq] 0.00/Drive Amps × 2 0/Drive Rated Volts Based on Drive Rating 0/1 (1 = Condition True) 0.1 Hz 0.1 Hz 0.01 Amps 1 VAC 1 VDC Bit 3 Decelerating F1 d007- [Fault x Code] d009 d010 [Process Display] d012 [Control Source] F2/F122 d013 [Contrl In Status] 0/1 (1 = Input Present) d014 [Dig In Status] 0/1 (1 = Input Present) d015 [Comm Status] 0/1 (1 = Condition True) d016 d017 d018 d019 d020 d021 1.00/99.99 1001/9999 0/9999 Hrs 0/FFFF 0.0/100.0% 0.0/100.0% [Control SW Ver] [Drive Type] [Elapsed Run Time] [Testpoint Data] [0-10V Analog Input] [4-20mA Analog Input] 0.00/9999 0/9 Bit 2 Accelerating 0.01 – 1 Bit 1 = Speed Command (See P038; 9 = “Jog Freq”) Bit 2 Bit 3 Reserved Stop Input Bit 2 Bit 3 Reserved Reserved Bit 2 Bit 3 Fault Occurred RS485 Option 0.01 1 1 = 10 Hrs 1 Hex 0.1% 0.1% Bit 1 Forward Bit 0 Running Bit 0 = Start Command (See P036; 9 = “Jog”) Bit 1 Bit 0 Dir/Run REV Start/Run FWD Bit 1 Bit 0 Digital In2 Sel Digital In1 Sel Bit 1 Bit 0 Transmitting Receiving Fault Codes To clear a fault, press the Stop key, cycle power or set A100 [Fault Clear] to 1 or 2. No. Fault Description F2 F3 F4 F5 Auxiliary Input(1) Power Loss UnderVoltage(1) OverVoltage(1) F6 Motor Stalled(1) F7 Motor Overload(1) F8 Heatsink OvrTmp(1) F12 HW OverCurrent(1) F13 F33 F38 F39 F40 F41 F42 F43 F48 Ground Fault Auto Rstrt Tries Phase U to Gnd Phase V to Gnd Phase W to Gnd Phase UV Short Phase UW Short Phase VW Short Params Defaulted Check remote wiring. Monitor the incoming AC line for low voltage or line power interruption. Monitor the incoming AC line for low voltage or line power interruption. Monitor the AC line for high line voltage or transient conditions. Bus overvoltage can also be caused by motor regeneration. Extend the decel time or install dynamic brake option. Increase [Accel Time x] or reduce load so drive output current does not exceed the current set by parameter A089 [Current Limit]. An excessive motor load exists. Reduce load so drive output current does not exceed the current set by parameter P033 [Motor OL Current]. Check for blocked or dirty heat sink fins. Verify that ambient temperature has not exceeded 40°C (104°F) for IP 30/NEMA 1/UL Type 1 installations or 50°C (122°F) for Open type installations. Check fan. Check programming. Check for excess load, improper DC boost setting, DC brake volts set too high or other causes of excess current. Check the motor and external wiring to the drive output terminals for a grounded condition. Correct the cause of the fault and manually clear. Check the wiring between the drive and motor. Check motor for grounded phase. Replace drive if fault cannot be cleared. Check the motor and drive output terminal wiring for a shorted condition. Replace drive if fault cannot be cleared. The drive was commanded to write default values to EEPROM. Clear the fault or cycle power to the drive. Program the drive parameters as needed. F63 SW OverCurrent(1) Check load requirements and A098 [SW Current Trip] setting. F64 Drive Overload Reduce load or extend Accel Time. F70 Power Unit Cycle power. Replace drive if fault cannot be cleared. F81 Comm Loss If adapter was not intentionally disconnected, check wiring to the port. Replace wiring, port expander, adapters or complete drive as required. Check connection. An adapter was intentionally disconnected. Turn off using A105 [Comm Loss Action]. F100 Parameter Checksum Restore factory defaults. F122 I/O Board Fail Cycle power. Replace drive if fault cannot be cleared. (1) Auto-Reset/Run type fault. Configure with parameters A092 and A093. English-12 Drive Dimensions Dimensions are in millimeters and (inches). Weights are in kilograms and (pounds). A D C F GEB 5.5 (0.22) Frame A B(1) C D E(2) F G Shipping Weight A 80 (3.15) 185 (7.28) 136 (5.35) 67 (2.64) 152 (5.98) 59.3 (2.33) 140 (5.51) 1.4 (3.1) B 100 (3.94) 213 (8.39) 136 (5.35) 87 (3.43) 180 (7.09) 87.4 (3.44) 168 (6.61) 2.2 (4.9) (1) (2) Overall height of drive with IP 30/NEMA 1/UL Type 1 option kit installed. Overall height of standard IP 20/Open Type drive. PowerFlex 4 Frames – Ratings are in kW and (HP) Frame 120V AC – 1-Phase 240V AC – 1-Phase 240V AC – 3-Phase 480V AC – 3-Phase A 0.2 (0.25) 0.37(0.5) 0.2 (0.25) 0.37 (0.5) 0.75 (1.0) 0.2 (0.25) 0.37 (0.5) 0.75 (1.0) 1.5 (2.0) 0.37 (0.5) 0.75 (1.0) 1.5 (2.0) B 0.75(1.0) 1.5 (2.0) 2.2 (3.0) 3.7 (5.0) 2.2 (3.0) 3.7 (5.0) Optional Conduit Box – Dimensions are in millimeters and (inches) 59.2 (2.33) 40.0 (1.57) 20.7 (0.81) Frame A ∅ 22.2 (0.88) 79.1 (3.11) 64.1 (2.52) 40.6 (1.60) ∅ 22.2 (0.88) 25.6 (1.01) 34.0 (1.34) 35.6 (1.40) 75.3 (2.96) 74.3 (2.93) Frame B U.S. Allen-Bradley Drives Technical Support Tel: (1) 262.512.8176, Fax: (1) 262.512.2222, Email: [email protected], Online: www.ab.com/support/abdrives Publication 22A-QS001B-EN-P – May 2002 Supersedes December 2001 Copyright © 2002 Rockwell Automation, Inc. All rights reserved. Printed in Taiwan.
* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project