Watlow Electric | 160 Series | User`s manual | Watlow Electric 160 Series User`s manual

Watlow Electric 160 Series User`s manual
EZ-ZONE PM
®
User’s Manual
PID Controller Models
TOTAL
CUSTOMER
SATISFACTION
3 Year Warranty
ISO 9001
Registered Company
Winona, Minnesota USA
1241 Bundy Boulevard., Winona, Minnesota USA 55987
Phone: +1 (507) 454-5300, Fax: +1 (507) 452-4507 http://www.watlow.com
0600-0058-0000 Rev. J
March 2010
Made in the U.S.A.
Safety Information
Unit is a Listed device per Underwriters Laboratories®. It has
been evaluated to United States
and Canadian requirements for
Hazardous Locations Class 1
Division II Groups A, B, C and
D. ANSI/ISA 12.12.01-2007. File
E184390 QUZW, QUZW7. See:
www.ul.com
We use note, caution and warning symbols throughout this book to draw your attention to important
operational and safety information.
A “NOTE” marks a short message to alert you to
an important detail.
A “CAUTION” safety alert appears with information that is important for protecting your equipment and performance. Be especially careful to
read and follow all cautions that apply to your
application.
Unit is compliant with European
Union directives. See Declaration
of Conformity for further details
on Directives and Standards used
for Compliance.
A “WARNING” safety alert appears with information that is important for protecting you, others and equipment from damage. Pay very close
attention to all warnings that apply to your
application.
The electrical hazard symbol, Ó (a lightning bolt
in a triangle) precedes an electric shock hazard
CAUTION or WARNING safety statement.
Symbol
Unit has been reviewed and approved by Factory Mutual as a
Temperature Limit Device per FM
Class 3545 standard. See: www.
fmglobal.com
Unit has been reviewed and approved by CSA International for
use as Temperature IndicatingRegulating Equipment per CSA
C22.2 No. 24. See: www.csa-international.org
Explanation
Unit has been reviewed and approved by ODVA for compliance
with DeviceNet communications
protocol. See: www.odva.org
CAUTION – Warning or Hazard
that needs further explanation
than label on unit can provide.
Consult users manual for further
information.
ESD Sensitive product, use proper
grounding and handling techniques when installing or servicing product.
Unit protected by double/reinforced insulation for shock hazard
prevention.
Do not throw in trash, use proper
recycling techniques or consult
manufacturer for proper disposal.
Enclosure made of Polycarbonate
material. Use proper recycling
techniques or consult manufacturer for proper disposal.
Unit can be powered with either
alternating current (ac) voltage or
direct current (dc) voltage.
Unit is a Listed device per Underwriters Laboratories®. It has
been evaluated to United States
and Canadian requirements for
Process Control Equipment. UL
61010 and CSA C22.2 No. 61010.
File E185611 QUYX, QUYX7.
See: www.ul.com
Unit has been reviewed and approved by ODVA for compliance
with Ethernet/IP communications
protocol. See: www.odva.org
Warranty
The EZ-ZONE® PM is manufactured by ISO
9001-registered processes and is backed by a threeyear warranty to the first purchaser for use, providing that the units have not been misapplied. Since
Watlow has no control over their use, and sometimes
misuse, we cannot guarantee against failure. Watlow’s obligations hereunder, at Watlow’s option, are
limited to replacement, repair or refund of purchase
price, and parts which upon examination prove to be
defective within the warranty period specified. This
warranty does not apply to damage resulting from
transportation, alteration, misuse or abuse. The purchaser must use Watlow parts to maintain all listed
ratings.
Technical Assistance
If you encounter a problem with your Watlow controller, review your configuration information to verify
that your selections are consistent with your application: inputs, outputs, alarms, limits, etc. If the problem persists, you can get technical assistance from
your local Watlow representative (see back cover), by
e-mailing your questions to wintechsupport@watlow.
com or by dialing +1 (507) 494-5656 between 7 a.m.
and 5 p.m., Central Standard Time (CST). Ask for for
an Applications Engineer. Please have the following
information available when calling:
• Complete model number
• All configuration information
• User’s Manual
• Factory Page
Return Material Authorization (RMA)
1. Call Watlow Customer Service, (507) 454-5300, for
a Return Material Authorization (RMA) number
before returning any item for repair. If you do not
know why the product failed, contact an Application
Engineer or Product Manager. All RMA’s require:
• Ship-to address
• Bill-to address
• Contact name
• Phone number
• Method of return shipment
• Your P.O. number
• Detailed description of the problem
• Any special instructions
• Name and phone number of person returning the
product.
2. Prior approval and an RMA number from the
Customer Service Department is required when
returning any product for credit, repair or evaluation. Make sure the RMA number is on the outside of
the carton and on all paperwork returned. Ship on a
Freight Prepaid basis.
3. After we receive your return, we will examine it and
try to verify the reason for returning it.
4. In cases of manufacturing defect, we will enter a
repair order, replacement order or issue credit for
material returned. In cases of customer mis-use,
we will provide repair costs and request a purchase
order to proceed with the repair work.
5. To return products that are not defective, goods
must be be in new condition, in the original boxes
and they must be returned within 120 days of
receipt. A 20 percent restocking charge is applied for
all returned stock controls and accessories.
6. If the unit is unrepairable, you will receive a letter of
explanation. and be given the option to have the unit
returned to you at your expense or to have us scrap
the unit.
7. Watlow reserves the right to charge for no trouble
found (NTF) returns.
The EZ-ZONE® PM PID Controller User’s Manual is
copyrighted by Watlow Winona, Inc., © March 2010 with
all rights reserved.
EZ-ZONE® PM is covered by U.S. Patent No. 6,005,577
and Patents Pending
TC
Table of Contents
Chapter 1: Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Standard Features and Benefits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
A Conceptual View of the PM. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Getting Started Quickly. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Chapter 2: Install and Wire. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Dimensions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Wiring. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Chapter 3: Keys and Displays. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Chapter 4: Home Page. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Conventions Used in the Menu Pages . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Chapter 5: Operations Page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Analog Input Menu. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Linearization Menu. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Process Value Menu. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Digital Input/Output Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Monitor Menu. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Control Loop Menu. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Alarm Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Profile Status Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Chapter 6: Setup Page. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Analog Input Menu. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Linearization Menu. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Process Value Menu. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Digital Input/Output Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Control Loop Menu. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
Output Menu. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
Alarm Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
Function Key Menu. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
Global Menu. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
Communications Menu. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
Real Time Clock Menu. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
Watlow EZ-ZONE ® PM PID Controller
•
1 •
Table of Contents
TC
Table of Contents (cont.)
Chapter 7: Profiling Page. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
Profiling Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
Chapter 8: Factory Page. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
Custom Menu. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
Security Setting Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
Security Setting Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
Diagnostics Menu. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
Calibration Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
Chapter 9: Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73
Saving and Restoring User Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . 74
Programming the Home Page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74
Tuning the PID Parameters. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74
Inputs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76
Outputs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
Control Methods. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79
Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82
Open Loop Detection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83
Programming the EZ Key/s. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84
Using Lockout to Hide Pages and Menus. . . . . . . . . . . . . . . . . . . . . . . . 84
Using Password Security . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85
Modbus - Using Programmable Memory Blocks. . . . . . . . . . . . . . . . . . 86
Software Configuration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87
Chapter 10: Appendix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90
Troubleshooting Alarms, Errors and Control Issues. . . . . . . . . . . . . . . . 90
Modbus - Programmable Memory Blocks. . . . . . . . . . . . . . . . . . . . . . . 93
Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95
Ordering Information for PID Controller Models . . . . . . . . . . . . . . . . . . 97
Index. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98
How to Reach Us. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103
Watlow EZ-ZONE ® PM PID Controller
•
2 •
Table of Contents
1
Chapter 1: Overview
The EZ-ZONE ® PM takes the pain out of solving
your thermal loop requirements.
Watlow’s EZ-ZONE PM controllers offer options
to reduce system complexity and the cost of controlloop ownership. You can order the EZ-ZONE PM as
a PID controller or an over-under limit controller, or
you can combine both functions in the PM Integrated Limit Controller. You now have the option to integrate a high-amperage power controller output, an
over-under limit controller and a high-performance
PID controller all in space-saving, panel-mount
packages. You can also select from a number of serial communications options to help you manage system performance.
It just got a whole lot easier to solve the thermal
requirements of your system. Because the EZ-ZONE
PM controllers are highly scalable, you only pay for
what you need. So if you are looking for a PID controller, an over-under limit controller or an integrated controller, the EZ-ZONE PM is the answer.
Agency approvals: UL Listed, CSA, CE, RoHS,
W.E.E.E. FM
• Assures prompt product acceptance
Standard Features and Benefits
Removable cage clamp wiring connectors
• Reliable wiring, reduced service calls
Advanced PID Control Algorithm
• TRU-TUNE+ ® Adaptive tune provides tighter control for demanding applications.
• Simplified installation
• Reduces end product documentation costs
• Semi F47-0200
P3T Armor Sealing System
• NEMA 4X and IP66 offers water and dust resistance, can be cleaned and washed down (indoor
use only)
• Backed up by UL 50 independent certification to
NEMA 4X specification
Three-year warranty
• Demonstrates Watlow’s reliability and product
support
Touch-safe Package
• IP2X increased safety for installers and operators
EZ-Key/s
• Programmable EZ-Key enables simple one-touch
operation of repetitive user activities
• Auto Tune for fast, efficient start ups
High-amperage Power Control Output
• Drives 15 amp resistive loads directly
Programmable Menu System
• Reduces set up time and increases operator efficiency
• Reduces component count
• Saves panel space and simplifies wiring
Full-featured Alarms
• Improves operator recognition of system faults
• Reduces the cost of ownership
EZ-ZONE configuration communications and
software
• Saves time and improves the reliability of controller set up
• Control of auxiliary devices
Heat-Cool Operation
• Provides application flexibility with accurate temperature and process control
Parameter Save & Restore Memory
• Reduces service calls and down time
Profile Capability
• Preprogrammed process control
• Ramp and soak programming with four files and
40 total steps
Watlow EZ-ZONE ® PM PID Controller
•
3
•
Chapter 1 Over view
A Conceptual View of the PM
The flexibility of the PM’s software and hardware allows a large range of configurations. Acquiring a better understanding of the controller’s overall functionality and capabilities while at the same time planning out how the controller can be used will deliver
maximum effectiveness in your application.
It is useful to think of the controller in three
parts: inputs; procedures; and outputs. Information
flows from an input to a procedure to an output when
the controller is properly configured. A single PM
controller can carry out several procedures at the
same time, for instance closed-loop control, monitoring for several different alarm situations and operating switched devices, such as lights and motors.
Each process needs to be thought out carefully and
the controller’s inputs, procedures and outputs set up
properly.
Inputs
The inputs provide the information that any given
programmed procedure can act upon. In a simple
form, this information may come from an operator
pushing a button or as part of a more complex procedure it may represent a remote set point being received from another controller.
Each analog input typically uses a thermocouple
or RTD to read the temperature of something. It can
also read volts, current or resistance, allowing it to
use various devices to read humidity, air pressure,
operator inputs and others values. The settings in
the Analog Input Menu (Setup Page) for each analog
input must be configured to match the device connected to that input.
Each digital input reads whether a device is active
or inactive. A PM with digital input-output hardware
includes two sets of terminals each of which can be
used as either an input or an output. Each pair of
terminals must be configured to function as either
an input or output with the Direction parameter in
the Digital Input/Output Menu (Setup Page).
The Function or EZ Key on the front panel of the
PM also operates as a digital input by toggling the
function assigned to it in the Digital Input Function
parameter in the Function Key Menu (Setup Page).
side of the controller. To have any effect outside of the
controller, an output must be configured to respond
to a function.
Outputs
Outputs can perform various functions or actions in
response to information provided by a function, such
as operating a heater; turning a light on or off; unlocking a door; or turning on a buzzer.
Assign an output to a Function in the Output
Menu or Digital Input/Output Menu. Then select
which instance of that function will drive the selected output. For example, you might assign an output
to respond to alarm 4 (instance 4) or to retransmit
the value of analog input 2 (instance 2).
You can assign more than one output to respond
to a single instance of a function. For example, alarm
2 could be used to trigger a light connected to output
1 and a siren connected to digital output 5.
Input Events and Output Events
Input and output events are internal states that are
used exclusively by profiles. The source of an event
input can come from a real-world digital input or an
output from another function. Likewise, event outputs may control a physical output such as an output
function block or be used as an input to another function.
Functions
Functions use input signals to calculate a value. A
function may be as simple as reading a digital input
to set a state to true or false, or reading a temperature to set an alarm state to on or off. Or, it could
compare the temperature of a process to the set point
and calculate the optimal power for a heater.
To set up a function, it’s important to tell it what
source, or instance, to use. For example, an alarm
may be set to respond to either analog input 1 or 2
(instance 1 or 2, respectively).
Keep in mind that a function is a user-programmed
internal process that does not execute any action outWat low EZ-ZONE ® PM PID Controller
•
4
•
Chapter 1 Over view
Getting Started Quickly
the default value of 75 °F to the desired value. As the
Set Point increases above the Process Value, output 1
will come on and it will now begin driving your output device. The PV function as shown in the graphic
below is only available with PM4/8/9 models.
The PM control has a page and menu structure that
is listed below along with a brief description of its
purpose.
Setup Page
Push and hold the up
and down keys (¿ ¯)
for 6 seconds to enter.
(See the Setup Page for
further information)
Once received, a user
would want to setup
their control prior to operation. As an example,
define the input type
and set the output cycle
time.
Note:
The output cycle time will have a bearing on the
life of mechanical relay outputs and can be different based on the type of output ordered. The output
cycle time can be changed in the Setup Page under
the Output Menu.
Operations Page
Push and hold the up
and down keys (¿ ¯)
for 3 seconds to enter.
(See the Operations
Page for further information)
After setting up the
control to reflect your
equipment, the Operations Page would
be used to monitor or
change runtime settings.
As an example, the user
may want to see how
much time is left in a
profile step or perhaps
change the autotune set
point.
Factory Page
Push and hold the Infinity and the green
Advance keys (ˆ ‰) for
6 seconds to enter. (See
the Factory Page for further information)
For the most part the
Factory Page has no
bearing on the control when running. A
user may want to enable password protection, view the control
part number or perhaps
create a custom Home
Page.
Home Page
The control is at the
Home Page when initially powered up.
Pushing the green
Advance key ‰ will allow the user to see and
change such parameters
as the control mode, enable autotune and idle
set point to name a few.
Profile Page
Push and hold the the
green Advance key ‰ for
6 seconds to enter. (See
the Profile Page for further information)
If equipped with this
feature a user would
want to go here to configure a profile.
EZ-ZONE PM Default Configuration
Input
Function
Input Sensor
Process
Value
Analog Input 1
Thermocouple Type J
(PV)
Function
PID
Controller
Heat
Output
Function
Output 1
Heat
Loop 1
Off
The default PM loop configuration out of the box is
shown below:
• Analog Input functions set to thermocouple, type
J
•Heat algorithm set for PID, Cool set to off
•Output 1 set to Heat
•Control mode set to Auto
•Set point set to 75 °F
If you are using the input type shown above, simply
connect your input and output devices to the control.
Power up the control and push the up arrow ¿ on
the face of the control to change the set point from
Watlow EZ-ZONE ® PM PID Controller
•
5
•
Chapter 1 Over view
EZ-ZONE® PM PID Model System Diagram
Universal Sensor Input, Configuration Communications,
Red/Green 7-Segment Display
Output
Functions
Input
Functions
Input sensor
None
Profile start/stop
Profile start
Profile hold/resume
Profile disable
TRU-TUNE+® disable
Control outputs off
Manual/auto mode
Tune
Idle set point
Force alarm
Loop & alarms off
Silence alarm
Alarm reset
Lock keypad
Restore user settings
Network
remote user interface,
personal computer,
programmable logic
controller, humanmachine interface
Analog Input 1
none, Thermocouple, RTD (100Ω,
1kΩ), Thermister 5kΩ, 10kΩ, 20kΩ,
40kΩ) Process (V, mV, mA) or 1k
Potentiometer
PID
Controller
Board
Slot A
ramp-soak
with 4 files
(optional)
Output 1 none, switched dc/open collector, form C mechanical (5 A) relay, form A
solid-state (0.5 A) relay, process (V, mA)
off, heat, cool,
duplex, alarm,
retransmit,
event
Output 2 none, switched dc, NO-ARC
power control (15 A), form A mechanical
(5 A) or Solid-State Relay (0.5 A)
off, heat, cool,
alarm, event
Digital Input (or Output) 5 & 6
(optional) none, switch, volts dc
EZ Key/s (PM4,6,8 and 9 only)
programmable event
Supervisory
&
Power
Board
Slot C
off, heat, cool,
alarm, event
Digital Output (or Input) 5 & 6
(optional) none, switched dc
EIA 485 Communications
Standard Bus, Modbus RTU (optional)
Output Status
Wat low EZ-ZONE ® PM PID Controller
•
6
•
1
2
3
4
5
6
Zone
Address
Indicates Zone
Address
Indicates I/O
Status
Chapter 1 Over view
2
Dimensions
Chapter 2: Install and Wire
1/32 DIN
15.9 mm
0.63 in
53.3 mm
2.10 in
101.6 mm
4.00 in
31.2 mm
1.23 in
30.9 mm
1.22 in
Side
Front
Top
45.2 mm
(1.78 in)
22.4 mm
(0.88 in)
Recommended panel spacing
panel thickness 1.53 to 9.52 mm
(0.060 to 0.375)
21.6 mm
(0.85 in)
21.6 mm
(0.85 in)
Watlow EZ-ZONE ® PM PID Controller
• 7 • Cutout
1/32 DIN Maximum
Chapter 2 Install and Wire
1/16 DIN
15.8 mm
(0.62 in)
101.6 mm
(4.00 in)
53.3 mm
(2.10 in)
53.3 mm
(2.10 in)
Side
Front
51.2 mm
(2.02 in)
Top
L1
L3
K1
K3
99
J1
J3
CF
98
L2
L4
CD
K2
K4
CE
T1
T2
B5
S1
S2
D6
R1
R2
D5
Back
45.2 mm
(1.78 in)
45.2 mm
(1.78 in)
panel thickness 1.53 to 9.52 mm
(0.060 to 0.375)
21.6 mm
(0.85 in)
21.6 mm
(0.85 in)
Wat low EZ-ZONE ® PM PID Controller
•
8
•
Chapter 2 Install and Wire
1/8 DIN (PM8) Vertical
15.75 mm
(0.62 in)
1.52 mm
(0.06 in)
53.34 mm
(2.10 in)
100.33 mm
(3.95 in)
10.16 mm
(0.40 in)
30.73 mm
(1.21 in)
54.86 mm
(2.16 in)
101.60 mm
(4.00 in)
1/8 DIN (PM8) Vertical Recommended Panel Spacing
45.2 mm
(1.78 in)
92.3 mm
(3.635 in)
Panel thickness (0.060 in) 1.53 mm
to (0.375 in) 9.52 mm
21.6 mm
(0.85 in)
21.6 mm
(0.85 in)
Watlow EZ-ZONE ® PM PID Controller
•
9
•
Chapter 2 Install and Wire
1/8 DIN (PM9) Horizontal
15.75 mm
(0.62 in)
1.52 mm
(0.06 in)
100.33 mm
(3.95 in)
54.86 mm
(2.16 in)
53.34 mm
(2.10 in)
10.16 mm
(0.40 in)
30.73 mm
(1.21 in)
101.60 mm
(4.00 in)
1/8 DIN (PM9) Horizontal Recommended Panel Spacing
92.3 mm
(3.635 in)
45.2 mm
(1.78 in)
Panel thickness (0.060 in) 1.53 mm
to (0.375 in) 9.52 mm
21.6 mm
(0.85 in)
21.6 mm
(0.85 in)
Wat low EZ-ZONE ® PM PID Controller
•
10
•
Chapter 2 Install and Wire
1/4 DIN (PM4)
15.75
.62
100.33
3.95
1.52
.06
100.33
3.95
12.70
.50
30.73
1.21
100.84
3.97
1/4 DIN (PM4) Recommended Panel Spacing
92.3
3.635
92.3
3.635
21.6
.85
Panel thickness .060 (1.53) to .375 (9.52)
21.6
.85
Watlow EZ-ZONE ® PM PID Controller
•
11
•
Chapter 2 Install and Wire
Installation
Don't be afraid to apply enough pressure to properly install the controller. The seal system is
compressed more by mating the mounting collar
tighter to the front panel (see pictures above). If
you can move the case assembly back and forth
in the cutout, you do not have a proper seal.
The tabs on each side of the mounting collar have
teeth that latch into the ridges on the sides of the
controller. Each tooth is staggered at a different
depth from the front so that only one of the tabs,
on each side, is locked onto the ridges at a time.
panel
bezel
retention collar
gasket
case
Note:
There is a graduated measurement difference between the upper and lower half of the display to
the panel. In order to meet the seal requirements
mentioned above, ensure that the distance from the
front of the top half of the display to the panel is
16 mm (0.630 in.) or less, and the distance from the
front of the bottom half and the panel is 13.3 mm
(0.525 in.) or less.
panel
retention collar
bezel
gasket
case
Removing the Mounted Controller from Its Case
1. From the controller's face, pull out the tabs on
each side until you hear it click.
1. Make the panel cutout using the mounting template dimensions in this chapter.
Insert the case assembly into the panel cutout.
2. While pressing the case assembly firmly against
the panel, slide the mounting collar over the back
of the controller.
If the installation does not require a NEMA 4X
seal, simply slide together until the gasket is
compressed.
Pull out the tab on each side
until you hear it click.
Grab the unit above and
below the face and pull forward.
2. On a PM6 control once the sides are released
grab the unit above and below the face with two
hands and pull the unit out. On the PM4/8/9 controls slide a screwdriver under the pry tabs and
turn.
çWarning:
• This equipment is suitable for use in class 1, div.
2, Groups A, B, C and D or Non-Hazardous locations only. Temperature Code T4A.
Slide the mounting collar over Place the blade of a screwthe back of the controller.
driver in the notch of the
mounting collar assembly.
• WARNING – EXPLOSION HAZARD. Substitution of component may impair suitability for class
1, div. 2.
3. For a NEMA 4X (UL50, IP66) seal, alternately
place and push the blade of a screwdriver against
each of the the four corners of the mounting collar assembly. Apply pressure to the face of the
controller while pushing with the screwdriver.
Wat low EZ-ZONE ® PM PID Controller
•
• WARNING – EXPLOSION HAZARD. Do not
disconnect equipment unless power has been
switched off or the area is known to be nonhazardous.
12
•
Chapter 2 Install and Wire
Returning the Controller to its Case
1. Ensure that the orientation of the controller is
correct and slide it back into the housing.
Note: The controller is keyed so if it feels that it will not
slide back in do not force it. Check the orientation again
and reinsert after correcting.
2. Using your thumbs push on either side of the controller until both latches click.
Chemical Compatibility
This product is compatible with acids, weak alkalis,
alcohols, gamma radiation and ultraviolet radiation.
This product is not compatible with strong alkalis,
organic solvents, fuels, aromatic hydrocarbons, chlorinated hydrocarbons, esters and keytones.
çWarning:
All electrical power to the controller and controlled
circuits must be disconnected before removing the
controller from the front panel or disconnecting
other wiring.
Failure to follow these instructions may cause an
electrical shock and/or sparks that could cause an
explosion in class 1, div. 2 hazardous locations.
Watlow EZ-ZONE ® PM PID Controller
•
13
•
Chapter 2 Install and Wire
Wiring
Terminal Definitions for Slots A
Slot A
Output
Terminal Function
Configuration
common (Any switched dc output can use this common.)
dc- (open collector)
dc+
Switched dc/open collector
output 1: PM _ _ _ C _-_ AAAA _ _
dcdc+
Switched dc
output 2: PM _ _ _ _ C-_ AAAA _ _
F1
G1
H1
voltage or current voltage +
current +
Universal Process
output 1: PM _ _ _ F _-_ AAAA _ _
L1
K1
J1
normally open
common
normally closed
Mechanical Relay 5 A, Form C
output 1: PM _ _ _ E _-_ AAAA _ _
L2
K2
normally open
common
NO-ARC 15 A, Form A
output 2: PM[4, 6, 8, 9] _ _ _ H-_ AAAA _ _
L2
K2
normally open
common
Mechanical Relay 5 A, Form A
output 2: PM _ _ _ _ J-_ AAAA _ _
L2
K2
normally open
common
Solid-state Relay 0.5 A, Form A
output 1: PM _ _ _ K _-_ AAAA _ _
output 2: PM _ _ _ _ K-_ AAAA _ _
S2 (RTD) or current +
S3 (RTD), thermocouple -, current -, volts - or potentiometer wiper, thermistor
S1 (RTD), thermocouple + or volts +, thermistor
Universal / Thermistor Input
input 1: all configurations
1
2
X1
W1
Y1
W2
Y2
L1
K1
Inputs
1
T1
S1
R1
Slot A
Terminal Definitions for Slot C
Slot C
Terminal Function
Configuration
98
99
power input: ac or dc+
power input: ac or dc-
all
CC
CA
CB
Standard Bus or Modbus RTU EIA-485 common
Standard Bus or Modbus RTU EIA-485 T-/RStandard Bus or Modbus RTU EIA-485 T+/R+
Standard Bus or Modbus
PM _ _ _ _ _-1 AAAA _ _
CF
CD
CE
Standard Bus EIA-485 common
Standard Bus EIA-485 T-/RStandard Bus EIA-485 T+/R+
PM _ _ _ _ _-A AAAA _ _
B5
D6
D5
digital input-output common
digital input or output 6
digital input or output 5
PM _ _ 2 _ _-_ AAAA _ _
PM _ _ 4 _ _-_ AAAA _ _
Back View
Slot Orientation
1/16 DIN PM6
Back View
Slot Orientation
1/32 DIN PM3
Output 2
Input 1
A
B
C
Wat low EZ-ZONE ® PM PID Controller
485 Comms
Dig I/O 5 & 6
C
Dig I/O 5 & 6 485 Comms
Output 1
Power
Power
A
Output 1
•
14
•
Output 2
Input 1
Chapter 2 Install and Wire
Back View
Slot Orientation 1/8
DIN Vertical PM8
Power
A
C
E
D
B
Dig I/O 5 & 6 485 Comms
Dig I/O 5 & 6 485 Comms
C
Input 1
Input 1
E
Output 2
Output 2
A
Output 1
Output 1
Power
Back View
Slot Orientation
1/8 DIN Horizontal PM9
Input 1
A
D
E
C
Dig I/O 5 & 6 485 Comms
Communications Card
Output 2
Digital I/O 7 - 12
Output 1
D
B
Power
Back View
Slot Orientation
1/4 DIN Horizontal PM4
Output 3
Output 4
Input 2
B
EZ-ZONE PM Isolation Blocks
Mechanical Relay,
Solid-State Relay,
NO-ARC Relay
Outputs
Digital Inputs & Outputs
5-6
No Isolation
Switched DC, Open Collector,
Process outputs
No Isolation
Analog Input 1
Low-voltage
Isolation
Communications Ports
Safety Isolation
Safety Isolation
Controller Power Supply
12 to 40VÎ (dc)
20 to 28VÅ (ac)
100 to 240VÅ (ac)
No Isolation
Controller
Low Voltage Power Bus
Safety Isolation
Low-voltage Isolation: 42V peak
Safety Isolation: 2300VÅ (ac)
Watlow EZ-ZONE ® PM PID Controller
•
15
•
Chapter 2 Install and Wire
Óç
Warning:
Use National Electric (NEC)
or other country-specific
standard wiring and safety
practices when wiring and
connecting this controller to
a power source and to electrical sensors or peripheral
devices. Failure to do so may
result in damage to equipment and property, and/or
injury or loss of life.
Note:
Maximum wire size termination and torque rating:
• 0.0507 to 3.30 mm2 (30 to
12 AWG) single-wire termination or two 1.31 mm2 (16
AWG)
• 0.8 Nm (7.0 lb.-in.) torque
Note:
Adjacent terminals may be
labeled differently, depending on the model number.
Note:
To prevent damage to the
controller, do not connect
wires to unused terminals.
Low Power
Slot C
98
99
power
power
• Minimum/Maximum Ratings
• 12 to 40VÎ (dc)
• 20 to 28VÅ (ac) Semi Sig F47
• 47 to 63 Hz
• 14VA maximum power consumption (PM4,8 & 9)
• 10VA maximum power consumption (PM3 & 6)
PM_ _ [3,4] _ _ - _ _ _ _ _ _ _
CF
CD
CE
B5
D6
D5
Power
High Power
Slot C
98
99
power
power
fuse
CF
CD
CE
B5
D6
• Minimum/Maximum Ratings
• 85 to 264VÅ (ac)
• 100 to 240VÅ (ac) Semi Sig F47
• 47 to 63 Hz
• 14VA maximum power consumption (PM4,8 & 9)
• 10VA maximum power consumption (PM3 & 6)
PM_ _ [1,2] _ _ - _ _ _ _ _ _ _
D5
Power
Digital Input 5, 6
Voltage Input
Note:
Maintain electrical isolation
between analog input 1, digital input-outputs, switched
dc/open collector outputs and
process outputs to prevent
ground loops.
Note:
The control output common
terminal and the digital common terminal are referenced
to different voltages and
must remain isolated.
fuse
Slot C
98
CF
CD
CE
B5
DC Input
D6
DC Input
common
Vdc
DC Voltage
• Input not to exceed 36V at
3 mA
• Input active when > 3V @
0.25 mA
• Input inactive when < 2V
99
common
B_
Digital Input
• Update rate 10 Hz
• Dry contact or dc voltage
D_
Dry Contact
Dry Contact
• Input inactive when >
500 Ω
• Input active when < 100 Ω
• maximum short circuit 13
mA
PM_ _ [2,4] _ _-_ _ _ _ _ _ _
D5
B_
common
D_
24 Vdc
Wat low EZ-ZONE ® PM PID Controller
•
16
•
Chapter 2 Install and Wire
Óç
Warning:
Use National Electric (NEC)
or other country-specific
standard wiring and safety
practices when wiring and
connecting this controller to
a power source and to electrical sensors or peripheral
devices. Failure to do so may
result in damage to equipment and property, and/or
injury or loss of life.
Input 1 Thermocouple
Slot A
-
S1
+
R1
Input 1 RTD
Note:
Maximum wire size termination and torque rating:
• 0.0507 to 3.30 mm2 (30 to
12 AWG) single-wire termination or two 1.31 mm2 (16
AWG)
• 0.8 Nm (7.0 lb.-in.) torque
Note:
Adjacent terminals may be
labeled differently, depending on the model number.
Note:
To prevent damage to the
controller, do not connect
wires to unused terminals.
Slot A
Slot A
S2
T1
S3
S1
S3
S1
S1
R1
S1
R1
3-wire
2-wire
• platinum, 100 and 1,000 Ω @ 0°C
• calibration to DIN curve (0.00385 Ω/Ω/°C)
• 20 Ω total lead resistance
• RTD excitation current of 0.09 mA typical. Each
ohm of lead resistance may affect the reading by
0.03°C.
• For 3-wire RTDs, the S1 lead (usually white) must
be connected to R1.
• For best accuracy use a 3-wire RTD to compensate
for lead-length resistance. All three lead wires must
have the same resistance.
PM _ _ _ _ _-_ AAAA _ _
Input 1 Process
Slot A
Note:
Maintain electrical isolation
between analog input 1, digital input-outputs, switched
dc/open collector outputs and
process outputs to prevent
ground loops.
Note:
The control output common
terminal and the digital common terminal are referenced
to different voltages and
must remain isolated.
• 2 kΩ maximum source resistance
• >20 MΩ input impedance
• 3 microampere open-sensor detection
• Thermocouples are polarity sensitive. The negative lead (usually
red) must be connected to S1.
• To reduce errors, the extension wire for thermocouples must be
of the same alloy as the thermocouple.
PM _ _ _ _ _-_ AAAA _ _
Slot A
• 0 to 20 mA @ 100 Ω input impedance
• 0 to 10VÎ (dc) @ 20 kΩ input impedance
• 0 to 50 mVÎ (dc) @ 20 kΩ input impedance
• scalable
PM _ _ _ _ _-_ AAAA _ _
+ T1
-
- S1
+ R1
S1
amperes
volts
Input 1 Potentiometer
Slot A
• Use a 1 kΩ potentiometer.
PM _ _ _ _ _-_ AAAA _ _
CW
CCW
S1
R1
Watlow EZ-ZONE ® PM PID Controller
•
17
•
Chapter 2 Install and Wire
Óç
Input 1 Thermistor
Warning:
Use National Electric (NEC)
or other country-specific
standard wiring and safety
practices when wiring and
connecting this controller to
a power source and to electrical sensors or peripheral
devices. Failure to do so may
result in damage to equipment and property, and/or
injury or loss of life.
Slot A
• >20 MΩ input impedance
• 3 microampere open-sensor detection
Input 1: PM _ [J,N,E*] _ _ _ _-_ _ _ _ _ _ _ (S1/
R1)
*PM4,8 & 9 only
S1
R1
Note:
Maximum wire size termination and torque rating:
• 0.0507 to 3.30 mm2 (30 to
12 AWG) single-wire termination or two 1.31 mm2 (16
AWG)
• 0.8 Nm (7.0 lb.-in.) torque
Note:
Adjacent terminals may be
labeled differently, depending on the model number.
Note:
To prevent damage to the
controller, do not connect
wires to unused terminals.
Note:
Maintain electrical isolation
between analog input 1, digital input-outputs, switched
dc/open collector outputs and
process outputs to prevent
ground loops.
Note:
The control output common
terminal and the digital common terminal are referenced
to different voltages and
must remain isolated.
Wat low EZ-ZONE ® PM PID Controller
•
18
•
Chapter 2 Install and Wire
Óç
Digital Output 5, 6
Slot C
98
Warning:
Use National Electric (NEC)
or other country-specific
standard wiring and safety
practices when wiring and
connecting this controller to
a power source and to electrical sensors or peripheral
devices. Failure to do so may
result in damage to equipment and property, and/or
injury or loss of life.
Note:
Maximum wire size termination and torque rating:
• 0.0507 to 3.30 mm2 (30 to
12 AWG) single-wire termination or two 1.31 mm2 (16
AWG)
• 0.8 Nm (7.0 lb.-in.) torque
99
CF
CD
CE
B5
D6
Digital Output
• Update rate 10 Hz
• Output voltage 24V
• Current limit, Output 5, 24
mA maximum
• Current limit, Output 6,
10 mA maximum driving
single pole DIN-A-MITE
• Capable of driving a 3-pole
DIN-A-MITE
• Open-circuit voltage 22 to
32VÎ (dc)
PM _ _ [2,4] _ _-_ _ _ _ _ _ _
switched dc outputs
VDC
D5
D6
Internal Circuitry
B5
D5
Switched DC Wiring Example Using DO 5 and 6
switched dc outputs
Htr 1
VDC
Note:
Adjacent terminals may be
labeled differently, depending on the model number.
D5
Htr 2
+
+
-
D6
B5
Internal Circuitry
DC80-60C0-0000
Note:
To prevent damage to the
controller, do not connect
wires to unused terminals.
Note:
Maintain electrical isolation
between analog input 1, digital input-outputs, switched
dc/open collector outputs and
process outputs to prevent
ground loops.
Note:
The control output common
terminal and the digital common terminal are referenced
to different voltages and
must remain isolated.
Quencharc Note:
Switching pilot duty inductive
loads (relay coils, solenoids,
etc.) with the mechanical
relay, solid state relay or
open collector output options
requires use of an R.C. suppressor.
Watlow EZ-ZONE ® PM PID Controller
•
19
•
Chapter 2 Install and Wire
Óç
Warning:
Use National Electric (NEC)
or other country-specific
standard wiring and safety
practices when wiring and
connecting this controller to
a power source and to electrical sensors or peripheral
devices. Failure to do so may
result in damage to equipment and property, and/or
injury or loss of life.
Output 1 Switched DC/Open Collector
Slot A
common
dc - (open collector)
dc +
X1
W1
Y1
Open Collector
• 100 mA maximum output current sink
• 30VÎ (dc) maximum supply
voltage
• Any switched dc output can use
the common terminal.
• Use an external power supply to
control a dc load, with the load
positive to the positive of the
power supply, the load negative
to the open collector and common to the power supply negative.
See Quencharc note.
PM _ _ _ [C] _-_ AAAA _ _
Note:
Maximum wire size termination and torque rating:
• 0.0507 to 3.30 mm2 (30 to
12 AWG) single-wire termination or two 1.31 mm2 (16
AWG)
• 0.8 Nm (7.0 lb.-in.) torque
Note:
Adjacent terminals may be
labeled differently, depending on the model number.
Note:
To prevent damage to the
controller, do not connect
wires to unused terminals.
Quencharc Note:
Switching pilot duty inductive
loads (relay coils, solenoids,
etc.) with the mechanical
relay, solid state relay or
open collector output options
requires use of an R.C. suppressor.
Switched DC
X1
W1
common
dc -
24V
Y1
dc +
Open Collector
Power Supply
X1
W1
common
dc -
24V
Load
Y1
Output 1 Mechanical Relay, Form C
normally open
common
normally closed
Slot A
L1
K1
J1
Note:
Maintain electrical isolation
between analog input 1, digital input-outputs, switched
dc/open collector outputs and
process outputs to prevent
ground loops.
Note:
The control output common
terminal and the digital common terminal are referenced
to different voltages and
must remain isolated.
Switched DC
• 30 mA dc maximum supply current
• short circuit limited to <50 mA
• 22 to 32VÎ (dc) open circuit
voltage
• Use dc- and dc+ to drive external solid-state relay.
• DIN-A-MITE compatible
• single-pole: up to 4 in parallel or
4 in series
• 2-pole: up to 2 in parallel or 2 in
series
• 3-pole: up to 2 in series
• 5 A at 240VÅ (ac) or 30VÎ (dc)
maximum resistive load
• 20 mA at 24V minimum load
• 125 VA pilot duty at 120/240VÅ
(ac), 25 VA at 24VÅ (ac)
• 100,000 cycles at rated load
• Output does not supply power.
• for use with ac or dc
See Quencharc note.
PM _ _ _ [E] _-_ AAAA _ _
L1
normally open
K1
common
J1
normally closed
Output 1 Universal Process
Slot A
volts or current -
F1
volts +
G1
current +
H1
• 0 to 20 mA into 800 Ω maximum load
• 0 to 10VÎ (dc) into voltage 1
kΩ minimum load
• scalable
• output supplies power
• cannot use voltage and current
outputs at same time
• Output may be used as retransmit or control.
PM _ _ _ [F] _-_ AAAA _ _
F1
negative
0 to 10 V
4 to 20 mA
G1
volts +
H1
current +
Universal Process
(Output 1)
Wat low EZ-ZONE ® PM PID Controller
•
20
•
Chapter 2 Install and Wire
Óç
Warning:
Use National Electric (NEC)
or other country-specific
standard wiring and safety
practices when wiring and
connecting this controller to
a power source and to electrical sensors or peripheral
devices. Failure to do so may
result in damage to equipment and property, and/or
injury or loss of life.
Output 1 Solid-State Relay, Form A
Slot A
normally open
L1
common
K1
• 0.5 A at 20 to 264VÅ (ac) maximum resistive load
• 20 VA 120/240VÅ (ac) pilot duty
• opto-isolated, without contact
suppression
• maximum off state leakage of
105 microamperes
• output does not supply power
• Do not use on dc loads.
• See Quencharc note.
PM _ _ _ [K] _-_ AAAA _ _
L1
K1
1 Amp SSR Derating Curve
1.1
1
Note:
Maximum wire size termination and torque rating:
• 0.0507 to 3.30 mm2 (30 to
12 AWG) single-wire termination or two 1.31 mm2 (16
AWG)
• 0.8 Nm (7.0 lb.-in.) torque
0.9
Safe Operating Area
Amps RMS
0.8
0.7
0.6
0.5
0.4
0.3
0.2
0.1
0
Note:
Adjacent terminals may be
labeled differently, depending on the model number.
-20
10
20
30
40
Ambient Temperatue (oC)
50
60
70
Output 2 Switched DC
Note:
To prevent damage to the
controller, do not connect
wires to unused terminals.
Note:
Maintain electrical isolation
between analog input 1, digital input-outputs, switched
dc/open collector outputs and
process outputs to prevent
ground loops.
0
-10
Slot A
dcdc+
W2
Y2
• 10 mA dc maximum supply current
• short circuit limited to <50 mA
• 22 to 32VÎ (dc) open circuit voltage
• use dc- and dc+ to drive external
solid-state relay
• DIN-A-MITE compatible
• single-pole: up to 2 in series,
none in parallel
PM _ _ _ _ [C]-_ AAAA _ _
common
W2
dc -
24V
Y2
dc +
Note:
The control output common
terminal and the digital common terminal are referenced
to different voltages and
must remain isolated.
Quencharc Note:
Switching pilot duty inductive
loads (relay coils, solenoids,
etc.) with the mechanical
relay, solid state relay or
open collector output options
requires use of an R.C. suppressor.
Watlow EZ-ZONE ® PM PID Controller
•
21
•
Chapter 2 Install and Wire
Óç
Warning:
Use National Electric (NEC)
or other country-specific
standard wiring and safety
practices when wiring and
connecting this controller to
a power source and to electrical sensors or peripheral
devices. Failure to do so may
result in damage to equipment and property, and/or
injury or loss of life.
Note:
Maximum wire size termination and torque rating:
• 0.0507 to 3.30 mm2 (30 to
12 AWG) single-wire termination or two 1.31 mm2 (16
AWG)
• 0.8 Nm (7.0 lb.-in.) torque
Output 2 NO-ARC Relay, Form A
Slot A
normally open
common
• 15 A at 85 to 264VÅ (ac) resistive load only
• 1/16 DIN models only
• 2,000,000 cycle rating for NOARC circuit
• 100 mA minimum load
• 2 mA maximum off state leakage
• Do not use on dc loads.
• Output does not supply power.
PM [4, 6, 8, 9] _ _ _ [H]-_ AAAA
__
L2
K2
Note:
Maintain electrical isolation
between analog input 1, digital input-outputs, switched
dc/open collector outputs and
process outputs to prevent
ground loops.
Slot A
normally open
common
• 5 A at 240VÅ (ac) or 30VÎ (dc)
maximum resistive load
• 20 mA at 24V minimum load
• 125 VA pilot duty @ 120/240VÅ
(ac), 25 VA at 24VÅ (ac)
• 100,000 cycles at rated load
• Output does not supply power.
• for use with ac or dc
See Quencharc note.
PM _ _ _ _ [J]-_ AAAA _ _
L2
K2
L2
K2
Output 2 Solid-state Relay, Form A
Slot A
• 0.5 A at 20 to 264VÅ (ac) maximum resistive load
• 20 VA 120/240VÅ (ac) pilot duty
• opto-isolated, without contact
suppression
• maximum off state leakage of
105 microamperes
• Output does not supply power.
• Do not use on dc loads.
See Quencharc note.
PM _ _ _ _ [K]-_ AAAA _ _
L1
K1
J1
normally open
L2
common
K2
T1
S1
R1
Solid-state Relay
(Ouput 2)
L2
K2
1 Amp SSR Derating Curve
1.1
1
0.9
0.8
Safe Operating Area
Amps RMS
Note:
The control output common
terminal and the digital common terminal are referenced
to different voltages and
must remain isolated.
K2
Output 2 Mechanical Relay, Form A
Note:
Adjacent terminals may be
labeled differently, depending on the model number.
Note:
To prevent damage to the
controller, do not connect
wires to unused terminals.
L2
0.7
0.6
0.5
0.4
0.3
0.2
0.1
0
-20
Wat low EZ-ZONE ® PM PID Controller
•
0
-10
22
•
10
20
30
40
Ambient Temperatue (oC)
50
60
70
Chapter 2 Install and Wire
Óç
Warning:
Use National Electric (NEC)
or other country-specific
standard wiring and safety
practices when wiring and
connecting this controller to
a power source and to electrical sensors or peripheral
devices. Failure to do so may
result in damage to equipment and property, and/or
injury or loss of life.
Quencharc Wiring Example
In this example the Quencharc circuit (Watlow
part# 0804-0147-0000) is used to protect PM
internal circuitry from the counter electromagnetic force from the inductive user load
when de-engergized. It is recommended that
this or an equivalent Quencharc be used when
connecting inductive loads to PM outputs.
98
99
CF common
CD
CE
T-/RT+/R+
B5
D6
Note:
Avoid continuous writes
within loops. Excessive
writes to EEPROM will cause
premature EEPROM failure.
The EEPROM is rated for
1,000,000 writes.
• Do not connect more than 16
EZ-ZONE PM controllers on a
network.
• maximum network length:
1,200 meters (4,000 feet)
• 1/8th unit load on EIA-485 bus
PM _ _ _ _ _-[A] AAAA _ _
D5
Standard Bus
EIA-485
Modbus RTU or Standard Bus EIA-485 Communications
Slot C
Note:
To prevent damage to the
controller, do not connect
wires to unused terminals.
Note:
The control output common
terminal and the digital common terminal are referenced
to different voltages and
must remain isolated.
K_
• Wire T-/R- to the A terminal of
the EIA-485 port.
• Wire T+/R+ to the B terminal of
the EIA-485 port.
• Wire common to the common
terminal of the EIA-485 port.
• Do not route network wires
with power wires. Connect network wires in daisy-chain fashion when connecting multiple
devices in a network.
Slot C
98
Note:
Maintain electrical isolation
between analog input 1, digital input-outputs, switched
dc/open collector outputs and
process outputs to prevent
ground loops.
N
Quencharc
Standard Bus EIA-485 Communications
Note:
Maximum wire size termination and torque rating:
• 0.0507 to 3.30 mm2 (30 to
12 AWG) single-wire termination or two 1.31 mm2 (16
AWG)
• 0.8 Nm (7.0 lb.-in.) torque
Note:
Adjacent terminals may be
labeled differently, depending on the model number.
User Load
L_
99
CC common
CA
CB
T-/RT+/R+
B5
D6
D5
• Wire T-/R- to the A terminal of
the EIA-485 port.
• Wire T+/R+ to the B terminal of
the EIA-485 port.
• Wire common to the common
terminal of the EIA-485 port.
• Do not route network wires
with power wires. Connect network wires in daisy-chain fashion when connecting multiple
devices in a network.
• A termination resistor may be
required. Place a 120 Ω resistor
across T+/R+ and T-/R- of last
controller on network.
• Only one protocol per port is
available at a time: either Modbus RTU or Standard Bus.
• Do not connect more than 16
EZ-ZONE PM controllers on a
Standard Bus network.
• Do not connect more than 247
EZ-ZONE PM controllers on a
Modbus RTU network.
• maximum network length:
1,200 meters (4,000 feet)
• 1/8th unit load on EIA-485 bus.
PM _ _ _ _ _-[1] AAAA _ _
Modbus RTU or
Standard Bus EIA-485
Modbus-IDA
Terminal
EIA/TIA-485
Name
Watlow Terminal Label
Function
DO
A
CA or CD
T-/R-
D1
B
CB or CE
T+/R+
common
common
CC or CF
common
Wiring a Serial EIA-485 Network
Two example networks are shown below where the first one is using Watlow's Standard Bus and the other showing connections over Modbus. Do not
route network wires with power wires. Connect network wires in daisy-chain
fashion when connecting multiple devices in a network. A termination resistor may be required. Place a 120 Ω resistor across T+/R+ and T-/R- of the last
controller on a network. Only one protocol per port is available at a time: either Modbus RTU or Standard Bus.
Watlow EZ-ZONE ® PM PID Controller
•
23
•
Chapter 2 Install and Wire
Warning:
Use National Electric (NEC)
or other country-specific
standard wiring and safety
practices when wiring and
connecting this controller to
a power source and to electrical sensors or peripheral
devices. Failure to do so may
result in damage to equipment and property, and/or
injury or loss of life.
98
99
CF
CE
CD
B5
-A
+B
99
EZ-ZONE PM
power
com
-A
CD
+B
CE
CF
B5
Slot C
D6
CZ
CX
CY
CE
99
CD
98
CF
D5
power
RUI/Gateway
EZKB-_ A _ _- _ _ _ _
98
power
common
-A
CD
+B
99
common
-A
+B
CF
CE
A Network Using Modbus RTU.
Power
Supply
EZ-ZONE ST
ST_ _ - (B or F) _ M _ -_ _ _ _
EZ-ZONE RM
fuse
98
99
CC
98
99
EZ-ZONE PM
PM_ _ _ _ _-1AAAAXX
CC
CA
CB
power
power
com
-A
+B
B5
Slot C
D6
CY
CZ
CX
CA
98
D5
CB
-A
+B
power
power
common
99
CA
B5
CB
D6
Note:
The control output common
terminal and the digital common terminal are referenced
to different voltages and
must remain isolated.
power
power
common
98
D5
Note:
Maintain electrical isolation
between analog input 1, digital input-outputs, switched
dc/open collector outputs and
process outputs to prevent
ground loops.
D6
D5
Note:
To prevent damage to the
controller, do not connect
wires to unused terminals.
EZ-ZONE RM
fuse
Note:
Maximum wire size termination and torque rating:
• 0.0507 to 3.30 mm2 (30 to
12 AWG) single-wire termination or two 1.31 mm2 (16
AWG)
• 0.8 Nm (7.0 lb.-in.) torque
Note:
Adjacent terminals may be
labeled differently, depending on the model number.
Power
Supply
EZ-ZONE ST
ST_ _ - (B or F) _ M _ -_ _ _ _
CC
Óç
A Network Using Watlow's Standard Bus and an RUI/Gateway
power
power
power
common
-A
+B
PLC
Wat low EZ-ZONE ® PM PID Controller
•
24
•
common
-A
+B
Chapter 2 Install and Wire
Óç
Connecting a Computer to PM Controls Using B&B 485 to USB Converter
Warning:
Use National Electric (NEC)
or other country-specific
standard wiring and safety
practices when wiring and
connecting this controller to
a power source and to electrical sensors or peripheral
devices. Failure to do so may
result in damage to equipment and property, and/or
injury or loss of life.
Note:
Maximum wire size termination and torque rating:
• 0.0507 to 3.30 mm2 (30 to
12 AWG) single-wire termination or two 1.31 mm2 (16
AWG)
• 0.8 Nm (7.0 lb.-in.) torque
Note:
Adjacent terminals may be
labeled differently, depending on the model number.
Note:
To prevent damage to the
controller, do not connect
wires to unused terminals.
Note:
Maintain electrical isolation
between analog input 1, digital input-outputs, switched
dc/open collector outputs and
process outputs to prevent
ground loops.
Note:
The control output common
terminal and the digital common terminal are referenced
to different voltages and
must remain isolated.
Watlow EZ-ZONE ® PM PID Controller
•
25
•
Chapter 2 Install and Wire
3
Chapter 3: Keys and Displays
Upper (Left, 32nd DIN) Display:
1/32 DIN (PM3)
In the Home Page, displays the process
value, otherwise displays the value of
the parameter in the lower display.
Zone Display:
Indicates the controller zone.
®
1 2
1/16 DIN (PM6)
A = zone 10
b = zone 11
C = zone 12
d = zone 13
E = zone 14
F = zone 15
h = zone 16
Percent Units:
Profile Activity:
EZ Key/s:
1/8 DIN (PM9) Horizontal
Lights when the controller is displaying values as a percentage or
when the open-loop set point is
displayed.
Channel Display:
Indicates the set point or output
power value during operation, or
the parameter whose value appears in the upper display.
Lights when a profile is running.
Flashes when a profile is paused.
®
1 to 9 = zones 1 to 9
Lower (Right, 32nd DIN) Display:
This key can be programmed to do
various tasks, such as locking the
keyboard, restoring user settings,
etc...
®
Output Activity:
Number LEDs indicate activity of
outputs. A flashing light indicates
output activity.
1/8 DIN (PM8) Vertical
Indicates the channel for any given
EZ-ZONE module.
Communications Activity
Flashes when another device is
communicating with this controller.
®
- Available with the PM4, 8 and PM9 only.
Temperature Units:
Indicates whether the temperature is displayed in Fahrenheit or
Celsius.
Infinity Key ˆ
Press to back up one level, or press and
hold for two seconds to return to the
Home Page. From the Home Page can
clear alarms and errors if clearable.
Up and Down Keys ¿ ¯
1/4 DIN (PM4)
®
In the Home Page, adjusts the set
point in the lower display. In other
pages, changes the upper display to a higher or lower value, or
changes a parameter selection.
Advance Key ‰
Advances through parameter prompts.
Wat low EZ-ZONE ® PM PID Controller
•
26
•
Chapter 3 Keys and Displays
Responding to a Displayed Message
An active message will cause the display to toggle between the normal settings and the active message in
the upper display and [Attn] in the lower display.
Your response will depend on the message and the
controller settings. Some messages, such as Ramping
and Tuning, indicate that a process is underway. If
the message was generated by a latched alarm and
the condition no longer exists or if an alarm has si-
Display
[Attn]
lencing enabled it can be silenced simply by pushing
the Infinity ˆ key. Alternatively, use the method below to view all and then clear.
Push the Advance Key to display [ignr] in the upper display and the message source (such as [al;h1])
in the lower display.Use the Up ¿ or Down ¯ keys
to scroll through possible responses, such as Clear
[`CLr] or Silence [`SiL]. Then push the Advance ‰
or Infinity ˆ key to execute the action. See the Home
Page for further information on the Attention Codes.
Parameter Name
Description
Range
Attention
An active message will cause
the display to toggle between
the normal settings and the
active message in the upper
display and [Attn] in the
lower display.
Your response will depend on
the message and the controller settings. Some messages,
such as Ramping and Tuning, indicate that a process is
underway. If the message was
generated by a latched alarm
or limit condition, the message
can be cleared when the condition no longer exists. If an
alarm has silencing enabled, it
can be silenced.
Push the Advance Key to display [ignr] in the upper display and the message source
(such as [Li;h1]) in the lower
display.
Use the Up ¿ or Down ¯ keys
to scroll through possible responses, such as Clear [`CLr]
or Silence [`SiL]. Then push
the Advance ‰ or Infinity
ˆ key to execute the action.
Alternatively, rather than
scrolling through all messages
simply push the Infinity ˆ
button to generate a clear.
Watlow EZ-ZONE ® PM PID Controller
•
Appears If
[AL;L1] [AL;L2] [AL;L3]
[AL;L4] Alarm Low 1 to 4
[AL;h1] [AL;h2] [AL;h3]
[AL;h4] Alarm High 1 to 4
[AL;E1] [AL;E2] [AL;E3]
[AL;E4] Alarm Error 1 to 4
[Er;i1] Error Input 1
[tUn1] Tuning 1
[`rP1] Ramping 1
[LP;o1] Loop Open Error 1
[LP;r1] Loop Reversed Error 1
27
•
an alarm or error message is
active.
Chapter 3 Keys and Displays
4
Chapter 4: Home Page
Default Home Page Parameters
Watlow’s patented user-defined menu system improves operational efficiency. The user-defined Home
Page provides you with a shortcut to monitor or
change the parameter values that you use most often. The default Home Page is shown on the following page. When a parameter normally located in the
Setup Page or Operations Page is placed in the Home
Page, it is accessible through both. If you change
a parameter in the Home Page, it is automatically
changed in its original page. If you change a parameter in its original page it is automatically changed
in the Home Page.
The Attention [Attn] parameter appears only if
there is an active message. An example of an active
message could be an Input Error [er;i1], or it could
be for information only like Autotune [tUN1] taking
place.
Use the Advance Key ‰to step through the other
parameters. When not in pairs the parameter prompt
will appear in the lower display, and the parameter
value will appear in the upper display. You can use
the Up ¿ and Down ¯ keys to change the value of
writable parameters, just as you would in any other
menu.
If Control Mode is set to Auto, the Process Value
is in the upper display and the Closed Loop Set Point
(read-write) is in the lower display.
If a profile is running, the process value is in the
upper display and the Target Set Point (read only) is
in the lower display. If Control Mode is set to Manual, the Process Value is in the upper display and the
output power level (read-write) is in the lower display.
If Control Mode is set to Off, the Process Value is
in the upper display and [`oFF] (read only) is in the
lower display.
If a sensor failure has occurred, [----] is in the
upper display and the output power level (read-write)
is in the lower display.
Active Process Value [aC; p u] will be displayed on top
and Parameter [`par] in the bottom. Using the Up
¿ or Down ¯ arrow keys will allow for a customized selection of choice. There are twenty positions
available that can be customized.
Modifying the Display Pairs
The Home Page, being a customized list of as many
as 20 parameters can be configured in pairs of up to
10 via the Display Pairs [d;prs] prompt found in the
Diagnostic Menu [diag] (Factory Page). The listing
in the table that follows is what one may typically
find in the Home Page as defaults based on controller part numbers. It is important to note that some
of the prompts shown may not appear simply because
the feature is not being used or is turned off. As an
example, the prompt Cool Power [C; p r1] will not appear unless the Cool algorithm [`C; a g ] is turned on
in the Setup Page under the Loop menu. The Display
Pairs [d;prs] prompt will default to 1, therefore the
upper display will reflect the Active Process Value
[aC;pu] and the lower display will reflect the Active
Set Point [aC;sp] by default.
As stated above, the user can define pairs of
prompts to appear on the display every time the Advance ‰ key is pushed. When configuring the Custom Menu to your liking it should be noted that if
2 changeable (writable) prompts are displayed in a
Pair, i.e., Control Mode on top and Idle Set Point on
the bottom, only the lower display (Idle Set Point)
can be changed.
The display can be configured to scroll by going to the Factory Page under the Diagnostic Menu
and changing the Display Time [`d ; ti] prompt to
something greater than 0. If set to 2, the display will
scroll every 2 seconds from one Display Pair to another. If the Display Pair prompt [d;prs] is set to 1
the Display Time [`d ; ti] prompt will have no effect
on the display.
Changing the Set Point
You can change the set point by using the Up ¿ or
Down ¯ keys when a profile is not running.
Modifying the Home Page
To modify the Home Page proceed to the Factory
Menu by pushing and holding the Advance ‰ key
and the Infinity ˆ key for approximately six seconds.
Upon entering the Factory Page the first menu will
be the Custom Menu [Cust] . Once there push the
Advance ‰ key where the lower display will show
[Cust] and the upper display will show [1] . Again,
push the Advance ‰ button where the prompt for the
Watlow EZ-ZONE ® PM PID Controller
•
28
•
Chapter 4 Home Page
Home Page Defaults
Home Page
Display
Parameter Page and Menu
All Models
1
Active Process Value (1)
Numerical
value
Operations Page, Monitor Menu
2
Active Set Point (1)
Numerical
value
Operations Page, Monitor Menu
3
User Control Mode (1)
[C;M1]
Operations Page, Monitor Menu
4
Heat Power (1)
[h;pr1]
Operations Page, Monitor Menu
5
Cool Power (1)
[C;pr1]
Operations Page, Monitor Menu
6
Autotune (1)
[aut1]
Operations Page, Loop Menu
7
Idle (1)
[id;s1]
Operations Page, Loop Menu
8
* Start Profile
[p;st1]
9
* Action Request
[p;aC1]
10 None
11 None
12 None
13 None
14 None
15 None
16 None
17 None
18 None
19 None
20 None
* The fourth digit of the part number must be:
PM _ [R, B, N or E] _ _ _ - _ _ _ _ _ _ _
Watlow EZ-ZONE ® PM PID Controller
•
29
•
Chapter 4 Home Page
Navigating the EZ-ZONE® PM PID Controller
Applies to All Models - 1/16 DIN Shown Below
®
®
®
®
[``Ai]
[``70]
[``70]
[Cust]
[`Set]
[``72]
[``72]
[fCty]
Home Page from anywhere: Press the Infinity
Factory Page from Home Page: Press both the
Advance ‰ and Infinity ˆ keys for six seconds.
Key ˆ for two seconds to return to the Home Page.
®
®
[``70]
[``Ai]
[``72]
[oper]
Operations Page from Home Page: Press both
the Up ¿ and Down ¯ keys for three seconds.
®
®
[``70]
[``Ai]
[``72]
[`Set]
Setup Page from Home Page: Press both the
Up ¿ and Down ¯ keys for six seconds.
®
®
[``70]
[``p1]
[``72]
[prof]
Profiling Page from Home Page: Press the
Advance Key ‰ for three seconds.
Watlow EZ-ZONE ® PM PID Controller
•
30
•
Chapter 4 Home Page
Display
Conventions Used in the Menu Pages
To better understand the menu pages that follow
review the naming conventions used. When encountered throughout this document, the word "default"
implies as shipped from the factory. Each page (Operations, Setup, Profile and Factory) and their associated menus have identical headers defined below:
Header Name
Visual information from the control is displayed to
the observer using a fairly standard 7 segment display. Due to the use of this technology, several characters displayed need some interpretation, see the
list below:
Definition
[1] = 1
[0] = 0
[i] = i
[r] = r
[2] = 2
[a] = A
[j ] = J
[S] = S
Display
Visually displayed information from the control.
[3] = 3
[ b] = b
[H] = K
[ t] = t
[4] = 4
[c] , [C] = c
[l] = L
[U] = u
Parameter Name
Describes the function of
the given parameter.
[5] = 5
[d ] = d
[m] = M
[u] = v
[6] = 6
[ e] = E
[n] = n
[w] = W
[7] = 7
[ f] = F
[o] = o
[y ] = y
Range
Defines options available
for this prompt, i.e., min/
max values (numerical),
yes/no, etc... (further explanation below).
[8] = 8
[g ] = g
[ p] = P
[2] = Z
[9] = 9
[ h] = h
[q ] = q
Default
Values as delivered from
the factory.
Modbus Relative Address
Identifies unique parameters using either the
Modbus RTU or Modbus
TCP protocols (further explanation below).
CIP (Common Industrial Protocol)
Identifies unique parameters using either the DeviceNet or EtherNet/IP
protocol (further explanation below).
Profibus Index
Identifies unique parameters using Profibus DP
protocol (further explanation below).
Parameter ID
Identifies unique parameters used with other software such as, LabVIEW.
Range
Within this column notice that on occasion there will
be numbers found within parenthesis. This number
represents the enumerated value for that particular
selection. Range selections can be made simply by
writing the enumerated value of choice using any of
the available communications protocols. As an example, turn to the Setup Page and look at the Analog
Input [`Ai] menu and then the Sensor Type [Sen]
prompt. To turn the sensor off simply write the value
of 62 (off) to Modbus register 400369 and send that
value to the control.
Modbus RTU Protocols
All Modbus registers are 16-bits and as displayed
in this manual are relative addresses (actual). Some
legacy software packages limit available Modbus registers to 40001 to 49999 (5 digits). Many applications
today require access to all available Modbus registers which range from 400001 to 465535 (6 digits).
Watlow controls support 6 digit Modbus registers.
For parameters listed as float notice that only one
(low order) of the two registers is listed, this is true
throughout this document. By default the low order
word contains the two low bytes of the 32-bit parameter. As an example, look in the Operations Page for
the Process Value. Find the column identified in the
header as Modbus and notice that it lists register
360. Because this parameter is a float it is actually
represented by registers 360 (low order bytes) and
361 (high order bytes). Because the Modbus specification does not dictate which register should be high
or low order Watlow provides the user the ability to
swap this order (Setup Page, Com Menu) from the
default low/high [lohi] to high/low [ hilo] .
uint = Unsigned 16 bit integer
dint
= long, 32-bit
string = ASCII (8 bits per character)
Data Type R/W
float =IEEE 754 32-bit
RWES=Readable
Writable
EEPROM (saved)
User Set (saved)
Note:
With the release of firmware revision 7.00 and
above new functions where introduced into this
product line. With the introduction of these new
functions there was a reorganization of Modbus
registers. Notice in the column identified as ModWatlow EZ-ZONE ® PM PID Controller
•
31
•
Chapter 4 Home Page
bus the reference to Map 1 and Map 2 registers for
each of the various parameters. If the new functions, namely; Linearization, Process Value and
Real Time Clock are to be used than use Map 2
Modbus registers. The Data Map [map] for Modbus registers can be changed in the Setup Page under the [Com] Menu. This setting will apply across
the control.
It should also be noted that some of the cells in the
Modbus column contain wording pertaining to an offset. Several parameters in the control contain more
than one instance; such as, profiles (4), alarms (4),
analog inputs (2), etc... The Modbus register shown
always represents instance one. Take for an example
the Alarm Silence parameter found in the Setup
Page under the Alarm menu. Instance one of Map 1
is shown as address 1490 and +50 is identified as the
offset to the next instance. If there was a desire to
read or write to instance 3 simply add 100 to 1490 to
find its address, in this case, the instance 3 address
for Alarm Silence is 1590.
To learn more about the Modbus protocol point
your browser to http://www.modbus.org.
Note:
There are two columns shown in the menus that
follow for communications protocols identified as
CIP (Common Industrial Protocol) and Profibus.
These columns will be useful if this control is used
in conjunction with the EZ-ZONE Remote User Interface/Gateway (RUI/GTW) where those protocols
can be selected as optional hardware. For this control, as a secondary protocol beyond Standard Bus,
Modbus RTU can be ordered as optional hardware.
To learn more about the RUI/GTW point your
browser to the link below and search for keyword
EZ-ZONE.
http://www.watlow.com/literature/pti_search.cfm
Watlow EZ-ZONE ® PM PID Controller
•
32
•
Chapter 4 Home Page
5
Chapter 5: Operations Page
Navigating the Operations Page
To go to the Operations Page from the Home Page,
press both the Up ¿ and Down ¯ keys for three seconds. [``Ai] will appear in the upper display and
[oPEr] will appear in the lower display.
• Press the Up ¿ or Down ¯ key to view available
menus. On the following pages top level menus are
identified with a yellow background color.
• Press the Advance Key ‰ to enter the menu of
choice.
• If a submenu exists (more than one instance), press
the Up ¿ or Down ¯ key to select and then press
the Advance Key ‰ to enter.
• Press the Up ¿ or Down ¯ key to move through
available menu prompts.
• Press the Infinity Key ˆ to move backwards
through the levels: parameter to submenu; submenu to menu; menu to Home Page.
• Press and hold the Infinity Key ˆ for two seconds
to return to the Home Page.
Note:
Some of these menus and parameters may not appear, depending on the controller's options. See model
number information in the Appendix for more information. If there is only one instance of a menu, no submenus will appear.
Operations Page
[``Ai]
[oPEr] Analog Input Menu
[`Ain] Process Value
[`i;Er] Error Status
[`i;Ca] Calibration Offset
[`Lnr]*
[oPEr] Linearization Menu
[`Su;A] Source Value A
[oFSt] Offset
[``o;u] Output Value
[``Pu]*
[oPEr] Process Value Menu
[`Su;A] Source Value A
[oFSt] Offset
[``o;u] Output Value
[`dio]
[oPEr] Digital Input/Output Menu
[```5] to [``6]
[`dio] Digital Input/Output
[`do;S] Output State
[`ei;S] Event State
[`di;S] Input State
[Mon]
[oPEr] Monitor Menu
[C;MA] Control Mode Active
[`h;Pr] Heat Power
[`C;Pr] Cool Power
[`C;SP] Closed Loop Working Set Point
[`Pu;A] Process Value Active
[Loop]
[oPEr] Loop Menu
[`r;En] Remote Enable
[`C;M] Control Mode
[A;tSP] Autotune Set Point
[`AUt] Autotune Request
[`C;SP] Closed Loop Set Point
[`id;S] Idle Set Point
[`h;Pb] Heat Proportional Band
[`h;hy] Heat Hysteresis
[`C;Pb] Cool Proportional Band
[`C;hy] Cool Hysteresis
[``ti] Time Integral
[``td] Time Derivative
[``db] Dead Band
[`o;SP] Open Loop Set Point
[ALM]
[oPEr] Alarm Menu
[```1] to [```4]
[ALM] Alarm 1
[`A;Lo] Low Set Point
[`A;hi] High Set Point
P;StA]
[oPEr] Profile Status Menu [```1] to [```4]
[P;StA] Profile Status
[P;Str] Profile Start
[PACr] Action Request
[`StP] Active Step
[S;tyP] Active Step Type
[t;SP1] Target Set Point Loop 1
[AC;SP] Produced Set Point 1
[hour] Hours Remaining
[min] Minutes Remaining
[`seC] Seconds Remaining
[Ent1] Active Event Output 1
[Ent2] Active Event Output 2
[``JC] Jump Count Remaining
* Available with PM4, PM8 and PM9 models only
Watlow EZ-ZONE ® PM PID Controller
•
33
•
Chapter 5 Operations Page
Operations Page
Display
Parameter Name
Description
Range
Default
Modbus Relative Address
CIP
Class
Instance
Attribute
hex (dec)
Profibus
Index
Paqrameter ID
Data
Type
&
Read/
Write
[``Ai]
[oPEr]
Analog Input Menu
Instance 1
Map 1 Map 2
360
360
Instance 2
Map 1 Map 2
440
450
0x68 (104)
1
1
0
4001
float
R
None
[nonE] None (61)
[OPEn] Open (65)
[FAiL] Fail (32)
[Shrt] Shorted (127)
[`E;M] Measurement
Error (140)
[E;CAL] Bad Calibration
Data (139)
[Er;Ab] Ambient Error (9)
[E;;Rtd] RTD Error (141)
[Nsrc] Not Sourced
(246)
Instance 1
Map 1 Map 2
362
362
Instance 2
Map 1 Map 2
442
452
0x68 (104)
1
2
1
4002
uint
R
-1,999.000 to
9,999.000°F or units
-1,110.555 to
5,555.000°C
0.0
Instance 1
Map 1 Map 2
382
382
Instance 2
Map 1 Map 2
462
472
0x68 (104)
1
0xC (12)
2
4012
float
RWES
[`Ain]
[ Ain]
Analog Input (1)
Process Value
View the process value.
-1,999.000 to
9,999.000°F or units
-1,128.000 to
5,537.000°C
[`i;Er]
[ i.Er]
Analog Input (1)
Error Status
View the cause of the most
recent error. If the [Attn]
message is [Er;i1] or
[Er;i2], this parameter
will display the cause of the
input error.
[`i;Ca]
[ i.CA]
Analog Input (1)
Calibration Offset
Offset the input reading to
compensate for lead wire
resistance or other factors
that cause the input reading to vary from the actual
process value.
----
[`Lnr]*
[oPEr]
Linearization Menu
[`Su;A]
[ Su.A]
Linearization (1)
Source Value A
View the value of Source
A.
Source A of Linearization
1 is connected to Analog
Input 1
-1,999.000 to
9,999.000°F or units
-1,128.000 to
5,537.000°C
----
Instance 1
Map 1 Map 2
- - - -
3566
0x86 (134)
1
4
----
34004
float
R
[oFSt]
[oFSt]
Linearization (1)
Offset
Set an offset to be applied
to this function's output.
-1,999.000 to
9,999.000°F or units
-1,128.000 to
5,537.000°C
0
Instance 1
Map 1 Map 2
- - - -
3570
0x86 (134)
1
6
----
34006
float
RWES
[``o;u]
[ o.v]
Linearization (1)
Output Value
View the value of this
function's output.
-1,999.000 to
9,999.000°F or units
-1,128.000 to
5,537.000°C
----
Instance 1
Map 1 Map 2
- - - -
3572
0x86 (134)
1
7
----
34007
float
R
Note:
Some values will be rounded off to fit in the four-character display. Full values can be read with other interfaces.
* Available with PM4, PM8 and PM9 models only
Watlow EZ-ZONE ® PM PID Controller
•
34
•
R: Read
W: Write
E: EEPROM
S: User
Set
Chapter 5 Operations Page
Operations Page
Display
No Display
Parameter Name
Description
Linearization (1)
Output Error
View reported cause for
Linearization output malfunction.
Range
Modbus Relative Address
CIP
Class
Instance
Attribute
hex (dec)
----
Instance 1
Map 1 Map 2
- - - -
3614
----
Paqrameter ID
0x86 (134)
1
0x1C (28)
----
34028
uint
R
Instance 1
Map 1 Map 2
- - - -
3310
0x7E (126)
1
0x10 (16)
----
26016
float
R
Instance 1
Map 1 Map 2
- - - -
3324
0x7E (126)
1
0x17 (23)
----
26023
float
RWES
----
Instance 1
Map 1 Map 2
- - - -
3322
0x7E (126)
1
0x16 (22)
----
26022
float
R
----
Instance 1
Map 1 Map 2
- - - -
3332
0x86 (134)
1 to 2
0x1B (27)
----
26027
uint
R
Default
None (61)
Open (65)
Shorted (127)
Measurement error
(140)
Bad calibration data
(139)
Ambient error (9)
RTD error (14)
Fail (32)
Math error (1423)
Not sourced (246)
Stale (1617)
Can't process (1659)
Data
Type
&
Read/
Write
Profibus
Index
[``Pu]*
[oPEr]
Process Value Menu
[`Su;A]
[ Sv.A]
Process Value (1)
-1,999.000 to
Source Value A
9,999.000°F or units
View the value of Source A. -1,128.000 to
Linearization 1 is connect5,537.000°C
ed to Source A of Process
Value 1
[oFSt]
[oFSt]
Process Value (1)
Offset
Set an offset to be applied
to this function's output.
[``o;u]
[ o.v]
Process Value (1)
-1,999.000 to
Output Value
9,999.000°F or units
View the value of this func- -1,128.000 to
tion block's output.
5,537.000°C
No Display
Process Value (1)
Output Error
View reported cause for
Process output malfunction.
-1,999.000 to
9,999.000°F or units
-1,128.000 to
5,537.000°C
0
None (61)
Open (65)
Shorted (127)
Measurement error
(140)
Bad calibration data
(139)
Ambient error (9)
RTD error (14)
Fail (32)
Math error (1423)
Not sourced (246)
Stale (1617)
Can't process (1659)
Note:
Some values will be rounded off to fit in the four-character display. Full values can be read with other interfaces.
* Available with PM4, PM8 and PM9 models only
Watlow EZ-ZONE ® PM PID Controller
•
35
•
R: Read
W: Write
E: EEPROM
S: User
Set
Chapter 5 Operations Page
Operations Page
Display
Parameter Name
Description
Range
Default
Modbus Relative Address
CIP
Class
Instance
Attribute
hex (dec)
Profibus
Index
Paqrameter ID
Data
Type
&
Read/
Write
[`dio]
[oPEr]
Digital Input/Output Menu
----
Instance 1
Map 1 Map 2
1012
1132
Offset to next
instance equals
+30
0x6A (106)
1 to 2
7
90
6007
uint
R
Digital Input (5 to 6)
[`iact] Inactive (41)
Event Status
[``act] Active (5)
View this event input state.
----
Instance 1
Map 1 Map 2
1328
1568
Offset to next
instance equals
+20
0x6E (110)
1 to 2
5
140
10005
uint
R
EZ-Key/s (1 to 2)
[`iact] Inactive (41)
Event Status
[``act] Active (5)
View this event input state.
----
Instance 1
Map 1 Map 2
1368
1608
Instance 2
Map 1 Map 2
- - - - 1628
0x6E (110)
3 to 4
5
140
10005
uint
R
[`do;S]
[ do.S]
Digital Output (5 to 6)
Output State
View the state of this output.
[`ei;S]
[ Ei.S]
No Display
[`off] Off (62)
[``on] On (63)
[Mon]
[oPEr]
Monitor Menu
[C;MA]
[C.MA]
Monitor (1)
Control Mode Active
View the current control
mode.
[`off] Off (62)
[AUto] Auto (10)
[MAn] Manual (54)
Off
Instance 1
Map 1 Map 2
1882
2362
0x97 (151)
1
2
----
8002
uint
R
[`h;Pr]
[ h.Pr]
Monitor (1)
Heat Power
View the current heat output level.
0.0 to 100.0%
0.0
Instance 1
Map 1 Map 2
1904
2384
0x97 (151)
1
0xD (13)
----
8011
float
R
[`C;Pr]
[ C.Pr]
Monitor (1)
Cool Power
View the current cool output level.
-100.0 to 0.0%
0.0
Instance 1
Map 1 Map 2
1906
2386
0x97 (151)
1
0xE (14)
----
8014
float
R
[`C;SP]
[ C.SP]
Monitor (1)
-1,999.000 to
Closed Loop Working Set 9,999.000°F or units
Point
-1,128.000 to
View the set point cur5,537.000°C
rently in effect.
----
Instance 1
Map 1 Map 2
2172
2652
0x6B (107)
1
7
----
8029
float
R
[`Pu;A]
[ Pv.A]
Monitor (1)
Process Value Active
View the current filtered
process value using the
control input.
-1,999.000 to
9,999.000°F or units
-1,128.000 to
5,537.000°C
----
Instance 1
Map 1 Map 2
402
402
0x68 (104)
1
0x16 (22)
----
8031
float
R
No Display
Monitor (1)
-1,999.000 to
Set Point Active
9,999.000°F or units
Read the current active set -1,128.000 to
point.
5,537.000°C
Instance 1
Map 1 Map 2
2172
2652
0x6B (107)
1
7
----
7018
float
R
Note:
Some values will be rounded off to fit in the four-character display. Full values can be read with other interfaces.
* Available with PM4, PM8 and PM9 models only
Watlow EZ-ZONE ® PM PID Controller
•
36
•
R: Read
W: Write
E: EEPROM
S: User
Set
Chapter 5 Operations Page
Operations Page
Display
Parameter Name
Description
Range
Default
Modbus Relative Address
CIP
Class
Instance
Attribute
hex (dec)
Profibus
Index
Paqrameter ID
Data
Type
&
Read/
Write
[Loop]
[oPEr]
Control Loop Menu
[`r;En]
[ r.En]
Control Loop (1)
Remote Enable
Enable this loop to switch
control to the remote set
point.
[``no] No
[`YES] Yes
No
Instance 1
Map 1 Map 2
2200
2680
0x6B (107)
1
0x15 (21)
48
7021
uint
RWES
[`r;ty]
[ r.ty]
Control Loop (1)
Remote Set Point Type
Enable this loop to switch
control to the remote set
point.
[auto] Auto (10)
[man] Manual (54)
No
Instance 1
Map 1 Map 2
2202
2682
0x6B (107)
1
0x16 (22)
----
7022
uint
RWES
[`C;M]
[ C.M]
Control Loop (1)
Control Mode
Select the method that
this loop will use to control.
[`off] Off (62)
[AUto] Auto (10)
[MAn] Manual (54)
Auto
Instance 1
Map 1 Map 2
1880
2360
0x97 (151)
1
1
63
8001
uint
RWES
[A;tSP]
[A.tSP}
Control Loop (1)
Autotune Set Point
Set the set point that the
autotune will use, as a
percentage of the current
set point.
50.0 to 200.0%
90.0
Instance 1
Map 1 Map 2
1998
2398
0x97 (151)
1
0x14 (20)
----
8025
float
RWES
[`AUt]
[ AUt]
Control Loop (1)
Autotune Request
Start an autotune. While
the autotune is active, the
Home Page will display
[Attn] [tUn1]. When the
autotune is complete, the
message will clear automatically.
[``no] No (59)
[`YES] Yes (106)
No
Instance 1
Map 1 Map 2
1920
2400
0x97 (151)
1
0x15 (21)
64
8026
uint
RW
[`C;SP]
[ C.SP]
Control Loop (1)
Closed Loop Set Point
Set the set point that the
controller will automatically control to.
Low Set Point to High
Set Point (Setup
Page)
75.0°F
or
units
24.0°C
Instance 1
Map 1 Map 2
2160
2640
0x6B (107)
1
1
49
7001
float
RWES
[`id;S]
[ id.S]
Control Loop (1)
Idle Set Point
Set a closed loop set point
that can be triggered by
an event state.
Low Set Point to High
Set Point (Setup
Page)
75.0°F
or
units
24.0°C
Instance 1
Map 1 Map 2
2176
2656
0x6B (107)
1
9
50
7009
float
RWES
[`h;Pb]
[ h.Pb]
Control Loop (1)
Heat Proportional Band
Set the PID proportional
band for the heat outputs.
0.001 to 9,999.000°F or
units
-1,110.555 to
5,555.000°C
25.0°F
or
units
14.0°C
Instance 1
Map 1 Map 2
1890
2370
0x97 (151)
1
6
65
8009
float
RWES
[`h;hy]
[ h.hy]
Control Loop (1)
Heat Hysteresis
Set the control switching
hysteresis for on-off control. This determines how
far into the “on” region
the process value needs
to move before the output
turns on.
0.001 to 9,999.000°F or
units
-1,110.555 to
5,555.000°C
3.0°F or
units
2.0°C
Instance 1
Map 1 Map 2
1900
2380
0x97 (151)
1
0xB (11)
66
8010
float
RWES
Note:
Some values will be rounded off to fit in the four-character display. Full values can be read with other interfaces.
* Available with PM4, PM8 and PM9 models only
Watlow EZ-ZONE ® PM PID Controller
•
37
•
R: Read
W: Write
E: EEPROM
S: User
Set
Chapter 5 Operations Page
Operations Page
Default
Modbus Relative Address
CIP
Class
Instance
Attribute
hex (dec)
0.001 to 9,999.000°F or
units
-1,110.555 to
5,555.000°C
25.0°F
or
units
14.0°C
Instance 1
Map 1 Map 2
1892
2370
Control Loop (1)
Cool Hysteresis
Set the control switching
hysteresis for on-off control. This determines how
far into the “on” region
the process value needs
to move before the output
turns on.
0.001 to 9,999.000°F or
units
-1,110.555 to
5,555.000°C
3.0°F or
units
2.0°C
[``ti]
[ ti]
Control Loop (1)
Time Integral
Set the PID integral for
the outputs.
[``td]
[ td]
Data
Type
&
Read/
Write
Profibus
Index
Paqrameter ID
0x97 (151)
1
7
67
8012
float
RWES
Instance 1
Map 1 Map 2
1902
2382
0x97 (151)
1
0xC (12)
68
8013
float
RWES
0 to 9,999 seconds per
repeat
180.0
Instance 1
seconds Map 1 Map 2
per re- 1894
2374
peat
0x97 (151)
1
8
69
8006
float
RWES
Control Loop (1)
Time Derivative
Set the PID derivative
time for the outputs.
0 to 9,999 seconds
0.0
Instance 1
seconds Map 1 Map 2
1896
2376
0x97 (151)
1
9
70
8007
float
RWES
[``dB]
[ db]
Control Loop (1)
Dead Band
Set the offset to the
proportional band. With
a negative value, both
heating and cooling outputs are active when the
process value is near the
set point. A positive value
keeps heating and cooling
outputs from fighting each
other.
-1,000.0 to 1,000.0°F
or units
-556 to 556°C
0.0
Instance 1
Map 1 Map 2
1898
2378
0x97 (151)
1
0xA (10)
71
8008
float
RWES
[`o;SP]
[ o.SP]
Control Loop (1)
Open Loop Set Point
Set a fixed level of output
power when in manual
(open-loop) mode.
-100 to 100% (heat and
cool)
0 to 100% (heat only)
-100 to 0% (cool only)
0.0
Instance 1
Map 1 Map 2
2162
2642
0x6B (107)
1
2
51
7002
float
RWES
No Display
Control Loop (1)
Loop Error
Open Loop detect deviation has been exceeded.
None (61)
Open Loop (1274)
Reversed Sensor (1275)
----
Instance 1
Map 1 Map 2
- - - -
1798
0x6C (108)
1
0x30 (48)
----
8030
uint
R
No Display
Control Loop (1)
Clear Loop Error
Current state of limit
output.
Clear (129)
Ignore (204)
----
Instance 1
Map 1 Map 2
- - - -
1800
0x6C (108)
1
0x31 (49)
----
8031
uint
W
Parameter Name
Description
Range
[`C;Pb]
[ C.Pb]
Control Loop (1)
Cool Proportional Band
Set the PID proportional
band for the cool outputs.
[`C;hy]
[ C.hy]
Display
Note:
Some values will be rounded off to fit in the four-character display. Full values can be read with other interfaces.
* Available with PM4, PM8 and PM9 models only
Watlow EZ-ZONE ® PM PID Controller
•
38
•
R: Read
W: Write
E: EEPROM
S: User
Set
Chapter 5 Operations Page
Operations Page
Parameter Name
Description
Display
Range
Default
Modbus Relative Address
CIP
Class
Instance
Attribute
hex (dec)
32.0°F
or
units
0.0°C
Instance 1
Map 1 Map 2
1482
1882
Data
Type
&
Read/
Write
Profibus
Index
Paqrameter ID
0x6D
(109)
1 to 4
2
18
9002
float
RWES
0x6D
(109)
1 to 4
1
19
9001
float
RWES
0x6D
(109)
1 to 4
9
----
9009
uint
R
0x6D
(109)
1 to 4
0xC (12)
----
9012
uint
R
[ALM]
[oPEr]
Alarm Menu
[`A;Lo]
[ A.Lo]
[`A;hi]
[ A.hi]
No Displayed
No Displayed
Alarm (1 to 4)
Low Set Point
If Alarm Type (Setup
Page, Alarm Menu) is
set to:
process - set the process
value that will trigger a
low alarm.
deviation - set the span of
units from the closed loop
set point that will trigger
a low alarm. A negative
set point represents a
value below closed loop
set point. A positive set
point represents a value
above closed loop set
point.
-1,999.000 to
9,999.000°F or units
-1,128.000 to
5,537.000°C
Alarm (1 to 4)
High Set Point
If Alarm Type (Setup
Page, Alarm Menu) is
set to:
process - set the process
value that will trigger a
high alarm.
deviation - set the span of
units from the closed loop
set point that will trigger
a high alarm.
-1,999.000 to
9,999.000°F or units
-1,128.000 to
5,537.000°C
Alarm (1 to 4)
Alarm State
Current state of alarm
Startup (88)
None (61)
Blocked (12)
Alarm low (8)
Alarm high (7)
Error (28)
Alarm (1 to 4)
Alarm Clearable
Current state of alarm
Offset to next
instance (Map
1) equals +50
Offset to next
instance (Map
2) equals +60
300.0°F
or
units
150.0°C
Instance 1
Map 1 Map 2
1480
1880
Offset to next
instance (Map
1) equals +50
Offset to next
instance (Map
2) equals +60
Instance 1
Map 1 Map 2
1496
1896
None
Offset to next
instance [Map1
+50], [Map 2
+60]
No (59)
Yes (106)
----
Instance 1
Map 1 Map 2
1502
1902
Offset to next
instance (Map1
1 equals +50,
Map 2 equals
+60)
Note:
Some values will be rounded off to fit in the four-character display. Full values can be read with other interfaces.
* Available with PM4, PM8 and PM9 models only
Watlow EZ-ZONE ® PM PID Controller
•
39
•
R: Read
W: Write
E: EEPROM
S: User
Set
Chapter 5 Operations Page
Operations Page
Display
No Displayed
Parameter Name
Description
Alarm (1 to 4)
Alarm Clear Request
Write to this register to
clear an alarm
Range
Default
Clear (1003)
0
Modbus Relative Address
CIP
Class
Instance
Attribute
hex (dec)
Instance 1
Map 1 Map 2
1504
1904
Data
Type
&
Read/
Write
Profibus
Index
Paqrameter ID
0x6D
(109)
1 to 4
0xD (13)
----
9013
uint
W
0x6D
(109)
1 to 4
0xE (14)
----
9014
uint
W
0x6D
(109)
1 to 4
0x0B (11)
----
9011
uint
R
0x6D
(109)
1 to 4
0x0A (10)
----
9010
uint
R
Offset to next
instance (Map1
1 equals +50,
Map 2 equals
+60)
No Displayed
Alarm (1 to 4)
Alarm Silence Request
Write to this register to
silence an alarm
Silence (1010)
Instance 1
Map 1 Map 2
1506
1906
0
Offset to next
instance (Map1
1 equals +50,
Map 2 equals
+60)
No Displayed
Alarm (1 to 4)
Alarm Silenced
Write to this register to
silence an alarm
Yes (106)
No (59)
----
Instance 1
Map 1 Map 2
1500
1900
Offset to next
instance (Map1
1 equals +50,
Map 2 equals
+60)
No Displayed
Alarm (1 to 4)
Alarm Latched
Write to this register to
silence an alarm
Yes (106)
No (59)
----
Instance 1
Map 1 Map 2
1498
1898
Offset to next
instance (Map1
1 equals +50,
Map 2 equals
+60)
* Available with PM8/9 only
*Some parameters in the Profile Status Menu can be changed for the
currently running profile, but should only be changed by knowledgeable personnel and with caution. Changing parameters via the Profile Status Menu will not change the stored profile but will have an
immediate impact on the profile that is running.
Changes made to profile parameters in the Profiling Pages will be
saved and will also have an immediate impact on the running profile.
[P;Sta]
[oPEr]
Profile Status Menu
Profile Menu appears if:
(PM _ [R, B*, N, E*] _ _ _-_ _ _ _ _ _ _)
[P;Str]
[P.Str]
Profile Status
Profile Start
Select step to act upon.
1 to 40
Instance 1
Map 1 Map 2
2520
4340
1
Note:
Some values will be rounded off to fit in the four-character display. Full values can be read with other interfaces.
* Available with PM4, PM8 and PM9 models only
Watlow EZ-ZONE ® PM PID Controller
•
40
•
0x7A (122)
1
1
204
22001
uint
RW
R: Read
W: Write
E: EEPROM
S: User
Set
Chapter 5 Operations Page
Operations Page
Display
Parameter Name
Description
Range
Default
Modbus Relative Address
CIP
Class
Instance
Attribute
hex (dec)
Profibus
Index
Paqrameter ID
Data
Type
&
Read/
Write
[P;ACr]
[PACr]
Profile Status
Action Request
[nonE] None (61)
[step] Step Start (89)
[`End] Terminate
(148)
[rESU] Resume (147)
[PAUS] Pause (146)
[ProF] Profile (77)
None
Instance 1
Map 1 Map 2
2540
4360
0x7A (122)
1
0xB (11)
205
22011
uint
RW
[`StP]
[ StP]
Profile Status
Active Step
View the currently running step.
1 to 40
0 (none)
Instance 1
Map 1 Map 2
2526
4346
0x7A (122)
1
4
----
22004
uint
R
[S;typ]
[S.typ]
Profile Status
Active Step Type
View the currently running step type.
UStP] Unused Step
(50)
[`End] End (27)
[``JL] Jump Loop
(116)
[CloC] Wait For Time
(1543)
[W;bo] Wait For Both
(210)
[W;Pr] Wait For Process (209)
[`W;E] Wait For Event
(144)
[SoAH] Soak (87)
[``ti] Time (143)
[rAtE] Rate (81)
----
Instance 1
Map 1 Map 2
2544
4364
0x7A (122)
1
0xD (13)
----
22013
uint
R
[t;SP1]
[tg.SP]
Profile Status
*Target Set Point Loop 1
View or change the target
set point of the current
step.
-1,999.000 to
9,999.000°F or units
-1,128.000 to
5,537.000°C
0.0°F
or
units
-18.0°C
Instance 1
Map 1 Map 2
2542
4502
0x7A (122)
1
0xC (12)
----
22012
uint
RW
[aC;sp]
[AC.SP]
Profile Status
Produced Set Point 1
Display the current set
point, even if the profile is
ramping.
-1,999.000 to
9,999.000°F or units
-1,128.000 to
5,537.000°C
0.0°F
or
units
-18.0°C
Instance 1
Map 1 Map 2
- - - -
----
----
----
22005
float
R
[hoUr]
[hoUr]
Profile Status
Hours
Step time remaing in
hours.
0 to 99
0
Instance 1
Map 1 Map 2
- - - -
4494
0x7A (122)
1
0x4E (78)
----
22078
uint
RW
[min]
[ Min]
Profile Status
Minutes
Step time remaing in
minutes.
0 to 59
0
Instance 1
Map 1 Map 2
- - - -
4492
0x7A (122)
1
0x4D (77)
----
22077
uint
RW
[`seC]
[ SEC]
Profile Status
Seconds
Step time remaing in
seconds.
0 to 59
0
Instance 1
Map 1 Map 2
- - - -
4490
0x7A (122)
1
0x4C (76)
----
22076
uint
RW
[Ent1]
[Ent1]
Profile Status
Active Event Output 1
View or change the event
output states.
[`off] Off (62)
[``on] On (63)
Off
Instance 1
Map 1 Map 2
2546
4512
0x7A (122)
1
0xE (14)
----
22014
uint
RW
Note:
Some values will be rounded off to fit in the four-character display. Full values can be read with other interfaces.
* Available with PM4, PM8 and PM9 models only
Watlow EZ-ZONE ® PM PID Controller
•
41
•
R: Read
W: Write
E: EEPROM
S: User
Set
Chapter 5 Operations Page
Operations Page
Display
Parameter Name
Description
Range
Default
Modbus Relative Address
CIP
Class
Instance
Attribute
hex (dec)
Profibus
Index
Paqrameter ID
Data
Type
&
Read/
Write
[Ent2]
[Ent2]
Profile Status
Active Event Output 2
View or change the event
output states.
[`off] Off (62)
[``on] On (63)
Off
Instance 1
Map 1 Map 2
2548
4514
0x7A (122)
1
0xF (15)
----
22015
uint
RW
[``JC]
[ JC]
Profile Status
Jump Count Remaining
View the jump counts
remaining for the current
loop. In a profile with
nested loops, this may not
indicate the actual jump
counts remaining.
0 to 9,999
0
Instance 1
Map 1 Map 2
2538
4358
0x7A (122)
1
0xA (10)
----
22010
uint
R
No Display
Profile Status
Profile State
Read currentProfile state.
off (62)
Running (149)
Pause (146)
Instance 1
Map 1 Map 2
2522
4342
0x7A (122)
1
2
----
22002
uint
R
No Display
Profile Status
Current File
Indicates current file being executed.
Instance 1
Map 1 Map 2
2524
4344
0x7A (122)
1
3
----
22003
uint
R
----
1 to 4
0
Note:
Some values will be rounded off to fit in the four-character display. Full values can be read with other interfaces.
* Available with PM4, PM8 and PM9 models only
Watlow EZ-ZONE ® PM PID Controller
•
42
•
R: Read
W: Write
E: EEPROM
S: User
Set
Chapter 5 Operations Page
6
Chapter 6: Setup Page
Navigating the Setup Page
To go to the Setup Page from the Home Page, press
both the Up ¿ and Down ¯ keys for six seconds.
[``Ai] will appear in the upper display and [`Set]
will appear in the lower display.
• Press the Up ¿ or Down ¯ key to view available
menus. On the following pages top level menus
are identified with a yellow background color.
•Press the Advance Key ‰ to enter the menu of
choice.
• If a submenu exists (more than one instance),
press the Up ¿ or Down ¯ key to select and then
press the Advance Key ‰ to enter.
• Press the Up ¿ or Down ¯ key to move through
available menu prompts.
• Press the Infinity Key ˆ to move backwards
through the levels: parameter to submenu; submenu to menu; menu to Home Page.
• Press and hold the Infinity Key ˆ for two seconds
to return to the Home Page.
Note:
Some of these menus and parameters may not appear, depending on the controller's options. See model
number information in the Appendix for more information. If there is only one instance of a menu, no submenus will appear.
[``Ai]
[`Set] Analog Input Menu
[`SEn] Sensor Type
[`Lin] Linearization
[`rt;L] RTD Leads
[Unit] Units
[`S;Lo] Scale Low
[`S;hi] Scale High
[`r;Lo] Range Low
[`r;hi] Range High
[`P;EE] Process Error Enable
[`P;EL] Process Error Low
[``t;C] Thermistor Curve
[``r;r] Resistance Range
[`FiL] Filter
[`i;er] Error Latching
[`dEC] Display Precision
[`Lnr]*
[`Set] Linearization Menu
[``Fn] Function
[Unit] Units
[`ip;1] Input Point 1
[`op;1] Output Point 1
[`ip;2] Input Point 2
[`op;2] Output Point 2
[`ip;3] Input Point 3
[`op;3] Output Point 3
[`ip;4] Input Point 4
[`op;4] Output Point 4
[`ip;5] Input Point 5
[`op;5] Output Point 5
[`ip;6] Input Point 6
[`op;6] Output Point 6
[`ip;7] Input Point 7
[`op;7] Output Point 7
[`ip;8] Input Point 8
[`op;8] Output Point 8
[`ip;9] Input Point 9
[`op;9] Output Point 9
[ip;10] Input Point 10
[op;10] Output Point 10
[SP;hi] Set Point Open Limit High
[``Pu]*
[`Set] Process Value
[``Fn] Function
[P;unt] Pressure Units
[A;unt] Altitude Units
[[`FiL] Filter
[otpt]
[`Set] Output Menu
[```1] to [```2]
[otpt] Output
[``Fn] Function
[``Fi] Function Instance
[`o;Ct] Control
[`o;tb] Time Base
[`o;Lo] Low Power Scale
[`o;hi] High Power Scale
[otpt] Output 1 process
[`o;ty] Type
[``Fn] Function
[``Fi] Function Instance
[`S;Lo] Scale Low
[`S;hi] Scale High
[`r;Lo] Range Low
[`r;hi] Range High
[`o;lo] Power Scale Low
[`o;ho] Power Scale High
[`o;CA] Calibration Offset
[`dio]
[`Set] Digital Input/Output Menu
[```5] to [```6]
[`dio] Digital Input/Output
[`dir] Direction
[``Fn] Function
[``Fi] Function Instance
[`o;Ct] Control
[`o;tb] Time Base
[`o;Lo] Low Power Scale
[`o;hi] High Power Scale
[[Loop]
[`Set] Control Loop Menu
[`h;Ag] Heat Algorithm
[`C;Ag] Cool Algorithm
[`C;Cr] Cool Output Curve
[t;tUn] Tru-Tune+™ Enable
[t;bnd] Tru-Tune+™ Band
[`t;gn] Tru-Tune+™ Gain
[t;Agr] Autotune Aggressiveness
[`P;dl] Peltier Delay
[`UFA] User Failure Action
[FAiL] Input Error Failure
[MAn] Manual Power
[`L;dE] Open Loop Detect Enable
[`L;dt] Open Loop Detect Time
[`L;dd] Open Loop Detect Deviation
[``rp] Ramp Action
[`r;SC] Ramp Scale
[`r;rt] Ramp Rate
[`L;SP] Low Set Point
[`h;SP] High Set Point
[SP;Lo] Set Point Open Limit Low
[ALM]
[`Set] Alarm Menu
[```1] to [```4]
[ALM] Alarm
[`A;ty] Type
[`sr;a] Source Function A
[`A;hy] Hysteresis
[`a;Lg] Logic
[`A;SD] Sides
[`a;LA] Latching
[`A;bL] Blocking
[`a;Si] Silencing
[A;dsp] Display
[`A;dL] Delay
[`fUn]
[`Set] Function Key Menu
[```1] to [```2]
[`fUn] Function Key
* Available with PM4, PM8 and PM9 models only
Watlow EZ-ZONE ® PM PID Controller
•
43
•
Chapter 6 Setup Page
[`leu] Level
[``Fn] Digital Input Function
[``fi] Instance
[gLbL]
[`Set] Global Menu
[`C_F] Display Units
[AC;LF] AC Line Frequency
[r;typ] Ramping Type
[p;typ] Profile type
[`gse] Guaranteed Soak Enable
[gsd1] Guaranteed Soak Deviation 1
[`si;a] Source instance A
[`si;b] Source instance B
[poti] Power Out Time
[C;led] Communications LED Action
[2one] Zone Action
[Chan] Channel Action
[d;prs] Display Pairs
[`d;ti] Menu Display Timer
[Usr;s] User Save
[Usr;r] User Restore
[COM]
[`Set] Communications Menu [pCol] Protocol
[`a;ds] Standard Bus Address
[ad;m] Modbus Address
[bAUd] Baud Rate
[`PAr] Parity
[M;hL] Modbus Word Order
[map] Data Map
[`C_f] Display Units
[`nu;s] Non-volatile Save
[`rtC]*
[`Set] Real Time Clock Menu
[hoUr] Hour
[min] Minute
[dow] Day of Week
* Available with PM8 and PM9 models only
Watlow EZ-ZONE ® PM PID Controller
•
44
•
Chapter 6 Setup Page
Setup Page
Display
Parameter Name
Description
Range
Default
CIP
Modbus RelaClass
tive
Instance
Address
Attribute
hex (dec)
Profibus
Index
Parameter ID
Data
Type
&
Read/
Write
[``Ai]
[`Set]
Analog Input Menu
[`Sen]
[ SEn]
Analog Input (1)
Sensor Type
Set the analog sensor type
to match the device wired
to this input.
Note:
There is no open-sensor detection for process inputs.
[`oFF] Off (62)
[``tC] Thermocouple (95)
[`mu] Millivolts (56)
[uolT] Volts dc (104)
[`MA] Milliamps dc (112)
[r0;1H] RTD 100 Ω (113)
[r1;0H] RTD 1,000 Ω (114)
[`Pot] Potentiometer 1
kΩ (155)
[thEr] Thermistor (229)
Instance 1
0x68 (104)
1
Map 1 Map 2
5
368
368
3
4005
uint
RWES
[```b] B (11) [```H] K (48) J
[```C] C (15) [```n] N (58)
[```d] D (23) [```r] R (80)
[```E] E (26) [```S] S (84)
[```F] F (30) [```t] T (93)
[```J] J (46)
Instance 1
0x68 (104)
1
Map 1 Map 2
6
370
370
4
4006
uint
RWES
2
Instance 1
0x68 (104)
1
Map 1 Map 2
7
372
368
----
4007
uint
RWES
Instance 1
0x68 (104)
1
Map 1 Map 2
----
442 0x2A (42)
5
4042
uint
RWES
0.0
Instance 1
0x68 (104)
1
Map 1 Map 2
0xF (15)
388 388
6
4015
float
RWES
20.0
Instance 1
0x68 (104)
1
Map 1 Map 2
0x10 (16)
390 390
7
4016
float
RWES
0.0
Instance 1
0x68 (104)
1
Map 1 Map 2
0x11
(17)
392 392
8
4017
float
RWES
[`Lin]
[ Lin]
Analog Input (1)
Linearization
Set the linearization to
match the thermocouple
wired to this input.
[`Rt;L]
[ rt.L]
Analog Input (1)
[```2] 2 (1)
RTD Leads
[```3] 3 (2)
Set to match the number
of leads on the RTD wired
to this input.
[Unit]
[Unit]
Analog Input (1)
Units
Set the type of units the
sensor will measure.
[`S;Lo]
[ S.Lo]
Analog Input (1)
Scale Low
Set the low scale for process inputs. This value,
in millivolts, volts or milliamps, will correspond to
the Range Low output of
this function block.
[`S;hi]
[ S.hi]
Analog Input (1)
-100.0 to 1,000.0
Scale High
Set the high scale for
process inputs. This value,
in millivolts, volts or milliamps, will correspond to
the Range High output of
this function block.
[`r;Lo]
[ r.Lo]
Analog Input (1)
Range Low
Set the low range for this
function block's output.
[`A;tP] Absolute Tempera- Process
ture (1540)
[``rh] Relative Humidity
(1538)
[`Pro] Process (75)
[PWr] Power (73)
-100.0 to 1,000.0
-1,999.000 to 9,999.000
Note:
Some values will be rounded off to fit in the four-character display. Full values can be read with other interfaces.
* Available with PM4, PM8 and PM9 models only
Watlow EZ-ZONE ® PM PID Controller
•
45
•
R: Read
W: Write
E: EEPROM
S: User
Set
Chapter 6 Setup Page
Setup Page
Display
Parameter Name
Description
Range
Default
CIP
Modbus RelaClass
tive
Instance
Address
Attribute
hex (dec)
Profibus
Index
Parameter ID
Data
Type
&
Read/
Write
[`r;hi]
[ r.hi]
Analog Input (1)
-1,999.000 to 9,999.000
Range High
Set the high range for this
function block's output.
9,999
Instance 1
0x68 (104)
1
Map 1 Map 2
0x12 (18)
394 394
9
4018
float
RWES
[`P;EE]
[ P.EE]
Analog Input (1)
Process Error Enable
Turn the Process Error
Low feature on or off.
[`off] Off (62)
[Low] Low (53)
Off
Instance 1
0x68 (104)
1
Map 1 Map 2
418 388 0x1E (30)
10
4030
uint
RWES
[`P;EL]
[ P.EL]
Analog Input (1)
Process Error Low
If the process value drops
below this value, it will
trigger an input error.
-100.0 to 1,000.0
0.0
Instance 1
0x68 (104)
1
Map 1 Map 2
420 420 0x1F (31)
11
4031
float
RWES
[``t;C]
[ t.C]
Analog Input (1)
Thermistor Curve
Select a curve to apply to
the thermistor input.
[```A]
[```b]
[```C]
[CUSt]
Curve A (1451)
Curve B (1452)
Curve C (1453)
Custom (180)
Curve A
Instance 1
0x68 (104)
1
Map 1 Map 2
20x6 (38)
434 434
----
4038
uint
RWES
[``r;r]
[ r.r]
Analog Input (1)
Resistance Range
Set the maximum resistance of the thermistor
input.
[```5]
[``10]
[``20]
[``40]
5K (1448)
10K (1360)
20K (1361)
40K (1449)
40K
Instance 1
0x68 (104)
1
Map 1 Map 2
0x25 (37)
432 432
----
4037
uint
RWES
[`FiL]
[ FiL]
Analog Input (1)
0.0 to 60.0 seconds
Filter
Filtering smooths out the
process signal to both the
display and the input.
Increase the time to increase filtering.
0.5
Instance 1
0x68 (104)
1
Map 1 Map 2
0xE (14)
386
386
12
4014
float
RWES
[`i;Er]
[ i.Er]
Analog Input (1)
[`off] Off (62)
Error Latching
[``on] On (63)
Turn input error latching
on or off. If latching is on,
errors must be manually
cleared.
Off
Instance 1
0x68 (104)
1
Map 1 Map 2
414 414 0x1C (28)
----
4028
uint
RWES
[`dEC]
[ dEC]
Analog Input (1)
Display Precision
Set the precision of the
displayed value.
Whole
Instance 1
0x68 (104)
Map 1 Map 2
1
398 398
0x14 (20)
----
4020
uint
RWES
Instance 1
0x86 (134)
1
Map 1 Map 2
5
- - - -
3568
155
34005
uint
RWES
[```0] Whole (105)
[``0;0] Tenths (94)
[`0;00] Hundredths (40)
[0;000] Thousandths (96)
[`Lnr]*
[`Set]
Linearization Menu
[``Fn]
[ Fn]
Linearization (1)
Off
[`oFF] Off (62)
Function
[intr] Interpolated (1482)
Set how this function will
linearize Source A which
is Analog Input 1.
Note:
Some values will be rounded off to fit in the four-character display. Full values can be read with other interfaces.
* Available with PM4, PM8 and PM9 models only
Watlow EZ-ZONE ® PM PID Controller
•
46
•
R: Read
W: Write
E: EEPROM
S: User
Set
Chapter 6 Setup Page
Setup Page
Display
Parameter Name
Description
Range
Default
CIP
Modbus RelaClass
tive
Instance
Address
Attribute
hex (dec)
Profibus
Index
Parameter ID
Data
Type
&
Read/
Write
[Unit]
[Unit]
Linearization (1)
Units
Set the units of Source A
which is Analog Input 1.
Source
[nonE] None (61)
[`Src] Source (1539)
[``rh] Relative Humidty
(1538)
[`pro] Process (75)
[PWr] Power (73)
[`r;tp] Relative Temperature (1541)
[`A;tP] Absolute Temperature (1540)
Instance 1
0x86 (134)
1
Map 1 Map 2
----
3616 0x29 (41)
156
34029
uint
RWES
[`iP;1]
[ ip.1]
Linearization (1)
Input Point 1
Set the value that will be
mapped to output 1.
-1,999.000 to 9,999.000
0.0
Instance 1
0x86 (134)
1
Map 1 Map 2
8
- - - -
3574
157
34008
float
RWES
[`oP;1]
[ op.1]
Linearization (1)
Output Point 1
Set the value that will be
mapped to input 1.
-1,999.000 to 9,999.000
0.0
Instance 1
0x86 (134)
1
Map 1 Map 2
- - - -
3594 0x12 (18)
158
34018
float
RWES
[`iP;2]
[ ip.2]
Linearization (1)
Input Point 2
Set the value that will be
mapped to output 2.
-1,999.000 to 9,999.000
1.0
Instance 1
0x86 (134)
1
Map 1 Map 2
9
----
3576
159
34009
float
RWES
[`oP;2]
[ op.2]
Linearization (1)
Output Point 2
Set the value that will be
mapped to input 2.
-1,999.000 to 9,999.000
1.0
Instance 1
0x86 (134)
1
Map 1 Map 2
----
3597 0x13 (19)
160
34019
float
RWES
[`iP;3]
[ ip.3]
Linearization (1)
Input Point 3
Set the value that will be
mapped to output 3.
-1,999.000 to 9,999.000
2.0
Instance 1
0x86 (134)
1
Map 1 Map 2
----
3578 0xA (10)
161
34010
float
RWES
[`oP;3]
[ op.3]
Linearization (1)
Output Point 3
Set the value that will be
mapped to input 3.
-1,999.000 to 9,999.000
2.0
Instance 1
0x86 (134)
1
Map 1 Map 2
----
3598 0x14 (20)
162
34020
float
RWES
[`iP;4]
[ ip.4]
Linearization (1)
Input Point 4
Set the value that will be
mapped to output 4.
-1,999.000 to 9,999.000
3.0
Instance 1
0x86 (134)
1
Map 1 Map 2
----
3581 0xB (11)
163
34011
float
RWES
[`oP;4]
[ op.4]
Linearization (1)
Output Point 4
Set the value that will be
mapped to input 4.
-1,999.000 to 9,999.000
3.0
Instance 1
0x86 (134)
1
Map 1 Map 2
0x15
(21)
- - - -
3600
164
34021
float
RWES
[`iP;5]
[ ip.5]
Linearization (1)
Input Point 5
Set the value that will be
mapped to output 5.
-1,999.000 to 9,999.000
4.0
Instance 1
0x86 (134)
1
Map 1 Map 2
- - - -
3582 0xC (12)
165
34012
float
RWES
[`oP;5]
[ op.5]
Linearization (1)
Output Point 5
Set the value that will be
mapped to input 5.
-1,999.000 to 9,999.000
4.0
Instance 1
0x86 (134)
1
Map 1 Map 2
- - - -
3602 0x16 (22)
166
34022
float
RWES
Note:
Some values will be rounded off to fit in the four-character display. Full values can be read with other interfaces.
* Available with PM4, PM8 and PM9 models only
Watlow EZ-ZONE ® PM PID Controller
•
47
•
R: Read
W: Write
E: EEPROM
S: User
Set
Chapter 6 Setup Page
Setup Page
CIP
Modbus RelaClass
tive
Instance
Address
Attribute
hex (dec)
Data
Type
&
Read/
Write
Profibus
Index
Parameter ID
Instance 1
0x86 (134)
1
Map 1 Map 2
----
3584 0xD (13)
167
34013
float
RWES
5.0
Instance 1
0x86 (134)
1
Map 1 Map 2
----
3604 0x17 (23)
168
34023
float
RWES
-1,999.000 to 9,999.000
6.0
Instance 1
0x86 (134)
1
Map 1 Map 2
----
3586 0xE (14)
169
34014
float
RWES
Linearization (1)
Output Point 7
Set the value that will be
mapped to input 7.
-1,999.000 to 9,999.000
6.0
Instance 1
0x86 (134)
1
Map 1 Map 2
----
3606 0x18 (24)
170
34024
float
RWES
[`iP;8]
[ ip.8]
Linearization (1)
Input Point 8
Set the value that will be
mapped to output 8.
-1,999.000 to 9,999.000
7.0
Instance 1
0x86 (134)
1
Map 1 Map 2
----
3588 0xF (15)
171
34015
float
RWES
[`oP;8]
[ op.8]
Linearization (1)
Output Point 8
Set the value that will be
mapped to input 8.
-1,999.000 to 9,999.000
7.0
Instance 1
0x86 (134)
1
Map 1 Map 2
----
3608 0x19 (25)
172
34025
float
RWES
[`iP;9]
[ ip.9]
Linearization (1)
Input Point 9
Set the value that will be
mapped to output 9.
-1,999.000 to 9,999.000
8.0
Instance 1
0x86 (134)
1
Map 1 Map 2
----
3590 0x10 (16)
173
34016
float
RWES
[`oP;9]
[ op.9]
Linearization (1)
Output Point 9
Set the value that will be
mapped to input 9.
-1,999.000 to 9,999.000
8.0
Instance 1
0x86 (134)
1
Map 1 Map 2
----
3610 0x1A (26)
174
34026
float
RWES
[iP;10]
[ip.10]
Linearization (1)
Input Point 10
Set the value that will be
mapped to output 10.
-1,999.000 to 9,999.000
9.0
Instance 1
0x86 (134)
1
Map 1 Map 2
----
3592 0x11 (17)
175
34017
float
RWES
[oP;10]
[op.10]
Linearization (1)
Output Point 10
Set the value that will be
mapped to input 10.
-1,999.000 to 9,999.000
9.0
Instance 1
0x86 (134)
1
Map 1 Map 2
----
3612 0x1B (27)
176
34027
float
RWES
Off
Instance 1
0x7E (126)
1
Map 1 Map 2
0x15
(21)
----
3320
123
26021
uint
RWES
Display
Parameter Name
Description
[`iP;6]
[ ip.6]
Linearization (1)
Input Point 6
Set the value that will be
mapped to output 6.
-1,999.000 to 9,999.000
5.0
[`oP;6]
[ op.6]
Linearization (1)
Output Point 6
Set the value that will be
mapped to input 6.
-1,999.000 to 9,999.000
[`iP;7]
[ ip.7]
Linearization (1)
Input Point 7
Set the value that will be
mapped to output 7.
[`oP;7]
[ op.7]
Range
Default
[``Pu]*
[`Set]
Process Value Menu
[``Fn]
[ Fn]
Process Value (1)
[`oFF] Off (62)
Function
[`alt] *Pressure to AltiSet the function that will
tude (1649)
be applied to the source or
sources.
Note:
Some values will be rounded off to fit in the four-character display. Full values can be read with other interfaces.
* Available with PM4, PM8 and PM9 models only
Watlow EZ-ZONE ® PM PID Controller
•
48
•
R: Read
W: Write
E: EEPROM
S: User
Set
Chapter 6 Setup Page
Setup Page
Data
Type
&
Read/
Write
Parameter ID
Instance 1
0x7E (126)
1
Map 1 Map 2
----
3334 0x1C (28)
----
26028
uint
RWES
HFt
Instance 1
0x7E (126)
1
Map 1 Map 2
----
3336 0x1D (29)
----
26029
uint
RWES
0.0
Instance 1
0x7E (126)
1
Map 1 Map 2
----
3330 0x1A (26)
----
26026
float
RWES
Instance 1
0x6A (106)
5 to 6
Map 1 Map 2
1
1000 1120
82
6001
uint
RWES
83
6005
uint
RWES
Parameter Name
Description
[p;unt]
[P.unt]
Process Value (1)
Pressure Units*
Set the units that will be
applied to the source.
[`psi] Pounds per Square PSI
Inch (1671)
[pasc] Pascal (1674)
[atm] Atmosphere (1675)
[mbr] Millibar (1672)
[torr] Torr (1673)
[a;unt]
[A.unt]
Process Value (1)
Altitude Units*
Set the units that will be
applied to the source.
[`Hft] Kilofeet (1677)
[``ft] Feet (1676)
[`Fil]
[ FiL]
Process Value (1)
0.0 to 60.0 seconds
Filter
Filtering smooths out the
output signal of this function block. Increase the
time to increase filtering.
Range
CIP
Modbus RelaClass
tive
Instance
Address
Attribute
hex (dec)
Profibus
Index
Display
Default
[`dio]
[`Set]
Digital Input/Output Menu
[`dir]
[ dir]
[``Fn]
[ Fn]
Digital Input/Output (5
Output
[OtPt] Output (68)
to 6)
[iCon] Input Dry Contact
Direction
(44)
Set this function to oper- [``in] Input Voltage (193)
ate as an input or output.
Digital Output (5 to 6)
Action Function
Select what function will
drive this output.
Instance 1
0x6A (106)
1 to 2
Map 1 Map 2
5
1008 1128
Off
[`oFF] Off (62)
[lim] Limit (126)
[Ent;b] Profile Event Out
B (234)
[Ent;A] Profile Event Out
A (233)
[SoF;2] Special Function
Output 2 (1533)
[SoF;1] Special Function
Output 1 (1532)
[CooL] Cool Power, Control Loop (161)
[heat] Heat Power, Control Loop (160)
[ALM] Alarm (6)
Offset to next
instance (Map
1 & Map 2)
equals +30
Offset to next
instance (Map
1 & Map 2)
equals +30
Note:
Some values will be rounded off to fit in the four-character display. Full values can be read with other interfaces.
* Available with PM4, PM8 and PM9 models only
R: Read
W: Write
E: EEPROM
S: User
Set
* Pressure Altitude calculation is based on the International Standard Atmosphere, 1976
Watlow EZ-ZONE ® PM PID Controller
•
49
•
Chapter 6 Setup Page
Setup Page
Display
[``Fi]
[ Fi]
Parameter Name
Description
Digital Output (5 to 6)
Function Instance
Set the instance of the
function selected above.
Range
Default
1 to 4
CIP
Modbus RelaClass
tive
Instance
Address
Attribute
hex (dec)
Instance 1
0x6A (106)
5 to 6
Map 1 Map 2
6
1010 1130
1
Data
Type
&
Read/
Write
Profibus
Index
Parameter ID
84
6006
uint
RWES
85
6002
uint
RWES
86
6003
float
RWES
87
6009
float
RWES
88
6010
float
RWES
Offset to next
instance (Map
1 & Map 2)
equals +30
[`o;Ct]
[ o.Ct]
[`o;tb]
[ o.tb]
Digital Output (5 to 6)
Control
Set the output control
type. This parameter
is only used with PID
control, but can be set
anytime.
[`Ftb] Fixed Time Base
(34)
[`utb] Variable Time
Base (103)
Digital Output (5 to 6)
Time Base
Set the time base for
fixed-time-base control.
[ 0.1 for Fast and Bi-Directional outputs, 5.0 for
Slow outputs] to 60
Instance 1
0x6A (106)
5 to 6
Map 1 Map 2
2
1002 1122
Fixed
Time
Base
Offset to next
instance (Map
1 & Map 2)
equals +30
----
Instance 1
0x6A (106)
5 to 6
Map 1 Map 2
3
1016 1124
Offset to next
instance (Map
1 & Map 2)
equals +30
[`o;Lo]
[ o.Lo]
[`o;hi]
[ o.hi]
Digital Output (5 to 6)
Low Power Scale
The power output will
never be less than the
value specified and will
represent the value at
which output scaling
begins.
0.0 to 100.0
Digital Output (5 to 6)
High Power Scale
The power output will
never be greater than
the value specified and
will represent the value
at which output scaling
stops.
0.0 to 100.0
Instance 1
0x6A (106)
5 to 6
Map 1 Map 2
9
1016 1136
0.0
Offset to next
instance (Map
1 & Map 2)
equals +30
Instance 1
0x6A (106)
5 to 6
Map 1 Map 2
1018 1138 0xA (10)
100.0
Offset to next
instance (Map
1 & Map 2)
equals +30
Note:
Some values will be rounded off to fit in the four-character display. Full values can be read with other interfaces.
* Available with PM4, PM8 and PM9 models only
Watlow EZ-ZONE ® PM PID Controller
•
50
•
R: Read
W: Write
E: EEPROM
S: User
Set
Chapter 6 Setup Page
Setup Page
Display
[`leu]
[ LEv]
[``Fn]
[ Fn]
Parameter Name
Description
Digital Input (5 to 6)
Level
Select which action will
be interpreted as a true
state.
Range
Default
Instance 1
0x6E (110)
5 to 6
Map 1 Map 2
1
1320 1560
High
[high] High (37)
[LoW] Low (53)
CIP
Modbus RelaClass
tive
Instance
Address
Attribute
hex (dec)
Data
Type
&
Read/
Write
Profibus
Index
Parameter ID
137
10001
uint
RW
138
10003
uint
RWES
Offset to next
instance (Map
1 & Map 2)
equals +20
Instance 1
0x6E (110)
1 to 2
Map 1 Map 2
3
1324 1564
Digital Input (5 to 6)
None
[none] None (61)
Action Function
[s;stp] Profile Start Step
Select the function that
(1077)
will be triggered by a true [P;StS] Profile Start/Stop,
state for Digital Input 5
level triggered (208)
and or 6.
[ProF] Profile Start Number, edge triggered (196)
[P;hoL] Profile Hold/
Resume, level triggered
(207)
[P;diS] Profile Disable,
level triggered (206)
Offset to next
instance (Map
1 & Map 2)
equals +20
[`t;da] TRU-TUNE+® Disable, level triggered (219)
[`oFF] Control Outputs
Off, level triggered (90)
[MAn] Manual/Auto
Mode, level triggered (54)
[tUnE] Tune, edge triggered (98)
[idLE] Idle Set Point Enable, level triggered (107)
[`F;AL] Force Alarm, level
triggered (218)
[`AoF] Alarm Outputs &
Control Loop Off, level
triggered (220)
[`SiL] Silence Alarms,
edge triggered (108)
[ALM] Alarm Reset, edge
triggered (6)
[P;LoC] Lock Keypad, level
triggered (217)
[usr;r] Restore User Settings, edge triggered
(227)
[LMr] Limit Reset, edge
triggered (82)
Note:
Some values will be rounded off to fit in the four-character display. Full values can be read with other interfaces.
* Available with PM4, PM8 and PM9 models only
Watlow EZ-ZONE ® PM PID Controller
•
51
•
R: Read
W: Write
E: EEPROM
S: User
Set
Chapter 6 Setup Page
Setup Page
Display
[``Fi]
[ Fi]
Parameter Name
Description
Range
Default
Digital Input (5 to 7)
0 to 4
Function Instance
Select which Digital Input
will be triggered by a true
state.
CIP
Modbus RelaClass
tive
Instance
Address
Attribute
hex (dec)
Instance 1
0x6E (110)
5 to 7
Map 1 Map 2
4
1326 1566
0
Data
Type
&
Read/
Write
Profibus
Index
Parameter ID
139
10004
uint
RWES
Offset to next
instance (Map
1 & Map 2)
equals +20
[LooP]
[`Set]
Control Loop Menu
[`h;Ag]
[ h.Ag]
Control Loop (1)
Heat Algorithm
Set the heat control
method.
[`oFF] Off (62)
[`Pid] PID (71)
[on;of] On-Off (64)
PID
Instance 1
0x97 (151)
1
Map 1 Map 2
3
1884 2364
72
8003
uint
RWES
[`C;Ag]
[ C.Ag]
Control Loop (1)
Cool Algorithm
Set the cool control
method.
[`oFF] Off (62)
[`Pid] PID (71)
[on;of] On-Off (64)
Off
Instance 1
0x97 (151)
1
Map 1 Map 2
4
1886 2366
73
8004
uint
RWES
[`C;Cr]
[ C.Cr]
Control Loop (1)
Cool Output Curve
Select a cool output
curve to change the
responsiveness of the
system.
[`oFF] Off (62)
[`Cr;A] Non-linear Curve
1 (214)
[`Cr;b] Non-linear Curve
2 (215)
Off
Instance 1
0x97 (151)
1
Map 1 Map 2
5
1888 2368
----
8038
uint
RWES
[t;tUn]
[t.tUn]
Control Loop (1)
TRU-TUNE+™ Enable
Enable or disable the
TRU-TUNE+™ adaptive
tuning feature.
[``no] No (59)
[`YES} Yes (106)
No
Instance 1
0x97 (151)
1
Map 1 Map 2
1910 2390 0x10 (16)
----
8022
uint
RWES
[t;bnd]
[t.bnd]
Control Loop (1)
0 to 100
TRU-TUNE+™ Band
Set the range, centered
on the set point, within
which TRU-TUNE+™ will
be in effect. Use this function only if the controller
is unable to adaptive tune
automatically.
0
Instance 1
0x97 (151)
1
Map 1 Map 2
1912 2392 0x11 (17)
----
8034
uint
RWES
[`t;gn]
[ t.gn]
Control Loop (1)
1 to 6
TRU-TUNE+™ Gain
Select the responsiveness
of the TRU-TUNE+™
adaptive tuning calculations. More responsiveness may increase overshoot.
3
Instance 1
0x97 (151)
1
Map 1 Map 2
1914 2394 0x12 (18)
----
8035
uint
RWES
[t;Agr]
[t.Agr]
Control Loop (1)
[Undr] Under damped
Autotune Aggressive(99)
ness
[Crit] Critical damped
Select the aggressiveness
(21)
of the autotuning calcula- [OuEr] Over damped (69)
tions.
Critical
Instance 1
0x97 (151)
1
Map 1 Map 2
1916 2396 0x13 (19)
----
8024
uint
RWES
Note:
Some values will be rounded off to fit in the four-character display. Full values can be read with other interfaces.
* Available with PM4, PM8 and PM9 models only
Watlow EZ-ZONE ® PM PID Controller
•
52
•
R: Read
W: Write
E: EEPROM
S: User
Set
Chapter 6 Setup Page
Setup Page
Display
Parameter Name
Description
Range
Default
0.0
CIP
Modbus RelaClass
tive
Instance
Address
Attribute
hex (dec)
Data
Type
&
Read/
Write
Profibus
Index
Parameter ID
Instance 1
0x97 (151)
1
Map 1 Map 2
----
- - - - 0x1C (28)
----
8051
float
RWES
[p;dl]
[ P.dL]
Control Loop (1)
0.0 to 5.0
Peltier Delay
Set a value that will
cause a delay when
switching from heat mode
to cool mode.
[`UFA]
[UFA]
Control Loop (1)
User
[`oFF] Off, sets output
User Failure Action
power to 0% (62)
Select what the controller [bPLS] Bumpless, mainoutputs will do when the
tains same output power,
user switches control to
if it was less than 75%
manual mode.
and stable, otherwise 0%
(14)
[MAn] Manual Fixed, sets
output power to Manual
Power setting (33)
[USEr] User, sets output
power to last open-loop
set point the user entered (100)
Instance 1
0x6B (107)
1
Map 1 Map 2
2182 2662 0xC (12)
----
7012
uint
RWES
[FAiL]
[FAiL]
Control Loop (1)
User
[`oFF] Off, sets output
Input Error Failure
power to 0% (62)
Select what the controller [bPLS] Bumpless, mainoutputs will do when an
tains same output power,
input error switches conif it was less than 75%
trol to manual mode.
and stable, otherwise 0%
(14)
[MAn] Manual Fixed, sets
output power to Manual
Power setting (33)
[USEr] User, sets output
power to last open-loop
set point the user entered (100)
Instance 1
0x6B (107)
1
Map 1 Map 2
2184 2664 0xD (13)
----
7013
uint
RWES
[MAn]
[MAn]
Control Loop (1)
Set Point Open Loop Limit 0.0
Manual Power
Low to Set Point Open
Set the manual output
Loop Limit High (Setup
power level that will take
Page)
effect if an input error
failure occurs while User
Failure Action is set to
Manual Fixed.
Instance 1
0x6B (107)
1
Map 1 Map 2
2180 2660 0xB (11)
----
7011
float
RWES
[`L;dE]
[ L.dE]
Control Loop (1)
[``no] No (59)
Open Loop Detect En[`YES} Yes (106)
able
Turn on the open-loop
detect feature to monitor
a closed-loop operation for
the appropriate response.
No
Instance 1
0x97 (151)
1
Map 1 Map 2
0x16
(22)
1922 2402
74
8039
uint
RWES
[`L;dt]
[ L.dt]
Control Loop (1)
0 to 3,600 seconds
Open Loop Detect Time
The Open Loop Detect
Deviation value must occur for this time period to
trigger an open-loop error.
240
Instance 1
0x97 (151)
1
Map 1 Map 2
1924 2404 0x17 (23)
75
8040
uint
RWES
Note:
Some values will be rounded off to fit in the four-character display. Full values can be read with other interfaces.
* Available with PM4, PM8 and PM9 models only
Watlow EZ-ZONE ® PM PID Controller
•
53
•
R: Read
W: Write
E: EEPROM
S: User
Set
Chapter 6 Setup Page
Setup Page
Display
Parameter Name
Description
Range
Default
CIP
Modbus RelaClass
tive
Instance
Address
Attribute
hex (dec)
Profibus
Index
Parameter ID
Data
Type
&
Read/
Write
[`L;dd]
[ L.dd]
Control Loop (1)
-1,999.000 to 9,999.000°F
Open Loop Detect Deor units
viation
-1,110.555 to 5,555.000°C
Set the value that the
process must deviate from
the set point to trigger an
open-loop error.
10.0°F or
units
6.0°C
Instance 1
0x97 (151)
1
Map 1 Map 2
1926 2406 0x18 (24)
76
8041
float
RWES
[``rP]
[ rP]
Control Loop (1)
`oFF] Off (62)
Ramp Action
[`Str] Startup (88)
Select when the control[StPt] Set Point Change
ler's set point will ramp to (1647)
the defined end set point.
[both] Both (13)
Off
Instance 1
0x6B (107)
1
Map 1 Map 2
2186 2666 0xE (14)
56
7014
uint
RWES
[`r;SC]
[ r.SC]
Control Loop (1)
Ramp Scale
Select the scale of the
ramp rate.
Minutes
Instance 1
0x6B (107)
1
Map 1 Map 2
2188 2668 0xF (15)
57
7015
uint
RWES
[`r;rt]
[ r.rt]
Control Loop (1)
0.0 to 9,999.000°F or units 1.0°F or
Ramp Rate
units
0.0 to 5,555.000°C
Set the rate for the set
1.0°C
point ramp. Set the time
units for the rate with the
Ramp Scale parameter.
Instance 1
0x6B (107)
1
Map 1 Map 2
2192 2672 0x11 (17)
58
7017
float
RWES
[`L;SP]
[ L.SP]
Control Loop (1)
-1,999.000 to 9,999.000°F
Low Set Point
or units
Set the minimum value of -1,128.000 to 5,537.000°C
the closed loop set point
range.
-1,999°F
or units
-1,128°C
Instance 1
0x6B (107)
1 to 2
Map 1 Map 2
3
2164 2644
52
7003
float
RWES
[`h;SP]
[ h.SP]
Control Loop (1)
-1,999.000 to 9,999.000°F
High Set Point
or units
Set the maximum value of -1,128.000 to 5,537.000°C
the closed loop set point
range..
-1,999°F
or units
-1,128°C
Instance 1
0x6B (107)
1
Map 1 Map 2
4
2166 2646
53
7004
float
RWES
[SP;Lo]
[SP.Lo]
Control Loop (1)
Set Point Open Limit
Low
Set the minimum value
of the open-loop set point
range.
-100 to 100%
-100
Instance 1
0x6B (107)
1
Map 1 Map 2
5
2168 2649
54
7005
float
RWES
[SP;hi]
[SP.hi]
Control Loop (1)
Set Point Open Limit
High
Set the maximum value
of the open-loop set point
range.
-100 to 100%
100
Instance 1
0x6B (107)
1
Map 1 Map 2
6
2170 2650
55
7006
float
RWES
[hoUr] Hours (39)
[Min] Minutes (57)
Note:
Some values will be rounded off to fit in the four-character display. Full values can be read with other interfaces.
* Available with PM4, PM8 and PM9 models only
Watlow EZ-ZONE ® PM PID Controller
•
54
•
R: Read
W: Write
E: EEPROM
S: User
Set
Chapter 6 Setup Page
Setup Page
Display
Parameter Name
Description
Range
CIP
Modbus RelaClass
tive
Instance
Address
Attribute
hex (dec)
Default
Data
Type
&
Read/
Write
Profibus
Index
Parameter ID
83
6005
uint
RWES
84
6006
uint
RWES
85
6002
uint
RWES
86
6003
float
RWES
87
6009
float
RWES
[otpt]
[`Set]
Output Menu
[``Fn]
[ Fn]
[``Fi]
[ Fi]
Output Digital (1 to 2)
Function
Select what function will
drive this output.
Output Digital (1 to 2)
Function Instance
Set the instance of the
function selected above.
[`oFF] Off (62)
[Ent;b] Profile Event Out
B (234)
[Ent;A] Profile Event Out
A (233)
[Cool] Cool (20)
[heat] Heat (36)
[ALM] Alarm (6)
Output 1
Heat
Output 2
Alarm
Output 3
Off
Output 4
Off
1 to 2
1
Instance 1
0x6A (106)
1 to 2
Map 1 Map 2
5
- 888 1008
-
- Offset to next
instance (Map
- 1 & Map 2)
equals +30
Instance 1
0x6A (106)
1 to 2
Map 1 Map 2
6
890 1010
Offset to next
instance (Map
1 & Map 2)
equals +30
[`o;Ct]
[ o.Ct]
[`o;tb]
[ o.tb]
[`o;Lo]
[ o.Lo]
Fixed
Time
Base
Instance 1
0x6A (106)
1 to 4
Map 1 Map 2
2
882 1002
Output Digital (1 to 2)
Control
Set the output control
type. This parameter
is only used with PID
control, but can be set
anytime.
[`Ftb] Fixed Time Base
(34)
[`utb] Variable Time
Base (103)
Output Digital (1 to 2)
Time Base
Set the time base for
fixed-time-base control.
0.1 to 60.0 seconds (solidstate relay or switched
dc)
5.0 to 60.0 seconds (mechanical relay or no-arc
power control)
0.1 sec.
[SSR &
sw dc]
20.0 sec.
[mech,
relay,
no-arc]
Instance 1
0x6A (106)
1 to 2
Map 1 Map 2
3
884 1004
0.0 to 100.0%
0.0%
Instance 1
0x6A (106)
1 to 2
Map 1 Map 2
9
896 1016
Output Digital (1 to 2)
Low Power Scale
The power output will
never be less than the
value specified and will
represent the value at
which output scaling
begins.
Offset to next
instance (Map
1 & Map 2)
equals +30
Offset to next
instance (Map
1 & Map 2)
equals +30
Note:
Some values will be rounded off to fit in the four-character display. Full values can be read with other interfaces.
* Available with PM4, PM8 and PM9 models only
Watlow EZ-ZONE ® PM PID Controller
Offset to next
instance (Map
1 & Map 2)
equals +30
•
55
•
R: Read
W: Write
E: EEPROM
S: User
Set
Chapter 6 Setup Page
Setup Page
Display
[`o;hi]
[ o.hi]
Parameter Name
Description
Output Digital (1 to 2)
High Power Scale
The power output will
never be greater than
the value specified and
will represent the value
at which output scaling
stops.
Range
Default
0.0 to 100.0%
100.0%
CIP
Modbus RelaClass
tive
Instance
Address
Attribute
hex (dec)
Instance 1
0x6A (106)
1 to 2
Map 1 Map 2
898 1018 0xA (10)
Data
Type
&
Read/
Write
Profibus
Index
Parameter ID
88
6010
float
RWES
Offset to next
instance (Map
1 & Map 2)
equals +30
[`o;ty]
[ o.ty]
Output Digital (1)
[uoLt] Volts (104)
Type
[`MA] Milliamps (112)
Select whether the process output will operate in
volts or milliamps.
Volts
Instance 1
0x76 (118)
1
Map 1 Map 2
1
720 840
95
18001
uint
RWES
[``Fn]
[ Fn]
Output Process (1)
Function
Set the type of function
that will drive this output.
[`oFF] Off (62)
[dupl] Duplex (212)
[Cool] Cool (20)
[heat] Heat (36)
[rmt] Retransmit (213)
[Ent;b] Profile Event Out
B (234)
[Ent;A] Profile Event Out
A (233)
[ALM] Alarm (6)
Off
Instance 1
0x76 (118)
1
Map 1 Map 2
2
722 842
96
18002
uint
RWES
[`r;Sr]
[ r.Sr]
Output Process (1)
Retransmit Source
Select the value that will
be retransmitted.
[``Ai] Analog Input (142) Analog
Input
[StPt] Set Point (85)
[CUrr] Current (22)
Instance 1
0x76 (118)
1
Map 1 Map 2
3
724 844
97
18003
uint
RWES
[``Fi]
[ Fi]
Output Process (1)
Function Instance
Set the instance of the
function selected above.
1 to 4
1
Instance 1
0x76 (118)
1
Map 1 Map 2
4
726 846
98
18004
uint
RWES
[`S;Lo]
[ S.Lo]
Output Process (1)
-100.0 to 100.0
Scale Low
Set the minimum value of
the output range.
0.00
Instance 1
0x76 (118)
1
Map 1 Map 2
9
736 856
99
18009
float
RWES
[`S;hi]
[ S.hi]
Output Process (1)
-100.0 to 100.0
Scale High
Set the maximum value of
the output range.
10.00
Instance 1
0x76 (118)
1
Map 1 Map 2
0xA (10)
738 858
100
18010
float
RWES
[`r;Lo]
[ r.Lo]
Output Process (1)
-1,999.000 to 9,999.000°F
Range Low
or units
Set the minimum value
-1,128.000 to 5,537.000°C
of the retransmit value
range in process units.
When the retransmit
source is at this value, the
retransmit output will be
at its Scale Low value.
0.0°F or
units
-18°C
Instance 1
0x76 (118)
1
Map 1 Map 2
0xB (11)
740 860
101
18011
float
RWES
Note:
Some values will be rounded off to fit in the four-character display. Full values can be read with other interfaces.
* Available with PM4, PM8 and PM9 models only
Watlow EZ-ZONE ® PM PID Controller
•
56
•
R: Read
W: Write
E: EEPROM
S: User
Set
Chapter 6 Setup Page
Setup Page
Display
Parameter Name
Description
Range
CIP
Modbus RelaClass
tive
Instance
Address
Attribute
hex (dec)
Data
Type
&
Read/
Write
Profibus
Index
Parameter ID
9,999.0°F
Instance 1
0x76 (118)
or units Map 1 Map 2
1
0xC (12)
5,537.0°C 742 862
102
18012
float
RWES
Default
[`r;hi]
[ r.hi]
Output Process (1)
-1,999.000 to 9,999.000°F
Range High
or units
Set the maximum value
-1,128.000 to 5,537.000°C
of the retransmit value
range in process units.
When the retransmit
source is at this value, the
retransmit output will be
at its Scale High value.
[`o;lo]
[ o.Lo]
Output Process (1)
Low Power Scale
The power output will
never be less than the
value specified and will
represent the value at
which power scaling begins.
0.0 to 100%
0.0%
Instance 1
0x76 (118)
Map 1 Map 2
1
744 864 0x0D (13)
103
18013
float
RWES
[`o;hi]
[ o.hi]
Output Process (1)
0.0 to 100%
High Power Scale
The power output will
never be greater than the
value specified and will
represent the value at
which power scaling stops.
100%
Instance 1
0x76 (118)
Map 1 Map 2
1
746 866 0x0E (14)
104
18014
float
RWES
[`o;CA]
[ o.CA]
Output Process (1)
Calibration Offset
Set an offset value for a
process output.
0.0°F or
units
0.0°C
Instance 1
0x76 (118)
1
Map 1 Map 2
7
732 852
105
18007
float
RWES
Instance 1
0x6D (109)
1 to 4
Map 1 Map 2
1508 1908 0xF (15)
20
9015
uint
RWES
21
9017
uint
RWES
-1,999.000 to 9,999.000°F
or units
-1,110.555 to 5,555.000°C
[Alm]
[`Set]
Alarm Menu
[`A;ty]
[ A.ty]
[`Sr;A]
[ Sr.A]
Alarm (1 to 4)
Type
Select whether the alarm
trigger is a fixed value or
will track the set point.
Off
[`oFF] Off (62)
[PR;AL] Process Alarm (76)
[dE;AL] Deviation Alarm
(24)
Alarm (1 to 4)
Source Function A
Select what will trigger
this alarm.
Instance 1
0x6D (109)
[``Ai] Analog Input (142) If Alarm
type is
1 to 4
Map 1 Map 2
[PWr] Power, Control
set to
Loop (73)
1512
1912 0x11 (17)
Devia[``Pu] Process Value
tion or
(241)
Process. Offset to next
[`Lnr] Linearization (238)
instance (Map
1 & Map 2)
[CUrr] Current (22)
equals +60
Offset to next
instance (Map
1 & Map 2)
equals +60
Note:
Some values will be rounded off to fit in the four-character display. Full values can be read with other interfaces.
* Available with PM4, PM8 and PM9 models only
Watlow EZ-ZONE ® PM PID Controller
•
57
•
R: Read
W: Write
E: EEPROM
S: User
Set
Chapter 6 Setup Page
Setup Page
Display
[`A;hy]
[ A.hy]
[`A;Lg]
[ A.Lg]
[`A;Sd]
[ A.Sd]
Parameter Name
Description
Range
Alarm (1 to 4)
Hysteresis
Set the hysteresis for an
alarm. This determines
how far into the safe
region the process value
needs to move before the
alarm can be cleared.
0.001 to 9,999.000°F or
units
0.001 to 5,555.000°C
Alarm (1 to 4)
Logic
Select what the output
condition will be during
the alarm state.
[`AL;C] Close On Alarm
(17)
[`AL;o] Open On Alarm
(66)
Default
1.0°F or
units
1.0°C
CIP
Modbus RelaClass
tive
Instance
Address
Attribute
hex (dec)
Instance 1
0x6D (109)
1 to 4
Map 1 Map 2
3
1484 1884
Data
Type
&
Read/
Write
Profibus
Index
Parameter ID
24
9003
float
RWES
25
9005
uint
RWES
26
9004
uint
RWES
27
9007
uint
RWES
28
9008
uint
RWES
Offset to next
instance (Map
1 equals +50,
for Map 2
equals +60)
Close On
Alarm
Instance 1
0x6D (109)
1 to 4
Map 1 Map 2
5
1488 1888
Offset to next
instance (Map
1 equals +50,
for Map 2
equals +60)
Instance 1
0x6D (109)
1 to 4
Map 1 Map 2
4
1486 1886
Both
Alarm (1 to 4)
[both] Both (13)
Sides
[high] High (37)
Select which side or sides [LoW] Low (53)
will trigger this alarm.
Offset to next
instance (Map
1 equals +50,
for Map 2
equals +60)
[`A;LA]
[ A.LA]
[`A;bL]
[ A.bL]
Alarm (1 to 4)
[nLAt] Non-Latching (60)
Latching
[`LAt] Latching (49)
Turn alarm latching on or
off. A latched alarm has to
be turned off by the user.
NonInstance 1
0x6D (109)
Latching Map 1 Map 2
1 to 4
7
1492 1892
Alarm (1 to 4)
Blocking
Select when an alarm will
be blocked. After startup
and/or after the set point
changes, the alarm will be
blocked until the process
value enters the normal
range.
Off
[`oFF]
[`Str]
[StPt]
[both]
Offset to next
instance (Map
1 equals +50,
for Map 2
equals +60)
Off (62)
Startup (88)
Set Point (85)
Both (13)
Instance 1
0x6D (109)
1 to 4
Map 1 Map 2
8
1494
1894
Offset to next
instance (Map
1 equals +50,
for Map 2
equals +60)
Note:
Some values will be rounded off to fit in the four-character display. Full values can be read with other interfaces.
* Available with PM4, PM8 and PM9 models only
Watlow EZ-ZONE ® PM PID Controller
•
58
•
R: Read
W: Write
E: EEPROM
S: User
Set
Chapter 6 Setup Page
Setup Page
Display
[`A;Si]
[ A.Si]
Parameter Name
Description
Alarm (1 to 4)
Silencing
Turn alarm silencing on
to allow the user to disable this alarm.
Range
Default
Instance 1
0x6D (109)
1 to 4
Map 1 Map 2
6
1490 1890
Off
[`oFF] Off (62)
[``on] On (63)
CIP
Modbus RelaClass
tive
Instance
Address
Attribute
hex (dec)
Data
Type
&
Read/
Write
Profibus
Index
Parameter ID
29
9006
uint
RWES
30
9016
uint
RWES
31
9021
uint
RWES
137
10001
uint
RWES
Offset to next
instance (Map
1 equals +50,
for Map 2
equals +60)
Instance 1
0x6D (109)
1 to 4
Map 1 Map 2
0x10
(16)
1510 1910
On
[A;dSP] Alarm (1 to 4)
[`oFF] Off (62)
[A.dSP] Display
[``on] On (63)
Display an alarm message
when an alarm is active.
Offset to next
instance (Map
1 equals +50,
for Map 2
equals +60)
[`A;dL]
[ A.dL]
Alarm (1 to 4)
0 to 9,999 seconds
Delay
Set the span of time that
the alarm will be delayed
after the process value exceeds the alarm set point.
Instance 1
0x6D (109)
1 to 4
Map 1 Map 2
1520 1920 0x15 (21)
0
Offset to next
instance (Map
1 equals +50,
for Map 2
equals +60)
[`FUn]
[`Set]
Function Key Menu
`leu]
[ LEv]
Function Key (1 to 2)
Level
The Function Key will
always power up in the
low state.
Instance 1
0x6E (110)
1 to 2
Map 1 Map 2
1
1320 1560
Instance 2
Map 1 Map 2
1340 1580
High
high] High (37)
[Low] Low (53)
Pressing the Function Key
will toggle the selected
action.
Note:
Some values will be rounded off to fit in the four-character display. Full values can be read with other interfaces.
* Available with PM4, PM8 and PM9 models only
Watlow EZ-ZONE ® PM PID Controller
•
59
•
R: Read
W: Write
E: EEPROM
S: User
Set
Chapter 6 Setup Page
Setup Page
Display
[``Fn]
[ Fn]
Function Key (1 to 2)
Digital Input Function
Program the EZ Key to
trigger an action.
Functions respond to a
level state change or an
edge level change.
CIP
Modbus RelaClass
tive
Instance
Address
Attribute
hex (dec)
Data
Type
&
Read/
Write
Profibus
Index
Parameter ID
Instance 1
0x6E (110)
1 to 2
Map 1 Map 2
3
1324 1564
Instance 2
Map 1 Map 2
1344 1584
138
10003
uint
RWES
0
Instance 1
0x96 (110)
1 to 2
Map 1 Map 2
4
1326 1566
Instance 2
Map 1 Map 2
1346 1586
139
10004
uint
RWES
[```F] °F (30)
[```C] °C (15)
°F
Instance 1
0x67 (103)
1
Map 1 Map 2
5
1838 2308
110
3005
uint
RWES
[``50] 50 Hz (3)
[``60] 60 Hz (4)
60 Hz
Instance 1
0x6A (106)
1
Map 1 Map 2
4
886 1006
89
1034
uint
RWES
Parameter Name
Description
Range
Default
None
[none] None (61)
[s;stp] Profile Start Step
(1077)
[P;StS] Profile Start/Stop,
level triggered (208)
[ProF] Profile Start Number, edge triggered (196)
[P;hoL] Profile Hold/
Resume, level triggered
(207)
[P;diS] Profile Disable,
level triggered (206)
[`t;da] TRU-TUNE+® Disable, level triggered (219)
[`oFF] Control Outputs
Off, level triggered (90)
[MAn] Manual/Auto
Mode, level triggered (54)
[tUnE] Tune, edge triggered (98)
[idLE] Idle Set Point Enable, level triggered (107)
[`F;AL] Force Alarm, level
triggered (218)
[`AoF] Alarm Outputs &
Control Loop Off, level
triggered (220)
[`SiL] Silence Alarms,
edge triggered (108)
[ALM] Alarm Reset, edge
triggered (6)
[P;LoC] Lock Keypad, level
triggered (217)
[usr;r] Restore User Settings, edge triggered
(227)
[``Fi]
[ Fi]
Function Key (1 to 2)
0 to 4
Instance
Select which instance the
EZ Key will affect. If only
one instance is available,
any selection will affect it.
[gLbL]
[`Set]
Global Menu
[`C_F]
[ C_F]
Global
Display Units
Select which scale to use
for temperature.
[AC;LF] Global
[AC.LF] AC Line Frequency
Set the frequency to the
applied ac line power
source.
Note:
Some values will be rounded off to fit in the four-character display. Full values can be read with other interfaces.
* Available with PM4, PM8 and PM9 models only
Watlow EZ-ZONE ® PM PID Controller
•
60
•
R: Read
W: Write
E: EEPROM
S: User
Set
Chapter 6 Setup Page
Setup Page
Display
Parameter Name
Description
Range
Default
CIP
Modbus RelaClass
tive
Instance
Address
Attribute
hex (dec)
Profibus
Index
Parameter ID
Data
Type
&
Read/
Write
Time
Instance 1
0x7A (122)
1
Map 1 Map 2
26 (38)
----
4414
----
22038
uint
RWE
Profile
[StPt] Set Point (85)
Profile Type
[`Pro] Process (75)
Set the profile startup to
be based on a set point or
a process value.
Set Point
Instance 1
0x7A (122)
1
Map 1 Map 2
8
2534 4354
----
22008
uint
RWE
[`GSE]
[ gSE]
Profile
[`oFF] Off (62)
Guaranteed Soak En[``on] On (63)
able
Enables the guaranteed
soak deviation function in
profiles.
Off
Instance 1
0x7A (122)
1
Map 1 Map 2
6
2530 4350
----
22006
uint
RWE
[GSd1]
[gSd1]
Profile
Guaranteed Soak Deviation 1
Set the value of the deviation band that will be
used in all profile step
types. The process value
must enter the deviation
band before the step can
proceed.
0.0 to 9,999.000°F or units 10.0°F or
units
0.0 to 5,555.000°C
6.0°C
Instance 1
0x7A (122)
1
Map 1 Map 2
7
2532 4352
----
22007
float
RWE
[`Si;a]
[ Si.a]
Profile Event Input
Source Instance A
Set the digital source for
WE1..
5 to 6
5
Instance 1
0x7A (122)
1
Map 1 Map 2
----
4390 0x1A (26)
----
22060
uint
RWES
[`Si;B]
[ Si.b]
Profile Event Input
Source Instance B
Set the digital source for
WE2..
5 to 6
5
Instance 1
7A (122)
1
Map 1 Map 2
- - - -
4392 0x1B (27)
----
22061
uint
RWES
[poti]
[Poti]
Global Menu
0 to 9999 seconds
Power Out Time
If profile is running and
power is lost, profile
will resume where it
left off provided time set
has not expired prior to
power restoration.
0
Instance 1
7A (122)
1
Map 1 Map 2
0x49
(73)
- - - -
4484
----
22073
uint
RWE
both
Instance 1
0x6A (103)
1
Map 1 Map 2
1856 2326 0x0E (14)
----
3014
uint
RWES
On
Instance 1
0x6A (103)
1
Map 1 Map 2
----
2350 0x1A (26)
----
3026
uint
RWES
[R;typ]
[R.tyP]
Profile
Ramping Type
[P;typ]
[P.tyP]
[C;led] Global Menu
[C.LEd] Communications LED
Action
Turns comms LED on or
off for selected comms
ports.
[2one]
[Zone]
[rate] Rate (81)
[``ti] Time (143)
[Con1] Comm port 2
(1189)
[Con2] Comm port 1
(1190)
[both] Comm port 1 and
2 (13)
[`off] Off (62)
Global Menu
[`off] Off (62)
Zone
[``on] On (63)
Turns Zone LED on or off
based on selection.
Note:
Some values will be rounded off to fit in the four-character display. Full values can be read with other interfaces.
* Available with PM4, PM8 and PM9 models only
Watlow EZ-ZONE ® PM PID Controller
•
61
•
R: Read
W: Write
E: EEPROM
S: User
Set
Chapter 6 Setup Page
Setup Page
Display
Parameter Name
Description
Range
Default
CIP
Modbus RelaClass
tive
Instance
Address
Attribute
hex (dec)
Profibus
Index
Parameter ID
Data
Type
&
Read/
Write
On
Instance 1
0x6A (103)
1
Map 1 Map 2
----
2352 0x1B (27)
----
3027
uint
RWES
1 to 10
2
Instance 1
0x6A (103)
1
Map 1 Map 2
----
2354 0x1C (28)
----
3028
uint
RWES
Global Menu
Display Time
Time delay in toggling
between channel 1 and
channel 2.
0 to 60
0
Instance 1
0x6A (103)
1
Map 1 Map 2
----
2356 0x1D (29)
----
3029
uint
RWES
[USr;S]
[USr.S]
Global Menu
User Settings Save
Save all of this controller's settings to the selected set.
[SEt1] User Set 1 (101)
[SEt2] User Set 2 (102)
[none] None (61)
None
Instance 1
Map 1 Map 2
26 26
0x(101)
1
0xE (14)
118
1014
uint
RWE
[USr;r]
[USr.r]
Global Menu
User Restore Settings
Replace all of this controller's settings with
another set.
[FCty]
[none]
[SEt1]
[SEt2]
Factory (31)
None (61)
User Set 1 (101)
User Set 2 (102)
None
Instance 1
Map 1 Map 2
24 24
0x65
(101)
1
0xD (13)
117
1013
uint
RWE
[Chan]
[Chan]
Global Menu
[`off] Off (62)
Channel
[``on] On (63)
Turns Channel LED on or
off based on selection.
[d;prs]
[dPrS]
Global Menu
Display Pairs
Defines the number of
Display Pairs.
[`d;ti]
[ d.ti]
[CoM]
[`SEt]
Communications Menu
[PCoL]
[PCoL]
Communications 1
[`Std] Standard Bus
Protocol
(1286)
Set the protocol of this
[Mod] Modbus RTU
controller to the protocol
(1057)
that this network is using.
Modbus
Instance 1
0x96 (150)
1
Map 1 Map 2
7
2492 2972
----
17009
uint
RWE
[`Ad;S]
[ Ad.S]
Communications 1
1 to 16
Address Standard Bus
Set the network address
of this controller. Each device on the network must
have a unique address.
The Zone Display on the
front panel will display
this number.
1
Instance 1
0x96 (150)
1
Map 1 Map 2
1
2480 2960
----
17001
uint
RWE
[Ad;M]
[Ad.M]
Communications (1)
1 to 247
Address Modbus
Set the network address
of this controller. Each device on the network must
have a unique address.
1
Instance 1
0x96 (150)
1
Map 1 Map 2
2
2482 2962
----
17007
uint
RWE
[bAUd]
[bAUd]
Communications (1)
Baud Rate Modbus
Set the speed of this controller's communications
to match the speed of the
serial network.
9,600
Instance 1
0x96 (150)
1
Map 1 Map 2
3
2484 2964
----
17002
uint
RWE
9,600 (188)
19,200 (189)
38,400 (190)
Note:
Some values will be rounded off to fit in the four-character display. Full values can be read with other interfaces.
* Available with PM4, PM8 and PM9 models only
Watlow EZ-ZONE ® PM PID Controller
•
62
•
R: Read
W: Write
E: EEPROM
S: User
Set
Chapter 6 Setup Page
Setup Page
Display
Parameter Name
Description
Range
Default
CIP
Modbus RelaClass
tive
Instance
Address
Attribute
hex (dec)
Profibus
Index
Parameter ID
Data
Type
&
Read/
Write
[`PAr]
[ PAr]
Communications
[none] None (61)
Parity Modbus (1)
[EuEn] Even (191)
Set the parity of this con- [`odd] Odd (192)
troller to match the parity
of the serial network.
None
Instance 1
0x96 (150)
1
Map 1 Map 2
4
2486 2966
----
17003
uint
RWE
[`C_f]
[ C_F]
Communications (1)
Temperature Units
Select whether this communications channel
will display in Celsius or
Fahrenheit.
[```f] Fahrenheit (30)
[```C] Celsius (15)
F
Instance 1
0x96 (150)
Map 1 Map 2
1
2490 2970
6
----
17050
uint
RWE
[Lohi] Low-High (1331)
[hiLo] High-Low (1330)
Low-High
Instance 1
0x96 (150)
1
Map 1 Map 2
5
2488 2968
----
17043
uint
RWE
----
17059
Note:
Applies to Modbus only.
[M;hL]
[M.hL]
Communications (1)
Modbus Word Order
Select the word order of
the two 16-bit words in
the floating-point values.
[Map]
[ Map]
Communications (1)
1 to 2
Data Map
If set to 1 the control will
use PM legacy mapping.
If set to 2 the control will
use new mapping to accommodate new functions.
If 9th digit of part
number
is a 1, 2,
3 or D.
[`nU;S]
[ nV.S]
Communications (1)
[`yes] Yes (106)
Non-volatile Save
[``no] No (59)
If set to Yes all values
written to the control will
be saved in EEPROM.
Yes
Instance 1
0x96 (150)
1
Map 1 Map 2
8
2494 2974
198
17051
uint
RWE
----
----
----
[rtC]*
[`SEt]
Real Time Clock Menu
[hoUr]
[hoUr]
Real Time Clock
Hours
0 to 23
0
Instance 1
Map 1 Map 2
----
4004
88 (136)
1
3
----
36003
uint
RW
[Min]
[Min]
Real Time Clock
Minutes
0 to 59
0
Instance 1
Map 1 Map 2
----
4006
88 (136)
1
4
----
36004
uint
RW
[dow]
[doW]
Real Time Clock
Day of Week
[`sun] Sunday (1565)
[mon] Monday (1559)
[`tue] Tuesday (1560)
[wed] Wednesday (1561)
[thUr] Thursday (1562)
[`fri] Friday (1563)
[`sat] Saturday (1564)
Sun
Instance 1
Map 1 Map 2
----
4002
88 (136)
1
2
----
36002
uint
RW
Note:
Some values will be rounded off to fit in the four-character display. Full values can be read with other interfaces.
* Available with PM4, PM8 and PM9 models only
Watlow EZ-ZONE ® PM PID Controller
•
63
•
R: Read
W: Write
E: EEPROM
S: User
Set
Chapter 6 Setup Page
7
Chapter 7: Profiling Page
Navigating the Profiling Page
Note:
Some of these menus and parameters may not appear, depending on the controller's options. See model
number information in the Appendix for more information. If there is only one instance of a menu, no submenus will appear.
How to Start a Profile
The Profiling Page allows you to enter your ramp
and soak profile information.
After defining the profile follow the steps below to
run the profile:
1. From the Home Page push the Advance Key ‰
repeatedly until Profile Start [P;St1] appears in
the lower display.
2. Use the Up ¿ or Down ¯ key to choose the file
or step number within a profile where you want
the profile to begin running.
3. Press the Advance Key ‰. This takes you to
Profile Action [P;AC1], where you can select the
appropriate action.
• [none] No action
• [ProF] Begin execution from first step of the
specified profile number, whether it exists or not.
• [PAUS] Pause the currently running profile.
• [rESU] Resume running the profile from the
previously paused step.
• [`End] End the profile.
• [StEP] Begin running the profile from the specified step number.
To go to the Profiling Page from the Home Page,
press the Advance Key ‰ for three seconds, until
[ProF] appears in the lower display and the profile
number appears in the upper display. Press the Up
¿ or Down ¯ key to change to another profile.
• Press the Advance Key ‰ to move to the selected
profile's first step.
• Press the Up ¿ or Down ¯ keys to move
through the steps.
• Press the Advance Key ‰ to move through the
selected step's settings.
• Press the Up ¿ or Down ¯ keys to change the
step's settings.
• Press the Infinity Key ˆ at any time to return
to the step number prompt.
• Press the Infinity Key ˆ again to return to the
profile number prompt.
• From any point press and hold the Infinity Key
ˆ for two seconds to return to the Home Page.
Note:
Changes made to profile parameters in the Profiling Pages will be saved and will also have an immediate impact on the running profile. Some parameters in the Profile Status Menu can be changed for the currently running profile, but should only be changed by knowledgeable personnel and with cau-
tion. Changing parameters via the Profile Status Menu will not change the stored profile but will have an immediate im-
pact on the profile that is running.
Profiling Parameters
[``p1] to [``p4]
[prof]
[```1] to [``10]
[``P1]
[s;typ] Step Type
[t;SP1] Target Set Point Loop 1
[hoUr] Hours
[Min] Minutes
[`SEC] Seconds
[RATE] Rate
[W;P1] Wait For Process 1
[w;E1] Wait For Event 1
Watlow EZ-ZONE ® PM PID Controller
•
Note:
Avoid continuous writes within loops. Excessive writes to
EEPROM will cause premature EEPROM failure. The EEPROM is rated for 1,000,000 writes. (To disable EEPROM
writes, go to the Setup Page and then the [Com] menu.
Proceed to the [`nU;s] prompt and set it to no for [Com]
1, 2 or both.)
[WE;2] Wait for Event 2
[dow] Day of Week
[``js] Jump Step
[``jC] Jump Count
[`EnD] End Type
[Ent1] Event 1
[Ent2] Event 2
64
•
Chapter 7 Profiling Page
Profiling Page
Display
Parameter Name
Description
Range
Default
Modbus
Relative Address
----
----
CIP
Class
ParamInstance
eter ID
Attribute
hex (dec)
Data
Type
&
Read/
Write
[``P1]
[prof]
Profiling Menu
[``p1] Step
Select a step to edit or view.
[ P1] to
[``p4]
[ P4]
[S;typ]
[S.typ]
[t;SP1]
[t.SP1]
1 to 10 [profile 1]
11 to 20 [profile 2]
21 to 30 [profile 3]
31 to 40 [profile 4]
[UStP] Unused Step (50)
[`End] End (27)
[``JL] Jump Loop (116)
Note:
[CloC] Wait For Time (1543)
When configuring the profile
type there will be a Time
[W;bo] Wait For Both (210)
prompt as delivered from the
[W;Pr] Wait For Process (209)
factory (default). If rate is
[`W;E] Wait For Event (144)
desired navigate to the Setup
[SoAH] Soak (87)
Page and then the Global Menu
[``ti] Time (143)
where Ramping Type can be
[rate] Rate (81)
changed.
Step Type
Select a step type.
Step Type Parameters
Target Set Point (loop 1)
Select the set point for this
step.
-1,999.000 to 9,999.000°F or
units
-1,128 to 5,537.000°C
Unused
----
Instance 1
0x79 (121)
1 to 40
Map 1 Map 2
1
2570 4500
----
----
21001
uint
RWE
21002
float
RWE
21003
uint
RWE
21004
uint
RWE
21005
uint
RWE
Offset to next
instance (Map
1 equals +50,
Map 2 equals
+100)
0.0°F or
units
-18°C
Instance 1
0x79 (121)
1 to 40
Map 1 Map 2
2
2572 4502
Offset to next
instance (Map
1 equals +50,
Map 2 equals
+100)
[hoUr]
[hoUr]
Step Type Parameters
Hours
Select the hours (plus Minutes
and Seconds) for a timed step.
0 to 99
0
Instance 1
0x79 (121)
1 to 40
Map 1 Map 2
3
2574 4504
Offset to next
instance (Map
1 equals +50,
Map 2 equals
+100)
[Min]
[Min]
Step Type Parameters
Minutes
Select the minutes (plus Hours
and Seconds) for a timed step.
0 to 59
0
Instance 1
0x79 (121)
1 to 40
Map 1 Map 2
4
2576 4506
Offset to next
instance (Map
1 equals +50,
Map 2 equals
+100)
[~SEC]
[ SEC]
Step Type Parameters
Seconds
Select the seconds (plus Hours
and Minutes) for a timed step.
0 to 59
0
Instance 1
0x79 (121)
1 to 40
Map 1 Map 2
5
2578 4508
Offset to next
instance (Map
1 equals +50,
Map 2 equals
+100)
Note:
Some values will be rounded off to fit in the four-character display. Full values can be read with other interfaces.
Watlow EZ-ZONE ® PM PID Controller
•
65
•
R: Read
W: Write
E: EEPROM
S: User Set
Chapter 7 Profiling Page
Profiling Page
Display
[rate]
[rAtE]
W;P1]
[W.P1]
Parameter Name
Description
Range
Default
Step Type Parameters
Rate
Select the rate for ramping in
degrees or units per minute.
0 to 9,999.000°F or units per
minute
0 to 5,555.000°C per minute
Step Type Parameters
Wait For Process Value
Select which analog input Wait
For Process will use.
-1,999.000 to 9,999.000°F or
units
-1,128.000 to 5,537.000°C
0.0
Modbus
Relative Address
CIP
Class
ParamInstance
eter ID
Attribute
hex (dec)
Instance 1
0x79 (121)
Map 1 Map 2
1 to 40
2580 4510
6
Data
Type
&
Read/
Write
21006
float
RWE
21011
float
RWE
21009
uint
RWE
21010
uint
RWE
21041
uint
RWE
21012
uint
RWE
Offset to next
instance (Map
1 equals +50,
Map 2 equals
+100)
0.0°F or
units
-18.0°C
Instance 1
0x79 (121)
1 to 40
Map 1 Map 2
2590 4520 0xB (11)
Offset to next
instance (Map
1 equals +50,
Map 2 equals
+100)
WE;1]
[WE.1]
[WE;2]
[WE.2]
[dow]
[dow]
[~~JS]
[ JS]
[`oFF] Off (62)
Step Type Parameters
Wait Event (5-6)
[``on] On (63)
Select the event state that
[nonE] None (61)
must be satisfied during this
step. Digital input 5 provides
the state of Event 1, and digital
input 6 provides the state of
Event 2.
Off
[`oFF] Off (62)
Step Type Parameters
Wait Event (5-6)
[``on] On (63)
Select the event state that
[nonE] None (61)
must be satisfied during this
step. Digital input 5 provides
the state of Event 1, and digital
input 6 provides the state of
Event 2.
Off
Step Type Parameters
Day of Week
Step Type Parameters
Jump Step
Select a step to jump to.
Instance 1
0x79 (121)
1 to 40
Map 1 Map 2
9
2586 4516
Offset to next
instance (Map
1 equals +50,
Map 2 equals
+100)
Instance 1
0x79 (121)
1 to 40
Map 1 Map 2
2588 4518 0xA (10)
Offset to next
instance (Map
1 equals +50,
Map 2 equals
+100)
[``ed] Every Day (1567)
[`wd] Week days (1566)
[`sun] Sunday (1565)
[mon] Monday (1559)
[`tue] Tuesday (1560)
[wed] Wednesday (1561)
[thUr] Thursday (1562)
[`fri] Friday (1563)
[`sat] Saturday (1564)
Sunday
1 to 40
0
Instance 1
0x79 (121)
1 to 40
Map 1 Map 2
----
4580 0x29 (41)
Offset to next
instance Map 2
equals +100)
Instance 1
0x79 (121)
1 to 40
Map 1 Map 2
2592 4522 0xC (12)
Offset to next
instance (Map
1 equals +50,
Map 2 equals
+100)
Note:
Some values will be rounded off to fit in the four-character display. Full values can be read with other interfaces.
Watlow EZ-ZONE ® PM PID Controller
•
66
•
R: Read
W: Write
E: EEPROM
S: User Set
Chapter 7 Profiling Page
Profiling Page
Display
[~~JC]
[ JC]
[~End]
[ End]
Ent1]
[Ent1]
[Ent2]
[Ent2]
Parameter Name
Description
Range
Default
0 to 9,999
Step Type Parameters
Jump Count
Set the number of jumps. A value of 0 creates an infinite loop.
Loops can be nested four deep.
0
Modbus
Relative Address
CIP
Class
ParamInstance
eter ID
Attribute
hex (dec)
Instance 1
0x79 (121)
1 to 40
Map 1 Map 2
2594 4524 0xD (13)
21013
uint
RWE
21014
uint
RWE
21007
uint
RWE
21008
uint
RWE
Offset to next
instance (Map
1 equals +50,
Map 2 equals
+100)
[`oFF] Control Mode set to Off Off
(62)
[Hold] Hold last closed-loop set
point in the profile (47)
[USEr] User, reverts to previous set point (100)
Instance 1
0x79 (121)
1 to 40
Map 1 Map 2
0xE
(14)
2596 4526
Step Type Parameters
Profile Event Output (A)
Select whether Event Output
1 or 2 is on or off during this
step.
[`oFF] Off (62)
[``on] On (63)
Instance 1
0x79 (121)
1 to 40
Map 1 Map 2
7
2582 4512
Step Type Parameters
Profile Event Output (B)
Select whether Event Output
1 or 2 is on or off during this
step.
[`oFF] Off (62)
[``on] On (63)
Step Type Parameters
End Type
Select what the controller will do
when this profile ends.
Data
Type
&
Read/
Write
Off
Offset to next
instance (Map
1 equals +50,
Map 2 equals
+100)
Offset to next
instance (Map
1 equals +50,
Map 2 equals
+100)
Off
Offset to next
instance (Map
1 equals +50,
Map 2 equals
+100)
Note:
Some values will be rounded off to fit in the four-character display. Full values can be read with other interfaces.
Watlow EZ-ZONE ® PM PID Controller
Instance 1
0x79 (121)
1 to 40
Map 1 Map 2
8
2584 4514
•
67
•
R: Read
W: Write
E: EEPROM
S: User Set
Chapter 7 Profiling Page
8
Chapter 8: Factory Page
Navigating the Factory Page
To go to the Factory Page from the Home Page,
press and hold both the Advance ‰ and Infinity ˆ
keys for six seconds.
• Press the Advance Key ‰ to enter the menu of
choice.
• If a submenu exists (more than one instance),
press the Up ¿ or Down ¯ key to select and then
press the Advance Key ‰ to enter.
• Press the Up ¿ or Down ¯ key to move through
available menu prompts.
• Press the Infinity Key ˆ to move backwards
through the levels: parameter to submenu; submenu to menu; menu to Home Page.
• Press and hold the Infinity Key ˆ for two seconds
to return to the Home Page.
Note:
Some of these menus and parameters may not appear, depending on the controller's options. See model
number information in the Appendix for more information. If there is only one instance of a menu, no submenus will appear.
[CUSt]
[FCty] Custom Setup Menu
[```1] to [``20]
[CUSt] Custom Setup
[`par] Parameter
[`iid] Instance ID
[ELi;o]
[ELi;S]
[ELo;o]
[ELi;s]
Electrical
Electrical
Electrical
Electrical
Input Offset
Input Slope
Output Offset
Output Slope
[`LoC]
[FCty] Security Setting Menu
[`LoC] Security Setting
[LoC;o] Operations Page
[LoC;P] Profiling Page
[pas;e] Password Enable
[RloC] Read Lock
[SLoC] Write Security
[loC;l] Locked Access Level
[roll] Rolling Password
[pas;u] User Password
[pas;a] Administrator Password
[ULoC]
[FCty] Security Setting Menu
[Code] Public Key
[Pass] Password
[diAg]
[FCty] Diagnostics Menu
[diAg] Diagnostics
[``Pn] Part Number
[`rEu] Software Revision
[S;bld] Software Build Number
[``Sn] Serial Number
[dAtE] Date of Manufacture
[`CAL]
[FCty] Calibration Menu
[```1] to [```2]
[`Cal] Calibration
[`Mu] Electrical Measurement
Watlow EZ-ZONE ® PM PID Controller
•
68
•
Chapter 8 Factor y Page
Factory Page
Display
Parameter Name
Description
Range
Default
Modbus
Relative Address
CIP
Data
Class
Type
Profibus ParamInstance
&
Index eter ID
Attribute
Read/
hex (dec)
Write
[Cust]
[fcty]
Custom Menu
[`par]
[ Par]
Custom
Parameter 1 to 20
Select the parameters that
will appear in the Home
Page.
The Parameter 1 value will
appear in the upper display of the Home Page. It
cannot be changed with
the Up and Down Keys
in the Home Page.
The Parameter 2 value will
appear in the lower display in the Home Page. It
can be changed with the
Up and Down Keys, if the
parameter is a writable
one.
Scroll through the other
Home Page parameters
with the Advance Key
‰.
[`iid]
[ iid]
Custom (1 to 20)
Instance ID
Select which instance of
the parameter will be selected.
[nonE] None
[gSd1] Guaranteed Soak
Deviation 1 Value
[P;ACr] Profile Action Request
[P;Str] Profile Start
[idLE] Idle Set Point
[t;tUn] TRU-TUNE+® Enable
[`r;rt] Ramp Rate
[`C;hy] Cool Hysteresis
[`C;Pb] Cool Proportional
Band
[`h;hy] Heat Hysteresis
[`h;Pb] Heat Proportional
Band
[``db] Dead Band
[``td] Time Derivative
[``ti] Time Integral
[`C;Pr] Cool Power
[`h;Pr] Heat Power
[`C;M] User Control Mode
[`AUt] Autotune
[``op] Open Loop Set
Point
[AC;SP] Active Set Point
[AC;pu] Active Process
Value
[StPt] Set Point
CUSt] Custom Menu
[`A;hy] Alarm Hysteresis
[`A;hi] Alarm High Set
Point
[`A;Lo] Alarm Low Set
Point
[USr;r] User Restore Set
[`C_F] Display Units
[`i;CA] Input Calibration
Offset
[`Pro] Process
See:
Home
Page
----
----
----
14005
uint
RWES
----
----
----
----
14003
uint
RWES
----
----
----
3002
uint
RWE
1 to 4
[`LoC]
[FCty]
Security Setting Menu
[LoC;o]
[LoC.o]
Security Setting
Operations Page
Change the security level
of the Operations Page.
1 to 3
2
Note:
Some values will be rounded off to fit in the four-character display. Full values can be
read with other interfaces.
R: Read
W: Write
E: EEPROM
S: User
If there is only one instance of a menu, no submenus will appear.
Set
Watlow EZ-ZONE ® PM PID Controller
•
69
•
Chapter 8 Factor y Page
Factory Page
Display
Parameter Name
Description
Range
Default
Modbus
Relative Address
CIP
Data
Class
Type
Profibus ParamInstance
&
Index eter ID
Attribute
Read/
hex (dec)
Write
[LoC;P]
[LoC.P]
Security Setting
Profiling Page
Change the security level
of the Profiling Page.
1 to 3
3
----
----
----
3008
uint
RWE
[pas;e]
[LoC.P]
Security Setting
Password Enable
Turn security features on
or off.
[`off] Off
[``on] On
Off
----
----
----
3009
uint
RWE
[rLoC]
[rLoC]
Security Setting
Read Lock
Set the read security
clearance level. The user
can access the selected
level and all lower levels.
If the Set Lockout Security
level is higher than the
Read Lockout Security,
the Read Lockout Security level takes priority.
1 to 5
5
----
----
----
3010
uint
RWE
[SLoC]
[SLoC]
Security Setting
Write Security
Set the write security
clearance level. The user
can access the selected
level and all lower levels.
If the Set Lockout Security
level is higher than the
Read Lockout Security,
the Read Lockout Security level takes priority.
0 to 5
5
----
----
----
3011
uint
RWE
[loC;l]
[LoC.L]
Security Setting
Locked Access Level
Determines user level
menu visibility when
security is enabled. See
Features section under
Password Security.
1 to 5
5
----
----
----
3016
uint
RWE
[roll]
[roLL]
Security Setting
Rolling Password
When power is cycled a
new Public Key will be
displayed.
[`off] Off
[``on] On
Off
----
----
----
3019
uint
RWE
[pas;u]
[PAS.u]
Security Setting
User Password
Used to acquire access
to menus made available
through the Locked Access
Level setting.
10 to 999
63
----
----
----
3017
uint
RWE
[pas;a]
[PAS.A]
Security Setting
Administrator Password
Used to acquire full access
to all menus.
10 to 999
156
----
----
----
3018
uint
RWE
Note:
Some values will be rounded off to fit in the four-character display. Full values can be
read with other interfaces.
R: Read
W: Write
E: EEPROM
S: User
If there is only one instance of a menu, no submenus will appear.
Set
Watlow EZ-ZONE ® PM PID Controller
•
70
•
Chapter 8 Factor y Page
Factory Page
Display
Parameter Name
Description
Range
Default
Modbus
Relative Address
CIP
Data
Class
Type
Profibus ParamInstance
&
Index eter ID
Attribute
Read/
hex (dec)
Write
[ULoC]
[FCty]
Security Setting Menu
[Code]
[CodE]
Security Setting
Customer Specific
Public Key
If Rolling Password turned
on, generates a random
number when power is
cycled. If Rolling Password
is off fixed number will be
displayed.
0
----
----
----
3020
uint
R
[pass]
[PASS]
Security Setting
Password
Number returned from
calculation found in Features section under Password Security.
0
----
----
----
3022
int
RW
-1999 to 9999
[diag]
[fcty]
Diagnostics Menu
[``Pn]
[ Pn]
Diagnostics
Part Number
Display this controller's
part number.
15 characters
----
----
0x65
(101)
1
9
115
1009
string
RWE
[`rEu]
[ rEu]
Diagnostics
Software Revision
Display this controller's
firmware revision number.
1 to 10
----
----
0x65
(101)
1
0x11 (17)
116
1003
string
R
[S;bLd]
[S.bLd]
Diagnostics
Software Build Number
Display the firmware
build number.
0 to 2,147,483,647
----
Instance 1
Map 1 Map 2
8
8
0x65
(101)
1
5
----
1005
dint
R
[``Sn]
[ Sn]
Diagnostics
Serial Number
Display the serial number.
0 to 2,147,483,647
----
----
0x65
(101)
1
0x20 (32)
----
1032
string
RWE
[dAtE]
[dAtE]
Diagnostics
Date of Manufacture
Display the date code.
0 to 2,147,483,647
----
Instance 1
Map 1 Map 2
14 14
0x65
(101)
1
8
----
1008
dint
RWE
-3.4e38 to 3.4e38
----
Instance 1
Map 1 Map 2
400 400
Instance 2
Map 1 Map 2
480 490
0x68
(104)
1 to 2
0x15 (21)
----
4021
float
R
[`CAL]
[FCty]
Calibration Menu
[`Mu] Calibration (1 to 2)
Electrical Measurement
[ Mv]
Read the raw electrical
value for this input in the
units corresponding to
the Sensor Type (Setup
Page, Analog Input Menu)
setting.
Note:
Some values will be rounded off to fit in the four-character display. Full values can be
read with other interfaces.
R: Read
W: Write
E: EEPROM
S: User
If there is only one instance of a menu, no submenus will appear.
Set
Watlow EZ-ZONE ® PM PID Controller
•
71
•
Chapter 8 Factor y Page
Factory Page
Modbus
Relative Address
CIP
Data
Class
Type
Profibus ParamInstance
&
Index eter ID
Attribute
Read/
hex (dec)
Write
Display
Parameter Name
Description
[ELi;o]
[ELi.o]
Calibration (1 to 2)
Electrical Input Offset
Change this value to calibrate the low end of the
input range.
-1,999.000 to 9,999.000
0.0
Instance 1
Map 1 Map 2
378 378
Instance 2
Map 1 Map 2
458 468
0x68
(104)
1 to 2
0xA (10)
----
4010
float
RWES
[ELi;S]
[ELi.S]
Calibration (1 to 2)
Electrical Input Slope
Adjust this value to calibrate the slope of the input value.
-1,999.000 to 9,999.000
1.0
Instance 1
Map 1 Map 2
380 380
Instance 2
Map 1 Map 2
460 470
0x68
(104)
1 to 2
0xB (11)
----
4011
float
RWES
[ELo;o]
[ELo.o]
Calibration (1 or 3)
Electrical Output Offset
Change this value to calibrate the low end of the
output range.
Menu 2 calibrates output
3.
-1,999.000 to 9,999.000
0.0
----
----
----
18005
----
[ELo;S]
[ELo.S]
Calibration (1 or 3)
Electrical Output Slope
Adjust this value to calibrate the slope of the output value.
Menu 2 calibrates output
3.
-1,999.000 to 9,999.000
1.0
----
----
----
18006
----
Range
Default
Note:
Some values will be rounded off to fit in the four-character display. Full values can be
read with other interfaces.
R: Read
W: Write
E: EEPROM
S: User
If there is only one instance of a menu, no submenus will appear.
Set
Watlow EZ-ZONE ® PM PID Controller
•
72
•
Chapter 8 Factor y Page
9
Chapter 9: Features
Saving and Restoring User Settings. . . . . . . . . . . . . . . . . . . . . . . . . . 74
Programming the Home Page. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74
Tuning the PID Parameters. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74
Manual Tuning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
Autotuning with TRU‑TUNE+®. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
Inputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76
Calibration Offset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76
Calibration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76
Filter Time Constant. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
Set Point Low Limit and High Limit. . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
Scale High and Scale Low . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
Range High and Range Low. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
Outputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
Duplex . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
NO-ARC Relay . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78
Retransmitting a Process Value or Set Point. . . . . . . . . . . . . . . . . . . . . 78
Cool Output Curve . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78
Control Methods. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79
Output Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79
Auto (closed loop) and Manual (open loop) Control . . . . . . . . . . . . . . . 79
On-Off Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80
Proportional Control. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80
Proportional plus Integral (PI) Control. . . . . . . . . . . . . . . . . . . . . . . . . . 80
Proportional plus Integral plus Derivative (PID) Control . . . . . . . . . . . . 81
Dead Band . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81
Variable Time Base. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81
Single Set Point Ramping. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82
Alarms. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82
Process and Deviation Alarms. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82
Alarm Set Points. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82
Alarm Hysteresis . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83
Alarm Latching. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83
Alarm Silencing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83
Alarm Blocking. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83
Open Loop Detection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83
Programming the EZ Key/s. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84
Using Lockout to Hide Pages and Menus . . . . . . . . . . . . . . . . . . . . . . 84
Using Password Security . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85
Modbus - Using Programmable Memory Blocks . . . . . . . . . . . . . . . . . 86
Software Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87
Watlow EZ-ZONE ® PM PID Controller
•
73
•
Chapter 9 Features
Saving and Restoring User Settings
Recording setup and operations parameter settings
for future reference is very important. If you unintentionally change these, you will need to program the
correct settings back into the controller to return the
equipment to operational condition.
After you program the controller and verify proper operation, use User Save Set [USr;S] (Setup Page,
Global Menu) to save the settings into either of two
files in a special section of memory. If the settings in
the controller are altered and you want to return the
controller to the saved values, use User Restore Set
[USr; r] (Setup Page, Global Menu) to recall one of
the saved settings.
A digital input or the Function Key can also be
configured to restore parameters.
Note:
Only perform the above procedure when you are
sure that all the correct settings are programmed
into the controller. Saving the settings overwrites
any previously saved collection of settings. Be sure
to document all the controller settings.
Programming the Home Page
Watlow’s patented user-defined menu system improves operational efficiency. The user-defined Home
Page provides you with a shortcut to monitor or
change the parameter values that you use most often.
You can create your own Home Page with as
many as 20 of the active parameters. When a parameter normally located in the Setup Page or Operations Page is placed in the Home Page, it is accessible through both. If you change a parameter in the
Home Page, it is automatically changed in its original page. If you change a parameter in its original
page it is automatically changed in the Home Page.
The default parameters will automatically appear
in the Home Page.
Change the list of parameters in the Home Page
from the Custom Menu [CUSt] (Factory Page).
after an autotune has been started has no affect.
A new feature in EZ-ZONE PM products will allow set point changes while the control is autotuning, this includes while running a profile or ramping.
When the auto tune is initially started it will use
the current set point and will disregard all set point
changes until the tuning process is complete. Once
complete, the controller will then use the new set
point.
This is why it is a good idea to enter the active set
point before initiating an autotune.
Autotuning calculates the optimum heating and/
or cooling PID parameter settings based on the system's response. Autotuning can be enabled whether
or not TUNE-TUNE+ ® is enabled. The PID settings
generated by the autotune will be used until the autotune feature is rerun, the PID values are manually
adjusted or TRU-TUNE+® is enabled.
To initiate an autotune, set Autotune Request
[`AUt] (Operations Page, Loop Menu) to [`YES].
You should not autotune while a profile is running. If
the autotune cannot be completed in 60 minutes, the
autotune will time-out and the original settings will
take effect.
The lower display will flash between [tUnE] and
the set point while the autotuning is underway. The
temperature must cross the Autotune Set Point five
times to complete the autotuning process. Once complete, the controller controls at the normal set point,
using the new parameters.
Select a set point for the tune with Autotune Set
Point. The Autotune Set Point is expressed as a percent of the Closed Loop Set Point.
If you need to adjust the tuning procedure's aggressiveness, use Autotune Aggressiveness [T;Agr]
(Setup Page, Loop Menu). Select under damped 
[Undr] to bring the process value to the set point
quickly. Select over damped [ouer] to bring the process value to the set point with minimal overshoot.
Select critical damped [Crit] to balance a rapid response with minimal overshoot.
Process Set Point
Autotune begins
Autotune complete
Tuning the PID Parameters
Autotuning
When an autotune is performed on the EZ-ZONE
PM, the set point is used to calculate the tuning set
point.
For example, if the active set point is 200° and
Autotune Set Point [A;tSP] (Operations Page, Loop
Menu) is set to 90 percent, the autotune function
utilizes 180° for tuning. This is also how autotuning works in previous Watlow Winona controllers. In
addition, changing the active set point in previous
controllers causes the autotune function to restart;
where with the EZ-ZONE PM changing the set point
Wat low EZ-ZONE ® PM PID Controller
•
Temperature
Autotune Set Point
(90 percent of Process Set Point)
Time
74
•
Chapter 9 Features
Manual Tuning
In some applications, the autotune process may not
provide PID parameters for the process characteristics you desire. If that is the case, you may want to
tune the controller manually.
1. Apply power to the controller and establish a set
point typically used in your process.
2. Go to the Operations Page, Loop Menu, and set
Heat Proportional Band [`h;Pb] and/or Cool Proportional Band [`C;Pb] to 5. Set Time Integral
[``ti] to 0. Set Time Derivative [``td] to 0.
3. When the system stabilizes, watch the process
value. If it fluctuates, increase the Heat Proportional Band or Cool Proportional Band value in 3
to 5° increments until it stabilizes, allowing time
for the system to settle between adjustments.
4. When the process has stabilized, watch Heat
Power [`h;Pr] or Cool Power [`C;Pr] (Operations
Page, Monitor Menu). It should be stable ±2%. At
this point, the process temperature should also
be stable, but it will have stabilized before reaching the set point. The difference between the set
point and actual process value can be eliminated
with Integral.
5. Start with an Integral value of 6,000 and allow
10 minutes for the process temperature to reach
the set point. If it has not, reduce the setting by
half and wait another 10 minutes. Continue reducing the setting by half every 10 minutes until
the process value equals the set point. If the process becomes unstable, the Integral value is too
small. Increase the value until the process stabilizes.
6. Increase Derivative to 0.1. Then increase the set
point by 11° to 17°C. Monitor the system’s approach to the set point. If the process value overshoots the set point, increase Derivative to 0.2.
Increase the set point by 11° to 17°C and watch
the approach to the new set point. If you increase
Derivative too much, the approach to the set
point will be very sluggish. Repeat as necessary
until the system rises to the new set point without overshoot or sluggishness.
For additional information about autotune and PID
control, see related features in this chapter.
Autotuning with TRU‑TUNE+®
The TRU-TUNE+® adaptive algorithm will optimize
the controller's PID values to improve control of dynamic processes. TRU-TUNE+ ® monitors the process
variable and adjusts the control parameters automatically to keep your process at set point during set
point and load changes. When the controller is in the
adaptive control mode, it determines the appropriate
output signal and, over time, adjusts control parameters to optimize responsiveness and stability. The
TRU-TUNE+ ® feature does not function for on-off
control.
Watlow EZ-ZONE ® PM PID Controller
•
The preferred and quickest method for tuning a
loop is to establish initial control settings and continue with the adaptive mode to fine tune the settings.
Setting a controller's control mode to tune starts
this two-step tuning process. (See Autotuning in this
chapter.) This predictive tune determines initial,
rough settings for the PID parameters. Then the loop
automatically switches to the adaptive mode which
fine tunes the PID parameters.
Once the process variable has been at set point for
a suitable period (about 30 minutes for a fast process
to roughly two hours for a slower process) and if no
further tuning of the PID parameters is desired or
needed, TRU‑TUNE+® may be turned off. However,
keeping the controller in the adaptive mode allows it
to automatically adjust to load changes and compensate for differing control characteristics at various
set points for processes that are not entirely linear.
Once the PID parameters have been set by the
TRU‑TUNE+ ® adaptive algorithm, the process, if
shut down for any reason, can be restarted in the
adaptive control mode.
Turn TRU‑TUNE+® on or off with TRU‑TUNE+®
Enable [t;tUn] (Setup Page, Loop Menu).
Use TRU‑TUNE+ ® Band [t;bnd] (Setup Page,
Loop Menu) to set the range above and below the
set point in which adaptive tuning will be active.
Adjust this parameter only in the unlikely event
that the controller is unable to stabilize at the set
point with TRU‑TUNE+ ® Band set to auto (0). This
may occur with very fast processes. In that case, set
TRU‑TUNE+™ Band to a large value, such as 100.
Use TRU‑TUNE+ ® Gain [`t;gn] (Setup Page,
Loop Menu) to adjust the responsiveness of the adaptive tuning calculations. Six settings range from 1,
with the most aggressive response and most potential overshoot (highest gain), to 6, with the least aggressive response and least potential for overshoot
(lowest gain). The default setting, 3, is recommended
for loops with thermocouple feedback and moderate
response and overshoot potential.
Before Tuning
Before autotuning, the controller hardware must be
installed correctly, and these basic configuration parameters must be set:
• Sensor Type [`SEn] (Setup Page, Analog Input
Menu), and scaling, if required;
• Function [``Fn] (Setup Page, Output Menu) and
scaling, if required.
How to Autotune a Loop
1. Enter the desired set point or one that is in the
middle of the expected range of set points that
you want to tune for.
2. Enable TRU-TUNE+ ®.
3. Initiate an autotune. (See Autotuning in this
chapter.)
75
•
Chapter 9 Features
When autotuning is complete, the PID parameters
should provide good control. As long as the loop is in
the adaptive control mode, TRU-TUNE+ ® continuously tunes to provide the best possible PID control
for the process.
ç
WARNING! During autotuning, the controller sets the output
to 100 percent and attempts to drive the process variable
toward the set point. Enter a set point and heat and cool
power limits that are within the safe operating limits of your
system.
Inputs
Calibration Offset
Calibration offset allows a device to compensate for
an inaccurate sensor, lead resistance or other factors
that affect the input value. A positive offset increases
the input value, and a negative offset decreases the
input value.
The input offset value can be viewed or changed
with Calibration Offset [`i;CA] (Operations Page,
Analog Input Menu).
Negative Calibration Offset will
compensate for the difference
between the Sensor Reading and
the Actual Temperature
Temperature
Temperature Reading
from Sensor
Actual Process Temperature
Time
Calibration
To calibrate an analog input, you will need to provide
two electrical signals or resistance loads near the extremes of the range that the application is likely to
utilize. See recommended values below:
Sensor Type
Low Source
High Source
thermocouple
0.000 mV
50.000 mV
millivolts
0.000 mV
50.000 mV
volts
0.000V
10.000V
milliamps
0.000 mA
20.000 mA
100 Ω RTD
50.00 Ω
350.00 Ω
1,000 Ω RTD
500.00 Ω
3,500.00 Ω
Thermistor 5K
50.00 Ω
5000.00 Ω
Thermistor 10K
50.00 Ω
10000.00 Ω
Thermistor 20K
50.00 Ω
20000.00 Ω
Thermistor 40K
50.00 Ω
40000.00 Ω
Wat low EZ-ZONE ® PM PID Controller
Follow these steps for a thermocouple or process input:
1.Apply the low source signal to the input you are
calibrating. Measure the signal to ensure it is accurate.
2.Read the value of Electrical Measurement [`Mu]
(Factory Page, Calibration Menu) for that input.
3.Calculate the offset value by subtracting this value from the low source signal.
4.Set Electrical Input Offset [ELi;o] (Factory Page,
Calibration Menu) for this input to the offset value.
5.Check the Electrical Measurement to see whether
it now matches the signal. If it doesn’t match, adjust Electrical Input Offset again.
6.Apply the high source signal to the input. Measure the signal to ensure it is accurate.
7.Read the value of Electrical Measurement for
that input.
8.Calculate the gain value by dividing the low
source signal by this value.
9.Set Electrical Input Slope [ELi;S] (Factory Page,
Calibration Menu) for this input to the calculated
gain value.
10. Check the Electrical Measurement to see whether it now matches the signal. If it doesn’t match,
adjust Electrical Input Slope again.
Set Electrical Input Offset to 0 and Electrical Input
Slope to 1 to restore factory calibration.
Follow these steps for an RTD input:
1.Measure the low source resistance to ensure it
is accurate. Connect the low source resistance to
the input you are calibrating.
2.Read the value of Electrical Measurement [`Mu]
(Factory Page, Calibration Menu) for that input.
3.Calculate the offset value by subtracting this value from the low source resistance.
4.Set Electrical Input Offset [ELi;o] (Factory Page,
Calibration Menu) for this input to the offset value.
5.Check the Electrical Measurement to see whether
it now matches the resistance. If it doesn’t match,
adjust Electrical Offset again.
6.Measure the high source resistance to ensure it
is accurate. Connect the high source resistance to
the input.
7.Read the value of Electrical Measurement for
that input.
8.Calculate the gain value by dividing the low
source signal by this value.
9.Set Electrical Input Slope [ELi;S] (Factory Page,
Calibration Menu) for this input to the calculated
gain value.
10. Check the Electrical Measurement to see whether it now matches the signal. If it doesn’t match,
adjust Electrical Input Slope again.
Set Electrical Input Offset to 0 and Electrical Input
Slope to 1 to restore factory calibration.
•
76
•
Chapter 9 Features
Filter Time Constant
Scale High and Scale Low
Filtering smoothes an input signal by applying a
first-order filter time constant to the signal. Filtering the displayed value makes it easier to monitor.
Filtering the signal may improve the performance of
PID control in a noisy or very dynamic system.
Adjust the filter time interval with Filter Time
[`FiL] (Setup Page, Analog Input Menu).
Example: With a filter value of 0.5 seconds, if the
process input value instantly changes from 0 to 100
and remained at 100, the display will indicate 100 after
five time constants of the filter value or 2.5 seconds.
When an analog input is selected as process voltage
or process current input, you must choose the value
of voltage or current to be the low and high ends. For
example, when using a 4 to 20 mA input, the scale
low value would be 4.00 mA and the scale high value
would be 20.00 mA. Commonly used scale ranges are:
0 to 20 mA, 4 to 20 mA, 0 to 5V, 1 to 5V and 0 to 10V.
You can create a scale range representing other
units for special applications. You can reverse scales
from high values to low values for analog input signals that have a reversed action. For example, if 50
psi causes a 4 mA signal and 10 psi causes a 20 mA
signal.
Scale low and high low values do not have to match
the bounds of the measurement range. These along
with range low and high provide for process scaling
and can include values not measureable by the controller. Regardless of scaling values, the measured value
will be constrained by the electrical measurements of
the hardware.
Select the low and high values with Scale Low
[`S;Lo] and Scale High [`S;hi]. Select the displayed
range with Range Low [`r;Lo] and Range High
[`r;hi] (Setup Page, Analog Input Menu).
Temperature
Unfiltered Input Signal
Time
Temperature
Filtered Input Signal
Range High and Range Low
Time
Filter Time Constant
Sensor Selection
You need to configure the controller to match the input device, which is normally a thermocouple, RTD or
process transmitter.
Select the sensor type with Sensor Type [`Sen]
(Setup Page, Analog Input Menu).
Set Point Low Limit and High Limit
The controller constrains the set point to a value between a set point low limit and a set point high limit.
Set the set point limits with Low Set Point
[`L;SP] and High Set Point [`h;SP] (Setup Page,
Loop Menu).
There are two sets of set point low and high limits: one for a closed-loop set point, another for an
open-loop set point.
Range High Range (between High Limit of Sensor and Range Low)
Gas Pressure
Outputs
Duplex
Certain systems require that a single process output
control both heating and cooling outputs. An EZZONE PM controller with a process output can function as two separate outputs.
With a 4 to 20mA output the heating output will
operate from 12 to 20mA (0 to +100 percent) and the
cooling output will operate from 12 to 4mA (0 to -100
percent).
In some cases this type of output is required by
the device that the EZ-ZONE PM controls, such as
a three-way valve that opens one way with a 12 to
High Limit of selected functional range
Set Point High
Set Point Range (must be between Range High and Range Low)
Set Point Low
Range Low Range (between Low Limit of Sensor and Range High)
Low Limit of selected functional range
Range Low and Range High
Watlow EZ-ZONE ® PM PID Controller
With a process input, you must choose a value to represent the low and high ends of the current or voltage
range. Choosing these values allows the controller’s
display to be scaled into the actual working units of
measurement. For example, the analog input from a
humidity transmitter could represent 0 to 100 percent relative humidity as a process signal of 4 to 20
mA. Low scale would be set to 0 to represent 4 mA
and high scale set to 100 to represent 20 mA. The indication on the display would then represent percent
humidity and range from 0 to 100 percent with an
input of 4 to 20 mA.
Select the low and high values with Range Low
[`r;Lo] and Range High [`r;hi] (Setup Page, Analog
Input Menu).
•
77
•
Chapter 9 Features
NO-ARC Relay
A NO-ARC relay provides a significant improvement
in the life of the output relay over conventional relays.
Conventional mechanical relays have an expected
life of 100,000 cycles at the rated full-load current.
The shorter life for conventional relays is due to the
fact that when contacts open while current is flowing
metal degradation occurs. This action produces unavoidable electrical arcing causing metal to transfer
from one contact to the other. The arcing conditions
continue on each subsequent contact opening until
over time the resistance through the contacts increases causing the contacts to increase in temperature. Eventually, the contacts will weld together and
the relay remains in the on state.
The Watlow NO-ARC relay is a hybrid relay. It uses a mechanical relay for the current load and a triac
(solid-state switch) to carry the turn-on and turn-off
currents. NO-ARC relays extend the life of the relay
more than two million cycles at the rated full-load
current.
Although a NO-ARC relay has significant life advantages, a few precautions must be followed for acceptable usage:
Do not use:
• hybrid relays for limit contactors. A limit or
safety device must provide a positive mechanical
break on all hot legs simultaneously;
• dc loads with hybrid relays. The triacs used for
arc suppression will turn off only with ac line
voltage;
• hybrid switches to drive any inductive loads, such
as relay coils, transformers or solenoids;
• cycle times less than five seconds on hybrid
switches;
• on loads that exceed 264V ac through relay;
• on loads that exceed 15 amperes load;
• on loads less than 100 mA;
• NO-ARC relays in series with other NO-ARC relays.
put for a chart recorder documenting system performance over time.
In choosing the type of retransmit signal the operator must take into account the input impedance
of the device to be retransmitted to and the required
signal type, either voltage or milliamps.
Typically applications might use the retransmit
option to record one of the variables with a chart recorder or to generate a set point for other controls in
a multi-zone application.
Output 1 can be ordered as process outputs. Select
retransmit [rMt] as the Output Function [``Fn]
(Setup Page, Output Menu). Set the output to volts
[uoLt] or milliamps [`MA] with Output Type
[`o;ty]. Select the signal to retransmit with Retransmit Source [`r;Sr].
Range High
Output Scale
20mA signal and opens the other way with a 4 to
12mA signal. This feature reduces the overall system
cost by using a single output to act as two outputs.
Outputs 1 and 3 can be ordered as process outputs. Select duplex [dUPL] as the Output Function
[``Fn] (Setup Page, Output Menu). Set the output to
volts [uoLt] or milliamps [`MA] with Output Type
[`o;ty]. Set the range of the process output with
Scale Low [`S;Lo] and Scale High [`S;hi].
Range Low
Scale Low
Retransmit Source
Scale High
Retransmit
Set the range of the process
output with Scale
Low [`S;Lo] and Scale High [`S;hi]. Scale the retransmit source to the process output with Range
Low [`r;Lo] and Range High [`r;hi].
When the retransmit source is at the Range Low
value, the retransmit output will be at its Scale Low
value. When the retransmit source is at the Range
High value, the retransmit output will be at its Scale
High value.
Cool Output Curve
A nonlinear output curve may improve performance
when the response of the output device is nonlinear.
If a cool output uses one of the nonlinear curves a
PID calculation yields a lower actual output level
than a linear output would provide.
These output curves are used in plastics extruder
applications: curve 1 for oil-cooled extruders and
curve 2 for water-cooled extruders.
Retransmitting a Process Value or Set Point
The retransmit feature allows a process output to
provide an analog signal that represents the set
point or process value. The signal may serve as a
remote set point for another controller or as an inWat low EZ-ZONE ® PM PID Controller
•
78
•
Chapter 9 Features
is present, the controller will perform closed-loop control. Closed-loop control uses a process sensor to determine the difference between the process value and
the set point. Then the controller applies power to a
control output load to reduce that difference.
If a valid input signal is not present, the controller will indicate an input error message in the upper
display and [Attn] in the lower display and respond
to the failure according to the setting of Input Error
Failure [FAiL]. You can configure the controller to
perform a “bumpless” transfer [bPLS], switch power
to output a preset fixed level [MAn], or turn the output power off.
Bumpless transfer will allow the controller to
transfer to the manual mode using the last power
value calculated in the auto mode if the process had
stabilized at a ±5 percent output power level for the
time interval of Time Integral (Operations Page,
Loop) prior to sensor failure, and that power level is
less than 75 percent.
Actual Output Power
100
80
60
Linear
40
Curve 1
Curve 2
20
0
PID Calculation
Select a nonlinear cool output curve with Cool
Output Curve [`C;Cr] (Setup Menu, Loop Menu).
Control Methods
Output Configuration
Auto (closed loop) and Manual (open loop) Control
The controller has two basic modes of operation, auto
mode and manual mode. Auto mode allows the controller to decide whether to perform closed-loop control or to follow the settings of Input Error Failure
[FAiL] (Setup Page, Loop Menu). The manual mode
only allows open-loop control. The EZ-ZONE PM controller is normally used in the auto mode. The manual mode is usually only used for specialty applications
or for troubleshooting.
Manual mode is open-loop control that allows the
user to directly set the power level to the controller’s
output load. No adjustments of the output power level
occur based on temperature or set point in this mode.
In auto mode, the controller monitors the input to
determine if closed-loop control is possible. The controller checks to make certain a functioning sensor is
providing a valid input signal. If a valid input signal
Watlow EZ-ZONE ® PM PID Controller
•
Sensor
Break
100%
Output Power
40%
Power
Each controller output can be configured as a heat
output, a cool output, an alarm output or deactivated. No dependency limitations have been placed on
the available combinations. The outputs can be configured in any combination. For instance, all three
could be set to cool.
Heat and cool outputs use the set point and Operations parameters to determine the output value. All
heat and cool outputs use the same set point value.
Heat and cool each have their own set of control parameters. All heat outputs use the same set of heat
control parameters and all cool outputs use the same
set of cool output parameters.
Each alarm output has its own set of configuration parameters and set points, allowing independent
operation.
Actual Temperature
Temperature
Set Point
2 minutes
0%
Locks in
Output
Power
Time
Bumpless Transfer
Input Error Latching [`i;Er] (Setup Page, Analog Input Menu) determines the controller’s response
once a valid input signal returns to the controller.
If latching is on, then the controller will continue to
indicate an input error until the error is cleared. To
clear a latched alarm, press the Advance Key ‰ then
the Up Key ¿.
If latching is off, the controller will automatically
clear the input error and return to reading the temperature. If the controller was in the auto mode when
the input error occurred, it will resume closed-loop
control. If the controller was in manual mode when
the error occurred, the controller will remain in
open-loop control.
The Manual Control Indicator Light % is on when
the controller is operating in manual mode.
You can easily switch between modes if the Control Mode [`C;M] parameter is selected to appear in
the Home Page.
To transfer to manual mode from auto mode,
press the Advance Key ‰ until [`C;M] appears in
the lower display. The upper display will display
[AUto] for auto mode. Use the Up ¿ or Down ¯ keys
to select [Man]. The manual set point value will be
recalled from the last manual operation.
To transfer to auto mode from manual mode,
press the Advance Key ‰ until [`C;M] appears in
the lower display. The upper display will display
79
•
Chapter 9 Features
[MAn] for manual mode. Use the Up ¿ or Down ¯
keys to select [AUto]. The automatic set point value
will be recalled from the last automatic operation.
Changes take effect after three seconds or immediately upon pressing either the Advance Key ‰ or
the Infinity Key ˆ.
On-Off Control
On-off control switches the output either full on or
full off, depending on the input, set point and hysteresis values. The hysteresis value indicates the
amount the process value must deviate from the set
point to turn on the output. Increasing the value decreases the number of times the output will cycle.
Decreasing hysteresis improves controllability. With
hysteresis set to 0, the process value would stay closer to the set point, but the output would switch on
and off more frequently, and may result in the output
“chattering.”
On-off control can be selected with Heat Algorithm [`h;Ag] or Cool Algorithm [`C;Ag] (Setup Page,
Loop Menu).
On-off hysteresis can be set with Heat Hysteresis
[`h;hY] or Cool Hysteresis [`C;hY] (Operations Page,
Loop Menu).
Note:
Input Error Failure Mode [faIl] does not function
in on-off control mode. The output goes off.
Proportional Control
Some processes need to maintain a temperature or
process value closer to the set point than on-off control can provide. Proportional control provides closer
control by adjusting the output when the temperature
or process value is within a proportional band. When
the value is in the band, the controller adjusts the
output based on how close the process value is to the
set point.
The closer the process value is to the set point, the
lower the output power. This is similar to backing
off on the gas pedal of a car as you approach a stop
sign. It keeps the temperature or process value from
swinging as widely as it would with simple on-off
control. However, when the system settles down, the
temperature or process value tends to “droop” short
of the set point.
With proportional control the output power level
equals (set point minus process value) divided by the
proportional band value.
In an application with one output assigned to
heating and another assigned to cooling, each will
have a separate proportional parameter. The heating
parameter takes effect when the process temperature
is lower than the set point, and the cooling parameter takes effect when the process temperature is
higher than the set point.
Adjust the proportional band with Heat Proportional Band [`h;Pb] or Cool Proportional Band
[`C;Pb] (Operations Page, Loop Menu).
Temperature
The heating action switches off when the process
temperature rises above the set point.
Set Point
Hysteresis
Process Temperature
The heating action
switches on at startup.
Droop
Proportional Band
Temperature
Set Point
Overshoot
The heating action switches on when the process temperature
drops below the set point minus the hysteresis.
Time
Time
The cooling action switches on when
the process temperature rises above
the set point plus the hysteresis.
The cooling action
switches
on at startup.
Temperature
Proportional Control
Process Temperature
Set Point
Proportional plus Integral (PI) Control
The droop caused by proportional control can be corrected by adding integral (reset) control. When the
system settles down, the integral value is tuned to
bring the temperature or process value closer to the
set point. Integral determines the speed of the correction, but this may increase the overshoot at startup or when the set point is changed. Too much integral action will make the system unstable. Integral
is cleared when the process value is outside of the
proportional band.
Adjust the integral with Time Integral [``ti]
(Operations Page, Loop Menu).
Hysteresis
The cooling action switches off when the process
temperature drops below the set point.
Time
On/Off System Cycles
Wat low EZ-ZONE ® PM PID Controller
•
80
•
Chapter 9 Features
Proportional plus Integral plus Derivative (PID)
Control
Use derivative (rate) control to minimize the overshoot in a PI-controlled system. Derivative (rate) adjusts the output based on the rate of change in the
temperature or process value. Too much derivative
(rate) will make the system sluggish.
Derivative action is active only when the process
value is within twice the proportional value from the
set point.
Adjust the derivative with Time Derivative
[``td] (Operations Page, Loop Menu).
Temperature
Heat Output Active
Zero Dead Band
Time
When the dead band value is a negative value, both heating and cooling outputs are active when
the temperature is near the set point.
Reduced Overshoot
Set Point
Cool Output Active
Set Point
Proportional Band
Heating Slows
Cool Output Active
Set Point
Heat Output Active
Temperature
Temperature
Proportional Band x 2
Negative Dead Band
Time
PID Control
Time
Dead Band
In a PID application the dead bands above and below
the set point can save an application’s energy and
wear by maintaining process temperature within acceptable ranges.
Proportional action ceases when the process value
is within the dead band. Integral action continues to
bring the process temperature to the set point.
Using a positive dead band value keeps the two
systems from fighting each other.
Cool Output Active
Set Point
Temperature
Heat Output Active
Positive Dead Band
Time
When the dead band value is zero, the heating output activates when the temperature drops below the set point, and the cooling output switches on
when the temperature exceeds the set point.
Watlow EZ-ZONE ® PM PID Controller
•
Adjust the dead band with Dead Band [``db]
(Operations Page, Loop Menu).
Variable Time Base
Variable time base is the preferred method for controlling a resistive load, providing a very short time
base for longer heater life. Unlike phase-angle firing,
variable-time-base switching does not limit the current and voltage applied to the heater.
With variable time base outputs, the PID algorithm calculates an output between 0 and 100%, but
the output is distributed in groupings of three ac
line cycles. For each group of three ac line cycles, the
controller decides whether the power should be on or
off. There is no fixed cycle time since the decision is
made for each group of cycles. When used in conjunction with a zero cross (burst fire) device, such as a
solid-state power controller, switching is done only at
the zero cross of the ac line, which helps reduce electrical noise (RFI).
Variable time base should be used with solid-state
power controllers, such as a solid-state relay (SSR)
or silicon controlled rectifier (SCR) power controller.
Do not use a variable time base output for controlling electromechanical relays, mercury displacement
relays, inductive loads or heaters with unusual resistance characteristics.
The combination of variable time base output and
a solid-state relay can inexpensively approach the ef81
•
Chapter 9 Features
fect of analog, phase-angle fired control.
Select the AC Line Frequency [AC;LF] (Setup Page,
Global Menu), 50 or 60 Hz.
Temperature
Set Point
100 percent output
Temperature reaches Set Point quickly
10 ON, 0 OFF
Time
Heating System without Ramping
Set Point
Temperature
50 percent output
3 ON, 3 OFF
degrees
per minute
Temperature ramps to Set Point at a set rate
Time
Heating System with Ramping
Alarms
66 percent output
6 ON, 3 OFF
Note:
When output 1 is a universal process output, output 2 cannot use variable time base, fixed time base
only.
Single Set Point Ramping
Ramping protects materials and systems that cannot tolerate rapid temperature changes. The value of
the ramp rate is the maximum degrees per minute or
hour that the system temperature can change.
Select Ramp Action [``rP] (Setup Page, Loop
Menu):
[`oFF] ramping not active.
[`Str] ramp at startup.
[StPt] ramp at a set point change.
[both] ramp at startup or when the set point
changes.
Select whether the rate is in degrees per minute
or degrees per hour with Ramp Scale [`r;SC]. Set
the ramping rate with Ramp Rate [`r;rt] (Setup
Page, Loop Menu).
Wat low EZ-ZONE ® PM PID Controller
•
Alarms are activated when the output level, process
value or temperature leaves a defined range. A user
can configure how and when an alarm is triggered,
what action it takes and whether it turns off automatically when the alarm condition is over.
Configure alarm outputs in the Setup Page before
setting alarm set points.
Alarms do not have to be assigned to an output.
Alarms can be monitored and controlled through the
front panel or by using software.
Process and Deviation Alarms
A process alarm uses one or two absolute set points
to define an alarm condition.
A deviation alarm uses one or two set points that
are defined relative to the control set point. High
and low alarm set points are calculated by adding or
subtracting offset values from the control set point.
If the set point changes, the window defined by the
alarm set points automatically moves with it.
Select the alarm type with Type [`A;ty] (Setup
Page, Alarm Menu).
Alarm Set Points
The alarm high set point defines the process value
or temperature that will trigger a high side alarm.
It must be higher than the alarm low set point and
lower than the high limit of the sensor range.
The alarm low set point defines the temperature
that will trigger a low side alarm. It must be lower
than the alarm high set point and higher than the
low limit of the sensor range.
82
•
Chapter 9 Features
View or change alarm set points with Low Set
Point [`A;Lo] and High Set Point [`A;hi] (Operations
Page, Alarm Menu).
The alarm state begins when the temperature
reaches the Alarm High Set Point
Alarm High
Set Point
Alarm Hysteresis
High Side Alarm Range
Alarm High Set Point
Temperature
Alarm Hysteresis
Normal Operating Range
Alarm Hysteresis
Low Side Alarm Range
Alarm Low Set Point
Time
Alarm Set Points and Hysteresis
Alarm Latching
A latched alarm will remain active after the alarm
condition has passed. It can only be deactivated by
the user.
An active message, such as an alarm message,
will cause the display to toggle between the normal
settings and the active message in the upper display
and [Attn] in the lower display.
Push the Advance Key to display [ignr] in the
upper display and the message source in the lower
display.
Use the Up ¿ and Down ¯ keys to scroll through
possible responses, such as Clear [`CLr] or Silence
[`SiL]. Then push the Advance ‰ or Infinity ˆ key
to execute the action.
See the Keys and Displays chapter and the Home
Page chapter for more details.
An alarm that is not latched (self-clearing) will
deactivate automatically when the alarm condition
has passed.
Turn alarm latching on or off with Latching
[`A;LA] (Setup Page, Alarm Menu).
Temperature
Alarm Hysteresis
An alarm state is triggered when the process value
reaches the alarm high or alarm low set point. Alarm
hysteresis defines how far the process must return
into the normal operating range before the alarm can
be cleared.
Alarm hysteresis is a zone inside each alarm set
point. This zone is defined by adding the hysteresis
value to the alarm low set point or subtracting the
hysteresis value from the alarm high set point.
View or change alarm hysteresis with Hysteresis
[`A;hy] (Setup Page, Alarm Menu).
Normal Operating Range
Process
Temperature
The alarm state continues until the
temperature drops to the Alarm High
Set Point minus the hysteresis. A
latching alarm could be turned off by
the operator at this point. A nonlatching alarm would turn off
automatically.
Alarm Low
Set Point
Time
Alarm Response with Hysteresis
Alarm Silencing
If alarm silencing is on the operator can disable the
alarm output while the controller is in an alarm
state. The process value or temperature has to enter
the normal operating range beyond the hysteresis
zone to activate the alarm output function again.
An active message, such as an alarm message,
will cause the display to toggle between the normal
settings and the active message in the upper display
and [Attn] in the lower display.
Push the Advance Key to display [ignr] in the
upper display and the message source in the lower
display.
Use the Up ¿ and Down ¯ keys to scroll through
possible responses, such as Clear [`CLr] or Silence
[`SiL]. Then push the Advance ‰ or Infinity ˆ key
to execute the action.
See the Keys and Displays chapter and the Home
Page chapter for more details.
Turn alarm silencing on or off with Silencing
[`A;Si] (Setup Page, Alarm Menu).
Alarm Blocking
Alarm blocking allows a system to warm up after
it has been started up. With alarm blocking on, an
alarm is not triggered when the process temperature is initially lower than the alarm low set point
or higher than the alarm high set point. The process
temperature has to enter the normal operating range
beyond the hysteresis zone to activate the alarm
function.
If the EZ-ZONE PM has an output that is functioning as a deviation alarm, the alarm is blocked
when the set point is changed, until the process value
re-enters the normal operating range.
Turn alarm blocking on or off with Blocking
[`A;bL] (Setup Page, Alarm Menu).
Open Loop Detection
When Open Loop Detection is enabled [`l; d e] , the
controller will look for the power output to be at
Watlow EZ-ZONE ® PM PID Controller
•
83
•
Chapter 9 Features
100%. Once there, the control will then begin to monitor the Open Loop Detect Deviation [`l; d d ] as it
relates to the value entered for the Open Loop Detect
Time [`l; d t] . If the specified time period expires
and the deviation does not occur, an Open Loop Error
will be triggered. Once the Open Loop Error condition exists the control mode will go off.
Note:
All prompts identified in this section can be found
in the Loop Menu of the Setup Page.
Programming the EZ Key/s
You can program the EZ Key either in the Setup
Menu or with configuration software, such as EZZONE Configurator, using a personal computer.
The following examples show how to program the
EZ Key to start and stop a profile.
Using keys and display:
1. To go to the Setup Page from the Home Page,
press both the Up ¿ and Down ¯ keys for six seconds. [``Ai] will appear in the upper display and
[`Set] will appear in the lower display.
2. Press the Up Key ¿ until [`Fun] appears in the
upper display and [`SEt] will appear in the lower
display.
3. Press the Advance Key ‰ until Digital Input
Level [`leu] appears in the lower display. Use an
arrow key to specify the state of the key (high or
low) when the controller is powered up. Functions
will toggle with each press of the EZ Key, such as
Profile Start/Stop.
4. Press the Advance Key ‰. The lower display will
show Digital Function [``Fn]. Press the Up ¿ or
Down ¯ key to scroll through the functions that
can be assigned to the EZ Key
When Profile Start/Stop [P;StS] appears in the
upper display and [``Fn] appears in the lower
display, press the Advance Key ‰ once to select
that function and move to the Function Instance
[``FS] parameter.
5. Press the Up ¿ or Down ¯ key to scroll to the
profile that you want the EZ Key to control.
6. The instance tells the controller which of the
numbered functions should be acted upon. For
profiles, there are 4 instances. Press the Infinity
Key ˆ once to return to the submenu, twice to
return to the main menu or three times to return
to the Home Page.
Using Lockout to Hide Pages and Menus
If unintentional changes to parameter settings might
raise safety concerns or lead to downtime, your can
use the lockout feature to make them more secure.
Each of the menus in the Factory Page and each
of the pages, except the Factory Page, has a security
Wat low EZ-ZONE ® PM PID Controller
•
level assigned to it. You can change the read and
write access to these menus and pages by using the
parameters in the Lockout Menu (Factory Page).
Lockout Menu
There are five parameters in the Lockout Menu (Factory Page):
• Lock Operations Page [LoC;o] sets the security lev-
el for the Operations Page. (default: 2)
Note:
The Home and Setup Page lockout levels are fixed and cannot be changed.
•Lock Profiling Page [LoC;P] sets the security level for the Profiling Page. (default: 3)
•Password Security Enable [ pas ; e ] will turn on or off the Password security feature. (default: off)
• Read Lockout Security [rLoC] determines which pages can be accessed. The user can access the se-
lected level and all lower levels. (default: 5)
•Set Lockout Security [SLoC] determines which pa-
rameters within accessible pages can be written to. The user can write to the selected level and all lower levels. (default: 5)
The table below represents the various levels of lockout for the Set Lockout Security prompt and the
Read Lockout Security prompt. The Set Lockout has
6 levels (0-5) of security where the Read Lockout has
5 (1-5). Therefore, level "0" applies to Set Lockout
only. "Y" equates to yes (can write/read) where "N"
equates to no (cannot write/read). The colored cells
simply differentiate one level from the next.
Lockout Security [SLoC] & [rloC]
Lockout Level
0
1
2
3
4
5
Home Page
Y
Y
Y
Y
Y
Y
Operations Page
N
N
Y
Y
Y
Y
Setup Page
N
N
N
N
Y
Y
Profile Page
N
N
N
Y
Y
Y
Factory Page
Custom Menu
N
N
N
N
N
Y
Diagnostic Menu
N
Y
Y
Y
Y
Y
Calibration Menu
N
N
N
N
N
Y
Lockout Menu
[LoC;O]
N
Y
Y
Y
Y
Y
[loC; p ]
N
Y
Y
Y
Y
Y
[ pas ; e ]
N
Y
Y
Y
Y
Y
[rloC]
Y
Y
Y
Y
Y
Y
[sloC]
Y
Y
Y
Y
Y
Y
The following examples show how the Lockout Menu
parameters may be used in applications:
1. You can lock out access to the Operations Page
but allow an operator access to the Profile Menu,
by changing the default Profile Page and Operations Page security levels. Change Lock Operations Page [LoC;o] to 3 and Lock Profiling Page
84
•
Chapter 9 Features
2
3.
4.
5.
[LoC;P] to 2. If Set Lockout Security [SLoC] is
set to 2 or higher and the Read Lockout Security
[rLoC] is set to 2, the Profiling Page and Home
Pages can be accessed, and all writable parameters can be written to. Pages with security levels
greater than 2 will be locked out (unaccessible).
If Set Lockout Security [SLoC] is set to 0 and
Read Lockout Security [rLoC] is set to 5, all
pages will be accessible, however, changes will
not be allowed on any pages or menus, with one
exception: Set Lockout Security [SLoC] can be
changed to a higher level.
The operator wants to read all the menus and not
allow any parameters to be changed.
In the Factory Page, Lockout Menu, set Read
Lockout Security [rLoC] to 5 and Set Lockout
Security [SLoC] to 0.
The operator wants to read and write to the
Home Page and Profiling Page, and lock all other
pages and menus.
In the Factory Page, Lockout Menu, set Read
Lockout Security [rLoC] to 2 and Set Lockout
Security [SLoC] to 2.
In the Factory Page, Lockout Menu, set Lock
Operations Page [LoC;O] to 3 and Lock Profiling
Page [LoC;P] to 2.
The operator wants to read the Operations
Page, Setup Page, Profiling Page, Diagnostics
Menu, Lock Menu, Calibration Menu and Custom Menus. The operator also wants to read and
write to the Home Page.
In the Factory Page, Lockout Menu, set Read
Lockout Security [rLoC] to 1 and Set Lockout
Security [SLoC] to 5.
In the Factory Page, Lockout Menu, set Lock
Operations Page [LoC;O] to 2 and Lock Profiling
Page [LoC;P] to 3.
1. [loC; l] , Locked Access Level (1 to 5) correspond
ing to the lockout table above.
2. [roll] , Rolling Password will change the Cus-
tomer Code every time power is cycled.
3. [ pas ; u ] , User Password which is needed for a Us-
er to acquire access to the control.
4. [ pas ; a ] , Administrator Password which is need-
ed to acquire administrative access to the control.
The Administrator can either change the User
and or the Administrator password or leave them in
the default state. Once Password Security is enabled
they will no longer be visible to anyone other than
the Administrator. As can be seen in the formula
that follows either the User or Administrator will
need to know what those passwords are to acquire a
higher level of access to the control. Back out of this
menu by pushing the Infinity ˆ key. Once out of the
menu, the Password Security will be enabled.
How to Acquire Access to the Control
To acquire access to any inaccessible Pages or Menus,
go to the Factory Page and enter the [UloC] menu.
Once there follow the steps below:
Note:
If Password Security (Password Enabled [ pas ; e ] is On) is enabled the two prompts mentioned below in the first step will not be visible. If unknown, call the individual or company that originally set-
up the control.
1. Acquire either the User Password [ pas ; u ] or the Administrator Password [ pas ; a ] .
Using Password Security
It is sometimes desirable to apply a higher level of
security to the control where a limited number of
menus are visible and not providing access to others
without a security password. Without the appropriate password those menus will remain inaccessible.
If Password Enabled [ pas ; e ] in the Factory Page
under the [`loC] Menu is set to on, an overriding
Password Security will be in effect. When in effect,
the only Pages that a User without a password has
visibility to are defined in the Locked Access Level
[loC;L] prompt. On the other hand, a User with a
password would have visibility restricted by the Read
Lockout Security [rloC] . As an example, with Password Enabled and the Locked Access Level [loC;L]
set to 1 and [rloC] is set to 3, the available Pages
for a User without a password would be limited to
the Home and Factory Pages (locked level 1). If the
User password is entered all pages would be accessible with the exception of the Setup Page as defined
by level 3 access.
Watlow EZ-ZONE ® PM PID Controller
How to Enable Password Security
Go to the Factory Page by holding down the Infinity
ˆ key and the Advance ‰ key for approximately six
seconds. Once there, push the Down ¯ key one time
to get to the [`loC] menu. Again push the Advance
‰ key until the Password Enabled [ pas ; e ] prompt
is visible. Lastly, push either the up or down key to
turn it on. Once on, 4 new prompts will appear:
•
2.Push the Advance ‰ key one time where the Code [Cod e] prompt will be visible.
Note:
a.If the the Rolling Password is off push the Ad-
vance key one more time where the Password [ pass] prompt will be displayed. Proceed to
either step 7a or 8a. Pushing the Up ¿ or Down ¯ arrow keys enter either the User or Adminis-
trator Password. Once entered, push and hold the Infinity ˆ key for two seconds to return to the Home Page.
b.If the Rolling Password [roll] was turned on proceed on through steps 3 - 9.
3. Assuming the Public Key [Cod e] prompt is still visible on the face of the control simply push the Advance key to proceed to the Password [ pass] prompt. If not find your way back to the Factory Page as described above.
85
•
Chapter 9 Features
4.Execute the calculation defined below (7b or 8b) for to) the Modbus address of a parameter within the either the User or Administrator.
ST control.
5.Enter the result of the calculation in the upper dis- Assembly Working Addresses
play by using the Up ¿ or Down ¯ arrow keys or - Fixed addresses directly related to their associ-
ated "Assembly Definition Addresses" (i.e., As-
use EZ-ZONE Confgurator Software.
sembly Working Addresses 200 & 201 will as-
6. Exit the Factory Page by pushing and holding the sume the parameter pointed to by Assembly Defi-
Infinity ˆ key for two seconds.
nition Addresses 40 & 41).
Formulas used by the User and the Administrator to
When the Modbus address of a target parameter is
calculate the Password follows:
stored in an "Assembly Definition Address" its corresponding working address will return that paramPasswords equal:
eter’s actual value. If it’s a writable parameter, writ7. User
ing to its working register will change the param a. If Rolling Password [roll] is Off, Password eter’s actual value.
[ pass] equals User Password [ pas ; u ] .
As an example, Modbus register 360 contains the
Analog Input 1 Process Value (See Operations Page,
b.If Rolling Password [roll] is On, Password Analog Input Menu). If the value 360 is loaded into
[ pass] equals:
Assembly Definition Address 91, the process value
([ pas ; u ] x code) Mod 929 + 70
sensed by analog input 1 will also be stored in Mod8. Administrator
bus registers 250 and 251. Note that by default this
a. If Rolling Password [roll] is Off, Password parameter is also stored in working registers 240
[ pass] equals User Password [ pas ; a ] .
and 241 as well.
b. If Rolling Password [roll] is On, Password The table (See Appendix: Modbus Programmable
[ pass] equals:
Memory Blocks) identified as "Assembly Definition
([ pas ; a ] x code) Mod 997 + 1000
Addresses and Assembly Working Addresses" reflects
Differences Between a User Without Password,
User With Password and Administrator
the assemblies and their associated addresses.
- User without a password is restricted by the Locked Access Level [loC; l] .
- A User with a password is restricted by the Read Lockout Security [rloC] never having ac-
cess to the Lock Menu [`loC] .
- An Administrator is restricted according to the Read Lockout Security [rloC] however, the Ad-
ministrator has access to the Lock Menu where the Read Lockout can be changed.
Modbus - Using Programmable Memory
Blocks
When using the Modbus protocol, the PM control features a block of addresses that can be configured by
the user to provide direct access to a list of 40 user
configured parameters. This allows the user easy access to this customized list by reading from or writing to a contiguous block of registers.
To acquire a better understanding of the tables
found in the back of this manual (See Appendix:
(Modbus Programmable Memory Blocks) please read
through the text below which defines the column
headers used.
Assembly Definition Addresses
-Fixed addresses used to define the parameter that will be stored in the "Working Addresses", which may also be referred to as a pointer. The value stored in these addresses will reflect (point Wat low EZ-ZONE ® PM PID Controller
•
86
•
Chapter 9 Features
Software Configuration
Using EZ-ZONE® Configurator Software
To enable a user to configure the PM control using
a personal computer (PC), Watlow has provided free
software for your use. If you have not yet obtained a
copy of this software insert the CD (Controller Support Tools) into your CD drive and install the software. Alternatively, if you are viewing this document
electronically and have a connection to the internet
simply click on the link below and download the software from the Watlow web site free of charge.
http://www.watlow.com/products/software/zone_config.cfm
Once the software is installed double click on the EZZONE Configurator icon placed on your desktop during the installation process. If you cannot find the
icon follow the steps below to run the software:
1. Move your mouse to the "Start" button
2. Place the mouse over "All Programs"
3. Navigate to the "Watlow" folder and then the sub-
folder "EZ-ZONE Configurator"
4.Click on EZ-ZONE Configurator to run.
The first screen that will appear is shown below.
If the PC is already physically connected to the EZZONE PM control click the next button to go on-line.
Note:
When establishing communications from PC to the
EZ-ZONE PM control an interface converter will be
required. The Standard Bus network uses EIA-485
as the interface. Most PCs today would require a
USB to EIA-485 converter. However, some PCs may
still be equipped with EIA-232 ports, therefore an
EIA-232 to EIA-485 converter would be required.
The available options allow the user to select "Try
them all" or to use a specific known communications
port. After installation of your converter if you are
not sure which communications port was allocated
select "Try them all" and then click next. The screen
to follow shows that the software is scanning for
devices on the network and that progress is being
made.
When complete the software will display all of the
available devices found on the network as shown below.
As can be seen in the above screen shot the software
provides the user with the option of downloading a
previously saved configuration as well as the ability
to create a configuration off-line to download later.
The screen shots that follow will take the user online.
After clicking the next button above it is necessary
to define the communications port on the PC to use.
Watlow EZ-ZONE ® PM PID Controller
•
87
•
Chapter 9 Features
In the previous screen shot the PM is shown highlighted to bring greater clarity to the control in focus. Any EZ-ZONE device on the network will appear in this window and would be available for the
purpose of configurationor monitoring. After clicking
on the control of choice simply click the next button
once again. The next screen appears below.
more clarity for the area of focus by not displaying
unwanted menus ad parameters. Once the focus is
brought to an individual parameter (single click of
mouse) as is the case for Analog Input 1 in the left
column, all that can be setup related to that parameter will appear in the center column. The grayed out
fields in the center column simply mean that this
In the screen shot above notice that the device part
number is clearly displayed at the top of the page
(green highlight added for emphasis). When multiple
EZ-ZONE devices are on the network it is important
that the part number be noted prior to configuring so as to avoid making unwanted configuration
changes to another control.
does not apply for the type of sensor selected. As an
example, notice that when RTD is selected, TC Linearization does not apply and is therefore grayed out.
To speed up the process of configuration notice that
at the bottom of the center column there is an option to copy settings. If Analog Input 1 and 2 are the
same type of sensor click on "Copy Settings" where a
copy from to copy to dialog box will appear allowing
for quick duplication of all settings.
Looking closely at the left hand column (Parameter
Menus) notice that it displays all of the available
menus and associated parameters within the control.
The menu structure as laid out within this software
follows:
-
Setup
Operations
Factory
Profile
Notice too, that by clicking on any of those items in
the center column that context sensitive help will appear for that particular item in the right hand column.
Navigating from one menu to the next is easy and
clearly visible. Simply slide the scroll bar up or down
to display the menu and parameter of choice. As an
alternative, clicking on the negative symbol next to
Setup will collapse the Setup Menu where the Operations Menu will appear next and perhaps deliver
Wat low EZ-ZONE ® PM PID Controller
• 88
•
Chapter 9 Features
Lastly, when the configuration is complete click the
"Finish" button at the bottom right of the previous
screen shot. The screen that follows this action can
be seen below.
The user can save the file to any folder of choice.
Although the PM control now contains the configuration (because the previous discussion focused on
doing the configuration on-line) it is suggested that
after the configuration process is completed that the
user save this file on the PC for future use. If for
some reason someone inadvertently changed a setting without understanding the impact it would be
easy and perhaps faster to download a saved configuration back to the control versus trying to figure out
what was changed.
Of course, there is an option to exit without saving a
copy to the local hard drive.
After selecting Save above click the "Finish" button
once again. The screen below will than appear.
When saving the configuration note the location
where the file will be placed (Saved in) and enter the
file name (File name) as well. The default path for
saved files follows:
\Program Files\Watlow\EZ-ZONE CONFIGURATOR\Saved Configurations
Watlow EZ-ZONE ® PM PID Controller
•
89
•
Chapter 9 Features
Chapter 10: Appendix
Troubleshooting Alarms, Errors and Control Issues
Indication
Description
Possible Causes
Alarm won’t clear or reset
Alarm will not clear or reset
with keypad or digital input
• Alarm latching is active
Alarm won’t occur
Alarm will not activate output
• Alarm silencing is active
• Alarm blocking is active
• Alarm is set to incorrect output
Corrective Action
• Reset alarm when process is
within range or disable latching
• Alarm set to incorrect output • Set output to correct alarm
source instance
• Alarm is set to incorrect
• Set alarm source to correct insource
put instance
• Correct cause of sensor input
• Sensor input is out of alarm
out of alarm range
set point range
• Set alarm set point to correct
• Alarm set point is incorrect
trip point
• Set alarm to correct type: pro• Alarm is set to incorrect type
cess, deviation or power
• Set digital input function and
• Digital input function is incorsource instance
rect
• Alarm is set to incorrect
source
• Alarm set point is incorrect
• Alarm is set to incorrect type
• Disable alarm silencing, if required
• Disable alarm blocking, if required
• Set output to correct alarm
source instance
• Set alarm source to correct input instance
• Set alarm set point to correct
trip point
• Set alarm to correct type: process, deviation or power
[AL;E1] Alarm Error
[AL;E2]
[AL;E3]
[AL;E4]
Alarm state cannot be determined due to lack of sensor
input
• Sensor improperly wired or
• Correct wiring or replace sensor
open
• Match setting to sensor used
• Incorrect setting of sensor type • Check calibration of controller
• Calibration corrupt
[AL;L1] Alarm Low
[AL;L2]
[AL;L3]
[AL;L4]
Sensor input below low alarm
set point
• Temperature is less than
• Check cause of under temperaalarm set point
ture
• Alarm is set to latching and an
alarm occurred in the past
• Clear latched alarm
• Incorrect alarm set point
• Establish correct alarm set
• Incorrect alarm source
point
• Set alarm source to proper setting
[AL;h1} Alarm High
[AL;h2]
[AL;h3]
[AL;h4]
Sensor input above high alarm
set point
• Temperature is greater than
• Check cause of over temperaalarm set point
ture
• Alarm is set to latching and an
alarm occurred in the past
• Clear latched alarm
• Incorrect alarm set point
• Establish correct alarm set
• Incorrect alarm source
point
• Set alarm source to proper setting
[Er;i1] Error Input
Sensor does not provide a valid
signal to controller
• Sensor improperly wired or
• Correct wiring or replace sensor
open
• Match setting to sensor used
• Incorrect setting of sensor type • Check calibration of controller
• Calibration corrupt
Indication
Description
Wat low EZ-ZONE ® PM PID Controller
Possible Causes
•
90
•
Corrective Action
Appendix
[LP;o1]
Loop Open Error
Open Loop Detect is active and
the process value did not deviate by a user-selected value in
a user specified period.
• Setting of Open Loop Detect
Time incorrect
• Setting of Open Loop Detect
Deviation incorrect
• Thermal loop is open
• Set correct Open Loop Detect
Time for application
• Set correct Open Loop Deviation value for application
• Determine cause of open thermal loop: misplaced sensors,
load failure, loss of power to
• Open Loop Detect function not load, etc.
required but activated
• Deactivate Open Loop Detect
feature
[LP;r1]
Loop Reversed Error
Open Loop Detect is active and
the process value is headed
in the wrong direction when
the output is activated based
on deviation value and userselected value.
• Setting of Open Loop Detect
Time incorrect
• Setting of Open Loop Detect
Deviation incorrect
• Output programmed for incorrect function
• Thermocouple sensor wired in
reverse polarity
• Set correct Open Loop Detect
Time for application
• Set correct Open Loop Deviation value for application
• Set output function correctly
• Wire thermocouple correctly,
(red wire is negative)
[`rP1] Ramping 1
Controller is ramping to new set • Ramping feature is activated
point
• Disable ramping feature if not
required
[tUN1] Autotuning 1
Controller is autotuning the con- • User started the autotune
trol loop
function
• Wait until autotune completes
or disable autotune feature
• Set digital input to function
other than autotune, if desired
• Digital input is set to start
autotune
No heat/cool action
Output does not activate load
• Output function is incorrectly • Set output function correctly
set
• Set control mode appropriately
• Control mode is incorrectly set (Open vs Closed Loop)
• Correct output wiring
• Output is incorrectly wired
• Correct fault in system
• Load, power or fuse is open
• Set control set point in appro• Control set point is incorrect
priate control mode and check
source of set point: remote, idle,
profile, closed loop, open loop
• Obtain correct controller model
• Incorrect controller model for
for application
application
No Display
No display indication or LED illumination
•
•
•
•
•
No Serial Communication
Cannot establish serial communications with the controller
Power to controller is off
Fuse open
Breaker tripped
Safety interlock switch open
Separate system limit control
activated
• Wiring error
• Incorrect voltage to controller
• Turn on power
• Replace fuse
• Reset breaker
• Close interlock switch
• Reset limit
• Address parameter incorrect
• Incorrect protocol selected
• Baud rate incorrect
• Parity incorrect
• Wiring error
• EIA-485 converter issue
• Incorrect computer or PLC
communications port
• Incorrect software setup
• Set unique addresses on network
• Match protocol between devices
• Match baud rate between devices
• Match parity between devices
• Correct wiring issue
• Check settings or replace converter
• Set correct communication port
• Termination resistor may be
required
Watlow EZ-ZONE ® PM PID Controller
•
91
•
• Correct wiring issue
• Apply correct voltage, check
part number
• Correct software setup to match
controller
• Place 120 Ω resistor across
EIA-485 on last controller
Appendix
Indication
Description
Possible Causes
Corrective Action
Process doesn’t control to set
point
Process is unstable or never
reaches set point
• Controller not tuned correctly
Temperature runway
Process value continues to increase or decrease past set
point.
• Controller output incorrectly
programmed
• Thermocouple reverse wired
[`100] Device Error
[rEtn]
Controller displays internal mal- • Controller defective
function message at power up.
• Replace or repair controller
Menus inaccessible
Unable to access [`SEt], [OP- • Security set to incorrect level
Er], [FCty] or [ProF] menus • Digital input set to lockout
or particular prompts in Home
keypad
Page
• Custom parameters incorrect
• Check lockout setting in Factory Page
• Change state of digital input
• Change custom parameters in
Factory Page
EZ-Key doesn’t work
EZ-Key does not activate required function
• Verify EZ-Key function in Setup
Menu
• Check that the function instance is correct
• Replace or repair controller
Wat low EZ-ZONE ® PM PID Controller
• Perform autotune or manually
tune system
• Control mode is incorrectly set • Set control mode appropriately
(Open vs Closed Loop)
• Control set point is incorrect
• Set control set point in appropriate control mode and check
source of set point: remote, idle,
profile, closed loop, open loop
• Verify output function is correct
(heat or cool)
• Correct sensor wiring (red wire
negative)
• Controller output wired incor- • Verify and correct wiring
rectly
• Replace heater
• Short in heater
• Replace or repair power con• Power controller connection to
troller
controller defective
• Controller output defective
• Replace or repair controller
• EZ-Key function incorrect
• EZ-Key function instance not
incorrect
• Keypad malfunction
•
92
•
Appendix
Modbus - Programmable Memory Blocks
Assembly Definition Addresses and Assembly Working Addresses
Assembly Definition
Addresses
40 & 41
42 & 43
44 & 45
46 & 47
48 & 49
50 & 51
52 & 53
54 & 55
56 & 57
58 & 59
60 & 61
62 & 63
64 & 65
66 & 67
68 & 69
70 & 71
72 & 73
74 & 75
76 & 77
78 & 79
Assembly Working
Addresses
200 & 201
202 & 203
204 & 205
206 & 207
208 & 209
210 & 211
212 & 213
214 & 215
216 & 217
218 & 219
220 & 221
222 & 223
224 & 225
226 & 227
228 & 229
230 & 231
232 & 233
234 & 235
236 & 237
238 & 239
Assembly Definition
Addresses
80 & 81
82 & 83
84 & 85
86 & 87
88 & 89
90 & 91
92 & 93
94 & 95
96 & 97
98 & 99
100 & 101
102 & 103
104 & 105
106 & 107
108 & 109
110 & 111
112 & 113
114 & 115
116 & 117
118 & 119
Assembly Working
Addresses
240 & 241
242 & 243
244 & 245
246 & 247
248 & 249
250 & 251
252 & 253
254 & 255
256 & 257
256 & 259
260 & 261
262 & 263
264 & 265
266 & 267
268 & 269
270 & 271
272 & 273
274 & 275
276 & 277
278 & 279
Assembly Definition
Addresses
Default Pointers
Assembly Working
Addresses
Assembly Definition
Addresses
Default Pointers
Assembly Working
Addresses
Registers 40 & 41
Registers 200 & 201
Registers 60 & 61
Registers 220 & 221
Pointer 1 = 1880 & 1881
Loop Control Mode
Registers 42 & 43
Pointer 2 = 2160 & 2161
Closed Loop Set Point
Registers 44 & 45
Pointer 3 = 2162 & 2163
Open Loop Set Point
Registers 46 & 47
Pointer 4 = 1480 & 1481
Alarm 1 High Set Point
Registers 48 & 49
Pointer 5 = 1482 & 1483
Alarm 1 Low Set Point
Registers 50 & 51
Pointer 6 = 1530 & 1531
Alarm 2 High Set Point
Registers 52 & 53
Pointer 7 = 1532 & 1533
Alarm 2 Low Set Point
Registers 54 & 55
Pointer 8 = 1580 & 1581
Alarm 3 High Set Point
Registers 56 & 57
Pointer 9 = 1582 & 1583
Alarm 3 Low Set Point
Registers 58 & 59
Pointer 10 = 1630 & 1631
Alarm 4 High Set Point
Pointer 11 = 1632 & 1633
Alarm 4 Low Set Point
Value of Pointer 1
Registers 62 & 63
Registers 202 & 203
Pointer 12 = 2540 & 2541
Profile Action Request
Value of Pointer 2
Registers 64 & 65
Registers 204 & 205
Pointer 13 = 2520 & 2521
Profile Start
Value of Pointer 3
Registers 66 & 67
Registers 206 & 207
Pointer 14 = 1890 & 1891
Heat Proportional Band
Value of Pointer 4
Registers 68 & 69
Registers 208 & 209
Pointer 15 = 1892 & 1893
Cool Proportional Band
Value of Pointer 5
Registers 70 & 71
Registers 210 & 211
Pointer 16 = 1894 & 1895
Time Integral
Value of Pointer 6
Registers 72 & 73
Registers 212 & 213
Pointer 17 = 1896 & 1897
Time Derivative
Value of Pointer 7
Registers 74 & 75
Registers 214 & 215
Pointer 18 = 1900 & 1901
Heat Hysteresis
Value of Pointer 8
Registers 76 & 77
Registers 216 & 217
Pointer 19 = 1902 & 1903
Cool Hysteresis
Value of Pointer 9
Registers 78 & 79
Registers 218 & 219
Pointer 20 = 1898 & 1899
Deadband
Value of Pointer 10
Watlow EZ-ZONE ® PM PID Controller
•
93
•
Value of Pointer 11
Registers 222 & 223
Value of Pointer 12
Registers 224 & 225
Value of Pointer 13
Registers 226 & 227
Value of Pointer 14
Registers 228 & 229
Value of Pointer 15
Registers 230 & 231
Value of Pointer 16
Registers 232 & 233
Value of Pointer 17
Registers 234 & 235
Value of Pointer 18
Registers 236 & 237
Value of Pointer 19
Registers 238 & 239
Value of Pointer 20
Appendix
Modbus Default Assembly Structure 80-119
Assembly Definition
Addresses
Default Pointers
Assembly Working
Addresses
Assembly Definition
Registers
Default Pointers
Assembly Working
Registers
Registers 80 & 81
Registers 240 & 241
Registers 100 & 101
Registers 260 & 261
Pointer 21 = 360 & 361
Analog Input 1 Process
Value
Registers 82 & 83
Pointer 22 = 362 & 363
Analog Input 1 Error Status
Registers 84 & 85
Pointer 23 = 440 & 441
Analog Input 2 Process
Value
Registers 86 & 87
Pointer 24 = 442 & 443
Analog Input 2 Error Status
Pointer 31 = 1882 & 1883
Control Mode Active
Value of Pointer 21
Registers 102 & 103
Registers 242 & 243
Pointer 32 = 1904 & 1905
Heat Power
Value of Pointer 22
Registers 104 & 105
Registers 244 & 245
Pointer 33 = 1906 & 1907
Cool Power
Value of Pointer 23
Registers 106 & 107
Registers 246 & 247
Pointer 34 = 690 & 691
Limit State
Value of Pointer 24
Registers 108 & 109
Registers 88 & 89
Pointer 25 = 1496 & 1497
Alarm 1 State
Registers 248 & 249
Pointer 35 = 2520 & 2521
Profile Start
Value of Pointer 25
Registers 110 & 111
Registers 90 & 91
Pointer 26 = 1546 & 1547
Alarm 2 State
Registers 92 & 93
Pointer 27 = 1596 & 1597
Alarm 3 State
Pointer 36 = 2540 & 2541
Profile Action Request
Registers 250 & 251
Pointer 28 = 1646 & 1647
Alarm 4 State
Registers 112 & 113
Pointer 37 = 2524 & 2525
Active File
Registers 252 & 253
Pointer 29 = 1328 & 1329
Digital Input 5 Status
Registers 98 & 99
Pointer 30 = 1348 & 1349
Digital Input 6 Status
Value of Pointer 32
Registers 264 & 265
Value of Pointer 33
Registers 266 & 267
Value of Pointer 34
Registers 268 & 269
Value of Pointer 35
Registers 270 & 271
Value of Pointer 36
Registers 272 & 273
Value of Pointer 37
Value of Pointer 27
Pointer 38 = 2526 & 2527
Active Step
Registers 254 & 256
Registers 274 & 275
Value of Pointer 38
Value of Pointer 28
Registers 116 & 117
Registers 96 & 97
Registers 262 & 263
Value of Pointer 26
Registers 114 & 115
Registers 94 & 95
Value of Pointer 31
Pointer 39 = 2528 & 2529
Active Set Point
Registers 256 & 257
Registers 276 & 277
Value of Pointer 39
Value of Pointer 29
Registers 118 & 119
Pointer 40 = 2536 & 2537
Step Time Remaining
Registers 258 & 259
Registers 278 & 279
Value of Pointer 40
Value of Pointer 30
Wat low EZ-ZONE ® PM PID Controller
•
94
•
Appendix
Specifications
LineVoltage/Power (Minimum /Maximum Ratings)
•85 to 264V~ (ac), 47 to 63Hz
•20 to 28VÅ (ac), 47 to 63Hz
•12 to 40VÎ (dc)
•14VA maximum power consumption (PM4, 8 & 9)
•10VAmaximum power consumption (PM3 & 6)
•Data retention upon power failure via nonvolatile memory
•Compliant with SEMIF47-0200, FigureR1-1 voltage sag requirements @24V ~ (ac) or higher
Environment
•0 to 149°F (-18 to 65°C) operating temperature
•-40 to 185°F (-40 to 85°C) storage temperature
•0 to 90%RH, non-condensing
ance
Voltage Input Ranges
- Accuracy ±10mV ±1 LSD at standard conditions
- Temperature stability ±100 PPM/°C maximum
Milliamp Input Ranges
- Accuracy ±20µA ±1 LSD at standard conditions
- Temperature stability ±100 PPM/°C maximum
Resolution Input Ranges
- 0 to 10V: 200 µV nominal
- 0 to 20 mA: 0.5 mA nominal
•Potentiometer: 0 to 1,200Ω
•Inverse scaling
Accuracy
•Calibration accuracy and sensor conformity: ±0.1% of span, ±1°C
@ the calibrated ambient temperature and rated line voltage
•Types R, S, B; 0.2%
•Type T below -50°C; 0.2%
•Calibration ambient temperature @ 77 ±5°F (25±3°C)
•Accuracy span :1000 °F (540°C) min.
•Temperature stability: ±0.1 °F/°F (±0.1 °C/°C) rise in ambient
maximum
Input Type
Max
Error
@ 25
Deg C
Accuracy
Range
Low
Accuracy
Range
High
Units
J
±1.75
0
750
Deg C
K
±2.45
-200
1250
Deg C
T (-200 to 350)
±1.55
0
350
Deg C
N
±2.25
0
1250
Deg C
E
±2.10
-200
900
Deg C
R
±3.9
0
1450
Deg C
S
±3.9
0
1450
Deg C
B
±2.66
870
1700
Deg C
C
±3.32
0
2315
Deg C
Agency Approvals
•UL® Listed to UL® 61010-1 File E185611
•UL® Reviewed to CSA C22.2 No.61010-1-04
•UL® 50 Type 4X, NEMA 4X indoor locations, IP66 front panel
seal (indoor use only)
•FM Class 3545 File 3029084 temperature limit switches
•CE-See Declaration of Conformity RoHS and W.E.E.E.compliaint
•This equipment is suitable for use in Class 1, Div.2, Groups A, B, C and D or non-hazardous locations only. Temperature Code T4A
•UL® Listed to ANSI/ISA 12.12.01-2007 File E184390
•PM3/6 CSA C22. No. 24 File 158031 Class 4813-02, both 1/32 and 1/16 DIN CSA approved
•UL® reviewed to Standard No. CSA C22.2 No.213-M1987, Cana-
dain Hazardous locations
D
±3.32
0
2315
Deg C
F (PTII)
±2.34
0
1343
Deg C
RTD, 100 ohm
±2.00
-200
800
Deg C
RTD, 1000 ohm
±2.00
-200
800
DegC
mV
±0.05
0
50
mV
Volts
±0.01
0
10
Volts
mAdc
±0.02
0
20
mAmps
DC
mAac
±5
-50
50
mAmps
AC
Potentiometer,
1K range
±1
0
1000
Ohms
Thermistor, 5K
range
±5
0
5000
Ohms
Thermistor,
10K range
±10
0
10000
Ohms
Isolated Serial Communications
Thermistor,
Thermistor
±20
0
20000
Ohms
Wiring Termination—Touch-Safe Terminals
Thermistor,
40K range
±40
0
40000
Ohms
Controller
•User selectable heat/cool, on-off, P, PI, PD, PID or alarm action
•Auto-tune with TRU-TUNE®+ adaptive control algorithm
•Control sampling rates: input = 10Hz, outputs = 10Hz
Profile Ramp/Soak - Real Time Clock and Battery Back-up
•Accuracy (typical): ±30PPM at 77°F (25°C)
•+30/-100 PPM at -4 to 149°F (-20 to 65°C)
•Battery type: lithium (recycle properly)
•Battery typical life: three cumulative years of unpowered life at
77°F (25°C)
•EIA232/485, Modbus® RTU
•Input, power and controller output terminals are touch safe re
movable 3.30 to 0.0507 mm2 (12 to 22 AWG)
•Wire strip length 7.6 mm (0.30 in.)
•Torque 0.8 Nm (7.0 lb.-in.)
Operating Range
Input Type
Range Low
Range High
Universal Input
J
-210
1200
•Thermocouple, grounded or ungrounded sensors
•>20MΩ input impedance
•3µA open sensor detection
•Max. of 2KΩ source resistance
•RTD 2 or 3 wire, platinum, 100Ω and 1000Ω @ 0°C calibration to
DIN curve (0.00385Ω/Ω/°C)
•Process, 0-20mA @ 100Ω ,or 0-10V Î(dc) @ 20kΩ input imped-
K
-270
1371
Watlow EZ-ZONE ® PM PID Controller
•
95
•
T
-270
400
N
-270
1300
E
-270
1000
R
-50
1767
Appendix
Operating Range
S
-50
1767
B
-50
1816
C
0
2315
D
0
2315
F (PTII)
0
1343
RTD (100 ohm)
-200
800
RTD (1000 ohm)
-200
800
mV
-50
50
Volts
0
10
mAdc
0
20
mAac
-50
50
Potentiometer, 1K
range
0
1200
Resistance, 5K range
0
5000
Resistance, 10K range
0
10000
Resistance, 20K range
0
20000
Resistance, 40K range
0
40000
- 0 to 20mA into max. 800Ω load
Resolution
- dc ranges: 2.5mV nominal
- mA ranges: 5 µA nominal
Calibration Accuracy
- dc ranges: ±15 mV
- mA ranges: ±30 µA
Temperature Stability
- 100 ppm/°C
Operator Interface
•Dual 4 digit, 7 segment LED displays
•Advance, infinity, up and down keys, plus optional programmable EZ-KEY(s) depending on model size
•Typical display update rate 1Hz
•RESET key substituted for infinity on all models including the limit control
Dimensions
Dimensions
Size
Thermistor Input
1/32
• 0 to 40KΩ, 0 to 20KΩ, 0 to 10KΩ, 0 to 5KΩ
• 2.252KΩ and 10KΩ base at 77°F (25°C)
• Linearization curves built in
• Third party Thermistor compatibility requirements
Base R
@ 25C
Alpha
Techniques
Beta
THERM
YSI
2.252K
Curve A
2.2K3A
004
A
10K
Curve A
10K3A
016
B
10K
Curve C
10K4A
006
C
Prompt
Behind
Panel
(max.)
Width
Height
101.6 mm
(4.00 in)
53.3 mm
(2.10 in)
30.9 mm
(1.22 in)
left: 7.59 mm (0.299
in)
right: 5.90 mm (0.220
in)
1/4
100.8 mm
(3.97 in)
100.3 mm
(3.95 in)
100.3 mm
(3.95 in)
up: 11.43 mm (0.450
in)
middle: 9.53 mm
(0.375 in)
low: 7.62 mm (0.300
in)
1/16
101.6 mm
(4.00 in)
53.3 mm
(2.10 in)
53.3 mm
(2.10 in)
up: 10.80 mm (0.425
in)
low: 6.98 mm (0.275
in)
53.9 mm
(1.22 in)
top: 11.4 mm (0.450
in)
middle: 9.53 mm
(0.375 in)
bottom: 7.62 mm
(0.300 in)
100.3 mm
(3.95 in)
top: 11.4 mm (0.450
in)
middle: 9.53 mm
(0.375 in)
bottom: 7.62 mm
(0.300 in)
[``t;C]
2 Digital Input/Output Option - 2 DIO
•Digital input update rate 10Hz
- DC voltage
• Max. input 36V @ 3mA
• Min. high state 3V at 0.25mA
• Max. low state 2V
- Dry contact
• Min. open resistance 10KΩ
• Max. closed resistance 50Ω
• Max. short circuit 20mA
•Digital output update rate 10Hz
- Output voltage 24V, current limit, Output 6 =
10mA max., Output 5 = 3 pole DIN-A-MITE ® or 24mA max.
Output Hardware
•Switched dc = 22 to 32VÎ (dc) @30mA
•Switched dc/open collector = 30VÎ (dc) max. @ 100mA max. cur-
rent sink
•Solid state relay (SSR), FormA, 0.5A @ 24VÅ (ac) min., 264V Å (ac) max., opto-isolated, without contact suppression, 20 VA 120/240VÅ (ac) pilot duty
•Electromechanical relay, FormC, 5A, 24 to 240VÅ (ac) or 30VÎ (dc)max., resistive load, 100,000 cycles at rated load, 125 VA pilot duty at 120/240VÅ (ac), 25 VA at 24VÅ (ac)
•Electromechanical relay, FormA, 5A, 24 to 240VÅ (ac) or 30VÎ (dc) max., resistive load, 100,000 cycles at rated load, 125 VA pilot duty at 120/240VÅ (ac), 25 VA at 24VÅ (ac)
•NO-ARC relay, FormA, 15A, 24 to 240VÅ (ac), noVÎ (dc), resis-
tive load, 2 million cycles at rated load
•Universal process/retransmit, Output range selectable:
- 0 to 10V Î(dc) into a min. 1,000Ω load
Wat low EZ-ZONE ® PM PID Controller
•
Display Character
Height
1/8
(H)
1/8
(V)
101.6 mm
(4.00 in)
100.3 mm
(2.10 in)
101.6 mm
(4.00 in)
53.3 mm
(2.10 in)
Weight
1/32 DIN (PM3)
1/8 DIN (PM8&9)
• Controller: 127 g (4.5 oz.)
• Controller: 284 g (10 oz.)
1/16 DIN (PM6)
• Controller: 186 g (6.6 oz.)
1/4 DIN (PM4)
• Controller: 331 g (11.7 oz.)
User Manual
• User manual: 221.81 g
(7.82 oz)
Modbus® is a trademark of AEG Schneider Automation Inc.
EtherNet/IP™ is a trademark of ControlNet International Ltd. used
under license by Open DeviceNet Vendor Association, Inc. (ODVA).
UL® is a registered trademark of Underwriters Laboratories Inc.
DeviceNet™ is a trademark of Open DeviceNet Vendors Associatlon.
Note:
These specifications are subject to change without prior no-
tice.
96 • Appendix
Ordering Information for PID Controller Models
P M __ __ __ __ __ - __ A A A A __ __
Controller
EZ-ZONE® PID Controller Models
TRU-TUNE+® Adaptive Tune, red-green 7-segment displays
Package Size
3
6
8
9
4
Panel Mount 1/32 DIN
Panel Mount 1⁄16 DIN
Panel Mount 1⁄8 DIN Vertical
Panel Mount 1⁄8 DIN Horizontal
Panel Mount 1⁄4 DIN Horizontal
Primary Function
C
R
B
PID Controller with Universal Input
PID Controller with Universal Input and Profiling Ramp and Soak
PID Controller with Universal Input and Profiling Ramp and Soak
and Battery Backup with Real Time Clock
J
PID Controller with Thermistor Input
N
PID Controller with Thermistor Input and Profiling Ramp and Soak
E
PID Controller with Thermistor Input and Profiling Ramp and Soak
and Battery Backup with Real Time Clock
S
Custom Firmware
- Options B and E are not available with PM3 or PM6
Power Supply, Digital Input/Output
1
2
3
4
100 to 240VÅ (ac)
100 to 240VÅ (ac) plus 2 Digital I/O points
15 to 36VÎ (dc) and 24VÅ (ac)
15 to 36VÎ (dc) and 24VÅ (ac), plus 2 Digital I/O points
Output 1 and 2 Hardware Options
Output 1
Output 2
CA
Switched dc/open collector
None
CH
Switched dc/open collector
NO-ARC 15 A power control
CC
Switched dc/open collector
Switched dc
CJ
Switched dc/open collector
Mechanical relay 5 A, form A
CK
Switched dc/open collector
Solid-State Relay 0.5 A, form A
EA
Mechanical relay 5 A, form C
None
EH
Mechanical relay 5 A, form C
NO-ARC 15 A power control
EC
Mechanical relay 5 A, form C
Switched dc
EJ
Mechanical relay 5 A, form C
Mechanical relay 5 A, form A
EK
Mechanical relay 5 A, form C
Solid-State Relay 0.5 A, form A
FA
Universal process
None
FC
Universal process
Switched dc (cannot use variable time base)
FJ
Universal process
Mechanical relay 5 A, form A (cannot use variable time base)
FK
Universal process
Solid-State Relay 0.5 A, form A (cannot use variable time base)
AK
None
Solid-State Relay 0.5 A, form A
KH
Solid-State Relay 0.5 A, form A NO-ARC 15 A power control
KK
Solid-State Relay 0.5 A, form A Solid-state relay 0.5 A, form A
- Options CH, EH and KH are not available with PM3 (1/32 DIN)
Communications Options
A
None
1
EIA 485 Modbus RTU®
- Standard Bus EIA-485 always included - all models
Future Options
AAAA None
Custom Options
AA
12
Standard EZ-ZONE face plate
Class 1, Div. 2 (Not available with mechanical relay output types E, H, J)
Watlow EZ-ZONE ® PM PID Controller
•
97
•
Appendix
Index
[`A;bL] Alarm Blocking 58, 83
[AC;LF] AC Line Frequency 60, 82
[`A;dL] Alarm Delay 59
[A;dSP] Alarm Display 59
[`A;hi] Alarm High Set Point 39, 83
[`A;hy] Alarm Hysteresis 58, 83
[``Ai] Analog Input Menu 34, 45
[`A;LA] Alarm Latching 58, 83
[AL;E1] [AL;E2] [AL;E3] [AL;E4]
Alarm Error 1 to 4 27
[`A;Lg] Alarm Logic 58
[AL;h1] [AL;h2] [AL;h3] [AL;h4]
Alarm High 1 to 4 27
[AL;h1] [AL;h2] [AL;h3] [AL;h4]
Alarm High 1 to 4 27
[AL;L1] [AL;L2] [AL;L3] [AL;L4]
Alarm Low 1 to 4 27
[AL;L1] [AL;L2] [AL;L3] [AL;L4]
Alarm Low 1 to 4 27
[AL;L1] [AL;L2] [AL;L3] [AL;L4]
Alarm Low 1 to 4 27
[ALM] Alarm Menu 39, 57
[`A;Lo] Alarm Low Set Point 39, 83
[`A;Sd] Alarm Sides 58
[`A;Si] Alarm Silencing 59, 83
[`A;tP] Absolute Temperature 47
[A;tSP] Autotune Set Point 37, 74
[Attn] Attention 27, 28, 83
[`A;ty] Alarm Type 57, 82
[a;unt] Altitude Units 49
[`AUt] Autotune 37, 74
[bPLS] 79
[`C;Ag] Cool Algorithm 52, 80
[`CAL] Calibration Menu 71
[`C;Cr] Cool Output Curve 52, 79
[`C_F] Display Units 60
[Chan] Channel 62
[`C;hy] Cool Hysteresis 38, 80
[C;led] Communications LED Activity 61
[CloC] Wait for Time 65
[`CLr] Clear 83
[`C;M] Control Mode 37, 79
[C;MA] Control Mode Active 36
[Code] Public Key 68, 71
[CoM] Communications Menu 62,
63, 65, 69
[`C;Pb] Cool Proportional Band 38,
75, 80
[`C;Pr] Cool Power 36, 75
[`C;SP] Closed Loop Set Point 37
[`C;SP] Closed Loop Working Set
Point 36
[CUSt] Custom Menu 28, 74
[dAtE] Date of Manufacture 71
[``db] Dead Band 38, 81
[`dEC] Decimal 46
[`dio] Digital Input/Output Menu
36, 49
[`dir] Direction 49
[`do;S] Digital Output State 36
[dow] Day of Week 63
[d;prs] Display Pairs 44, 62
[`d;ti] Display Time 62
[`Ei;S] Event Input Status 36
[ELi;o] Electrical Input Offset 72,
76
[ELi;S] Electrical Input Slope 72,
76
[ELo;o] Electrical Output Offset 72
[Ent1] Active Event Output 1 41,
42
[Ent2] Event Output 2 67
[Er;i1] [Er;i2] Error Input 1 or 2
27
[Er;i1] Error Input 1 27
[FAiL] Input Error Failure 53, 79
[``Fi] Digital Output Function
Instance 50, 52
[``Fi] Output Function Instance
55, 56
[`FiL] Filter 46
[`FiL] Filter Time 77
[``Fn] Output Function 55, 56
[``Fn] Function 48
[`FUn] Function Key Menu 59
[gLbL] Global Menu 60
[`gSd] Guaranteed Soak Deviation
61
[GSd1] Guaranteed Soak Deviation
1 61
[`gSE] Guaranteed Soak Enable
61
[`GSE] Guaranteed Soak Enable
61
[`h;Ag] Heat Algorithm 52, 80
[`h;hy] Heat Hysteresis 37, 80
[hour] 33
[hoUr] 63
[hoUr] Hours 41
Hours Remaining 33
Minutes Remaining 33
Seconds Remaining 33
[hoUr] Hours 63
[`h;Pb] Heat Proportional Band 37,
75, 80
[`h;Pr] Heat Power 36, 75
[`i;CA] Calibration Offset 34, 76–77
[`id;S] Idle Set Point 37
[`i;Er] Input Error Latching 46
[`i;Er] Input Error Status 34
[`iP;1] Input Point 1 47
[`iP;2] Input Point 2
[`iP;3] Input Point 3
Wat low EZ-ZONE ® PM PID Controller
•
98
•
[`iP;4] Input Point 4 47
[`iP;2] Input Point 2 47
[`iP;3] Input Point 3 47
[`iP;4] Input Point 4 47
[`iP;5] Input Point 5 47
[`iP;6] Input Point 6 48
[`iP;7] Input Point 7 48
[`iP;8] Input Point 8 48
[`iP;9] Input Point 9 48
[iP;10] Input Point 10 48
[iP;F4] IP Fixed Address Part 4 61,
62
[``JC] Jump Count Remaining 42
[``JS] Jump Step 66
[`L;dd] Open Loop Detect Deviation 54
[`L;dE] Open Loop Detect Enable
53
[`L;dt] Open Loop Detect Time 53
[`Lin] Linearization 45
[`Lnr] Linearization Menu 34, 46
[`LoC] Security Setting Menu 69,
71
[loC;l], Locked Access Level 85
[loC;l] Locked Access Level 68, 70
[LoC;o] Lock Operations Page 69,
84
[LoC;P] Lock Profiling Page 70, 71,
84
[LooP] Control Loop Menu 52
[LooP] Loop Menu 37
[LP;o1] Loop Open Error 27
[LP;o1] Loop Open Error 1 27
[LP;r1] Loop Reversed Error 27
[LP;r1] Loop Reversed Error 1 27
[MAn] 79
[MAn] Manual Power 53
[map] Data Map 32
[min] 33
[min] Minutes 41
[Min] Minutes 63
[Mon] Monitor Menu 36
[`Mu] Electrical Measurement 71,
76
[`nU;S] Non-volatile Save 63
[`nU;S] Non-volatile Save 63
[`o;CA] Calibration Offset 57
[`o;Ct] Output Control 50, 55
[`o;Fn] Output Function 75, 78
[oFSt] PV Offset 35
[`o;hi] Output High Power Scale
50, 56
[`o;Lo] Output Low Power Scale
50, 55
[``oP] Open Loop Set Point 38
[`oP;2] Output Point 2 47
[`oP;3] Output Point 3 47
Appendix
[`oP;4] Output Point 4 47
[`oP;5] Output Point 5 47
[`oP;6] Output Point 6 48
[`oP;7] Output Point 7 48
[`oP;8] Output Point 8 48
[`oP;9] Output Point 9 48
[oP;10] Output Point 10 48
[`o;tb] Output Time Base 50, 55
[otPt] Output Menu 55
[`o;ty] Output Type 56, 78
[pas;a], Administrator Password 85
[pas;a] Administrator Password 68,
70
[pas;e] Password Enable 68, 70
[pass] Password 71
[Pass] Password 68
[pas;u], User Password 85
[pas;u] User Password 68, 70
[p;dl] Peltier Delay 53
[`P;EE] Process Error Enable 46
[`P;EL] Process Error Low 46
[``Pn] Part Number 71
[poti] Power Out Time 44
[`pro] Process 47
[P;StA] Profile Status Menu 40
[P;tyP] Profile Type 61
[p;unt] Pressure Units 49
[``Pu] Process Value Menu 48
[`Pu;A] Process Value Active 36
[`r;En] Remote Enable 37
[`rEu] Software Revision 71
[`r;hi] Range High 46, 57, 77
[``rh] Relative Humidty 47
[`r;Lo] Range Low 45, 56, 77
[rLoC] Read Lockout Security 70,
84
[roll], Rolling Password 85
[roll] Rolling Password 68, 70
[``rP] Ramp Action 54, 82
[`rP1] Ramping 27
[`rP1] Ramping 1 27
[`rP1] [`rP2] Ramping 1 or 2 27
[`r;rt] Ramp Rate 54, 82
[``r;r] Thermistor Resistance
Range 46
[`r;SC] Ramp Scale 54, 82
[`r;Sr] Retransmit Source 78
[`rt;L] RTD Leads 45
[`r;tp] Relative Temperature 47
[R;typ] Ramping Type 61
[S;bLd] Software Build 71
[`seC] 33
[`seC] Seconds 41
[`SEn] Sensor Type 45, 75, 77
[SFn;A] Source Function A 57
[`S;hi] Scale High 45, 56, 77, 78
[`Si;a] Event Input Source Instance
A 61
[`Si;B] Event Input Source Instance
B 61
[`SiL] Silence 83
[`S;Lo] Scale Low 45, 56, 77, 78
[SLoC] Set Lockout Security 70, 84
[``Sn] Serial Number 71
[s;stp] Profile Start Step 51
[`StP] Active Step 41
[S;tyP] Active Step Type 41
[`Su;A] Source Value A 35
[t;Agr] User Tune Aggressiveness
52, 74
[t;bnd] TRU-TUNE+™ Band 52, 75
[``t;C] Thermistor Curve 46
[``td] Time Derivative 38, 75, 81
[`t;gn] TRU-TUNE+™ Gain 52, 75
[``ti] Time Integral 38, 75, 80
[t;tUn] TRU-TUNE+™ Enable 52,
75
[tUn1] Tuning 27
[tUn1] [tUn2] Tuning 1 or 2 27
[tUn1] Tuning 1 27
[`UFA] User Failure Action 53
[UloC] Unlock Menu 85
[USr;r] User Restore Set 62, 74
[USr;S] User Save Set 62, 74
[WE;2] Wait Event 2 66
[2one] Zone 61
A
Absolute Temperature 47
AC Line Frequency 60, 82
A Conceptual View of the PM 4
Active Event Output (1 or 2) 41, 42
Active Step 41
Active Step Type 41
adaptive tuning 75
Address Modbus 62
Address Standard Bus 62, 63
Administrator Password 68, 70
agency approvals 3
alarm blocking 83
Alarm Menu 39, 57
alarms 82
Blocking 58, 83
deviation 82
Display 59
Hysteresis 58, 83
Latching 58, 83
Logic 58
process 82
set points 82
Sides 58
Silencing 59, 83
Source 57
Type 57
Alarm Type 82
Altitude Units 43
Analog Input Menu 34, 45
Assembly Definition
Addresses 93
Watlow EZ-ZONE ® PM PID Controller
•
99
•
Assembly Definition Addresses 86
Assembly Definition Addresses and
Assembly Working Addresses
93
Assembly Working Addresses 86,
93
Attention Codes 28
auto (closed loop) control 79
Autotune 74
Autotune Aggressiveness 52, 53
Autotune Request 37
Autotune Set Point 37, 74
autotuning 74–75
autotuning with TRU-TUNE+™ 75
B
Baud Rate 62
Blocking 58, 83
bumpless transfer 79
C
calibrating an analog input 76
Calibration Menu 71
Calibration Offset 34, 57, 76–77
changing the set point 28
Channel 62
chattering output 80
chemical compatibility 13
CIP (Common Industrial Protocol)
31
Closed Loop Set Point 37
Closed Loop Working Set Point 36
Communications Menu 62, 63, 65,
69
Setup Page 33, 43
Control 50, 55
Control Loop Menu 52
control methods 79
Control Mode 37, 79
Control Mode Active 36
Control Module Menus
Factory Page
Calibration Menu 71
Security Setting Menu 69, 71
Operations Page
Alarm Menu 39
Analog Input Menu 34
Digital Input/Output Menu 36
Linearization Menu 34
Loop Menu 37
Monitor Menu 36
Process Value Menu 35
Profile Status Menu 40
Setup Page
Alarm Menu 57
Analog Input Menu 45
Communications Menu 62, 63, 65,
69
Control Loop Menu 52
Digital Input/Output Menu 49
Appendix
Global Menu 60
Linearization Menu 46
Output Menu 55
Process Value 48
Cool Algorithm 52, 80
Cool Hysteresis 38, 80
Cool Output Curve 52, 79
Cool Power 36, 75
Cool Proportional Band 38, 75, 80
Custom Menu 74
D
Data Map 32, 63
Date of Manufacture 71
dead band 81
Dead Band 38, 81
Decimal 46
default Home Page parameters 26,
28
deviation alarms 82
Digital Input Function 60
Digital Input/Output Menu 36, 49
dimensions 9, 11
1/16 DIN 8
Direction 49
Display 59
Display Pairs 44, 62
displays 26
Display Time 62
Display Units 60
Down Key 26
E
Electrical Gain 76
Electrical Input Offset 72, 76
Electrical Input Slope 72, 76
Electrical Measurement 71, 76
Electrical Output Offset 72
Electrical Output Slope 72
End Set Point Value 67
Event Output (1 and 2) 67
EZ Key 84
F
Factory Page 68
Filter Time 46, 77
filter time constant 77
Function 43, 75
Function Instance 50, 52
Function Key Menu 84
G
Global Menu 60
Setup Page 33, 43
Guaranteed Soak Devia-
tion 44
Guaranteed Soak Deviation 61
Guaranteed Soak Enable 44, 61
H
Heat Algorithm 52, 80
Heat Hysteresis 37, 80
Heat Power 36, 75
Heat Proportional Band 37, 75, 80
High Power Scale 50, 56
high range 77
high scale 77
High Set Point
Alarm 39, 40, 83
Loop 54, 77
Home Page 28, 74
Hours 65
Hysteresis 58, 83
I
Idle Set Point 37
Input Error Failure 53, 79
Input Error Latching 46, 79
Input Error Status 34
input events 4
input features 76–78
calibration 76
Input Point 1 43
Input Point 2 43
Input Point 3 43
Input Point 4 43
Input Point 5 43
Input Point 6 43
Input Point 7 43
Input Point 8 43
Input Point 9 43
Input Point 10 43
inputs 4
Input Sensor Type 75
installation 12
Instance 60
IP Fixed Address Part 4 61, 62
J
Jump Count 67
Jump Count Remaining 42
Jump Step 66
K
keys and displays
1/16 DIN 26
L
Latching 58, 83
Level 59
Linearization 32, 45
Linearization Menu 34, 46
Locked Access Level 68, 70
Lock Operations Page 84
Lockout Menu 84
Lock Profiling Page 84
Logic 58
Loop Menu 37
Low Power Scale 50, 55
low range 77
low scale 77
Low Set Point
Wat low EZ-ZONE ® PM PID Controller
•
100
•
Alarm 39, 83
Loop 54, 77
M
Manual Control Indicator Light 79
manual (open loop) control 79
manual tuning 75
Message Action 27
message, display 27
Minutes 65, 66
Modbus Default Assembly Structure
80-119 94
Modbus - Programmable Memory
Blocks 93
Modbus Word Order 63
Monitor Menu 36
N
navigating
Factory Page 68
pages and menus 30
Profiling Page 64
Setup Page 33, 43
network wiring 23
no-arc relay 78
Non-volatile Save 44
O
on-off control 80
Open Loop Detect Deviation 54
Open Loop Detect Enable 53
Open Loop Detection 83
Open Loop Detect Time 53
Open Loop Set Point 38
Operations Page 33
output configuration 79
output features 77
Output Function 56, 78
Output Menu 55
Output Point 1 43
Output Point 2 43
Output Point 3 43
Output Point 4 43
Output Point 5 43
Output Point 6 43
Output Point 7 43
Output Point 8 43
Output Point 9 43
Output Point 10 43
output power scaling 78
outputs 4
Output State 36
Output Type 56, 78
P
P3T armor sealing system 3
Parameter 1 to 20 69
Parameter ID 31
Parity 63
Part Number 71
Password 71
Appendix
Password Enable 68
Peltier Delay 43, 53
Power Out Time 44, 61
Pressure Units 43
process alarms 82
Process Error Enable 46
Process Error Low 46
Process Value 34, 48
Process Value Active 36
Process Value Menu 35
Profibus 32
Profibus Index 31
Profile Status Menu 40
Profile Type 61
Profiling Page 64
profiling parameters 64
programming the Home Page 74
proportional control 80
plus integral (PI) control 80
plus integral plus derivative (PID)
control 81
Protocol 62
Public Key 68, 71
Q
R
Ramp Action 54
Ramp Rate 54, 82
Ramp Scale 54, 82
Range High 46, 57, 77
Range Low 45, 56, 77
Read Lockout Security 84
Real Time Clock 32, 44
Relative Humidty 47
Relative Temperature 47
Remote Enable 37
removing mounted controller 12
responding to a displayed message
27–28
restoring user settings 74
retransmit 77
Retransmit Source 56, 78
Rolling Password 68, 70
RTD Leads 45
S
saving user settings 74
Scale High 45, 56, 77, 78
Scale Low 45, 56, 77, 78
Seconds 65
secure settings 84, 85
Security Setting 69, 71
sensor selection 77
Sensor Type 45, 75, 77
Serial Number 71
Set Lockout Security 84
set point high limit 77
Set Point High Limit Open Loop 54
set point low limit 77
Set Point Low Limit Open Loop 54
Setup Page 43
Sides
Alarm 58
Silencing 59, 83
single set point ramping 82
Software Build 71
Software Revision 71
Source 57
System Security 85
T
Target Set Point 65
temperature units indicator lights 26
Thermistor 18, 45
Time Base 50, 55
Time Derivative 38, 75, 81
Time Integral 38, 75, 80
TRU-TUNE+™ Band 52, 75
TRU-TUNE+™ Enable 52, 75
TRU-TUNE+™ Gain 52, 75
tuning the PID parameters 74
Type 57
output 1 switched dc/open collector
19, 20
output 1 universal process 20
output 2 mechanical relay, form
A 22
output 2 no-arc relay, form A 22
output 2 solid-state relay, form A
22
output 2 switched DC/open collector 21
output 3 switched dc/open collector 23
Standard Bus EIA-485 communications 23
X
Y
Z
Zone Display 62
U
upper display 26
User Failure Action 53
User Password 68, 70
User Restore Set 62, 74
User Save Set 62, 74
User Tune Aggressiveness 74
Using EZ-ZONE® Configurator Software 87
using the software 84
V
variable time base 81
W
Wait Event (1 and 2) 66
Wait For Process Instance 66
Wait For Time 65
weight 96
wiring
digital input or output 5 16
high power 16
input 1 potentiometer 17
input 1 process 17
input 1 RTD 17
input 1 thermocouple 17
input 2 thermocouple 18
low power 16
Modbus RTU or Standard Bus EIA485 communications 23
output 1 mechanical relay, form C
20
output 1 solid-state relay, form A
21
Watlow EZ-ZONE ® PM PID Controller
•
101
•
Appendix
Declaration of Conformity
Series EZ-ZONE® PM
WATLOW
an ISO
1241 Bundy Blvd.
Winona, MN 55987 USA
9001 approved facility since 1996.
Declares that the following product:
Designation:
Series EZ-ZONE® PM (Panel Mount)
Model Numbers:
PM (3, 6, 8, 9 or 4)(Any Letter or number) – (1, 2, 3 or 4)(A, C, E, F or
K) (A, C, H, J or K)(Any letter or number) – (Any letter or number)(A, C,
E, F or K)(A, C, H, J or K) (Any three letters or numbers)
Classification:
Temperature control, Installation Category II, Pollution degree 2, IP66
Rated Voltage and Frequency: 100 to 240 V~ (ac 50/60 Hz) or 15 to 36 VÎ dc/ 24 V~ac 50/60 Hz
Rated Power Consumption:
10 VA maximum PM3, PM6 Models.
14 VA maximum PM8, PM9, PM4 Models
Meets the essential requirements of the following European Union Directives by using the relevant
standards show below to indicate compliance.
2004/108/EC Electromagnetic Compatibility Directive
EN 61326-1
2006
EN 61000-4-2
EN 61000-4-3
EN 61000-4-4
EN 61000-4-5
EN 61000-4-6
EN 61000-4-11
EN 61000-3-2
EN 61000-3-31
SEMI F47
1996 +A1,A2
2006
2004
2006
1996 +A1,A2,A3
2004
2006
2005
2000
Electrical equipment for measurement, control and laboratory
use – EMC requirements (Industrial Immunity, Class B
Emissions).
Electrostatic Discharge Immunity
Radiated Field Immunity 10V/M 80–1000 MHz, 3 V/M 1.4–2.7 GHz
Electrical Fast-Transient / Burst Immunity
Surge Immunity
Conducted Immunity
Voltage Dips, Short Interruptions and Voltage Variations Immunity
Harmonic Current Emissions
Voltage Fluctuations and Flicker
Specification for Semiconductor Sag Immunity Figure R1-1
1
For mechanical relay loads, cycle time may need to be extended up to 160 seconds to meet flicker
requirements depending on load switched and source impedance.
EN 61010-1
2006/95/EC Low-Voltage Directive
2001
Safety Requirements of electrical equipment for measurement,
control and laboratory use. Part 1: General requirements
Compliant with 2002/95/EC RoHS Directive
Per 2002/96/EC W.E.E.E Directive
Please Recycle Properly.
Raymond D. Feller III
Name of Authorized Representative
Winona, Minnesota, USA
Place of Issue
General Manager
Title of Authorized Representative
June 2009
Date of Issue
Signature of Authorized Representative
CE DOC EZ-ZONE PM-06-09
Wat low EZ-ZONE ® PM PID Controller
•
102
•
Appendix
How to Reach Us
Corporate Headquarters
Watlow Electric Manufacturing Company
12001 Lackland Road
St. Louis, MO 63146
Sales: 1-800-WATLOW2
Manufacturing Support: 1-800-4WATLOW
Email: info@watlow.com
Website: www.watlow.com
From outside the USA and Canada:
Tel: +1 (314) 878-4600
Fax: +1 (314) 878-6814
Latin America
Watlow de México S.A. de C.V.
Av. Fundición No. 5
Col. Parques Industriales
Querétaro, Qro. CP-76130
Mexico
Tel: +52 442 217-6235
Fax: +52 442 217-6403
Europe
Watlow France
Tour d'Asnières.
4 Avenue Laurent Cély
92600 Asnières sur Seine
France
Tél: + 33 (0)1 41 32 79 70
Télécopie: + 33(0)1 47 33 36 57
Email: info@watlow.fr
Website: www.watlow.fr
Watlow GmbH
Postfach 11 65, Lauchwasenstr. 1
D-76709 Kronau
Germany
Tel: +49 (0) 7253 9400-0
Fax: +49 (0) 7253 9400-900
Email: info@watlow.de
Website: www.watlow.de
Watlow Italy S.r.l.
Viale Italia 52/54
20094 Corsico MI
Italy
Tel: +39 024588841
Fax: +39 0245869954
Email: italyinfo@watlow.com
Website: www.watlow.it
Asia and Pacific
Watlow Ibérica, S.L.U.
C/Marte 12, Posterior, Local 9
E-28850 Torrejón de Ardoz
Madrid - Spain
T. +34 91 675 12 92
F. +34 91 648 73 80
Email: info@watlow.es
Website: www.watlow.es
Watlow UK Ltd.
Linby Industrial Estate
Linby, Nottingham, NG15 8AA
United Kingdom
Telephone: (0) 115 964 0777
Fax: (0) 115 964 0071
Email: info@watlow.co.uk
Website: www.watlow.co.uk
From outside The United Kingdom:
Tel: +44 115 964 0777
Fax: +44 115 964 0071
Watlow Singapore Pte Ltd.
16 Ayer Rajah Crescent,
#06-03/04,
Singapore 139965
Tel: +65 6773 9488Fax: +65 6778 0323
Email: info@watlow.com.sg Website: www.watlow.com.sg
Watlow Korea Co., Ltd.
#1406, E&C Dream Tower, 46, Yangpyeongdong-3ga
Yeongdeungpo-gu, Seoul 150-103
Republic of Korea
Tel: +82 (2) 2628-5770
Fax: +82 (2) 2628-5771
Website: www.watlow.co.kr
Watlow Australia Pty., Ltd.
4/57 Sharps Road
Tullamarine, VIC 3043
Australia
Tel: +61 3 9335 6449
Fax: +61 3 9330 3566
Website: www.watlow.com
Watlow Malaysia Sdn Bhd
No. 14-3 Jalan 2/114
Kuchai Business Centre
Jalan Kuchai Lama
58200 Kuala Lumpur
Malaysia
Tel: +60 3 7980 7741 Fax: +60 3 7980 7739
Watlow Electric Manufacturing (Shanghai) Company
1118 Fangyuan Road, Anting Industrial Park, Jiading, Shanghai,
PRC 201203
People’s Republic of China
Tel: +86 21 39509510
Fax: +86 21 5080-0906
Email: info@watlow.cn
Website: www.watlow.cn
瓦特龍電機股份有限公司
80143 高雄市前金區七賢二路189號 10樓之一
電話: 07-2885168
傳真: 07-2885568
Watlow Electric Taiwan Corporation
10F-1 No.189 Chi-Shen 2nd Road Kaohsiung 80143
Taiwan
Tel: +886-7-2885168 Fax: +886-7-2885568
ワトロー・ジャパン株式会社
〒101-0047 東京都千代田区内神田1-14-4
四国ビル別館9階
Tel: 03-3518-6630 Fax: 03-3518-6632
Email: infoj@watlow.com
Website: www.watlow.co.jp
Your Authorized Watlow Distributor
Watlow Japan Ltd.
1-14-4 Uchikanda, Chiyoda-Ku
Tokyo 101-0047
Japan
Tel: +81-3-3518-6630 Fax: +81-3-3518-6632
Email: infoj@watlow.com Website: www.watlow.co.jp
TOTAL
CUSTOMER
SATISFACTION
3 Year Warranty
Watlow EZ-ZONE ® PM PID Controller
•
103
•
Appendix
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising