Christie | LX400 | User manual | Christie LX400 User manual

Christie LX400 User manual
LX400
U S E R M A N U A L - O P E R AT I N G G U I D E
(Concise)
020-000166-0
《ENGLISH》
NOTICE for European Union members
This is a Class A product in European Union.
WARNING :
This is a Class A product. In a domestic environment this product may cause radio
interference in which case the user may be required to take adequate measures.
AVIS pour les membres du Union Européenne
《FRANÇAIS》
Le présent appareil est un produit de classe A, dans Union Européenne.
AVERTISSEMENT :
Le présent appareil est un produit de classe A. En environnement domestique, ce produit
est susceptible de provoquer des interférences radio-électriques, auquel cas l’utilisateur
devra prendre les mesures adéquates.
BEACHTUNG für Europäischen Union-Mitglieder
Dies ist ein Produkt der Klasse A, in Europäischen Union.
《DEUTSCH》
WARNUNG :
Dies ist ein Produkt der Klasse A. Bei der Verwendung im häuslichen Bereich können
Störungen des Radio- oder Fernsehempfangs auftreten. Beim Auftreten derartiger
Störungen hat der Benutzer gegebenenfalls Abhilfemaßnahmen zu treffen.
AVISO para los miembros de Unión Europea
Este es un producto de Clase A, en Unión Europea
《ESPAÑOL》
ADVERTENCIA :
Este es un producto de Clase A. En un entorno doméstico este producto puede causar
radio interferencias, en cuyo caso el usuario deberá tomar las medidas pertinentes.
DICHIARAZIONE per membri di Unione europea
Questo è un prodotto di Classe A, negli Unione europea.
《ITALIANO》
AVVERTENZA :
Questo è un prodotto di Classe A. In un ambiente domestico, questo prodotto potrebbe
causare interferenze radio, nel cui caso l’utente è obbligato a prendere gli adeguati
provvedimenti.
BEMERK for EU-medlemmer
Dette er et klasse A produkt, i EU.
《NORSK》
ADVARSEL :
Dette er et klasse A produkt. I et hjemmemiljø kan dette produktet forårsake
radiointerferens, og i dette tilfellet anbefales det at brukeren tar tilstrekkelige
forholdsregler.
OPMERKING voor de Europese Unie leden
Dit is een klasse A product, in Europese Unie.
《NERDERLANDS》
WAARSCHUWING :
Dit is een klasse A product. In een huiselijke omgeving kan dit product radiointerferentie veroorzaken. De gebruiker is dan verplicht om maatregelen te nemen om de
interferentie te ongedaan te maken.
NOTIFICAÇÃO para sócios de União europeus
Trata-se de um produto Classe A, em União européia.
《PORTUGUÊS》
AVISO :
Trata-se de um produto Classe A. Num ambiente doméstico, este produto pode provocar
interferências rádio, podendo ser necessário tomar medidas adequadas.
䗮ⶹ⃻⌆㘨ⲳ៤ਬ
《Ё᭛》
ᴀѻકᰃ $ 㑻ѻક೼⃻⌆㘨ⲳ (8
䄺ਞ
ᴀѻકᰃ $ 㑻ѻકDŽ೼ᆊᒁ⦃๗Ёˈᴀѻકৃ㛑Ӯᇐ㟈᮴㒓⬉ᑆᡄˈ䖭⾡ᚙ‫މ‬ϟˈ
⫼᠋䳔䞛প䗖ᔧⱘ᥾ᮑDŽ
氦崃͑櫶穯͙͑ͶΆ͚͑儆沋͑箒毖櫖͑堆穢͑皻滆͑
《穢剳檺》
決冉汆͑氦崃͑櫶穯͙͑ͶΆ͚͑櫖昢͑畺岞枪͑Ͳ͑洢禎沋城埪 .
凃処 :
懾͑洢禎汆͑畺岞枪͑Ͳ͑洢禎沋城埪 ͑͟懾͑洢禎汆͑其渂͑筞凃͑喺櫖昢͑斲殯沖汞
洇洎穢͑浶獞庂͑穊殚嵢͑穞垚͑怺昦͑儊昳汊͑氦愢穦͑朞͑沎枻城埪 ͟
ANMÄRKNING för EU-medlemmar
Detta är en klass A-produkter, i EU.
《SVENSKA》
VARNING :
Detta är en klass A-produkt. I hemmiljö kan denna produkt orsaka radiostörningar mot
vilka användaren måste vidta åtgärder.
ПРЕДОСТЕРЕЖЕНИЕ для членов Европейском Союзе (EC) 《РУССКИЙ》
Это изделие Класса А, в Европейском Союзе (EC).
ПРЕДУПРЕЖДЕНИЕ :
Это изделие Класса А. В бытовых условиях это изделие может стать причиной
возникновения радиопомех, в случае чего пользователь должен предпринять
соответствующие меры.
HUOMAA ajaksi Euroopan Unionin jäseniä
Tämä on luokan A tuote on Euroopan unionin.
《SUOMI》
VAROITUS :
Tämä laite on luokan A tuote. Kotikäytössä tämä tuote saattaa aiheuttaa radiohäiriötä.
Käyttäjän on tällöin ehkä ryhdyttävä korjaaviin toimenpiteisiin.
UWAGA dla członków Unii Europejskie
Jest to produkt klasy A, w Unii Europejskiej.
《POLSKI》
ZAGROŻENIE :
Jest to produkt klasy A. W środowisku domowym może on wywoływać zakłócenia
radiowe, co oznacza, że użytkownik będzie musiał podjąć odpowiednie środki zaradcze.
Projector
LX400
User Manual - Operating Guide (concise)
Thank you for purchasing this projector.
WARNING
►Before using this product, be sure to read all manuals for this product. See
“Using the CD manual” (12) to read the manuals in the CD. After reading them,
store them in a safe place for future reference.
Contents
Contents of package........................... 1
Arrangement ....................................... 2
Connecting your devices .................... 3
Connecting power supply ................... 4
Turning on the power .......................... 4
Adjusting the projector’s elevator ....... 5
Remote control ................................... 5
Displaying the picture ......................... 7
Turning off the power .......................... 7
Lamp................................................... 8
Air filter ............................................. 10
Internal clock battery ........................ 11
Using the CD manual ....................... 12
Regulatory notices ............................ 13
Specifications ................................... 14
Warranty and after-service ............... 15
Contents of package
Your projector should come with the items shown
below. Check that all the items are included. Contact
to your dealer immediately if any items are missing.
(1) Remote control with two AA batteries
(2) Power cord
(3) RGB cable
(4) Lens cover and Rivet and Strap
(5) User’s manuals (Book x1, CD x1)
(6) Security label
(2)
(1)
(3)
(4)
(5)
(6)
CAUTION
►Keep the original packing materials for future reshipment. Be sure to use the
original packing materials when moving the projector. Use special caution for the
lens.
LX400 User Manual - Concise
1
020-000166-02 Rev. 1 (08-2009)
Arrangement
Please arrange the projector and the screen.
Install the projector in a stable, cool and airy place, keeping a space of 30 cm or more
between the sides of the projector and other objects such as walls. Avoid the projector
from a hot, humid, dusty, or smoky place.
Refer to the illustrations and tables below to determine screen size and projection distance.
The values shown in the table are calculated for a full size screen: 1024×768
(a) Screen size (diagonal)
(b) Projection distance (±10%)
(c) Screen height (±10%), when the vertical lens shift is set full upward.
On a horizontal surface
(b)
(a)
(c) up
(c) down
Suspended from the ceiling
(c) down
(a)
• Consult with your dealer before
a special installation such as
suspending from a ceiling.
(c) up
(b)
(a) Screen
size
[inch (m)]
4 : 3 screen
(b) Projection distance
(c) Screen height
[m (inch)]
[cm (inch)]
min.
max.
down
up
30
(0.8)
0.9
(35)
40
60
70
80
90
100
120
150
200
250
300
350
(1.0)
(1.5)
(1.8)
(2.0)
(2.3)
(2.5)
(3.0)
(3.8)
(5.1)
(6.4)
(7.6)
(8.9)
1.2
1.8
2.1
2.4
2.7
3.0
3.7
4.6
6.1
7.7
9.2
10.8
(47) 1.4 (57)
(71) 2.2 (86)
(83) 2.6 (100)
(96) 2.9 (115)
(108) 3.3 (130)
(120) 3.7 (144)
(144) 4.4 (174)
(181) 5.5 (217)
(241) 7.4 (291)
(302) 9.2 (364)
(363) 11.1 (437)
(424) 13.0 (510)
1.1
(42)
5
6
9
11
12
14
15
18
23
30
38
46
53
(2)
(2)
(4)
(4)
(5)
(5)
(6)
(7)
(9)
(12)
(15)
(18)
(21)
41
55
82
96
110
123
137
165
206
274
343
411
480
16 : 9 screen
(b) Projection distance
(c) Screen height
[m (inch)]
[cm (inch)]
min.
max.
down
up
(16) 1.0 (38) 1.2 (46)
-1
(22) 1.3 (51) 1.6 (62)
-2
(32) 2.0 (78) 2.4 (94)
-2
(38) 2.3 (91) 2.8 (110) -3
(43) 2.6 (104) 3.2 (126) -3
(49) 3.0 (117) 3.6 (141) -4
(54) 3.3 (131) 4.0 (157) -4
(65) 4.0 (157) 4.8 (189) -5
(81) 5.0 (197) 6.0 (237) -6
(108) 6.7 (263) 8.0 (317) -8
(135) 8.4 (329) 10.1 (396) -10
(162) 10.0 (395) 12.1 (476) -12
(189) 11.7 (462) 14.1 (556) -15
(0)
(-1)
(-1)
(-1)
(-1)
(-1)
(-2)
(-2)
(-2)
(-3)
(-4)
(-5)
(-6)
39
51
77
90
103
116
129
154
193
257
322
386
450
(15)
(20)
(30)
(35)
(41)
(46)
(51)
(61)
(76)
(101)
(127)
(152)
(177)
WARNING
►Install the projector in a stable horizontal position.
►Place the projector in a cool place, and ensure that there is sufficient
ventilation.
►Do not place the projector any place where it may get wet.
CAUTION
►Avoid placing the projector in smoky, humid or dusty place.
►Position the projector to prevent light from directly hitting the projector’s remote
sensor.
LX400 User Manual - Concise
2
020-000166-02 Rev. 1 (08-2009)
Connecting your devices
Before connecting devices, please read the manuals for all the devices that you want to
connect with this projector, to make sure that the connection is proper and prepare the
connectors needed. And connect them properly according to the manuals.
AUDIO OUT
RGB OUT
RS-232C
RGB OUT
AUDIO OUT
LAN
HDMI
USB-A
PC
USB storage
SD card
Remote
control
LAN
RGB1
RGB
OUT
Y
HDMI
CB/PB
VIDEO
Monitor
LASER
INDICATOR
CR/PR
AUDIO IN 1
AUDIO IN 2
BLANK
RGB2
LASER
G/Y B/CB/PB B/CR/PR
ASPECT
PUSH
H
R
L AUDIO OUT
AUDIO IN 4
REMOTE
CONTROL
USB
Speakers
(with an
amplifier)
CONTROL
RGB IN
R
L
AUDO IN 3
ENTER
V
AUDIO IN
S-VIDEO OUT
R
L
AUDO IN OUT
VIDEO OUT
R
L
AUDO IN OUT
Y
CB/PB
CR/PR
COMPONENT VIDEO OUT
R
L
AUDO IN OUT
VCR/DVD player
WARNING
►Do not disassemble or modify the projector and accessories.
►Be careful not to damage the cables, and do not use damaged cables.
CAUTION
►Turn off all devices and unplug their power cords prior to connecting them to
projector.
►Use appropriate accessory or designated cables. Ask your dealer about nonaccessory cables which may be required a specific length or a ferrite core by
the regulations. For cables with a core only at one end, connect the end with the
core to the projector.
►Make sure that devices are connected to the correct ports.
►For safety, do not connect the LAN port to any network that might have
excessive voltage.
LX400 User Manual - Concise
3
020-000166-02 Rev. 1 (08-2009)
Connecting power supply
1. Connect the connector of the power cord to the AC
inlet of the projector.
2. Firmly plug the power cord's plug into the outlet.
AC inlet
Connector of the
power cord
to the outlet
WARNING
►Please use extra caution when connecting the power cord, as incorrect or
faulty connections may result in fire and/or electrical shock.
• Only use the power cord that came with the projector. If it is damaged, contact
your dealer to newly get correct one.
• Only plug the power cord into an outlet whose voltage is matched to the power
cord. The power outlet should be close to the projector and easily accessible.
Remove the power cord for complete separation.
• Never modify the power cord.
Turning on the power
STANDBY/ON button
1. Make sure that the power cord is firmly and correctly
POWER indicator
connected to the projector and the outlet.
2. Remove the lens cover, and set the power switch to the
ON position (marked “ I ”).
The power indicator will light up in steady orange. Then
wait several seconds because the buttons may not
function for these several seconds.
3. Press the STANDBY/ON button on the projector or the
remote control.
The projection lamp will light up and the POWER indicator will
Power
switch
begin blinking in green. When the power is completely on, the
indicator will stop blinking and light in steady green.
WARNING
►A strong light is emitted when the projector’s power is on. Do not look into the
lens of the projector or look inside of the projector through any of the projector’s
openings.
NOTE
• When the AUTO ON in the OPTION menu is set to the TURN ON, and the power was
turned off by the power switch last time, turning the power switch on makes the projection
lamp light on without pushing the STANDBY/ON button. For more information, please
see the “Operating Guide” in the CD.
LX400 User Manual - Concise
4
020-000166-02 Rev. 1 (08-2009)
Adjusting the projector's elevator
Use the elevator feet to place the projector horizontally. Using the feet
can also tilt the projector in order to project at a suitable angle to the
screen, elevating the front side of the projector within 8 degrees.
This projector has 2 elevator feet and 2 elevator knobs. An elevator
foot is adjustable while pulling up the elevator knob on the same side
as it.
1. To loose an elevator foot, pull up the elevator knob on the same
side as it.
8°
2. Position the front side of the projector to the desired height.
3. Release the elevator knobs in order to lock the elevator feet.
4. To finely adjust, twist the foot.
WARNING
►Do not handle the elevator knobs without holding the projector, since the
projector may drop down.
►Do not tilt the projector other than elevating its front within 8 degrees using
the adjuster feet. A tilt of the projector exceeding the restriction could cause
malfunction or shortening the lifetime of consumables, or the projector itself.
Remote control
Laser pointer
The laser beam is emitted and the LASER INDICATOR lights while the LASER button is
pressed.
The laser beam outlet
LASER INDICATOR
LASER button
WARNING
►Never hit an eye with the laser beam, and use the laser pointer except to
serve as a pointer to a screen. The laser beam can cause vision problems, and
also may cause radiation exposure.
LX400 User Manual - Concise
5
020-000166-02 Rev. 1 (08-2009)
Remote control (continued)
Putting batteries
Please load the batteries before using the remote control.
1. Slide back and remove the battery cover.
2. Put the two AA batteries (HITACHI MAXELL, Part No.LR6 or R6P)
into the holder, according to the polarity markings (+) and (-) on the
holder.
3. Put the battery cover back to its former state.
WARNING
►Always handle the batteries with care and use them only as directed. Improper
use may result in battery explosion, cracking or leakage, which could result in
fire, injury and/or pollution of the surrounding environment.
• Be sure to use only the batteries specified. Do not use batteries of different
types at the same time. Do not mix a new battery with used one.
• Make sure the plus and minus terminals are correctly aligned when loading a
battery.
• Keep a battery away from children and pets.
• Do not recharge, short circuit, solder or disassemble a battery.
• Do not allow a battery in a fire or water. Keep batteries in a dark, cool and dry
place.
• If you observe battery leakage, wipe out the leakage and then replace a battery.
If the leakage adheres to your body or clothes, rinse well with water immediately.
• Obey the local laws on disposing the battery.
(1) VIDEO button
(2) RGB button
(3) BLANK button
(4) ASPECT button
(5) AUTO button
(6) POSITION button
(7) VOLUME button
(8) MAGNIFY - ON button
(9) MAGNIFY - OFF button
(10) MUTE button
(11) FREEZE button
(12) KEYSTONE button (13) SEARCH button
(14) MENU button
(15) Lever switch : acting 3 functions as below.
Cursor button ▲ : to slide toward the side marked ▲.
Cursor button ▼ : to slide toward the side marked ▼.
ENTER button : to push down the center point.
(16) Cursor button ◄
(17) Cursor button ►
(18) RESET button
(19) ESC button
LX400 User Manual - Concise
6
(1)
(2)
LASER
INDICATOR
STANDBY/ON
(3)
VIDEO
BLANK
RGB
LASER
(4)
(15)
(17)
ASPECT
(16)
(14)
(19)
(6)
(8)
(9)
(11)
(12)
PUSH
ENTER
PAGE UP
ESC
PAGE DOWN
MENU
POSITION
AUTO
MAGNIFY
MY BUTTON
ON
1
OFF
2
FREEZE
KEYSTONE
RESET
VOLUME
MUTE
SEARCH
(18)
(5)
(7)
(10)
(13)
020-000166-02 Rev. 1 (08-2009)
Displaying the picture
INPUT button
1. Make sure that the signal source is sending the signal to
the projector.
2. Press the VOLUME button on the remote control. Use
the ▲/▼ cursor buttons to adjust the volume.
3. Press the INPUT button on the projector.
Each time you press the button, the projector switches
its input port in turn.
4. Press the ASPECT button on the remote control. Each
time you press the button, the projector switches the
mode for aspect ratio in turn.
5. Use the zoom ring to adjust the screen size.
ASPECT
button
Zoom ring
Focus ring
6. Use the focus ring to focus the picture.
Top
7. Use the vertical lens shift dial to shift the picture upward
or downward. It is recommended to adjust the picture
upward.
8. Use the horizontal lens shift dial to shift the picture left or
right.
UP
DOWN
LEFT
Turning off the power
Lens shift cover
RIGHT
STANDBY/ON button
1. Press the STANDBY/ON button on the projector or the
POWER indicator
remote control.
The message “Power off?” will appear on the screen for
about 5 seconds.
2. Press the STANDBY/ON button on the projector or the
remote control again while the message appears.
The projector lamp will go off, and the POWER indicator
will begin blinking in orange.
Then the POWER indicator will stop blinking and light in
Power
steady orange when the lamp cooling is complete.
switch
3. Make sure that the power indicator lights in steady
orange, and set the power switch to the OFF position
(marked “O”).
The POWER indicator will go off. Attach the lens cover.
Do not turn the projector on for 10 minutes or more after turning it off. Turning the projector
on again too soon could shorten the lifetime of some consumable parts of the projector.
WARNING
►Do not touch around the lamp cover and the exhaust vents during use or just
after use, since it is too hot.
LX400 User Manual - Concise
7
020-000166-02 Rev. 1 (08-2009)
Lamp
A lamp has finite product life. Using the lamp for long periods of time could cause the
pictures darker or the color tone poor. Note that each lamp has a different lifetime, and
some may burst or burn out soon after you start using them.
Preparation of a new lamp and early replacement are recommended. To prepare a new
lamp, contact your dealer and tell the lamp type number.
Type number = 003-120457-01 (DT00873)
Replacing the lamp
1. Turn the projector off, and unplug the power cord. Allow
the projector to cool for at least 45 minutes.
2. Prepare a new lamp.
If the projector is mounted on a ceiling, or if the lamp
has broken, also ask the dealer to replace the lamp.
In case of replacement by yourself,
3. Loosen the screw (marked by arrow) of the lamp cover
and then slide the lamp cover to the side to remove it.
4. Loosen the 3 screws (marked by arrow) of the lamp,
and slowly pick up the lamp by the handles.
5. Insert the new lamp, and retighten firmly the 3 screws
of the lamp that are loosened in the previous process
to lock it in place.
6. Slide the lamp cover back in place and firmly fasten the
screw of the lamp cover.
7. Turn the projector on and reset the lamp time using the
LAMP TIME item in the OPTION menu.
(1) Press the MENU button to display a menu.
(2) Point at the “Go to Advanced Menu …” in the menu
using the ▼/▲ button, then press the ► button.
(3) Point at the “OPTION” in the left column of the menu
using the ▼/▲button, then press the ► button.
(4) Point at the “LAMP TIME” using the ▼/▲ button,
then press the ► button. A dialog will appear.
(5) Press the ▲ button to select “RESET” on the dialog.
It performs resetting the lamp time.
The lamp cover
The handles
NOTE
• Please reset the lamp time only when you have replaced the lamp, for a suitable
indication about the lamp.
LX400 User Manual - Concise
8
020-000166-02 Rev. 1 (08-2009)
Lamp (continued)
Lamp warning
HIGH VOLTAGE
HIGH TEMPERATURE
HIGH PRESSURE
►The projector uses a high-pressure mercury glass lamp. The lamp can break
with a loud bang, or burn out, if jolted or scratched, handled while hot, or worn
over time. Note that each lamp has a different lifetime, and some may burst or
burn out soon after you start using them. In addition, when the bulb bursts, it is
possible for shards of glass to fly into the lamp housing, and for gas containing
mercury to escape from the projector’s vent holes.
• If the lamp should break (it will make a loud bang when it does),
Disconnect
the plug from
the power
outlet
Unplug the power cord from the outlet, and make sure to request
a replacement lamp from your local dealer. Note that shards of
glass could damage the projector’s internals, or cause injury during
handling, so please do not try to clean the projector or replace the
lamp yourself.
Ventilate the room well, and make sure not to breathe the gas that
comes out of the projector vents, or get it in your eyes or mouth.
• Before replacing the lamp, turn the projector off and unplug the
power cord, then wait at least 45 minutes for the lamp to cool
sufficiently. Handling the lamp while hot can cause burns, as well as
damaging the lamp.
• Never unscrew except the appointed (marked by an arrow) screws.
• Do not open the lamp cover while the projector is suspended from
a ceiling. This is dangerous, since if the lamp’s bulb has broken, the
shards will fall out when the cover is opened. In addition, working in
high places is dangerous, so ask your local dealer to have the lamp
replaced even if the bulb is not broken.
• Do not use the projector with the lamp cover removed. At the lamp
replacing, make sure that the screws are screwed in firmly. Loose
screws could result in damage or injury.
• Use only the lamp of the specified type.
• If the lamp breaks soon after the first time it is used, it is possible
that there are electrical problems elsewhere besides the lamp. If this
happens, contact your local dealer or a service representative.
• Handle with care: jolting or scratching could cause the lamp bulb to
burst during use.
• Using the lamp for long periods of time, could cause it dark, not
to light up or to burst. When the pictures appear dark, or when the
color tone is poor, please replace the lamp as soon as possible. Do
not use old (used) lamps; this is a cause of breakage.
► About disposal of a lamp: This product contains a mercury lamp; do not put
it in a trash. Dispose of it in accordance with environmental laws.
· For lamp recycling, go to www.lamprecycle.org (in the US).
· For product disposal, contact your local government agency or www.eiae.org
(in the US) or www.epsc.ca (in Canada).
For more information, call your dealer.
LX400 User Manual - Concise
9
020-000166-02 Rev. 1 (08-2009)
Air filter
Please check and clean the air filter periodically. When the indicators or a message
prompts you to clean the air filter, comply with it as soon as possible. The air filter has two
kinds of filters inside. Replace the filters when they are damaged or too soiled. To prepare
the new filters, make contact with your dealer and tell the following type number.
Type number = 003-002119-01 (MU05661)
When you replace the lamp, please replace the air filter. An air filter of specified type will
come together with a replacement lamp for this projector.
1. Turn the projector off, and unplug the power cord. Allow the
projector to sufficiently cool down.
2. Use a vacuum cleaner on and around the filter cover.
3. Pull the filter cover knobs while lifting it, to take the filter unit
off.
4. Use a vacuum cleaner for the filter vent of the projector and
both sides of the filter unit.
If the filters are damaged or too soiled, replace them according
to the following procedure number 5 to 7. Otherwise, please
jump to the procedure number 8.
5. Pull the filter frame’s knob up while holding the filter cover to
remove the filter frame, then take the filters out.
6. Set new filters where former filters were. Put the larger
meshed filter into a filter cover first. Then put the finer meshed
filter on the larger meshed one.
7. Put the filter frame back where it was.
8. Put the filter unit back into the projector.
9. Turn the projector on and reset the filter time using the FILTER
TIME item in the EASY MENU
(1) Press the MENU button to display a menu.
(2) Point at the “FILTER TIME” using the ▼/▲ button, then
press the ► button. A dialog will appear.
(3) Press the ▲ button to select RESET on the dialog. It
performs resetting the filter time.
Filter cover
Filter cover knobs
Filter unit
Filter frame
Filter (finer meshed)
Filter (larger meshed)
Filter cover
WARNING
►Before taking care of the air filter, make sure the power cable is not plugged
in, then allow the projector to cool sufficiently.
►Use only the air filter of the specified type. Do not use the projector without the
air filter or the filter cover. It could result in a fire or malfunction to the projector.
►Clean the air filter periodically. If the air filter becomes clogged by dust or the like,
internal temperatures rise and could cause a fire, a burn or malfunction to the projector.
NOTE
• Please reset the filter time only when you have cleaned or replaced the air filter, for a
suitable indication about the air filter.
• The projector may display the message such as “CHECK THE AIR FLOW” or turn off
the projector, to prevent the internal heat level rising.
LX400 User Manual - Concise
10
020-000166-02 Rev. 1 (08-2009)
Internal clock battery
Consumption of the battery makes the clock not to work correctly. When the clock is wrong
or it has stopped, please replace the battery according to the following procedures.
1. Turn the projector off, and unplug the power cord. Allow the
projector to cool sufficiently.
2. After making sure that the projector has cooled adequately, slowly
turn over the projector, so that the bottom is facing.
3. Turn the battery cover fully in the direction indicated “OPEN” using
Battery Cover
a coin or the like, and pick the cover up to remove it.
4. One of two kinds of clock battery holder, A or B shown to the
90°
right, is inside the battery cover.
For A holder:
Pry up the battery using a flathead screwdriver or the like to
take it out. While prying it up, put a finger lightly on the battery
since it may pop out of the holder.
For B holder:
Press the metal claw of the battery holder putting a finger
lightly on the battery since it may pop out of the holder. Then
the battery will come up. Remove the battery.
5. Replace the battery with a new HITACHI MAXELLL, Part No.
CR2032 or CR2032H.
Slide the battery in under the plastic claw, and push it into the
holder until it clicks.
6. Replace the battery cover in place, then turn it in the direction
indicated “CLOSE” using such as coins, to fix.
90°
OPEN
OPEN
OPEN
CLOSE
OPEN
CLOSE
CLOSE
OPEN
CLOSE
OPEN
CLOSE
CLOSE
NOTE
• If the battery is inserted upside down in the B holder, it might be difficult to remove. If
that happens, take following measures:
(1) Remove the battery cover and turn the projector's upside up.
(2) While lifting the side of the projector closer to the lens, press the metal claw of the
battery holder. The battery will fall out of the holder, so be careful not to lose it.
WARNING
►Always handle the batteries with care and use them only as directed. Battery may
explode if mistreated. Do not recharge, disassemble or dispose of in fire.
And also improper use may result in cracking or leakage, which could result in fire,
injury and/or pollution of the surrounding environment.
• Be sure to use only the batteries specified.
• Make sure the plus and minus terminals are correctly aligned when loading a battery.
• Keep a battery away from children and pets. If swallowed consult a physician
immediately for emergency treatment.
• Do not short circuit or solder a battery.
• Do not allow a battery in a fire or water. Keep batteries in a dark, cool and dry place.
• If you observe battery leakage, wipe out the leakage and then replace a battery. If
the leakage adheres to your body or clothes, rinse well with water immediately.
• Obey the local laws on disposing the battery.
LX400 User Manual - Concise
11
020-000166-02 Rev. 1 (08-2009)
Using the CD manual
The other manuals for this product are written into the included CD-ROM titled “User’
s Manual (detailed)”. Before using the CD-ROM, please read the following to ensure the
proper use.
System requirements
The system for using the CD-ROM requires the following.
Windows®:
OS: Microsoft® Windows® 98, 98SE, Me, 2000/XP, Windows NT®4.0, or later
CPU: Pentium® processor 133MHz / Memory: 32MB or more
®
Macintosh :
OS:Mac OS 10.2 or later
CPU:Power PC® / Memory: 32MB or more
CD-ROM drive: 4x CD-ROM drive
Display:
256 color / 640x480 dots resolution
Applications:
Microsoft Internet Explorer4.0 or later
How to use the CD
1. Insert CD into PC’s CD-ROM drive.
Windows®:
Macintosh®:
In a while, Web browser automatically starts. Start up window comes up.
(1) Double-click on the ”Projectors” icon appeared on the desktop screen.
(2) When “main.html” file is clicked, Web browser will start and Initial
window will appear.
2. Click the model name of your projector first, and then click language you want from the
displayed list. The user’s manual (detailed) will open.
CAUTION
►Only use the CD-ROM in a computer CD drive. The CD-ROM is designed for
PC use only. NEVER INSERT THE CD-ROM INTO A NON-COMPUTER CD
PLAYER! Inserting the CD-ROM into an incompatible CD drive may produce a
loud noise, which in turn MAY RESULT IN EAR AND SPEAKER DAMAGE!
►After using CD-ROM, please put it into CD case and keep it. Please keep
the CD neither in direct sunlight nor in a high temperature and high humidity
environment.
NOTE
• The information in the CD-ROM is subject to change without notice.
• No responsibility is taken for any obstacle and defect to hardware and software of your
PC as a result of the use of the CD-ROM.
• All or Any part of the information in the CD-ROM must not be copied, reproduced or
republished without notice to our company.
LX400
User Manual - Concise
2
020-000166-02 Rev. 1 (08-2009)
Regulatory notices
About Electro-Magnetic Interference
In Canada : This Class B digital apparatus complies with Canadian ICES-003.
In the US and places where the FCC regulations are applicable
Declaration of Conformity
Trade name:
CHRISTIE
Model Number:
LX400
Responsible Party: Christie Digital Systems USA, Inc.
Address:
10550 Camden Drive, Cypress CA 90630 U.S.A.
Telephone Number: +1-800-407-7727
This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and (2)
This device must accept any interference received, including interference that may
cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interface by one or more
of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
- Consult the dealer or an experienced radio/TV technician for help.
INSTRUCTIONS TO USERS:
Some cables have to be used with the core set. Use the accessory cable or a designatedtype cable for the connection. For cables that have a core only at one end, connect the
core to the projector.
CAUTION: Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
About Waste Electrical and Electronic Equipment
The mark is in compliance with the Waste Electrical and Electronic Equipment
Directive 2002/96/EC (WEEE).
The mark indicates the requirement NOT to dispose the equipment including
any spent or discarded batteries or accumulators as unsorted municipal waste,
but use the return and collection systems available.
If the batteries or accumulators included with this equipment, display the
chemical symbol Hg, Cd, or Pb, then it means that the battery has a heavy
metal content of more than 0.0005% Mercury or more than, 0.002% Cadmium,
or more than 0.004% Lead.
LX400 User Manual - Concise
13
020-000166-02 Rev. 1 (08-2009)
Specifications
Item
Product name
Panel size
Liquid
Crystal Drive system
Panel
Pixels
Lens
Lamp
Audio output
Power supply
Power consumption
Temperature range
319
Ports
Specifications
Liquid crystal projector
2.0cm (0.79 type)
TFT active matrix
786,432 pixels (1024 horizontal x 768 vertical)
Zoom lens, F=1.7 ~ 1.9, f=24 ~ 29mm (approx.)
275W UHB
4W x4
AC 100-120V/5.0A, AC220-240V/2.1A
460W
5~35˚C (Operating)
RGB1 ..................................................... D-sub 15 pin mini x 1
RGB2 G/Y, B/CB/PB, R/CR/PR, H, V .............................BNC x 5
S-VIDEO ......................................................mini DIN 4 pin x 1
VIDEO ........................................................................ RCA x 1
Y, CB/PB, CR/PR (component video) ............................ RCA x 3
HDMI ......................................................................... HDMI x1
AUDIO IN1 ....................................................... Stereo mini x 1
AUDIO IN2 ....................................................... Stereo mini x 1
AUDIO IN3 R/L ........................................................... RCA x 1
AUDIO IN4 R/L ........................................................... RCA x 1
RGB OUT ............................................... D-sub 15 pin mini x 1
AUDIO OUT ..................................................... Stereo mini x 1
USB ...................................................................... USB (B) x 1
REMOTE CONTROL ........................................ Stereo mini x1
CONTROL ....................................................... D-sub 9 pin x 1
LAN ............................................................................ RJ45 x 1
418 (W) x 139 (H) x 319 (D) mm (approx.)
154
139
Size
418
[unit: mm]
Weight (mass)
Optional parts
LX400
7.1 kg (approx.)
Lamp: 003--01 (DT00873)
Air filter: 003-002119-01 (MU05661)
*For more information, please consult your dealer.
User Manual - Concise
14
020-000166-02 Rev. 1 (08-2009)
Warranty and after-service
If an abnormal operation (such as smoke, strange odor or excessive sound) should occur,
stop using the projector immediately. Otherwise if a problem occurs with the projector,
first refer to the “Troubleshooting” of the “Operating Guide” in the CD and run through the
suggested checks.
If this does not resolve the problem, please contact your dealer or service company. They
will tell you what warranty condition is applied.
Please check the following web address where you may find the latest information for this
projector.
http://www.christiedigital.com
NOTE
• The information in this manual is subject to change without notice.
• The manufacture assumes no responsibility for any errors that may appear in this
manual.
• The reproduction, transfer or copy of all or any part of this document is not permitted
without express written consent.
Trademark acknowledgment
All the trademarks are the properties of their respective owners.
According to the indication on the official site of each company, we describe as follows.
• Macintosh® and Mac OS® are registered trademark of Apple Inc.
• Pentium® is registered trademark of Intel Corp.
• Microsoft® and Internet Explorer®, Windows®, Windows NT® are registered trademarks
of Microsoft Corporation in the U.S. and/or other countries.
• Adobe® and Acrobat®, Reader® are registered trademarks of Adobe System
Incorporated.
• PowerPC® is a registered trademark of International Business Machines Corporation.
• DVI is a trademark of Digital Display Working Group.
• HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or
registered trademarks of HDMI Licensing LLC.
•
is a trademark of SRS Labs, Inc.
• WOW technology is incorporated under license from SRS Labs, Inc.
LX400
User Manual - Concise
15
020-000166-02 Rev. 1 (08-2009)
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising