Furuno FI504, FI507 Manual

Furuno FI504, FI507 Manual

FI-504 MULTI

FI-507 MULTI XL

Instrument

www.furuno.co.jp

All brand and product names are trademarks, registered trademarks or service marks of their respective holders.

The paper used in this manual is elemental chlorine free.

9-52 Ashihara-cho,

Nishinomiya, 662-8580, JAPAN

Telephone : +81-(0)798-65-2111

Fax : +81-(0)798-65-4200

All rights reserved.

Printed in Japan

Pub. No. OME-72690-D

(DAMI ) FI-504/507

・FURUNO Authorized Distributor/Dealer

A : OCT

.

2007

D : JAN . 26, 2011

*00016733413*

*00016733413*

* 0 0 0 1 6 7 3 3 4 1 3 *

IMPORTANT NOTICES

General

• This manual has been authored with simplified grammar, to meet the needs of international users.

• The operator of this equipment must read and follow the descriptions in this manual. Wrong operation or maintenance can cancel the warranty or cause injury.

• Do not copy any part of this manual without written permission from FURUNO.

• If this manual is lost or worn, contact your dealer about replacement.

• The contents of this manual and equipment specifications can change without notice.

• The example screens (or illustrations) shown in this manual can be different from the screens you see on your display. The screens you see depend on your system configuration and equipment settings.

• Save this manual for future reference.

• Any modification of the equipment (including software) by persons not authorized by FURUNO will cancel the warranty.

• All brand and product names are trademarks, registered trademarks or service marks of their respective holders.

How to discard this product

Discard this product according to local regulations for the disposal of industrial waste. For disposal in the USA, see the homepage of the Electronics Industries Alliance (http://www.eiae.org/) for the correct method of disposal.

How to discard a used battery

Some FURUNO products have a battery(ies). To see if your product has a battery, see the chapter on Maintenance. Follow the instructions below if a battery is used. Tape the + and - terminals of battery before disposal to prevent fire, heat generation caused by short circuit.

In the European Union

The crossed-out trash can symbol indicates that all types of batteries must not be discarded in standard trash, or at a trash site. Take the used batteries to a battery collection site according to your national legislation and the Batteries Directive 2006/66/EU.

Cd

In the USA

The Mobius loop symbol (three chasing arrows) indicates that Ni-Cd and lead-acid rechargeable batteries must be recycled. Take the used batteries to a battery collection site according to local laws.

Ni-Cd Pb

In the other countries

There are no international standards for the battery recycle symbol. The number of symbols can increase when the other countries make their own recycle symbols in the future.

i

ii

SAFETY INSTRUCTIONS

SAFETY INSTRUCTIONS

The operator of this equipment must read these safety instructions before attempting to operate the equipment.

WARNING

CAUTION

Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury.

Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury.

Warning, Caution

Prohibitive Action

Mandatory Action

Safety instructions for the operator

WARNING

Do not open the equipment.

Only qualified personnel should work inside the equipment.

Safety instructions for the installer

WARNING

Turn off the power at the switchboard before beginning the installation.

Turn off the power to prevent electrical shock.

Do not disassemble or modify the equipment.

Fire or electrical shock can result if the equipment is modified.

Do not operate the equipment with wet hands.

Electrical shock can result.

Make sure the installation site is not subject to water spray.

Fire or electrical shock can result if water leaks into the equipment.

Make sure no rain or water splash leaks into the equipment.

Fire or electrical shock can result if water leaks into the equipment.

Immediately turn off the power at the switchboard if water leaks into the equipment.

Continued use of the equipment can cause fire or electrical shock.

Warning Label

A warning label is attached to the equipment. Do not remove the label. If the label is missing or damaged, contact a FURUNO agent or dealer about replacement.

Observe the following compass safe distances to prevent interference to the instruments:

FI-504

FI-507

Standard compass

0.35 m

Steering compass

0.30 m

0.25 m

TABLE OF CONTENTS

FOREWORD .............................................................................................. iv

SYSTEM CONFIGURATION ....................................................................... v

1.OPERATION ............................................................................................. 1

1.1 Operating Controls, Display Layout...................................................................... 1

1.2 Turning the Power On/Off .................................................................................... 2

1.3 Adjusting Brilliance and Contrast ......................................................................... 2

1.4 Selecting a Display............................................................................................... 3

1.5 Selecting Apparent or True Wind Angle, Wind Speed.......................................... 8

1.6 Resetting Counters and Indications ..................................................................... 8

1.7 Alarms .................................................................................................................. 9

1.8 Timers ................................................................................................................ 11

2. MAINTENANCE, TROUBLESHOOTING .............................................. 13

2.1 Preventive Maintenance..................................................................................... 13

2.2 Troubleshooting.................................................................................................. 14

3. INSTALLATION ..................................................................................... 15

3.1 Equipment Lists.................................................................................................. 15

3.2 Mounting............................................................................................................. 16

3.3 Wiring ................................................................................................................. 18

3.4 Setting Up........................................................................................................... 21

SPECIFICATIONS ................................................................................. SP-1

PACKING LIST ........................................................................................ A-1

OUTLINE DRAWINGS............................................................................. D-1

INTERCONNECTION DIAGRAM ............................................................ S-1 iii

FOREWORD

A Word to the Owner of the FI-504, FI-507

Congratulations on your choice of the FURUNO FI-504 Multi/FI-507 Multi

XL displays, members of the FI-50 series of marine instruments. We are confident you will see why the FURUNO name has become synonymous with quality and reliability.

For over 60 years FURUNO Electric Company has enjoyed an enviable reputation for quality marine electronics equipment. This dedication to excellence is furthered by our extensive global network of agents and dealers.

This equipment is designed and constructed to meet the rigorous demands of the marine environment. However, no machine can perform its intended function unless operated and maintained properly. Please carefully read and follow the recommended procedures for operation and maintenance.

Thank you for considering and purchasing FURUNO equipment.

Features

The FI-504 Multi/FI-507 Multi XL displays provide heading, environment, autopilot, engine, depth, speed, and wind information, all on a high quality, backlit LCD. The sturdy weather-proof case is built to stand up to even the harshest of environments.

The main features are

• Eight varieties of displays: heading, environment, autopilot, engine, depth, speed, timer, and wind.

• Four levels of backlighting including off.

• Timers: Stopwatch and count-down

• Depth alarms: Shallow alarm, Deep alarm

• Anchor alarms: Shallow alarm, Deep alarm

• Voltage alarm monitors power source voltage

• Wind alarms: High apparent wind angle, Low apparent wind angle,

Max. true wind speed, Low true wind speed

• Speed indications: Max. STW, Average STW, SOG, Max. SOG, Average SOG, Wind speed, Max. true wind speed

• Log indication from 0 to 99,999 nm

• Resettable trip counter, from 0 to 999 nm

iv

SYSTEM CONFIGURATION

Standalone configuration

CAN bus Device or

NMEA 2000 Sensor

(ex. Smart Sensor)

FI-504

FI-507

12 VDC

: Standard Supply

: Optional Supply

: Local Supply

NOTICE: Turn on the terminal resistor in the instrument when connecting an NMEA 2000 sensor or CAN bus device. For the procedure, see the section on setting up, in the installation chapter.

v

SYSTEM CONFIGURATION

CAN bus network

FI-504 MULTI

FI-507 MULTI XL

FI-5001 or

FI-5001L

WIND

TRANSDUCER

TERMINAL BOX

(where necessary)

FI-501* and/or

FI-502

FI-505

COURSE PILOT

FI-506

RUDDER

30

FI-503

DIGITAL

CAN bus

Device or

NMEA 2000

SENSOR*

* NMEA 2000 SENSORS

- Boat speed

- Depth

- Heading

- Navigation

- Environment

- Autopilot

- Engine

*FI-501 Wi nd Angle

FI-502 Close Hauled Wind Angle

CAN bus

Device or

NMEA 2000

SENSOR*

CAN bus

Device or

NMEA 2000

SENSOR*

JUNCTION BOX

FI-5002

CAN bus

Device or

NMEA 2000

SENSOR*

CAN bus

Device or

NMEA 2000

SENSOR*

12 VDC

(not necessary if powered by CAN bus network)

: Standard Supply

: Optional Supply

: Local Supply

NOTICE: Turn on the terminal resistor in the terminator of the CAN bus network.

vi

1.

OPERATION

Provided applicable sensors are connected, the FI-504/FI-507 provides the following information, all on a backlit LCD:

• Depth

• Speed

• Heading

• Environment data

• Autopilot (rudder)

• Engine

• Wind

• Timers

• Navigation data

1.1

Operating Controls, Display Layout

Mode name

(Ex. SPD=Speed, DPTH=Depth)

SELECT

CLEAR

APP

TRUE

MODE

DISP

FI-504

FI-507

Key name

SELECT/CLEAR • Select menu option.

• Silence alarm.

• Clear data.

APP/TRUE

Function

• Reset counters and indications.

• Increment value.

• Select apaprent or true (wind) alternately.

• Decrement value.

MODE

DISP key

Select a display.

• Turn on power.

• Select a display category.

Note: The example screens shown in this manual are taken from the FI-

504. The screens from the FI-507 may be different.

1

2

1. OPERATION

1.2

Turning the Power On/Off

To power the instrument, press the DISP key. All LCD segments go on and off and then the last-used display appears.

To power off the instrument, press the DISP and MODE keys together

(about 7-10 seconds). The timer appears and counts down from three seconds to one second, and then the power goes off.

POWER POWER POWER

Press DISP and MODE keys together

3

2 1

POWER

OFF

Power OFF sequence

1.3

Adjusting Brilliance and Contrast

1. Press the DISP and MODE keys together. The display for adjustment of brilliance appears, with current brilliance setting flashing.

BRILL

2

Brilliance setting (flashing)

2. Within seven seconds of completing step 1, press the APP/TRUE key to lower the brilliance, or the SELECT/CLEAR key to raise it.

3. Press the DISP and MODE keys together. The display for adjustment of contrast appears, with current contrast setting flashing.

CONT

Contrast setting (flashing)

3

4. Within seven seconds of completing step 3, press the APP/TRUE key to lower the contrast, or the SELECT/CLEAR key to raise it.

5. Press the DISP and MODE keys together to save the settings and restore normal operation.

The brilliance and contrast will be the same on all units which are synchronized. (For how to synchronize units, see page 26.)

DEPTH

Current depth

Shallow alarm

Deep alarm

Shallow anchor alarm

Deep anchor alarm

1. OPERATION

1.4

Selecting a Display

Use the DISP key to select a display category. Select desired display with the MODE key.

SPEED

Boat speed

Maximum STW

Average STW

SOG

Maximum SOG

Average SOG

VMG to windward

Log

Trip

TIMER

Count-up timer

Count-down timer 1

Count-down timer 2

ENGINE

Trip fuel usage

Fuel usage rate

Engine RPM

AUTOPILOT

Rudder angle

ENVIRONMENT

Battery voltage

Minimum battery voltage alarm

Time

Date

Water temperature

Air temperature

Air pressure

Humidity

Wind chill temperature

Dew point

DISP

WIND

Wind speed

Maximum true wind speed

Maximum true wind speed alarm

Low true wind speed alarm

Wind angle

High apparent wind angle alarm

Low apparent wind angle alarm

Beaufort wind speed

Ground wind direction

HEADING

Current heading

Average heading

Heading on next tack

Course over ground

Course made good

Distance made good

NAVIGATION

Bearing to waypoint

Distance to waypoint

Cross track error

Waypoint number/name

Latitude

Longitude

Course over ground

Speed over ground

Satellites tracked

Roll

Pitch

3

1. OPERATION

1.4.1

Display description

Depth category

Display title

Current depth

Shallow alarm

Deep alarm

Shallow anchor alarm

Deep anchor alarm

DPTH

Indication

SHALLOW

DEEP

Function

Current depth, in meters, feet or fathoms.

Set shallow depth alarm. Audio and visual alarms are released when the depth is lower than the threshold value.

Set deep depth alarm. Audio and visual alarms are released when the depth is higher than the threshold value.

SHALLOW Set shallow anchor alarm. Audio and visual alarms are released when the depth is lower than the threshold value.

DEEP

Set deep anchor alarm. Audio and visual alarms are released when the depth is higher than the threshold value.

Speed category

Display title

Boat speed SPD

Indication

Maximum STW

Average STW

SOG

Maximum SOG

Average SOG

MAX SPD

AVG SPD

SOG

MAX SOG

AVG SOG

VMG to windward VMG

Log

Trip

LOG

TRIP

Function

Boat speed, in knots (kt), miles per hour

(MPH) or kilometers per hour (KMH).

Maximum boat speed, in knots (kt), miles per hour (MPH) or kilometers per hour

(KMH).

Average boat speed, in knots (kt), miles per hour (MPH) or kilometers per hour (KMH).

Speed over ground, in knots (kt), miles per hour (MPH) or kilometers per hour (KMH).

Maximum speed over ground, in knots (kt), miles per hour (MPH) or kilometers per hour (KMH).

Average speed over ground, in knots (kt), miles per hour (MPH) or kilometers per hour (KMH).

Velocity made good to windward, in knots

(kt), miles per hour (MPH) or kilometers per hour (KMH).

Log distance (total distance run), in nautical miles, (NM) kilometers (KM) or statute miles (SM).

Trip distance (distance run between two points), in nautical miles (NM), kilometers

(KM) or statute miles (SM).

4

1. OPERATION

Timer category

Display title

Count up timer UP

Indication

Count down timer 1 DOWN 1

Count down timer DOWN 2

Function

Count-up timer.

Count-down timer 1.

Count-down timer 2.

Wind category

Display title

Wind speed

Maximum true wind speed

Maximum true wind speed alarm

Indication

APP (or TRUE)

MAX TRUE

MAX TRUE

Function

Wind speed, in knots or meters/second.

Maximum true wind speed.

Low true wind speed alarm

Wind angle

High apparent wind angle alarm

APP (or TRUE)

APP HI

Low apparent wind angle alarm

Beaufort wind speed

BFT

TRUE LO

APP LO

Ground wind angle GWIND

Set maximum true wind speed alarm. Audio and visual alarms are released when the wind speed goes higher than the threshold value.

Set low true wind speed alarm. Audio and visual alarms are released when the wind speed goes lower than the threshold value.

Apparent (or true) wind angle, in degrees.

Set high apparent wind angle alarm. Audio and visual alarms are released when the wind angle at starboard goes higher than the threshold value.

Set low apparent wind angle alarm. Audio and visual alarms are released when the wind angle at port goes lower than the threshold value.

Beaufort wind speed. Beaufort speeds up to

12 are shown. See the table below for Beaufort no. and wind speed.

Angle of wind over ground, in degrees.

Bearing reference in Magnetic (MAG) or

True (TRUE).

Beaufort no. and wind speed

5

6

3

4

0

1

2

Beaufort no.

0

1-3

4-6

7-10

11-16

17-21

22-27 kt

Wind speed

0-0.2

m/s

0.5-2.0

2.1-3.5

3.6-5.6

5.7-8.6

8.7-11.2

11.3-14.3

10

11

12

7

8

9

Beaufort no.

28-33 kt

34-40

41-47

48-55

56-63

64

Wind speed

m/s

14.4-17.4

17.5-21.0

21.1-24.6

24.7-28.8

28.9-32.6

32.7-32.9

5

1. OPERATION

Heading category

Display title

Current heading HDG

Indication

Average heading AVG HDG

Heading on next tack TACK

Course over ground COG

Course made good CMG

Distance made good DMG

Navigation category

Display title

Bearing to waypoint BTW

Indication

Distance to waypoint DTW

Cross track error XTE

Waypoint number/name WPT

Latitude LAT

Longitude

Course over ground

LON

COG

Speed over ground

Satellites tracked

Roll

Pitch

SOG

GPS SAT

ROLL

PITCH

Function

Heading, in degrees. Bearing reference in Magnetic (MAG) or True (TRUE).

Average heading, in degrees. Bearing reference in Magnetic (MAG) or True

(TRUE).

Heading on next tack, in degrees true

(fixed). Bearing reference in Magnetic

(MAG) or True (TRUE).

Course over ground, in degrees. Bearing reference in Magnetic (MAG) or

True (TRUE).

Course made good, in degrees. Bearing reference in Magnetic (MAG) or True

(TRUE).

Distance made good, in kilometers

(km), nautical miles (nm) or statute miles (sm).

Function

Bearing to waypoint, in degrees.

Bearing reference of Magnetic (MAG) or

True (TRUE)

Distance to waypoint, in kilometers

(KM), nautical miles (NM) or statute miles (SM).

Cross-track error, in kilometers (KM), nautical miles (NM) or statute miles

(SM).

Waypoint number and name are shown.

Position in latitude.

Position in longitude.

Course over ground, in degrees.

Bearing reference in Magnetic (MAG) or

True (TRUE).

Speed over ground, in knots (KT), miles per hour (MPH) or kilometers per hour

(KMH).

GPS satellites tracked.

Ship’s roll, in degrees.

Ship’s pitch, in degrees.

6

1. OPERATION

Environment category

Display title

Battery voltage

Minimum battery voltage alarm

Indication

VOLTS

VOLTS LO

Time

Date

Water temperature

Air temperature

Air pressure

Humidity

Wind chill temperature

-

-

WATER

AIR

PRE

HUMID

CHILL

Function

Battery voltage.

Set low battery voltage alarm.

Audio and visual alarms are released when the battery voltage goes lower than the threshold value.

Current time, in 12-hour or

24-hour format.

Current date.

Water temperature, in

°

C or

°

F.

Air temperature, in

°

C or

°

F.

Air pressure, in Hectopascal.

Relative humidity, in percentage.

Wind chill temperature, in

°

C or

°

F.

Dew point, in

°

C or

°

F.

Dew point DEW

Autopilot category

Display title

Rudder angle RUDDER

Indication Function

Rudder angle, in degrees either

P(ort) or S(tarboard).

Engine category

Display title

Trip fuel used TOTAL

Fuel rate

RTE (L/H)

Indication Function

Total fuel consumption, in liters or gallons.

Amount of fuel consumed in hour, in liters/hour (L/H) or gallons/hour (G/H).

Engine speed per minute.

Engine RPM

RPM

Note: In case of multiple engines, the data of desired engine number

(max. eight, E0-E7) can be selected with the SELECT/CLEAR key.

Scrolling speed and scrolling direction

Display scrolling speed and direction can be changed by the length of key push.

Short push: Scroll in forward order.

Medium push: Go back one display. Several beeps sound and then the previous display appears.

Hold down: Rapid scrolling, in forward direction. Several beeps sound and then speed is changed.

7

1. OPERATION

1.5

Selecting Apparent or True Wind Angle,

Wind Speed

You can show wind angle and wind speed in apparent or true wind. The

apparent wind is the actual flow of air acting upon a sail, or the wind as it appears to the sailor. True wind is the wind seen by a stationary observer in velocity and direction.

WIth a wind angle or wind speed indication displayed, press the APP/

TRUE key to change the wind angle or wind speed to apparent and true alternately. A beep sounds after the change is completed. (Wind angle and wind speed displays are mutually changed.) True wind requires boat speed input. If there is no speed input three dashes appear.

APP KT

5.0

HI

APP

135

HI

APP

TRUE

APP

TRUE

TRUE KT

9.6

HI

Apparent and true wind speeds

TRUE

157

HI

Apparent and true wind angles

1.6

Resetting Counters and Indications

You can reset the following counters and indications:

• Trip

• Course made good

• Distance made good

• Average speed

• Average SOG

• Maximum speed

• Maximum SOG

• Average heading

• Maximum true wind speed

Select the applicable display and press and hold down the SELECT/

CLEAR key. A short beep sounds, the counter or indication flashes twice and then a long beep sounds to indicate that resetting is completed.

8

1. OPERATION

1.7

Alarms

There nine conditions which trigger audio and visual alarms: Shallow alarm, Deep alarm, Shallow anchor alarm, Deep anchor alarm, Max. true wind speed alarm, Low true wind speed alarm, High apparent wind angle alarm, low apparent wind angle alarm, and low battery voltage alarm.

1. Use the DISP and MODE keys to select desired alarm page, referring to the illustration below for alarm location.

Display category

Available alarms

DEPTH

SHALLOW

020

Shallow alarm

DEEP

150

Deep alarm

SHALLOW

5.0

Shallow anchor alarm

DEEP

10.0

Deep anchor alarm

WIND

TRUE KT

MAX

38.9

Max. true wind speed alarm

TRUE KT

LO

9.7

Low true wind speed alarm

APP S* HI

12.2

High apparent wind angle alarm

APP S* LO

5.4

Low apparent wind angle alarm

ENVIRON-

MENT

VOLTS

LO

9.0

Low voltage alarm

*S (Starboard) or P (Port)

.

Alarm description

Alarm Alarms released when;

Shallow alarm

Deep alarm depth is shallower than this threshold.

depth is deeper than this threshold.

Shallow anchor alarm anchor depth is shallower than this threshold.

Deep anchor alarm anchor depth is greater than this threshold.

Max. true wind speed alarm

Low true wind speed alarm

High apparent wind angle alarm

Low apparent wind angle alarm max. true wind speed is greater than this threshold.

true wind speed is lower than this threshold.

apparent wind angle is higher than this threshold.

apparent wind angle is lower than this threshold.

0.0-303 m

Setting range

0.1-304 m depth is shallower than this threshold.

depth is deeper than this threshold.

0.1-999 kts

0-998 kts

S0

°

-S179

° (High)

S180

°

-P1

° (Low)

(S=Starboard, P=Port)

9

1. OPERATION

Alarm description

Alarm

Low battery voltage alarm

Alarms released when;

battery voltage is lower than this threshold.

Setting range

5.0 - 20.0 volts

2. If the selected alarm page shows “Off,” press and hold down the

SELECT/CLEAR key until an alarm setting appears.

3. Press the APP/TRUE and SELECT/CLEAR keys together to enable adjustment. The alarm setting starts flashing.

4. Press the APP/TRUE key to lower the setting; the SELECT/CLEAR key to raise it.

Note: A low alarm cannot be set higher than its affiliated high (max.) alarm.

5. Press the APP/TRUE and SELECT/CLEAR keys together to confirm setting and restore normal operation.

When an alarm is violated, the buzzer sounds and the alarm icon ( ) flashes. You can silence the buzzer with the SELECT/CLEAR key. The icon continues flashing until the offending alarm is disabled.

While the icon is flashing you can switch between alarm display and current display alternately by pressing the DISP and SELECT/CLEAR keys together.

10

1. OPERATION

1.8

Timers

Three timers are provided:

• Count-up timer (stopwatch)

• Count-down timer (two provided)

Time is displayed in seconds or minutes, depending on counter values.

Once you have set a timer, you can leave that page and select any other display. The counter continues to run in the background.

Count-up timer

The count-up timer functions like a stop watch, counting time upward, to

99 hours, 99 minutes and 59 seconds.

Count-down timers

The two count-down timers count down from a time between 15 minutes and one minute. When these timers have counted down to zero, they then start counting up. The timers beep at preset intervals to alert you to specific points in time.

• Two beeps every minute

• Three beeps at the start of the last 30 seconds

• One beep/second for each of the last 10 seconds

• Two-second beep at zero

How to set the timers

1. Press the MODE key to show the desired timer display.

00:00:00.0

UP

Count-up timer

DOWN 1

15.0

Count-down timer 1

DOWN 2

15.0

Count-down timer 2

2. Do one of the following depending on timer type selected:

Count-up timer:

Press the SELECT/CLEAR key to start the timer. A long beep sounds and the timer starts counting upward.

Count-down timer:

To start the timer from the time shown, press the SELECT/CLEAR key. To set a different start time, press the APP/TRUE and SELECT/

CLEAR keys together to enable adjustment. Use the APP/TRUE key to lower the value; SELECT/CLEAR key to raise it. Press the APP/

TRUE and SELECT/CLEAR keys together to confirm setting. Press the SELECT/CLEAR key to start the timer.

11

1. OPERATION

To stop or restart the timer, press the SELECT/CLEAR key momentarily. A short beep sounds when the timer is stopped or restarted.

To stop and reset the timer to start value, press the SELECT/CLEAR key until you hear a long beep. The timer is stopped and reset to start value.

The timer settings are reflected on any timer-equipped instrument in the network which is set up for synchronization.

12

2.

MAINTENANCE,

TROUBLESHOOTING

This chapter provides the information necessary for keeping your equipment in good working order.

WARNING

Do not open the equipment.

Only qualified personnel should work inside the equipment.

2.1

Preventive Maintenance

Following the recommended procedures below will help maintain performance.

Check item

Cabling

Cabinet

Check point Remedy

Check that all cabling is securely fastened and is free or rust and corrosion.

Dust on cabinet

Reconnect if necessary. Replace if damaged.

Remove dust with a soft, lint-free cloth.

NOTICE

Do not apply paint, anti-corrosive sealant or contact spray to coating or plastic parts of the equipment.

Those items contain organic solvents that can damage coating and plastic parts, especially plastic connectors.

13

2. MAINTENANCE, TROUBLESHOOTING

2.2

Troubleshooting

If you feel the equipment is not functioning properly, follow the procedures in the table below to try to restore normal operation. If normal operation cannot be restored, do not attempt to check inside the cabinet.

There are no user-serviceable parts inside.

Troubleshooting

Problem

Display is blank. Panel is not lit.

Possible cause

• Power supply

• Cabling disconnected or damaged.

Remedy

• Check power supply.

• Check cabling.

Power is on but no or some data.

Sensor is turned off.

Cable from sensor is disconnected or damaged.

Inaccurate data • Electromagnetic field generating equipment is in operation.

• Cabling from sensor is damaged.

• Turn on sensor.

• Check cabling.

• Turn off all electromagnetic field generating equipment. Turn them on and off one by one. Check the display. Relocate offending equipment or this instrument as appropriate.

• Check cabling.

• Sensor is improperly aligned

(where applicable).

• Check installation. If installation is proper, an offset may be applied to certain data. For details, see section

1.7.

14

3.

INSTALLATION

NOTICE

Do not apply paint, anti-corrosive sealant or contact spray to coating or plastic parts of the equipment.

Those items contain organic solvents that can damage coating and plastic parts, especially plastic connectors.

3.1

Equipment Lists

Standard supply

(FI-504)

Name

Display Unit

Installation

Materials

Type

FI-504 -

Code No.

CP26-00600 000-011-744

Qty

1

1 set

Remarks

See packing list at end of manual for details.

(FI-507)

Name

Display Unit

Installation

Materials

Optional supply

Type

FI-507 -

Code No.

CP26-00800 000-015-730

Name

Cable Assy.

Type

FI-50-DROP-6M

Code No.

001-105-810-10

FI-50-CHAIN-0.3M

001-105-820-10

FI-50-CHAIN-5M 001-105-840-10

FI-50-CHAIN-1M 000-166-950-11

FI-50-CHAIN-10M 001-105-850-10

FI-50-CHAIN-20M 001-105-860-10

Flush Mount Kit FI-50-FLUSH-KIT 000-010-619

Junction Box

Smart Sensor

FI-507-FLUSH-KIT 000-015-722

FI-5002 000-010-765

DST-800 000-168-850-10

Qty

1

Remarks

1 set See packing list at end of manual for details.

Qty

1

1

1

Remarks

1

1

1

1 set For FI-504

For FI-507

1 set

1

15

3. INSTALLATION

3.2

Mounting

The display unit can be installed two ways: surface mount (fixed at front panel or fixed from rear panel) and flush mount (optional kit required).

This section covers surface mounting. For flush mounting, see the flush mounting instructions, issued separately.

Surface mount 1: Fix instrument from front panel

1. Using the applicable template at the back of this manual, open a mounting hole in the installation site.

2. Detach the front panel together with the keypad assy. Attach sponge

(supplied) to rear of display unit.

3. Set the display unit to the mounting hole, and fix it with four self-tapping screws (3×20, supplied).

4. Attach the front panel and keypad assy. to the display unit.

Keypad Assy.

Sponge

Mounting

Hole

Front Panel

(ex. FI-504)

Self-tapping screw (3x20)

16

3. INSTALLATION

Surface mount 2: Fix instrument from rear panel

1. Using the applicable template at the back of this manual, open a mounting hole in the installation site.

2. Insert studs (M3×40, 2 pcs. (FI-504) or 4 pcs. (FI-507), supplied) in the holes shown below. (Use only the studs supplied.)

Insert stud here.

(FI-504)

(FI-507)

Display unit, rear view

3. Set the display unit to the mounting hole, inserting studs through respective holes. Fix the display unit with spring washers, flat washers and wing nuts (M3, supplied).

Flat Washer and

Spring Washer (M3)

Mounting

Hole

(ex. FI-504)

Stud (M3x40)

Wing Nut (M3)

17

3. INSTALLATION

3.3

Wiring

For the service technician detailed information about CAN bus wiring is on the FURUNO Tech-net. See “Furuno CAN bus Network Design

Guide” (TIE-00170-*).

3.3.1

Standalone configuration

For standalone configuration the junction box is not necessary; connect the instrument directly to the power supply.

CAN bus Device or

NMEA 2000 Sensor

CAN bus drop cable

FI-50-DROP-6M

Cable (6 m)

Black

+

Red

12 VDC

Display Unit

FI-504/507

(507 not shown)

3.3.2

Multi-instrument configuration

FI-50-CHAIN

(0.3 m: Std, 1/5/10/20 m: Option)

DISP. UNIT

FI-501/502/FI-503/FI-505/FI-506

(Instruments can be connected in any order.)

DISP. UNIT

FI-504/507

(507 not shown)

Instruments chained as above

Instruments chained as above

Power Cable (2 m)

FI-50-DROP-6M Cable

(6 m, standard supply)

JUNCTION BOX

FI-5002

(optional supply)

Black

– +

Red

CAN bus

Backbone Cable

(local supply)

FI-50X FI-50X FI-50X

Instruments chained as above

Instruments chained as above

Instruments chained as above

JUNCTION BOX FI-5002

NOTE: The total length of drop cables and backbone cables must be within 80 m.

18

3. INSTALLATION

Junction box (option)

The junction box is required when connecting CAN bus network. This section covers wiring of the junction box. For how to mount the junction box, see its installation instructions, issued separately.

CN1

12VDC

CN3

DROP

CN4

DROP

CN5

DROP

CN2

BACKBONE

12 VDC

FI-501/502/503/504/505/506/507

CAN bus

Device

Fix cable with cable tie (supplied).

CH3 DROP - CH5 DROP and BACKBONE are socket-and-plug-type terminal blocks. Detach plug to connect wiring to it, by rocking it back and forth with your fingers. Remove approx. 6 mm of the sheath from the end of wires and twist wires. Loosen fixing screw in the plug, insert wire into hole and tighten fixing screw. Set plug to socket.

Drain wire

White

Red

Blue

Black

Sheath

6mm

How to fabricate cable

Fixing screw

Hole for wire

Wire

Twist

How to insert wire

19

3. INSTALLATION

Terminal resistor

The illustration below show various system configurations and what units to activate the terminal resistor.

Smart sensor+FI-50x

Smart

Sensor

FI-50x

Multiple FI-50 series instruments, FI-5002, drop cabling

FI-50x FI-50x FI-50x

Drop cable

FI-5002

FI-50x

Multiple FI-50 series instruments, FI-5002

FI-50x FI-50x FI-50x FI-50x

FI-5002

Multiple FI-50 series instruments, multiple FI-5002

FI-50x FI-50x FI-50x FI-50x FI-50x FI-50x

FI-5002 FI-5002 FI-5002

Multiple FI-50 series instruments, FI-5002, smart sensor

Smart

Sensor

FI-50x FI-50x FI-50x

FI-5002

Multiple FI-50 series instruments, FI-5002, heading sensor, smart sensor

NMEA 2000

Sensor

Heading

Sensor

(ex. SC-30)

Smart

Sensor

FI-50x FI-50x

Terminator

FI-5002

T-connector

T-connector

T-connector

Terminator

Multiple FI-50 series instruments, FI-5002, NMEA 2000, CAN bus sensors

CAN bus Device or

NMEA 2000 Sensor

CAN bus Device or

NMEA 2000 Sensor

FI-50x FI-50x

Terminator

FI-5002

T-connector

= Terminal resistor ON

T-connector

20

3. INSTALLATION

Turn on the terminal resistor in the junction box when the FURUNO CAN bus and/or NMEA 2000 sensor(s) connected to it do not have a terminal resistor.

Terminal Resistor

OFF:

ON:

For how to turn on the terminal resistor in a FI-50 series instrument, see paragraph 3.4.2 “Setup2 menu”.

3.4

Setting Up

Your instrument is pre-programmed with factory default settings, which may or may not be suited to your vessel. Therefore, it is necessary to initialize the instrument for use with your vessel. This should be done immediately after completion of the installation.

Two sets of setup menus are provided: setup1 and setup2. The setup1 menu provides system parameters and the setup2 menu has user settings.

3.4.1

Setup1 menu

The setup1 menu contains system parameters which optimize the instrument for use on your vessel. Follow the procedure below to access and set parameters.

1. Press the APP/TRUE and SELECT/CLEAR keys momentarily to enable the setup1 menu. The Depth unit selection screen appears, with the depth unit flashing. (See the illustration on the next page.)

2. Use the DISP key to select a menu item. Each press of the key changes the menu item in the sequence shown in the illustration on the next page.

21

.

3. INSTALLATION

DPTH M

CAL

Depth unit

DPTH M

CAL

0.0

Depth offset

SHWLOCK

CAL

DPT RES

CAL

Off

Shallow alarm lock

3

Depth response

SPD KT

CAL

Speed unit

SPD

CAL

SPD --- --- ---

CAL

0.01

Speed unit resolution

1.00

Speed offset

LOG NM

CAL

LOG unit

SPD RES

CAL

SOG RES

CAL

0

Speed response

0

SOG response

VMG RES

CAL

3

VMG response

TIMER

CAL

WIND

CAL

On

Audio alarm enable/disable

F

Wind data selection

WIND KT

CAL

WINDADJ

CAL

Wind unit

1.0

Wind speed adjustment

ANGLE S

CAL

WSPDRES

CAL

0

Wind angle offset

HDG MAG

CAL

HDGLOCK

CAL

HDG RES

CAL

3

LOC 0

Wind speed

Heading reference Heading response response

TIME HR

CAL

12

Time format

--- ---:--- --TEMP C

CAL

CAL

W TEMP

CAL

0

Local time Water temp. unit

0.0

Water temp. offset

FUEL L

CAL

Fuel unit

3. Use the APP/TRUE or SELECT/CLEAR key to set value or select option.

VMG key: Decrement value

SELECT/CLEAR key: Increment value or select option.

4. To continue, press the DISP key to select another menu item.

5. To save settings and restore normal operation, press the APP/TRUE and SELECT/CLEAR keys together.

22

Display

DPTH M

CAL

3. INSTALLATION

Setup1 menu items

Function

Select depth unit.

Setting range or options

M (Meter),

FT (Feet)

Default setting

M

DPTH M

CAL

0.0

SHWLOCK

CAL

OFF

DPT RES

CAL

3

SPD KT

CAL

Set depth offset.

-99 - +99

Lock/unlock shallow alarm setting. ON, OFF

Set depth response. The lower the setting the faster the response to change in depth.

0 - 12

Select speed unit.

0.0

OFF

3

KT (Knot),

MPH (Miles/Hour),

KMH (Kilometers/Hour)

KT

SPD

CAL

0.01

SPD --- --- ---

CAL

1.00

LOG NM

CAL

Select speed resolution. Select number of places to show after decimal point.

0.01, 0.1

Set speed adjustment.

(STW only)

Select log unit.

0.30 - 2.50

NM (Nautical Mile),

SM (Statute Mile),

KM (Kilometer)

0.01

1.00

NM

23

3. INSTALLATION

Display

SPD RES

CAL

0

SOG RES

CAL

0

VMG RES

CAL

3

TIMER

CAL

On

WIND

CAL

F

WIND KT

CAL

Setup1 menu items

Function

Set speed response. The lower the setting the faster the response to change in speed.

Setting range or options

0 - 12

Set SOG response. The lower the setting the faster the response to change in speed over ground.

0 - 12

Set VMG response. The lower the setting the faster the response to change in velocity made good.

0 - 12

Enable/disable the timer alarm’s audio alarm.

ON, OFF

Select source of wind data. Select

“r” for second unit.

F: For FI-5001 (Furuno

Sensor), r: repeater

F

Select wind unit.

KT (Knot),

M/S (Meters/Second)

0

Default setting

0

3

ON

KT

1.0

24

WINDADJ

CAL

1.0

ANGLE S

CAL

0

WSPDRES

CAL

3

Set wind speed adjustment.

Set wind angle offset.

0.3 - 2.5

S 0

°

- 180

°

P 1

°

- 179

°

Set wind speed response.

The higher the setting the faster the response to change in wind speed.

0 - 12

0

3

Display

HDG MAG

CAL

3. INSTALLATION

Setup1 menu items

Function

Setting range or options

Select true or magnetic bearing.

MAG (Magnetic),

TRU (True

Default setting

MAG

LOC

HDGLOCK

CAL

LOC

HDG RES

CAL

0

TIME HR

CAL

12

--- ---:--- ---

CAL

0

TEMP C

CAL

Select heading type to display when activating locked heading.

LOC (Locked),

CUr (Current)

Set heading response. The lower the setting the faster the response to change in heading.

0 - 12

Select time format.

12, 24 (hour)

Use local time. Enter time difference between local time and GMT to use local time.

-12 - +12

Select water temperature unit.

°

C,

°

F

0

12

0

°

C

W TEMP

CAL

0.0

FUEL L

CAL

Set water temperature offset.

Select fuel unit.

-99 - +99

L (Liter),

G (Gallon)

0

L

25

3. INSTALLATION

3.4.2

Setup2 menu

The setup 2 menu contains user settings which once preset do not require frequent adjustment.

1. Press and hold down the APP/TRUE and SELECT/CLEAR keys together (about 5-6 seconds) to enable the user settings menu. The software version of CPU1 appears. (See the illustration below.)

2. Press the DISP key to choose menu item. Each press of the key changes the menu item in the sequence shown below.

*XXxx=program and program ver. nos.

Xxxxx*

Program ver.

Xxxxx*

Program ver.

KEYBEEP

CAL

ON

Key no. (CPU1) no. (CPU2) beep

A BRILL

CAL

ON

Auto brilliance

ALT

CAL

OFF

Alternating displays

SETUP

CAL

ON

Setup 1 menu

rES

CAL

OFF

Terminal resistor

SYNCHRO

CAL

ON

Synchronization

DEPTH

CAL

ON

Depth displays

TIMER

CAL

ON

Timer displays

WIND

CAL

ON

Wind displays

HEADING

CAL

ON

Heading displays

NAVI

CAL

ON

Nav displays

SPEED

CAL

ON

Speed displays

ENVIRO

CAL

ON

Environment displays

A PILOT

CAL

ON

Autopilot displays

ENGINE

CAL

ON

Engine displays

DEMO

CAL

OFF

Demo mode

RESET

CAL

OFF

Restore factory defaults

3. Use the SELECT/CLEAR key to select setting.

4. To continue, press the DISP key to select another item.

5. To save settings and restore normal operation, press the APP/TRUE and SELECT/CLEAR keys together.

26

3. INSTALLATION

KEYBEEP

CAL

ON

A BRILL

CAL

ON

ALT

CAL

OFF

Display

Xxxxx

Xxxxx

Setup2 menu items

Function

Setting range or options

Software version of CPU1.

X=program no. and xxxx=program version no.

Software version of CPU2.

X=program no. and xxxx=program version no.

Turn key beep on/off.

-

-

ON, OFF

Auto brilliance on/off.

ON, OFF

SETUP

CAL

ON rES

CAL

OFF

SYNCHRO

CAL

ON

DEPTH

CAL

ON

SPEED

CAL

ON

Enable/disable alternating displays.

Enable/disable access to the setup1 menu.

OFF

1: Depth/boat spd

2: Boat spd/water temp.

3: Depth/water temp.

4: Depth/boat spd/water temp.

5: Roll/pitch

6: Latitude/Longitude

ON, OFF

OFF

ON

OFF Turn the terminal resistor on/ off.

ON, OFF

Turn on/off synchronization of

FI-50 series instruments.

ON:

Synchronize FI-50

instruments having this

setting.

OFF:

Turn off synchronization.

A:

Synchronize FI-50 instru-

ments having this setting.

b:

Synchronize FI-50 instru-

ments having this setting.

Turn depth displays on/off.

ON, OFF

ON

ON

Turn speed displays on/off.

ON, OFF

-

-

Default setting

ON

ON

ON

27

3. INSTALLATION

Display

TIMER

CAL

ON

WIND

CAL

ON

HEADING

CAL

ON

NAVI

CAL

ON

ENVIRO

CAL

ON

A PILOT

CAL

ON

ENGINE

CAL

ON

DEMO

CAL

OFF

RESET

CAL

OFF

Setup2 menu items

Function

Turn timer displays on/off.

Setting range or options

ON, OFF

Turn wind displays on/off.

ON, OFF

Turn heading displays on/off. ON, OFF

Turn navigation displays on/off.

ON, OFF

Turn environmental displays on/off.

ON, OFF

Turn autopilot displays on/off. ON, OFF

Turn engine displays on/off.

ON, OFF

Demo mode. To enable, press the SELECT/CLEAR key. Depth is shown.

To disable and return to this menu, press and hold down the SELECT/CLEAR key.

Restore factory defaults.

To restore factory defaults, press and hold down the

SELECT/CLEAR key to show ON. Press the key again. A beep sounds upon completion.

ON, OFF

ON, OFF OFF

Default setting

ON

ON

ON

ON

ON

ON

ON

OFF

28

FI-504 MULTI

SPECIFICATIONS OF

FI-504 MULTI

1 GENERAL

1.1 Indication system Segment LCD

1.2 Brilliance

1.3 Contrast

1.4 Display Contents Depth, speed, wind speed, wind angle, timer, environmental information (water temperature, air temperature, air pressure, dewpoint, wind chill temperature), rudder angle

CAN bus, 2 ports

Surface or flush mount

1.5 Number of Port

1.6 Mount Method

2 JUNCTION BOX (OPTION)

2.1 Number of Port

2.2 Circuit Protection

CAN bus Drop: 6 ports,

CAN bus Backbone: 2 ports

Reverse, short, over current

3 POWER SUPPLY AND POWER CONSUMPTION

3.1 Display Unit 12 VDC, less than 0.1 A

12 VDC, less than 1 A, max. 2A connectable

4.1 Useable Temperature Range -15°C - +55°C

4.2 Relative Humidity Less than 95% (+40°C)

4.3 Waterproofing

4.4 Vibration

IP56

IPX0

- 2 Hz-5 Hz and up to 13.2 Hz with an excursion of ±1 mm ±10% (7 m/s

2 maximum acceleration at 13.2 Hz);

- above 13.2 Hz and up to 100 Hz with a constant maximum acceleration of 7 m/s

2

N2.5

N2.5

SP-1

E7269S01A1

FI-507 MULTI XL

SPECIFICATIONS OF

FI-507 MULTI XL

1 GENERAL

1.1 Indication system

1.2 Brilliance

1.3 Contrast

1.4 Display contents

Segment LCD

Depth, Ship’s speed, Wind speed/angle, Date, Time, Bearing

1.5 Number of port

Rudder angle, Engine information

*2

CAN bus: 2 port

1.6 Mount method Surface or flush mount

*1) Battery voltage, date, time, water temperature, air temperature, air pressure, humidity, wind chill temperature and dew point

*2) Fuel consumption, fuel efficiency and engine speed

2.1 Number of port

2.2 Circuit protection

3.1 Main unit

3.2 Junction box

CAN bus drop: 6, CAN bus backbone: 2

Reverse, short, over current

12 VDC: 0.1 A

12 VDC: 1 A

4.1 Ambient temperature -15°C to +55°C

4.2 Relative humidity 95% at 40°C

4.3 Degree of protection

Main unit

Junction box

4.4 Vibration

IP56

IPX0

- 2 Hz-5 Hz and up to 13.2 Hz with an excursion of

±1 mm ±10% (7 m/s

2

maximum acceleration at 13.2

Hz);

- above 13.2 Hz and up to 100 Hz with a constant maximum acceleration of 7 m/s

2

N2.5

N2.5

SP - 2

E7277S01A

A-1

A-2

D-1

D-2

D-3

D-4

D-5

*1) (1/5/10/20m

FI-50-CHAIN,0.3m,φ6

*1) (1/5/10/20m

FI-50-CHAIN,0.3m,φ6

S-1

タッピンネジ用穴(4ヵ所)

For tapping screws (4 pcs.)

寸切りボルト用穴(2ヵ所)

For bolts (2 pcs.)

FI-50シリーズ 表示部 フラッシュマウント用型紙

FI-50 series Display unit Flush Mount Template

FI-507

サーフェイスマウント用型紙

FI-507 Surface Mount Template

Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project