Comp-S (2015)
Installation Instructions
1.
Make sure the bike is completely cool before starting the
installation and secure on a service lift.
2.
Loosen OEM joint clamp and heat shield clamp.
Care & Cleaning
Care & Cleaning
Keep system free of dirt and moisture. Store in a cool, dry place. Make sure vehicle is
completely cool before maintenance.
Stainless Header System: Polished stainless steel pipes will turn a light golden hue
after a few heat cycles, this is a normal characteristic of high quality stainless steel.
Clean using a mild water based spray cleaner. Always apply cleaner or polish with a
soft, clean cloth.
Harley Davidson
Titanium Header System: Polished titanium pipes will experience color shift ranging
from deep blue/purple through amber after a few heat cycles. This is a normal
characteristic of high quality titanium. Clean using a mild water based spray cleaner.
Always apply cleaner or polish with a soft, clean cloth.
STREET 500/750
Slip-On Exhaust System
Part # 005-3970499-B
3.
Remove two rear mount bolts. These will not be used with
the TBR mufflers.
Polished Aluminum Canisters: Use an aluminum or mag wheel polish to restore the
bright finish to factory spec.
Brushed Aluminum Canisters: Clean using a mild water based spray cleaner. Always
apply cleaner or polish with a soft, clean cloth.
Carbon Fiber Canisters: Clean using a mild water based spray cleaner. Always apply
cleaner or polish with a soft, clean cloth. Always make sure the fiberglass packing inside
is in good condition and not burned out, as exhaust heat inside an empty canister will
deteriorate the carbon fiber sleeve.
TBR sells repack kits (Road - #005-10038, Offroad - #005-10038MX) that include
everything you need to easily do it yourself.
4.
Remove OEM muffler.
5.
Install TBR slip-on onto OEM mid-pipe.
6.
Install two rear 5/16” mounting bolts and tighten snug.
Titanium Mufflers: For cleaning use a mild water based spray cleaner. Always apply
cleaner or polish with a soft, clean cloth. Always make sure the fiberglass packing inside
is in good condition and not burned out, as exhaust heat inside an empty canister will
deteriorate the carbon fiber sleeve.
TBR sells repack kits (Road - #005-10038, Offroad - #005-10038MX) that include
everything you need to easily do it yourself.
Repack all road canisters every 3,000 miles. Part #005-10038
Repack all offroad canisters after every 10 hours of use. Part #005-10038MX
NEVER dyno test your bike with carbon fiber or titanium canisters installed - the
intense heat and lack of cooling air can quickly burn through the canister material. Two
Brothers Racing does not provide a warranty for burned canisters.
Parts List
Qty. Description
Part Number
2
2-005-FB51634
Flange Bolt
7.
Tighten joint clamp and heat shield clamp.
8.
Double check all your work.
9.
Before you run the bike, clean off all fingerprints and
dirt, as any oily residue will etch the metal and become
somewhat permanent when the system gets hot. Run
the bike and enjoy. It is normal for some white smoke to
appear the first time you start the bike. This is packing/
manufacturing oil from inside the pipe burning off. Check
for gaps or leaks. If you find a leak, a little high temperature
silicon sealant should fix it. After 50 to 100 miles, recheck
all fasteners for tightness.
IMPORTANT - PLEASE READ CAREFULLY
We recommend that this performance part be installed
by a qualified motorcycle technician. If you have any
doubts as to your ability to install this performance part,
please consult with your local motorcycle dealer. Read all
instructions first before starting installation. Make sure
the motorcycle and exhaust system are completely cool
before starting the installation. Also, make sure the bike
is secure on a centerstand or ideally a service lift during
installation. Be sure to save all stock components for
possible use later.
Warranty
Two Brothers Racing products are intended for closed course competition purposes only,
and therefore are sold “as is” without warranty. Two Brothers Racing specifically disclaims
any warranties of merchantability or fitness for a particular purpose and disclaims all
responsibility for consequential and incidental damages or any other losses arising from
the use of these products or parts.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement