Bose Wave radio Series I Specifications

Bose Wave radio Series I Specifications
The Bose® Wave® Radio/CD
Owner’s Guide
Safety Information
English
WARNING: To reduce the risk of fire or electric shock, do not expose the Wave® radio/CD to
rain or moisture. The apparatus shall not be exposed to dripping or splashing, and objects
filled with liquids, such as vases, shall not be placed on the apparatus.
As with any electronic product, use care not to spill
liquids into any part of the system. Liquids can cause
a failure and/or a fire hazard.
AVIS
CAUTION
AVIS
RISK OF ELECTRICAL SHOCK
DO NOT OPEN
RISQUE DE CHOC ÉLECTRIQUE
NE PAS OUVRIR
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK).
NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED PERSONNEL.
AFIN DE PRÉVENIR UN CHOC ÉLECTRIQUE NE PAS ENLEVER
LE COUVERCLE ARRIÈRE. IL NE SE TROUVE À L’INTÉRIEUR
AUCUNE PIÈCE POUVANT ÊTRE RÉPARÉE PAR
L’USAGER. S’ADRESSER À UN RÉPARATEUR COMPÉTENT.
These CAUTION marks are located on the bottom and rear of your Wave® radio/CD :
The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert
the user to the presence of uninsulated dangerous voltage within the system enclosure that
may be of sufficient magnitude to constitute a risk of electric shock.
The exclamation point within an equilateral triangle, as marked on the system, is intended to
alert the user to the presence of important operating and maintenance instructions in this
owner’s guide.
CAUTION: To prevent electric shock, match wide blade of plug to wide slot, insert fully.
Class 1 laser product
CLASS 1
KLASSE 1
LUOKAN 1
KLASS 1
LASER
LASER
LASER
LASER
PRODUCT
PRODUKT
LAITE
APPARAT
This CD player is classified as a CLASS 1 LASER PRODUCT according to
EN 60825-1:1994 + A11. The CLASS 1 LASER PRODUCT label is located
on the back of the system.
CAUTION: Use of controls or adjustments or performance of procedures other than those
specified herein may result in hazardous radiation exposure. The compact disc player
should not be adjusted or repaired by anyone except properly qualified service personnel.
WARNING: Keep the remote control battery away from children. It may cause a fire or
chemical burn if mishandled. Do not recharge, disassemble, heat above 100˚C (212˚F), or
incinerate. Dispose of used battery promptly. Replace only with a battery of the correct type
and model number.
WARNING: No naked flame sources, such as lighted candles, should be placed on the
apparatus.
Batteries
Please dispose of used batteries properly, following any local regulations. Do not incinerate.
Please read this owner’s guide
Please take the time to follow this owner’s guide carefully. It will help you set up and operate
your Wave® radio/CD properly, and enjoy all of its advanced features. Save your owner’s
guide for future reference.
©1994-2003 Bose Corporation. No part of this work may be reproduced, modified, distributed or
otherwise used without prior written permission. All trademarks referenced herein are property of
Bose Corporation. The Wave® radio/CD design is a registered trademark of Bose Corporation.
2
Important Safety Instructions
14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus
has been damaged in any way: such as powersupply cord or plug is damaged; liquid has
been spilled or objects have fallen into the
apparatus; the apparatus has been exposed to
rain or moisture, does not operate normally, or
has been dropped – Do not attempt to service this
product yourself. Opening or removing covers may
expose you to dangerous voltages or other hazards.
Please call Bose to be referred to an authorized
service center near you.
15. To prevent risk of fire or electric shock, avoid
overloading wall outlets, extension cords, or
integral convenience receptacles.
16. Do not let objects or liquids enter the product –
as they may touch dangerous voltage points or
short-out parts that could result in a fire or electric
shock.
17. See product enclosure for safety related
markings.
English
1. Read these instructions – for all components
before using this product.
2. Keep these instructions – for future reference.
3. Heed all warnings – on the product and in the
owner’s guide.
4. Follow all instructions.
5. Do not use this apparatus near water or
moisture – Do not use this product near a
bathtub, washbowl, kitchen sink, laundry tub, in a
wet basement, near a swimming pool, or anywhere else that water or moisture are present.
6. Clean only with a dry cloth – and as directed
by Bose Corporation. Unplug this product from
the wall outlet before cleaning.
7. Do not block any ventilation openings.
Install in accordance with the
manufacturer’s instructions – To ensure
reliable operation of the product and to protect it
from overheating, put the product in a position
and location that will not interfere with its proper
ventilation. For example, do not place the product
on a bed, sofa, or similar surface that may block
the ventilation openings. Do not put it in a built-in
system, such as a bookcase or a cabinet that may
keep air from flowing through its ventilation
openings.
8. Do not install near any heat sources, such
as radiators, heat registers, stoves or other
apparatus (including amplifiers) that produce heat.
9. Do not defeat the safety purpose of the
polarized or grounding-type plug. A polarized plug has two blades with one wider
than the other. A grounding-type plug has
two blades and a third grounding prong. The
wider blade or third prong are provided for
your safety. If the provided plug does not fit
in your outlet, consult an electrician for
replacement of the obsolete outlet.
10. Protect the power cord from being walked
on or pinched, particularly at plugs, convenience receptacles, and the point where
they exit from the apparatus.
11. Only use attachments/accessories specified by the manufacturer.
12. Use only with the cart, stand, tripod,
bracket or table specified by the
manufacturer or sold with the
apparatus. When a cart is used,
use caution when moving the
cart/apparatus combination to
avoid injury from tip-over.
13. Unplug this apparatus during lightning
storms or when unused for long periods of
time – to prevent damage to this product.
Information about products that
generate electrical noise
This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to
Part 15 of the FCC rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, this is no guarantee that interference
will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television
reception, which can be determined by turning the
equipment off and on, you are encouraged to try to
correct the interference by one or more of the following
measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and
receiver.
• Connect the equipment to an outlet on a different
circuit than the one to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Note: Unauthorized modification of the receiver or radio
remote control could void the user’s authority to operate
this equipment.
This product complies with the Canadian ICES-003 Class
B specifications.
2a
3
English
Important Safety Instructions
18. Use proper power sources – Plug the product
into a proper power source, as described in the
operating instructions or as marked on the
product.
19. Avoid power lines – Use extreme care when
installing an outside antenna system to keep
from touching power lines or circuits, as contact
with them may be fatal. Do not install external
antennas near overhead power lines or other
electric light or power circuits, nor where an
antenna can fall into such circuits or power lines.
20. Ground all outdoor antennas – If an external
antenna or cable system is connected to this
product, be sure the antenna or cable system is
grounded. This will provide some protection
against voltage surges and built-up static
charges.
Section 810 of the National Electrical Code ANSI/NFPA
No. 70 provides informaiton with respect to proper
grounding of the mast and supporting structure,
grounding of the lead-in wire to an antenna discharge
unit, size of grounding conductors, location of antennadischarge unit, connection to grounding electrodes, and
requirements for the ground electrode. Refer to the
antenna grounding illustration on this page.
2b
4
Antenna grounding
Example of antenna grounding as per National Electrical Code,
ANSI/NFPA 70.
Antenna lead in wire
Ground clamp
Antenna discharge unit
(NEC Section 810-20)
Grounding conductors
Electric service
equipment
(NEC Section 810-21)
Ground clamps
Power service grounding
electrode system
(NEC ART 250, Part H)
Note to CATV system installer
This reminder is provided to call the CATV system installer’s
attention to Article 820-40 of the NEC (of USA) that provides
guidelines for proper grounding. In particular, it specifies that the
cable ground shall be connected to the grounding system of the
building, as close to the point of cable entry as is practical.
Contents
Where to find…
English
Deutsch
Setting Up
Before you begin ........................................................................................................... 4
Unpacking the carton ................................................................................................... 5
Selecting a location for your Wave® radio/CD .............................................................. 5
Installing the battery ..................................................................................................... 6
Connecting the power cord .......................................................................................... 7
Connecting the FM antenna ......................................................................................... 7
Connecting the coaxial cable ....................................................................................... 7
Installing the remote control battery ............................................................................. 8
Connecting other components as an option .............................................................. 10
Operating Your Wave® radio/CD
Using the remote control ............................................................................................ 12
Using the Wave® radio/CD control panel .................................................................... 13
Reading the Wave® radio/CD display .......................................................................... 14
Setting the time ........................................................................................................... 15
Customizing the display .............................................................................................. 15
Controlling the system ................................................................................................ 16
Using the radio ............................................................................................................ 17
Reading the radio display ........................................................................................... 17
Using the CD player .................................................................................................... 18
Reading the CD display .............................................................................................. 19
Setting the alarms ....................................................................................................... 20
Reading the alarm setup displays ............................................................................... 20
Using the alarms ......................................................................................................... 21
Maintaining Your Wave® radio/CD
Taking care of your Wave® radio/CD .......................................................................... 22
Technical information .................................................................................................. 22
Troubleshooting .......................................................................................................... 23
Customer service ........................................................................................................ 23
Limited warranty ......................................................................................................... 24
Quick Reference to Special Functions ............................................................................. 25
Index ................................................................................................................................. 26
Bose Corporation ..................................................................................... inside back cover
Français
Nederlands
For your records
The serial number is located on the bottom of your system.
Wave® radio/CD serial number: ___________________________________________________
Purchase date: _________________________________________________________________
We suggest you keep your sales receipt and warranty together with this owner’s guide.
3
Setting Up
English
Before you begin
Thank you for purchasing the Bose® Wave® radio/CD.
Fourteen years of research by Bose Corporation bring you the benefits of award-winning
patented acoustic waveguide speaker technology. Using this technology, a tube efficiently
transfers energy from a small loudspeaker to the outside air over a whole range of bass
notes. And, by folding long waveguides into intricate patterns, they fit into products small
enough to be placed comfortably in your home. There is a 27-inch (68-cm) long waveguide
inside the Wave® radio/CD’s compact enclosure, enabling this tabletop system to produce
room-filling sound with full, rich bass.
®
Your Wave® radio/CD includes:
• Integrated system design for high acoustic quality requiring no complex adjustments
• A high performance stereo tuner with 6 AM and 6 FM station presets
• A CD player including skip, scan, random, repeat, and programming features
• Two independent alarms, with battery backup power to save the settings for wakeup
during a power loss
• A credit card-sized remote control
• Inputs for an additional sound source, such as a TV, VCR, computer, or tape player
To discover how easy it is to use your new Wave® radio/CD, follow the steps on the Quick
Set-up Guide and play the demonstration CD. Like most functions, it can be done with the
press of a single button. Some special functions are available by pressing button combinations (for details, see page 25).
To fully appreciate all of these features, please take the time to follow this owner’s guide
carefully. It helps you set up and operate your system, and enjoy its high-fidelity sound.
4
Setting Up
Unpacking the carton
English
Carefully unpack your system. Save all packing materials for possible future use. The original
packing materials provide the safest way to transport your Wave® radio/CD. If any part of the
product appears damaged, do not attempt to use it. Notify Bose® Product Support immediately (see phone numbers on the inside back cover).
Check to be sure your Wave® radio/CD contains the parts identified in Figure 1.
Figure 1
What comes with your
Wave® radio/CD
®
Remote control
Wave® radio/CD
9V battery
Demonstration CD
FM Antenna
Coaxial cable
Selecting a location for your Wave radio/CD
®
Please keep these guidelines in mind when selecting a location for your system:
• Place the Wave® radio/CD on a table or other flat surface.
• Do not place it on a metal surface or table that could interfere with AM reception.
• Do not place it on a heat-sensitive surface. Like all electrical equipment, it generates some
heat.
• Do not use the system in a damp location. It is important to prevent moisture from getting
into the unit.
• Keep it at least 12 inches (30 cm) from a television, computer, or other monitor to prevent
picture quality interference.
• Locate it within 2 feet of a wall for the best bass performance.
• Place it across the room from where you will be listening to enjoy maximum performance
from the Wave® radio/CD.
Feel free to place and position it where you find the sound most pleasing.
5
Setting Up
English
Installing the battery
The 9-volt battery maintains clock and alarm settings and operates the Wave® radio/CD’s
backup alarm system for up to 24 hours, during a power loss or while the system is temporarily unplugged. Operating without this battery leaves the memory unprotected, but will not
harm the product.
Use a standard 9V battery (IEC 6F22 in Europe), available at most retail stores. Use an
alkaline battery for longer backup time.
Note: The battery does not provide power for Wave® radio/CD operation or for the display.
CAUTION: Do not remove the tape from the top front of the system. It prevents the CD door
from opening accidentally when you turn the system over.
1. Carefully turn your system upside down.
2. Locate the battery compartment on the bottom (Figure 2).
3. Press the arrow on the cover to slide the compartment open.
4. Match the large (–) terminal on the battery to the small terminal on the clip (which lifts out
of the compartment for easier connection).
5. Snap the terminals together firmly.
6. Slide the cover closed.
Note: Now is a good time to record the serial number found on the bottom of your system.
Write it on your warranty card and in the space provided on page 3.
7. Turn the system right side up.
8. Remove the tape from the top front of the system.
CAUTION: After you remove the tape, be sure to remove any CD in the sytem before
turning the system over again. With no tape in place, the CD cover opens freely whenever
the system is turned upside down, so a CD could fall out and be damaged.
Figure 2
Installing the battery
–
+
6
Setting Up
Connecting the power cord
2. Press and hold either Time
or
button to stop the flashing and set the time.
Figure 3
Connecting the power cord
CAUTION: Bose recommends using a quality surge suppressor on all electronic equipment.
Voltage variations and spikes can damage electronic components in any system. A quality
suppressor, which can eliminate the vast majority of failures attributed to surges, may be
purchased at electronic stores.
Connecting the FM antenna
1. Plug the FM antenna into the FM 75Ω EXTERNAL connector on the back of the radio
(Figure 4).
2. For best FM tuning performance, straighten the antenna and extend the arms as far away
from the radio as possible. Avoid placing the antenna next to a metal surface. See the
recommended antenna orientation in Figure 4.
Figure 4
Connecting and setting up the
FM antenna
FM 75Ω EXTERNAL connector
Connecting the coaxial cable
If you subscribe to cable radio or have a connection for an outdoor antenna, you can use the
coaxial cable to connect to the radio.
1. Plug the coaxial cable into the FM 75Ω EXTERNAL connector on the back of the radio
(Figure 4).
2. Connect the other end of the coaxial cable to the outlet in your wall.
CAUTION: Be certain that the installation includes a signal splitter so that only the FM band,
and not the cable TV band, is transmitted to the radio. It is necessary to use a splitter that
filters the signal to prevent any re-emissions of the TV spectrum through the radio.
7
English
1. Plug the power cord into an electric outlet (Figure 3). The display panel lights, and the time
display begins flashing.
Setting Up
English
Installing the remote control battery
WARNING: Mishandling the remote control battery may cause a fire or chemical burn. Keep
the battery away from children. Do not recharge, disassemble, heat above 212˚F (100˚C), or
incinerate the battery. Dispose of the used battery promptly and responsibly.
Your remote control battery may already be installed. If you need to install or replace the
battery follow the instructions below:
Your remote control may be one of two types (Figure 5A or 5B). Each is identified by the way
the battery compartment unlocks.
1. Place the remote control face down on a flat surface.
2. If your remote has a slot on the back (Figure 5A), follow step A. Otherwise, follow step B
and refer to Figure 5B:
A. Insert the tip of a ballpoint pen into the slot. Push to the side as shown and hold. Slide
the battery compartment open with your finger (and, if necessary, remove the battery).
B. Using your finger, push the tab lock to the side as shown and hold. Slide the battery
compartment open (and, if necessary, remove the battery).
Figure 5A or 5B
Installing the battery
Slot
instruSee opera
c
ti
ti
batte ons for tyng
ry to
be uspes of
ed
instr See o
uc pe
batt tions rating
ery for ty
to b pe
e us s of
ed
+ Symbol
A
instr See o
uc pe
batt tions rating
ery for ty
to b pe
e us s of
ed
Tab
B
8
instr See o
uc pe
batt tions rating
ery for ty
to b pe
e us s of
ed
+ Symbol
Setting Up
English
Note: Use only a Duracell, Eveready, Maxell, or Toshiba CR2032 or DL2032 lithium battery
(available at electronics stores). If you have difficulty finding a replacement battery, contact
Bose® Product Support (see phone numbers on the inside back cover).
3. Keeping the remote control face down, insert the new battery into the compartment with
the + symbol facing up.
4. Gently slide the battery compartment closed. It locks automatically.
Caution: Danger of explosion if battery is incorrectly replaced. Replace only with the same
or equivalent type.
9
Setting Up
English
Connecting other components as an option
You can use your Wave® radio/CD to improve the sound of a TV, VCR, computer, or tape player.
Or use it as extension speakers for a Bose® Lifestyle® music system. Connect one of these
components to the R (right) and L (left) AUX IN jacks.
To play your radio or CD player through external speakers, connect powered speakers with an
independent volume control to the system’s R (right) and L (left) LINE OUT jacks. Audio cables
for these connections are available at electronics stores.
Most audio cables are color coded. Match the red plug to the R (red) jack and the black or
white plug to the L (white) jack (Figure 6).
Note: Connecting external speakers does not shut off the Wave® radio/CD’s speakers.
Figure 6
Connecting another component
Using other components
Select your TV, VCR, computer, or tape player, or other auxiliary source by pressing the AUX
button. Adjust the listening volume with the Wave® radio/CD volume buttons. Control all other
functions, including on and off, at the source, referring to its owner’s manual, if necessary. An
auxiliary component cannot be selected as the alarm sound source.
Control your auxiliary powered speakers from the Wave® radio/CD. Use the volume control on
the powered speakers to adjust the volume level.
10
Setting Up
Cable
Portable tape player
One miniplug-tostereo audio cable
Connection at
component
Connection at
Wave® radio/CD
Headphone jack
AUX IN jacks
AUX
IN
For best sound, set
the player volume
control to approximately 3/4 of maximum
volume.
CD changer, tape
deck, or VCR
One stereo audio
cable
Audio output jacks
Bose® Lifestyle®
music system
®
Use a standard RCA
cable for a TV with
stereo output jacks.
Use a standard Y
adapter for a TV with a
single (mono) audio
output jack.
You may need a special
adapter (such as a
miniplug stereo audio
cable) for a TV with a
headphone outlet.
Audio output jacks
Stereo cable with
male-to-male RCA
plugs
TAPE (REC) jacks
Note
L
R
AUX IN jacks
AUX
IN
If there are two sets of
outputs (fixed and
variable), use fixed, so
that the volume can
be controlled from the
Wave® radio/CD.
Television or
computer
English
Component
L
You can record from your Wave®
radio/CD using the connections from
the LINE OUT jacks.
R
AUX IN jacks
AUX
IN
If there are two sets of
outputs (fixed and
variable), use fixed, so
that the volume can
be controlled from the
Wave® radio/CD.
L
R
AUX
IN
AUX IN jacks
To make sure the sound seems to
come from the screen, place the
Wave® radio/CD within a few feet of
the TV. If there is any interference
with the TV picture, move the Wave®
radio/CD farther away.
CAUTION: To prevent interference
with the screen image, keep the
Wave® radio/CD at least 12 inches
from the TV, a computer, or other
monitors.
L
®
R
Powered speakers
with volume
control
Use the audio input
cable that came with
your speakers.
®
Speaker system input
(as described in the
speaker owner’s
manual)
LINE OUT jacks
L
®
R
LINE
OUT
If your powered speaker audio input
cable has three connectors on each
end, use only the two connectors that
look alike to connect to the Wave®
radio/CD outputs. DO NOT USE THE
THIRD CONNECTOR.
Connecting speakers to the LINE OUT
jacks (fixed output) does not shut off
the Wave® radio/CD speakers, although
they can be muted while listening to
the external speakers.
11
Operating Your Wave® radio/CD
English
Using the remote control
You can use the remote control to operate the most frequently used functions of the radio,
CD player, and alarms. Aim the remote control at the display of your Wave® radio/CD. Use the
remote buttons in the same way you use the system control panel.
The remote normally works up to 20 feet in front of the system, and 6 feet to either side.
Replace the remote control battery when it stops operating, or its range seems reduced
(normally every year or two). Keep in mind that lighting and other room conditions, in addition
to battery age, can affect the operating range of an infrared remote control.
You cannot use the remote control to set the time, alarms, CD random and repeat, or radio
presets, nor to customize the display.
Figure 7
Turns system on and sets sleep time,
snoozes (delays) the alarm
®
The Wave radio/CD remote
Turns the system on/off,
deactivates the alarm
On
Off
Sleep
Volume
Turns on CD play or pauses CD
Stops CD
Turns on FM
Turns on AM
Tunes radio, skips or scans CD
FM
AM
Track
Tune
1
2
AUX
Turns on AUX mode
Mute
Mutes/unmutes the system
3
Turns on and selects a preset station
Presets
4
5
Wave Radio/CD
12
Raises or lowers volume
CD
6
Operating Your Wave® radio/CD
Using the Wave radio/CD control panel
®
Using button combinations on the control panel gives you access to additional special
features (such as customizing the display and programming the CD player). For details, refer
to “Quick Reference to Special Functions” on page 25.
Three raised dots on the Sleep/Snooze button of the control panel help you locate this
frequently used button.
Figure 8
The Wave® radio/CD
control panel
Time
Time
Sets the time
Enters Alarm 1 and 2 setup mode
Alarm 1
On/Off
Turns Alarm 1 on/off
Alarm
Setup
Alarm 2
On/Off
Turns Alarm 2 on/off
Presets
Turns on radio and stores/selects
a preset station
1
2
3
4
5
6
Track/Tune
Tunes radio, skips or scans CD
Turns on CD play or pauses CD
Stops CD, turns tone alarm on/off
Turns on FM
CD Play
CD Stop
CD Mode
FM
AM
AUX
Stop
Alarm
Selects CD random/repeat
Turns on AUX (auxiliary mode)
Volume
Turns on AM
Sleep/Snooze
On/Off
Wave Radio/CD
Turns system on/off,
deactivates the alarm
Turns system on and
sets sleep time,
snoozes (delays) the alarm
Raises or lowers
volume
13
English
In addition to controlling the most frequently used functions of the radio, CD player, and
alarms, control panel buttons allow you to set the time, alarms, CD mode, and radio presets
(Figure 8).
Operating Your Wave® radio/CD
Reading the Wave radio/CD display
English
®
Figure 9
The Wave® radio/CD display
Lights when Alarm 1 is
Shows current time,
activated, flashes while
alarm time, sleep
setting Alarm 1, and when
time, snooze time,
going off
Indicates
nap time, AM/FM
tone alarm
frequency, CD time,
is set or
CD program item,
going off
battery level
Indicates
stereo reception
Indicates the
Alarm 1 or 2
status in
setup mode,
shows nap
timer is on
Indicates the
selected source
Lights when Alarm 2 is
activated, flashes while
setting Alarm 2, and when
going off
14
Flashes when
MUTE is
selected
Lights
Indicates when CD is
CD is the
playing,
selected flashes for
source
pause or
low battery
Indicates
AM or PM
Indicates that sleep
or nap timer is
selected
Shows
volume,
FM or AM
preset
number,
CD track
number,
brightness
level
Lights for
presets and CD
programming
Indicates which
CD play mode is
selected
Operating Your Wave® radio/CD
Time
Setting the time
Alarm 1
On/Off
2
5
Alarm 2
On/Off
3
6
Track/Tune
FM
CD Stop
CD Mode
AM
AUX
Stop
Alarm
English
CD Play
Function
Time
Alarm
Setup
Presets
1
4
Volume
Control panel
Sleep/Snooze
On/Off
Wave Radio/CD
To set the clock - Hold down either Time
or button or press the same one twice.
The time display changes slowly at first, then faster. Release the clock set button to stop.
Time
Time
Customizing the display
Function
To set AM/PM (12 hour) or Military (24 hour) time - With the system off, hold
down Alarm Setup and press On/Off to switch between AM/PM (12 hour) and Military
(24 hour) time formats.
To select clock or source display mode - With the system on, hold down Alarm
Setup and press either Preset 1 to select clock display or Preset 2 to select source display.
• In clock display mode, the display shows the time while you are listening to the radio, CD,
or AUX.
• In source display mode, the display shows information about the selected source (radio,
CD, or AUX).
or to show the time momentarily.
• In source display mode, press the Time
To adjust the display brightness - The display dims automatically to medium or low
brightness, as appropriate for low-light room conditions. You can adjust the brightness
setting of the display for both strong light and lowest light environments, but not for the
medium light setting. Turn the system off before setting brightness levels.
• In a strongly lit room, hold down CD Mode
and press Volume ▲ or ▼ to adjust the
setting between 5 and 9 (it is preset to 8).
• In a barely lit room, hold down CD Mode
and press Volume ▲ or ▼ to adjust the
setting between 1 and 5 (it is preset to 2).
• If you do not want the system to dim automatically, set both levels to 5.
To turn off the display - With the system off, hold down CD Mode
and press
On/Off to turn off the main display. The display only lights briefly when you press any
button or while the alarm is sounding. Repeat this step to turn the main display back on.
To check the volume setting when it is not displayed - With the system off or
on, hold down Alarm Setup and press Volume ▲ or ▼ to see the current volume setting.
To check the CD time or radio station frequency when it is not displayed With the system on, hold down Alarm Setup and press Track/Tune
or
to see the CD
time or station frequency.
To check the time when it is not displayed - With the system on or off, press the
Time
or briefly to see the current time.
Hold
Press
and
Alarm
Setup
Alarm
Setup
On/Off
1
2
Time
Time
CD Mode
CD Mode
On/Off
Alarm
Setup
Track/Tune
Track/Tune
Track/Tune
Alarm
Setup
Time
Time
15
Operating Your Wave® radio/CD
English
Time
Alarm 1
On/Off
Controlling the system
Time
Alarm
Setup
Alarm 2
On/Off
On
Off
Presets
1
2
3
4
5
6
Sleep
Volume
CD
Track/Tune
FM
CD Play
FM
CD Stop
AM
1
Control panel
Wave Radio/CD
FM
AM
CD Play
AUX
16
3
Remote control
Presets
4
5
6
Wave Radio/CD
AM
FM
CD
AUX
Volume
To mute the sound - Using the remote control only, press Mute to
silence the system. Press again to restore volume.
To turn on automatically (as a nap timer) - Before setting the
nap timer, select your source and make sure that a radio station is tuned
in or a CD is in the player. Then, on the control panel only, hold down
Alarm Setup and press Sleep⁄Snooze to set the nap timer (to count
down and turn system on).
• The system is silenced and the display shows either – :I0 (minutes) or
the last used nap or sleep time.
• Each additional press (or press and hold) of Sleep⁄Snooze adds 10
minutes, up to – :90. The next press returns to the nap timer OFF
setting.
• You can check the time remaining by holding down Alarm Setup and
pressing Sleep⁄Snooze once.
• After the time counts down, the most recently selected source turns
on.
• Your selected nap time is held in memory for the next use of both
sleep and nap timer.
2
On/Off
To adjust the volume - With the system on or off, press and hold
either button to reset the volume. The display shows the volume level,
from 0 (silent) to 99 (loud). With the system off, the maximum volume
you can preset is 70.
To shut off automatically - Press Sleep⁄Snooze or Sleep to set
sleep time (timed shutoff).
• When sleep time is first set, the display shows :I0 (minutes).
• Press again, or press and hold, to increase the sleep time by
10-minute increments, up to :90. After :90, the next press returns to the
sleep OFF setting, then begins again at :I0.
• Your selected sleep time is held in memory for the next use of both
sleep and nap timer.
Mute
Volume
Sleep/Snooze
On/Off
To turn on/off - Press On/Off once to turn on or off. The system turns
on to the last source played.
To select a source - Press FM or AM, CD Play
, or AUX.
To listen to a component connected to AUX, be sure to turn on the
component. Pressing AUX does not turn on the component.
Track
Tune
AUX
Stop
Alarm
Function
AUX
AM
CD Mode
Mute
Sleep/Snooze
Sleep
Hold
Alarm
Setup
and
Press
Sleep/Snooze
Operating Your Wave® radio/CD
Time
Alarm 1
On/Off
Using the radio
Time
Alarm
Setup
On
Off
Alarm 2
On/Off
Sleep
Presets
1
4
Volume
2
3
5
6
CD
Track/Tune
CD Play
FM
CD Stop
CD Mode
AM
AUX
Stop
Alarm
Function
AM
Track
Tune
AUX
Mute
Volume
1
2
3
Sleep/Snooze
On/Off
Control panel
Wave Radio/CD
To turn the radio on/off - Press On/Off once to turn on or off. The
system turns on to the last source played. Or, press FM or AM or any
Preset to turn the radio on.
To seek a station - Press Track/Tune
or
once to tune in the
next strong station. Repeat to locate a station you prefer. After manually
tuning (see below), wait 2 seconds for the system to return to seek
mode.
4
5
6
Wave Radio/CD
AM
AM
FM
Track/Tune
Track/Tune
Track/Tune
Track
Tune
To manually tune in a station - Tap either Track/Tune
or
button quickly two or more times to tune the frequency in small steps.
Or, press and hold either Track/Tune
or
button until the desired
station is reached. Then, you can press the button to adjust the frequency in small steps. After manually tuning, wait 2 seconds for the
system to return to seek mode.
To preset up to 6 AM and 6 FM stations - Use the Track/Tune
buttons to find the desired station. Then, on the control panel only, hold
down any Preset button until the preset number lights. The station is
now preset to that number.
FM
On/Off
Presets
Remote control
Track/Tune
Track/Tune
Track/Tune
Track
Tune
Presets
Presets
Presets
Track/Tune
Track/Tune
To select a preset station - Change to FM or AM, if needed. Press
the Preset button for the station you want.
To display the selected station - If the display is in clock mode
and the radio is on, press FM (to check FM station) or AM (to check AM
station). Or, if you are not sure of the band, hold down Alarm Setup and
press Track/Tune
or .
1
2
3
4
5
6
Track/Tune
Presets
Presets
Presets
1
1
FM
2
FM
4
FM
Hold
Alarm
Setup
5
2
3
3
AM
Presets
AM
4
6
5
6
AM
and
Press
Track/Tune
FM
AM
Track/Tune
Reading the radio display
Figure 10
An FM radio display example
Indicates FM is the
selected source
Indicates stereo
reception
Shows station frequency
Shows preset number
Lights for presets
17
English
FM
Operating Your Wave® radio/CD
English
Using the CD player
Lift the CD door (as shown). Place the CD, label-side up, on the spindle in the CD well. Gently
lower the door more than halfway, until it begins to close by itself. Or continue to close it
manually if you prefer.
Figure 11
Setting up a CD
®
®
®
Time
Alarm 1
On/Off
Time
Alarm
Setup
On
Off
Alarm 2
On/Off
Sleep
Presets
1
Volume
2
3
5
6
CD
4
Track/Tune
FM
CD Play
FM
Function
CD Stop
CD Mode
AM
AUX
Stop
Alarm
Volume
Control panel
Sleep/Snooze
On/Off
Wave Radio/CD
To turn on/off - Press On/Off once to turn on or off. The system turns
on to the last source played. Or, press CD Play
to turn on the CD
player. In CD mode, the CD begins to play as soon as you load a disc
and close the CD door.
To play or pause the CD - Press CD Play
to play the CD. The
play⁄pause
lights. While playing, press CD Play
to pause the CD.
The play⁄pause
flashes. After 10 minutes paused, the system shuts
off.
To stop the CD - Press CD Stop ■. The display briefly shows the
disc’s total playing time. The number of tracks also shows.
To select a track - In CD mode, press either Track⁄Tune
or
until the desired track is selected.
Pressing Track⁄Tune
skips back to the beginning of the current track. A
second press within 2 seconds skips to the beginning of the previous track.
Pressing Track⁄Tune
at the beginning of the disc skips to the last track.
Pressing Track⁄Tune
at the end of the disc skips to track 1.
To scan through a CD while playing - Press and hold
Track⁄Tune
or
to scan through a track. Release the button to
stop. The display shows the track and playing time. After scanning,
wait 2 seconds to return to track selection.
To scan through a CD while paused - Press and hold Track⁄Tune
or
to scan to the desired location. The play⁄pause
flashes.
Press CD Play
to start at the selected position. Or, after scanning,
wait 2 seconds to return to track selection.
To scan through a CD while stopped - Press Track⁄Tune
or
once to change from total tracks display to track 1. Press and hold
Track⁄Tune
or
to scan to the desired location. Press CD Play
to start at the selected position. Or, after scanning, wait 2 seconds to
return to track selection.
18
AM
Track
Tune
2
CD Play
5
CD
CD
Track/Tune
Track
Tune
Track/Tune
Track
Tune
Track/Tune
Track
Tune
CD
Track/Tune
Track
Tune
CD Play
6
Wave Radio/CD
CD Stop
CD Play
3
Presets
4
CD Play
On/Off
AUX
Mute
Remote control
1
CD
Operating Your Wave® radio/CD
Time
Alarm 1
On/Off
Time
Alarm
Setup
Alarm 2
On/Off
On
Off
Presets
1
2
3
4
5
6
Sleep
Volume
CD
FM
CD Play
CD Stop
CD Mode
AM
AUX
AUX
AM
Track
Tune
FM
Stop
Alarm
Function
Control panel
Wave Radio/CD
To display CD information - If the display is in clock mode (see
page 15) and the CD is playing, hold down Alarm Setup and press
Track/Tune
or
on the control panel only.
Mute
Volume
Sleep/Snooze
On/Off
1
2
3
Remote control
Presets
4
5
6
Wave Radio/CD
Alarm
Setup
Track/Tune
To display playing time for one track - After pressing CD Stop ■,
press Track/Tune
or
to display total time for the selected track.
Press CD Play
to play the selected track.
CD Stop
Track
Tune
Track/Tune
CD
CD Play
To display elapsed or remaining time for a track or disc - In
play or pause mode, hold down Alarm Setup while pressing
on the control panel only to change the display through
CD Play
this sequence; elapsed track time, elapsed disc time, remaining track
time, and remaining disc time.
To select random and/or repeat play - Pressing CD Mode
selects between four random/repeat modes and regular CD play in the
following sequence:
RANDOM (plays all tracks randomly, one time each)
REPEAT RANDOM (repeats the disc in a new random order each time)
REPEAT (repeats the disc continuously)
TRACK REPEAT (repeats the selected track continuously)
TRACK (each track is played in regular order)
Repeat modes stop automatically after 24 hours.
To set continuous music - In CD play mode, to select a source to
play automatically after the CD ends, hold down Alarm Setup and
press FM, AM, or AUX on the control panel only. The selected source
lights on the display. Cancel continuous play by pressing CD Stop ■ or
On/Off.
CD Play
Alarm
Setup
CD Mode
On/Off
CD Stop
Alarm
Setup
FM
AM
AUX
To use the CD hold feature - In CD play mode, if you select
another source, the CD player holds your place for 10 minutes so you
can switch back to CD where you left off.
To program a CD - See “Quick Reference to Special Functions” on
page 25.
Reading the CD display
Figure 12
Indicates CD is the
selected source
A CD display example
Lights when CD is playing,
flashes for pause
Shows CD elapsed time,
CD remaining time,
CD total time,
CD programming
(Pr01, Pr02...)
Shows CD
track number
Lights for CD
programming
Indicates which CD play mode is selected
19
English
Track/Tune
Operating Your Wave® radio/CD
English
Setting the alarms
Time
Alarm 1
On/Off
Time
Alarm
Setup
Alarm 2
On/Off
Presets
®
Note: You can set alarms with the Wave radio/CD on or off.
1
2
4
5
3
6
Track/Tune
CD Play
FM
CD Stop
CD Mode
AM
AUX
Stop
Alarm
Volume
Control panel
Function
Sleep/Snooze
On/Off
Wave Radio/CD
To enter alarm setup mode - Press and release Alarm Setup. The system is now in alarm
setup mode. ALARM 1 flashes for 10 seconds.
Alarm
Setup
To select which alarm to set - While ALARM 1 is flashing, set alarm time, volume, and alarm
sound (tone , radio, or CD), for Alarm 1. Press Alarm Setup again until ALARM 2 is flashing.
While it flashes for 10 seconds, begin to set Alarm 2.
Alarm
Setup
To set the alarm time - While the selected alarm is flashing, press the Time
alarm time. The selected alarm flashes for 10 seconds.
or
to set the
To set the alarm source - While the selected alarm is flashing, press FM, AM, or CD Play
to select and display that source. The tone is no longer selected.
• To reset to tone , press the source currently selected (FM, AM, or CD Play
), which
deselects it.
• When no source is displayed, the alarm is set to tone .
• Setting FM or AM alarm, the station last used for this alarm is shown. Or, use Presets or
Track⁄Tune
or
to select a station.
• Setting CD alarm, track 1 is shown. Or, use Track⁄Tune
or
to select a specific track or time
location for the alarm. Press CD Mode
to select RANDOM or TRACK REPEAT. The CD
plays, repeating as needed, until the alarm shuts off.
• To set radio or CD followed by tone , select radio or CD alarm, then press CD Stop ■.
AUX is not available as an alarm source.
Time
FM
Time
CD Play
AM
Track/Tune
CD Mode
CD Stop
To set the alarm volume - While the selected alarm is flashing, press Volume ▲ or ▼ to set
the alarm volume, from 10 to 99. The selected alarm flashes for 10 seconds.
To test the alarm volume - While the selected alarm is flashing, hold down Alarm Setup and
press Volume ▲ or ▼ to hear the volume setting, as demonstrated by the tone alarm only.
To adjust snooze time - The system is set for a standard 10-minute snooze time (the number
of minutes you can delay the alarm). While the selected alarm is flashing, hold down Sleep⁄Snooze
and press the Time
or to adjust the snooze time (from 1 to 30 minutes) for that alarm. The
number of minutes and Sn appear on the display to confirm your selected snooze time. You can
set a different snooze time for each alarm.
To exit from alarm setup - To leave alarm setup mode, wait 10 seconds for it to disengage.
Or you can press AUX once or Alarm Setup a few times until there is no ALARM 1 or ALARM 2
flashing.
To check the alarm setting - To display the alarm setting for 10 seconds, press and release
Alarm Setup. Press again to display one alarm setup and repeat to display the other alarm setup.
Alarm
Setup
Sleep/Snooze
Time
Time
AUX
Alarm
Setup
Alarm
Setup
Reading the alarm setup displays
Figure 13
Examples of alarm setup
displays
1
3
Alarm
Setup
Alarm
Setup
ALARM 1 flashes. You can begin by setting the time.
2
4
FM
CD Play
Pressing FM selects it as the source for ALARM 1.
20
ALARM 2 flashes. You can begin by setting the time.
Pressing CD selects it as the source for ALARM 2.
Operating Your Wave® radio/CD
Using the alarms
Time
Time
Alarm
Setup
On
Off
Alarm 2
On/Off
Sleep
Presets
Volume
1
2
3
4
5
6
CD
Track/Tune
FM
CD Play
CD Stop
CD Mode
FM
AM
AUX
Stop
Alarm
Function
Sleep/Snooze
Control panel
On/Off
Wave Radio/CD
3
Remote control
Presets
4
5
6
Wave Radio/CD
Alarm 2
On/Off
On/Off
Sleep/Snooze
Sleep
Time
Time
To change the volume of the alarm while it is sounding - The
radio, CD, and tone alarms turn on and gradually increase to the
selected volume setting. To change the volume for one use only, press
Volume ▲ or ▼ while the alarm is sounding.
To use the alarm during a power failure - On the control panel
only, press On/Off to silence. The backup battery maintains the alarm for
approximately 24 hours without AC power. To conserve power in backup
mode, (1) only the tone alarm sounds (even if radio or CD alarm is
selected), (2) the display is off, and (3) the remote does not operate the
system. Normal operation resumes when power is restored. Replace the
9V battery after an extended power failure.
AUX
Mute
2
Alarm 1
On/Off
To stop the alarm - Press On/Off. The alarm indicator remains lit,
since the alarm automatically resets to repeat daily. Use the Alarm 1 or
Alarm 2 button to deactivate the alarm.
Or, if you do not press On/Off, the tone alarm shuts off in 30 minutes,
the radio or CD alarm shuts off in 60 minutes. If the alarm is set for radio
or CD followed by tone , the music plays for 10 minutes, then the
tone sounds for 30 minutes.
To use the snooze option - Press Sleep⁄Snooze or Sleep to have
the alarm snooze for either 10 minutes or your customized snooze time.
(See instructions for adjusting snooze time on page 20.) During the delay,
the ALARM icon flashes and Sn appears on the display. After the silent
snooze time, the alarm begins again as you have set it.
To change the duration of the current snooze only, press Sleep⁄Snooze or
Sleep once to display the remaining snooze time. Press the Time
or
while remaining snooze time is displayed to increase or decrease the time.
You can repeat the snooze cycle as many times as you wish.
Track
Tune
Volume
1
To turn Alarm 1 or Alarm 2 on/off - On the control panel only,
press Alarm 1 to activate; ALARM 1 lights on the display. Press again to
deactivate Alarm 1. Press Alarm 2 to activate; ALARM 2 lights on the
display. Press again to deactivate Alarm 2.
The alarms go off at the time, volume, and source you have set for each.
AM
Volume
On/Off
21
English
Alarm 1
On/Off
Maintaining Your Wave® radio/CD
Taking care of your Wave radio/CD
English
®
The only necessary maintenance is cleaning and periodic battery replacement.
Handling CDs
Handle discs by their edges to prevent fingerprints and scratches.
To remove stains or fingerprints from the surface of a disc, use a soft,
lint-free, dry cloth. Wipe in straight movements from the center of the
disc to the outside. Do not use any chemical products; they can
damage the disc.
Do not write on, or attach labels to the surface of the disc.
To minimize exposure to dust and dirt, replace discs in their cases after
use. Store each disc in its case, out of direct sunlight, high temperatures, and humidity.
Cleaning your Wave radio/CD
®
Use only a cloth to clean the outside of the Wave® radio/CD. If necessary, you may use a soft-bristled attachment to gently vacuum the
front of the system.
Do not use any solvents, chemicals, or cleaning solutions containing
alcohol, ammonia, or abrasives. Do not spray cleaners directly on the system. Do not allow
liquids to spill into any openings on the system.
CAUTION: If liquids get into the product, turn the system off. Call Bose® Product Support as
soon as possible to arrange for service (see phone numbers on inside back cover).
Replacing the batteries
To maintain your Wave® radio/CD’s memory and backup alarm system, replace the 9V battery
every year or whenever you have an extended power loss. A dead battery may leak and
cause damage. Do not unplug your Wave® radio/CD from the power outlet while replacing the
battery. If you do unplug it, you will need to reset the clock and alarm settings.
Follow these steps to check the low-battery indicator:
1. Turn the system off.
2. Hold down Alarm Setup, and press CD Stop. The display indicates the remaining battery
power:
• Hi or number 78 or above mean adequate voltage to provide backup power.
• Number 77 or below means limited voltage.
• Lo means the voltage is too low for the battery to function. The play/pause
to alert you to replace the battery soon.
flashes
For further information on replacing the backup battery, see “Installing the battery” on page 6.
For information on replacing the remote control battery, see “Installing the remote control
battery” on page 8.
Technical information
Power rating
Weight
USA/Canada: 120V~ 50/60 Hz 50W
3.4 kg
International: 220-240V~ 50/60 Hz 50W
Dimensions
35.6 cm x 21.6 cm x 11.1 cm
22
Maintaining Your Wave® radio/CD
Troubleshooting
What to do
System does not function
• Make sure the power cord is fully plugged into an operating AC wall outlet.
• Press On/Off to see if the display lights. The main display may be turned off (see page 15).
No sound
•
•
•
•
•
•
Increase the volume.
Press the Mute button on the remote control to unmute the sound.
Be sure CD is loaded correctly.
Check the connections for any auxiliary component.
Select AUX to hear a source connected to the AUX IN jacks.
Be sure that the component connected to AUX IN is turned on.
Remote control
is inconsistent
or does not work
•
•
•
•
Check remote control battery and its polarity (+ and –).
Replace battery, if necessary (see page 8).
Operate the remote control closer to the system.
Check for interference from room lighting or sunlight, or for dust or dirt on the lens. Try the
system in a different location.
AM reception is weak
• Adjust the internal AM antenna by turning the Wave® radio/CD slightly to one side or
the other.
• Move the radio farther from a TV, refrigerator, fluorescent lights, halogen lamps, dimmer
switches, or other electronic equipment that generates electrical noise.
• If neither suggestion works, you may be in an area of weak AM signal coverage.
FM reception is weak
•
•
•
•
•
If you are using the supplied antenna, check the antenna connection.
Straighten and extend the arms of the antenna as far away from the radio as possible.
Try moving the FM antenna near a window.
If you are using the supplied coaxial cable, be sure it is connected securely.
Contact your cable radio company for further assistance.
CD does not play
•
•
•
•
•
•
Check to see if the play/pause in the display is lit.
If the play/pause is flashing, the disc is paused. Press CD Play
to play.
Check to see if there is a disc in the player, label-side up.
There may be dust or dirt on the CD. Clean the CD. See “Handling CDs” on page 22.
The disc may be defective. Try another disc.
Verify that disc is not a DVD.
Display does not show the
expected information
• Check “Customizing the display” on page 15 or “Quick Reference...” on page 25 to change
the display settings (12 or 24 hour clock, display on or off, elapsed or remaining CD time).
• Unplug and reconnect the system to return to original settings.
Customer service
For additional help in solving problems, contact Bose® Product Support. See the inside back
cover for Bose Corporation offices and phone numbers.
23
English
Problem
English
Maintaining Your Wave® radio/CD
Limited warranty
What is covered:
All parts defective in material or workmanship.
For how long:
One year from the purchase date.
What we will do:
We will, at our sole option, repair or replace any defective parts free of charge. We will also
pay shipping or transportation charges from you to us, and from us to you.
What you must do:
A. Call Bose® Customer Service and ask for shipping instructions.
B. Properly pack the unit, if possible in the original carton for shipping.
Other conditions:
This warranty is fully transferable for the one-year period following purchase.
THE PROVISIONS OF THIS WARRANTY ARE IN LIEU OF ANY OTHER WARRANTY,
WHETHER EXPRESS OR IMPLIED, WRITTEN OR ORAL, INCLUDING ANY WARRANTY OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. THE MAXIMUM LIABILITY OF BOSE SHALL NOT EXCEED THE ACTUAL PURCHASE PRICE PAID BY YOU FOR
THE PRODUCT. IN NO EVENT SHALL BOSE BE LIABLE FOR SPECIAL, INCIDENTAL,
CONSEQUENTIAL, OR INDIRECT DAMAGES.
This warranty does not cover a defect that has resulted from improper or unreasonable use or
maintenance, accident, improper packing, or unauthorized tampering, alteration, or modification as determined solely by us. This warranty is void if the label bearing the serial number
has been removed or defaced.
Other Legal Rights:
This warranty gives you specific legal rights, and you may also have other rights which vary
from state to state or country to country. Some places do not allow limitations on implied
warranties or the exclusion or limitation of incidental or consequential damages, so the above
limitations or exclusions may not apply to you.
24
Quick Reference To Special Functions
Time
Alarm 1
On/Off
Time
Alarm
Setup
Alarm 2
On/Off
Presets
2
5
3
6
Track/Tune
CD Play
FM
CD Stop
CD Mode
AM
AUX
Stop
Alarm
Volume
Sleep/Snooze
On/Off
Hold
and
Wave Radio/CD
Press
Sleep/Snooze
Alarm
Setup
Use when...
system is on or off
To use the nap timer
Sleep/Snooze
Time
Function
Time
Alarm
Setup
see page 16
in alarm setup mode
To adjust the snooze time
see page 20
in alarm setup mode
To test the alarm volume
Alarm
Setup
CD Stop
CD Mode
see page 15
system is off
To check backup battery power level
see page 22
system is off
To adjust the display brightness
CD Mode
see page 15
system is off
To turn the display on/off
On/Off
Alarm
Setup
see page 15
volume setting is not displayed
To check the volume setting
see page 15
Track/Tune
Alarm
Setup
To check the CD time or radio station frequency
Alarm
Setup
display is in clock view or off
To display elapsed or remaining time for a track or disc
CD Play
FM
Alarm
Setup
system is off
To set AM/PM (12 hour) or Military (24 hour) time
On/Off
Alarm
Setup
see page 20
see pages 15, 17, 19
in play or pause mode
in CD mode
AM
or
see page 19
To set continuous music
see page 19
AUX
To program a CD - You can program up to 32 CD tracks.
1. Place the selected disc in the CD player.
CD Stop
Alarm
Setup
CD Stop
Track/Tune
Track/Tune
2. Press CD Stop ■.
3. Hold down Alarm Setup and press CD Stop ■. The display shows Pr01 to indicate
programming mode is ready for your first selection.
4. Use Track/Tune
Alarm
Setup
CD Mode
Track/Tune
Track/Tune
or
to select a track.
5. Hold down Alarm Setup and press CD Mode
counter shows Pr02 for the next selection.
to program this track. The program
6. Continue to select tracks (Pr03, Pr04, etc.) until your list is complete.
Track/Tune
Track/Tune
Alarm
Setup
CD Play
CD Mode
7. To look through your programmed list, hold down Alarm Setup and press Track/Tune
or . You can change an item while you are viewing it by following steps 4 and 5. To
add more items at the end of your list, reprogram (step 5) the last entry to continue
adding selections.
8. Press CD Play
to play the selected tracks once each. The programmed tracks are
shown with the PRESET icon lit.
9. To erase the program, press CD Mode
.
Note: Your program is saved until erased. The program plays all applicable track
selections for any disc in the CD player.
25
English
1
4
Index
English
A
acoustic waveguide 4
Alarm 1 13, 14, 20, 21
Alarm 2 13, 14, 20, 21
ALARM 1 or 2 indicator 20, 21
Alarm Setup 13, 15-17, 19, 20, 26
alarm time 14, 20
alarm volume 20, 26
alarms 4, 10, 12, 13, 20, 21
AM 4, 5, 12-14, 16, 17, 19, 20, 23
AM antenna 23
AM reception 5, 23
AM/FM 17
AM/PM (12 hour) time 15, 26
antenna connector 7
automatic shutoff 16
automatic turn on 16
AUX 10-13, 15, 16, 19, 20, 23
AUX IN jacks 10, 11, 23
auxiliary source 10, 23
B
backup alarm 6, 22
bass 4, 5
batteries 2, 5, 22, 23
battery (remote control) 4, 8, 12, 22, 23
battery backup 4, 6, 21
battery carrier 8, 9
battery compartment 6, 8
battery voltage 14, 22
brightness level 14, 15, 26
C
cable radio signal 7
CD 4, 5, 7, 10-14, 16, 18-23, 26
CD changer 11
CD door 6,18
CD hold 19
CD Mode 13, 15, 20, 26
CD player 4, 10, 12, 13, 18, 19, 26
CD programming 4, 13, 14, 19, 26
CD Stop 18, 20
CD time 15, 23, 26
cleaning 22
clock 15, 17, 19, 20, 22
clock display 15, 23, 26
clock mode 17, 19
clock set 15, 20
coaxial cable 7
compact disc 2
computer 4, 5, 10, 11
connections 23
continuous music 19, 26
control panel 12, 13, 15-21, 26
countdown 16
customer service 23
26
D
dim setting 14, 15, 26
dimensions 22
dimmer switch 23
disc 2, 18, 19, 22, 23, 26
display 6, 7, 12-23, 26
display brightness 14, 15, 26
DVD disc 23
E
elapsed disc time 19
elapsed time 19, 23, 26
elapsed track time 19
electrical noise 23
external antenna 7, 23
F
fluorescent lights 23
FM 4, 7, 12-14, 16, 17, 19, 20, 23
FM 75Ω EXTERNAL antenna connector 7
FM antenna 7, 23
FM reception 7, 23
frequency 14, 15, 17, 26
H
heat 5, 8
I
infrared 4, 12
interference 11, 23
L
Lifestyle® music system 10, 11
LINE OUT jacks 10, 11
lithium battery 9
location of system 5, 23
low-battery indicator 22
M
memory 6
military (24 hour) time 15, 26
moisture 2
monitor 5, 11
music center 23
Mute button 23
mute 14, 16
N
9V battery 5, 6, 21, 22
nap timer 14, 16, 26
O
ON/OFF button 13, 21
On/Off 15-19, 21, 23
Index
R
radio display 17
radio reception 7, 23
radio station 15, 16, 26
RANDOM 19
random modes 4, 13, 19, 20
RCA cable 11
remaining disc time 19
remaining time 16, 19, 21, 23, 26
remaining track time 19
remote control 4, 5, 8, 9, 12, 13, 16-19, 21-23
REPEAT 19
repeat modes 4, 13, 19, 20, 21
T
tape player 4, 10, 11
television 5, 11
time 2, 7, 12-15, 21, 26
timed shutoff 16
tone 21
tone alarm 13, 14, 21
total disc time 19
track 14, 18-20, 26
Track/Tune 15, 17, 18, 19, 26
transparent film 6
troubleshooting 23
turn on automatically 16
tuning 4, 12, 13, 17-19
TV 4, 7, 10, 11, 23
English
P
pause 14, 18, 19, 23, 26
play 12-4, 18, 19, 23, 26
playing time 18, 19
portable tape player 11
power cord 7, 23
power failure 6, 21, 22
power rating 22
powered speakers 10
Pr01 19, 26
PRESET indicator 17
preset number 14, 17
preset station 12, 13, 17
Preset buttons 20
presets 4, 14, 17
product support 5, 9, 22, 23
programming a CD 4, 13, 14, 19, 26
U
unmute 23
unpack 5
V
VCR 4, 10, 11
voltage 2
volume 10-13, 15, 16, 20, 21, 23
volume control 10, 11
volume setting 15, 21, 26
W
warranty 3, 6, 24
waveguide 4
weight 22
S
safety information 2
scan 4, 12, 13, 18
seek 17, 18
serial number 3, 6
shut off automatically 16
signal splitter 7
skip 4, 12, 13, 18
sleep mode 12-14, 16, 20, 21
Sleep/Snooze button 13
Sn 20, 21
snooze mode 12-14, 16, 20, 21, 26
source display 15, 20, 23, 26
splitter 7
station frequency 15, 17, 26
station presets 4, 12, 13, 17
stereo reception 17
stereo tuner 4
27
Bose® Corporation
USA & Canada Sales
Bose Corporation, The Mountain
Framingham, MA 01701-9168
1-800-637-8781
USA & Canada Service
Bose Corporation, The Mountain
Framingham, MA 01701-9168
1-800-637-8781 or
508-879-7330, x63055
European Office
Bose B.V., Nijverheidstraat 8
1135 GE Edam, Nederland
TEL 0299-390111
FAX 0299-390114
Australia
Bose Pty Limited
1 Sorrell Street
Parramatta NSW, 2150
TEL 02 9204-6111
FAX 02 9204-6122
Deutschland
Postfach 1468
48504 Nordhorn
TEL 0800-2673555
FAX 05921-724250
France
6, Rue Saint Vincent
78100 Saint Germain en Laye
TEL 01-3061 6363
FAX 01-3061 4105
Nederland
Nijverheidstraat 8
1135 GE Edam, Nederland
TEL 0299-390111
FAX 0299-390114
United Kingdom
Freepost (EX 151)
Exeter
EX1 1ZY
TEL 0800 614 293
FAX 0870 240 2013
World Wide Web
www.bose.com
31
©2004 Bose Corporation
The Mountain, Framingham, MA 01701-9168 USA
251771-ENGvo AM Rev.04
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement