- Computers & electronics
- Audio & home theatre
- Soundbar speakers
- Bang & Olufsen
- BeoLab 2000
- User's Guide
Bang & Olufsen BeoLab 2000 User`s guide
Add to my manuals12 Pages
Bang & Olufsen BeoLab 2000 lets you listen to any audio or video source from your main Bang & Olufsen system in another room. It can be controlled via its own interface or with the Beo4 remote control. It allows you to adjust the volume, change tracks, and switch between sources. It can also be integrated into Timer Play programming for your main system.
advertisement
B E O L A B 2 0 0 0
The BeoLab 2000 gives your main
Bang & Olufsen system an extra dimension.
Now you can play any audio or video source you like in your main system and listen to it – via your BeoLink installation – in the room with your
BeoLab 2000.
But this is not all. You can even control the daily playback functions in your main system via the BeoLab
2000.
This guide explains how...
1
User’s guide
2
This guide describes how to operate the
BeoLab 2000, and how to operate your main
Bang & Olufsen system via the BeoLab 2000.
The separate Setting-up guide, which is also enclosed, describes how to install the system and make the BeoLab 2000 ready for use.
Note: The BeoLab 2000 is designed to be used in a
Bang & Olufsen BeoLink system (ML) only. Please contact your Bang & Olufsen dealer for further information.
C O N T E N T S
4 Nice to know about...
Music in other rooms
6 Close-up operation
Sound control
7 Volume adjustment
Timer Play control
8 Remote operation
Using the Beo4 remote control
9 Controlling your main system
10 Beo4 extra functions...
11 Presetting the volume level
3
4
..Music in other rooms
N I C E T O K N O W A B O U T …
BANG & OLUFSEN
The BeoLab 2000 gives your main Bang
& Olufsen system an extra dimension:
• Now you can listen to any source you like from your main system (audio or video) in the room with your BeoLab
2000.
• And you can even operate functions in your main system directly on the
BeoLab 2000 – or using the Beo4 remote control.
All you have to do, is connect the
BeoLab 2000 to your BeoLink installation, and your main Bang & Olufsen system can be used in that room as well.
The BeoLab 2000 fits in easily wherever you want music: You can place it in a corner; you can hang it on the wall; or you can place it standing on a shelf or a sideboard.
No matter how, the two active speakers in the BeoLab 2000 will give you the full benefit of the high-quality stereo sound produced by your main
Bang & Olufsen system.
Operating the BeoLab 2000 close-up, you can:
• Listen-in on the source that is currently playing in your main Bang & Olufsen system; or switch on to the radio (or TV) program that was last playing.
• Switch on the radio, the CD player, or the audio tape recorder in your main system.
• Step through radio or TV programs, or tracks on a tape or a CD.
• Adjust the volume level in the two BeoLab 2000 loudspeakers – quite independently of your main system.
• Include the BeoLab 2000 in a Timer Play programming of your main system.
Using the Beo4 remote control, you can:
• Switch on any source you like in your main
Bang & Olufsen system (audio / video) via the
BeoLab 2000.
• Operate a number of functions for the source you are listening to on the BeoLab 2000.
• Preset your preferred volume level in the
BeoLab 2000.
Your main Bang & Olufsen system (audio, video, or AV) and your BeoLab 2000 must be interconnected by a Bang & Olufsen BeoLink installation (ML).
You can then listen to any source you like from your main system (and control the source) in the room with your BeoLab 2000.
5
6
C L O S E - U P O P E R A T I O N
Sound control
To switch on the BeoLab 2000 you must either press the circular PLAY • button in the end of the operation panel; or you must press one of the three audio buttons (TV, CD, or RADIO):
Another way of switching on, is to press the specific button for the source you want to listen to from your main audio system: TV (TV), CD (CD player), or RADIO (radio).
The PLAY • button enables you to listen-in on your main Bang & Olufsen system if it is currently playing. Just press PLAY • once!
If your main system is not playing, pressing PLAY • will switch on the radio* at the program that was last playing.
No matter how you switch on, the sound from your main system will be heard instantaneously in the BeoLab
2000 speakers.
While you are listening to the BeoLab
2000, you can step through your radio
(or TV) programs; or through the tracks on the CD or the tape you are listening to. Just press the twin-button marked
▲ or ▼ – repeatedly.
If you press PLAY • again briefly, the
BeoLab 2000 switches off.
Note: If you press the PLAY • button for two seconds or more, both the BeoLab 2000 and your main system will switch off.
* Note: If your main Bang & Olufsen system consists of a video system only (with no audio sources), pressing PLAY • will switch on the TV program that was last playing.
The small BeoLab 2000 operation panel has six push-buttons and a volume control button for close-up operation.
Below the operation panel there is a small display. The red light to the left in the display is a stand-by indicator. The red light changes to green when the BeoLab
2000 is switched on. The red light to the right in the display indicates that the
Timer Play function is cut in.
PLAY
Volume adjustment
The BeoLab 2000 always switches on at the same, preset volume level.
Volume is adjusted quite independently of your main Bang & Olufsen system.
The volume control (turn-button to the right on the operation panel) allows you to turn the volume up or down as you like.
Note: See how to preset the volume start-up level in the BeoLab 2000 on page 11.
• If your main Bang & Olufsen system is in stand-by when you switch on the BeoLab
2000, you will only get sound in the BeoLab
2000 speakers – the loudspeakers in your main system will not be cut in.
• If you try to switch on a source in your main
Bang & Olufsen system, and you get the sound from a different source (or no sound at all) in your BeoLab 2000 speakers, it may be because a recording is progressing in your main system. This special “lock” function ensures that the recording will not be spoiled.
• If there is no light to the left in the display
(no stand-by indicator), it may be because the mains-switch on the back of the BeoLab
2000 is switched off. Please refer to the section Ready for use in the Setting-up guide for further information.
7
Timer Play control
If you have programmed your main
Bang & Olufsen system to start playing automatically (Timer Play) – for example to wake you up in the morning, you can include the BeoLab
2000 as well.
To do so, just press the TIMER button on the operation panel.
A small red light then appears in the display (just below the TIMER button).
The red light indicates that the BeoLab
2000 will be included as well, whenever your main system starts playing a Timer Play programming.
Press TIMER again if you want to cut out the Timer function (the red light disappears).
> Note: The Beo4 remote control enhances the possibilities and gives you the full benefit of your BeoLab 2000 (see pages 8-11).
8
TV
SAT
LIGHT RADIO
DVD CD
V TAPE RECORD A TAPE
7
4
1
TEXT
8
5
2
0
9
6
3
MENU
R E M O T E O P E R A T I O N
Using the Beo4 remote control
The Beo4 remote control gives you the full benefit of your BeoLab 2000.
Furthermore, Beo4 is the key to presetting the volume level in the
BeoLab 2000 loudspeakers.
With the Beo4 remote control you can switch on any source you wish to listen to from your main Bang & Olufsen system (audio/video), and control the daily playback functions for that source in the room with your BeoLab 2000.
The Beo4 remote control and the
BeoLab 2000 both respond readily to your instructions – giving you sound in the speakers within seconds after pressing the button.
Operation is then carried out just as if you were operating your main system directly, using the Beo4 remote control.
See how on the next few pages...
GO
Any remote operation you make is received by the BeoLab 2000.
Via your BeoLink installation, the BeoLab
2000 communicates your instruction to your main Bang & Olufsen system.
LIST
STOP
EXIT
The Beo4 remote control is available as an optional extra at your Bang & Olufsen dealer.
Please refer to the Beo4 User’s guide for information about the remote control and its principles of operation.
B E O C E N T E R 9 3 0 0
Controlling your main system
Via your BeoLab 2000, you can switch on any source you like (audio/video) from your main Bang & Olufsen system, and listen to it on the BeoLab 2000 speakers.
To do so, simply press the appropriate source button on the Beo4 remote control.
Note: If you keep pressing the stand-by button • for two seconds or more, you will switch off both the BeoLab 2000 and your main Bang & Olufsen system.
Note: The functions mentioned in this guide are only available from the BeoLab 2000 in so far as the source in question is included in your main
Bang & Olufsen system – and provided the source supports the function.
While the source is playing, you can adjust the volume level, switch programs, listen to specific tracks or
CDs, stop and resume playback, etc.
For further information about these functions, please refer to the User’s guide for your main
Bang & Olufsen system.
Switches on the radio
Starts the CD player
Starts the audio tape recorder
Switches on the TV
Switches on to satellite
Starts the video tape recorder
Raises the volume
Lowers the volume
The button to the right on this page show you how...
To switch off the BeoLab 2000 simply press the red stand-by button • on the
Beo4 briefly.
Press to step through your programs; or to step from track to track on a
CD or a tape
Alternatively, key in the exact program you want or track number on a single CD player
Please note...
The functions mentioned on this page can also be operated using the
Bang & Olufsen Beolink 1000 remote control. You will find that the texts and symbols on the buttons of the two remote controls are almost the same – (only, you must press PLAY instead of GO).
Note: Pressing the Beolink 1000 MUTE button, while the BeoLab 2000 is in stand-by, corresponds to pressing
PLAY • directly on the BeoLab 2000
(see page 6).
On a audio or videotape recorder and single CD player…
Rewinds a tape, searches backwards on a CD in a single CD player
Fastforwards a tape, searches forwards on a CD in a single CD player
Press to resume playback or
0 through
9 ss s s or
GO
> See the next page for further information...
RADIO
CD
A TAPE
TV
SAT
V TAPE
9
10
> Remote operation – Controlling your main system or tt ss
1 through
6
On a multi CD player…
Press to change to the next or previous CD
Key in a disc number directly to play a particular CD or
LIST then
1
1
Press to search forwards on a CD
Press to search backwards on a CD
To select a particular track on one
CD…
Press until TRACK* is displayed
Key in a track number, e.g.
number11
STOP
GO
Press to pause your CD player, or your audio or video tape recorder
(Press STOP twice to stop the video)
Press any time to resume playing
Beo4 extra functions...
• Pressing ∧ and ∨ simultaneously on the Beo4 remote control, while the BeoLab 2000 is in stand-by, corresponds to pressing PLAY • directly on the BeoLab 2000 (see page 6).
• To “turn” the tape in your audio tape recorder to play the other side, press the Beo4
LIST button to display TURN*, then press the
GO button.
• To switch mono/stereo sound or language on a radio, TV or satellite program, or to switch sound track on a video tape, press the LIST button to display SOUND*, then press GO
(repeatedly).
• To play the tracks on a CD in ramdom order, press LIST to display RANDOM, then press GO.
• To start playback on a Bang & Olufsen record player, press LIST until the display reads
PHONO *, then press GO. Pressing ▲ or ▼ while the record is playing, makes the record player step through the music.
• To start playback on a secondary audio- or video tape recorder, or a secondary CD player in your main Bang & Olufsen system, press the
Beo4 LIST button to display A.TAPE2*, V.TAPE2*, or CD2*, then press GO.
• To switch on a DVD or CDV player connected to your main video system, press DVD on
Beo4.
• If you use your BeoLab 2000 in the same room as your main Bang & Olufsen system, you must program the BeoLab 2000 accordingly (see how in the Setting-up guide). In that case, to start playing a source in your main system via your BeoLab 2000, press the Beo4 LIST button to display LINK*, then press RADIO, CD,
A TAPE, TV, SAT, or V TAPE. The index in the
Beo4 User’s guide gives information about the
Beo4 remote control and“LINK”.
*Note: In order to display TURN, SOUND, PHONO,
A.TAPE2
, V.TAPE2, CD2, CDV, or LINK on Beo4, you must add the cues to Beo4’s list of functions, please refer to Beo4’s own User’s guide for further instruction.
• Press briefly to switch off the
BeoLab 2000
*Note: In order to display TRACK on Beo4, you must add the function to the Beo4 list of functions, please refer to Beo4’s own User’s guide and the chapter, Customising your Beo4, for further instruction.
Note: The functions mentioned here are only available in so far as they are supported by your main Bang & Olufsen system.
Presetting the volume level
When you have adjusted the volume level in the BeoLab 2000 speakers, the
Beo4 remote control enables you to preset the level in the BeoLab 2000 so that it always switches on at that level.
All you have to do, to turn your adjustment into a permanent setting, is find the cues A.SETUP* and then
S.STORE* in the Beo4 display and press
GO.
Note: The BeoLab 2000 always returns to the preset volume level when you switch it to standby, but you can also make it return to the preset level by pressing the Beo4 LIST button to display
RESET *, then press GO.
Adjust the volume level to your liking
Press until A.SETUP* is displayed
*Note: In order to display A.SETUP on Beo4 and
S.STORE
which will then appear automatically, you must add the function to the Beo4 list of functions. You must also add RESET to the Beo4 list of functions. Please refer to Beo4’s own User’s guide and the chapter, Customising your Beo4, for further instruction.
Press to be able to store
Press until S.STORE* is displayed
Press to store the current setting or then
LIST
GO
LIST then
GO
11
12
Date purchased
Contact person
Dealer
Telephone
Address
Record your serial numbers here:
BeoLab 2000
Beo4 remote control
N O T E S
Dear Customer,
Your needs as the user of our products are always given careful consideration during the design and development process, and we strive to make our products easy and comfortable to operate.
We therefore hope that you will take time to drop us a line, telling us about your experiences with your Bang & Olufsen system. Anything which you consider important – positive or negative – may help us in our constant efforts to refine our products.
Thank you!
Please write to:
Customer information dept. 7240
Bang & Olufsen a/s
DK-7600 Struer
Denmark
3508226
0001
Printed in Denmark by
Bogtrykkergården a-s, Struer
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project