A&D | UA-1020 | Instruction manual | A&D UA-1020 Instruction manual

Digital Blood Pressure Monitor
Model UA-1020
Instruction Manual
Original
Manuel d’instructions
Traduction
Manual de Instrucciones
Traducción
Manuale di Istruzioni
Traduzione
使用手冊
翻譯
1WMPD4002224C
Contents
Dear Customers.................................................................... 2
Preliminary Remarks ............................................................. 2
Precautions........................................................................... 2
Parts Identification................................................................ 4
Symbols................................................................................ 5
Operation Mode.................................................................... 7
Using the Monitor ................................................................. 8
Installing / Changing the Batteries ................................... 8
Connecting the Air Hose .................................................. 8
Connecting the AC Adapter.............................................. 8
Adjusting the Built-in Clock ............................................. 9
Selecting the Correct Cuff Size ......................................... 9
Applying the Arm Cuff ................................................... 10
How to Take Accurate Measurements............................. 10
Measurement ................................................................. 10
After Measurement ........................................................ 10
Measurements .................................................................... 11
Normal Measurement..................................................... 11
Measurement with the SET Pressure ............................. 12
Measurement with the Desired Systolic Pressure ............ 12
Notes for Accurate Measurement ................................... 13
TriCheckTM Measurement .................................................... 12
Recalling the Memory Data ................................................. 15
What is an Irregular Heartbeat............................................. 16
Pressure Bar Indicator ......................................................... 16
WHO Classification Indicator ............................................... 16
About Blood Pressure.......................................................... 17
What is Blood Pressure? ................................................. 17
What is Hypertension and How is it Controlled?.............. 17
Why Measure Blood Pressure at Home?........................... 17
WHO Blood Pressure Classification ................................. 17
Blood Pressure Variations............................................... 17
Troubleshooting ................................................................. 18
Maintenance ....................................................................... 19
Technical Data .................................................................... 19
English 1
Dear Customers
Congratulations on purchasing a state-of-the-art A&D blood pressure
monitor, one of the most advanced monitors available today. Designed
for ease of use and accuracy, this device will facilitate your daily blood
pressure regimen.
We recommend that you read through this manual carefully before
using the device for the first time.
Preliminary Remarks
This device conforms to the European Directive 93/42 EEC for Medical
Products. This is made evident by the
mark of conformity.
(0123: The reference number to the involved notified body)
The device is designed for use on adults only, not newborns or infants.
Environment for use: The device is for use in the home healthcare environment.
This device is designed to measure blood pressure and pulse rate of people
for diagnosis.
Precautions
Precision components are used in the construction of this device. Extremes
in temperature, humidity, direct sunlight, shock or dust should be avoided.
Clean the device and cuff with a dry, soft cloth or a cloth dampened with
water and a neutral detergent. Never use alcohol, benzene, thinner or
other harsh chemicals to clean the device or cuff.
Avoid tightly folding the cuff or storing the hose tightly twisted for long
periods, as such treatment may shorten the life of the components.
The device and cuff are not water resistant. Prevent rain, sweat and water
from soiling the device and cuff.
Measurements may be distorted if the device is used close to televisions,
microwave ovens, cellular telephones, X-ray or other devices with strong
electrical fields.
Used equipment, parts and batteries are not treated as ordinary
household waste, and must be disposed of according to the applicable
local regulations.
When the AC adapter is used, make sure that the AC adapter can be
readily removed from the electrical outlet when necessary.
When reusing the device, confirm that the device is clean.
Do not modify the device. It may cause accidents or damage to the device.
To measure blood pressure, the arm must be squeezed by the cuff hard
enough to temporarily stop blood flow through the artery. This may cause
pain, numbness or a temporary red mark to the arm. This condition will
appear especially when measurement is repeated successively.
Any pain, numbness, or red marks will disappear with time.
English 2
Contraindications
The following are precautions for proper use of the device.
Do not apply the cuff to an arm with another medical electrical equipment
attached. The equipment may not function properly.
People who have a severe circulatory deficit in the arm must consult a
doctor before using the device, to avoid medical problems.
Do not self-diagnose the measurement results and start treatment by yourself.
Always consult your doctor for evaluation of the results and treatment.
Do not apply the cuff on an arm with an unhealed wound.
Do not apply the cuff on an arm receiving an intravenous drip or blood
transfusion. It may cause injury or accidents.
Do not use the device where flammable gases such as anesthetic gases
are present. It may cause an explosion.
Do not use the device in highly concentrated oxygen environments, such as a
high-pressure oxygen chamber or an oxygen tent. It may cause a fire or explosion.
English 3
Parts Identification
Display
DC Jack
Button
Button
Air Connector Plug
Arm Cuff
SET Button
START Button
Air Hose
Air Socket
Battery Compartment
Battery Cover
Display
MEMORY
Average
1.5V Batteries
(R6P, LR6 or AA)
Pressure Settings
I.H.B. Symbol
(Irregular heartbeat symbol)
Cuff Fit Error Symbol
Systolic
Pressure
Movement Error Symbol
TriCheckTM Symbol
Diastolic
Pressure
Heart Mark
WHO Classification Indicator
and Pressure Bar Indicator
Battery Indicator
Pulse Rate
AM / PM Mark
English 4
Clock Display
Symbols
Symbols that are printed on the device case and the AC adapter
Symbols
Function / Meaning
Recommended Action
Standby and Turn the device on.
Battery installation guide
Direct current
SN
2010
Serial number
Date of manufacture
Type BF: Device, cuff and tubing are
designed to provide special protection
against electrical shocks.
EC directive medical device label
WEEE label
Manufacturer
EU-representative
Refer to instruction manual/booklet
Class II device
Polarity of DC jack
Symbols that appear on the display
Symbols
Function / Meaning
Recommended Action
Appears while measurement is in progress. Measurement is in progress.
It blinks when the pulse is detected.
Remain as still as possible.
Irregular Heartbeat symbol (I.H.B.)
Appears when an irregular heartbeat
is detected.
It may light when a very slight vibration
like shivering or shaking is detected.
TriCheck mode
Takes three consecutive measurements
automatically and displays the average
values of the three measurements.
The reading may yield
an incorrect value. Take
Appears when a body or arm
another measurement.
movement is detected.
Remain still during
measurement.
English 5
Symbols
Function / Meaning
Appears during measurement when
the cuff is applied loosely.
Recommended Action
The reading may yield an
incorrect value. Apply the
cuff correctly, and take
another measurement.
Previous measurements stored in memory.
Average data
Full Battery
The battery power indicator during
measurement.
Low Battery
The battery power is low when it
blinks.
Replace all batteries with new
ones when the mark blinks.
Unstable blood pressure due to
movement during measurement.
Take another measurement.
Remain still during
measurement.
The systolic and diastolic values are
within 10 mmHg of each other.
The pressure value did not increase
during the inflation.
The cuff is not applied correctly.
PUL. DISPLAY ERROR
The pulse is not detected correctly.
Blood pressure monitor internal error
SYS.
Systolic blood pressure in mmHg
DIA.
Diastolic blood pressure in mmHg
PUL./min.
Apply the cuff correctly,
and take another
measurement.
Pulse per minute
AM
Data taken between 4:00 and 9:59
PM
Data taken between 18:00 and 1:59
Pressure settings
Indicates the pressure value
previously set by the user.
English 6
Remove the batteries and
press the START button,
and then install the batteries
again. If the error still
appears, contact the dealer.
Operation Mode
1. Normal Measurement
Press the START button. Blood pressure is measured and the data is stored
in memory. This device can store the last 90 measurements in memory.
2. Recalling the Data
Press the
or button to recall the data in
memory. The average of all measurements is
displayed, as indicated in the figure at the right.
button is pressed, the
Then, each time the
memory data is displayed as follows.
Average of all AM (morning) measurements
taken between 4:00 and 9:59.
Average of all PM (evening) measurements
taken between 18:00 and 1:59.
Most recent data (No.n, in the example,
No.35)
Last data (No.1)
For details on recalling the data, refer to
“Recalling the Memory Data”.
3. Deleting all Data Stored in Memory
Press both the
and buttons. The
mark
and the battery indicator appear. Press and hold
both the
and buttons until the illuminated
mark starts blinking to delete all data stored in
memory.
4. Measurement with the Desired Systolic Pressure
Refer to page 12 for measurement with the desired systolic pressure.
English 7
Using the Monitor
Installing / Changing the Batteries
1. Remove the battery cover.
2. Remove the used batteries and
insert new batteries into the battery
compartment as shown, taking
care that the polarities (+ and -) are
correct.
Use only R6P, LR6 or AA batteries.
3. Attach the battery cover.
Step 1
Step 3
Step 1
Step 2
CAUTION
Insert the batteries as shown in the battery compartment. If installed
incorrectly, the device will not work.
When
(LOW BATTERY mark) blinks on the display, replace all batteries
with new ones. Do not mix old and new batteries. It may shorten the battery
life, or cause the device to malfunction.
Replace the batteries two seconds or more after the device turns off.
If
(LOW BATTERY mark) appears even after the batteries are replaced, make
a blood pressure measurement. The device may then recognize the new batteries.
(LOW BATTERY mark) does not appear when the batteries are drained.
The battery life varies with the ambient temperature and may be shorter at
low temperatures.
Use the specified batteries only.
Remove the batteries if the device is not to be used for a long time.
The batteries may leak and cause a malfunction.
Air socket
Connecting the Air Hose
Insert the air connector plug into
the air socket firmly.
Air connector plug
Connecting the AC Adapter
Insert the AC adapter plug into the
DC jack.
Next, connect the AC adapter to an
electrical outlet.
Use the specified AC adapter.
(Refer to page 20.)
English 8
AC adapter plug
DC jack
Using the Monitor
Adjusting the Built-in Clock
Press
Adjust the clock prior to use.
1. Press the SET button until the year starts
blinking.
or button.
2. Select the year using the
Press the SET button to set the current year
and move to month/day selection. The date
can be set anywhere between the years 2010
and 2059.
or button.
3. Select the month using the
Press the SET button to set the current
month and move to day selection.
or button.
4. Select the day using the
Press the SET button to set the current day
and move to hour/minute selection.
or button.
5. Select the hour using the
Press the SET button to set the current hour
and move to minute selection.
or button.
6. Select the minute using the
(Press the SET button to go to the pressure
setting mode. For details, refer to page 12.)
Press the START button to turn the device off.
Year
or
Month
Day
or
or
Hour
Minute
Note: After three minutes of non-operation, the device
will turn off automatically.
When the clock has not been
Turn off
set, the clock display indicates
dashes as shown to the right.
Pressing the START
button will turn the
Holding down the
or
button
device off anytime.
will change the value continuously.
Selecting the Correct Cuff Size
or
or
Pressure
setting mode
Using the correct cuff size is important for an accurate reading. If the cuff is not
the proper size, the reading may yield an incorrect blood pressure value.
The arm size is printed on each cuff.
The arm cuff is a consumable. If it becomes worn, purchase a new one.
Arm Size
Recommended Cuff Size
Catalog Number
31 cm to 45 cm
Large adult cuff
CUF-F-LA
17 cm to 32 cm
Adult cuff
CUF-G-A
Arm size: The circumference of the biceps.
English 9
Using the Monitor
Do not roll up shirtsleeve tightly.
Applying the Arm Cuff
1. Wrap the cuff around the upper
arm, about 1-2 cm above the
inside of the elbow, as shown.
Place the cuff directly against the
skin, as clothing may cause a faint
pulse, and result in a measurement
error.
2. Constriction of the upper arm, caused
by tightly rolling up a shirtsleeve, may
prevent accurate readings.
Cuff
1-2 cm
Air Hose
Artery position mark
Secure the fabric fastener
firmly.
Symbols that are printed on the cuff
Symbols Function/Meaning
Recommended Action
mark on the artery of the upper arm or
Set the
Artery Position Mark in line with the ring finger on the inside of the arm.
REF
Catalog Number
Lot Number
How to Take Accurate Measurements
For the most accurate blood pressure measurement:
Sit comfortably on a chair. Rest your arm on the table. Do not cross your
legs. Keep your feet on the floor and straighten your back.
Relax for about five to ten minutes before measurement.
Place the center of the cuff at the same level as your heart.
Remain still and keep quiet during measurement.
Do not measure immediately after physical exercise or a bath. Rest for
twenty or thirty minutes before taking the measurement.
Try to measure your blood pressure at the same time every day.
Measurement
During measurement, it is normal for the cuff to feel very tight. (Do not be
alarmed).
After Measurement
After measurement, press the START button to turn the device off. After one
minute of non-operation, the device will turn off automatically.
Remove the cuff and record your data.
Note: Allow at least three minutes between measurements on the same person.
English 10
Measurements
Before measurement, read “Notes for Accurate Measurement” on page 13.
Normal Measurement
1.
Place the cuff on the arm (preferably the left arm).
Sit quietly during measurement.
2.
Press the START button.
Press
All of the display segments are displayed.
Zero (0) is displayed blinking briefly.
The display changes, as indicated in the
All of the display
figure at the right, as the measurement segments displayed
begins. The cuff starts to inflate. It is normal
for the cuff to feel very tight. A pressure bar
indicator is displayed, on the left edge of the
display, during the inflation.
Zero display
Note: If you wish to stop inflation at any time,
Starts inflation
press the START button again.
3.
When inflation is complete, deflation starts
automatically and
(heart mark) blinks,
indicating that the measurement is in
progress. Once the pulse is detected, the
mark blinks with each pulse beat.
Note: If an appropriate pressure is not obtained, the
device starts to inflate again automatically.
To
avoid
re-inflation,
see
“Measurement with the SET
Pressure” on the next page.
4.
When the measurement is complete, the
systolic and diastolic pressure readings
and pulse rate are displayed.
The cuff exhausts the remaining air and
deflates completely.
5.
Press the START button to turn the device off.
After one minute of non-operation,
the device will turn off automatically.
Note: Allow at least three minutes between
measurements on the same person.
English 11
At heart level
START
Pressurizing
Measurement
in progress
Systolic pressure
Diastolic pressure
WHO classification
Pulse rate
Exhausts remaining
air automatically
Measurements
Model UA-1020 is designed to detect the pulse and to inflate the cuff to a
systolic pressure level automatically.
If re-inflation occurs repeatedly, use the following methods.
Measurement with the SET Pressure
During the blood pressure measurement, re-inflation may occur.
A fixed pressure value can be set to avoid re-inflation.
1.
2.
At step 6 of the clock adjustment procedure
(see page 9), press the SET button to go to
the pressure setting mode. The current
setting blinks.
or
Press the
or
button to select a pressure
value about 30 mmHg or more above your
expected systolic pressure from the following.
AUTO : Automatic pressurization (default value)
180 : Pressure value of 180 mmHg (fixed)
210 : Pressure value of 210 mmHg (fixed)
Turn off
240 : Pressure value of 240 mmHg (fixed)
3.
TriCheck
setting mode
Press the SET button to go to the TriCheck setting mode.
Press the START button to turn the device off. After three minutes of
non-operation, the device will turn off automatically.
The next measurement will be performed with the new pressure value.
Measurement with the Desired Systolic Pressure
Use this method when re-inflation occurs repeatedly even if the pressure value
is set to 240 in the procedure above or when the results are not displayed
even if the pressure decreases to 20 mmHg or less.
1.
Place the cuff on the arm (preferably the left arm). At heart level
2.
Press and hold the START button until a
number about 30 to 40 mmHg higher
than your expected systolic pressure
appears.
3.
When the desired number is reached,
release the START button to start
measurement. Continue to measure
your blood pressure as described on
the previous page.
English 12
Press and hold the button
START
Release the button
at the desired
systolic pressure
Refer to the previous page
for measurement
Notes for Accurate Measurement
Sit down in a comfortable position. Place your arm on a table with your
palm facing upward and the cuff at the same level as your heart.
Relax for about five to ten minutes before taking a measurement. If you
are excited or depressed by emotional stress, the measurement will
reflect this stress as a higher (or lower) than normal blood pressure
reading and the pulse reading will usually be faster than normal.
An individual's blood pressure varies constantly, depending on what you
are doing and what you have eaten. What you drink can have a very
strong and rapid effect on your blood pressure.
This device bases its measurements on the heartbeat. If you have a very
weak or irregular heartbeat, the device may have difficulty determining
your blood pressure.
Should the device detect a condition that is abnormal, it will stop the
measurement and display an error symbol. Refer to page 6 for the
description of symbols.
This blood pressure monitor is intended for use by adults only. Consult
with your physician before using this device on a child. A child should not
use this device unattended.
TriCheck Measurement
The TriCheck mode takes three consecutive measurements automatically
and displays the average values of the three measurements.
Selecting the TriCheck Mode
In the pressure setting mode,
1.
In the pressure setting mode, press
the SET button to enter the TriCheck
setting mode. The current setting
blinks.
2.
Press the
or
button to turn the
TriCheck mode ON or OFF.
The current setting blinks
ON: TriCheck mode
OFF: Normal measurement mode (default value)
or
3.
Press the START or SET button to
turn the device off. After three
minutes of non-operation, the device
will turn off automatically.
English 13
press
Change the setting
or
START
Measurement Using the TriCheck Mode
1.
2.
Press the START button.
All of the display segments are
displayed.
Zero (0) is displayed blinking briefly
and the first measurement starts.
When the measurement is complete,
the systolic and diastolic pressure
readings and pulse rate are displayed,
then a one-minute countdown starts for
the second measurement.
3.
After one minute, the second
measurement starts.
4.
When the measurement is complete,
the average readings of the first and
second measurements are displayed,
then a one-minute countdown starts for
the third measurement.
5.
6.
At heart level
START
Press
All of the display
segments displayed
First measurement
One minute after
After one minute, the third
measurement starts.
Results of the
first measurement
Second measurement
When the measurement is complete,
the average readings of the three
measurements are displayed and
stored in memory.
Notes:
During the measurement, the
TriCheck symbol is displayed.
To cancel the measurement, press
the START button. In this case, no
data is stored in memory.
When the cuff fit error symbol appears
during the first measurement, cancel
the measurement, reapply the cuff
correctly and start a new measurement.
After measurement, the average
data of the three measurements is
stored in memory.
No data will be stored, when
canceling
the
measurements,
before completion of the third
measurement.
English 14
One minute after
Average of the first and
second measurements
Third measurement
Average of the
three measurements
Recalling the Memory Data
Note: This device stores the last 90 measurements in memory.
or button.
1. Press the
The average of all measurements and
the number of data are displayed.
(If no data, “0” is displayed. Press the
, or START button to turn the
device off.)
Press
2. Each time the
button (or the
button to display the data in the
reverse order) is pressed, the memory
data is displayed as follows.
Average of all AM (morning) measurements
taken between 4:00 and 9:59.
(In the example, 10 measurements. If
no data, “--” is displayed.)
or
Average systolic
Average diastolic
Average pulse
Average of
all the data
Average
of AM data
Average of all PM (evening) measurements
taken between 18:00 and 1:59.
(In the example, 9 measurements. If
no data, “--” is displayed.)
Most recent data (No.n, in the
example, No.35)
Three seconds after the data number
display, the measurement data is displayed.
Last data (No.1)
Three seconds after the data number
display, the measurement data is
displayed.
Average systolic
Average diastolic
Average pulse
Average systolic
Average diastolic
Average pulse
Average
of PM data
Systolic
Diastolic
Pulse
Most recent data
3. After the last data is displayed, press
the
button to return the average
display of all measurements.
4. Press the START button to turn the
device off. After one minute of
non-operation, the device will turn off
automatically.
English 15
Systolic
Diastolic
Pulse
Last data (Oldest)
What is an Irregular Heartbeat
The UA-1020 blood pressure monitor provides a blood pressure and
pulse rate measurement even when an irregular heartbeat occurs. An
irregular heartbeat is defined as a heartbeat that varies by 25% from the
average of all heartbeats during the blood pressure measurement. It is
important that you are relaxed, remain still and do not talk during
measurements.
Note: We recommend contacting your physician if you see this
symbol frequently.
Pressure Bar Indicator
The indicator monitors the progress of pressure during measurement.
Pressurizing
Releasing air
Inflation in progress
Measurement in progress
Inflation complete
WHO Classification Indicator
Each segment of the bar indicator
corresponds to the WHO blood pressure
classification described on the next page.
WHO Classification Indicator
Severe hypertension
Moderate hypertension
Mild hypertension
High normal
Normal
Optimal
Example:
Moderate hypertension
Mild hypertension
: The indicator displays a segment, based
on the current data, corresponding to the
WHO classification.
High normal
English 16
About Blood Pressure
What is Blood Pressure?
Blood pressure is the force exerted by blood against the walls of the arteries.
Systolic pressure occurs when the heart contracts. Diastolic pressure occurs
when the heart expands. Blood pressure is measured in millimeters of
mercury (mmHg). One's natural blood pressure is represented by the
fundamental pressure, which is measured first thing in the morning while one
is still at rest and before eating.
What is Hypertension and How is it Controlled?
Hypertension, an abnormally high arterial blood pressure, if left unattended,
can cause many health problems including stroke and heart attack.
Hypertension can be controlled by altering lifestyle, avoiding stress, and with
medication under a doctor’s supervision.
To prevent hypertension or keep it under control:
Do not smoke
Exercise regularly
Reduce salt and fat intake
Have regular physical checkups
Maintain proper weight
Why Measure Blood Pressure at Home?
Blood pressure measured at a clinic or doctor's office may cause
apprehension and can produce an elevated reading, 25 to 30 mmHg higher
than that measured at home. Home measurement reduces the effects of
outside influences on blood pressure readings, supplements the doctor's
readings and provides a more accurate, complete blood pressure history.
WHO Blood Pressure Classification
Standards to assess high
blood
pressure,
without
regard to age, have been
established by the World
Health Organization (WHO),
as shown in the chart.
Blood Pressure Variations
An individual’s blood pressure
varies greatly on a daily and
seasonal basis. It may vary by
30 to 50 mmHg due to various conditions during the day. In hypertensive
individuals, variations are even more pronounced. Normally, the blood
pressure rises while at work or play and falls to its lowest levels during sleep.
So, do not be overly concerned by the results of one measurement.
Take measurements at the same time every day using the procedure
English 17
described in this manual to get to know
your normal blood pressure. Regular
readings give a more comprehensive blood
pressure history. Be sure to note the date
and time when recording your blood
pressure. Consult your doctor to interpret
your blood pressure data.
Troubleshooting
Problem
Possible Reason
Nothing
Batteries are drained.
appears on the
display, even
Battery terminals are not
when the power in the correct position.
is turned on.
Battery voltage is too low.
(LOW BATTERY mark)
The cuff does
blinks. If the batteries are
not inflate.
drained completely, the
mark does not appear.
The cuff is not applied
properly.
You moved your arm or
body during
The device does measurement.
not measure.
Readings are
The cuff position is not
too high or too correct.
low.
Other
The value is different
from that measured at a
clinic or doctor’s office.
Recommended Action
Replace all batteries with new ones.
Reinstall the batteries with
negative and positive terminals
matching those indicated on the
battery compartment.
Replace all batteries with new
ones.
Apply the cuff correctly.
Make sure you remain still and
quiet during measurement.
Sit comfortably and still.
Place your arm on a table with your
palm facing upward and the cuff at
the same level as your heart.
If you have a very weak or
irregular heat beat, the device
may have difficulty in determining
your blood pressure.
Refer to “Why Measure Blood
Pressure at Home?”.
Remove the batteries. Place
them back properly and take
another measurement.
Note: If the actions described above do not solve the problem, contact the
dealer. Do not attempt to open or repair this product, as any attempt to
do so will make your warranty invalid.
English 18
Maintenance
Do not open the device. It uses delicate electrical components and an
intricate air unit that could be damaged. If you cannot fix the problem using
the troubleshooting instructions, contact the authorized dealer in your area
or our customer service department. The A&D customer service will
provide technical information, spare parts and units to authorized dealers.
The device was designed and manufactured for a long service life.
However it is generally recommended to have the device inspected every
2 years, to ensure proper functioning and accuracy. Please contact the
authorized dealer in your area or A&D for maintenance.
Technical Data
Type
UA-1020
Measurement method
Oscillometric measurement
Measurement range
Pressure: 0 - 299 mmHg
Systolic pressure: 60 - 279 mmHg
Diastolic pressure: 40 - 200 mmHg
Pulse:
40 - 180 beats / minute
Measurement accuracy
Pressure: ±3 mmHg
Pulse:
±5%
Power supply
4 x 1.5V batteries (R6P, LR6 or AA) or
AC adapter (TB-233) (Not included)
Number of measurements
Approx. 1000 measurements, when AA alkaline
batteries are used, with pressure value of 180
mmHg at room temperature of 23°C
Classification
Internally powered ME equipment (Supplied by
batteries) /
Class II (Supplied by adapter)
Continuous operation mode
Clinical test
According to ANSI / AAMI SP-10 1992
EMC
IEC 60601-1-2: 2007
Memory
Last 90 measurements
Operating condition
+10°C to +40°C / 15%RH to 85%RH
800 hPa to 1060 hPa
Transport / Storage conditions -20°C to +60°C / 10%RH to 95%RH
Dimensions
Approx. 140 [W] x 60 [H] x 105 [D] mm
English 19
Weight
Approx. 285 g, excluding the batteries
Applied part
Cuff
Useful life
Device: 5 years (when used six times a day)
Cuff: 2 years (when used six times a day)
Accessory AC adapter
The adapter is to connect the blood pressure
monitor to a power source at home.
TB-233
Please contact your local A&D dealer for
purchasing.
The AC adapter is required to be inspected or
replaced periodically.
TB-233C
Type BF
Input: 100-240V
Output: 6V
139°C
TB-233BF
Input: 240V
Output: 6V
500mA
2A
500mA
139°C
2A
Accessories sold separately
Cuff
Catalog Number
CUF-F-LA
CUF-G-A
Cuff Size
Arm Size
Large adult cuff 31 cm to 45 cm
Adult cuff
17 cm to 32 cm
AC adapter
Catalog Number
TB-233C
TB-233BF
Plug
Type C
Type BF
Note: Specifications are subject to change without prior notice.
EMC table information is listed on our website:
http://www.aandd.jp/products/manual/medical/emc_acadapter_en.pdf
English 20
Asahi 1-243, Kitamoto-shi, Saitama 364-8585, JAPAN
Telephone: [81] (48) 593-1111
Fax: [81] (48) 593-1119
A&D INSTRUMENTS LIMITED
Unit 24/26 Blacklands Way, Abingdon Business Park, Abingdon, Oxfordshire
OX14 1DY United Kingdom
Telephone: [44] (1235) 550420
Fax: [44] (1235) 550485
A&D ENGINEERING, INC.
1756 Automation Parkway, San Jose, California 95131, U.S.A.
Telephone: [1] (408) 263-5333
Fax: [1] (408)263-0119
A&D AUSTRALASIA PTY LTD
32 Dew Street, Thebarton, South Australia 5031, AUSTRALIA
Telephone: [61] (8) 8301-8100
Fax: [61] (8) 8352-7409
Download PDF