Cobalt Digital 9001 3G/HD/SD 1x9 Reclocking Distribution Amplifier Product manual

Cobalt Digital Inc.
9001
3G/HD/SD SDI
Reclocking Distribution Amplifier
Owner’s Manual
9001-OM
Version: 1.8
9001 • 3G/HD/SD SDI Reclocking Distribution Amplifier Owner’s Manual
•
•
•
•
•
Cobalt Part Number: 9001-OM
Document Version: 1.8
Printed in the United States.
Last Author: CGG
Release Date: 8/26/2013
The information contained in this Owner’s Manual is subject to change without notice or obligation.
Copyright
© 2013 Cobalt Digital Inc. All rights reserved.
Contents of this publication may not be reproduced in any form without the written permission of
Cobalt Digital Inc. Reproduction or reverse engineering of copyrighted software is prohibited.
Notice
The material in this manual is furnished for informational use only. It is subject to change without
notice and should not be construed as a commitment by Cobalt Digital Inc. Cobalt Digital Inc assumes
no responsibility or liability for errors or inaccuracies that may appear in this manual.
Trademarks
Page 2
•
openGear® is a registered trademark of Ross Video Limited.
•
•
is a registered trademark of Cobalt Digital Inc.
All other product names and any registered and unregistered trademarks mentioned in this
manual are used for identification purposes only and remain the exclusive property of
their respective owners.
9001 Owner’s Manual • (V 1.8)
Important Regulatory and Safety Notices
Before using this product and any associated equipment, refer to the “Important Safety Instructions”
listed below so as to avoid personnel injury and to prevent product damage.
Products may require specific equipment, and /or installation procedures be carried out to satisfy
certain regulatory compliance requirements. Notices have been included in this publication to call
attention to these specific requirements.
Symbol Meanings
This symbol on the equipment refers you to important operating and maintenance
(servicing) instructions within the Product Manual Documentation. Failure to heed
this information may present a major risk of damage or injury to persons or
equipment.
The symbol with the word “Warning” within the equipment manual indicates a
potentially hazardous situation, which if not avoided, could result in death or serious
injury.
Warning
The symbol with the word “Caution” within the equipment manual indicates a
potentially hazardous situation, which if not avoided, may result in minor or
moderate injury. It may also be used to alert against unsafe practices.
Caution
The symbol with the word “Notice” within the equipment manual indicates a
situation, which if not avoided, may result in major or minor equipment damage or a
situation which could place the equipment in a non-compliant operating state.
Notice
This symbol is used to alert the user that an electrical or electronic device or
assembly is susceptible to damage from an ESD event.
ESD
Susceptibility
Important Safety Instructions
Caution
This product is intended to be a component product of the openGear® frame. Refer to
the openGear® frame Owner’s Manual for important safety instructions regarding the
proper installation and safe operation of the frame as well as it’s component
products.
Warning
Certain parts of this equipment namely the power supply area still present a safety
hazard, with the power switch in the OFF position. To avoid electrical shock,
disconnect all A/C power cords from the chassis' rear appliance connectors before
servicing this area.
Warning
Service barriers within this product are intended to protect the operator and service
personnel from hazardous voltages. For continued safety, replace all barriers after
any servicing.
This product contains safety critical parts, which if incorrectly replaced may present
a risk of fire or electrical shock. Components contained within the product’s power
supplies and power supply area, are not intended to be customer serviced and should
be returned to the factory for repair.
To reduce the risk of fire, replacement fuses must be the same type and rating.
Only use attachments/accessories specified by the manufacturer.
9001 Owner’s Manual • (V 1.8)
Page 3
Environmental Information
The equipment that you purchased required the extraction and use of natural resources for its
production. It may contain hazardous substances that could impact health and the environment.
To avoid the potential release of those substances into the environment and to diminish the need for the
extraction of natural resources, Cobalt Digital encourages you to use the appropriate take-back systems.
These systems will reuse or recycle most of the materials from your end-of-life equipment in an
environmentally friendly and health conscious manner.
The crossed-out wheeled bin symbol invites you to use these systems.
If you need more information on the collection, reuse, and recycling systems, please contact your local
or regional waste administration.
You can also contact Cobalt Digital for more information on the environmental performances of our
products.
Page 4
9001 Owner’s Manual • (V 1.8)
Contents
Introduction
6
In This Chapter .......................................................................................................................... 6
A Word of Thanks ..................................................................................................................... 6
Overview.................................................................................................................................... 6
Functional Block Diagram ......................................................................................................... 7
Supported Serial Rates............................................................................................................... 7
Documentation Terms................................................................................................................ 7
Installation and Setup
8
In This Chapter .......................................................................................................................... 8
Static Discharge ......................................................................................................................... 8
Unpacking.................................................................................................................................. 8
Rear Module Installation (Optional) .......................................................................................... 9
Board Installation..................................................................................................................... 10
Cable Connections ................................................................................................................... 11
Card Control and Status ........................................................................................................... 12
Card Status ................................................................................................................ 12
Switches..................................................................................................................... 12
Remote Control
13
In This Chapter ........................................................................................................................ 13
DashBoard Control System Software ...................................................................................... 13
Service Information
15
In This Chapter ........................................................................................................................ 16
Troubleshooting Checklist ....................................................................................................... 16
Warranty and Repair Policy..................................................................................................... 17
Ordering Information
19
9001 and Related Products ...................................................................................................... 19
Contact Us
20
Contact Cobalt Digital Inc. ...................................................................................................... 20
Visit us at the Cobalt Digital Inc. website................................................................................ 20
9001 Owner’s Manual • (V 1.8)
Page 5
Introduction
In This Chapter
This chapter includes the following sections:
•
A Word of Thanks
•
Overview
•
Functional Block Diagram
•
Supported Audio and Video Formats
•
Documentation Terms
A Word of Thanks
Congratulations on choosing the openGear® 9001 3G/HD/SD Reclocking Distribution Amplifier. The
9001 is part of a full line of modular conversion gear for broadcast TV environments. The Cobalt
Digital line includes video decoders and encoders, audio embeders and de-embeders, distribution
amplifiers, format converters, and much more. Cobalt modular conversion gear will meet your signal
conversion and distribution needs now and well into the future.
Should you have questions pertaining to the installation or operation of your 9001, please contact us at
the numbers listed on the back cover of this manual. We are happy to help with any questions regarding
this or any other of our cards.
Overview
The 9001 is a high quality 3G/HD/SD Reclocking Distribution Amplifier. It is capable of equalizing
and reclocking an SDI signal in 3G, HD, or SD.
The 9001 can equalize and reclock an incoming SDI signal using up to 300m of cable at 270Mbps, up
to 120m of cable at 1.485Gbps, and 80m at 3Gbps.
The thin profile and low power consumption of the 9001 allows twenty of the 9001 cards to be
installed in a single 20-slot frame (when used in conjunction with a 9001 split rear module).
Page 6
9001 Owner’s Manual • (V 1.8)
Functional Block Diagram
Supported Serial Rates
The 9001 will reclock 270 Mbps, 1.485 Gbps, and 3 Gbps signals. Signals of other rates will be
equalized and distributed to the outputs, and the reclocker will be bypassed.
Documentation Terms
The following terms are used throughout this guide:
•
“Frame” refers to the HPF-9000 or 8321 frame that houses the 9001 card.
•
“Operator” and “User” both refer to the person who uses the 9001.
•
“Board” and “Card” all refer to the 9001 card itself, including all components and
switches.
•
“System” and “Video system” refers to the mix of interconnected production and
terminal equipment in which the 9001 operates.
9001 Owner’s Manual • (V 1.8)
Page 7
Installation and Setup
In This Chapter
This chapter includes the following sections:
•
Static Discharge
•
Unpacking
•
Rear Module Installation (Optional)
•
Board Installation
•
BNC Connections
•
Menu Structure
•
Factory Defaults
Static Discharge
Whenever handling the card and other related equipment, please observe all static discharge
precautions as described in the following note:
Static discharge can cause serious damage to sensitive
semiconductor devices. Avoid handling circuit boards in high
static environments such as carpeted areas, and when wearing
synthetic fiber clothing. Always exercise proper grounding
precautions when working on circuit boards and related
equipment.
ESD
Susceptibility
Unpacking
Unpack each card you received from the shipping container, and check the contents against the packing
list to ensure that all items are included. If any items are missing or damaged, contact your sales
representative or Cobalt Digital directly.
Page 8
9001 Owner’s Manual • (V 1.8)
Rear Module Installation
If you are installing the card into a slot with no rear module, you should have ordered and received a
Rear Module with your card. You will need to install it in the 20-slot frame before you can connect
cables.
Use the following steps to install the rear module in a 20-slot frame:
1.
On the rear of the frame, locate the card frame slot.
2.
As shown in Figure 2, seat the bottom of the rear module in the seating slot at the
base of the frame’s back plane.
Figure 2. Rear Module Installation
3.
Align the top hole of the rear module with the screw hole on the top edge of the
frame back plane.
4.
Using a Phillips driver and the supplied screw, fasten the REAR MODULE panel to
the frame back plane. Do not over tighten.
This completes the procedure for installing the rear module in a 20-slot frame.
9001 Owner’s Manual • (V 1.8)
Page 9
Board Installation
Use the following steps to install the card in the frame:
1.
Warning
Refer to the frame product manual to ensure that the frame is properly installed
according to instructions.
Heat and power distribution requirements within a frame may dictate
specific slot placement of cards. Cards with many heat-producing
components should be arranged to avoid areas of excess heat build-up,
particularly in frames using convection cooling.
Note: This card is default set with remote control set to disabled. If DashBoard or a Cobalt
Remote Panel is to be used with card, enable remote control on card as described in Card Control and
Status on the next page before installing card.
2.
After selecting the desired frame installation slot, hold the card by the edges and
carefully align the card edges with the slots in the frame. Then, fully insert the card
into the frame until the rear connection plugs are properly seated on the midplane and
rear modules.
This completes the procedure for installing the card in the frame.
Page 10
9001 Owner’s Manual • (V 1.8)
Cable Connections
This section provides instructions for connecting cables to 9001 rear modules. Connect the input and
output cables according to the following diagram. Split rear module RM20-9001-A/S and RM20-9001B/S allow two cards to be installed in adjacent slots. B/S versions are available in DIN1.0/2/3 and
HDBNC versions.
RM20-9001-A
RM20-9001-A/S
RM20-9001-B/S
Note: Early versions of 9001 have some outputs as inverting. These outputs are not compatible with
ASI video. Please contact product support and have card serial number on hand for more information.
Figure 3. Connector Designations for the Card Rear Modules
9001 Owner’s Manual • (V 1.8)
Page 11
Card Control and Status
Card Status
The card has an LED that indicates whether Dashboard remote control is enabled, or if the switch bank
controls the card. See description of switch 1 below.
The card also indicates the status of each of the outputs signal with the three banks of four LEDs
labeled with the different supported formats (1080, 720, 625, 525). When the card has locked to a
particular output format, that LED will be illuminated. When the card has not locked to a particular
video format, the card will search all possible formats, and the lights will cycle rapidly.
Switches
There is a bank of eight switches (S1) on the front edge that controls the card.
Segment
1
2
3
4
ON
ON
ON OFF
OFF ON
OFF OFF
5-8
Function
Up – Remote control Enabled*
Down – Remote Control Disabled
Up – Reclocking control Enabled*
Down – Reclocking Control Disabled
Selects Output Rate
Automatic rate determination
2.967/2.970 Gbps
1.4835/1.485 Gbps
270 Mbps
Switch 5-8 are reserved
* Switch 1 controls the behavior of the rest of the switches. With switch 1 set in the up position,
Dashboard remote control software can change the settings of the card. Consequently the rest of the
onboard switches will have no effect. With switch 1 set in the down position, Dashboard remote control
software is prevented from making changes to the card settings. Consequently the onboard switches 2-4
control the settings.
The factory default settings are as follows
1) Remote Control is disabled.
2) Rate is set to Auto.
Note: This card is default set with remote control set to disabled. If DashBoard or a Cobalt
Remote Panel is to be used with card, enable remote control on card before installing card.
Page 12
9001 Owner’s Manual • (V 1.8)
Remote Control
In This Chapter
This section provides a detailed explanation on using remote control functions with your card.
DashBoard Control System Software
The DashBoard Control System enables you to monitor and control openGear® frames and controller
cards from a computer. The DashBoard software and manual can be downloaded from the Cobalt
Digital Inc. website.
Using the Menus
You must first install the DashBoard Control System software on your computer. Refer to the
DashBoard User Manual for software installation procedures and for using the DashBoard interface.
9001 Owner’s Manual • (V 1.8)
Page 13
The Menu System
The following table and sections describe the menus, items, and parameters available from the
DashBoard Control System software for the card.
Table 3. DashBoard Menus
Menu
Item
Parameters
Product
CDI-9001
Manufacturer
Cobalt Digital Inc.
############
Displays the Silicon Serial
Number of the card.
Software Release
Number
###
The release number of the
firmware in this card
Software Build
Date
###
The internal build number
of this software
Serial Number
Card Info
(Read-only)
Temperature
Temperature of on card
sensor
Input Current
Current consumed from
+12V rail
Input Voltage
Measured voltage of +12V
rail
Remote Control
Enabled/Disabled
Automatic
Control
Rate
2.967/2970 Gbps
1.4835/1.485Gbps
270 Mbps
Reclocker
Lock Status
Page 14
Description
On/Off
This shows whether the
remote is enabled (S1-1 on
the board is up)
This forces the reclocker to
only run at the specified
rate. “Automatic” means
the reclocker will detect
the input rate and reclock
it.
Enables or Disables
Reclocking on all outputs.
Describes the current input
rate
9001 Owner’s Manual • (V 1.8)
Specifications
Technical Specifications
Table 4. Card - Technical Specifications
Category
Parameter
Serial Digital
Video Inputs
Serial Digital
Video Outputs
Specification
Number of Inputs
1
Data Rates Supported
SMPTE 424M, 292M, and 259M
Equalization (Belden 1694A)
3G: 80 m
HD: 150m
SD: 350 m
Return Loss
>15dB at 5 MHz – 1.485 GHz
>10 dB at 1.5 GHz - 3.0 GHz
Number of Outputs
9 Outputs:
4: SDI Reclocked copies of the input signal
4: User configurable SD-SDI/Analog composite
Impedance
75 Ω
Return Loss reclocked DA output
>15dB at 5 MHz – 1.485 GHz
>10 dB at 1.5 GHz - 3.0 GHz
Signal Level
800 mV nominal
Jitter (wideband)
HD: < 0.2 UI
Total Power Consumption
2 Watts
Specifications are subject to change without notice.
9001 Owner’s Manual • (V 1.8)
Page 15
Service Information
In This Chapter
This chapter includes the following sections:
•
Troubleshooting Checklist
•
Warranty and Repair Policy
Troubleshooting Checklist
Routine maintenance to this openGear® product is not required. In the event of problems with your
card, the following basic troubleshooting checklist may help identify the source of the problem. If the
module still does not appear to be working properly after checking all possible causes, please contact
your openGear® products distributor, or the Technical Support department at the numbers listed under
the “Contact Us” section at the end of this manual.
Page 16
1.
Visual Review  Performing a quick visual check may reveal many problems, such
as connectors not properly seated or loose cables. Check the module, the frame, and
any associated peripheral equipment for signs of trouble.
2.
Power Check  Check the power indicator LED on the distribution frame front
panel for the presence of power. If the power LED is not illuminated, verify that the
power cable is connected to a power source and that power is available at the power
main. Confirm that the power supplies are fully seated in their slots. If the power
LED is still not illuminated, replace the power supply with one that is verified to
work.
3.
Reseat the Card in the Frame  Eject the card and reinsert it in the frame.
4.
Check Control Settings  Refer to the Installation and Operation sections of the
manual and verify all user-adjustable component settings.
5.
Input Signal Status  Verify that source equipment is operating correctly and that a
valid signal is being supplied.
6.
Output Signal Path  Verify that destination equipment is operating correctly and
receiving a valid signal.
7.
Module Exchange  Exchanging a suspect module with a module that is known to
be working correctly is an efficient method for localizing problems to indivitriple
modules.
9001 Owner’s Manual • (V 1.8)
Warranty and Repair Policy
Cobalt Digital Inc. Limited Warranty
This product is warranted to be free from defects in material and workmanship for a period of five (5)
years from the date of shipment to the original purchaser, except that 4000, 5000, 6000, 8000 series
power supplies, and Dolby® modules (where applicable) are warranted to be free from defects in
material and workmanship for a period of one (1) year.
Cobalt Digital Inc.'s (“Cobalt”) sole obligation under this warranty shall be limited to, at its option, (i)
the repair or (ii) replacement of the product, and the determination of whether a defect is covered under
this limited warranty shall be made at the sole discretion of Cobalt.
This limited warranty applies only to the original end-purchaser of the product, and is not assignable or
transferrable therefrom. This warranty is limited to defects in material and workmanship, and shall not
apply to acts of God, accidents, or negligence on behalf of the purchaser, and shall be voided upon the
misuse, abuse, alteration, or modification of the product. Only Cobalt authorized factory
representatives are authorized to make repairs to the product, and any unauthorized attempt to repair
this product shall immediately void the warranty. Please contact Cobalt Technical Support for more
information.
To facilitate the resolution of warranty related issues, Cobalt recommends registering the product by
completing and returning a product registration form. In the event of a warrantable defect, the
purchaser shall notify Cobalt with a description of the problem, and Cobalt shall provide the purchaser
with a Return Material Authorization (“RMA”). For return, defective products should be double boxed,
and sufficiently protected, in the original packaging, or equivalent, and shipped to the Cobalt Factory
Service Center, postage prepaid and insured for the purchase price. The purchaser should include the
RMA number, description of the problem encountered, date purchased, name of dealer purchased from,
and serial number with the shipment.
Cobalt Digital Inc. Factory Service Center
2406 E. University Avenue
Office: (217) 344-1243
Urbana, IL 61802 USA
Fax:
www.cobaltdigital.com
Email: [email protected]
(217) 344-1245
THIS LIMITED WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES
EXPRESSED OR IMPLIED, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND
FITNESS FOR A PARTICULAR PURPOSE AND OF ALL OTHER OBLIGATIONS OR
LIABILITIES ON COBALT'S PART. ANY SOFTWARE PROVIDED WITH, OR FOR USE WITH,
THE PRODUCT IS PROVIDED “AS IS.” THE BUYER OF THE PRODUCT ACKNOWLEDGES
THAT NO OTHER REPRESENTATIONS WERE MADE OR RELIED UPON WITH RESPECT TO
THE QUALITY AND FUNCTION OF THE GOODS HEREIN SOLD. COBALT PRODUCTS ARE
NOT AUTHORIZED FOR USE IN LIFE SUPPORT APPLICATIONS.
COBALT'S LIABILITY, WHETHER IN CONTRACT, TORT, WARRANTY, OR OTHERWISE, IS
LIMITED TO THE REPAIR OR REPLACEMENT, AT ITS OPTION, OF ANY DEFECTIVE
PRODUCT, AND SHALL IN NO EVENT INCLUDE SPECIAL, INDIRECT, INCIDENTAL, OR
CONSEQUENTIAL DAMAGES (INCLUDING LOST PROFITS), EVEN IF IT HAS BEEN
ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
9001 Owner’s Manual • (V 1.8)
Page 17
In Case of Problems
Should any problem arise with your openGear® card, please contact the Cobalt Digital Inc. Technical
Support Department. (Contact information is supplied at the end of this publication.)
A Return Material Authorization number (RMA) will be issued to you, as well as specific shipping
instructions, should you wish our factory to repair your openGear® card. If required, a temporary
replacement module will be made available at a nominal charge. Any shipping costs incurred will be
the responsibility of you, the customer. All products shipped to you from Cobalt Digital Inc. will be
shipped collect.
The Cobalt Digital Inc. Technical Support Department will continue to provide advice on any product
manufactured by Cobalt Digital Inc., beyond the warranty period without charge, for the life of the
equipment.
Page 18
9001 Owner’s Manual • (V 1.8)
Ordering Information
9001 and Related Products
Your 9001 3G/HD/SD SDI Reclocking Distribution Amplifier is a part of the openGear® family of
products. Cobalt Digital offers a full line of openGear® terminal equipment including distribution,
conversion, monitoring, synchronizers, encoders, decoders, embedders, and de-embedders, as well as
analog audio and video products.
Standard Equipment
•
9001 3G/HD/SD SDI Reclocking Distribution Amplifier
•
9001-OM 3G/HD/SD SDI Reclocking Distribution Amplifier Owner’s Manual
Optional Equipment
•
9001-OM 3G/HD/SD SDI Reclocking Distribution Amplifier Owner’s Manual
(additional Owner’s Manual)
ƒ
RM20-9001-A 20-Slot Frame Rear I/O Module (Standard Width) HD/SD-SDI Input
BNC, 9 Reclocked HD/SD-SDI Output BNCs
ƒ
RM20-9001-A/S 20-Slot Frame Rear I/O Module (Split) HD/SD-SDI Input BNC, 4
Reclocked HD/SD-SDI Output BNCs (per card)
ƒ
RM20-9001-B/S-HDBNC 20-Slot Frame Rear I/O Module (Split High-Density) HD/SDSDI Input, 1x9 HD/SD-SDI Outputs (per card; all connectors HDBNC)
•
RM20-9001-B/S-DIN 20-Slot Frame Rear I/O Module (Split High-Density) HD/SD-SDI
Input, 1x9 HD/SD-SDI Outputs (per card; all connectors DIN 1.0/2.3)
•
HPF-9000-CN High-Power 20-Slot Frame; 2RU with fans, cover plates for unused slots.
Includes one PSU-9000 Power Supply Module and MFC-8320-N Network Controller
Card.
•
OG3-FR 20-Slot Frame and Power Supply with Cooling Fans
(2RU, holds 20 cards maximum)
9001 Owner’s Manual • (V 1.8)
Page 19
Contact Us
Contact Cobalt Digital Inc.
PHONE
E-MAIL
POSTAL
SERVICE
General Business Office
and Technical Support
217.344.1243
Fax
217.344.1245
General Information
[email protected]
Sales Information
[email protected]
Cobalt Digital Inc.
2406 East University Avenue
Urbana, IL 61802 USA
Visit us at the Cobalt Digital Inc. website.
http://www.cobaltdigital.com
Page 20
•
Online catalog
•
Related products and full product lines
•
Trade show information
•
Dealer information
•
Cobalt Digital Inc. news
9001 Owner’s Manual • (V 1.8)