Installation Care & Cleaning

Installation Care & Cleaning
Installation
Care & Cleaning
1. Make sure the bike is completely cool before starting the
installation. Make sure the bike is secure on the sidestand
or ideally a rear service stand.
12. Before you run the bike, clean off all fingerprints and dirt, as
any oily residue will etch the metal and become somewhat
permanent when the system gets hot. Run the bike and
enjoy. It is normal for some white smoke to appear the first
time you start the bike. This is packing/manufacturing oil
from inside the pipe burning off. Check for gaps or leaks.
If you find a leak, a little high temperature silicon sealant
should fix it. After 50 to 100 miles, recheck all fasteners for
tightness.
2. Remove OEM Muffler assembly. Retain mounting bolt for
later use.
2009-10 Honda
CB1000R
Care & Cleaning
Keep system free of dirt and moisture. Store in a cool, dry place. For cleaning use a mild spray cleaner. Always apply cleaner or polish with a soft,
clean cloth.
Slip-on Exhaust System with M-2 Canister
Part # 005-2840406V / 005-2840407V / 005-2840408V
3. Remove the OEM rubber grommet and sleeve from OEM
muffler mounting location. This will not be reused.
4. Remove right side rear passenger foot rest assembly.
5. Install TBR muffler mounting backet behind OEM
passenger foot rest and re-install on motorcycle.
Stainless Header System: Polished stainless steel pipes will turn a light golden hue after a few heat cycles, this is a normal characteristic of high quality
stainless steel.
Carbon Fiber Mufflers: Always make sure the fiberglass packing inside is in
good condition and not burned out, as exhaust heat inside an empty canister will
deteriorate the Carbon Fiber sleeve. TBR sells repack kits (TBR
part # 005-10038) that include new rivets and repack material as
well as a drill bit (#30), making it easy to do yourself. Also, NEVER dyno test your bike with carbon fiber mufflers installed - the
intense heat and lack of cooling air can quickly cause the CF
material to burn. Two Brothers Racing does not provide a warranty for
burned carbon fiber.
Aluminum Mufflers: Use an aluminum or mag wheel polish such as Mother’s to restore the bright finish to factory spec.
6. Attach TBR slip-tube to TBR muffler using the supplied
6x20mm bolts and lock washers. Leave loose for now.
Parts List
Qty.
Description
Part Number
1
1
1
1
2
4
4
1
1
1
1
1
Muffler Canister
Slip-On Tube
Muffler Canister Clamp
HARDWARE KIT
X-Ring (half)
6x14mm Socket Head Cap Screw
6mm Split Lock Washer
Mounting Bracket
64mm Barrel Clamp
5mm Long Handle Ball End Hex Key
T20 Torx Short Hex Key
TBR Sticker Kit
Varies
005-28404S
Varies
005-284-3
005-7-2-3
005-SH614
005-WL6
005-284-B
005-27-64MSH
005-9-18610
005-9-15820
015-10212
7. Slide barrel clamp over slip-tube joint and rubber lined
muffler clamp over muffler assembly.
IMPORTANT - PLEASE READ CAREFULLY
We recommend that this performance part be installed by a qualified motorcycle
technician. If you have any doubts as to your ability to install this performance
part, please consult with your local motorcycle dealer. Read all instructions first
before starting installation. Make sure the motorcycle and exhaust system are
completely cool before starting the installation. Also, make sure the bike is secure
on a centerstand or ideally a service lift during installation. Be sure to save all stock
components for possible use later.
**This product has not been tested with all available accessories and some
items may cause excessive heat. Excessive heat may cause damage to your
vehicle. Two Brothers Racing will not be responsible for damaged parts.
8. Install on motorcycle and attach using the OEM muffler
mounting bolt.
9. Align muffler and tighten the 4 X-ring bolts.
10. Tighten muffler clamp and barrel clamp at slip-tube joint.
11. Double check all your work.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement