Edimax | EW-7416APn | Edimax EW-7416APn Wireless Access Point Quick Install

0
Multi-Language QIG on the CD
===============================
Český: Českého průvodce rychlou instalací
naleznete na přiloženém CD s ovladači
Deutsch: Finden Sie bitte das deutsche S.A.L.
beiliegend in der Treiber CD
Español: Incluido en el CD el G.R.I. en Español.
Français: Veuillez trouver l’français G.I.R ci-joint
dans le CD
Italiano: Incluso nel CD il Q.I.G. in Italiano.
Magyar: A magyar telepítési útmutató
megtalálható a mellékelt CD-n
Nederlands: De nederlandse Q.I.G. treft u aan op
de bijgesloten CD
Polski: Skrócona instrukcja instalacji w języku
polskim znajduje się na załączonej płycie CD
Português: Incluído no CD o G.I.R. em Portugues
Русский: Найдите Q.I.G. на pусскoм языке на
приложеном CD
Türkçe: Ürün ile beraber gelen CD içinde Türkçe
Hızlı Kurulum Kılavuzu'nu bulabilirsiniz
1
Copyright© by Edimax Technology Co, LTD. all rights reserved. No
part of this publication may be reproduced, transmitted, transcribed,
stored in a retrieval system, or translated into any language or
computer language, in any form or by any means, electronic,
mechanical, magnetic, optical, chemical, manual or otherwise, without
the prior written permission of this company
This company makes no representations or warranties, either
expressed or implied, with respect to the contents hereof and
specifically disclaims any warranties, merchantability or fitness for any
particular purpose. Any software described in this manual is sold or
licensed "as is". Should the programs prove defective following their
purchase, the buyer (and not this company, its distributor, or its dealer)
assumes the entire cost of all necessary servicing, repair, and any
incidental or consequential damages resulting from any defect in the
software. Further, this company reserves the right to revise this
publication and to make changes from time to time in the contents
hereof without obligation to notify any person of such revision or
changes.
All brand and product names mentioned in this manual are trademarks
and/or registered trademarks of their respective holders.
Linux Open Source Code
Certain Edimax products include software code developed by third
parties, including software code subject to the GNU General Public
License ("GPL") or GNU Lesser General Public License ("LGPL").
Please see the GNU (www.gnu.org) and LPGL (www.gnu.org)
Web sites to view the terms of each license.
The GPL Code and LGPL Code used in Edimax products are
distributed without any warranty and are subject to the copyrights
of their authors. For details, see the GPL Code and LGPL Code
licenses. You can download the firmware-files at
http://www.edimax.com.tw under "Download" page.
2
English Version.
Getting Started
Before deploying the Access Point, please make sure all the PCs
in your wired network are able to obtain an IP address
automatically from the router like the figure below.
After the Access Point is deployed, you can surf the Internet /
Intranet wirelessly as show in the figure below.
3
Physical Description
Front Panel
The LED lights located on the Access Point’s front panel provide
information of the Access Point’s current status.
EW-7416APn
LED
PWR
(Power)
WLAN
(Wireless LAN)
Color
Status
Power is supplied.
Off
No Power.
Green
Green
Flash
Antenna is transmitting or
receiving data.
Orange
(EW-7209APg)
Off
Antenna is not transmitting
or receiving data.
On
LAN
(Link / Act)
Green
Flash
Off
Back Panel
EW-7416APn
z
Description
Lit
Antenna Connector
4
A valid link is established.
It is transmitting or receiving
data.
No link is established.
This is where you connect the antenna. It is a round connector
(standard Reverse SMA).
z
12 VDC
This is where you connect the power adapter.
z
WPS/Reset
Reset the router to factory default settings (clear all settings) or
start WPS function. Press this button and hold for 20 seconds
to clear all settings, and press this button for less than 5
seconds to start WPS function.
z
10/100M (EW-7416APn )
This LAN port is where you connect the Access Point to your
Ethernet devices (switch or router).
Wireless LAN Access Point Configuration
To configure the other advanced settings of this Access Point with
advanced setting such as data encryption, please follow the
procedures to login the Access Point’s setup page.
To configure the more advanced settings from this Access Point,
such as data-encryption, please follow the procedure to login the
Access Point’s setup page.
The IP address of the Access Point is 192.168.2.1
First, assign an IP Address to the PC
Before assigning an IP address to the PC, please connect a
network cable from the LAN port of the PC to the LAN port of the
Access Point as show below.
5
1. Click “Start” on the task bar then select the “Control Panel” to
open it.
6
2. Click “Switch to Classic View” on the top left corner to see
more setting icons…
3. Find the “Network Connection” icon then Double-Click to
open the network connection settings.
7
4. You will see the “Local Area Connection” icon, click the icon
to highlight it, then Right-Click the mouse to open the sub-menu
and select the “Properties” to setup the IP address.
z
Click and highlight the “Internet Protocol (TCP/IP)”, then click
the “Properties”
8
z
Select “Use the following IP address”. Enter a fixed IP
address, for example “192.168.2.10”, with a subnet mask of
“255.255.255.0” and leave “Default gateway”, “Preferred
DNS server” and “Alternate DNS server” blank then press
“OK” to close.
Second, login to the Access Point with a Web Browser
1. Open up web browser and type in 192.168.2.1 (Access Point
default IP address) to access the Access Point’s setup page.
2. A screen requesting user name and password, shown on next
page, will appear. The default user name and password are:
User Name: admin / Password: 1234
Note: It’s highly recommended to change the login settings and
keep it for future reference.
9
3. Enter the default user name and password, then press OK
button. You can start configuring the Access Point now.
Note: If this Access Point will be connected to a router, please
first find out the DHCP/IP address setting of the router and
setup a suitable IP address to the Access Point. Check the
manual on the CD for more setting details.
10
4. After the configuration is done, please change your PC’s IP
address back to original setting either “Obtain an IP address
automatically” / “Obtain DNS server address
automatically” or “Using the following IP address” / “Use
the following DNS server addresses”. Press “OK” to close.
Finally, connect the Access Point to your router or switch.
Now you can use the wireless card in your PC to connect to the
Internet / Intranet wirelessly as shown below:
11
Federal Communication Commission
Interference Statement
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
1. Reorient or relocate the receiving antenna.
2. Increase the separation between the equipment and receiver.
3. Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
4. Consult the dealer or an experienced radio technician for help.
FCC Caution
This device and its antenna must not be co-located or operating in
conjunction with any other antenna or transmitter.
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Any changes or modifications not expressly approved by the party
responsible for compliance could void the authority to operate equipment.
Federal Communications Commission (FCC) Radiation
Exposure Statement
This equipment complies with FCC radiation exposure set forth for an
uncontrolled environment. In order to avoid the possibility of exceeding the
FCC radio frequency exposure limits, human proximity to the antenna shall
not be less than 2.5cm (1 inch) during normal operation.
12
Federal Communications Commission (FCC) RF Exposure Requirements
SAR compliance has been established in the laptop computer(s)
configurations with PCMCIA slot on the side near the center, as tested in
the application for Certification, and can be used in laptop computer(s) with
substantially similar physical dimensions, construction, and electrical and
RF characteristics. Use in other devices such a PDAs or lappads is not
authorized.
This transmitter is restricted for use with the specific antenna(s) tested in
the application for Certification. The antenna(s) used for this transmitter
must not be co-located or operating in conjunction with any other antenna
or transmitter.
R&TTE Compliance Statement
This equipment complies with all the requirements of DIRECTIVE
1999/5/EC OF THE EUROPEAN PARLIAMENT AND THE COUNCIL of
March 9, 1999 on radio equipment and telecommunication terminal
Equipment and the mutual recognition of their conformity (R&TTE)
The R&TTE Directive repeals and replaces in the directive 98/13/EEC
(Telecommunications Terminal Equipment and Satellite Earth Station
Equipment) As of April 8, 2000.
Safety
This equipment is designed with the utmost care for the safety of those who
install and use it. However, special attention must be paid to the dangers of
electric shock and static electricity when working with electrical equipment.
All guidelines of this and of the computer manufacture must therefore be
allowed at all times to ensure the safe use of the equipment.
EU Countries Intended for Use
The ETSI version of this device is intended for home and office use in
Austria, Belgium, Denmark, Finland, France, Germany, Greece, Ireland,
Italy, Luxembourg, Bulgaria, Cyprus, Czech Republic, Estonia, Hungary,
Latvia, Lithuania, Malta, Poland, Romania, Slovakia, Slovenia, the
Netherlands, Portugal, Spain, Sweden, and the United Kingdom.
The ETSI version of this device is also authorized for use in EFTA member
states: Iceland, Liechtenstein, Norway, and Switzerland.
EU Countries not intended for use
None
A declaration of conformity is available on www.edimax.com
13
N20379
15
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising