The IR-2005 includes these items:
CHANNEL VISION
Limited Warranty
Channel Vision Technology will repair or replace any defect in material or
workmanship which occurs during normal use of this product with new or rebuilt
parts, free of charge in the USA, for two years from the date of original purchase.
This is a no hassle warranty with no mail in warranty card needed. This warranty
does not cover damages in shipment, failures caused by other products not
supplied by Channel Vision Technology, or failures due to accident, misuse,
abuse, or alteration of the equipment. This warranty is extended only to the
original purchaser, and a purchase receipt, invoice, or other proof of original
purchase date will be required before warranty repairs are provided.
IR-2005
(rear view)
Screwless decorator style trim ring
Single-gang decorator style IR wall plate
Mail in service can be obtained during the warranty period by calling (800) 8400288 toll free. A Return Authorization number must be obtained in advance and
can be marked on the outside of the shipping carton.
IR-2400 Plasma proof IR receiver
This warranty gives you specific legal rights and you may have other rights
(which vary from state to state). If a problem with this product develops during or
after the warranty period, please contact Channel Vision Technology, your dealer
or any factory-authorized service center.
IR-2005
(front view)
500-181 rev A1
How IR repeating works
The IR receiver is wired to
the IR hub which routes the
signal to IR emitters
Ba
>
FF>
tt
Tx
se
Pau
y>
Pla
Re
w<
<
p
Sto
3
rn
Lea
2
6
1
9
5
-/--
8
4
Vol
7
0
Po
we
r
Ch
or
Err
rn
Lea
Off
All
Off
Sat
er
Tun
DV
VC
Zone
IR
r
ive
ce
Re
el
Mod205
P-1
AN
NE
D
R
Point an
IR remote control
at the IR receiver
ion
pans
Ex
bal
r Glo
Pw
TV
CD
ect
Sel
L
TM
C H IS IO N
V
bal
Glo
Voltage requirements:
8 - 12 VDC
Max recommended wire length: 200 ft
IR Freq. range supported:
30 kHz - 60 kHz
IR pickup range:
40 ft. @ 38kHz, 25 ft. @ 56kHz
Mounting requirements:
Single-gang box or ring
Color:
White
Specifications subject to change without notice.
IR receiver window
rs
itte
Em
IR
ver
cei
Re
Specifications (typical)
Zone
DC
+12 mA
250
And the emitter CD player
repeats the IR signal
in the other room.
Be sure the emitter is attached directly over the
component’s IR receiver. To locate the IR receiver, shine a
flashlight into the unit and look for the sensor.
Features:
! Plasma Proof IR receiver
! Status LEDs for IR signal indication
! Mounts in a single-gang box or low-voltage ring
Single Room IR Setup
Whole-House IR Setup
IR-2005
IR-2005
(rear view)
A single room IR system can be created by connecting the
IR-2005 with the P-1205. Connect the three screw terminals
on the P-1205 to the screw terminals on the IR-2005 using
a 3-conductor wire (18-24AWG). CAT5 wire can be used,
but only 3 of the 8 conductors are needed.
IR-2005
(rear view)
IR-2005
IR1
IR2
IR3
IR4
IR5
IR6
IR7
IR8
+S- +S- +S- +S- +S- +S- +S- +SPOWER
IR BUS
C HANNEL V ISION
+S- + TM
C-1201
Central
1
The maximum recommend wire length
between IR-2005 and P-1205 is 200ft.
n
Expansio
bal Zone
Pwr Glo
eiver
3-conductor
18-24 AWG wire
Global
IR
r
Receive
The maximum recommend wire length
between IR-2005 and P-1205 is 200ft.
Model
P-1205
NEL
CHAN
V I S IO N
TM
Sat radio
Global
Emitter
IR
r
Receive
Emitter
DVD player
s
Zone
CD player
+12DC
Sat radio
DVD player
s
+12DC
n
bal Zone
Pwr Glo
TM
V
6
9
Expansio
IR Rec
eiver
IR Rec
3-conductor
18-24 AWG wire
Additional
IR receivers can
be connected
as needed.
3
5
8
0
Model
P-1205
NEL
CHAN
I S IO N
2
4
7
Po
wer
Zone
CD player
Receiver
Receiver
The diagram above illustrates how to create an IR system with IR receivers in
several different rooms in the house. Systems like this may include several different
styles of IR receivers depending on the specific application in each room.
">