Asus P6-P8H61E User`s manual

P6-P8H61E
ASUS PC (Desktop Barebone)
User’s Manual
E6509
First Edition V1
March 2011
Copyright © 2011 ASUSTeK Computer Inc. All Rights Reserved.
No part of this manual, including the products and software described in it, may be reproduced,
transmitted, transcribed, stored in a retrieval system, or translated into any language in any form or by any
means, except documentation kept by the purchaser for backup purposes, without the express written
permission of ASUSTeK Computer Inc. (“ASUS”).
Product warranty or service will not be extended if: (1) the product is repaired, modified or altered, unless
such repair, modification of alteration is authorized in writing by ASUS; or (2) the serial number of the
product is defaced or missing.
ASUS PROVIDES THIS MANUAL “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS
OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OR CONDITIONS OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. IN NO EVENT SHALL ASUS, ITS
DIRECTORS, OFFICERS, EMPLOYEES OR AGENTS BE LIABLE FOR ANY INDIRECT, SPECIAL,
INCIDENTAL, OR CONSEQUENTIAL DAMAGES (INCLUDING DAMAGES FOR LOSS OF PROFITS,
LOSS OF BUSINESS, LOSS OF USE OR DATA, INTERRUPTION OF BUSINESS AND THE LIKE),
EVEN IF ASUS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES ARISING FROM ANY
DEFECT OR ERROR IN THIS MANUAL OR PRODUCT.
SPECIFICATIONS AND INFORMATION CONTAINED IN THIS MANUAL ARE FURNISHED FOR
INFORMATIONAL USE ONLY, AND ARE SUBJECT TO CHANGE AT ANY TIME WITHOUT NOTICE,
AND SHOULD NOT BE CONSTRUED AS A COMMITMENT BY ASUS. ASUS ASSUMES NO
RESPONSIBILITY OR LIABILITY FOR ANY ERRORS OR INACCURACIES THAT MAY APPEAR IN THIS
MANUAL, INCLUDING THE PRODUCTS AND SOFTWARE DESCRIBED IN IT.
Products and corporate names appearing in this manual may or may not be registered trademarks or
copyrights of their respective companies, and are used only for identification or explanation and to the
owners’ benefit, without intent to infringe.
Offer to Provide Source Code of Certain Software
This product may contain copyrighted software that is licensed under the General Public License (“GPL”)
and under the Lesser General Public License Version (“LGPL”). The GPL and LGPL licensed code in this
product is distributed without any warranty. Copies of these licenses are included in this product.
You may obtain the complete corresponding source code (as defined in the GPL) for the GPL Software,
and/or the complete corresponding source code of the LGPL Software (with the complete machinereadable “work that uses the Library”) for a period of three years after our last shipment of the product
including the GPL Software and/or LGPL Software, which will be no earlier than December 1, 2011, either
(1) for free by downloading it from http://support.asus.com/download;
or
(2) for the cost of reproduction and shipment, which is dependent on the preferred carrier and the location
where you want to have it shipped to, by sending a request to:
ASUSTeK Computer Inc.
Legal Compliance Dept.
15 Li Te Rd.,
Beitou, Taipei 112
Taiwan
In your request please provide the name, model number and version, as stated in the About Box of the
product for which you wish to obtain the corresponding source code and your contact details so that we
can coordinate the terms and cost of shipment with you.
The source code will be distributed WITHOUT ANY WARRANTY and licensed under the same license as
the corresponding binary/object code.
This offer is valid to anyone in receipt of this information.
ASUSTeK is eager to duly provide complete source code as required under various Free Open Source
Software licenses. If however you encounter any problems in obtaining the full corresponding source code
we would be much obliged if you give us a notification to the email address [email protected], stating the
product and describing the problem (please do NOT send large attachments such as source code archives
etc to this email address).
ii
Table of contents
Notices............................................................................................................v
Safety information...........................................................................................vi
About this guide............................................................................................. vii
System package contents............................................................................. viii
Chapter 1:
System introduction
1.1
Welcome!........................................................................................ 1-2
1.2
Front panel ..................................................................................... 1-2
1.3
Rear panel....................................................................................... 1-4
1.4
Internal components........................................................................ 1-6
1.5
Qualified Vendors Lists (QVL)......................................................... 1-7
Chapter 2:
Starting up
2.1
Installing an operating system......................................................... 2-2
2.2
Powering up.................................................................................... 2-2
2.3
Support DVD information................................................................ 2-2
2.4
2.3.1
Running the support DVD................................................ 2-3
2.3.2
Utilities menu................................................................... 2-4
2.3.3
Make Disk menu.............................................................. 2-5
2.3.4
Manual menu................................................................... 2-5
2.3.5
ASUS Contact information............................................... 2-6
2.3.6
Other information............................................................. 2-6
Software information....................................................................... 2-8
2.4.1
AI Suite II......................................................................... 2-8
2.4.2
ASUS AI Manager.......................................................... 2-17
Chapter 3:
Motherboard info
3.1
Introduction..................................................................................... 3-2
3.2
Motherboard layout......................................................................... 3-2
3.3
Jumpers.......................................................................................... 3-3
3.4
Connectors...................................................................................... 3-4
Chapter 4:
4.1
BIOS setup
Managing and updating your BIOS................................................. 4-2
4.1.1
ASUS Update utility......................................................... 4-2
4.1.2
ASUS EZ Flash 2............................................................. 4-4
4.1.3
ASUS CrashFree BIOS 3................................................. 4-5
4.1.4
ASUS BIOS Updater........................................................ 4-6
iii
Table of contents
4.2
BIOS setup program....................................................................... 4-9
BIOS menu screen.......................................................................... 4-9
4.3
4.4
4.5
Main menu.................................................................................... 4-13
4.3.1
System Language [English]........................................... 4-13
4.3.2
System Date [Day xx/xx/xxxx]........................................ 4-13
4.3.3
System Time [xx:xx:xx].................................................. 4-13
4.3.4
Security.......................................................................... 4-13
Advanced menu............................................................................ 4-15
4.4.1
CPU Configuration......................................................... 4-15
4.4.2
System Agent Configuration.......................................... 4-16
4.4.3
PCH Configuration......................................................... 4-17
4.4.4
SATA Configuration........................................................ 4-17
4.4.5
USB Configuration......................................................... 4-18
4.4.6
Onboard Devices Configuration..................................... 4-18
4.4.7
APM............................................................................... 4-19
Monitor menu................................................................................ 4-19
4.5.1
CPU Temperature / MB Temperature [xxxºC/xxxºF]....... 4-20
4.5.2CPU / Chassis / Power Fan Speed [xxxx RPM]
4.6
4.7
4.8
or [Ignore] / [N/A]............................................................ 4-20
4.5.3
CPU Q-Fan Control [Enabled]....................................... 4-20
4.5.4
Chassis Q-Fan Control [Enabled].................................. 4-20
4.5.5
CPU Voltage, 3.3V Voltage, 5V Voltage, 12V Voltage... 4-20
Boot menu..................................................................................... 4-21
4.6.1
Bootup NumLock State [On].......................................... 4-21
4.6.2
Full Screen Logo [Enabled]............................................ 4-21
4.6.3
Wait for ‘F1’ if Error [Enabled]........................................ 4-21
4.6.4
Option ROM Messages [Force BIOS]............................ 4-21
4.6.5
Setup Mode [EZ Mode].................................................. 4-22
4.6.6
Boot Option Priorities..................................................... 4-22
4.6.7
Boot Override................................................................. 4-22
Tools menu.................................................................................... 4-23
4.7.1
ASUS EZ Flash 2........................................................... 4-23
4.7.2
ASUS SPD Information.................................................. 4-23
Exit menu...................................................................................... 4-24
ASUS contact information.......................................................................... 4-25
iv
Notices
ASUS Recycling/Takeback Services
ASUS recycling and takeback programs come from our commitment to the highest standards
for protecting our environment. We believe in providing solutions for you to be able to
responsibly recycle our products, batteries, other components, as well as the packaging
materials. Please go to http://csr.asus.com/english/Takeback.htm for the detailed recycling
information in different regions.
REACH
Complying with the REACH (Registration, Evaluation, Authorisation, and Restriction of
Chemicals) regulatory framework, we published the chemical substances in our products at
ASUS REACH website at http://csr.asus.com/english/REACH.htm
Federal Communications Commission Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions:
•
This device may not cause harmful interference, and
•
This device must accept any interference received including interference that may
cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with manufacturer’s instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur
in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or more of the following measures:
•
Reorient or relocate the receiving antenna.
•
Increase the separation between the equipment and receiver.
•
Connect the equipment to an outlet on a circuit different from that to which the receiver
is connected.
•
Consult the dealer or an experienced radio/TV technician for help.
WARNING! The use of shielded cables for connection of the monitor to the graphics card
is required to assure compliance with FCC regulations. Changes or modifications to this
unit not expressly approved by the party responsible for compliance could void the user’s
authority to operate this equipment.
Canadian Department of Communications Statement
This digital apparatus does not exceed the Class B limits for radio noise emissions from
digital apparatus set out in the Radio Interference Regulations of the Canadian Department
of Communications.
This class B digital apparatus complies with Canadian ICES-003.
Safety information
Electrical safety
•
To prevent electric shock hazard, disconnect the power cable from the electric outlet
before relocating the system.
•
When adding or removing devices to or from the system, ensure that the power cables
for the devices are unplugged before the signal cables are connected. If possible,
disconnect all power cables from the existing system before you add a device.
•
Before connecting or removing signal cables from the motherboard, ensure that all
power cables are unplugged.
•
Seek professional assistance before using an adapter or extension cord. These
devices could interrupt the grounding circuit.
•
Ensure that your power supply is set to the correct voltage in your area. If you are not
sure about the voltage of the electrical outlet you are using, contact your local power
company.
•
If the power supply is broken, do not try to fix it by yourself. Contact a qualified service
technician or your retailer.
Operation safety
•
Before installing the motherboard and adding devices on it, carefully read all the
manuals that came with the package.
•
Before using the product, ensure that all cables are correctly connected and the power
cables are not damaged. If you detect any damage, contact your dealer immediately.
•
To avoid short circuits, keep paper clips, screws, and staples away from connectors,
slots, sockets and circuitry.
•
Avoid dust, humidity, and temperature extremes. Do not place the product in any area
where it may become wet.
•
Place the product on a stable surface.
•
If you encounter technical problems with the product, contact a qualified service
technician or your retailer.
Lithium-Ion Battery Warning
CAUTION: Danger of explosion if battery is incorrectly replaced. Replace only with the
same or equivalent type recommended by the manufacturer. Dispose of used batteries
according to the manufacturer’s instructions.
VORSICHT: Explosionsgetahr bei unsachgemäßen Austausch der Batterie. Ersatz nur
durch denselben oder einem vom Hersteller empfohlenem ähnljchen Typ. Entsorgung
gebrauchter Batterien nach Angaben des Herstellers.
LASER PRODUCT WARNING
CLASS 1 LASER PRODUCT
vi
About this guide
Audience
This guide provides general information and installation instructions about the ASUS Vintage
V-Series P8H61E barebone system. This guide is intended for experienced users and
integrators with hardware knowledge of personal computers.
How this guide is organized
This guide contains the following parts:
1. Chapter 1: System introduction
2.
This chapter gives a general description of the ASUS
V-Series P8H61E. The chapter lists the system features, including introduction on the
front and rear panel, and internal components.
Chapter 2: Starting up
3.
This chapter helps you power up the system and install drivers and utilities from the
support DVD.
Chapter 3: Motherboard info
4.
This chapter gives information about the motherboard that comes with the system. This
chapter includes the motherboard layout, jumper settings, and connector locations.
Chapter 4: BIOS setup
This chapter tells how to change system settings through the BIOS Setup menus and
describes the BIOS parameters.
Conventions used in this guide
W
ARNING: Information to prevent injury to yourself when trying to complete a
task.
AUTION: Information to prevent damage to the components when trying to
C
complete a task.
IMPORTANT: Instructions that you MUST follow to complete a task.
NOTE: Tips and additional information to aid in completing a task.
Where to find more information
Refer to the following sources for additional information and for product and software
updates.
1. ASUS Websites
2.
The ASUS websites worldwide provide updated information on ASUS hardware and
software products. Refer to the ASUS contact information.
Optional Documentation
Your product package may include optional documentation, such as warranty flyers,
that may have been added by your dealer. These documents are not part of the
standard package.
vii
System package contents
Check your P6-P8H61E system package for the following items.
If any of the items is damaged or missing, contact your retailer immediately.
Item description
viii
1.
ASUS P6-P8H61E barebone system with
• ASUS motherboatd
• Power supply unit
• ASUS chassis
• CPU cooler
2.
Cable
• AC power cable
3.
Support DVD
4.
Quick Installation Guide
This chapter gives a general description of
the ASUS P6-P8H61E. The chapter lists
the system features including introduction
on the front and rear panel, and internal
components.
System introduction
Chapter 1
1.1
Welcome!
Thank you for choosing the ASUS P6-P8H61E!
The ASUS P6-P8H61E is an all-in-one barebone system with a versatile home entertainment
feature.
The system comes in a stylish casing and powered by the ASUS motherboard that supports
the Intel® Lynnfield/Clarkdale Dual-Core / Quad-Core processors in the 1156-land package.
The system supports up to 8 GB of system memory using DDR3 DIMMs. High-resolution
graphics via integrated graphics controller or PCI Express x16 slot, Serial ATA, USB 2.0, and
8-channel audio feature the system and take you ahead in the world of power computing.
1.2
Front panel
The front panel includes the optical drive bays, power button, and several I/O ports are
located at the front panel.
3
1
1
3
4
5
6
2
7
1-2
Chapter 1: System introduction
1.
Power button. Press this button to turn the system on.
2.
Front panel cover. Push
3.
Optical disk drive cover. Push
4.
Microphone port. This Mic (pink) port connects a microphone.
5.
Headphone port. This Line out (lime) port connects a headphone with a stereo miniplug.
6.
USB 3.0 ports. These Universal Serial Bus 3.0 (USB 3.0) ports are available for
connecting USB 3.0 devices such as a mouse, printer, scanner, camera, PDA, and
others.
7.
Multimedia Card / Secure Digital™ / MemoryStick® / Memory Stick Pro™ card
slot.
ASUS P6-P8H61E
to open the front panel cover.
to eject the optical disk drive.
1-3
1.3
Rear panel
The system rear panel includes the power connector and several I/O ports that allow
convenient connection of devices.
2
1
4
6
3
7
5
8
10
9
11
12
14
13
15
Do NOT cover the rear vent , and the ambient temperature is limited up to 35oC to prevent
the system from overheating.
1-4
1.
Chassis air vent. The vent is for ventilation inside the system chassis.
2.
Power supply unit fan vent. This vent is for the PSU fan that provides ventilation
inside the power supply unit.
3.
Chassis fan vent. This vent is for the fan that provides ventilation inside the system
chassis.
4.
Power connector. This connector is for the power cable and plug.
Chapter 1: System introduction
5.
Line In port (light blue). This port connects the tape, CD, DVD player, or other audio
sources.
6.
Line Out port (lime). This port connects a headphone or a speaker. In 4-channel, 6channel, and 8-channel configuration, the function of this port becomes Front Speaker
Out.
7.
Microphone port (pink). This port connects a microphone.
8.
Side Speaker Out port (gray). This port connects the side speaker in an 8-channel
audio configuration.
9.
Rear Speaker Out port (black). This port connects the rear speakers in a 4-channel,
6-channel, or 8-channel audio configuration.
10. Center / Subwoofer port (orange). This port connects the center/subwoofer speakers.
Refer to the audio configuration table below for the function of the audio ports in 2, 4, 6, or
8-channel configuration.
Audio 2, 4, 6, or 8-channel configuration
Port
Light Blue
Lime
Pink
Orange
Black
Gray
11.
Headset
2channel
Line In
Line Out
Mic In
–
–
–
4-channel
6-channel
8-channel
Line In
Front Speaker Out
Mic In
–
Rear Speaker Out
–
Line In
Front Speaker Out
Mic In
Center/Subwoofer
Rear Speaker Out
–
Line In
Front Speaker Out
Mic In
Center/Subwoofer
Rear Speaker Out
Side Speaker Out
LAN (RJ-45) port. This port allows gigabit connection to a Local Area Network (LAN)
through a network hub. Refer to the table below for the LAN port LED indications.
LAN port LED indications
Activity/Link Speed LED
Status
Description Status
OFF
ORANGE
BLINKING
ASUS P6-P8H61E
No link
Linked
Data activity
OFF
ORANGE
GREEN
Description
10 Mbps connection
100 Mbps connection
1 Gbps connection
ACT/LINK SPEED
LED
LED
LAN port
1-5
12. USB 2.0 ports 1 ~ 4. These 4-pin Universal Serial Bus (USB) ports are available for
connecting USB 2.0 devices.
13. Video Graphics Adapter (VGA) port. This 15-pin port is for a VGA monitor or other
VGA-compatible devices.
14. HDMI port. This is a High-Definition Mulltimedia Interface (HDMI) connector, and is
HDCP compliant allowing playback of HD DVD, Blu-Rau discs, and other protected
content.
15. Expansion slot covers. Remove these covers when installing expansion cards.
1.4
Internal components
The illustration below is the internal view of the system when you remove the side cover and
the power supply unit. The installed components are labeled for your reference.
4
2
3
1
5
5
6
1-6
7
1.
Front panel cover
5.
ASUS motherboard
2.
5.25-inch optical drive bays
6.
Expansion slot metal brackets
3.
Hard disk drive bay
7.
Metal bracket lock
4.
Power supply unit (under the HDD bay)
•
Refer to the bundled Quick Installation Guide for installing additional system
components and get assistance from professionals when you disassemble or
assemble the system.
•
Refer to the Chapter 4 in this user guide for motherboard details.
Chapter 1: System introduction
1.5
Qualified Vendors Lists (QVL)
DDR3-1333 MHz capability
Chip
Brand
Chip No.
Timing
Voltage
DIMM
socket
support
(Optional)
Vendors
Part No.
Size
SS/
DS
A
B
A-Data
AD31333001GOU
1GB
SS
A-Data
AD30908C8D-151C
E0906
-
-
•
•
A-Data
AD31333G001GOU
3GB
(3 x 1GB)
SS
-
-
8-8-8-24
1.65-1.85V
•
•
Apacer
78.A1GC6.9L1
2GB
DS
APACER
AM5D5808DEWSBG
-
-
•
•
Apacer
78.A1GC6.9L1
2GB
DS
Apacer
AM5D5808FEQSBG
9
-
•
•
CORSAIR
TW3X4G1333C9D G
4GB
(2 x 2GB)
DS
-
-
9-9-9-24
1.50V
•
•
CORSAIR
CMX8GX3M4A1333C9
8GB
(4 x 2GB)
DS
-
-
9-9-9-24
1.50V
•
•
Crucial
CT25664BA1339.16FF
2GB
DS
Micron
9KF27D9KPT
9
-
•
•
Crucial
BL25664BN1337.16FF
(XMP)
6GB
(3 x 2GB)
DS
-
-
7-7-7-24
1.65V
•
•
G.SKILL
F3-10600CL8D2GBHK(XMP)
1GB
SS
G.SKILL
-
-
-
•
•
G.SKILL
F3-10666CL7T3GBPK(XMP)
3GB
(3 x 1GB)
SS
-
-
7-7-7-18
1.5~1.6V
•
•
G.SKILL
F3-10666CL8D4GBECO(XMP)
4GB
(2 x 2GB)
DS
-
-
8-8-8-8-24
XMP
1.35V
•
•
G.SKILL
F3-10666CL7D8GBRH(XMP)
8GB
(2 x 4GB)
DS
-
-
7-7-7-21
1.5V
•
•
GEIL
GV32GB1333C9DC
2GB
(2 x 1GB)
DS
-
-
9-9-9-24
1.5V
•
•
GEIL
GV34GB1333C9DC
4GB
(2 x 2GB)
DS
-
-
9-9-9-24
1.5V
•
•
Hynix
HMT125U6TFR8A-H9
2GB
DS
HYNIX
H5TC1G83TFRH9A
-
1.35V
(low
voltage)
•
•
HYNIX
HMT351U6BFR8C-H9
4GB
DS
HYNIX
H5TQ2G83BFRH9C
-
-
•
•
KINGMAX
FLFE85F-C8KM9 NAES
2GB
SS
KINGMAX
KFC8FNMXFBXX-15A
-
-
•
•
KINGMAX
FLFE85F-B8KL9 NEES
2GB
DS
KINGMAX
KKB8FNWBFGNX26A
-
-
•
•
KINGMAX
FLFF65F-C8KM9 NEES
4GB
DS
KINGMAX
KFC8FNMXFBXX-15A
-
-
•
•
Kingston
KVR1333D3N9/2G
2GB
DS
ELPIDA
J1108BDSE-DJ-F
9
1.5V
•
•
Kingston
KHX1333C9D3UK2/
4GX(XMP)
4GB
(2 x 2GB)
DS
-
-
9
XMP
1.25V
•
•
KINGSTON
KVR1333D3N9/4G
4GB
DS
HYNIX
H5TQ2G83AFRH9C
9
1.5V
•
•
KINGSTON
KVR1333D3N9/4G
4GB
DS
Hynix
H5TQ2G83AFR
-
-
•
•
MICRON
MT8JTF25664AZ-1G4D1
2GB
SS
MICRON
OJD12D9LGK
-
-
•
•
continued on the next page
ASUS P6-P8H61E
1-7
DDR3-1333 MHz capability
Vendors
Part No.
Size
SS/
DS
Chip
Brand
Chip No.
Timing
Voltage
DIMM
socket
support
(Optional)
A
B
OCZ
OCZ3F13334GK
4GB
(2 x 2GB)
DS
-
-
9-9-9-20
1.7V
•
•
OCZ
OCZ3X1333LV6GK(XMP)
6GB(3 x
2GB)
DS
-
-
8-8-8-20
1.60V
•
•
PSC
AL8F8G73D-DG1
2GB
DS
PSC
A3P1GF3DGF
8-8-8-24
1.5V
•
•
SAMSUNG
M378B5673FH0-CH9
2GB
DS
SAMSUNG
K4B1G0846F
-
-
•
•
Super Talent
W1333UA1GH
1GB
SS
HYNIX
H5TQ1G83TFR
9
-
•
•
Super Talent
W1333X2G8(XMP)
1GB
SS
-
-
8
-
•
•
Transcend
TS256MLK64V3U
2GB
DS
Micron
9GF27D9KPT
-
-
•
•
DDR3-1066 MHz capability
DIMM
socket
support
(Optional)
Vendors
Part No.
Size
SS/
DS
Chip
Brand
Chip No.
Timing
Voltage
A
B
ELPIDA
EBJ21UE8EDF0AE-F
2GB
DS
ELPIDA
J1108EDSE-DJ-F
-
1.35V
(low
voltage)
•
•
KINGSTON
KVR1066D3N7/1G
1GB
SS
KTC
D1288JPNDPLD9U
7
1.5V
•
•
KINGSTON
KVR1066D3N7/4G
4GB
DS
Hynix
H5TQ2G83AFR
7
1.5V
•
•
Micron
MT8JTF12864AZ1G1F1
1GB
SS
Micron
9GF22D9KPT
7
-
•
•
OCZ
OCZ3G1066LV4GK
4GB
(2 x 2GB)
DS
Micron
9BF27D9KPV
7-7-7-20
1.65V
•
•
SS - Single-sided / DS - Double-sided
DIMM support:
•A*: Supports one module inserted in any slot as Single-channel
memory configuration.
•B*: Supports one pair of modules inserted into both slots as
one pair of Dual-channel memory configuration.
Visit the ASUS website at www.asus.com for the latest QVLs.
1-8
Chapter 1: System introduction
Chapter 2
Starting up
This chapter helps you power up the system
and install drivers and utilities from the
support DVD.
2.1
Installing an operating system
The barebone system supports Windows® XP/Vista/7 operating systems (OS). Always install
the latest OS version and corresponding updates so you can maximize the features of your
hardware.
Motherboard settings and hardware options vary. Use the setup procedures presented
in this chapter for general reference only. Refer to your OS documentation for more
information.
2.2
•
Windows XP OS setup cannot recognize Serial ATA hard drives in a RAID set without
the necessary drivers. Use a RAID driver disk when installing Windows XP OS to a
Serial ATA hard drive included in a RAID set.
•
From the Windows XP setup screen, press F6 when prompted then follow succeeding
screen instructions to install the SATA drivers.
Powering up
Press the system power button ( ) to enter the OS.
Press to turn ON the system
2.3
Support DVD information
The support DVD that came with the system contains useful software and several utility
drivers that enhance the system features.
2-2
•
Screen display and driver options may not be the same for different operating system
versions.
•
The contents of the support DVD are subject to change at any time without notice.
Visit the ASUS website at www.asus.com for updates.
Chapter 2: Starting up
2.3.1
Running the support DVD
To begin using the support DVD, place the DVD in your optical drive. The DVD automatically
displays the Drivers menu if Autorun is enabled in your computer.
Click an icon to
display support
DVD/motherboard
information
Click an item to install
If Autorun is NOT enabled in your computer, browse the contents of the support DVD to
locate the file ASSETUP.EXE from the BIN folder. Double-click the ASSETUP.EXE to run
the DVD.
ASUS InstAll
Launches the ASUS InstAll driver installation wizard.
Reaktek Audio Driver
Installs the Realtek audio driver and application.
Intel Graphics Accelerator Driver
Installs the Intel® Graphics Accelerator Driver.
Browser Configuration Utility
Installs the Browser Configuration Utility.
Management Engine Interface
Installs the Management Engine Interface.
USB 3.0 Driver
Installs the USB 3.0 driver.
PC-cillin 2010
Installs the PC-cillin 2010 utility.
ASUS P6-P8H61E
2-3
2.3.2
Utilities menu
The Utilities menu shows the applications and other software that the motherboard supports.
ASUS InstAll
Installs all the utilities through the Installation Wizard.
Realtek Ethernet Utility
Installs the Realtek Ethernet Utility.
ASUS AI Manager
Installs ASUS AI Manager.
ASUS AI Suite II
Installs the ASUS AI Suite II.
Adobe Reader 10.0
Installs the Adobe® Reader that allows you to open, view, and print documents in Portable
Document Format (PDF).
Internet Radio
Installs the Internet Radio.
2-4
Chapter 2: Starting up
2.3.3
Make Disk menu
The Make disk menu allows you to make a AHCI driver disk.
2.3.4
Manual menu
The Manual menu contains the list of supplementary user manuals. Click an item to open the
folder of the user manual.
Most user manuals are in Portable Document Format (PDF). Install the Adobe® Reader
from the Utilities menu before opening a user manual.
ASUS P6-P8H61E
2-5
2.3.5
ASUS Contact information
Click the Contact tab to display the ASUS contact information. You can also find this
information on the inside front cover of this user guide.
2.3.6
Other information
The icons on the top right corner of the screen give additional information on the motherboard
and the contents of the support DVD. Click an icon to display the specified information.
Motherboard Info
Displays the general specifications of the motherboard.
2-6
Chapter 2: Starting up
Browse this DVD
Displays the support DVD contents in graphical format.
Filelist
Displays the contents of the support DVD and a brief description of each in text format.
ASUS P6-P8H61E
2-7
2.4
Software information
Most of the applications in the support DVD have wizards that will conveniently guide you
through the installation. View the online help or readme file that came with the software for
more information.
2.4.1
AI Suite II
ASUS AI Suite II is an all-in-one interface that integrates several ASUS utilities and allows
users to launch and operate these utilities simultaneously.
Installing AI Suite II
To install AI Suite II:
1.
Place the support DVD in the optical drive. The Drivers installation tab appears if your
computer has enabled the Autorun feature.
2.
Click the Utilities tab, then click ASUS AI Suite II.
3.
Follow the onscreen instructions to complete the installation.
Using AI Suite II
AI Suite II automatically starts when you enter the Windows® operating system (OS). The AI
Suite II icon appears in the Windows® notification area. Click the icon to open the AI Suite II
main menu bar.
Click each button to select and launch a utility, to monitor the system, to update the
motherboard BIOS, to display the system information, and to customize the settings of AI
Suite II.
Click to
customize the
interface settings
Click to show links to
the support sites
Click to update the motherboard BIOS
Click to monitor sensors or CPU frequency
Click to select a utility
2-8
Chapter 2: Starting up
EPU
EPU is an energy-efficient tool that satisfies different computing needs. This utility provides
several modes that you can select to save system power. Selecting Auto mode will have the
system shift modes automatically according to current system status. You can also customize
each mode by configuring settings like CPU frequency, GPU frequency, vCore Voltage, and
Fan Control.
Launching EPU
After installing AI Suite II from the support DVD, launch EPU by clicking Tool > EPU on the AI
Suite II main menu bar.
Displays the following
message if no VGA power
saving engine is detected.
Displays current mode
The items lighting up
means power saving
engine is activated
Displays the amount of
CO2 reduced
*Shifts between the
display of Total and
Current CO2 reduced
Displays the
current CPU power
Advanced settings for each mode
Multiple system
operating modes
Displays the system
properties of each
mode
*•
Select From EPU Installation to show the CO2 that has been reduced since you
installed EPU.
*•
Select From the Last Reset to show the total CO2 that has been reduced since you
click the Clear button
.
ASUS P6-P8H61E
2-9
Probe II
Probe II is a utility that monitors the computer’s vital components, and detects and alerts you
of any problem with these components. Probe II senses fan rotations, CPU temperature,
and system voltages, among others. With this utility, you are assured that your computer is
always at a healthy operating condition.
Launching Probe II
After installing AI Suite II from the support DVD, launch Probe II by clicking Tool > Probe II on
the AI Suite II main menu bar.
Configuring Probe II
Click the Voltage/Temperature/Fan Speed tabs to activate the sensors or to adjust the sensor
threshold values. The Preference tab allows you to customize the time interval of sensor
alerts, or change the temperature unit.
Saves your
configuration
Loads your saved
configuration
2-10
Loads the default
threshold values for
each sensor
Applies your
changes
Chapter 2: Starting up
Sensor Recorder
Sensor Recorder allows you to monitor the changes in the system voltage, temperature, and
fan speed, as well as recording the changes.
Launching Sensor Recorder
After installing AI Suite II from the support DVD, click Tool > Sensor Recorder on the AI
Suite II main menu bar to launch PC Probe.
Configuring Sensor Recorder
Click the Voltage/Temperature/Fan Speed tabs and select the sensors that you want to
monitor. The History Record tab allows you to record the changes in the sensors that you
enable.
Select the
sensors that
you want to
monitor
Drag to view
the status
during a
certain period
of time
Click to zoom
in/out the Y axis
Click to return
to the default
mode
ASUS P6-P8H61E
Click to zoom
in/out the X axis
2-11
Monitor
The Monitor section includes the Sensor and
CPU Frequency panels.
Sensor
The Sensor panel displays the current value of a system sensor such as fan rotation, CPU
temperature, and voltages. Click Monitor > Sensor on the AI Suite II main menu bar to
launch the Sensor panel.
CPU Frequency
The CPU Frequency panel displays the current CPU frequency and CPU usage. Click
Monitor > CPU Frequency on the AI Suite II main menu bar to open the CPU Frequency
panel.
Resident in the right pane (system information area)
2-12
Sensor panel
CPU Frequency panel
Chapter 2: Starting up
Update
The Update section allows you to update the motherboard BIOS and the BIOS boot logo with
the ASUS designed update utilities.
ASUS Update
The ASUS Update is a utility that allows you to manage, save, and update the motherboard
BIOS in Windows® OS. The ASUS Update utility allows you to update the BIOS directly
from the Internet, download the latest BIOS file from the Internet, update the BIOS from an
Updating the BIOS through the Internet
To update the BIOS through the Internet:
1.
From the ASUS Update screen,
select Update BIOS from Internet,
and then click Next.
2.
Select the ASUS FTP site nearest
you to avoid network traffic.
If you want to enable the BIOS
downgradable function and auto
BIOS backup function, check the
checkboxs before the two items on
the screen.
3.
Select the BIOS version that you
want to download. Click Next.
When there is not updated version
detected, it is shown as the screen
on the right side.
ASUS P6-P8H61E
2-13
4.
You can decide whether to change
the BIOS boot logo, which is the
image appearing on screen during
the Power‑On Self-Tests (POST).
Click Yes if you want to change the
boot logo or No to continue.
5.
Follow the onscreen instructions to
complete the update process.
Updating the BIOS through a BIOS
file
To update the BIOS through a BIOS file:
2-14
1.
From the ASUS Update screen,
select Update BIOS from file, and
then click Next.
2.
Locate the BIOS file from the Open
window, click Open, and click Next.
3.
You can decide whether to change
the BIOS boot logo. Click Yes if you
want to change the boot logo or No to
continue.
4.
Follow the onscreen instructions to
complete the update process.
Chapter 2: Starting up
System Information
The System Information section displays the
information about the motherboard, CPU, and
memory slots.
•
Click the MB tab to see the details on
the motherboard manufacturer, product
name, version, and BIOS.
•
Click the CPU tab to see the details on
the processor and the Cache.
•
Click the SPD tab and then select
the memory slot to see the details on
the memory module installed on the
corresponding slot.
ASUS P6-P8H61E
2-15
Settings
The Settings section allows you to customize the
main menu bar settings and the interface’s skin.
2-16
•
Application allows you to select the
application that you want to enable.
•
Bar allows you to modify the bar setting,
•
Skin allows you to customize the
interface’s contrast, brightness,
saturation, hue, and gamma.
Chapter 2: Starting up
2.4.2
ASUS AI Manager
ASUS AI Manager is a utility that gives you quick and easy access to frequently-used
applications.
Installing AI Manager
To install AI Manager on your computer:
1.
Place the support CD in the optical drive. If Autorun is enabled, the Drivers installation
wizard appears.
If Autorun is not enabled in your computer, locate the setup.exe file from the ASUS AI
Manager folder in the support CD. Double-click the setup.exe file to start installation.
2.
Click the Utilities tab, then click ASUS AI Manager.
3.
Follow the screen instructions to complete the installation.
Launching AI Manager
To launch the AI Manager from the Windows® desktop, click Start > All Programs > ASUS >
AI Manager 1.xx.xx > AI Manager. The AI Manager quick bar appears on the desktop.
After launching the application, the AI Manager icon appears in the Windows® taskbar.
Right-click this icon to switch between quick bar and main
window, and to launch the AI Manager either from the quick bar
or taskbar.
ASUS P6-P8H61E
2-17
AI Manager quick bar
The AI Manager quick bar saves the desktop space and allows you to launch the ASUS
utilities or display system information easily. Click the Main, My Favorites, Support or
Information tab to display the menu’s contents.
Click the Maximize/restore button
to switch between full window and quick bar. Click the
Minimize button
to keep the AI Manager on the taskbar. Click the Close button
to quit
the AI Manager.
Close button
Maximize / restore button
Minimize button
Main
Support
My Favorites
Information
Main
The Main menu contains five utilities: AI Disk, AI Security, and AI Booting. Click the arrow
on the Main menu icon to browse through the utilities in the main menu.
Click to extend or restore
AI Disk
AI Disk allows you to easily clear temporary IE files, IE cookies, IE URLs, IE history, or the
Recycle Bin. Click the AI Disk icon on the quick bar to display the full AI Disk window and
select the items you want to clear. Click Apply when done.
2-18
Chapter 2: Starting up
AI Security
AI Security enables you to set a password to secure your devices, such as USB flash disks
and CD/DVD disks, from unauthorized access.
To lock a device:
1.When using AI Security for the first time, you are asked to set a password. Enter a
password with at most 20 alphanumeric characters.
2
Confirm the password.
3.
Key in the password hint (recommended).
4.
When done, click Ok.
5.
Select the device you want to lock, then click Apply.
6.Key in the password you have set previously, then click Ok. The selected device
is locked and not accessible.
To unlock the selected device:
1.
2.Key in the password you have set previously, then click Ok. The selected device
is unlocked.
To change password:
Click Change Password, then follow the on-screen instructions to change password.
Uncheck the checkbox of the selected device, then click Apply.
ASUS P6-P8H61E
2-19
AI Booting
AI Booting allows you to specify the boot device priority sequence.
To specify the boot sequence:
1.
Select a device, then click on the left/right button to specify the boot sequence.
2.
When done, press Apply.
My Favorites
My Favorites allows you to add applications that you frequently use, saving you from
searching for the applications throughout your computer.
To add an application:
1.
Click Add, then locate the application you want to add to My Favorites.
2.
Click Open on the file location window. The application is added to My Favorites list.
Right click on the application icon to launch, delete, or rename the selected application. You
can also double click to launch the selected application.
2-20
Chapter 2: Starting up
Support
Click any links on the Support window to go to the ASUS website, technical support website,
download support website, or contact information.
Information
Click the tab on the Information window to see the detailed information about your system,
motherboard, CPU, BIOS, installed devices, and memory.
ASUS P6-P8H61E
2-21
2-22
Chapter 2: Starting up
This chapter gives information about he
motherboard that comes with the system.
This chapter includes the motherboard
layout, jumper settings, and connector
locations.
Motherboard info
Chapter 3
Motherboard layout
3.2
Super
I/O
LAN1_USB12
USB34
VGA_HDMI
AUDIO
PCIEX1_1
4Mb
BIOS
PCIEX16_1
USB56
CPU_FAN
Intel®
H61
SATA3G_2 SATA6G_E2
SATA3G_3 SATA3G_1 SATA6G_E1
COM1
ASM
1061
P8H6110L/P6-P8H61E/DT_MB
ASM
1442
CHA_FAN1
SB_PWR
AD
2000B
RTL
8111E
SPDIF_OUT
33.5cm(13.2in)
LGA1155
DDR3 DIMM_A1 (64bit, 240-pin module)
DRAM_LED
MemOK!
DDR3 DIMM_B1 (64bit, 240-pin module)
CLRTC
DEBUGPORT
Lithium Cell
CMOS Power
EATXPWR
TPM
ATX12V
BUZZER
EPU
FRONT_
AUD
USB56
CR_CON1
ASM
1042
F_PANEL
Chapter 3: Motherboard info
3-2
Introduction
3.1
The P6-P8H61E barebone system comes with an ASUS motherboard. This chapter provides
technical information about the motherboard for future upgrades or system reconfiguration.
17.5cm(6.9in)
3.3
Jumpers
Clear RTC RAM (3-pin CLRTC)
This jumper allows you to clear the Real Time Clock (RTC) RAM in CMOS. You
can clear the CMOS memory of date, time, and system setup parameters by
erasing the CMOS RTC RAM data. The onboard button cell battery powers the
RAM data in CMOS, which include system setup information such as system
passwords.
P8H6110L/P6-P8H61E/DT_MB
CLRTC
2
2
Normal
(Default)
Clear RTC
1
3
P8H6110L/P6-P8H61E/DT_MB Clear RTC RAM
To erase the RTC RAM:
1.
Turn OFF the computer and unplug the power cord.
2.
Move the jumper cap from pins 1-2 (default) to pins 2-3. Keep the cap on pins 2-3 for
about 5-10 seconds, then move the cap back to pins 1-2.
3.
Plug the power cord and turn ON the computer.
4.
Hold down the <Del> key during the boot process and enter BIOS setup to re-enter
data.
Except when clearing the RTC RAM, never remove the cap on CLRTC jumper default
position. Removing the cap will cause system boot failure!
•
If the steps above do not help, remove the onboard battery and move the jumper again
to clear the CMOS RTC RAM data. After clearing the CMOS, reinstall the battery.
•
You do not need to clear the RTC when the system hangs due to overclocking. For
system failure due to overclocking, use the CPU Parameter Recall (C.P.R.) feature.
Shut down and reboot the system, then the BIOS automatically resets parameter
settings to default values.
ASUS P6-P8H61E
3-3
3.4
Connectors
1.Intel® H61 Serial ATA 3.0Gb/s connectors (7-pin SATA3G_1~3,
SATA6G_E1~2)
These connectors are for the Serial ATA signal cables for Serial ATA 3Gb/s or 6Gb/s
hard disk and optical disk drives.
GND
RSATA_TXP1
RSATA_TXN1
GND
RSATA_RXP1
RSATA_RXN1
GND
P8H6110L/P6-P8H61E/DT_MB
SATA3G_1
GND
RSATA_TXP3
RSATA_TXN3
GND
RSATA_RXP3
RSATA_RXN3
GND
SATA3G_3
SATA3G_2
GND
RSATA_RXN2
RSATA_RXP2
RSATA_TXN2
RSATA_TXP2
GND
GND
P8H6110L/P6-P8H61E/DT_MB Intel® SATA 3.0Gb/s connectors
P8H6110L/P6-P8H61E/DT_MB
SATA6G_E2
GND
RSATA_RXN2
RSATA_RXP2
RSATA_TXN2
RSATA_TXP2
GND
GND
GND
RSATA_TXP1
RSATA_TXN1
GND
RSATA_RXP1
RSATA_RXN1
GND
SATA6G_E1
P8H6110L/P6-P8H61E/DT_MB Intel® SATA 6.0Gb/s connectors
You must install Windows® XP Service Pack 3 or later version before using Serial ATA hard
disk drives.
3-4
Chapter 3: Motherboard info
2.CPU and chassis fan connectors (4-pin CPU_FAN, 4-pin CHA_FAN1)
Connect the fan cables to the fan connectors on the motherboard, ensuring that the
black wire of each cable matches the ground pin of the connector.
GND
CPU FAN PWR
CPU FAN IN
CPU FAN PWM
CPU_FAN
P8H6110L/P6-P8H61E/DT_MB
CHA_FAN1
GND
CHA FAN PWR
CHA FAN IN
CHA FAN PWM
P8H6110L/P6-P8H61E/DT_MB fan connectors
DO NOT forget to connect the fan cables to the fan connectors. Insufficient air flow inside
the system may damage the motherboard components. These are not jumpers! DO NOT
place jumper caps on the fan connectors!
Only the 4-pin CPU fan connector supports the ASUS Q-Fan feature.
ASUS P6-P8H61E
3-5
3.
Digital Audio connector (4-1 pin SPDIF_OUT)
This connector is for the S/PDIF audio module to allow digital sound output. Connect
one end of the S/PDIF audio cable to this connector and the other end to the S/PDIF
module.
SPDIF_OUT
P8H6110L/P6-P8H61E/DT_MB
GND
SPDIFOUT
+5V
P8H6110L/P6-P8H61E/DT_MB Digital audio connector
The S/PDIF out module is purchased separately.
4.
USB connectors (10-1 pin USB78, USB910, USB1112)
These connectors are for USB 2.0 ports. Connect the USB module cable to any of
these connectors, then install the module to a slot opening at the back of the system
chassis. These USB connectors comply with USB 2.0 specification that supports up to
480Mbps connection speed.
USB56
P8H6110L/P6-P8H61E/DT_MB
NC
GND
USB_P6+
USB_P6USB+5V
GND
USB_P5+
USB_P5USB+5V
PIN 1
P8H6110L/P6-P8H61E/DT_MBUSB2.0 connector
Never connect a 1394 cable to the USB connectors. Doing so will damage the
motherboard!
The USB 2.0 module is purchased separately.
3-6
Chapter 3: Motherboard info
5.
ATX power connectors (24-pin EATXPWR, 4-pin ATX12V)
These connectors are for ATX power supply plugs. The power supply plugs are
designed to fit these connectors in only one orientation. Find the proper orientation and
push down firmly until the connectors completely fit.
ATX12V
EATXPWR
+12V DC
+12V DC
PIN 1
PIN 1
+3 Volts
-12 Volts
GND
PSON#
GND
GND
GND
-5 Volts
+5 Volts
+5 Volts
+5 Volts
GND
P8H6110L/P6-P8H61E/DT_MB
+3 Volts
+3 Volts
GND
+5 Volts
GND
+5 Volts
GND
Power OK
+5V Standby
+12 Volts
+12 Volts
+3 Volts
GND
GND
P8H6110L/P6-P8H61E/DT_MB ATX power connectors
•
For a fully configured system, we recommend that you use a power supply unit
(PSU) that complies with ATX 12 V Specification 2.0 (or later version) and provides a
minimum power of 200W~250W.
•
DO NOT forget to connect the 4-pin ATX12V power plug; otherwise, the system will
not boot.
•
Use of a PSU with a higher power output is recommended when configuring a system
with more power-consuming devices. The system may become unstable or may not
boot up if the power is inadequate.
•
The ATX 12 V Specification 2.0-compliant (200W~250W) PSU has been tested to
support the motherboard power requirements.
ASUS P6-P8H61E
3-7
6.
System panel connector (10-1 pin PANEL)
This connector supports several chassis-mounted functions.
PLED+
PLEDPWR
GND
PWR LED PWR BTN
P8H6110L/P6-P8H61E/DT_MB
F_PANEL
HD_LED+
HD_LEDGround
Reset
PIN 1
HD_LED
RESET
P8H6110L/P6-P8H61E/DT_MB System panel connector
•
System power LED (2-pin PLED)
This 2-pin connector is for the system power LED. Connect the chassis power LED
cable to this connector. The system power LED lights up when you turn on the system
power, and blinks when the system is in sleep mode.
Hard disk drive activity LED (2-pin HDLED)
•
3-8
•
This 2-pin connector is for the HDD Activity LED. Connect the HDD Activity LED cable
to this connector. The IDE LED lights up or flashes when data is read from or written to
the HDD.
Power/Soft-off button (2-pin PWRBTN)
•
This 2-pin connector is for the system power button.
Reset button (2-pin RESET)
This 2-pin connector is for the chassis-mounted reset button for system reboot without
turning off the system power.
Chapter 3: Motherboard info
7.
Serial port connector (10-1 pin COM1)
This connector is for a serial (COM) port. Connect the serial port module cable to this
connector, then install the module to a slot opening at the back of the system chassis.
COM1
PIN 1
P8H6110L/P6-P8H61E/DT_MB
P8H6110L/P6-P8H61E/DT_MB Serial port (COM1) connector
The COM module is purchased separately.
8.
TPM connector (20-1 pin TPM)
This connector supports a Trusted Platform Module (TPM) system, which can securely
store keys, digital certificates, passwords, and data. A TPM system also helps enhance
network security, protects digital identities, and ensures platform integrity.
F_SERIRQ#
GND
PIN 1
P8H6110L/P6-P8H61E/DT_MB
GND
S_SMBCLIK_MAIN
S_SMBCLIK_MAIN
F_LAD2
F_LAD1
GND
C_PCICLK_TPM
F_FRAME#
S_PLTRST#
F_LAD3
+3V
F_LAD0
+3V
+3VSB
GND
S_PWRDWN#
TPM
P8H6110L/P6-P8H61E/DT_MB TPM Connector
The TPM module is purchased separately.
ASUS P6-P8H61E
3-9
3.4 MemOK! Switch
Installing DIMMs that are incompatible with the motherboard may cause system
boot failure, and the DRAM_LED near the MemOK! switch lights continuously. Press
and hold the MemOK! switch until the DRAM_LED starts blinking to begin automatic
memory compatibility tuning for successful boot.
P8H6110L/P6-P8H61E/DT_MB
P8H6110L/P6-P8H61E/DT_MB MemOK! switch
3-10
•
Refer to section 3.5 DRAM LED for the exact location of the DRAM_LED.
•
The DRAM_LED also lights when the DIMM is not properly installed. Turn off the
system and reinstall the DIMM before using the MemOK! function.
•
The MemOK! switch does not function under Windows® OS environment.
•
During the tuning process, the system loads and tests failsafe memory settings. It
takes about 30 seconds for the system to test one set of failsafe settings. If the test
fails, the system reboots and test the next set of failsafe settings. The blinking speed
of the DRAM_LED increases, indicating different test processes.
•
Due to memory tuning requirement, the system automatically reboots when each
timing set is tested. If the installed DIMMs still fail to boot after the whole tuning
process, the DRAM_LED lights continuously. Replace the DIMMs with ones
recommended in the Memory QVL (Qualified Vendors Lists) in this user manual or on
the ASUS website at www.asus.com.
•
If you turn off the computer and replace DIMMs during the tuning process, the system
continues memory tuning after turning on the computer. To stop memory tuning, turn
off the computer and unplug the power cord for about 5–10 seconds.
•
If your system fail to boot due to BIOS overclocking, press the MemOK! switch to boot
and load BIOS default settings. A message will appear during POST reminding you
that the BIOS has been restored to its default settings.
•
We recommend that you download and update to the latest BIOS version from the
ASUS website at www.asus.com after using the MemOK! function.
Chapter 3: Motherboard info
3.5 DRAM LED
DRAM LED checks the DRAM in sequence during motherboard booting process. If an
error is found , the LED next to the error device will continue lighting until the problem
is solved. This user-friendly design provides an intuitional way to locate the root
problem within a second.
P8H6110L/P6-P8H61E/DT_MB
DRAM LED
P8H6110L/P6-P8H61E/DT_MB DRAM LED
ASUS P6-P8H61E
3-11
3-12
Chapter 3: Motherboard info
Chapter 4
BIOS setup
This chapter tells how to change system
settings through the BIOS Setup menus and
describes the BIOS parameters.
4.1
Managing and updating your BIOS
BIOS (Basic Input and Output System) stores system settings such as storage device
configuration, overclocking settings, advanced power management, and boot device
configuration that are needed for system startup in the motherboard CMOS. In normal
circumstances, the default BIOS settings apply to most conditions to ensure optimum
performance. DO NOT change the default BIOS settings except in the following
circumstances:
•
An error message appears on the screen during the system startup and requests you
to run the BIOS setup.
•
You have installed a new system component that requires further BIOS settings or
update.
4.1.1
•
Inappropriate BIOS settings may result to system instability or boot failure. We
strongly recommend that you change the BIOS settings with the help of a trained
service personnel.
•
BIOS updating is potentially risky. If there is no problem in using the current BIOS
version, DO NOT manually update the BIOS. Inappropriate BIOS updating may result
to system boot failure.
•
Save a copy of the original motherboard BIOS file to a USB flash disk in case you
need to restore the BIOS in the future. Copy the original motherboard BIOS using the
ASUS Update utility.
•
Download the latest BIOS file from the ASUS website at www.asus.com.
ASUS Update utility
ASUS Update is a utility that allows you to manage, save, and update the motherboard BIOS
in Windows® environment.
4-2
•
ASUS Update requires an Internet connection either through a network or an Internet
Service Provider (ISP).
•
This utility is available in the support DVD that comes with the motherboard package.
Chapter 4: BIOS setup
Installing ASUS Update
To install ASUS Update:
1.
Place the support DVD in the optical drive. The Drivers menu appears.
2.
Click the Utilities tab, then click ASUS Update.
3.
Follow the onscreen instructions to complete the installation.
Quit all Windows® applications before you update the BIOS using this utility.
Updating the BIOS
To update the BIOS:
1.
From the Windows® desktop, click Start > Programs > ASUS > AI Suite II > AI Suite
II X.XX.XX to launch the AI Suite II utility. The AI Suite II Quick Bar appears.
2.
Click Update button from the Quick Bar, and then click ASUS Update from the popup
menu. The ASUS Update main screen appears. From the list, select either of the
following methods:’
Updating from the Internet
a. Select Update BIOS from the Internet, then click Next.
b.Select the ASUS FTP site nearest you to avoid network traffic, then click Next.
c.From the FTP site, select the BIOS version that you wish to download then click
Next.
The ASUS Update utility is capable of updating itself through the Internet. Always update
the utility to avail all its features.
Updating from a BIOS file
a. Select Update BIOS from file, then click Next.
b. Locate the BIOS file from the Open window, then click Open.
3.
Follow the onscreen instructions to complete the updating process.
ASUS V-Series P8H61E
4-3
4.1.2
ASUS EZ Flash 2
The ASUS EZ Flash 2 feature allows you to update the BIOS without using an OS‑based
utility.
Before you start using this utility, download the latest BIOS file from the ASUS website at
www.asus.com.
To update the BIOS using EZ Flash 2:
1.
Insert the USB flash disk that contains the latest BIOS file to the USB port.
2.
Enter the Advanced Mode of the BIOS setup program. Go to the Tool menu to select
ASUS EZ Flash Utility and press <Enter> to enable it.
Exit
ASUSTek EZ Flash 2 BIOS ROM Utility V01.02
Flash Info
MODEL: P6-P8H61E
VER: 0305
DATE: 03/09/2011
File Path: fs0:\
Drive
Folder Info
fs0:\
03/10/11
03:33p
4194304
P6-P8H61E.ROM
File Info
MODEL:
VER:
DATE
Help Info
[Enter] Select or Load
4-4
[Tab] Switch
[Up/Down/PageUp/PageDown/Home/End] Move
[Esc] Exit
[F2] Backup
Chapter 4: BIOS setup
3.
Press <Tab> to switch to the Drive field.
4.
Press the Up/Down arrow keys to find the USB flash disk that contains the latest BIOS,
and then press <Enter>.
5.
Press <Tab> to switch to the Folder Info field.
6.
Press the Up/Down arrow keys to find the BIOS file, and then press <Enter> to perform
the BIOS update process. Reboot the system when the update process is done.
4.1.3
•
This function supports USB flash disks with FAT 32/16 format and single partition only.
•
DO NOT shut down or reset the system while updating the BIOS to prevent system
boot failure!
ASUS CrashFree BIOS 3
The ASUS CrashFree BIOS 3 is an auto recovery tool that allows you to restore the BIOS file
when it fails or gets corrupted during the updating process. You can restore a corrupted BIOS
file using the motherboard support DVD or a USB flash drive that contains the updated BIOS
file.
The BIOS file in the support DVD may not be the latest version. Download the latest BIOS
file from the ASUS website at www.asus.com.
Recovering the BIOS
To recover the BIOS:
1.
Turn on the system.
2.
Insert the support DVD to the optical drive or the USB flash drive that contains the
BIOS file to the USB port.
3.
The utility automatically checks the devices for the BIOS file. When found, the utility
reads the BIOS file and enters ASUS EZ Flash 2 utility automatically.
4.
The system requires you to enter BIOS Setup to recover BIOS setting. To ensure
system compatibility and stability, we recommend that you press <F5> to load default
BIOS values.
DO NOT shut down or reset the system while updating the BIOS! Doing so can cause
system boot failure!
Ensure to load the BIOS default settings to ensure system compatibility and stability. Select
the Load Optimized Defaults item under the Exit menu. Refer to section 4.8 Exit menu
for details.
ASUS V-Series P8H61E
4-5
4.1.4
ASUS BIOS Updater
The ASUS BIOS Updater allows you to update BIOS in DOS environment. This utility also
allows you to copy the current BIOS file that you can use as a backup when the BIOS fails or
gets corrupted during the updating process.
The succeeding utility screens are for reference only. The actual utility screen displays may
not be same as shown.
Before updating the BIOS
1.
Prepare the motherboard support DVD and a USB flash drive in FAT32/16 format and
single partition.
2.
Download the latest BIOS file and BIOS Updater from the ASUS website at http://
support.asus.com and save them on the USB flash drive.
3.
•
NTFS is not supported under DOS environment. Do not save the BIOS file and BIOS
Updater to a hard disk drive or USB flash drive in NTFS format.
•
Do not save the BIOS file to a floppy disk due to low disk capacity.
Turn off the computer and disconnect all SATA hard disk drives (optional).
Booting the system in DOS environment
1.
Insert the USB flash drive with the latest BIOS file and BIOS Updater to the USB port.
2.
Boot your computer. When the ASUS Logo appears, press <F8> to show the BIOS
Boot Device Select Menu. Insert the support DVD into the optical drive and select the
optical drive as the boot device.
Please select boot device:
4-6
SATA: XXXXXXXXXXXXXXXX
USB XXXXXXXXXXXXXXXXX
UEFI: XXXXXXXXXXXXXXXX
Enter Setup
↑ and ↓ to move selection
ENTER to select boot device
ESC to boot using defaults
Chapter 4: BIOS setup
3. When the Make Disk menu appears, select the FreeDOS command prompt item by
pressing the item number.
4.
At the FreeDOS prompt, type d: and press <Enter> to switch the disk from
Drive C (optical drive) to Drive D (USB flash drive).
Welcome to FreeDOS (http://www.freedos.org)!
C:\>d:
D:\>
Backing up the current BIOS
Ensure that the USB flash drive is not write-protected and has at least 1024KB free space
to save the file.
1.
At the FreeDOS prompt, type bupdater /o[filename] and press <Enter>.
D:\>bupdater /oOLDBIOS1.rom
The [filename] is any user-assigned filename with no more than eight alphanumeric
characters for the filename and three alphanumeric characters for the extension.
2.
The BIOS Updater backup screen appears indicating the BIOS backup process. When
BIOS backup is done, press any key to return to the DOS prompt.
ASUSTek BIOS Updater for DOS V1.07
Current ROM
BOARD: P6-P8H61E
VER: 0208
DATE: 10/19/2010
Update ROM
BOARD: Unknown
VER: Unknown
DATE: Unknown
PATH: A:\
BIOS backup is done! Press any key to continue.
Note
Saving BIOS:
ASUS V-Series P8H61E
4-7
Updating the BIOS file
1.
At the FreeDOS prompt, type bupdater /pc /g and press <Enter>.
D:\>bupdater /pc /g
2.
The BIOS Updater screen appears as below.
ASUSTek BIOS Updater for DOS V1.07
Current ROM
BOARD: P6-P8H61E
VER: 0208
DATE: 10/19/2010
Update ROM
BOARD: Unknown
VER: Unknown
DATE: Unknown
PATH: A:\
P8H61E.ROM
A:
4194304 2010-10-19 17:30:48
Note
[Enter] Select or Load
[Up/Down/Home/End] Move
[Tab] Switch
[B] Backup
[V] Drive Info
[Esc] Exit
3.Press <Tab> to switch between screen fields and use the <Up/Down/Home/End>
keys to select the BIOS file and press <Enter>. BIOS Updater checks the selected
BIOS file and prompts you to confirm BIOS update.
Are you sure to update BIOS?
Yes
No
4.Select Yes and press <Enter>. When BIOS update is done, press <ESC> to exit
BIOS Updater. Restart your computer.
DO NOT shut down or reset the system while updating the BIOS to prevent system boot
failure!
4-8
•
For BIOS Updater version 1.04 or later, the utility automatically exits to the DOS
prompt after updating BIOS.
•
Ensure to load the BIOS default settings to ensure system compatibility and stability.
Select the Load Optimized Defaults item under the Exit menu. Refer to section 4.8
Exit menu for details.
•
Ensure to connect all SATA hard disk drives after updating the BIOS file if you have
disconnected them.
Chapter 4: BIOS setup
4.2
BIOS setup program
Use the BIOS Setup program to update the BIOS or configure its parameters. The BIOS
screens include navigation keys and brief online help to guide you in using the BIOS Setup
program.
Entering BIOS Setup at startup
To enter BIOS Setup at startup:
•
Press <Delete> during the Power-On Self-Test (POST). If you do not press <Delete>,
POST continues with its routines.
Entering BIOS Setup after POST
To enter BIOS Setup after POST, do any of the following:
•
Press <Ctrl> + <Alt> + <Delete> simultaneously.
•
Press the reset button on the system chassis.
•
Press the power button to turn the system off then turn it back on. Do this option only if
you failed to enter BIOS Setup using the first two options.
Using the power button, reset button, or the <Ctrl>+<Alt>+<Del> keys to force
reset from a running operating system can cause damage to your data or system. We
recommend to always shut-down the system properly from the operating system.
•
The BIOS setup screens shown in this section are for reference purposes only, and
may not exactly match what you see on your screen.
•
Ensure that a USB mouse is connected to your motherboard if you want to use the
mouse to control the BIOS setup program.
•
The default BIOS settings for this motherboard apply for most conditions to ensure
optimum performance. If the system becomes unstable after changing any BIOS
settings, load the default settings to ensure system compatibility and stability. Select
the Load Default Settings item under the Exit Menu. See section 4.8 Exit Menu.
•
If the system fails to boot after changing any BIOS setting, try to clear the CMOS and
reset the motherboard to the default value. Refer to section 3.4 MemOK! Switch on
how to erase the RTC RAM.
•
The BIOS setup program does not support the bluetooth devices.
BIOS menu screen
The BIOS setup program can be used under two modes: EZ Mode and Advanced Mode.
You can change modes from the Exit menu or from the Exit/Advanced Mode button in the EZ
Mode/Advanced Mode screen.
ASUS V-Series P8H61E
4-9
EZ Mode
By default, the EZ Mode screen appears when you enter the BIOS setup program. The EZ
Mode provides you an overview of the basic system information, and allows you to select
the display language, system performance mode and boot device priority. To access the
Advanced Mode, click Exit/Advanced Mode, then select Advanced Mode.
The default screen for entering the BIOS setup program can be changed. Refer to the
Setup Mode item in section 2.7 Boot menu for details.
Clicks to display all fan
speeds if available
Selects the display language of
the BIOS setup program
Displays the CPU/motherboard temperature,
CPU/5V/3.3V/12V voltage output,
CPU/chassis fan speed
Exits the BIOS setup program without saving
the changes, saves the changes and resets
the system, or enters the Advanced Mode
EFI BIOS Utility - EZ Mode
Exit/Advanced Mode
P8H67-M2/TPM/SI
Friday [10/08/2010]
English
BIOS Version : 0201
Build Date : 03/21/2011
CPU Type : Intel(R) Core(TM) i5-2400 CPU @ 3.10GHz
Speed : 3100 MHz
Total Memory : 1024 MB (DDR3 1333MHz)
Temperature
Voltage
CPU
+113.0ºF/+45.0ºC
CPU
1.248V
5V
MB
+75.2ºF/+40.0ºC
3.3V
3.344V
12V
5.160V
Fan Speed
CPU_FAN
3325RPM
CHA_FAN
N/A
12.248V
Q-Fan Control
Quiet
Performance
Energy Saving
Silent
Boot Priority
Use the mouse to drag or keyboard to navigate to decide the boot priority.
Boot Menu(F8)
Selects the boot device priority
Displays the system properties of the
selected mode on the right hand side
4-10
Silent mode
Default(F5)
Loads optimized default
Standard mode
Turbo mode
Selects the boot device priority
•
The boot device options vary depending on the devices you installed to the system.
•
The Boot Menu(F8) button is available only when the boot device is installed to the
system.
Chapter 4: BIOS setup
Advanced Mode
The Advanced Mode provides advanced options for experienced end-users to configure
the BIOS settings. The figure below shows an example of the Advanced Mode. Refer to the
following sections for the detailed configurations.
To access the EZ Mode, click Exit, then select ASUS EZ Mode.
Back button
Menu bar Pop-up window
General help
EFI BIOS Utility - Advanced Mode
Main
Back
Advanced
Exit
Monitor
Boot
Tool
Advanced\ CPU Configuration >
CPU Configuration
Enabled/Disabled JMB Storage Controller.
Intel(R) Core (TM) i5-2400 CPU 0 @ 3.10GHz
EM64T
Supported
Processor Speed
3100 MHz
Preocessor Stepping
206a6
Microcode Revision
28
L1 Cache
256 KB
L2 Cache
1024 KB
L3 Cache
Intel
Adaptive
Thermal Monitor
Processor Cores
Intel HT Technology
Disabled
CPU Ratio Range
Enabled
CPU Current Ratio
CPU Ratio
Auto
Intel Adaptive Thermal Monitor
Enabled
Active Processor Cores
All
Limit CPUID Maximum
Disabled
Execute Disable Bit
Enabled
Intel Virtualization Technology
Disabled
→←: Select Screen
↑↓: Select Item
Enter: Select
+/-: Change Opt.
F1: General Help
F2: Previous Values
F5: Optimized Defaults
F10: Save ESC: Exit
Version 2.00.1201. Copyright (C) 2011 American Megatrends, Inc.
Configuration fields
Menu items
Scroll bar
Navigation keys
Menu bar
The menu bar on top of the screen has the following main items:
Main
Advanced
For changing the basic system configuration
For changing the advanced system settings
Monitor
For displaying the system temperature, power status, and changing the
Boot
For changing the system boot configuration
Tool
Exit
For configuring options for special functions
For selecting the exit options and loading default settings
ASUS V-Series P8H61E
4-11
Menu items
The highlighted item on the menu bar displays the specific items for that menu. For example,
selecting Main shows the Main menu items.
The other items (Ai Tweaker, Advanced, Monitor, Boot, Tool, and Exit) on the menu bar have
their respective menu items.
Back button
This button appears when entering a submenu. Press <Esc> or use the USB mouse to click
this button to return to the previous menu screen.
Submenu items
A greater than sign (>) before each item on any menu screen means that the item has a
submenu. To display the submenu, select the item and press <Enter> or double-click the
item.
Pop-up window
Select a menu item and press <Enter> to display a pop-up window with the configuration
options for that item.
Scroll bar
A scroll bar appears on the right side of a menu screen when there are items that do not fit on
the screen. Press the Up/Down arrow keys or <Page Up> / <Page Down> keys to display the
other items on the screen.
Navigation keys
At the bottom right corner of the menu screen are the navigation keys for the BIOS setup
program. Use the navigation keys to select items in the menu and change the settings.
General help
At the top right corner of the menu screen is a brief description of the selected item.
Configuration fields
These fields show the values for the menu items. If an item is user-configurable, you can
change the value of the field opposite the item. You cannot select an item that is not
user-configurable.
A configurable field is highlighted when selected. To change the value of a field, select it and
press <Enter> or click on it to display a list of options.
4-12
Chapter 4: BIOS setup
4.3
Main menu
The Main menu screen appears when you enter the Advanced Mode of the BIOS Setup
program. The Main menu provides you an overview of the basic system information, and
allows you to set the system date, time, language, and security settings.
EFI BIOS Utility - Advanced Mode
Main
Advanced
Exit
Monitor
Boot
BIOS Information
BIOS Version
Build Date
ME Version
South Bridge Stepping
0303 x64
02/25/2011
7.0.0.1197
B2 Stepping
CPU Information
Intel(R) Core (TM) i5-2400 CPU 0 @ 3.10GHz
Speed
3100 MHz
Memory Information
Total Memory
Speed
1024 MB
1333 MHz
System Language
System Date
System Time
Access Level
Tool
Choose the system default language
English
[Friday 02/04/2005]
[19:10:20]
Administrator
> Security
4.3.1
System Language [English]
Allows you to choose the BIOS language version from the options. Configuration options:
[English]
4.3.2
System Date [Day xx/xx/xxxx]
Allows you to set the system date.
4.3.3
System Time [xx:xx:xx]
Allows you to set the system time.
4.3.4
Security
The Security menu items allow you to change the system security settings.
•
If you have forgotten your BIOS password, erase the CMOS Real Time Clock (RTC)
RAM to clear the BIOS password. See section 3.3 Jumper for information on how to
erase the RTC RAM.
•
The Administrator or User Password items on top of the screen show the default
Not Installed. After you set a password, these items show Installed.
ASUS V-Series P8H61E
4-13
Administrator Password
If you have set an administrator password, we recommend that you enter the administrator
password for accessing the system. Otherwise, you might be able to see or change only
selected fields in the BIOS setup program.
To set an administrator password:
1.
Select the Administrator Password item and press <Enter>.
2.
From the Create New Password box, key in a password, then press <Enter>.
3.
Confirm the password when prompted.
To change an administrator password:
1.
Select the Administrator Password item and press <Enter>.
2.
From the Enter Current Password box, key in the current password, then press
<Enter>.
3.
From the Create New Password box, key in a new password, then press <Enter>.
4.
Confirm the password when prompted.
To clear the administrator password, follow the same steps as in changing an administrator
password, but press <Enter> when prompted to create/confirm the password. After you clear
the password, the Administrator Password item on top of the screen shows Not Installed.
User Password
If you have set a user password, you must enter the user password for accessing the system.
The User Password item on top of the screen shows the default Not Installed. After you set
a password, this item shows Installed.
To set a user password:
1.
Select the User Password item and press <Enter>.
2.
From the Create New Password box, key in a password, then press <Enter>.
3.
Confirm the password when prompted.
To change a user password:
1.
Select the User Password item and press <Enter>.
2.
From the Enter Current Password box, key in the current password, then press
<Enter>.
3.
From the Create New Password box, key in a new password, then press <Enter>.
4. Confirm the password when prompted.
To clear the user password, follow the same steps as in changing a user password, but press
<Enter> when prompted to create/confirm the password. After you clear the password, the
User Password item on top of the screen shows Not Installed.
4-14
Chapter 4: BIOS setup
4.4
Advanced menu
The Advanced menu items allow you to change the settings for the CPU and other system
devices.
Be cautious when changing the settings of the Advanced menu items. Incorrect field values
can cause the system to malfunction.
EFI BIOS Utility - Advanced Mode
Main
Advanced
Monitor
Exit
Boot
Tool
CPU Configuration Parameters
> CPU Configuration
> System Agent Configuration
> PCH Configuration
> SATA Configuration
> USB Configuration
> Onboard Devices Configuration
> APM
→←: Select Screen
↑↓: Select Item
Enter: Select
+/-: Change Opt.
F1: General Help
F2: Previous Values
F5: Optimized Defaults
F10: Save ESC: Exit
Version 2.00.1201. Copyright (C) 2011 American Megatrends, Inc.
4.4.1
CPU Configuration
The items in this menu show the CPU-related information that the BIOS automatically
detects.
The items shown in the submenu may be different due to the CPU you installed.
ASUS V-Series P8H61E
4-15
CPU Ratio [Auto]
Allows you to set the ratio between the CPU Core Clock and the BCLK Frequency. Use <+>
and <-> keys or the numeric keypad to adjust the ratio. The valid value ranges vary according
to your CPU model.
Intel Adaptive Thermal Monitor [Enabled]
[Enabled]
[Disabled]
Enables the overheated CPU to throttle its clock speed to cool down.
Disables the CPU thermal monitor function.
Active Processor Cores [All]
Allows you to choose the number of CPU cores to activate in each processor package.
Configuration options: [All] [1] [2] [3]
Limit CPUID Maximum [Disabled]
[Enabled]Allows legacy operating systems to boot even without support for CPUs
with extended CPUID functions.
[Disabled]
Disables this function.
Execute Disable Bit [Enabled]
[Enabled]
[Disabled]
Enables the No-Execution Page Protection Technology.
Forces the XD feature flag to always return to zero (0).
Intel(R) Virtualization Technology [Disabled]
[Enabled]Allows a hardware platform to run multiple operating systems separately
and simultaneously, enabling one system to virtually function as several
systems.
[Disabled]
Disables this function.
4.4.2
System Agent Configuration
The System Agent Configuration menu allows you to change the System Agent settings.
Initiate Graphic Adapter [PEG/PCI]
Allows you to decide which graphics controller to use as the primary boot device.
Configuration options: [PCI/PEG] [PEG/PCI]
iGPU Memory [64M]
Allows you to set the Internal Graphics Device share memory size.
Configuration options: [32M] [64M] [96M] [128M]
Render Standby [Enabled]
Allows you to enable or disable Render Standby by Internal Graphics Device.
Configuration options: [Disabled] [Enabled]
iGPU Multi-Monitor [Disabled]
Allows you enable or disable Internal Graphics Device Multi-Monitor Support for add-on VGA
devices. Configuration options: [Enabled] [Disabled]
4-16
Chapter 4: BIOS setup
4.4.3
PCH Configuration
The South Bridge menu allows you to change the PCH settings.
High Precision Timer [Enabled]
Allows you to enable or disable the High Precision Event Timer.
Configuration options: [Enabled] [Disabled]
4.4.4
SATA Configuration
While entering Setup, the BIOS automatically detects the presence of SATA devices. The
SATA Port items show Not Present if no SATA device is installed to the corresponding SATA
port.
SATA Mode [IDE Mode]
Allows you to set the SATA configuration.
[Disabled]
Disables the SATA function.
[IDE Mode]Set to [IDE Mode] when you want to use the Serial ATA hard
disk drives as Parallel ATA physical storage devices.
[AHCI Mode]Set to [AHCI Mode] when you want the SATA hard disk drives
to use the AHCI (Advanced Host Controller Interface). The
AHCI allows the onboard storage driver to enable advanced
Serial ATA features that increases storage performance on
random workloads by allowing the drive to internally optimize
the order of commands.
Serial-ATA Controller 0 [Enhanced]
Allows you to enable or disable the SATA Controller 0. Configuration options: [Disabled]
[Enhanced] [Compatible]
Serial-ATA Controller 1 [Enhanced]
Allows you to enable or disable the SATA Controller 1. Configuration options: [Disabled]
[Enhanced]
S.M.A.R.T. Status Check [Enabled]
S.M.A.R.T. (Self-Monitoring, Analysis and Reporting Technology) is a monitor system. When
read/write of your hard disk errors occur, this feature allows the hard disk to report warning
messages during the POST. Configuration options: [Enabled] [Disabled]
ASUS V-Series P8H61E
4-17
4.4.5
USB Configuration
The items in this menu allow you to change the USB-related features.
The USB Devices item shows the auto-detected values. If no USB device is detected, the
item shows None.
Legacy USB Support [Enabled]
[Enabled]
[Disabled]
Enables the support for USB devices.
The USB devices can be used only for the BIOS setup program.
Legacy USB 3.0 Support [Enabled]
[Enabled]
[Disabled]
Enables the support for USB 3.0 devices.
Disables the function.
EHCI Hand-off [Disabled]
[Enabled]
[Disabled]
4.4.6
Enables the support for operating systems without an EHCI hand‑off
feature.
Disables the function.
Onboard Devices Configuration
HD Audio Controller [Enabled]
[Enabled]
[Disabled]
Enables the High Definition Audio Controller.
Disables the controller.
Reaktek LAN Controller [Enabled]
[Enabled]
[Disabled]
Enables the Realtek LAN controller.
Disables the controller.
Realtek PXE OPROM [Disabled]
This item appears only when you set the Realtek LAN Controller item to [Enabled] and
allows you to enable or disable the Rom Help of the Realtek LAN controller.
Configuration options: [Enabled] [Disabled]
Asmedia USB 3.0 Controller [Enabled]
[Enabled]
[Disabled]
Enables the onboard USB 3.0 controller.
Disables the controller.
The following item appears only when the Asmedia USB 3.0 Controller item is set to
[Enabled].
Asmedia USB 3.0 Battery Charging Support [Enabled]
[Enabled]
[Disabled]
4-18
Enables the Asmedia USB 3.0 battery charging function.
Disables this function
Chapter 4: BIOS setup
4.4.7
APM
Restore AC Power Loss [Power Off]
[Power On]
[Power Off]
[Last State]
The system goes into on state after an AC power loss.
The system goes into off state after an AC power loss.
The system goes into either off or on state, whatever the system state was
before the AC power loss.
Power On By PCIE [Disabled]
[Disabled]Disables the PCIE devices to generate a wake event.
[Enabled]Enables the PCIE devices to generate a wake event.
Power On By RTC [Disabled]
[Disabled]
[Enabled]
4.5
Disables RTC to generate a wake event.
When set to [Enabled], the items RTC Alarm Date (Days) and Hour/Minute/
Second will become user-configurable with set values.
Monitor menu
The Monitor menu displays the system temperature/power status, and allows you to change
the fan settings.
EFI BIOS Utility - Advanced Mode
Main
Advanced
Exit
Monitor
Boot
CPU Temperature
+52ºC / +125ºF
MB Temperature
+38ºC / +100ºF
CPU Fan Speed
Chassis Fan 1 Speed
Tool
CPU Temperature
2129 RPM
N/A
CPU Q-Fan Control
Disabled
Chassis Q-Fan Control
Disabled
CPU Voltage
+1.168 V
3.3V Voltage
+3.296 V
5V Voltage
+5.080 V
12V Voltage
+12.096 V
→←: Select Screen
↑↓: Select Item
Enter: Select
+/-: Change Opt.
F1: General Help
F2: Previous Values
F5: Optimized Defaults
F10: Save ESC: Exit
Version 2.00.1201. Copyright (C) 2011 American Megatrends, Inc.
ASUS V-Series P8H61E
4-19
4.5.1
CPU Temperature / MB Temperature [xxxºC/xxxºF]
The onboard hardware monitor automatically detects and displays the CPU and motherboard
temperatures. Select Ignore if you do not wish to display the detected temperatures.
4.5.2CPU / Chassis / Power Fan Speed [xxxx RPM] or
[Ignore] / [N/A]
The onboard hardware monitor automatically detects and displays the CPU, chassis,
and power fan speeds in rotations per minute (RPM). If the fan is not connected to the
motherboard, the field shows N/A. Select Ignore if you do not wish to display the detected
speed.
4.5.3
[Disabled]
[Enabled]
4.5.4
[Disabled]
[Enabled]
4.5.5
CPU Q-Fan Control [Enabled]
Disables the CPU Q-Fan control feature.
Enables the CPU Q-Fan control feature.
Chassis Q-Fan Control [Enabled]
Disables the Chassis Q-Fan control feature.
Enables the Chassis Q-Fan control feature.
CPU Voltage, 3.3V Voltage, 5V Voltage, 12V Voltage
The onboard hardware monitor automatically detects the voltage output through the onboard
voltage regulators. Select Ignore if you do not want to detect this item.
4-20
Chapter 4: BIOS setup
4.6
Boot menu
The Boot menu items allow you to change the system boot options.
EFI BIOS Utility - Advanced Mode
Main
Advanced
Exit
Monitor
Bootup NumLock State
Full Screen Logo
Option ROM Messages
Boot
On
Tool
Select the keyboard NumLock state
Enabled
Force BIOS
Setup Mode
EZ Mode
Boot Option Priorities
Boot Override
→←: Select Screen
↑↓: Select Item
Enter: Select
+/-: Change Opt.
F1: General Help
F2: Previous Values
F5: Optimized Defaults
F10: Save ESC: Exit
Version 2.00.1201. Copyright (C) 2011 American Megatrends, Inc.
4.6.1
Bootup NumLock State [On]
[On]
[Off]
4.6.2
Sets the power-on state of the NumLock to [On].
Sets the power-on state of the NumLock to [Off].
Full Screen Logo [Enabled]
[Enabled]
[Disabled]
Enables the full screen logo display feature.
Disables the full screen logo display feature.
Set this item to [Enabled] to use the ASUS MyLogo 2™ feature.
4.6.3
Wait for ‘F1’ if Error [Enabled]
When set to [Enabled], the system waits for the F1 key to be pressed when error occurs.
Configuration options: [Disabled] [Enabled]
4.6.4
Option ROM Messages [Force BIOS]
[Force BIOS]
The third-party ROM messages will be forced to display during the boot
sequence.
[Keep Current] The third-party ROM messages will be displayed only if the third-party
manufacturer had set the add-on device to do so.
ASUS V-Series P8H61E
4-21
4.6.5
Setup Mode [EZ Mode]
[Advanced Mode]Sets Advanced Mode as the default screen for entering the BIOS setup
program.
[EZ Mode]
Sets EZ Mode as the default screen for entering the BIOS setup program.
4.6.6
Boot Option Priorities
These items specify the boot device priority sequence from the available devices. The
number of device items that appears on the screen depends on the number of devices
installed in the system.
4.6.7
•
To select the boot device during system startup, press <F8> when ASUS Logo
appears.
•
To access Windows OS in Safe Mode, do any of the following:
- Press <F5> when ASUS Logo appears.
- Press <F8> after POST.
Boot Override
These items specify the boot device priority sequence from the available devices. The
number of device items that appears on the screen depends on the number of devices
installed in the system.
4-22
Chapter 4: BIOS setup
4.7
Tools menu
The Tools menu items allow you to configure options for special functions. Select an item
then press <Enter> to display the submenu.
EFI BIOS Utility - Advanced Mode
Main
Advanced
Monitor
Exit
Boot
> ASUS EZ Flash 2 Utility
Tool
Be used to update BIOS
> ASUS SPD Information
4.7.1
ASUS EZ Flash 2
Allows you to run ASUS EZ Flash 2. When you press <Enter>, a confirmation message
appears. Use the left/right arrow key to select between [Yes] or [No], then press <Enter> to
confirm your choice.
For more details, refer to section 4.1.2 ASUS EZ Flash 2.
4.7.2
ASUS SPD Information
DIMM Slot # [Slot 1]
Displays the Serial Presence Detect (SPD) information of the DIMM module installed on the
selected slot. Configuration options: [Slot 1] [Slot 2]
ASUS V-Series P8H61E
4-23
4.8
Exit menu
The Exit menu items allow you to load the optimal default values for the BIOS items, and
save or discard your changes to the BIOS items. You can access the EZ Mode from the Exit
menu.
Exit
Load Optimized Defaults
Save Changes & Reset
Discard Changes & Exit
ASUS EZ Mode
Launch EFI Shell from filesystem device
Load Optimized Defaults
This option allows you to load the default values for each of the parameters on the Setup
menus. When you select this option or if you press <F5>, a confirmation window appears.
Select Yes to load the default values.
Save Changes & Reset
Once you are finished making your selections, choose this option from the Exit menu to
ensure the values you selected are saved. When you select this option or if you press <F10>,
a confirmation window appears. Select Yes to save changes and exit.
Discard Changes & Exit
This option allows you to exit the Setup program without saving your changes. When you
select this option or if you press <Esc>, a confirmation window appears. Select Yes to
discard changes and exit.
ASUS EZ Mode
This option allows you to enter the EZ Mode screen.
Launch EFI Shell from filesystem device
This option allows you to attempt to launch the EFI Shell application (shellx64.efi) from one of
the available filesystem devices.
4-24
Chapter 4: BIOS setup
ASUS contact information
ASUSTeK COMPUTER INC.
Address
Telephone Fax E-mail
Web site
Technical Support
Telephone Online support
15 Li-Te Road, Peitou, Taipei, Taiwan 11259
+886-2-2894-3447
+886-2-2890-7798
[email protected]
www.asus.com.tw
+86-21-38429911
support.asus.com
ASUS COMPUTER INTERNATIONAL (America)
Address
Telephone Fax
Web site
Technical Support
Telephone Support fax
Online support
800 Corporate Way, Fremont, CA 94539, USA
+1-510-739-3777
+1-510-608-4555
usa.asus.com
+1-812-282-2787
+1-812-284-0883
support.asus.com
ASUS COMPUTER GmbH (Germany and Austria)
Address
Fax
Web site
Online contact
Technical Support
Telephone (Component)
Telephone (System/Notebook/Eee/LCD)
Support Fax
Online support
Harkort Str. 21-23, D-40880 Ratingen, Germany
+49-2102-959911
www.asus.de
www.asus.de/sales
+49-1805-010923*
+49-1805-010920*
+49-2102-9599-11
support.asus.com
* EUR 0.14/minute from a German fixed landline; EUR 0.42/minute from a mobile
phone.
Manufacturer:
ASUSTeK Computer Inc.
Address:
No.150, LI-TE RD., PEITOU, TAIPEI 112,
TAIWAN
Authorised representative in
Europe:
ASUS Computer GmbH
Address:
HARKORT STR. 21-23, 40880 RATINGEN,
GERMANY
ASUS V-Series P8H61E
4-25