Central Station Quick Reference Guide

Central Station Quick Reference Guide
Q u i c k R e fe re n ce G u i d e
Central Station
Note: The DPM4 Quick Reference Guide is not
intended as a replacement to the Operating
Instructions. Prior to operating equipment, the user
must be familiar with the Operating Instructions
Manual contents. This document is a guideline only to
be used as an aid to comprehensive Inservice Training.
P/N: 046-001981-00 Rev A
Table of Contents
Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Admit
a Patient without Patient Information. . . . . . . . . . . . . . 2
Removing
Cleaning
SpOInformation. . . . . . . . . . . . Admit
a Patient
and Plug
Enterfrom
Patient
2
2 Module. . . . . . . . . . . . . . 1
Enabling
SpO2 module. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Dischargethe
a Patient
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
2
Installing
SpO2 patient cable and sensor. . . . . . . . . . . . . . 2
Set a NIBPthe
Interval. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Displaying
the SpO
2
Set Alarm Limits
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 waveform. . . . . . . . . . . . . . . . . . . . . . . . . . . 3
PrintingActive
Real Time
SpO2 Waveform. . . . . . . . . . . . . . . . . . . . . . . 4
3
Silence
Alarm(s). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PatientAll
Alarms. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Pause
Alarms. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Viewing
and
Printing Trends. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Set
Screen
Configuration
(Standard,
Trends,
OxyCRG,
Large Fonts). . . . . . . . . . . . . . . 5
4
Viewing and
Printing
Eventsor. . . . . . . . . . . . . . . . . . . . . . . . . . . . . Change Waveform
4
Disabling
the SpO2Configuration. . . . . . . . . . . . . . . . . . . . . . . . . Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Change Waveform
5
Cleaning
the SpO2 Order. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Module. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Initiate Standby. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Frequently
Asked Questions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Resume Monitoring from Standby. . . . . . . . . . . . . . . . . . . . . . . . 5
Record Real Time Recording Strip . . . . . . . . . . . . . . . . . . . . . . . . 5
Record Trend Table. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Record NIBP Measurements. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Record Alarm Events. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
P/N: 046-001981-00 Rev A
1
Central
Quick Reference
Guide
Station
Admit a Patient without Patient Information
Using Control knob on control panel
• Scroll and select Menu
• Scroll and select Patient Setup
• Select Quick Admit
• Select Yes to confirm clearing prior data and
• Select Patient type (size)
• Select OK to confirm and return to normal screen
Admit a Patient and Enter Patient Information
Using Control knob on control panel
• Scroll and select Menu
• Scroll and select Patient Setup
• Select Admit
• Select Yes to confirm clearing prior data and
• Scroll and select to enter patient information
• Select OK to confirm and return to normal screen
Discharge a Patient
Using Control knob on control panel
• Scroll and select Menu
• Scroll and select Patient Setup
• Select Discharge Patient (Clear Patient Data)
• Select Yes to confirm clearing prior data and return
to normal screen
Note: Clear Patient Data is present if patient
information is omitted.
P/N: 046-001981-00 Rev A
2
Central
Quick Reference
Guide
Station
Set a NIBP Interval
Using Control knob on control panel
• Scroll and select NIBP tile
• Scroll and select Interval
• Scroll to select time
• Scroll and select Exit to return to normal screen
Set Alarm Limits
Using Control knob on control panel (Option 1)
• Scroll and select Parameter tile
• Scroll and select Alm HI/Alm LO
• Scroll to adjust alarm limit
• Scroll and select Exit to return to normal screen
OR
Using Control knob on control panel (Option 2)
• Scroll and select Menu
• Scroll and select System Setup
• Scroll and select Alarm Setup
• Select Alm Sel
• Select parameter’s Alm Setup
• Scroll and select Alm HI/Alm LO
• Scroll to adjust alarm limit
• Scroll and select Exit to return to normal screen
P/N: 046-001981-00 Rev A
3
Central
Quick Reference
Guide
Station
Silence Active Alarm(s)
Press and hold Silence button >2 seconds. If new alarms
occur, system silence will be terminated
Pause All Alarms
Press Silence button. All alarms are paused for a
preconfigured time (1, 2, or 3 minutes). All visual and
audio alarm notification is suspended. Alarm notification
will resume if Silence is pressed a second time or once the
preconfigured time has elapsed.
Set Screen Configuration
(Standard, Trends, OxyCRG, or Large Fonts)
Using Control knob on control panel
• Scroll and select Menu
• Scroll and select System Setup
• Scroll and select Face Select
• Scroll to select screen
• Scroll and select Exit to return to normal screen
Change Waveform Configuration
Using Control knob on control panel
• Scroll and select Menu
• Scroll and select System Setup
• Scroll and select Trace Setup
• Scroll and select waveform(s) to be displayed (A √ in
the waveform box indicates waveform is selected)
P/N: 046-001981-00 Rev A
4
Central
Quick Reference
Guide
Station
Change Waveform Order
Using Control knob on control panel
• Scroll and select Menu
• Scroll and select System Setup
• Scroll and select Trace Setup
• Scroll and select Wave Sequence
• Scroll to select channel to change
• Select parameter
• Scroll and select to Exit to return to normal screen
Initiate Standby
Using Control knob on control panel
• Scroll and select Standby
• Scroll and select Yes to confirm
Resume Monitoring from Standby
Press any key on front panel and Scroll and select Yes
to confirm
Record Real Time Recording Strip
• Select Record key on control panel
• Select Record key to stop (if continuous mode is
enabled)
P/N: 046-001981-00 Rev A
5
Central
Quick Reference
Guide
Station
Record Trend Table
Using Control knob on control panel
• Scroll and select Menu
• Scroll and select Trend Table
• Scroll and select Resolution
• Scroll to adjust time interval
• Scroll and select REC to record
• Scroll and select Exit to return to normal screen
Record NIBP Measurements
Using Control knob on control panel
• Scroll and select Menu
• Scroll and select NIBP Recall
• Scroll and select REC to record
• Scroll and select Exit to return to normal screen
Record Alarm Events
Using Control knob on control panel
• Scroll and select Menu
• Scroll and select Alarm Recall
• Scroll to adjust Start/End time
• Scroll and select Alarm Recall Event to select
sorting criteria
• Scroll and select Alarm Recall to view alarm event
or UP-Down to view other alarm events
• Scroll and select REC to record
• Scroll and select Exit to return to normal screen
P/N: 046-001981-00 Rev A
6
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement