Bard | WA4823 | Specifications | Bard WA4823 Specifications

INSTALLATION INSTRUCTIONS
WALL MOUNTED
PACKAGE AIR CONDITIONERS
MODELS
WA4822
WA4823
WA6022
WA6023
WA602N
Bard Manufacturing Company, Inc.
Bryan, Ohio 43506
Since 1914...Moving ahead just as planned.
Manual :
2100-348D
Supersedes:2100-348C
File:
Volume III Tab 16
Date:05-20-01
CONTENTS
Getting Other Information and Publications............ 1
Wall Mount General Information .............................. 2
Air Conditioning Wall Mount Model Nomenclature.... 2
Shipping Damage...................................................... 6
General .................................................................. 6
Duct Work.................................................................. 6
Condensate Drain ..................................................... 6
Filters
.................................................................. 6
Installation Instructions ............................................ 7
Wall Mounting Information......................................... 7
Mounting the Unit....................................................... 7
Wiring – Main Power................................................ 13
Wiring – Low Voltage Wiring.................................... 13
Figures
Figure 1 Unit Dimensions........................................ 3
WA602N, WA6023, WA4823
Figure 2 Unit Dimensions........................................ 4
WA6022, WA4822
Figure 3 Mounting Instructions................................ 8
WA602N, WA6023, WA4823
Figure 4 Mounting Instructions................................ 9
WA6022, WA4822
Figure 5 Electric Heat Clearance.......................... 10
Figure 6 Wall Mounting Instructions...................... 11
Figure 7 Wall Mounting Instructions...................... 11
Figure 8 Common Wall Mounting Installations...... 12
Figure 9 Unit 24V Terminal Board......................... 14
Figure 10 Fan Blade Setting.................................... 17
Start Up...................................................................... 15
Important Installer Note............................................ 15
Crankcase Heaters.................................................. 15
High Pressure Switch............................................... 15
Three Phase Scroll Compressor Start Up................ 15
Service Hints............................................................ 15
Sequence of Operation............................................ 15
Compressor Control Module.................................... 15
Adjustments............................................................. 16
Phase Monitor.......................................................... 16
Pressure Service Ports............................................ 16
Troubleshooting....................................................... 17
Fan Blade Setting Dimensions................................. 17
Removal of Fan Shroud........................................... 17
Refrigerant Charge.................................................. 17
Pressure Table......................................................... 18
Optional Accessories............................................... 19
Tables
Table 1 Electric Heat Table.................................... 2
Table 2 Electrical Specifications............................ 5
Table 3 Thermostat Wire Size.............................. 13
Table 4 Wall Thermostat and Subbase
Combinations.......................................... 13
Table 5 Fan Blade Dimensions............................ 17
Table 6 Indoor Blower Performance.................... 17
Table 7 Refrigerant Charge.................................. 17
Table 8 Rated CFM and Rated ESP.................... 17
Table 9 Maximum ESP of Operation
Electric Heat Only................................... 18
Table 10 Pressure Table........................................ 18
Table 11 Optional Accessories............................... 19
Getting Other Information and Publications
These publications can help you install the air conditioner
or heat pump. You can usually find these at your local
library or purchase them directly from the publisher. Be
sure to consult current edition of each standard.
For more information, contact these
publishers:
ACCA
Air Conditioning Contractors of America
1712 New Hampshire Ave. N.W.
Washington, DC 20009
Telephone: (202) 483-9370
Fax: (202) 234-4721
ANSI
American National Standards Institute
11 West Street, 13th Floor
New York, NY 10036
Telephone: (212) 642-4900
Fax: (212) 302-1286
National Electrical Code ........................ ANSI/NFPA 70
Standard for the Installation ................... ANSI/NFPA
90A
of Air Conditioning and
Ventilating Systems
Standard for Warm Air .......................... ANSI/NFPA
90B
Heating and Air
Conditioning Systems
Load Calculation for .............................. ACCA Manual J
Residential Winter and
Summer Air Conditioning
Duct Design for Residential ................... ACCA Manual
D Winter and Summer Air Conditioning
and Equipment Selection
ASHRAE American Society of Heating, Refrigerating,
and Air Conditioning Engineers, Inc.
1791 Tullie Circle, N.E.
Atlanta, GA 30329-2305
Telephone: (404) 636-8400
Fax: (404) 321-5478
NFPA
National Fire Protection Association
Batterymarch Park
P.O. Box 9101
Quincy, MA 02269-9901
Telephone: (800) 344-3555
Fax: (617) 984-7057
Manual 2100-348D
Page 3 of 21
WALL MOUNT GENERAL INFORMATION
AIR CONDITIONING WALL MOUNT MODEL NOMENCLATURE
MODEL NUMBER
WA
60
2
3
A
10
X
N
X
X
CAPACITY
60 - 5 Ton
REVISIONS
COLOR OPTIONS
X - Beige (Standard)
1 - White
2 - Mesa Tan
4 - Buckeye Gray
KW
FEATURE CODE
3 - 3 ton air openings
on 5 ton cabinet
2 - 2 ton air openings
on 5 ton cabinet
VOLTS & PHASE
A - 230/208/60/1
B - 230/208/60/3
CONTROL
MODULES
X A
VENTILATION OPTIONS
B - Blank-off Plate
COIL OPTIONS
X - Standard
1 - Phenolic Coated Evaporator
2 - Phenolic Coated Condenser
3 - Phenolic Coated Evaporator
and Condenser
OUTLET OPTIONS
X - Front (Standard)
FILTER OPTIONS
N - No Filter WA4823, WA6023, WA602N models ONLY
X - One Inch Throwaway Filter WA4822, WA6022 models ONLY
W - One Inch Washable Filter WA4822, WA6022 models ONLY
P - Two Inch Pleated Filter WA4822, WA6022 models ONLY
NOTE: All vent options are without exhaust capability. May require separate field supplied barometric relief in building.
Model WA602N is identical to Model WA6023. All references in this
manual to WA6023 apply to WA602N also.
TABLE 1
ELECTRIC HEAT TABLE
Models
WA6023A ONLY
240V-1
WA6023B ONLY
208V-1
240V-1
208V-1
KW
AMPS
B TU H
AMPS
B TU H
AMPS
B TU H
AMPS
B TU H
5.0
20.8
17,050
18.1
12,800
-----
-----
-----
-----
9.0
-----
-----
-----
-----
21.7
30,600
18.7
23,030
10.0
41.6
34,130
36.2
25,600
-----
-----
-----
-----
WA4822A, WA4822B, WA4823A, WA4823B, WA6022A, WA6022B are not
approved for use with electric heat.
Manual 2100-348D
Page
4 of 21
Manual 2100-348D
Page 5 of 21
FIGURE 1
UNIT DIMENSIONS
WA602N, WA6023, WA4823 ONLY
MIS-1348
Manual 2100-348D
Page
6 of 21
FIGURE 2
UNIT DIMENSIONS
WA6022, WA4822 ONLY
MIS-1442
Manual 2100-348D
Page 7 of 21
44
44
55
32
34
44
44
55
32
34
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
WA4823B00, B0Z 230/208-3
WA6022A00, A0Z
A05 230/208-1
A 10
WA6022B00, B0Z
230/208-3
B 09
WA6023A00, A0Z
A05 230/208-1
A 10
WA6023B00, B0Z
230/208-3
B 09
WA602NA00, A0Z
A05 230/208-1
A 10
WA602NB00, B0Z
230/208-3
B 09
45
45
60
60
60
45
45
60
60
60
45
45
60
60
60
35
8
8
8
8
6
10
10
10
10
10
10
10
10
10
10
8
8
6
8
8
10
10
10
10
10
10
10
10
10
8
8
8
8
6
8
8
8
8
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
Minimum
Circuit
Ampacity
3
1
Maximum
External Fuse
or
Ckt. Breaker
2
2
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
Electric Code (latest revision), article 310 for power conductor sizing. CAUTION: When more than one field power
conductor circuit is run through one conduit, the conductors must be derated. Pay special attention to note 8 of
table 310 regarding Ampacity Adjustment Factors when more than 3 conductors are in a raceway.
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
Field Pow er
Ground
Wire Siz e
Wire Siz e
Ground
Wire
CKT A CKT B CKT A CKT B CKT A CKT B CKT A CKT B
Siz e
2
DUAL CIRCUIT
1 Maximum size of the time delay fuse or HACR type circuit breaker for protection of field wiring conductors.
2 Based on 75° C copper wire. All Wiring must conform to NEC and all local codes.
3 These “minimum Circuit Ampacity” values are to be used for sizing the field power conductors. Refer to the National
32
34
44
44
55
26
50
38
1
50
35
WA4823A00, A0Z 230/208-1
2
Maximum
External Field
F u se o r P o w er
Wire
Ckt.
Siz e
Breaker
1
26
1
WA4822B00, B0Z 230/208-3
38
1
WA4822A00, A0Z 230/208-1
Model
Rated
Volts &
P h ase
N o.
Field
Minimum
P o w er
Circuit
Circuits Ampacity
3
SINGLE CIRCUIT
TABLE 2
ELECTRICAL SPECIFICATIONS
SHIPPING DAMAGE
Upon receipt of equipment, the carton should be checked
for external signs of shipping damage. If damage is
found, the receiving party must contact the last carrier
immediately, preferably in writing, requesting inspection
by the carrier’s agent.
GENERAL
The equipment covered in this manual is to be installed
by trained, experienced service and installation
technicians.
The refrigerant system is completely assembled and
charged. All internal wiring is complete.
The unit is designed for use with or without duct work.
Flanges are provided for attaching the supply and return
ducts.
These instructions explain the recommended method to
install the air cooled self-contained unit and the electrical
wiring connections to the unit.
While these instructions are intended as a general
recommended guide, they do not supersede any national
and/or local codes in any way. Authorities having
jurisdiction should be consulted before the installation is
made. See Page 1 for information on codes and
standards.
Size of unit for a proposed installation should be based
on heat loss calculation made according to methods of
Air Conditioning Contractors of America (ACCA). The
air duct should be installed in accordance with the
Standards of the National Fire Protection Association for
the Installation of Air Conditioning and Ventilating
Systems of Other Than Residence Type, NFPA No. 90A,
and Residence Type Warm Air Heating and Air
Conditioning Systems, NFPA No. 90B. Where local
regulations are at a variance with instructions, installer
should adhere to local codes.
Design the duct work according to methods given by the
Air Conditioning Contractors of America (ACCA).
When duct runs through unheated spaces, it should be
insulated with a minimum of one inch of insulation. Use
insulation with a vapor barrier on the outside of the
insulation. Flexible joints should be used to connect the
duct work to the equipment in order to keep the noise
transmission to a minimum.
A 1/4 inch clearance to combustible material for the first
three feet of duct attached to the outlet air frame is
required. See Wall Mounting Instructions and Figures 3
and 3A for further details.
Ducts through the walls must be insulated and all joints
taped or sealed to prevent air or moisture entering the
wall cavity.
Some installations may not require any return air duct. A
metallic return air grille is required with installations not
requiring a return air duct. The spacing between louvers
on the grille shall not be larger than 5/8 inch.
NOTE: If no return air duct is used, applicable
installation codes may limit this cabinet to
installation only in a single story structure.
Any grille that meets with 5/8 inch louver criteria may be
used. It is recommended that Bard Return Air Grille Kit
RG2 through RG5 or RFG2 through RFG5 be installed
when no return duct is used. Contact distributor or
factory for ordering information. If using a return air
filter grille, filters must be of sufficient size to allow a
maximum velocity of 400 fpm.
CONDENSATE DRAIN
A plastic drain hose extends from the drain pan at the top
of the unit down to the unit base. There are openings in
the unit base for the drain hose to pass through. In the
event the drain hose is connected to a drain system of
some type, it must be an open or vented type system to
assure proper drainage.
DUCT WORK
FILTERS
All duct work, supply and return, must be properly sized
for the design air flow requirement of the equipment. Air
Conditioning Contractors of America (ACCA) is an
excellent guide to proper sizing. All duct work or
portions thereof not in the conditioned space should be
properly insulated in order to both conserve energy and
prevent condensation or moisture damage.
WA6022 AND WA4822 ONLY
These instructions and any instructions packaged with
any separate equipment, required to make up the entire
air conditioning system should be carefully read before
beginning the installation. Note particularly any tags and/
or labels attached to the equipment.
Manual 2100-348D
Page
8 of 21
A one inch throw away filter is supplied with each unit.
The filter slides into position making it easy to service.
This filter can be serviced from the outside by removing
the service door. A one inch washable filter and a two
inch pleated filter are also available as optional
accessories. The internal filter brackets are adjustable to
accommodate the two inch filter by bending the metal
tabs holding the 1 inch filter down. There are two tabs
on each side of the filter.
NOTE: WA6023 and WA4823 models require the use of
a return air filter grille.
INSTALLATION INSTRUCTIONS
WALL MOUNTING INFORMATION
1. Two holes for the supply and return air openings must
be cut through the wall as shown in Figure 1 or 2.
Figure 1 is for models WA4823, and WA6023.
Figure 2 is for Models WA4822 and WA6022.
2. On wood frame walls, the wall construction must be
strong and rigid enough to carry the weight of the unit
without transmitting any unit vibration.
WARING
Fire hazard can result if 1/4 inch clearance to
combustible materials for supply air duct is not
maintained. See Figure 3.
3. Concrete block walls must be thoroughly inspected to
insure that they are capable of carrying the weight of
the installed unit.
WA4822 AND WA6022 ONLY
These units are equipped with adjustable return and
supply air flanges. The flanges are adjustable side to side
in 1” increments. This allows these units to be adjusted
so that in side by side applications these units can replace
two 2 Ton units using the same wall openings.
MOUNTING THE UNIT
1. These units are secured by wall mounting brackets
which secure the unit to the outside wall surface at
both sides. A bottom mounting bracket is provided
for ease of installation, but is not required.
WARNING
Failure to provide the 1/4 inch clearance
between the supply duct and a combustible
surface for the first 3 feet of duct can result in
fire causing damage, injury or death.
3. Locate and mark lag bolt locations and bottom
mounting bracket location. See Figure 2.
4. Mount bottom mounting bracket.
5. Hook top rain flashing under back bend of top. Top
rain flashing is shipped secured to the right side of the
back.
6. Position unit in opening and secure with 5/16 lag
bolts; use 7/8 inch diameter flat washers on the lag
bolts.
7. Secure rain flashing to wall and caulk across entire
length of top. See Figure 2.
8. For additional mounting rigidity, the return air and
supply air frames or collars can be drilled and
screwed or welded to the structural wall itself
(depending upon wall construction). Be sure to
observe required clearance if combustible wall.
9. On side by side installations, maintain a minimum of
20 inches clearance on right side to allow access to
control panel and heat strips, and to allow proper
airflow to the outdoor coil. Additional clearance may
be required to meet local or national codes.
2. The unit itself is suitable for 0 inch clearance, but the
supply air duct flange and the first 3 feet of supply air
duct require a minimum of 1/4 inch clearance to
combustible material. If a combustible wall use a
minimum of 30-1/2” x 10-1/2” dimensions for sizing.
However it is generally recommended that a 1 inch
clearance is used for ease of installation and
maintaining the required clearance to combustible
material. The supply air opening would then be 32” x
12”. See Figures 2 and 3 for details.
Manual 2100-348D
Page 9 of 21
Manual 2100-348D
Page
10 of 21
FIGURE 3
MOUNTING INSTRUCTIONS
WA602N, WA6023, WA4823 ONLY
MIS-1349
Manual 2100-348D
Page 11 of 21
FIGURE 4
MOUNTING INSTRUCTIONS
WA6022, WA4822 ONLY
MIS-1444
FIGURE 5
ELECTRIC HEAT CLEARANCE
SIDE SECTION VIEW OF SUPPLY AIR DUCT FOR WALL
MOUNTED UNIT SHOWING 1/4 INCH CLEARANCE TO
COMBUSTIBLE SURFACES.
MIS-277
WARNING
A minimum of 1/4 inch clearance must be maintained between the
supply air duct and combustible materials. This is required for the
first 3 feet of ducting.
It is important to insure that the 1/4 inch minimum spacing is
maintained at all points.
Failure to do this could result in overheating the combustible
material and may result in a fire causing damage, injury or death.
Manual 2100-348D
Page
12 of 21
FIGURE 6
WALL MOUNTING INSTRUCTIONS
SEE FIGURE 3 – MOUNTING INSTRUCTIONS
WALL STRUCTURE
FACTORY SUPPLIED RAIN
FLASHING. MOUNT ON UNIT
BEFORE INSTALLATION
SUPPLY AIR
OPENING
SUPPLY AIR
OPENING
SUPPLY AIR
OPENING
RETURN AIR
OPENING
RETURN AIR
OPENING
RETURN
AIR
OPENING
BOTTOM MOUNTING
BRACKET. MOUNT ON WALL
BEFORE INSTALLING UNIT.
MIS-548
FIGURE 7
WALL MOUNTING INSTRUCTIONS
SEE UNIT DIMENSIONS, FIGURE
1, FOR ACTUAL DIMENSIONS
ATTACH TO TOP
PLATE OF WALL
1.000” CLEARANCE
ALL AROUND
INTERIOR FINISHED WALL
OVER FRAME
SUPPLY DUCT
OPENING
1.000” CLEARANCE
ALL AROUND
RETURN DUCT
OPENING
EXTERIOR FINISHED WALL
OVER FRAME
MIS-549
FRAMING MATERIAL
2 X 4’S, 2 X 6’S AND/OR
STRUCTURAL STEEL
ATTACH TO BOTTOM
PLATE OF WALL
THIS STRUCTURAL MEMBER LOCATED TO MATCH
STUD SPACING FOR REST OF WALL. A SECOND
MEMBER MAY BE REQUIRED FOR SOME WALLS.
Manual 2100-348D
Page 13 of 21
FIGURE 8
COMMON WALL MOUNTING INSTALLATIONS
FREE AIR FLOW NO DUCT
FALSE WALL INSTALLATION
DUCTED SUPPLY RETURN AT UNIT
CLOSET INSTALLATION
MIS-550
Manual 2100-348D
Page
14 of 21
WIRING – MAIN POWER
Refer to the unit rating plate for wire sizing information
and maximum fuse or “HACR” type circuit breaker size.
Each outdoor unit is marked with a “Minimum Circuit
Ampacity”. This means that the field wiring used must be
sized to carry that amount of current. Depending on the
installed KW of electric heat, there may be two field
power circuits required. If this is the case, the unit serial
plate will so indicate. All models are suitable only for
connection with copper wire. Each unit and/or wiring
diagram will be marked “Use Copper Conductors Only”.
These instructions must be adhered to. Refer to the
National Electrical Code (NEC) for complete current
carrying capacity data on the various insulation grades of
wiring material. All wiring muse conform to NEC and all
local codes.
The electrical data lists fuse and wire sizes (75° C
copper) for all models including the most commonly used
heater sizes. Also shown are the number of field power
circuits required for the various models with heaters.
The unit rating plate lists a “Maximum Time Delay Relay
Fuse” or “HACR” type circuit breaker that is to be used
with the equipment. The correct size must be used for
proper circuit protection and also to assure that there will
be no nuisance tripping due to the momentary high
starting current of the compressor motor.
The disconnect access door on this unit may be locked to
prevent unauthorized access to the disconnect. To
convert for the locking capability, bend the tab locate in
the bottom left hand corner of the disconnect opening
under the disconnect access panel straight out. This tab
will now line up with the slot in the door. When shut a
padlock may be placed through the hole in the tab
preventing entry.
See “Start Up” section for important information on three
phase scroll compressor start ups.
WIRING – LOW VOLTAGE WIRING
230 / 208V, 1 phase and 3 phase equipment dual primary
voltage transformers. All equipment leaves the factory
wired on 240V tap. For 208V operation, reconnect from
240V to 208V tap. The acceptable operating voltage
range for the 240 and 208V taps are:
TAP
240
208
RANGE
253 – 216
220 – 187
NOTE: The voltage should be measured at the field
power connection point in the unit and while the
unit is operating at full load (maximum
amperage operating condition).
Five (5) wires should be run from thermostat subbase to
the 24V terminal board in the unit. A five conductor, 18
gauge copper, color-coded thermostat cable is
recommended. The connection points are shown in
Figure 9:
TABLE 3
THERMOSTAT WIRE SIZE
Transformer
VA
55
FLA
Wire Gauge
Maximum
Distance
In Feet
2.3
20 gauge
18 gauge
16 gauge
14 guage
12 guage
45
60
100
160
250
TABLE 4
WALL THERMOSTAT AND SUBBASE COMBINATIONS
T hermostat
8403-002
T87F3111
8403-041
T8034C
Subbase
Predominate Features
8404-003 1 stage heat, 1 stage cool
Q539A1220 System: heat-off-cool Fan: auto-on
---
1 stage heat, 1 stage cool
System: heat-off-cool Fan: auto-on
8403-019
8404-012 1 stage cool, 2 stage heat
T874C1760 Q674A1001 System: heat-auto-cool Fan: auto-on
8403-021
8404-012 2 stage cool, 2 stage heat
T874D1934 Q674A1001 System: heat-auto-cool Fan: auto-on
8403-035
1F95-80
8403-043
CM-200
---
---
2 stage cool, 2 stage heat
Electronic
7 day programming
1 stage heat, 1 stage cool
System: heat-off-cool Fan: auto-on
Manual 2100-348D
Page 15 of 21
FIGURE 9
UNIT 24V TERMINAL BOARD
MIS-1373A
Manual 2100-348D
Page
16 of 21
START UP
IMPORTANT INSTALLER NOTE
For improved start up performance wash the indoor coil
with a dish washing detergent.
CRANKCASE HEATERS
These units are not provided with crankcase heat. These
units utilize scroll compressors which do not require
crankcase heat in this application.
HIGH PRESSURE SWITCH
The models are supplied with a remote reset high
pressure switch. If tripped, this pressure switch may be
reset by turning the thermostat off then back on again.
SERVICE HINTS
1. Caution homeowner to maintain clean air filters at all
times. Also, not to needlessly close off supply and
return air registers. This reduces air flow through the
system, which shortens equipment service life as well
as increasing operating costs.
2. Switching to heating cycle at 75° F or higher outside
temperature may cause a nuisance trip of the remote
reset high pressure switch. Turn thermostat off then
on to reset the high pressure switch.
3. Check all power fuses or circuit breakers to be sure
they are the correct rating.
4. Periodic cleaning of the outdoor coil to permit full
and unrestricted airflow circulation is essential.
SEQUENCE OF OPERATION
THREE PHASE SCROLL COMPRESSOR
START UP INFORMATION
Scroll compressors, like several other types of
compressors, will only compress in one rotational
direction. Direction of rotation is not an issue with single
phase compressors since they will always start and run in
the proper direction.
However, three phase compressors will rotate in either
direction depending upon phasing of the power. Since
there is a 50-50 chance of connecting power in such a
way as to cause rotation in the reverse direction,
verification of proper rotation must be made.
Verification of proper rotation direction is made by
observing that suction pressure drops and discharge
pressure rises when the compressor is energized.
Reverse rotation also results in an elevated sound level
over that with correct rotation, as well as, substantially
reduced current draw compared to tabulated values.
Verification of proper rotation must be made at the time
the equipment is put into service. If improper rotation is
corrected at this time there will be no negative impact on
the durability of the compressor. However, reverse
operation for over one hour may have a negative impact
on the bearing due to oil pump out.
NOTE: If compressor is allowed to run in reverse
rotation for several minutes, the compressor’s
internal protector will trip.
All three phase ZR3 compressors are wired identically
internally. As a result, once the correct phasing is
determined for a specific system or installation,
connecting properly phased power leads to the same
Fusite terminal should maintain proper rotation direction.
COOLING – Circuit R-Y makes at thermostat pulling in
compressor contactor, starting the compressor and
outdoor motor. The G (indoor motor) circuit is
automatically completed on any call for cooling operation
or can be energized by manual fan switch on subbase of
constant air circulation. On all 230 volt units there is a
one minute off delay on the blower motor. 460 volt
models do not have an off delay.
COMPRESSOR CONTROL MODULE
The compressor control module is standard on the models
covered by this manual. The compressor control is an
anti-short cycle/lockout timer with high and low pressure
switch monitoring and alarm relay output.
Adjustable Delay On Make And Break Timer
On initial power up or any time power is interrupted to
the unit the delay on make period begins which will be 2
minutes plus 10% of the delay on break setting. When
the delay on make is complete and the high pressure
switch (and low pressure switch if employed) is closed,
the compressor contactor is energized. Upon shutdown
the delay or break timer starts and prevents restart until
the delay on break and delay on make periods have
expired.
During routine operation of the unit with no power
interruptions the compressor will operate on demand with
no delay.
The direction of rotation of the compressor may be
changed by reversing any two line connections to the
unit.
Manual 2100-348D
Page 17 of 21
High Pressure Switch and Lockout Sequence
ADJUSTMENTS
If the high pressure switch opens, the compressor
contactor will de-energize immediately. The lockout
timer will go into a soft lockout and stay in soft lockout
until the high pressure switch closes and the delay on
break time has expired. If the high pressure switch
opens again in this same operating cycle the unit will
go into manual lockout condition and the alarm relay
circuit will energize. Recycling the wall thermostat
resets the manual lockout.
Adjustable Delay on Make and Delay on Break
Timer
Low Pressure Switch, Bypass, and Lockout
Sequence
If the low pressure switch opens for more than 120
seconds, the compressor contactor will de-energize and
go into a soft lockout. Regardless the state of the low
pressure switch, the contactor will reenergize after the
delay on make time delay has expired. If the low
pressure switch remains open, or opens again for longer
than 120 seconds the unit will go into manual lockout
condition and the alarm relay circuit will energize.
Recycling the wall thermostat resets the manual lockout.
The potentiometer is used to select Delay on Break time
from 30 seconds to 5 minutes. Delay on Make (DOM)
timing on power-up and after power interruptions is equal
to 2 minutes plus 10% of Delay on Break (DOB) setting:
0.5 minute
1.0 minute
2.0 minute
3.0 minute
4.0 minute
5.0 minute
(30 seconds)
(60 seconds)
(120 seconds)
(180 seconds)
(240 seconds)
(300 seconds)
DOB =
DOB =
DOB =
DOB =
DOB =
DOB =
123 second DOM
126 second DOM
132 second DOM
138 second DOM
144 second DOM
150 second DOM
During routine operation of the unit with no power
interruptions the compressor will operate on demand with
no delay.
Typical Settings for Dual Unit Installation:
Unit 1: DOB set at 2 minutes, and DOM is 132 seconds.
Unit 2: DOB set at 4 minutes, and DOM is 144 seconds.
Alarm Relay Output
Alarm terminal is output connection for applications
where alarm relay is employed. This terminal is powered
whenever compressor is locked out due to HPC or LPC
sequences as described.
NOTE: Both high and low pressure switch controls are
inherently automatic reset devices. The high
pressure switch and low pressure switch cut out
and cut in settings are fixed by specific air
conditioner or heat pump unit model. The
lockout features, both soft and manual, are a
function of the Compressor Control Module.
PHASE MONITOR
All units with three phase scroll compressors are
equipped with a 3 phase line monitor to prevent
compressor damage due to phase reversal.
The phase monitor in this unit is equipped with two
LEDs. If the Y signal is present at the phase monitor and
phases are correct the green LED will light.
If phases are reversed, the red fault LED will be lit and
compressor operation is inhibited.
If a fault condition occurs, reverse two of the supply
leads to the unit. Do not reverse any of the unit factory
wires as damage may occur.
PRESSURE SERVICE PORTS
High and low pressure service ports are installed on all
units so that the system operating pressures can be
observed. A pressure table can be found later in the
manual covering all models. It is imperative to match the
correct pressure table to the unit by model number.
Manual 2100-348D
Page
18 of 21
TROUBLESHOOTING
FAN BLADE SETTING DIMENSIONS
REFRIGERANT CHARGE
Shown in Figure 10 is the correct fan blade setting
dimension for proper air delivery across the outdoor coil.
The correct system R-22 charge is shown on the unit
rating plate. Optimum unit performance will occur with a
refrigerant charge resulting in a suction line temperature
(6” from compressor) as shown in Table 7.
Any service work requiring removal or adjustment in the
fan and/or motor area will require that the dimensions
below be checked and blade adjusted in or out on the
motor shaft accordingly.
TABLE 7
REFRIGERANT CHARGE
FIGURE 10
Model
Rated
Airflow
95 OD
82 OD
Temperature Temperature
WA602
1700
53 - 55
60 - 62
WA482
1550
54 - 56
65 - 67
The suction line temperatures in table above are based
upon 80° F dry bulb / 67° F wet bulb (50% R.H.)
temperature and rated airflow across the evaporator
during cooling cycle.
TABLE 5
Model
Dimension
A
WA602N
1.75
TABLE 8
RATED CFM AND ESP
Model
Rated
C FM
ESP
Recommended
Airflow Range
WA602N
1425
0.20
1775 - 1425
j
1. Disconnect all power to the unit.
WA6023
1425
0.20
1775 - 1425
j
2. Remove the screws holding both grilles, one on each
side of unit, and remove grilles.
WA6022
1525
0.20
1850 - 1525
k
WA4823
1350
0.20
1600 - 1350
j
3. Remove screws holding fan shroud to condenser and
bottom. Nine (9) screws.
WA4822
1400
0.20
1700 - 1400
k
REMOVAL OF FAN SHROUD
4. Unwire condenser fan motor.
1 Rated CFM & ESP on High Speed tap with
5. Slide complete motor, fan blade, and shroud assembly
out the left side of the unit.
2 Rated CFM & ESP on High Speed tap with
14 x 28 return air filter grille
20 x 30 filter
6. Service motor/fan as needed.
7. Reverse steps to reinstall.
TABLE 6
INDOOR BLOWER PERFORMANCE
CFM @ 230V
WA602N
WA6023
WA6022
WA4823
WA4822
High Speed
High Speed
High Speed
High Speed
E.S.P.
In H2O
Dry
Coil
Wet
Coil
Dry
Coil
Wet
Coil
Dry
Coil
Wet
Coil
Dry
Coil
Wet
Coil
.0
.1
.2
1775
1675
1575
1600
1525
1425
1850
1755
1700
1675
16001525
1600
1525
1425
1525
1425
1350
1700
1600
1475
1625
1525
1400
Manual 2100-348D
Page 19 of 21
TABLE 9
MAXIMUM ESP OF OPERATION
ELECTRIC HEAT ONLY
MODELS
ESP
A 05
A 10
B 09
WA6023 - ONLY
.4
.3
.3
Values shown are for units equipped with
standard 1” throwaway filters or 1” washable
filters. Derate ESP by .15 for 2” pleated filters.
TABLE 10
PRESSURE TABLE
COOLING
Model
Air Temperature Entering Outdoor Coil °F
Return Air
Temperature
Pressure
75
80
85
90
95
75 deg. D B
62 deg. WB
Low S i de
High Side
71
233
72
247
74
262
75
278
76
295
77
313
78
331
78
351
79
371
80 deg. D B
67 deg. WB
Low S i de
High Side
76
237
78
253
79
269
80
285
81
303
82
321
83
340
84
360
85
381
85 deg. D B
72 deg. WB
Low S i de
High Side
84
245
85
261
85
278
86
296
87
314
88
333
89
353
90
373
91
394
75 deg. D B
62 deg. WB
Low S i de
High Side
73
204
74
217
76
232
78
248
79
265
80
284
82
304
83
325
84
348
80 deg. D B
67 deg. WB
Low S i de
High Side
78
210
79
223
81
238
82
254
84
272
86
291
87
312
89
334
90
357
85 deg. D B
72 deg. WB
Low S i de
High Side
84
217
85
231
87
247
88
264
90
282
92
302
93
323
95
345
97
369
WA602
WA482
100
105
110
115
Low side pressure ± 2 PSIG
High side pressure ± 5 PSIG
Tables are based upon rated CFM (airflow) across the evaporator coil. If there is any doubt as to correct
operating charge being in the system, the charge should be removed, system evacuated and recharged to
serial plate instructions.
Manual 2100-348D
Page
20 of 21
CMC-15
Start Kit
X
WMCB-09A
WMCB-07B
WMCB-08A
WMCB-05B
Circuit Breaker Kit
Circuit Breaker Kit
Circuit Breaker Kit
Circuit Breaker Kit
X
WA4823B, WA4822B
Description
WA4823A, WA4822A
Part
Number
WA6023B, WA6022B
WA6023A. WA6022A
TABLE 11
OPTIONAL ACCESSORIES
X
X
X
X
Manual 2100-348D
Page 21 of 21
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising