DG 900
Before you read anything else, please observe the following:
Warning!
Uniden Australia Pty. Ltd DOES NOT represent this unit to be waterproof.
To reduce the risk of fire, electrical shock or damage to the unit, DO
NOT expose this unit to rain or moisture.
Rechargeable Nickel-Cadmium battery Warning
This equipment contains a rechargeable nickel-cadmium battery.
The rechargeable nickel-cadmium battery contained in this
equipment may explode if disposed of in a fire.
Do not short-circuit the battery.
Do not charge the rechargeable nickel-cadmium battery used in this
equipment in any charger other than the one designed to charge
this battery as specified in the owner's
owner'smanual. Using another
charger may damage the battery or cause the battery to explode.
!
The exclamation point is intended to alert the
user to the presence of important operating and
maintenance (servicing) instructions in
the literature accompanying the appliance.
When using your telephone equipment, these basic safety precautions
should always be followed to reduce the risk of fire, electrical shock
and injury to persons:
Read and understand all instructions:
Follow all warnings and instructions marked on the product.
Unplug this product from the wall outlet before cleaning.Use a
dry cloth for cleaning without liquid or aerosol cleaners.
Do not use this product near water; for example, near a bath tub,
wash bowl, kitchen sink or laundry tub, in a wet basement, or near
a swimming pool.
5. Do not place this product on an unstable cart, stand or table.
The telephone may fall, causing serious damage to the unit.
6. Slots and openings in the cabinet and the back or bottom are
provided for ventilation. To protect the product from overheating,
these openings must not be blocked or covered. This product
should never be placed near or over a radiator or heat register.
This product should not be placed in a built-in installation unless
proper ventilation is provided.
This product should be operated only from the type of power source
indicated on the marking label. If you are not sure of the type of
power supply to your home, consult your dealer or local power
company.
Do not allow anything to rest on the power cord. Do not locate this
product where the cord will be damaged by persons walking on it.
Do not overload wall outlets and extension cords, as this can result
in the risk of fire or electrical shock.
10. Never push objects of any kind into this product through cabinet
slots, as they may touch dangerous voltage points or sort out parts
that could result in a risk of fire or electric shock.
Never spill liquid of any kind on the product.
11. To reduce the risk of electric shock, do not disassemble this
product. Take it to qualified service personnel when service or
repair work is required, Opening or removing covers may expose
you to dangerous voltages or other risks. Incorrect reassemblycan
cause electric shock when the appliance is subsequently used.
3
12. Unplug this product from the wall outlet and refer servicing to
qualified service personnel under the following conditions:
When the power supply cord is damaged or frayed.
A.
B.
If liquid has been spilled into the product.
If the product has been exposed to rain or water.
C.
D. If the product does not operate normally when following the
operating instructions. (Adjust only those controls that are
covered by the operating instructions, improper adjustment
of other controls may result in damage and will often require
extensive repair work by a qualified technician).
E.
If the product has been dropped or the cabinet has been
damaged.
If the product exhibits a distinct change in performance.
E
13. Do not use the telephone to report a gas leak in the vicinity of the
leak.
Additional Battery Safety Precautions
Caution! To reduce the risk of fire or injury to persons by the battery,
read and follow these instructions:
Use only the appropriate type and size battery pack specified in the
owner’s manual.
Do not dispose of the battery pack in a fire. The cell may explode.
Do not open or mutilate the battery pack. Released electrolyte is
corrosive and may cause damage to the eyes or skin. It may be
toxic if swallowed.
4. Exercise care in handling the battery in order not to short the
battery with conducting materials such as rings, bracelets and keys.
The battery or conductor may overheat and cause bums.
5. Charge the battery pack provided with or identified for use with this
product only in accordance with the instructions and limitations.
6. Observe proper polarity orientation between the battery pack and
battery charger.
Unplug all electrical appliances when you know an electrical storm is
approaching. Lightning can pass through your household wiring and
damage any device connected to it. This phone is no exception.
Warning!
Please do not attempt to unplug any appliance during an electrical
storm.
Your new phone is designed to achieve the maximum possible range by
transmitting and receiving according to the highest specifications. We
have rated this phone to operate at a maximum distance with the
qualification that the range depends upon the environment in which
the telephone is used. Many factors limit range, and it would be
impossible to include all the variables in our rating. The Maximum
Range rating of this phone is meant to be used as a means of
comparison against other range claims.
Telephone Line Problems
If you are having trouble with your telephone service, you must first
disconnect your phone to determine if it is the cause of your problem
If you determine that it is the cause, you must leave it disconnected
until the trouble has been corrected.
Radio Interference
Radio interference may occasionally cause buzzing and humming in
your cordless handset, or clicking noises in the base. This interference
is caused by external sources such asTV,refrigerator, vacuum cleaner,
fluorescent lighting or electrical storm. Your unit is NOT DEFECTIVE.
If these noises continue and are too distracting, please check around
5
your home to see what appliances may be causing the problem. In
addition, we recommend that the base not be plugged into a circuit
that also powers a major appliance because of the potential for
interference. Be certain that the antenna on the unit is raised
vertically.
In the unlikely event that you consistently hear other voices or
distracting transmissions on your phone, you may be receiving radio
signals from another cordless telephone or other source of interference.
If you cannot eliminate this type of interference, you need to change to
a different channel.
To get the most from your
phone, please read this
owner’smanualthoroughly.
Also be sure to complete and
mail the product registration
form.
Base
Handset
Finally, it should be noted that some cordless telephones operate at
frequencies that may cause interference to nearby TV’s or VCR's To
minimise or prevent such interference, the base of the cordless
telephone should not be placed near or on top of a TV or VCR. If
interference is experienced, moving the cordless telephone farther away
from the TV or VCR will often reduce or eliminate the interference.
BT900
RechargeableBattery
AAD-650U
AC adapter
Beltclip
If any of these items are
missing or damaged,
contact your place of
purchase.
Telephone Cord/Plug
Desktop/ Wall Mount
Adaptor
screws
The beltclip is attached to
the bottom of the base.
This Owner’s Manual
l Registration Card
l Quick Start Guide and Other Printed Materials
l
7
Selecting a Location
Before choosing a location for your new phone, there are some
important guidelines you should consider:
The location shoud be close to both a phone jack and an AC power
outlet.
Keep the base and handset away from sources of electrical noise
such as motors or fluorescent lighting.
Be sure there is sufficient space to raise the base antenna vertically.
The base can be placed on a desk or tabletop or mounted on a
wall plate.
Your should charge your new phone for 15-20 hours before
completing the installation or using the handset.
Most phone equipment available now uses modular jacks. Phone cords
are fitted with a molded plastic connector which plugs into this type of
jack. If you do not have modular phone jacks, contact your local
telephone company for information about their installation.
Connecting the Telephone Cords
Consider these safety guidelines before connecting the telephone cords
Caution!
l
Never install telephone wiring during a lightning storm.
l
Never touch uninsulated telephone wires or terminals unless the
telephone line has been disconnected.
l
Use caution when installing or modifying telephone lines.
Applying Power to the Base
This phone requires an uninterrupted AC outlet and the included AC
adapter. To relieve strain on the DC plug when the phone is placed on a
desk or table, wrap the power cord around the strain relief notch on the
bottom of the base.
Use only the Uniden AC Adapter supplied with this phone.
AAD 650U Approval Number N14700
Output: 9V 350mA Input: 230~240V AC 50Hz
8
Before choosing a location
for your phone, read the
“Installation Considerations
“Precautions and Important
Safety Instructions” in the
beginning of this manual
AC
Adapter
1) Plug the AC adapter cord into the 9V DC input jack on the back of
the base.
2) Wrap the AC adapter cord around the strain relief notch.
!
Place the power cord so that it does not create a trip
hazard or where it could become chafed and create a
fire or electrical hazard.
3) Plug the AC adapter into a standard 240V AC wall outlet.
!
4) Charge the battery (refer to “Charging the Battery Pack,” page 16).
5) Plug one end of the telephone cord into the TEL LINE jack on
the back of the base.
6) Plug the other end of the cord into your telephone jack on the wall.
9
!
) Attach the desktop stand to the base.
Before you plug the other
end of the telephone cord
into the modular jack on
the wall, charge the
battery (refer to “Charging
the Battery Pack,” page
16).
Before using your phone,
fully charge the Nickel
Cadmium battery pack for
15-20hours.
) Set the base on a desk ortabletop
and place the handset into the base as
shown Then, raise the antenna to a
verticle position.
!
Place the power cord so
that it does not create a
trip hazard or where it
could become chafed and
create a fire or electrical
hazard.
5) Plug one end of the short telephone
cord (not supplied) into the
TEL LINE jack on the back of the
base, then plug the other end
into a standard telephone jack.
▼ Standard wall plate mounting
This phone can be mounted on any standard wall plate.
Line up the mounting slots on the base
with the mounting posts on the wall,
then push in and down until the
phone is firmly seated.
1) Remove the wall mount adapter
from the notches at the top of
the base.
.
2) Rotate the wall mount adapter
180 degrees and snap it into place
at the bottom of the base.
10
4) Put the AC adapter cord inside the
molded wiring channel, then wrap it
around the strain relief notch. Plug
the AC adapter into a standard
240V AC wall outlet.
On the base unit, pull the handset
retainer out of the slot and rotate
it clockwise 180 degrees.
?\
!U
2) Remove the wall mount adapter
from the notches at the top of
the base.
8) Flip the retainer from front to back,
then slide it into the slot so that the
lip of the retainer faces up and the
oval is at the bottom of the retainer.
This will hold the handset in place.
V Direct wall mounting
If you don’t have a standard wall plate, you can mount your phone
directly to the wall, Before doing this, consider the following:
Select a location away from electrical cables, pipes, or other items
behind the mounting location. Inserting screws into areas such as
this can be hazardous.
Try to mount your phone closer to a working phone
jack in order to avoid excessive cord lengths. Remember, you are
not mounting to a wall plate with a built in phone jack.
If the selected mounting area has no wooden support beams directly
behind it, you will need the appropriate anchoring devices in order
for the wall to properly support your phone.
Insert two mounting screws into
the wall, with their appropriate
anchoring device if necessary,
100mm apart. Allow about
5mm between the wall
and screwheads for mounting
the phone.
12
3) Rotate the wall mount adapter
180 degrees and snap it into place
at the bottom of the base.
4) Plug the AC adapter into the base.
TOP
5) Put the AC adapter cord inside the
molded wiring channel, then wrap it
around the strain relief notch. Plug
the AC adapter into a standard
240V AC wall outlet.
,
13
Plug one end of the telephone
cord into the TEL LINE jack on
the back of the base, then plug
the other end into a standard
telephone jack.
!
Use only Uniden battery
model BT-900 supplied
with your phone.
Line up the mounting slots on the base
with the mounting screws on the wall,
then push in and down until the
phone is firmly seated.
1) Press in on the battery cover release
and slide the cover down until it
comes off.
2) Install the nickel-cadmium battery
with the label facing down.
3) Slide the battery cover on until it snaps into place.
On the base unit, pull the handset
retainer out of the slot and rotate
it clockwise 180 degrees.
Flip the retainer from front to back,
then slide it into the slot so that the
lip of the retainer faces up and the
oval is at the bottom of the retainer.
This will hold the handset in place.
+
I/\
JTJi-5 1
1 j
I/
14
15
▼
!
Please visit your
authorised Uniden dealer
to obtain an extra battery
pack.
▼ Initial battery charging
Before plugging the phone line into your new phone for the first time,
fully charge the rechargeable battery pack for 15-20 hours
without interruption.
1) Place the handset on the base.
2) Make sure that status LED lights. If the LED doesn’t light, check to
see that the AC adapter is plugged in and that the handset makes good
contact with the base charging contacts,
Low battery indicator
The low battery indicator shows when
the battery needs to be re-charged. If
the phone is not in use, the talk/batt
low LED flashes every three seconds. If
the phone is in use, the talk/batt low
LED flashes every three seconds and
the handset beeps. Complete your
conversation as quickly as possible and
return the handset to the base for
charging.
▼ Charging optional battery packs
The base unit of your phone is equipped with a compartment for
charging an extra battery pack for use in your handset. You can
obtain an extra battery pack from your authorized Uniden dealer.
1) Position the battery pack so the inner side with contacts is facing up.
Slide the battery pack into the
charging compartment until it
clicks into place. The compartment
has a latch that keeps the battery
in place.
To maintain a good charge, clean all charging contacts on the handset
and base about once a month with a pencil eraser or other contact
cleaner. DO NOT use liquids or solvents; you may damage your phone.
To locate the handset (while it’s
off the base), press page on the
base. The handset beeps for
about 15 seconds.
Fully charge the battery for 15-20 hours.
When charging is complete, pull up on the latch to remove the
battery pack To install the charged battery into the handset,
refer to “Installing the Handset Battery Pack,” page 15.
A
16
”
ti
*
”
In the event of a power failure your spare battery pack
can be used as a back-up power supply for the base unit
17
!
Be sure the PULSE/TONE switch is in
the TONE position unless your local
phone system uses pulse dialing
V
To attach the beltclip
1) Remove the slot cover.
Most phone systems use
tone dialing. Check with
your local phone company
if you’re not sure whether
your system is
tone or pulse.
2) Put the beltclip in the slot and press
down until it clicks.
▼ handset ringer volume
When the phone is either charging or in standby mode, pressing the
vol ▲ or V key on the handset selects the handset ringer volume.
There are two ringer volume settings; high and low.
V Handset earpiece volume
There are four volume settings for the handset earpiece;max high,
medium, and low. The handset earpiece volume can only be adjusted
during a call. To lower the volume, press vol ▲ To raise the volume,
press vol ▼
V To remove the beltclip
1) Pull back on the release tab and
pull the beltclip up.
2) Replace the slot cover. You can
store either the beltclip
or slot cover on the
bottom of the base.
1. Press flash LED flashes.
2. Press 1, 2,3 or 4 on the keypad to select ringer tone.
18
19
Use only the Uniden HS910
or CTA630 headset.
Your phone may be used with optional
headset, the Uniden HS 910, or Uniden
CTA 630
To use this feature, simply insert the
headset plug into the headset jack.
Your headset is ready for hands-free
conversations.
To answer
Pick up the handset.
Press any button.
a call
Keep headset wire away
from base antenna.
To prevent other parties from making unauthorized calls on your
phone line, a digital code was added to the DG900 Your phone’s
handset and base share this code, which is randomly set each time you
place the handset in the charging cradle.
V
To reestablish communication between the handset and the
base in the event of a power failure
1) Restore power to the base.
1) Pick up the handset.
2) Press talk
To make a call
3) Listen for the dial tone.
4) Dial the number.
1) Press talk
2) Listen for dial the tone.
3) Dial the number.
Press talk or return the handset to the
To hang up
base (AutoStandby).
L_
To redial
1) Pick up the handset.
2) Press talk
3) Listen for the dial tone.
4) Press redial
1) Press talk
2) Listen for the dial tone.
3) Press redial
2) Place the handset on the base. The digital security code is reset.
If you are using an optional
headset, you must still use
the handset keypad for
phone operations.
If you have “call waiting” service
and a call waiting tone sounds
while you are on a call, press
flash then 2 to accept the waiting
call. There is a short pause, then
you will hear the new caller. To
return to the original caller,
press flash then 1.
~~~~~~~~~~~~~~~~~~~~~~~;
p the current call and picks up the incoming call or
20
21
Press the vol ▲ orv key on the handset to increase or decrease
volume while on a call. Volume will remain on the same setting when
you hang up.
On certain occasions after dialing a number, you may be requested to
enter an access code, such as your account number. Youcan enter this
number into a memory location for later use by doing the following.
1) Store the access code into one of the memory locations
(01-20) or press memory key a, b, c or d following steps 1-5
above.
Lift the handset from the base.
Press mem. The talk/batt low LED blinks.
Enter the phone number, up to 16 digits. If a pause is needed
during dialing to access a long distance service, press redial/p
Press mem again.
Enter the memory location (01-20) on the keypad or press
memory key a, b, c or d A tone indicates that the number is stored.
The pause button counts
as one digit. Pressing
redial/p on the handset,
more than once increases
the length of pause
between numbers.
V
2) Dial the party or service main number.
3) When you need to enter the special number, press mem followed by
the memory location (01-20) or press memory key a, b, c or d
To use the mute feature during a conversation, press mute The other
party will not be able to hear you although you can hear them. To
disable the mute feature, press mute again.
Using the memory location features
1) Press talk
2) Press mem.
Accidentally pressing
memory keys a, b, c or d
may result in
unintentional dialing.
As you begin to move too far from your base unit, you will first hear a
clicking sound. As you travel further out-of-range, the voice
transmission will begin to break up. If you pass the range limits of the
base unit, your call will terminate.
3) Enter the memory location (01-20) on the
keypad. The number automatically dials.
V One-touch memory dialing
Press a one-touch memory key a, b, c or d. The number
automatically dials.
erase procedure will be
cancelled if more than 30
seconds elapse behveen
each keystroke.
22
1) Remove the handset from the base unit.
2) Press the mem button twice.
3) Press the memory location (01-20) or
press memory key a, b, c, or d to be
erased. A tone indicates that the stored
number is erased from memory.
23
If your phone is not performing to your expectations, please try these
simple steps before calling Uniden customer service.
The redial key redials the last number dialed
The redialed number can be up to 32 digits long.
PROBLEM
SUGGESTION
The charge light won’t come
Make sure the AC adapter is
plugged into the base and
wall outlet.
l Make sure the handset is properly
seated in base.
l Make sure the charging contacts on
the handset and base are clean.
on when the handset is placed
on the base.
If you are dialing in the pulse mode
and need to enter tone digits, press
tone to enter the digits. Once the call
has ended, the tone mode is cancelled
and pulse dialing resumes.
The audio sounds weak
and/or scratchy.
Can't make or receive calls.
The DG900 DGMax telephone may work with a 2-wire Analogue PABX
network. However, with the DG900 hook-flash timing fixed at
100 msec, some PABX equipment that uses a different hook flash
timing may have it’s special feature (placing call on hold or
transferring call, etc...) inaccessible.
~~~~,~~,,,~~,~~~~~~~~,”
Check with your PABX supplier if you are not sure whether
your PABX network uses Analogue or Digital interface.
24
-
l
Make sure that the base antenna is
in a vertical position.
l Move the handset and/or base to a
different location away from metal
objects or appliances and
try again.
l
Check both ends of the base
telephone line cord.
l Make sure the AC adapter is
plugged into the base and
wall outlet.
l Disconnect the AC adapter for a
few minutes, then reconnect it.
l Place the handset back on the
charging cradle for a few seconds.
The status LED will blink
indicating that the phone has
been reset.
l
__
PROBLEM
_---~
The handset doesn’t ring or
receive a page.
““____...
SUGGESTION
I
The Nickel-Cadmium battery pack
may be weak. Charge the battery
on the base unit for 15-20 hours.
l The handset may be too far away
from the base unit.
l Place the base unit away from
appliances or metal objects.
l Place the handset back on the
charging cradle for a few seconds.
The status LED will blink
indicating that the phone has
been reset.
l
The DG900 DGMax complies with TS001, TSO02, TSO04, AS/NZ3260 and
FCC Parts 15 and 68 (as per ACA Radio Communications Class Licensing
requirements).
Frequency control: PLL
Modulation: Direct Sequence Spread Spectrum; DBPSK
Operating temperature: -10˚ to +50˚ C
Frequency: 917.4 to 925.8 MHz (15 channels)
Power requirements: 9V 350 mA (from AC adapter)
Size: 139.7mm.(W) x 95.25mm (D) x 254mm (H)
Weight: Approx. 504.62g (including optional battery)
Battery:
BT-900 (as backup)
Capacity
600 mAH 3.6V
Talk mode
2 hours
Standby mode
4 hours
Frequency: 917.4 to 9258 MHz (15 channels)
Power requirements: Rechargeable Nickel Cadmium battery pack
Size (without antenna): 57.15mm (W) x 88.9mm (D) x 184.15mm(H)
Weight: Approx. 263.65g (including battery)
Battery:
BT-900
Capacity
600 mAH, 3.6V
Talk mode
4 hours
Standby mode
7 days
Specifications, features, and availability of optional accessories are
all subject to change without prior notice.
26
27
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement