U-Line | CLR2160 | Installation guide | U-Line CLR2160 Installation guide

U-Line CLR2160 Installation guide
Installation Guide
CLR2160 — Clear Ice Maker
CLRCO2175 Combo®—
Clear Ice Maker/Refrigerator
www.U-LineService.com
Phone (414) 354-0300 • FAX (414) 354-7905
Service & Parts Tech Lines Phone (800) 779-2547 • FAX (414) 354-5696
OnlineService@U-Line.com
©2007 U-Line Corporation
05/2007
CLR2160/CLRCO2175 Ice Makers
Contents
Exterior Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Cut-Out Dimensions CLR2160 . . . . . . . . . . . . . . . . . . . .
Product Dimensions CLR2160 . . . . . . . . . . . . . . . . . . . .
Door Swing/Clearances Information CLR2160 . . . . . . .
Cut-Out Dimensions CLRCO2175 . . . . . . . . . . . . . . . . .
Product Dimensions CLRCO2175 . . . . . . . . . . . . . . . . . .
Door Swing/Clearances Information CLRCO2175 . . . .
Reversing the Door. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Other Site Requirements . . . . . . . . . . . . . . . . . . . . . . . .
Side-By-Side Installation Instructions CLR2160 . . . . . .
Side-By-Side Installation Instructions CLRCO2175 . . . .
Custom 1/4'' Door Panel Insert . . . . . . . . . . . . . . . . . . .
Full Overlay Door Panel . . . . . . . . . . . . . . . . . . . . . . . . .
Checking Door Alignment . . . . . . . . . . . . . . . . . . . . . .
Adjusting Door Alignment . . . . . . . . . . . . . . . . . . . . . .
Water Supply Connection . . . . . . . . . . . . . . . . . . . . . . .
Drain Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Final Water/Drain Connection: . . . . . . . . . . . . . . . . . . .
Electrical Specifications . . . . . . . . . . . . . . . . . . . . . . . . .
Leveling Information . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installation Tip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installation of the CLR2160 . . . . . . . . . . . . . . . . . . . . . .
Installation of the CLRCO2175 . . . . . . . . . . . . . . . . . . .
Relocating the Shelves (CLRCO2175) . . . . . . . . . . . . . .
Installation Troubleshooting . . . . . . . . . . . . . . . . . . . . .
Initial Start-Up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Start-Up Troubleshooting . . . . . . . . . . . . . . . . . . . . . . .
Service Information . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1 Follow Safety Precautions
4
5
5
5
6
6
6
7
8
8
9
9
10
14
14
15
15
18
20
20
21
21
21
22
22
23
24
24
IMPORTANT
PLEASE READ all instructions completely before
attempting to install or operate the unit.
• This unit requires connection to the water supply.
Improper hook-up can result in substantial property
damage! If you are unsure of your ability to safely
connect the water supply to the unit, consult a licensed
plumber for assistance.
• This unit requires connection to a drain. Improper
connection can result in substantial property damage!
If you are unsure of your ability to safely connect the
unit to a drain, consult a licensed plumber for
assistance.
• This unit requires connection to a grounded (threeprong), polarized receptacle that has been placed by a
qualified electrician in accordance with applicable
electrical codes.
Safety Alert Definitions
Safety items throughout this guide are labeled with a
Danger, Warning or Caution based on the risk type:
DANGER
Danger means that failure to follow this safety
statement will result in severe personal injury or
death.
WARNING
Warning means that failure to follow this safety
statement could result in serious personal injury,
or death.
CAUTION
Caution means that failure to follow this safety statement
may result in minor or moderate personal injury, property
or equipment damage.
www.U-LineService.com
2
05/2007
CLR2160/CLRCO2175 Ice Makers
General Precautions
2 Inspect and Plan
Use this appliance for its intended purpose only and
follow these general precautions along with those listed
throughout this guide:
You have received a carton containing your CLR2160 Ice
Maker or CLRCO2175 Clear Ice Maker/Refrigerator with
a package inside containing a Use and Care Guide, a
Drain and Water Installation Instruction sheet, a Product
Registration Card and water connection parts. Complete
and mail the Product Registration Card or register
online at www.U-LineService.com. Once your unit is
installed, keep the Use and Care Guide and this
Installation Guide in a safe place for future reference.
WARNING
SHOCK HAZARD — Electrical Grounding Required.
• Keep the unit unplugged throughout installation
except during testing.
• Never remove the round grounding prong from
the plug and never use a two-prong grounding
adapter.
Your unit is Black, White or Stainless Steel. Black and
White units have a reversible door with a slightly
contoured handle across the top. They come with a flush
mounted door panel that, when removed, will accept a
custom 1/4-inch thick door panel or a 3/4-inch thick full
overlay door panel. Stainless Steel units are covered with
a protective coating and have been ordered left- or righthand hinged. The Stainless doors are not reversible and
do not accept custom panels. CLR2160 Ice Makers/
CLRCO2175 Clear Ice Maker/Refrigerators may be ordered
with or without a factory-installed drain pump. Please
carefully follow the directions that apply to your unit and
your intended design.
• Never use an extension cord to connect power to
the unit.
• Always keep your working area dry.
CAUTION
• Use care when moving and handling the unit. Use
gloves to prevent personal injury from sharp edges.
• Do not lift the unit by the door or door handle.
• Do not install the unit behind closed doors or in any
way that would obstruct airflow to the front grille,
which may cause the unit to malfunction.
Tools/Materials Required
• Screwdrivers — slotted and Phillips head
• 1/4” Nut driver (optional)
• Slide cutter
• Copper tubing cutter
• 12” Level
• 9/16” Open end wrench
• 7/16” Open end wrench
• Pliers
• (1) Brass garden hose fitting (supplied with product)
• (10’ or more depending on water supply location) 1/4”
O.D. soft copper tubing
• *(10’ or more depending on drain location) 5/8” I.D. braid
reinforced PVC drain tubing
• *(3) 11/16” to 1 1/4” Clamp range worm drive hose clamps
• *(1) Nylon barbed coupling for 5/8” I.D. hose
• *(1) 5/8” to 7/8” adapter (optional)
• P60 Drain Pump (if required and not already factory
installed, see Page 17)
• 1/4-inch thick door panel material and cutting tools
(Black or White units) (If installing a 1/4”Panel)
• Full Overlay Door Panel Kit (part number U-OL2175B —
Black or part number U-OL2175W — White), 3/4-inch door
panel overlay, cutting tools, drill and bits (Black or White
units) (If installing a 3/4” Full Overlay)
Note: Items with an “*” in front of them can be purchased
in a kit from your dealer. Order U-Line Part No.
U-CLRDRAINKIT and this kit will contain all these items.
These items are only sold as a kit, each item is not sold
seperately.
05/2007
3
www.U-LineService.com
CLR2160/CLRCO2175 Ice Makers
Inspection
Exterior Cleaning
Unwrap and inspect the unit on a flat, level surface
capable of supporting its entire weight.
(As Required)
Black and White Models:
Removing Protective Coating
• The door, grille and cabinet may be cleaned with a mild
detergent and warm water solution. Do not use
solvent-based or abrasive cleaners. Use a soft sponge
and rinse with clean water. Wipe with a soft, clean
towel to prevent water spotting.
(Stainless Steel Units Only)
When inspecting/installing a Stainless Steel unit, the
protective coating covering the unit must be removed
first. Start at a corner of the unit/door and pull back the
protective coating to remove it from the unit/door.
Stainless Steel Models:
After all the protective coating has been removed from
the unit/door, clean all Stainless Steel surfaces with Claire
Stainless Steel Polish and Cleaner or comparable product
or a mild detergent and warm water solution and soft
cloth. Do NOT use abrasive cleaning agents.
• Stainless steel models can discolor when exposed to
chlorine gas, pool chemicals, salt water or cleaners with
bleach.
• Keep your stainless steel unit looking new by cleaning
with a good quality all-in-one stainless steel cleaner/
polish on a monthly basis. For best results use Claire
Stainless Steel Polish and Cleaner, which can be
purchased from U-Line Corporation. (The part number
is 173348.) Comparable products are acceptable.
Frequent cleaning will remove surface contamination
that could lead to rust. Some installations may require
cleaning on a weekly basis.
Note: If cleaning with mild detergent and warm water
solution and soft cloth, the unit MUST be treated with
Claire Stainless Steel Polish and Cleaner or comparable
product to prevent discoloration.
• Do not clean with steel wool pads.
• Do not use cleaners that are not specifically
intended for stainless steel (this includes glass,
tile and counter cleaners).
• If any surface discolors or rusting appears, clean it
quickly with Bon-Ami or Barkeepers Friend Cleanser
and a non-abrasive cloth. Always clean in the direction
of the grain. Always finish this process with Claire
Stainless Steel Polish and Cleaner or comparable
product to prevent further problems.
• Use of abrasive pads such as Scotchbrite will
cause the graining in the stainless to become
blurred.
• Rust that is allowed to linger can penetrate into the
surface of the stainless steel and complete removal of
the rust may not be possible.
www.U-LineService.com
4
05/2007
CLR2160/CLRCO2175 Ice Makers
Product Dimensions CLR2160
3 Prepare Site
26-1/8"
Including
Handle
24"
Including
Handle
Your U-Line product has been designed for either freestanding or built-in installation. When built-in, your unit
does not require additional air space for top, sides or rear.
However, the front grille must NOT be obstructed and
clearance is required for water, drain and electrical
connections in the rear.
34-1/8"
Note: Unit can NOT be installed behind a closed cabinet
door.
34-1/8"
Cut-Out Dimensions CLR2160
14-15/16"
14-15/16"
Black and White
Stainless Steel
Figure 2
See Electrical
Specifications
for Power Supply
Please note that the unit has adjustable feet that can add
one additional inch to height during leveling or to match
adjacent cabinets (see Figure 50 on Page 21).
24"
34-1/4"
to
35-1/8"
Door Swing/Clearances Information
CLR2160
8"
15-3/16"
Black and White units have a zero clearance for the door
to open 90° (see Figure 3). Stainless Steel models require
a minimum of 2-1/8" door clearance to accommodate the
handle if the unit is installed next to a wall or similar type
of structure.
Figure 1
Follow the cut-out drawing in Figure 1. The 15-3/16"
width allows 1/4" for ease in installation and removal of
the unit. The 24" depth is the cabinet depth in most
installations. The unit is 24" deep including the handle
on Black and White models and 24" deep including the
door and not the handle on Stainless Steel models (see
Figure 2).
Wall
Wall
1/4" Min.
2-1/8" Min.
IMPORTANT
If you would like to align the face of the unit with other
adjacent cabinet doors in certain installations, you may
need to alter the wall just behind the drain connection on
the unit to accommodate the drain. The actual amount of
alteration will be determined by your actual drain
connection components.
21-3/4"
21-3/4"
16-1/2"
90°
Door Swing
Black and White
16-1/2"
90°
Door Swing
Stainless Steel
Figure 3
05/2007
5
www.U-LineService.com
CLR2160/CLRCO2175 Ice Makers
Cut-Out Dimensions CLRCO2175
Product Dimensions CLRCO2175
24"
Including
Handle
26-1/8"
Including
Handle
34-1/8"
See Electrical
Specifications
for Power Supply
34-1/8"
24"
34-1/4"
to
35-1/8"
23-15/16"
23-15/16"
8"
Black and White
Stainless Steel
Figure 5
24-3/16"
Figure 4
Please note that the unit has adjustable feet that can add
one additional inch to height during leveling or to match
adjacent cabinets (see Figure 50 on Page 21).
Follow the cut-out drawing in Figure 4. The 24-3/16"
width allows 1/4" for ease in installation and removal of
the unit. The 24" depth is the cabinet depth in most
installations. The unit is 24" deep including the handle
on Black and White models and 24" deep including the
door and not the handle on Stainless Steel models (see
Figure 5).
Door Swing/Clearances Information
CLRCO2175
Black and White units have a zero clearance for the door
to open 90° (see Figure 6). Stainless Steel models require
a minimum of 2-1/8" door clearance to accommodate the
handle if the unit is installed next to a wall or similar type
of structure.
IMPORTANT
If you would like to align the face of the unit with other
adjacent cabinet doors in certain installations, you may
need to alter the wall just behind the drain connection on
the unit to accommodate the drain. The actual amount of
alteration will be determined by your actual drain
connection components.
Wall
Wall
1/4" Min.
2-1/8" Min.
21-3/4"
21-3/4"
25-1/2"
90°
Door Swing
Black and White
25-1/2"
90°
Door Swing
Stainless Steel
Figure 6
www.U-LineService.com
6
05/2007
CLR2160/CLRCO2175 Ice Makers
Reversing the Door
4. Remove the two door closer inserts from the existing
bottom hinge and install as shown on the new bottom
hinge (see Figure 11).
(Black and White Units Only)
All U-Line units (except
Stainless Steel models) may
be left- or right-hand
opening. The door opening is
easily reversed by moving the
hinge hardware to the
opposite side. The top hinge
hardware will be used on the
bottom of the other side and
the bottom hinge hardware
will be used on the top of the
other side (see Figure 7).
1
Door
Closer
Inserts
2
ULIN_0003_A
Figure 10
Figure 11
To reverse the door:
1. Remove top hinge screw
pin from door (Phillips
Figure 7
screwdriver) (see Figure
8). Remove door by tilting
forward and lifting off bottom hinge pin.
5. Remove existing bottom hinge (3 screws) and remount
on opposite side TOP. Remove hinge screw pin.
ULIN_0015_A
6. Remove the plastic hole plug from the top of the door
to allow the pivot pin to be inserted in the new
location. Install the plug into the vacated hole on the
opposite side.
2. Remove plastic screw plugs (3 each, top and bottom)
from new hinge location. Do not discard (see Figure 9).
7. With bottom of door facing up, remove pivot plate
(2 screws), flip over, and remount on opposite side of
door (see Figure 12). Be sure notch in plate faces
center.
Screw Plugs
Figure 9
Figure 12
Figure 8
8. Holding door upright with top of door tilted forward,
place hole of door pivot plate on bottom hinge screw
pin (see Figure 13).
ULIN_0133_A
3. Remove top hinge (3 screws), reinstall hinge screw pin,
and remount on opposite side BOTTOM (see Figure
10).
9. Tilt top of door into
position in top hinge and
install top hinge screw pin.
10. Install plastic screw plugs
removed in Step 2 in old
hinge holes (3 each, top
and bottom).
Figure 13
05/2007
7
www.U-LineService.com
CLR2160/CLRCO2175 Ice Makers
Other Site Requirements
Side-By-Side Installation
Instructions CLR2160
Power Supply
For a complete refreshment center, install your CLR2160
Clear Ice Maker beside a U-Line Refrigerator, Combo, or
Wine Captain Model (see Figure 14 for typical cut-out).
Note that each Side-By-Side Installation will be different.
The unit requires a grounded and polarized 115 VAC,
60 Hz, 15A circuit (normal household current). See
Electrical Specifications on Page 20.
Water Supply
• Cut-out width for a side-by-side installation is the total
of the widths listed under Cut-Out Dimensions in each
unit’s Installation Guide.
The unit requires a 1/4” O.D. soft copper water supply
line. For more information see Page 15.
For example:
Drain
Placing a CLR2160 Clear Ice Maker next to a 2115 series
unit would require a cut-out width of:
15-3/16" + 15-3/16" = 30-3/8".
The unit’s generous 7-inch drain connection height
extends the distance the unit can be located from a
gravity drain. For more information see Page 15.
Placing a CLR2160 Clear Ice Maker next to a 2175 series
unit would require a cut-out width of:
15-3/16" + 24-3/16" = 39-3/8".
IMPORTANT
Drain can NOT be located directly below unit. Unit has a
solid base that will not allow unit to drain below itself.
Environmental Requirements
• No trim kit is required. However, 1/4-inch space needs to
be maintained between the units to ensure
unobstructed door swing.
Many U-Line models are designed to operate in harsh
outdoor environments. Special considerations include the
following:
• Units must operate from separate, properly grounded
electrical receptacles placed according to each unit’s
Electrical Specifications.
• The units are designed to operate between 50°F (10°C)
and 110°F (40°C). High ambient temperatures (110°F
[40°C] or higher) may reduce the unit’s ability to reach
low temperatures and may also reduce the ice
production rate for those models with ice makers.
Typical Side-By-Side Cut-Out
• If the ambient temperature is expected to drop below
45°F (7°C), drain all water from the unit to prevent
freezing damage not covered by the warranty.
• For best performance, keep the unit out of direct
sunlight and away from heat generating equipment.
34-1/4"
to
35-1/8"
• For best performance and life outdoors, place under a
counter or provide shelter of some kind.
24"
7"
• In climates where high humidity and dew points are
present, condensation may appear on outside surfaces.
This is considered normal. The condensation will
disappear when the humidity drops.
www.U-LineService.com
Preferred
Location
for CLR2160
Receptacle
Acceptable
Location
1/4" Space
Between Appliances
1"
Figure 14
8
05/2007
CLR2160/CLRCO2175 Ice Makers
Side-By-Side Installation
Instructions CLRCO2175
4 Prepare and Install Door Panel
(Black and White Units Only)
For a complete refreshment center, install your
CLRCO2175 Clear Ice Maker/Refrigerator beside a U-Line
Drawer or Wine Captain Model (see Figure 15 for typical
cut-out). Note that each Side-By-Side Installation will be
different.
Two types of custom door panels can be installed on your
Black or White unit to harmonize with or accent the
surrounding décor: a Custom 1/4" Insert or a Full Overlay.
If no custom door panel is used, go on to 5 Adjust Door.
• Cut-out width for a side-by-side installation is the total
of the widths listed under Cut-Out Dimensions in each
unit’s Installation Guide.
Custom 1/4'' Door Panel Insert
Door Panel Preparation
For example:
A custom door panel can be inserted into the doorframe.
Custom door panels can be flat or raised, as long as the
maximum panel thickness where inserted into the door
reveal (channel) is 1/4"-thick. For raised panels, the depth
of the reveal is 1/4" on all four sides.
Placing a CLRCO2175 Clear Ice Maker/Refrigerator next
to a 2115 series unit would require a cut-out width of:
24-3/16" + 15-3/16" = 39-3/8".
Placing a CLRCO2175 Clear Ice Maker/Refrigerator next
to a 2175 series unit would require a cut-out width of:
24-3/16" + 24-3/16" = 48-3/8".
IMPORTANT
Raised panels will reduce the door’s 90° swing/zero
clearance if the unit is installed next to a wall or similar
type of structure.
• No trim kit is required. However, 1/4-inch space needs to
be maintained between the units to ensure
unobstructed door swing.
For 2175 models cut the panel insert to the following
dimensions.
• Units must operate from separate, properly grounded
electrical receptacles placed according to each unit’s
Electrical Specifications.
Custom 1/4" Dimensions:
Width:
Height:
Typical Side-By-Side Cut-Out
23-1/32"
27-11/16"
For 2115 & CLR2160 models cut the panel insert to the
following dimensions.
Custom 1/4" Dimensions:
34-1/4"
to
35-1/8"
Acceptable
Location
24"
Preferred
Location for
CLRCO2175
Receptacle
Width:
Height:
The door panel must not weigh more than 20 lbs.
7"
1/4" Space
Between
Appliances
14-1/32"
27-11/16"
Door Panel Installation
1-1/2"
Install the insert as follows:
Figure 15
CAUTION
Use care when handling the insert. Insert edges may be
sharp.
1. Remove top hinge screw pin (using a Phillips
screwdriver, see Figure 16). Remove door by tilting
forward and lifting off bottom hinge pin.
05/2007
9
www.U-LineService.com
CLR2160/CLRCO2175 Ice Makers
Full Overlay Door Panel
Door Panel Preparation
A full overlay door panel completely covers the
doorframe and handle to give a built-in appearance. See
your U-Line dealer for the optional Full Overlay Door
Panel Kit.
2175 Models:
P/N U-OL2175B -- Black
P/N U-OL2175W -- White
ULIN_0133a_A
Figure 16
2115 & CLR2160 Models:
P/N U-OL2115B -- Black
P/N U-OL2115W --White
Figure 17
Appropriate hardware, Modified Handle, Replacement
Hinges and a copy of these instructions will be included in
the kit.
2. Pull door gasket out of groove (top edge of door only).
Start in the middle and pull outward, moving toward
the edge (see Figure 17). This may take some force.
1. Cut the overlay to the following dimensions (see
Figure 19).
3. Remove two outside screws holding door handle.
Slightly separate door handle from door (see
Figure 18).
Full Overlay Dimensions:
2175 Models:
Width: 23-3/4"
Height: 29-3/4"
4. Pull handle up and off.
5. Remove and discard
existing panel and
cardboard spacer.
2115 & CLR2160 Models:
Width: 14-3/4"
Height: 29-3/4"
The door panel must not weigh more than 20 lbs.
6. Slide custom door panel
insert into 1/4-inch
channel in door front.
3/4"
31/32"
7. Holding door gasket out
of the way, replace handle Figure 18
on door, making sure it is
seated properly on insert
and that screw holes line up.
1/8"
Relief Notch
for Pivot Plate
8. Install two small screws removed in Step 3.
9. Starting at the corners and working inward, push door
gasket into place on door.
10. Place door on bottom hinge pin and install upper hinge
screw.
Rear View
of
Wood Panel
Height
Width
Figure 19
ULIN_0400_A
IMPORTANT
Rear View of wood panel for right-hand hinge shown. Use
mirror image for left-hand hinges.
www.U-LineService.com
10
05/2007
CLR2160/CLRCO2175 Ice Makers
Installation Instructions
2. Create a relief (Figure 19) for pivot plate by cutting
notch in top corner of overlay panel. Refer to Figure
20 for exact specifications.
Removing Existing Door
1. Remove the door shelves by first pulling shelves up at
a 45° angle, then straight out.
15/32"
2. Remove top hinge screw pin (Phillips screwdriver).
Remove the door by tilting forward and lifting off the
bottom hinge pin.
ø 0.177" (#16 Drill)
11/16" Deep
TOP VIEW
3/8"
3. Pull door gasket out of the groove (top edge of door
only). Start in the middle and pull outward, moving
toward the edge (see Figure 21). This may take some
force.
31/32"
.125"
11/16"
Ref
BACK VIEW
1/4" Ref
Old Handle
New Handle
3/4" Min Ref
3/8"
BOTTOM VIEW
SIDE VIEW
13/32"
Figure 20
ø 5/16" x 1/4" Deep
Chamfer 1/32" x 45°
Figure 21
ULIN_0401_A
Figure 22
ULIN_0403_A
4. Remove the two screws located on both sides of the
handle.
Route notch in top corner of overlay panel as shown
(see Top and Side Views). Top of notch is entire depth
of panel, front to back.
5. Remove the handle and discard. (This handle will be
replaced with the Overlay Handle included in the Full
Overlay Door Panel Kit. See Figure 22.)
Width: 31/32"
Depth: 1/8"
6. Slide the existing door panel out of the doorframe.
CAUTION
Attaching the Full Overlay Panel
Be careful not to drill too deep! Drilling holes too deep
may destroy your door panel.
1. Place and tape the existing door panel on the back of
the overlay panel (see Figure 23) and drill holes
through both panels according to Figure 24. Remove
tape adjoining the panels and enlarge the six holes in
the steel (black/white vinyl color) panel using a 0.201"
(#7) drill.
3. Drill hole for upper door hinge (top of panel) (see
Figure 20, Top View).
0.177" diameter
(#16 drill) x 11/16" deep
2. If a user-supplied cabinet handle will be used, attach its
hardware to the overlay panel at this time.
4. Drill hole for lower door hinge (see Figure 20, Bottom
View).
5/16" diameter x 1/4" deep
CAUTION
It is important to ensure that all drilled holes are drilled to
the correct depth in order to avoid splits in the wood
when hardware is installed.
05/2007
11
www.U-LineService.com
CLR2160/CLRCO2175 Ice Makers
Removed
Door Panel
Back of
Wood
Panel
Typical
Wood Panel
Door Panel
Tape
1-3/4" Top
Side of
Wood Panel
#10 x 5/8"
Round Head Screw
Seven Required
Top of
Wood Panel
3/8"
Both Sides
Figure 23
Plastic Spacer
Seven Required
Figure 25
4. Remove the existing bottom pivot plate and replace
with the Full Overlay pivot plate (see Figure 26).
2-5/8" ± 1/4"
Existing
Door
Drill ø 5/32" x 3/8" Deep
7 Places Model 2175
6 places Model 2115 and CLR2160
15-9/16" ± 1/4"
Wood Panel Bottom Pivot Plate
(5/8" Longer Than
Existing Bottom Pivot Plate,
Flush Side Facing Out)
Existing Bottom Pivot Plate
(Remove and Discard)
#8-32 x 3/8" SEMS Hex Screw
Two Places
For use with #10 x 5/8"
Wood Screw and Nylon Spacer
Figure 26
28-7/8" ± 1/4"
IMPORTANT
Door panel and overlay panel must be aligned properly or
the door will not operate correctly.
Assembling the Door
1"
11-7/8±1/32
For use on
Model 2175 Only
1. Install the assembled panel by sliding the original door
panel back into the doorframe.
1"
2. Replace the Overlay Handle and secure with the two
screws removed in Step 4 under Removing Existing
Door.
ULIN_0402_A
Figure 24
3. Attach Overlay cap to door, opposite side of where
hinges will be (see Figure 27).
3. Attach the door panel to the overlay panel using #10 x
5/8" wood screws and nylon spacers. The nylon spacers
fit between the overlay panel and the door panel as
shown in Figure 25. The spacers allow the original
door panel to slide back into the 1/4"-thick door
reveal (channel).
Overlay Cap
3/4" Wood Panel
Replacement Handle
Figure 27
www.U-LineService.com
12
05/2007
CLR2160/CLRCO2175 Ice Makers
4. Attach Top Pivot Plate to door handle, on side where
hinges will be. Use the two #8-32 x 1/2" Flat Head
Phillips screws (Black) supplied with kit (see Figure 28).
#8-32 x 1/2" Flat Head Screws
Black, Two Places
3/4" Wood Overlay
Existing Door
Door Closure Top
Boss
Top Pivot Plate
Screw to attach Handle
Removed in step 4
Door Closure
Bottom
Boss
Pivot Post
Figure 28
#8-32 x 1/2" Flat Head Screw
Three Places
Wood Panel Bottom Hinge Plate
(5/8" Longer than Existing Bottom Hinge Plate)
Figure 30
5. Starting at the corners and working toward the center,
push the door gasket back into place.
IMPORTANT
Installing the Door
Pivot posts must be cleaned. Closers must also be clean
and greased to ensure proper operation.
1. Remove the existing hinges from the unit, saving the
door closure assembly.
5. Place the modified door onto the pivot post.
2. Install the new Replacement Top Hinge onto the unit
(see Figure 29).
6. Position door and install the pivot post into the top
hinge (using the Phillips screwdriver).
7. Adjust door as needed for proper closure.
Wood Panel Top Hinge Plate
(5/8" Longer than Existing Top Hinge Plate)
8. Check to see that light goes off when the door closes.
Pivot Post
9. Reinstall the door shelves by lining up the bosses and
first pushing straight in, then down at a 45° angle.
#8-32 x 1/2"
Flat Head Screw
Three Places
Top Pivot Plate
Figure 29
Door Panel
ULIN_0405
3. Install the pivot post into the new Replacement Bottom
Hinge (using the Phillips screwdriver) and install the
hinge onto the unit.
4. Replace the door closure assembly onto the bottom
pivot post (see Figure 30). Be sure that bosses on
closers align with holes in hinge and hinge plate.
05/2007
13
www.U-LineService.com
CLR2160/CLRCO2175 Ice Makers
5 Adjust Door
Checking Door Alignment
The unit’s door is aligned at the factory before shipment.
However, its alignment could have been disturbed during
shipment or during door panel installation.
Slotted
Mounting
Holes
Notch
IMPORTANT
Properly aligned, the door should be 1/8" below the top of
the unit’s cabinet, NOT flush with the top (see Figure 31).
Raise
Outside
Door Edge
Lower
Outside
Door Edge
Figure 33
1/8"
3. See Figure 33. If the top far edge of the door needs to
move UP, move the hinge plate toward the outside of
the door and retighten screws. If the top far edge of the
door needs to move DOWN, move the hinge plate
toward the inside of the door and retighten screws.
Figure 31
4. Mount the door to recheck alignment and repeat Steps
2 and 3 if further adjustment is necessary.
1. Compare the top edge of the door to the top edge of
the cabinet.
5. When top edge of door is parallel to top edge of
cabinet, remove the door and ensure the two screws
are secure.
2. If the door edge is 1/8" below and parallel to the top of
the cabinet, go on to 6 Prepare Plumbing. If it is not,
note whether the side opposite the hinge needs to be
moved UP or DOWN, and use the following procedure.
6. Remove the door closers from the bottom hinge, clean
thoroughly and lubricate the mating surfaces with
petroleum jelly.
Note: If door is adjusted correctly, but panel is not square
with the adjacent cabinets, slight adjustments can be
made by drilling the holes in the vinyl coated steel panel
slightly oversized. See Figure 25 on Page 12.
7. Reinstall the closers, lining
up the bosses with holes in
hinge and hinge plate (see
Figure 34).
Adjusting Door Alignment
8. Mount the door, install top
hinge pivot pin and go on
to 6 Prepare Plumbing.
1. Remove top hinge screw
pin (Phillips screwdriver,
see Figure 32). Remove
door by tilting forward
and lifting off bottom
hinge pin.
Boss
Figure 34
2. With door upside-down,
loosen but do not remove
the two screws on the
door’s bottom hinge plate.
Figure 32
www.U-LineService.com
Door
Closer
Inserts
ULIN_0133_A
14
05/2007
CLR2160/CLRCO2175 Ice Makers
2. Locate the U-Line supplied garden hose fitting. Ensure
the end of the copper tubing has been cut straight and
free of burrs. Slide the compression nut and ferrule
onto the copper tubing as shown (see Figure 36). Push
the assembly completely into the the garden hose
fitting and tighten using the two wrenches. Wait to
connect this assembly to the appliance until the drain
connection is ready.
6 Prepare Plumbing
CAUTION
Plumbing installation must observe all state and local
codes. All water and drain connections MUST BE made by
a licensed/qualified plumbing contractor. Failure to follow
recommendations and instructions may result in damage
and/or harm.
9/16" Wrench
Water Supply Connection
When connecting the water supply, follow these
guidelines:
1/4" Copper Water
Supply Line
• Review the local plumbing codes before you install the
unit.
• Connect to the cold water supply.
7/16" Wrench
• The water pressure should be between 20 and 120 psi.
• The water line MUST have a shut-off valve in the 1/4”
O.D. supply line.
• Leave approximately 8’ of water line to be coiled
behind the appliance (see Figure 35). The water line
should be looped into 2 coils. This will allow the unit to
be removed for cleaning and servicing. However, make
certain that the tubing is not pinched or damaged
during installation.
From Water Supply
to Ice Maker
Figure 36
ULIN_S_0168_A
Drain Connection
IMPORTANT
Note: U-Line requires the use of copper tubing for
installation. Do not use any plastic water supply line because
the line is under pressure at all times. Plastic may crack or
rupture with age and cause water damage to your home.
Drain can NOT be located directly below unit. Unit has a
solid base that will not allow unit to drain below itself.
The CLR2160 or CLRCO2175 can be installed using a
Gravity Drain, a Factory-Installed Drain Pump (U-Line P60)
or a Locally-Installed (U-Line P60) Drain Pump. Drain lines
must have a 5/8” inside diameter. The floor drain must be
large enough to accommodate drainage from all attached
drains.
To connect to water supply:
1. Locate the desired cold water supply location. Attach a
1/4” copper line to this location and route the tubing
to the appliance. Leave approximately 8’ of water line
to be coiled behind the appliance. The water line
should be looped into 2 coils. This will allow the line to
flex when removing the unit for cleaning and servicing
(see Figure 35).
Note: We strongly recommend the use of the U-Line
CLRDRAINKIT for both gravity & pump installations. A
complete drain kit containing all the items needed to
connect your unit are available from your dealer. Order
Part No. U-CLRDRAINKIT.
Note: Longer drain connections may require additional
drain hose lengths. Additional drain line can be purchased
from your dealer or directly from McMaster-Carr.
(McMaster-Carr # 52375K35)
Follow these guidelines when installing drain lines to
prevent water from flowing back into the ice maker
storage bin and/or potentially flowing onto the floor,
causing water damage:
Gravity Drain
A Gravity Drain may be used if:
Figure 35
05/2007
• Drain line has at least a 1-inch drop per 48 inches of
run (1/4 inch per foot).
ULIN_S_165
15
www.U-LineService.com
CLR2160/CLRCO2175 Ice Makers
Gravity Drain
Normal
Proper Drain
With Trap
Poor Drainage, Water Will Back Up
Waste
Shut-Off
Valve
Hot
Water
Cold
Water
With Trap and Vent
Proper Drain
ULIN_0569_A
Figure 37
Figure 38
Waste
ULIN_0570_A
• Drain line does not create traps or created traps are
vented (see Figure 37).
Drain Fitting from
Back of Unit
See Figure 38 for a typical Gravity Drain installation.
If using a Gravity Drain:
5/8" x 5/8"
Barb Connector
1. Slide 2 hose clamps onto the drain connection on the
rear of the appliance.
Worm Clamps
2. Insert the barbed fitting halfway into this connection.
3. On the other end of this barbed fitting attach the 5/8”
braided tubing.
Drain Line
4. Slide a clamp on each side of the barbed fitting as
shown (see Figure 39).
5. Insulate the drain line, if necessary to prevent
condensation. Go on to Final Water/Drain Connection
Page 18.
Figure 39
ULIN_S_0166b2_A
Factory-Installed Drain Pump
If your drain line will run up to a stand pipe, disposal
assembly or spigot assembly or does not otherwise meet
the requirements for a Gravity Drain, you may have
ordered the CLR2160 or CLRCO2175 with a U-Line P60
Drain Pump. See Figures 42, 43 and 44 for typical
installations requiring a Drain Pump. If you need to install
a P60 Drain Pump into your unit, see Locally-Installed
Drain Pump on Page 17.
IMPORTANT
Before installing your U-Line CLR2160 or CLRCO2175 with
Factory-Installed U-Line P60 Pump, it is extremely
important to check and test all hose connections at the
drain pump. There is a possibility that hose connections
may have loosened during shipment.
To check and test hose connections:
1. Make certain the unit is not plugged into an electrical
outlet.
www.U-LineService.com
16
05/2007
CLR2160/CLRCO2175 Ice Makers
2. Carefully push the power cord grommet through the
hole in the back panel (see Figure 40, CLRCO2175
shown).
5. Place a suitable container beneath the pump’s discharge
tube. (The bucket must be able to hold a minimum of
one gallon.)
6. Plug the ice maker power cord into a properly
grounded, polarized electrical outlet.
Screws
Back
Panel
7. Place the unit into OFF mode by holding power key for
10 seconds. Not doing this will cause the unit to start
the fill cycle which will run for 3 minutes.
8. Verify pump operation by pouring one gallon of water
into the ice storage bin of the ice maker. The pump
should energize and pump the water into the container.
9. At this time, verify that all tube and clamp connections
are tight and leak-free.
10. Unplug unit power cord from electrical outlet.
11. Reinstall back panel.
Grommet
Drain
Fitting
Power
Cord
Water
Connection
Locally-Installed Drain Pump
ULIN_0574_A
Figure 40
If a gravity drain connection is not possible, and you have
not purchased a CLR2160 or CLRCO2175 with factoryinstalled pump, we strongly recommend the use of the
U-Line P60 drain pump. The U-Line P60 drain pump is
available through your Dealer, with complete installation
instructions. If a pump other than the U-Line P60 drain
pump is to be used, it must meet the following
specifications:
3. Remove 12 screws and back panel.
WARNING
Back panel serves as a guard. DO NOT put your
hands inside the ice maker cabinet or attempt to
touch any components except the discharge tube
during testing. Failure to follow this warning
could result in serious personal injury or death.
• It must be UL listed and have a UL listed, 120 VAC,
3-wire grounded power cord.
• It must have overall maximum outside dimensions of
8-3/4" wide x 5-3/4" deep x 7-3/4" high.
4. Check that the clamps and hose connections are tight at
the following areas (see Figure 41):
• It must have a minimum flow rate of 1.5 gallons per
minute at 10 feet of lift.
• Discharge tube (A)
• It must have a sealed sump which does not allow water
leakage in the case of a power outage, restricted drain
or pump failure.
• Drain tube (B)
• Vent tube (C)
B
• It must have a check valve in the discharge line to
prevent waste water return to the pump.
B
C
C
• It must have an overflow protection control which will
shut off power to the ice maker in the event of a pump
failure.
A
• It must have an operating temperature range of 50°F
to 110°F (10°C to 40°C).
IMPORTANT
Back View
Figure 41
05/2007
Side View
In the event of a power outage, restricted drain or pump
failure, the failure to use the U-Line P60 drain pump or a
pump with the above listed specifications, could result in
substantial water leakage and pooling with severe and
costly water damage and related consequential damages
and harm.
ULIN_0575_A
17
www.U-LineService.com
CLR2160/CLRCO2175 Ice Makers
Stand Pipe
P60 Pump Required
9/16" Wrench
1/4" Copper Water
Supply Line
Waste
Shut-Off
Valve
7/16" Wrench
Hot
Water
Waste
Figure 42
Cold
Water
Figure 45
ULIN_0571a_A
From Water Supply
to Ice Maker
ULIN_S_0168_A
To connect to drain:
Disposal Assembly
P60 Pump Required
1. Slide 2 hose clamps onto the drain connection on the
rear of the appliance.
Air Gap
(Optional Hook-Up)
2. Insert the barbed fitting halfway into this connection.
3. On the other end of this barbed fitting attach the 5/8”
braided tubing.
4. Slide a clamp on each side of the barbed fitting as
shown (see Figure 45).
Waste
Hot
Water
5. Insulate the drain line, if necessary to prevent
condensation. Go on to Final Water/Drain Connection.
Page 18.
Cold
Water
Shut-Off
Valve
Figure 43
Final Water/Drain Connection:
1. Connect the water supply fitting by screwing the brass
garden hose fitting to the watervalve in the rear of
the unit.
ULIN_0572a_A
Y-Branch Tailpiece
P60 Pump Required
2. Tighten this fitting with pliers.
Air Gap
(Optional Hook-Up)
Note: Do not use Teflon tape or joint compound on this
fitting. The rubber washer provides an adequate seal.
Other materials could cause blockage of the valve.
Waste
Shut-Off
Valve
Hot
Water
Figure 44
Cold
Water
ULIN_0573a_A
WARNING
To prevent accidental electrocution, make certain
that the floor surfaces surrounding the unit are
dry whenever power is removed from, or applied
to, the unit.
www.U-LineService.com
Figure 46
18
ULIN_S_0166b1_A
05/2007
CLR2160/CLRCO2175 Ice Makers
3. Attach the copper water line to the back of the unit
using the supplied clamp and the back panel screw (see
Figure 46, CLR2175 model shown). This will prevent
rotation of the line when moving the unit.
13. If any issues are found, retrace the drain connection,
correct the issue and retest with water.
14. Go on to 7 Prepare Power Supply.
4. Plug in the unit and put unit into OFF mode by holding
the power key for 10 seconds. Not doing this will cause
the unit to fill with water for 3 minutes.
5. Turn on the water supply and ensure the connections
are free of leaks.
6. Begin to push the appliance into the desired cabinet
opening. The copper tubing should remain in 2 coils
behind the unit.
IMPORTANT
Normal operation creates some vibration. A water supply
line contacting cabinet wall may cause excessive noise
during operation or damage to the line.
7. While pushing the unit into the opening, continuously
reroute the drain tube to avoid kinks. The most
common installation pulls the slack into an adjacent
cabinet or basement area.
8. If installing a gravity drain, ensure you provide proper
slope.
9. After unit is in its final position, finish routing drain
tube to the desired location. Common installations use
a floor drain, standpipe, garbage disposal, or Y-branch
tailpiece type drain connection (see Figures 42, 43 and
44).
10. Check to ensure unit is level both side to side and front
to back. See Leveling Information on Page 20.
IMPORTANT
For the gravity/floor drain or the standpipe be sure to
secure the drain line to these items to prevent it from
coming loose and causing water damage.
IMPORTANT
For disposer or Y-branch tailpiece connections press the
drain tube over the barbed end of the connector and
secure with a worm clamp. Make sure the knockout inside
the tailpiece has been removed for both types of
connections. Depending on the size of the Y-branch or
disposer fitting, an adapter may be necessary to interface
between the 5/8” hose and connection.
11. Turn the unit to the on position by holding the power
key for 10 seconds.
12. Pour 1 gallon of water into the ice bin and check all
connections for leaks. Ensure the water is flowing from
the bin. If the water does not flow from the bin there
may be an issue with the drain connection, such as kinks
or improper slope. If your unit has a drain pump, an
indicator of P1 on the display will alert you of a slow or
clogged drain.
05/2007
19
www.U-LineService.com
CLR2160/CLRCO2175 Ice Makers
7 Prepare Power Supply
8 Level the Unit
Electrical Specifications
Leveling Information
CAUTION
IMPORTANT
It is extremely important that the unit is level. If it is not
level, the ice mold will not fill evenly.
Electrical installation must observe all state and local
codes. This unit requires connection to a grounded (threeprong), polarized receptacle that has been placed by a
qualified electrician.
A unit that is not level can
cause a reduction in ice rate,
uneven sized cubes or water
spilling into the storage
area, which will cause the ice
in the bin to melt
prematurely (see Figure 48).
The unit requires a grounded and polarized 115 VAC,
60 Hz, 15A power supply (normal household current).
An individual, properly grounded branch circuit or circuit
breaker is recommended. A GFCI (ground fault circuit
interrupter) is usually not required for fixed location
appliances and is not recommended for your unit because
a GFCI could be prone to nuisance tripping. However, be
sure to consult your local codes.
Remember that floors near
drains have a tendency to
slope toward the drain.
See Figure 47 for recommended receptacle location.
Plugging the unit into a receptacle located behind an
adjacent cabinet will allow the CLR2160 or CLRCO2175 to
be more easily serviced with self-diagnostics without
disturbing your installation.
Figure 48
1. Use a level to check the
levelness of the ice maker
from front to back and
from side to side. Level
should be placed along
top edge and side edge
as shown (see Figure 49).
1
Figure 49
Acceptable
Location
24"
ULIN_0193_A
Preferred
Location
for Receptacle
7"
1-1/2"
Figure 47
WARNING
SHOCK HAZARD — Electrical Grounding Required.
• Never remove the round grounding prong from
the plug and never use a two-prong grounding
adapter.
• Never use an extension cord to connect power to
the unit.
Go on to 8 Level the Unit.
www.U-LineService.com
20
05/2007
CLR2160/CLRCO2175 Ice Makers
2. If the ice maker is not level, adjust the feet on the
corners of the unit as necessary (see Figure 50).
9 Install the Unit
Installation of the CLR2160
1. Open the water supply valve in the main water source.
2. Plug in the power cord.
3. Open the door and press the POWER icon (see Figure
53, 1) (Page 23) on the display panel until OFF is
displayed.
Turn Foot to Adjust
Note: If the unit is NOT turned OFF, water will
immediately start flowing into the unit when it is first
plugged into the electrical outlet.
Figure 50
4. Gently push the unit into position. Be careful not to
kink the drain or water supply line or entangle the
electrical cord.
3. Check the levelness after each adjustment and repeat
the previous steps until the unit is level. Go on to
9 Install the Unit.
5. Re-check the leveling, from front to back and side to
side. Make any necessary adjustments. The unit’s top
surface should be approximately 1/8" below the
countertop.
Installation Tip
If the room floor is higher than the floor in the cut-out
opening, adjust the rear feet to achieve a total unit rear
height of 1/8" less than the opening’s rear height. Shorten
the unit height in the front by adjusting the front feet.
This allows the unit to be gently tipped into the opening.
Readjust the front feet to level the unit after it is correctly
positioned in the opening.
Test the drain system by pouring one gallon of water into
the ice bin. The water should drain freely and there should
be no leakage.
Installation of the CLRCO2175
1. Open the water supply valve in the main water source.
2. Plug in the power cord.
3. Open the door and press the POWER icon (see Figure
53, 1) (Page 23) on the display until OFF is displayed.
Note: If the unit is NOT turned OFF, water will
immediately start flowing into the unit when it is first
plugged into the electrical outlet.
4. Gently push the unit into position. Be careful not to
kink the drain or water supply line or entangle the
electrical cord.
5. Re-check the leveling, from front to back and side to
side. Make any necessary adjustments. The unit’s top
surface should be approximately 1/8" below the
countertop.
6. Test the drain system by pouring one gallon of water
into the ice bin. The water should drain freely and there
should be no leakage.
7. Remove the tape from the glass shelves and wipe out
the inside of the unit with a clean, water-dampened
cloth.
05/2007
21
www.U-LineService.com
CLR2160/CLRCO2175 Ice Makers
Relocating the Shelves (CLRCO2175)
Installation Troubleshooting
Both the glass shelves in the refrigerator and the inner
door shelves can be moved to accommodate your bottles,
cans and containers.
Q: Problem
Water is leaking under the unit.
Glass Shelves on Right-Hand Hinge Units
A: Solution
1. Open door fully, grasp shelf firmly, lift front edge
slightly and pull straight out.
A water leak under the unit is most likely caused by a bad
connection in the water supply line. Make sure the water
line’s brass fitting is screwed tight to its valve and
threaded correctly. Make sure the fill tube’s connection to
the water line is also tight. Check drain line to make sure
it has not been disconnected from drain connection on
back of the unit or disconnected from the drain.
2. Choose new location and slide shelf onto the
appropriate rib.
Glass Shelves on Left-Hand Hinge Units
1. See Figure 51. Pull shelf
out about 6” to clear the
wall’s molded protrusion.
2. Tilt right-hand edge of
shelf up.
Q: Problem
The door remains open unless it is pushed closed.
1. Pull Out 6"
3. Pull
3. Keeping at this angle and
hugging the right wall,
pull the shelf out.
4. Choose new location and
insert over ribs, tilting
right-hand edge up. Push
in, then lower shelf onto
ribs.
A: Solution
2. Tilt
The hinges should be self-closing when the door is open
approximately 8". If this is not the case, make sure the
closers (at the bottom of the hinge pin) are clean, greased
and installed correctly. Also, re-check leveling from front
to back of the unit and readjust if necessary. Make sure
that pivot plate is installed correctly.
Figure 51
Q: Problem
Door Shelves
The custom overlay door was designed to align with the
rest of the cabinet doors, but the unit has crept forward.
1. First pull shelf up at a 45°
angle, then straight out
(see Figure 52).
A: Solution
Notch
First, make sure that the electrical cord and water supply
line are not obstructing the installation. If they are not,
there is mostly likely not enough room allowed for the
drain connection on the rear of the unit. You may need to
alter the wall behind the unit to accommodate the drain
connection.
2. Choose new location and
line up on bosses. First
push straight in, then
down at a 45° angle.
Boss
Figure 52
www.U-LineService.com
22
05/2007
CLR2160/CLRCO2175 Ice Makers
IMPORTANT
10 Start-Up for the First Time
It is possible that dirt or scale will dislodge in the water
line. Always throw away all ice cubes made during the
first two to three hours of operation.
Initial Start-Up
Once installation and leveling is complete, the unit is
ready for initial start-up and operation. The display panel
is located inside the unit, on the top of the refrigerator
side (see Figure 53, 1).
Other Settings
Other settings for the unit are factory preset. No
adjustments should be necessary at this time. For
information about Ice Cube Thickness, or additional
settings, see the Use and Care Guide.
The LED display shows the temperature set point
and is calibrated in degrees Fahrenheit. The
controller is factory programmed for a set point of
38°F which will show when the unit is first powered
up.
1
Figure 53
2
3
4
5
ULIN_0058_A
1. Open the door and remove the cover in front of the
evaporator by gently compressing and pulling
forward. This will enable you to observe the water
flow over the evaporator.
2. Check that the overflow tube is inserted securely into
the water trough.
3. Press the POWER icon (see Figure 53, 1) and hold for
approximately five seconds until the °F symbol flashes
and release. The water fill valve will energize and fill
the water reservoir. The water fill valve shuts off after
approximately 180 seconds (3 minutes). The compressor
begins to operate.
The CLRCO2175 display (see Figure 53, 3) will show
the set-point temperature (38°F) when the unit is on
and will show OFF when the unit is off. The CLR2160
display (see Figure 53, 3) will show ICE when the unit
is on and will show OFF when the unit is off.
4. Watch the water flow over the evaporator assembly (ice
cube tray) to familiarize yourself with the operation.
Upon initial start-up, water flow over the evaporator
may be uneven. This may cause uneven sized cubes or
water spilling into the ice storage bin. This is a normal
situation and will correct itself within the first 24 hours
of operation.
5. Replace the evaporator cover. Note that after the first
slab of ice is produced, ice production will stop until the
refrigerator side of the CLRCO2175 reaches the set
point temperature. Then, ice production will begin
again.
6. Allow unit to run for at least 24 hours to stabilize
before making any temperature or ice adjustments.
05/2007
23
www.U-LineService.com
Start-Up Troubleshooting
Who to Call
Q: Problem
Service Information
Unit does not appear to turn on when POWER icon is
pressed.
If the need for service arises, call the U-Line Customer
Care Center directly @ 800-779-2547. To ensure accurate
assistance, please have your Model Number and Serial
Number and an explanation of the problem. The Model
and Serial Number plate is located inside unit at upper
right hand corner.
A: Solution
Remember that the compressor will not operate until the
water has been filling for about 3 minutes. Make sure unit
is plugged in and outlet has power (circuit breaker has
not tripped). If the unit is equipped with a drain pump,
check that the drain line is not obstructed. Unit will shut
down due to the safety design of the pump if water
cannot drain.
If you need to locate a service company, you can go online
at www.U-LineService.com and search for a service
company by zip code.
Q: Problem
Water does not appear to be flowing into unit.
A: Solution
Check that the water is connected and turned on, the line
is not obstructed and the overflow tube is inserted
securely into water trough.
Q: Problem
The unit has been operating for 24 hours and water is still
not flowing evenly over evaporator.
A: Solution
Level unit for even water flow. Uneven water flow will
reduce ice rate and cause water to spill in ice bin.
IMPORTANT
See the Use and Care Guide’s Troubleshooting Guide for
more solutions.
For more than four decades, U-Line has distinguished itself as the leader in built-in
undercounter ice making, refrigeration and wine storage appliances.
U-Line Corporation, located in Milwaukee, WI, is a family operated manufacturer of built-in
undercounter icemakers, Combo® icemaker/refrigerators, Wine Captain® wine storage units,
refrigerators, refrigerated drawers and refrigerator/freezers.
©2007 U-Line Corporation
Publication No. 30141E
05/2007 Rev. D
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising