American Standard | 4114.001.075 | Installation Instructions LAKELAND 4114.001
Add to my manuals4 Pages
American Standard 4114.001.075 is a single control kitchen faucet with a cast spout, designed for durability and ease of use. It features a stylish stainless steel finish that will complement any kitchen décor. The faucet has a high-arc spout that provides ample clearance for filling pots and pans, and a pull-out spray head for added convenience. The spray head can be used for rinsing dishes, cleaning vegetables, or filling large containers. The faucet also includes a ceramic disc cartridge for smooth, drip-free operation.
advertisement
LAKELAND
®
SINGLE CONTROL KITCHEN
FAUCET WITH CAST SPOUT
Installation
Instructions
4114.001
4114.001F15
Thank you for selecting American-Standard...
the benchmark of fine quality for over 100 years.
To ensure that your installation proceeds smoothly-please read these instructions carefully before you begin.
Recommended tools
Certified to comply with ANSI A112.18.1M
M 9 6 8 4 6 9 R E V. 1. 6
Regular Screwdriver
Phillips Screwdriver
Adjustable Wrench
Plumbers' Putty or Caulking
1
INSTALL FAUCET WITH OR WITHOUT DECK ESCUTCHEON
CAUTION
Turn off hot and cold water supplies before beginning.
(A) Installation with ESCUTCHEON (1). Apply a bead of putty to bottom edge of ESCUTCHEON with PUTTY PLATE (1).
Insert supply HOSES (2) and SHANK (3) through hole of ESCUTCHEON with PUTTY PLATE (1) and mounting surface.
Follow mounting instructions below to secure faucet to mounting surface.
(B) Installation less ESCUTCHEON (1). Discard ESCUTCHEON with PUTTY PLATE (1). Insert supply HOSES (2) and
SHANK (3) through mounting hole and seat SPOUT BASE onto sink or mounting surface. Do not use putty.
Assemble RUBBER WASHER (4), BRASS WASHER (5), and threaded LOCKNUT (6) onto SHANK (3) from underside of sink or mounting surface. Hand tighten LOCKNUT (6) and check that rotation of HANDLE (7) from HOT to COLD is centered.
Use a screwdriver to tighten SCREWS (8) on LOCKNUT (6). Work your way around LOCKNUT (6), tightening the screws slightly each time until all are snug to ensure even pressure.
7 7
A B
SPOUT BASE
1
3
2
PUTTY
2
3
SINK OR
MOUNTING
SURFACE
8
4
5
6
8
4
5
6
2
MAKE WATER SUPPLY CONNECTIONS
Turn off hot and cold water supplies before beginning.
Connect FLEXIBLE SUPPLIES (1, 2) directly to wall supplies. Connection on fitting supplies are 3/8" compression. Connect left supply to Hot (Marked with a Red Line) and right supply to Cold wall supply. Use adjustable wrench to tighten connections.
Do not over tighten.
Faucet supplies are 21" long from faucet base.
Note: If additional supply length is required, installer must purchase additional parts separately.
Important: If SUPPLY HOSES (1, 2) are too long, loop as illustrated to avoid kinking.
3
INSTALL SPRAY HOLDER
On model with separate spray, place the SPRAY HOLDER (1) into the appropriate mounting hole. Assemble the SPRAY
HOLDER WING NUT (2) onto the shank of SPRAY HOLDER (1) from below and hand tighten. Do not use putty.
On model with spray through the ESCUTCHEON (3), place
SPRAY HOLDER (4) into the hole of ESCUTCHEON (3). Assemble
SPRAY HOLDER NUT (5) onto the shank of SPRAY HOLDER (4) from below and hand tighten. Do not use putty.
For installation less spray, cap off SPRAY HOSE
CONNECTION (9) with PIPE CAP (6).
SPRAY HOSE
CONNECTION
1
CONNECT HOSE SPRAY
Feed SPRAY HOSE (7) through SPRAY
HOLDER (1) and attach COUPLING NUT (8) of HOSE (7) to SPRAY HOSE CONNECTION (9) on valve body. Tighten COUPLING NUT (8) firmly.
4
5
4
TEST INSTALLED FAUCET
Move HANDLE down into "off" position and remove
AERATOR (1).
Turn on water supplies and check connections for leaks .
Operate HANDLE (2) up and down, left and right to flush water lines thoroughly.
For faucet with spray, direct SPRAY HEAD (3) into sink and activate SPRAY (3). Check hose connections for leaks.
Move HANDLE (2) down to "off" position and replace AERATOR (1).
3
9
6
1
HOT
2
8
COLD
2
3
1
7
2
CHECK CONNECTIONS
FOR LEAKS
M 9 6 8 4 6 9 R E V. 1. 6
5
SERVICE
Reduced flow. If the flow gradually reduces over a number of months, the AERATOR (12) may have collected debris.
To clean, remove AERATOR (12) and rinse with water and remove any debris. Turn on faucet to wash any debris out of the faucet. Thread AERATOR (12) back into spout. Operate faucet.
Spout leakage. If fitting leaks above or below SPOUT HUB remove SPOUT as follows and check SPOUT O-RINGS. First turn off water supply.
Remove HANDLE BUTTON (2) and loosen SET SCREW (1) with 2.5mm HEX
WRENCH (11) supplied. Pull HANDLE (3) off valve stem.
Pull off CAP (4). Loosen CARTRIDGE SCREWS (5) and remove CARTRIDGE (6).
Remove SPOUT (7) by pulling up gently while moving SPOUT (7) side to side.
Check both SPOUT O-RINGS (8) for damage. Replace if necessary.
On models with SPRAYS, DIVERTER (9) can be cleaned by pulling
DIVERTER (9) out of the MANIFOLD (10). Rinse clean the DIVERTER (9) and MANIFOLD (10). Push DIVERTER (9) back into MANIFOLD (10).
Reverse procedure to reinstall SPOUT, CARTRIDGE and HANDLE.
Clogged CARTRIDGE outlets or inlets may cause reduced flow.
To clean, first turn off water supply then:
Remove PLUG BUTTON (2), loosen HANDLE SCREW (1) and remove HANDLE (3).
Remove ESCUTCHEON CAP (4). Unscrew the three CARTRIDGE
SCREWS (5). Clean MANIFOLD (10), CARTRIDGE (6) ports and
SEALS (13).
Clean inlets of CARTRIDGE (6) and MANIFOLD (10).
Reassemble CARTRIDGE (6), alternately tightening SCREWS (5).
Replace CAP (4) and HANDLE (3). Check flow.
12
10
1
2
11
8
7
3
4
5
6
13
SPOUT
HUB
9
HOT LIMIT SAFETY STOP
By restricting handle rotation and limiting the amount of hot water allowed to mix with the cold, the HOT LIMIT
SAFETY STOP reduces risk of accidental scalding. To set the maximum hot water temperature of your faucets, all you need to do is adjust the setting on the HOT LIMIT
SAFETY STOP.
Remove HANDLE BUTTON (2) and loosen SET SCREW (1).
Pull HANDLE (3) off valve stem. Pull off CAP (4). Use a flat blade screwdriver or your fingers to pull up and rotate red
HOT LIMIT SAFETY STOP (5). Follow Step "A" or "B" to adjust min./max. discharge temperature. "0" being the hottest to "7" the coldest temperature setting.
"A"
PRY RED RING FORWARD
AND ROTATE COUNTER-
CLOCKWISE ONE CLICK
"B"
PRY RED RING FORWARD
AND ROTATE CLOCKWISE
1
0
"B"
ADJUSTMENT WHEN
WATER IS TOO COLD
"A"
ADJUSTMENT WHEN
WATER IS TOO HOT
5
1
2
3
4 "RED RING"- HOT
LIMIT SAFETY STOP
6
CARE INSTRUCTIONS:
DO: SIMPLY RINSE THE PRODUCT CLEAN WITH CLEAR WATER. DRY WITH A SOFT COTTON FLANNEL CLOTH.
DO NOT: DO NOT CLEAN THE PRODUCT WITH SOAPS, ACID, POLISH, ABRASIVES, HARSH CLEANERS, OR A
CLOTH WITH A COARSE SURFACE.
M 9 6 8 4 6 9 R E V. 1. 6
M962294-0070A
B U T T O N A N D
S C R E W K I T
M962338-YYY0A
HANDLE KIT
A907086-YYY0A
ESCUTCHEON CAP
042850-OO7OA
DIVERTER
M907552-YYY0A
ESCUTCHEON
M962298-0070A
SPACER AND SEAL
M962339-YYY0A
ESCUTCHEON AND
PUTTY PLATE
M962146-0070A
MOUNTING KIT
HOT LINE FOR HELP
For toll-free information and answers to your questions, call:
1-800-442-1902
Weekdays 8:00 a.m. to 6:00 p.m. EST
IN CANADA 1-800-387-0369 (TORONTO 1-905-306-1093)
Weekdays 8:00 a.m. to 7:00 p.m. EST
IN MEXICO 01-800-839-12-00
P r o d u c t n a m e s l i s t e d h e r e i n a r e t r a d e m a r k s o f A m e r i c a n S t a n d a r d I n c .
© A S A m e r i c a , I n c . 2 0 0 8
M918506-0070A
CARTRIDGE SCREWS
LAKELAND
®
SINGLE CONTROL KITCHEN
FAUCET WITH CAST SPOUT
MODEL NUMBERS
A951470-0070A
CARTRIDGE
4114.001
4114.001F15
M962296-YYY22OA (2.2 GPM)
SPOUT KIT
M962296-YYY15OA (1.5 GPM)
SPOUT KIT
066070-YYY0A (2.2 GPM)
AERATOR
M922881-YYY0A (1.5 GPM)
AERATOR
M962297-0070A
SPOUT SEAL KIT
(before 10/2012)
M964327-0070A
SPOUT SEAL KIT
(after 10/2012)
Replace the "YYY" with appropriate finish code
CHROME
STAINLESS STEEL
OIL RUBBED BRONZE
002
075
224
M962340-YYY0A
ESCUTCHEON WITH SPRAY
HOLE AND PUTTY PLATE
M961773-YYY0A
S P R AY H O L D E R
( 3 - H O L E )
M953667-YYY0A
HANDSPRAY & HOSE
M953040-YYY0A
SPRAY HOLDER
060341-0070A
PIPE CAP
M 9 6 8 4 6 9 R E V. 1. 6
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project