Cembre ROLLY2000 990910 Thermal transfert printer on roll Operation and Maintenance Manual

Add to my manuals
28 Pages

advertisement

Cembre ROLLY2000 990910 Thermal transfert printer on roll Operation and Maintenance Manual | Manualzz

09 M 103 E

1

Certified Quality

Management System

Certified Environmental

Management System

Certified Occupational

Health & Safety

Management System

ENGLISH

OPERATION AND MAINTENANCE

MANUAL

2

marking system from Cembre is designed for the volume printing of cables markers and adhesive labels.

Robust and quiet, Rolly2000 provides reliable, intensive operation in office or factory combined with the facility to optimise printer set-up according to the media.

Print area: maximum width 105 mm - maximum length 2000 mm

The printer is equipped with a power unit suitable for supply voltages 230 V~ / 50 Hz or 115 V~ / 60 Hz without adjustment.

Width

242 mm

Printer size and weight

Height Length

274 mm 446 mm

Weight

9 kg

MINIMUM SYSTEM REQUIREMENTS:

• PC with dual Core processor or equivalent

• 2 Gb RAM memory

• 2 Gb of available space on the hard disc

• 1280x1024 SVGA monitor resolution.

• Windows XP SP3, VISTA, 7 and 8 operating systems.

• USB Port for local installation

• Ethernet Port for network installation

Trademark

Centronics ® is a registered trademark of the Data Computer Corporation.

Microsoft ® is a registered trademark of the Microsoft Corporation.

Windows XP ® , Vista ® , 7 ® , 8 ® are registered trademarks of the Microsoft Corporation.

Table of Contents

1 Introduction ............................................................................................................................................ 4

1.1 Instructions ............................................................................................................................................... 4

1.2 Intended Use ............................................................................................................................................ 4

1.3 Safety Instructions .................................................................................................................................... 4

1.4 Environment ............................................................................................................................................. 5

2 Installation .............................................................................................................................................. 6

2.1 Device overview ....................................................................................................................................... 6

2.2 Unpacking and setting-up the printer ....................................................................................................... 8

2.3 Connecting the device .............................................................................................................................. 8

2.3.1

2.3.2

Connecting to the power supply ......................................................................................................... 8

Connecting to a computer or computer network................................................................................. 8

2.4 Powering up the device ............................................................................................................................ 8

3 Control panel .......................................................................................................................................... 9

3.1 Structure of the control panel and language setting ................................................................................. 9

3.1.1

3.1.2

Key functions ...................................................................................................................................... 9

Setting the different language ............................................................................................................ 9

3.2 Symbol displays ....................................................................................................................................... 9

3.3 Printer states .......................................................................................................................................... 10

3.4 Key functions ...........................................................................................................................................11

4 Loading material .................................................................................................................................. 12

4.1 Loading labels from roll ( TTL...; TPM-ROLL...: KM-ROLL...; TTF...) ..................................................... 12

4.1.1

4.1.2

4.1.3

4.1.4

4.1.5

Removing and installing the core adapters ...................................................................................... 12

Positioning the label roll on the roll retainer...................................................................................... 13

Inserting a label strip into the printhead............................................................................................ 13

Setting the label sensor .................................................................................................................... 14

Setting the head locking system ....................................................................................................... 15

4.2 Loading ribbon ....................................................................................................................................... 16

4.3 Setting the feed path of the ribbon ......................................................................................................... 17

5 Cleaning ................................................................................................................................................ 18

5.1 Cleaning information .............................................................................................................................. 18

5.2 Cleaning the print roller .......................................................................................................................... 18

5.3 Cleaning the printhead ........................................................................................................................... 18

5.4 Cleaning the label sensor ....................................................................................................................... 19

6 Troubleshooting ................................................................................................................................... 20

6.1 Types of errors ....................................................................................................................................... 20

6.2 Problem solution .................................................................................................................................... 20

6.3 Error messages and fault correction ...................................................................................................... 21

7 Media ..................................................................................................................................................... 23

7.1 Media dimensions .................................................................................................................................. 23

7.2 Device dimensions ................................................................................................................................ 24

7.3 Reflex mark dimensions ......................................................................................................................... 25

7.4 Cut-out mark dimensions ....................................................................................................................... 26

8 Conformity ............................................................................................................................................ 27

9 Warranty ................................................................................................................................................ 27

10 Return to Cembre for repair ................................................................................................................ 27

11 Accessories .......................................................................................................................................... 27

3

4

1 Introduction

1.1 Instructions

Important information and instructions in this documentation are designated as follows:

Danger!

Draws your attention to an exceptionally grave, impending danger to your health or life.

!

Warning!

Indicates a hazardous situation that could lead to injuries or material damage.

!

Attention!

Draws attention to possible dangers, material damage or loss of quality. i

Notice!

Gives you tips. They make a working sequence easier or draw attention to important working processes.



Environment!

Gives you tips on protecting the environment.

Handling instruction

Reference to section, position, illustration number or document.

 Option (accessories, peripheral equipment, special fittings).

Time Information in the display.

1.2 Intended use

• The device is manufactured in accordance with current technological status and recognised safety rules.

However, danger to the life and limb of the user or third parties and/or damage to the device and other tangible assets can arise during use.

• The device may only be used for its intended purpose and if it is in perfect working order, and it must be used with regard to safety and dangers as stated in the operating manual.

• The device is intended exclusively for printing suitable materials that have been approved by the manufacturer.

Any other use or use going beyond this shall be regarded as improper use. The manufacturer/supplier shall not be liable for damage resulting from unauthorised use; the user shall bear the risk alone.

• Usage for the intended purpose also includes complying with the operating manual, including the manufacturer‘s maintenance recommendations and specifications.

i

Notice!

The complete documentation is included in the CD, and can also be found the Internet.

1.3 Safety instructions

• The device is configured for voltages of 100 to 240 V AC. It only has to be plugged into an earthed socket.

• Only connect the device to other devices which have a protective low voltage.

• Switch off all affected devices (computer, printer, accessories) before connecting or disconnecting.

• The device may only be used in a dry environment, do not expose it to moisture (sprays of water, mists, etc.).

• Do not use the device in an explosive atmosphere.

• Do not use the device close to high-voltage power lines.

• If the device is operated with the cover open, ensure that people‘s clothing, hair, jewelry etc. do not come into contact with the exposed rotating parts.

• The device or parts of it can become hot while printing. Do not touch during operation, and allow to cool down before changing material and before disassembly.

1 Introduction

• Risk of crushing when closing the cover. Keep fingers outside when moving the device cover.

• Perform only those actions described in this operating manual.

Work going beyond this may only be performed by trained personnel or service technicians.

• Unauthorised interference with electronic modules or their software can cause malfunctions.

• Other unauthorised work on or modifications to the device can also endanger operational safety.

• Always have service work done in a qualified workshop, where the personnel have the technical knowledge and tools required to do the necessary work.

• There are various warning stickers on the device. They draw your attention to dangers.

Warning stickers must therefore not be removed, as then you and other people cannot be aware of dangers and may be injured.

• The maximum sound pressure level is less than 70 dB(A).

Danger!

Danger to life and limb from power supply.

 Do not open the device casing.

1.4 Environment

 

Obsolete devices contain valuable recyclable materials that should be sent for appropriate processing.

The modular construction of the printer enables it to be easily disassembled into its component parts.

 Send the parts for recycling.

5

Following information applies in member states of the European Union:

 USER INFORMATION in accordance with “Directives 2002/95/EC and 2002/96/EC regarding the reduction of hazardous substances in electrical and electronic equipment, including the disposal of waste”.

The 'Not in the bin' symbol above when shown on equipment or packaging means that the equipment must, at the end of its life, be disposed of separately from other waste.

The separate waste collection of such equipment is organised and managed by the manufacturer.

Users wishing to dispose of such equipment must contact the manufacturer and follow the prescribed guidelines for its separate collection.

Appropriate waste separation, collection, environmentally compatible treatment and disposal is intended to reduce harmful environmental effects and promote the reuse and recycling of materials contained in the equipment.

Unlawful disposal of such equipment will be subject to the application of administrative sanctions provided by current legislation.

The electronic circuit board of the device is equipped with a lithium battery.

 Take old batteries to appropriate collection centres.

6

2 Installation

2.1 Device overview

10

9

8

Fig. 1 Overview

3

4

5

6

7

1

2

1 Cover

2 Core adapter

3 Margin stop

4 Roll retainer

5 Ribbon supply hub

6 Ribbon take-up hub

7 Print mechanics

8 Mounting area for accessories incl. peripheral connector

9 Navigator pad

10 Display

17

18

19

20

16

12

13

14

15

12 Ribbon guide

13 Printhead locking screw

14 Printhead retainer with printhead

15 Print roller

16 Allen key

17 Printhead locking lever

18 Plate

19 Axle with guide ring

20 Label sensor

Fig. 2 Print mechanics

2 Installation

Fig. 3 Connections

26

27

28

29

30

23

24

25

23 Power switch

24 Power connection socket

25 Slot for PC Card Type II

26 Slot for CompactFlash memory card

27 Ethernet 10/100 Base-T

28 2 USB master ports for keyboard, scanner or service key

29 USB high-speed port

30 Serial RS-232 C port

7

8

2 Installation

2.2 Unpacking and setting-up the printer

 Lift the label printer out of the box via the straps.

 Check label printer for damage which may have occurred during transport.

 Place the printer on a level surface.

 Check delivery for completeness. i

Contents of delivery:

• Label printer

• USB cable

• Power cable

• Black printer ribbon type TPS-060 842112 already fitted into the printer

• Protective cover

• Operating software on "GENIUSPRO" CD

• Documentation

Notice!

Please keep the original packaging in case the printer needs to be returned or transported.

!

Attention!

The device and printing materials will be damaged by moisture.

 Set up label printers only in dry locations protected from splash water.

2.3 Connecting the device

The standard available interfaces and connectors are shown in figure 3.

2.3.1 Connecting to the power supply

The printer is equipped with a power unit suitable for supply voltages 230 V~ / 50 Hz or 115 V~ / 60 Hz without adjustment.

Check that the device is switched off.

1. Plug the power cable into the power connection socket (6).

2. Plug the power cable into an earthed socket.

2.3.2 Connecting to a computer or computer Network

!

Attention!

Inadequate or no earthing can cause malfunctions during operations.

Ensure that all computers and cables connected to the label printer are grounded.

 Connect the label printer to a computer or network an appropriate cable.

2.4 Powering up the device

23

When all connections have been made:

 Switch the printer on at the power switch (23).

The printer performs a system test, and then shows the system status ready in the display (11).

If an error occurs during the system test, the symbol and type of error are displayed.

Fig. 4 Power-on

3 Control panel

3.1 Structure of the control panel

The user can control the operation of the printer with the control panel.

1

Ready

6

The control panel consists of a graphic display (1) and the navigator pad (2) with five integrated keys.

The graphic display indicates the current status of the printer and the print job, indicates faults and shows the printer settings in the menu.

9

1

2

2

In Linea

1

6

Fig. 5 Control panel

3.1.1 Key functions

The navigator pad (2) allows access to menus for perameter setting.

2

Keys Menu

In Linea

 Return from a submenu

6

 Jump into a submenu

| Menu option to the left

 Menu option to the right

Start of a selected menu option

Hold 2 s: Leaving the offline menu

Table 2 Key functions

Fig. 6 Navigator pad

Parameter setting

Parameter choice Numeric value

-

-

Increase the number at the cursor position

Decrease the number at the cursor position

Cursor shift to the left left right Cursor shift to the right

Confirmation of the selected value

Hold 2 s: Abort without changing the value

3.1.1 Setting the different language

As default the display is set the ENGLISH language.

To set a different language, make use of the navigator pad and select:

Menu >  Setup >  Local settings >  Country >   ... Language > 

10

3 Control panel

3.2 Symbol displays

The symbols shown in the following table may appear in the status line of the display, depending on the printer configuration. They enable the current printer status to be seen quickly.

Symbol Description

Clock

Date

Date/time digital

Ribbon supply

Wi-Fi signal strength

Table 2 Symbol displays

Symbol Description

Ethernet link status

Temperature of the printhead

PPP funds

Debug window for abc programs

Control of the lower display line is handed over to an abc program

Symbol Description

User memory in the clock circuit

Used memory

Input buffer

Access to memory card

Printer is receiving data

3.3 Printer States

State

Ready

Printing label

Pause

Recoverable error

Irrecoverable error

Critical error

Power Save Mode

Display

Ready and configured symbol displays, such as time and date

Printing label and the number of the printed label in the print job.

Pause and the symbol and the type of error printed.

and the number of labels still to be and the type of error and the number of labels still to be printed.

and the type of error

Description

The printer is in the ready state and can receive data.

The printer is currently processing an active print job.

Data can be transmitted for a new print job.

The new print job will start when the previous one has finished.

The printing process has been interrupted by the operator.

An error has occurred that can be rectified by the operator without interrupting the print job.

The print job can be continued after the error has been rectified.

An error has occurred that cannot be rectified without interrupting the print job. and the key lighting is switched off

An error occurs during the system test.

 Switch the printer off and then on again at the power switch or

 Press cancel key.

Call Cembre if the fault occurs persistently.

If the printer is not used for a lengthy period, it automatically switches to power save mode.

 To exit power save mode: Press any key on the navigator pad.

Table 3 Printer states

3 Control panel

3.4 Key functions

The key functions depend on the current printer state:

- Active functions: Labels and symbols on the navigator pad keys light up.

- Active functions light up white in print mode (e. g. menu or feed).

- Active functions light up orange in the offline menu (arrows, key  ).

Key menu lights feed lights

pause lights

Display

Ready

Ready

Ready

State

Ready

Ready

Ready

Printing label Printing label

Pause Pause flashes Recoverable error

cancel lights Ready Ready flashes lights

Printing label Printing label

Pause Pause

Recoverable error

Irrecoverable error

Error 

Table 3 Key functions in the print mode

Function

To the offline menu

Feeds a blank label

After the end of a print job, reprint the last label

Interrupt print job, printer goes into "Pause" state

Continue the print job, printer goes into "Printing label" state

Continue the print job after rectifying the error, printer goes into "Printing label" state

Delete internal memory, the last label can no longer be reprinted.

Short press g cancels the current print job

Longer press g cancels the current print job and deletes all print jobs

Call Help - Concise information for rectifying the fault will be displayed

11

12

4 Loading material

4.1 Loading labels from roll

4.1.1 Removing and installing the core adapters

Core adapters are mounted for better guidance of the label roll on the roll retainer when using label rolls with a core diameter ≥ 75 mm.

 Remove core adapters for smaller label rolls as follows.

1

2

3

4

5

2

6

Fig. 8 Core adapter unfixed (left) and fixed (right)

7

5

2

Fig. 7 Core adapters and margin stop

Fig. 9 Margin stop unfixed (left) and fixed (right)

Removing the core adapters

1. Open cover.

2. Turn ring (5) at the margin stop (4) counterclockwise, so that the arrow (7) points to the symbol , and thus release the margin stop.

3. Remove the margin stop (4) from the roll retainer (2).

4. Turn the rings at the adapters (1,3) counterclockwise and thus release the adapters.

5. Remove the adapters (1,3) from the roll retainer (2).

6. Re-mount the margin stop (4) onto the roll retainer (2), turn ring (5) clockwise, so that the arrow (7) points to the symbol , and thus fix the margin stop (4) on the roll retainer.

Installing the core adapters

1. Open cover.

2. Turn ring (5) at the margin stop (4) counterclockwise, so that the arrow (7) points to the symbol , and thus release the margin stop.

3. Remove the margin stop (4) from the roll retainer (2).

4. Align the guide lugs (6) in the core adapters (1,3) with the grooves in the roll retainer (2) an push the adapters onto the roll retainer.

5. Slide first core adapter (1) to the chassis until it stops and fix the adapter by turning the ring clockwise.

6. Place second core adapter (3) matching to the roll width and fix it by turning the ring clockwise.

7. Re-mount the margin stop (4) onto the roll retainer (2), turn ring (5) clockwise, so that the arrow (7) points to the symbol , and thus fix the margin stop (4) on the roll retainer.

4 Loading material

4.1.2 Positioning the label roll on the roll retainer

!

Attention!

To guarantee good condition of the labels it is suggested to keep the rolls in their original packing at a normal, even temperature; do not touch the underside of the print head with fingers or pointed objects.

 Remove labels from the packing only when used and do not expose the materials to humidity for a long period.

13

9

8

7

6

1

2

3

4

Fig. 10 Loading labels from roll

1. Open cover (9).

2. Turn ring (2) at the margin stop (1) counterclockwise, so that the arrow points to the symbol , and thus release the margin stop.

3. Remove the margin stop (1) from the roll retainer (4).

4. Load label roll (3) on the core adapters ( 4.1.1 on page 12) in such a way that the labels can be inserted into the printhead in the right position. The printing side of the labels must be visible from above.

5. Re-mount the margin stop (1) onto the roll retainer (4). Push the margin stop (1) to the roll until it stops.

6. Turn ring (2) clockwise, so that the arrow (10) points to the symbol , and thus fix the margin stop (1) on the roll retainer (4).

4.1.3 Inserting a label strip into the printhead

1. Turn lever (8) counterclockwise to lift the printhead.

2. Push red guide ring on to axle (6) all the way out.

3. Guide label strips below the axle (6) and through the label sensor (7) in such a way that it exits the print unit between the printhead and the print roller.

4. Push guide ring on to axle (6) against the outer edge of the label strip.

14

4 Loading material

4.1.4 Setting the label sensor

!

Attention!

Adjustment of the label sensor is essential to the correct advancement of the printing material.

1 2

1

3

Fig. 11 Setting the label sensor

The sensor case (2) can be shifted perpendicular to the direction of material flow for adaptation to the label medium.

The label sensor (1) is visible from the front through the print unit and is marked with a indentation in the case retainer.

 Position label sensor with tab (3) in such a way that the sensor (1) can detect the label gap or a join reflex or

perforation.

In Figures 12 and 13 there are some examples showing the right positioning of the label sensor (1) depending on the type of material being printed.

KM-ROLL..... (*)

ETF-ROLL.....

TTL.....

TPM-ROLL.....

LABEL SENSOR

POSITION

LABEL SENSOR

POSITION

Fig. 12 Examples of label sensor setting

LABEL SENSOR

POSITION

LABEL SENSOR

POSITION

(*) Some versions of cable markers KM-ROLL are equipped with a transversal black line mark instead the lateral perforation mark, in such a

TTF...

STRIP-ROLL...

TTL....

LABEL SENSOR

POSITION

LABEL SENSOR

POSITION

LABEL SENSOR

POSITION

TTL.....

TPM-ROLL.....

ETF-ROLL.....

KM-ROLL..... (*)

4 Loading material

material.

LABEL SENSOR

POSITION

LABEL SENSOR

POSITION

For non-recangular labels (e.g. TTL circular), position the label sensor (1) on the central axis.

TTF...

STRIP-ROLL...

TTL....

LABEL SENSOR

POSITION

15

LABEL SENSOR

POSITION

Fig. 13 Examples of label sensor setting

LABEL SENSOR

POSITION

LABEL SENSOR

POSITION

4.1.5 Setting the print head locking system

!

Attention!

Usually no adjustment is required, so proceed with caution as incorrect setting may move the plungers printhead from its optimum position, reducing print quality and possibly damaging the printer.

The printhead has a three point locking system which is factory set in order to:

• achieve even print quality across the entire label width

• prevent creases in the feed path of the ribbon

• prevent premature wearing of the print roller and printhead.

1

2

3

Fig. 14 Setting the print head locking system

16

4 Loading material

4.2 Loading ribbon

i

Notice!

The printer is supplied with a ribbon already installed, to replace it proceed as follow.

1 2 3 4

5

Fig. 15 Feed path of the ribbon

1. Clean printhead before loading the ribbon ( 5.3 on page 18).

2. Turn lever (5) counterclockwise to lift the printhead.

3. Slide ribbon roll (3) onto the ribbon supply hub (4) until it stops and so that the colour coating of the ribbon faces downward when being unwound.

4. Hold ribbon roll (3) firmly and turn knob on ribbon supply hub (4) counterclockwise until the ribbon roll is secured.

5. Slide suitable transfer ribbon core (1) onto the ribbon take-up hub (2) and secure it in the same way.

6. Guide ribbon through the print unit as shown in Fig. 15.

7. Secure starting end of transfer ribbon to the transfer ribbon core (1) with adhesive tape. Ensure counterclockwise rotation direction of the transfer ribbon take-up hub.

8. Turn ribbon take-up hub (2) counterclockwise to smooth out feed path.

9. Turn lever (5) clockwise to lock the printhead.

4 Loading material

4.3 Setting the feed path of the ribbon

Creases in the ribbon can cause printing problems. Adjust the ribbon guide to minimise creasing.

i

Notice!

Adjustment of the head locking system may also prevent ribbon creasing ( 4.1.5 on page 15).

2

1

17 i

Fig. 16 Setting the feed path of the ribbon

Notice!

Adjustment is best carried out during printing.

1. Read current setting on the scale (1) and record if necessary ( Fig. 16).

2. Adjust screw (2) with Allen key and observe the behavior of the ribbon.

In the + direction, the inner edge of the ribbon is tightened, the outer edge is tightened in the - direction.

!

The printer is ready for operation when all connections have been made and labels and the transfer ribbon have been loaded.

Attention!

Printhead damage can be caused by incorrect handling!

 Do not touch the underside of the printhead with the fingers or sharp objects.

 Ensure that the labels are clean.

 Ensure that the label surfaces are smooth. Rough and uneven media will reduce the service life of the printhead.

 Print with the lowe st possible printhead temperature.

18

5 Cleaning

5.1 Cleaning information

Danger!

Risk of death via electric shock!

 Disconnect the printer from the power supply before performing any maintenance work.

The printer requires very little maintenance.

It is important to clean the printhead regularly to acheive a consistently good print quality and minimise premature wear of the printhead.

Otherwise, the maintenance is limited to keeping the device clean, both inside and out.

!

!

Attention!

The printer can be damaged by aggressive cleansers.

Do not use abrasive cleaners or solvents for cleaning the external surfaces.

 Remove dust and debris from the print area with a soft brush or vacuum cleaner.

 The cover of the printer can be cleaned with a standard cleanser.

5.2 Cleaning the print roller

Accumulation of dirt on the print roller may impair the media flow and the print quality.

 Lift the printhead.

 Remove media and ribbon from the printer.

 Remove deposits with roller cleaner and a soft cloth.

 If the roller appears damaged, replace it  Contact Cembre.

5.3 Cleaning the printhead

Cleaning frequency: every ribbon change

Contamination may accumulate on the printhead during printing and adversely affect print, e.g. differences in contrast or vertical stripes.

!

Attention!

Printhead can be damaged!

Do not use sharp or hard objects to clean the printhead.

Do not touch protective glass layer of the printhead.

Attention!

Risk of injury from the hot printhead.

Ensure that the printhead has cooled down before cleaning it.

 Lift the printhead.

 Remove media and ribbon from the printer.

 Clean printhead surface with special cleaning pen or a cotton swab dipped in pure alcohol.

 Allow printhead to dry for 2–3 minutes before recommencing printing.

5 Cleaning

5.4 Cleaning the label sensor

!

Attention!

Label sensor can be damaged!

Do not use sharp or hard objects or solvents to clean the label sensor.

The label sensor can become contaminated. This can adversely affect label detection.

1

2

3

4

Fig. 17 Cleaning the label sensor

1. Turn lever (1) counterclockwise to lift the printhead.

2. Remove media and ribbon from the printer.

3. Press the latch (3) and slowly pull label sensor outward via the tab (4). Ensure that the label sensor cable is not stretched during this operation.

4. Clean label sensor and sensor units (2) with brush or cotton swab soaked in pure alcohol.

5. Push label sensor back via tab (3) and set it ( 4.1.4 on page 14).

6. Reload media and ribbon.

19

20

6 Troubleshooting

6.1 Types of error

The diagnostic system indicates on the screen if an error has occurred. The printer is set into one of the three possible error states according to the type of error.

State

Recoverable error

Irrecoverable error

Display Key

pause flashes

cancel lights

cancel flashes

Remark

 3.4 on page 11

Critical fault -

Table 5 Error states

6.2 Problems and solutions

Problem

Ribbon creases

Print has smears or voids

Printer only prints every second label

Vertical white lines in the print

Cause

Ribbon guide not adjusted

Printhead locking system not adjusted

Transfer ribbon too wide

Printhead is dirty

Printer does not stop after ribbon runs out

Printer prints a sequence of characters instead of the label format

Printer transports media, but ribbon does not move

Temperature too high

Incompatible combination of media and ribbon

Thermal printing driver selected

Printer is in ASCII dump mode

Ribbon incorrectly inserted.

Set the printer to "Thermal transfer" via driver.

Cancel ASCII dump mode.

Check and, if necessary, correct the ribbon web and the orientation of the media.

Incompatible combination of media and ribbon

Use only Cembre media and ribbon.

Setting of size in the software is too large. Change the size in the software.

Printhead is dirty

Remedy

Adjust the ribbon guide.

 4.3 on page 17

Adjust the printhead locking system.

 4.1.5 on page 15

Use a transfer ribbon slightly wider than the width of label.

Clean the printhead

 5.3 on page 26

Decrease temperature via driver.

Use only Cembre media and ribbon.

Horizontal white lines in the print

Print is irregular, one side is lighter

Printhead is defective (failure of heat elements)

Printer is used with the backfeed > smart in the cut or peel-off mode

Printhead is dirty

Head locking system not adjusted

Clean the printhead

 5.3 on page 18

Change the printhead.

 please contact Cembre

Set the backfeed > always in setup.

Clean the printhead

 5.3 on page 18

Adjust the head locking system.

 4.1.5 on page 15

Table 6 Problems solutions

6 Troubleshooting

6.3 Error messages and fault correction

Error message

ADC malfunction

Battery low

Buffer overflow

Card full

Cutter blocked

Cause

Hardware error

Battery the PC card is flat

The input buffer memory is full and the computer is still transmitting data.

No more data can be stored on the memory card

Cutter cannot return to its home position and stays in an undefined position

Remedy

Switch the printer off and then on.

If error recurs call Cembre.

Replace battery on the PC card.

Use data transmission via protocol

(preferably RTS/CTS).

Replace card.

Cutter jammed

No cutter function

Device not conn. Programming addresses a non-existent device

File not found

FPGA malfunction Hardware error

Head error

Head open

Head too hot

Invalid setup

Memory overflow

Name exists

The cutter is unable to cut the labels but is able to return into its home position

Requested file is not on the memory card

Hardware error

Printhead not locked

Printhead is overheated

Error in the configuration memory

Switch off the printer. Remove material.

Switch on the printer. Restart print job.

Change material.

Switch the printer off and then on.

If error recurs call Cembre.

Press the cancel key.

Change material.

Either connect this device or correct the programming.

Check the contents of the memory card.

Switch the printer off and then on.

If error recurs call Cembre.

Switch the printer off and then on.

If error recurs replace printhead.

Lock printhead.

After pausing, the print job will be continued automatically. If the fault recurs repeatedly, decrease head temperature (darkness option) or the print speed via driver.

Re-configure printer.

If error recurs call Cembre.

Cancel current print job.

Reduce amount of data to be printed.

Correct programming

No DHCP server

No label found

No label size

No Link

No record found

Current print job contains too much information, e.g. selected font, large graphics

Duplicate usage of field name in the direct programming

The printer is configured for DHCP, but there is no DHCP server, or the DHCP server is not currently available.

There are labels missing on the label material

The label format as set in the software does not correspond with the real label format

Printer is loaded with continuous material, but the software is set on labels

The size of the label is not defined in the program.

No network link

Refers to the optional memory card; database access error

Switch off DHCP in the configuration, and assign a fixed IP address.

Please contact your network administrator.

Press pause key repeatedly until printer recognizes the next label on the material.

Cancel current print job.

Change the label format set in the software.

Restart print job.

Cancel current print job.

Set the sensor type --> continuous via driver.

Restart the print job.

Check program.

Check network cable and connector.

Please contact your network administrator.

Check program and card contents.

21

22

6 Troubleshooting

Error message

No SMTP server

Cause

The printer is configured for SMTP, but there is no SMTP server, or the SMTP server is not currently available.

Remedy

Switch off SMTP in the configuration.

Caution! Disable sending a warning by e-mail (EAlert).

Please contact your network administrator.

Switch off Timeserver in the configuration.

Please contact your network administrator.

No Timeserver

Out of paper

Out of ribbon

Timeserver is selected in the configuration, but there is no Timeserver, or the

Timeserver is not currently available.

Media has run out

Ribbon has run out

Ribbon melted during printing

Protocol error Printer has received an unknown or invalid command from the computer.

Read error Read error when reading from the memory card

Remove ribbon Transfer ribbon is loaded although the printer is set to direct thermal printing

Structural err.

Error in the file list of the memory card, data access is uncertain.

Unknown card Card not formatted,

Type of card not supported

USB error

Device stalled

USB error

Too much current

USB error

Unknown device

Voltage error

A USB device has been detected, but it is not working.

The USB device consumes too much current.

Failure to detect USB device

Hardware error

Load media.

Check paper feed.

Insert new ribbon.

Cancel current print job.

Change the head temperature via driver

(darkness option).

Clean the printhead  5.3 on page 18

Load ribbon

Restart print job.

Press the pause key to skip the command or press the cancel key to cancel the print job.

Check data of the card.

Backup data, reformat card.

Set the printer to "Thermal transfer" via driver.

Format memory card.

Format card, use different type of card.

Do not use the USB device.

Do not use the USB device.

Do not use the USB device.

Write error Hardware error

Write protected PC card write protection is activated.

Wrong revision Firmware not compatible with the hardware version

Switch the printer off and then on.

If error recurs call Cembre.

Voltage at failure is shown. Please note.

Repeat the write process, reformat card.

Deactivate write protection.

 please contact Cembre

Table 7 Error Messages and fault correction

7 Media

7.1 Media dimensions

Labels Continuous material

23

Fig. 18 Label / continuous material dimensions

Dim. Designation Dim. en mm

-

-

B

H

-

A

C

Label width

Label height

Tear-off length

Cut length

with cutter

with perforation cutter

Dl Left margin

Dr Right margin

E

F

Perforation length

Label distance

Width of liner or continuous material

Media thickness

Liner thickness

4 - 116

4 - 1000

> 30

> 2

> 12

> 2

> 2

25 - 120

≥ 0

≥ 0

0,025 - 0,7

0,03 - 0,1

G Thickness of media with liner

Q Thickness continuous material

V Label feed

0,055 - 0,8

0,03 - 0,8

> 6

• Small label sizes, thin materials or strong adhesive can lead to limitations.

Critical applications should to be tested before production.

• Note the bending stiffness ! Material must be flexible to follow the radius of the print roller !

Table 8 Label / continuous material dimensions

24

7 Media

7.2 Device dimensions

Gap sensor

& Reflective sensor

Printhead

Peel-off edge

Tear-off edge

Cut edge

Fig. 19 Device dimensions

Dim. Designation

IP Distance printhead - peel-off edge

IC Distance printhead - cut edge

IT Distance printhead - tear-off edge

J Distance 1st printing point - material edge

K Print width with printhead 300 dpi

SX Distance gap/reflective sensor - material edge i.e. permissible distance of reflex or cut-out marks to the material edge

SY Distance gap/reflective sensor - printhead

Dim. en mm

13,5

18,8

13,5

2

105,6

5 - 53

46,0

Table 9 Device dimensions

7 Media

7.3 Reflex mark dimensions

Labels with reflex marks Endless material with reflex marks virtual label front edge reflex mark

Fig. 20 Reflex mark dimensions

Dim. Designation

A Label distance

L Width of reflex mark

M Height of reflex mark

X

Z

Distance mark - material edge

Distance virtual label front edge - actual label front edge

 Adjust software settings

• Reflex marks must be on the liner side of the material.

• Specification is valid for black marks.

• Recognition of colorued marks may fail.  Preliminary tests are needed.

Table 10 Reflex mark dimensions

Dim. en mm

> 2

> 5

3 - 10

5 - 53

0 up to A / recomm. : 0

25

26

7 Media

7.4 Cut-out mark dimensions

Labels with cut-out marks Continuous material with cut-out marks

for marginal cut-out marks minimum liner thickness 0,06 mm

Fig. 21 Cut-out mark dimensions

Dim. Designation

A Label distance

N Width of cut-out mark for marginal cut-out

P Height of cut-out mark

X Distance mark - material edge

Y Sensor recognised virtual label front edge with gap sensor

Z Distance recognised front edge - actual label front edge

 Adjust software settings

Table 11 Cut-out mark dimensions

Dim. in mm

> 2

> 5

> 8

2 - 10

5 - 53

Rear edge cut-out

0 up to A-P

Marginal cut-out Long hole cut-out Rectangular cut-out Circular cut-out

Cut-out between the labels

Not recommended !

Not recommended !

Fig. 26 Samples for cut-out marks

8 Conformity

• CE marked in compliance with 2006/42/EC, 2006/95/EC and 2004/108/EC European directives

• FCC Requirements of the FCC regulations part 15 for class A computers.

Under disadvantageous circumstances, the operation of these devices may cause interference with radio or TV reception, which has to be eliminated by the operator.

9. Warranty

Rolly2000 is guaranteed for one year against inherent faults and defects.

The print head and the print roller are classed as consumable items and not covered by the guarantee.

The guarantee is void if non-Cembre original items are used in this printer.

10. Return to Cembre for repair

In the case of a breakdown contact our Area Agent who will advise on the problem and provide the necessary instructions on how to dispatch the printer to our nearest Service Centre; if possible, attach a copy of the Test Certificate supplied by

Cembre together with the printer or, if no other references are available, indicate the approximate purchase date and serial number.

11. Accessories

Rolly2000-cutter 990856: fits to front of printer.

Automatically cuts to length continuous TTL... and flexible

TTF material

27

 TPS-060 printer ribbons: premium quality ribbon provide resin based indelible print in accordance with the scratch and abrasion resistance requirements of CEI 16-7.

Lenght 200 m, Width 112 mm. Print width 105 mm.

Colour

black

blue

red

green

white

silver

Description

Re. PANTONE® Black C

Ref. PANTONE® 2935 C

Ref. PANTONE® 186 C

Ref. PANTONE® 354 C

Code

842112

842113

842115

842114

842122

842116

28

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals