Tourney (настройка трансмиссии)

Tourney (настройка трансмиссии)
SI-RS41E
Technical Service Instructions
Tourney
General Safety Information
WARNING
• Use neutral detergent to clean the chain. Do not use alkali-based or acid based detergent
such as rust cleaners as it may result in damage and/or failure of the chain.
• Use the reinforced connecting pin only for connecting the narrow type of chain.
• There are two different types of reinforced connecting pin available. Be sure to check the
table below before selecting which pin to use. If connecting pins other than reinforced
connecting pins are used, or if a reinforced connecting pin or tool which is not suitable for
the type of chain is used, sufficient connection force may not be obtained, which could
cause the chain to break or fall off.
Chain
9-speed super narrow
chain such as
CN-7701 / CN-HG93
8- / 7- / 6-speed narrow
chain such as
CN-HG50 / CN-IG51
Reinforced
connecting pin
Chain tool
Silver
TL-CN31 / TL-CN22
Black
TL-CN31 / TL-CN22 and
TL-CN30 / TL-CN21
6.5mm
7.1mm
Reinforced
• If it is necessary to adjust the length of the chain
End Pin
Link Pin
Connecting Pin
due to a change in the number of sprocket teeth,
make the cut at some other place than the place
where the chain has been joined using a
reinforced connecting pin or an end pin. The chain
will be damaged if it is cut at a place where it has been joined with a reinforced connecting
pin or an end pin.
• Be careful not to let the cuffs of your clothes get caught in the chain while riding, otherwise
you may fall off the bicycle.
• Check that the tension of the chain is correct and that the chain is not damaged. If the
tension is too weak or the chain is damaged, the chain should be replaced. If this is not
done, the chain may break and you may fall off the bicycle.
• Check that there are no cracks in the crank arms before riding the bicycle. If there are any
cracks, the crank arm may break and you may fall off the bicycle.
• Check that the wheels are fastened securely before riding the bicycle. If the wheels are
loose in any way, they may come off the bicycle and serious injury may result.
• Obtain, read and carefully service instructions when installing parts. A loose, worn, or
damaged parts may cause injury to the rider.
We strongly recommend that only genuine Shimano replacement parts be used.
• Read these Technical Service Instructions carefully, and keep them in a safe place for later
reference.
RA-A
E
C
DU
Note
• FD-TY15-GS / TY18 / TZ31 / TZ30 are Non SIS compatible, and cannot be used in
combination with the SL-RS41-L.
• Apply grease to the thread section of the bottom bracket and to the inside thread of the
adapter before installing the bottom bracket.
• In addition, if pedaling performance does not feel normal, check this once more.
• Check that there is no looseness in any joints or connections before riding the bicycle. (BBFC, FC-PD)
• Do not wash the bottom bracket with high-pressure jets of water.
• If you feel any looseness in the bottom bracket axle, the bottom bracket should be replaced.
• If gear shifting operations do not feel smooth, wash the derailleur and lubricate all moving
parts.
• If the amount of looseness in the links is so great that adjustment is not possible, you
should replace the derailleur.
• You should periodically clean the derailleur and lubricate all moving parts (mechanism and
pulleys).
• If gear shifting adjustment cannot be carried out, check the degree of parallelism at the rear
end of the bicycle. Also check if the cable is lubricated and if the outer casing is too long or
too short.
• If you hear abnormal noise as a result of looseness in a pulley, you should replace the
pulley.
• If the wheel becomes stiff and difficult to turn, you should lubricate it with grease.
• Do not apply any lubricant to the inside of the hub, otherwise the grease will come out.
• You should periodically wash the sprockets in a neutral detergent and then lubricate them
again. In addition, cleaning the chain with neutral detergent and lubricating it can be a
effective way of extending the useful life of the sprockets and the chain.
t
• If the chain keeps coming off the sprockets during use, replace the sprockets and the
chain.
• Use an outer casing which still has some length to spare even when the handlebars are
turned all the way to both sides. Furthermore, check that the shifting lever does not touch
the bicycle frame when the handlebars are turned all the way.
• Because the high cable resistance of a frame with internal cable routing would impair the
SIS function, this type of frame should not be used.
• Operation of the levers related to gear shifting should be made only when the front
chainwheel is turning.
• For smooth operation, use the specified outer casing and bottom bracket cable guide.
• To ensure the best performance, be sure to use only the specified type of chain. The
wide type chain cannot be used.
• The ID-C050 gear indicator, SC-C050 speedmeter, SC-C051 odometer and SC-C052 clock
and stopwatch are available as separate items. Please ask your bicycle dealer for further
details.
• For maximum performance we highly recommend Shimano lubricants and maintenance
products.
• Parts are not guaranteed against natural wear or deterioration resulting from normal use.
• For any questions regarding methods of installation, adjustment, maintenance or operation,
please contact a professional bicycle dealer.
In order to realize the best performance, we recommend that the following combination be used.
MEGARANGE
Tourney
Series
Gears
Tourney
Tourney
21- gears
18 - gears
21- gears
18 - gears
15 - gears
Right
SL-RS41-7/RS41A-7
SL-RS31-7
SL-RS41-6
SL-RS31-6
SL-RS41-7/RS41A-7
SL-RS31-7
SL-RS41-6
SL-RS31-6
SL-RS31-5
Left
SL-RS41-L/RS41A-L
SL-RS31-LA
SL-RS41-L
SL-RS31-LA
SL-RS31-L
SL-RS31-L
SL-RS31-L
SIS40
SIS40
SIS40
SIS40
SIS40
Shifting lever
Outer casing
Front derailleur
FD-C051 / FD-TY32-A / FD-TY30
FD-C050 / FD-TY10
FD-C051/FD-TY22-GS/FD-TY18/FD-TZ31
FD-C050/FD-TZ30
FD-TY15-GS
Front chainwheel
FC-TX70 / FC-TX71
FC-C051 / FC-TY33-A / FC-TY33
FC-C050 / FC-TY40 / FC-TS32
FC-TX70 / FC-TX71
FC-C051 / FC-TY33-A / FC-TY33
FC-C050 / FC-TY40 / FC-TS32
FC-TY33
RD-TX70 / RD-TX50 / RD-TX30
RD-TX70 / RD-TX50 / RD-TX30
RD-TY15-GS
Rear derailleur
Bottom bracket
BB-UN25
BB-UN25
BB-UN25
BB-UN25
BB-UN25
MF-HG37/TZ07
MF-HG22 / TZ06
MF-Z015
Multiple freewheel
MF-TZ37/ZH37/HG50 MF-HG40-6/HG22/ZH36
Chain
CN-UG51 / HG50 CN-UG51 / HG50 CN-UG51 / HG50 CN-UG51 / HG50 CN-UG51 / HP20
Bottom bracket cable guide
SM-SP18 / BT18
SM-SP18 / BT18
SM-SP18 / BT18
SM-SP18 / BT18
SM-SP18 / BT18
Specifications
Shifting lever
Model number
SL-RS41-7/RS41A-7
SL-RS41-6
SL-RS31-6
SL-RS31-5
SL-RS41-L/RS41A-L
SL-RS31-L
SIS 7-gears
SIS 6-gears
SIS 6-gears
SIS 5-gears
SIS 3-gears
Non SIS
Gears
Front Derailleur
FD-C051/ C050 FD-TY32/TY32-A FD-TY30 FD-TY22-GS FD-TY18 FD-TY15-GS FD-TY10 FD-TZ31/ TZ30
Model number
Front derailleur installation band
diameter (Normal type)
S, M, L
S, M
Front derailleur installation band
diameter (Top route type)
S, M, L
S, M
66°- 69°
Chainstay angle (a)
S, M
S, M
S, M
S, M
66°- 69°
66°- 69°
S
66°- 69°
63°- 66°
66°- 69°
S, M
66°- 69°
S, M
S, M
S, M
S, M
66°- 69°
66°- 69°
Chainstay angle
Front chainwheel
FC-TX71/ C051 FC-TY33/ TY33-A FC-TX70 / C050
Model number
Front chainwheel tooth combination
FC-TY40
48T-38T-28T
42T-34T-24T
Crank arm length
160mm,170mm
Pedal thread dimensions
BC 9/16" X 20 T.P.I. (English thread)
Bottom bracket cup thread dimensions
170mm
160mm,170mm 160mm,170mm
FD-C051
FD-TY33
170mm
BC 9/16" X 20 T.P.I. (English thread)
BC 1.37" X 24 T.P.I. (68, 73 mm)
Applicable front derailleur
FC-TS32
BC 1.37" X 24 T.P.I. (68, 73 mm)
FD-C050
FD-C050 / TZ30 FD-C050 / TZ30
Bottom Bracket
Type
Chain line
Spindle length
Shell width
Stamped marking
Thread dimensions
Triple
47.5mm
122.5mm
68mm
D-NL
BC1.37 X 24 T.P.I.
* FC-TY40 : 47.5mm ––– YL117
Rear derailleur
Model number
RD-TX70
RD-TX50
RD-TX30
MGS
MGS
MGS
GS
7-gears/6-gears
7-gears/6-gears
7-gears/6-gears
5-gears
Type
Gears
Total capacity
RD-TY15-GS
43T
43T
43T
34T
28 - 34T
28 - 34T
28 - 34T
28T
Rear smallest sprocket
11T
11T
11T
14T
Front chainwheel tooth difference
20T
20T
20T
20T
Rear largest sprocket
Sprocket tooth configurations
7-gears
6-gears
5-gears
14, 16, 18, 20, 22, 24, 34T
14, 16, 18, 20, 22, 24, 28T
13, 15, 17, 19, 21, 24, 34T
14, 16, 18, 21, 24, 34T
14, 16, 18, 21, 24, 28T
14, 17, 20, 24, 28T
Gears
Tooth combination
Mounting the shifting lever
Leave a gap of 0.5 mm between the Revo-shift
lever and the half grip.
Half grip
Half grip
Handlebar
Handlebar
3 mm Allen Key
[SL-RS41]
[SL-RS31]
Tightening torque:
2 N·m {18 in. lbs.}
Install the brake lever in a position
where it will not obstruct brake
operation. Do not use in a
combination which causes brake
operation to be obstructed.
Gear shifting operation
Pedaling becomes
heavier
Pedaling becomes
lighter
Pedaling becomes
lighter
Pedaling becomes
heavier
Installation of the bottom bracket
Install using the special tool TL-UN74.
First install the main body, then the adapter.
Front Chainwheel
Tightening torque:
50 - 70 N·m {435 - 608 in. lbs.}
Adapter
Bottom Bracket
Installation of the front chainwheel
Use the cotterless crank extractor (TL-FC10) to
install the front chainwheel.
S
G
NA
n
F
C or
h
a
i
OW
y
RRn l
o
Tightening torque:
35 - 50 N·m {305 - 435 in. lbs.}
MA
SH
SHI
NO
I MA
NO
SG
SG
E
-3
0
E-
40
Securely tighten
Installation of the front derailleur
1. < FD-C051 / FD-C050 / FD-TY32 / FD-TY32-A / FD-TY30 / FD-TY22 /
FD-TY10 >
Adjust and then install the front derailleur as shown in the illustration. Do not
remove the Pro-Set alignment block at this time.
Gear teeth should
come within this
range
1 - 3 mm
Pro-Set gauge
Pro-Set alignment block
3 mm
5 mm
< FD-TY18 / FD-TY15 / FD-TZ31 /
FD-TZ30 >
Install so that there is 1 -3 mm of
clearance at the closest point between
the largest chainring and the bottom
edge of the chain guide.
1 - 3 mm
2. The level section of the chain guide outer plate should be
directly above and parallel to the largest chainring.
Chainwheel
(largest chainring)
3. Secure using a 9 mm spanner (TY30, TY18, TY15, TY10,
TZ31, TZ30) or a 5 mm Allen key (C051, C050, TY32,
TY32-A, TY22).
Chain guide
Tightening torque:
5 - 7 N·m {44 - 60 in. lbs.}
Installation of the rear derailleur
Direct-mount type
Tightening torque:
8 - 10 N·m
{70 - 86 in. lbs.}
5 mm Allen Key
Push in and
tighten
Frame
Bracket type
Bracket nut
Tightening torque:
3 - 4 N·m
{26 - 34 in. lbs.}
Bracket bolt
Bracket
Installation of the freewheel
Tightening torque:
30 N·m {260 in. lbs.}
To install
Freewheel removal tool
To disassemble
TL-FW30
Chain length
Add 2 links (with the chain on both the
largest sprocket and the largest chainring)
Largest
sprocket
Chain
Large
chainring
Adjustment
Be sure to follow the sequence described below.
1. Low adjustment
< FD-C051 / FD-C050 / FD-TY32 / FD-TY32-A / FD-TY30 / FD-TY22 /
FD-TY10 >
First remove the Pro-Set alignment block. Next,
FD-C051 / C050 / TY32 /
set so that the clearance between the chain guide
TY32-A / TY22
inner plate and the chain is 0 - 0.5 mm.
FD-TY30 / TY10
Pro-Set alignment block
Low
adjustment
screw
Chain position
Largest
sprocket
Smallest
chainring
Chain guide inner
plate
Chain
< FD-TY18 / FD-TY15 / FD-TZ31 / FD-TZ30 >
Set so that the clearance between the
chain guide inner plate and the chain is
0 - 0.5mm.
FD-TY18 / TY15 /
TZ31 / TZ30
Low
adjustment
screw
Chain position
Largest
sprocket
Smallest
chainring
Chain guide inner
plate
Chain
2. Connection and securing of cable
While firmly pulling the cable, tighten the fixing bolt with a 9 mm spanner
(TY30, TY18, TY15, TY10, TZ31, TZ30) or a 5 mm Allen key (C051, C050,
TY32, TY32-A, TY22) to secure the cable.
Tightening torque: 5 - 7 N·m {44 - 60 in. lbs.}
3. Adjustment of cable tension
After taking up the initial slack in the cable, re-secure to the front derailleur as
shown in the illustration.
Normal type
Pull
Top route type
Pull
Cut off the excess length of inner cable and then install the inner end cap.
< FD-C051 / FD-C050 >
Note:
Pass the cable through
as shown in the
illustration.
5 mm allen key
Top route type
Wire fixing bolt
Normal type
FD-TY30 / TY18 / TY15 /
TY10 / TZ31 / TZ30
4. Top adjustment
Top adjustment
screw
Set so that the clearance between
the chain guide outer plate and the
chain is 0 - 0.5 mm.
Chain guide
outer plate
Chain position
Smallest
sprocket
Largest
chainring
FD-C051 / C050 /
TY32 / TY32-A /
TY22
Chain
5. Adjustment of the intermediate chainring (SL-RS41-L)
Set the chain onto the largest sprocket, and at the front, move the chain from
the largest chainring to the intermediate chainring. Adjust using the cable
adjusting bolt so that the clearance between the chain guide inner plate and
the chain is 0 - 0.5 mm.
Outer casing adjustment barrel
Chain position
Largest
sprocket
Intermediate
chainring
Chain guide
inner plate
Chain
6. Troubleshooting chart
After completion of steps 1 - 5, move the shifting lever to check the
shifting. (This also applies if shifting becomes difficult during use.)
If the chain falls to the crank side
Tighten the top adjustment screw
clockwise (about 1/4 turn).
If shifting is difficult from the
intermediate chainring to the largest
chainring
Loosen the top adjustment screw
counterclockwise (about 1/8 turn).
If shifting is difficult from the
intermediate chainring to the
smallest chainring
Loosen the low adjustment screw
counterclockwise (about 1/4 turn).
If there is interference between the
chain and the front derailleur inner
plate at the largest chainring
Tighten the top adjustment screw
clockwise (about 1/8 turn).
If there is interference between the
chain and the front derailleur outer
plate at the largest chainring
Loosen the top adjustment screw
counterclockwise (about 1/8 turn).
If the intermediate chainring is
skipped when shifting from the
largest chainring
Loosen the outer casing adjustment
barrel counterclockwise (1 or 2 turns).
*
Tighten the outer casing adjustment
barrel clockwise (1 or 2 turns).
*
If there is interference between the
chain and front derailleur inner plate
when the rear sprocket is shifted to
the largest sprocket when the
chainwheel is at the intermediate
chainring position.
If shifting is difficult from the largest
chainring to the intermediate
chainring
If the chain falls to the bottom
bracket side
* SL-RS41-L
Tighten the low adjustment screw
clockwise (about 1/2 turn).
Cable securing and stroke adjustment
< RD-TX70 / RD-TX50 >
Place the outer casing so that it does not touch the basket and
mudguard, otherwise it may cause a problem with the performance of
the derailleur.
Set the outer casing (RD-TX70/RD-TX50) so that its length is as
follows.
• If routing the casing upward:
(The chain should be on the largest chainring and on
the largest sprocket.)
Add 10 mm to the length of the outer casing from the
end that is inserted into the outer casing holder to the
end which is inserted into the link.
max.
Outer casing
holder
angle
L
Chain position
Largest
sprocket
Largest
chainring
Link
• If routing the casing downward:
(The chain should be on the largest chainring and on the largest
sprocket.)
Set the length of the outer casing so that it describes a smooth arc,
and so that the link stops in a position where there is a small gap
between the link and the link stop.
max.
angle
Link
Chain position
Largest
sprocket
Largest
chainring
Link stop
Connect the inner cable to the
derailleur as shown in the illustration.
Inner cable
1. Top adjustment
Turn the top adjustment screw to adjust so that the guide pulley is
below the outer line of the smallest sprocket when looking from the
rear.
Outer line of smallest
sprocket
1
2
1
2
Top
adjustment
screw
Guide pulley
RD-TY15
RD-TX70 / TX50 / TX30
2. Connection and securing of cable
Connect the cable to the rear derailleur and, after taking up the initial
slack in the cable, reattach to the rear derailleur as shown in the
illustration.
Secure the cable by pulling it with pliers with a force of 5 - 10 kg.
Tightening torque:
5 - 7 N·m {44 - 60 in. lbs.}
Note: Be sure that the cable is
securely in the groove.
Pull
Groove
3. Low adjustment
Turn the low adjustment screw so that the guide pulley moves to a
position directly below the largest sprocket.
Largest
sprocket
Guide pulley
1
2
2
Low adjustment
screw
RD-TY15
1
RD-TX70 / TX50 / TX30
4. How to use the B-tension adjustment screw
< RD-TX70 / RD-TX50 / RD-TX30 >
Mount the chain on the smallest chainring and the largest sprocket,
and turn the crank arm backward. Then turn the B-tension adjustment
screw to adjust the guide pulley as close to the sprocket as possible but
not so close that it touches.
Next, set the chain to the
Largest sprocket
Smallest sprocket
smallest sprocket and repeat
2
the above to make sure that the
2
pulley does not touch the
sprocket.
1
1
1
2
B-tension
adjustment screw
SIS Adjustment
Operate the shifting lever several times to move
the chain to the 2nd sprocket. Then, while
pressing the lever just enough to take up the play
in the lever, turn the crank arm.
Play
When shifting to 3rd
When no sound at
all is heard
adjustment
ballel
adjustment
ballel
RD-TX70
RD-TX50
RD-TX70
RD-TX50
RD-TX30
Tighten the outer cable adjusting
barrel until the chain returns to
the 2nd sprocket. (clockwise)
RD-TX30
Loosen the outer casing
adjustment barrel until the chain
touches the 3rd sprocket and
makes noise. (counter clockwise)
Best setting
The best setting is when the shifting lever is operated
just enough to take up the play and the chain touches
the 3rd sprocket and makes noise.
* Return the lever to its original position (the position
where the lever is at the 2nd sprocket setting and it has
been released) and then turn the crank arm clockwise.
If the chain is touching the 3rd sprocket and making
noise, turn the outer casing adjustment barrel
clockwise slightly to tighten it until the noise stops and
the chain runs smoothly.
For the best SIS performance, periodically lubricate all power-transmission
parts.
Replacing the inner cable
Replace the inner cable by carrying out
steps ➀ to ➂ as shown in the illustrations.
➀
➁
➂
Installation of the switch
Remove the switch cap and install
the switch as shown in the
illustration.
Switch
Switch cap
This service instruction explains how to use
and maintain the Shimano bicycle parts
which have been used on your new bicycle.
For any questions regarding your bicycle or
other matters which are not related to
Shimano parts, please contact the place of
purchase or the bicycle manufacturer.
One Holland, Irvine, California 92618, U.S.A. Phone: +1-949-951-5003
Industrieweg 24, 8071 CT Nunspeet, The Netherlands Phone: +31-341-272222
3-77 Oimatsu-cho, Sakai, Osaka 590-8577, Japan
Please note: specifications are subject to change for improvement without notice. (English)
© Apr. 2003 by Shimano Inc. XBC SZK Printed in Singapore
t
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement