IC693APU302
This Datasheet for the
IC693APU302
Axis Positioning Module (APM), 2 Axis
http://www.cimtecautomation.com/parts/p-14580-ic693apu302.aspx
Provides the wiring diagrams and installation guidelines for this GE Series 90-30
module.
For further information, please contact Cimtec Technical Support at
1-866-599-6507
[email protected]
8
IC693APU301/302 Motion Mate Axis Positioning Module (APM)
The Motion Mate APM is an easy-to-use intelligent, fully programmable one-axis (IC693APU301)
or two-axis (IC693APU302) motion control module for the Series 90-30 PLC. The APM allows a
PLC user to combine high-performance control with PLC logic solving functions in one integrated
system. The APM can be configured to operate in either Standard mode or Follower mode. When
used in Standard mode, it combines high-performance motion control with PLC logic solving
functions in one integrated system. When used in Follower mode, it provides high-performance
“electronic gearing” for continuous master/slave applications. The desired mode is easily selected
by configuring a setup parameter in the configuration software.
EN1
STAT
EN2
OK
AXIS POS
MODULE
CFG
ONE
AXIS
C
O
M
M
B
A
Figure 8-10. Motion Mate APM Module
The Series 90-30 and APM operate together as one integrated motion control package. The APM
controls axis motion and handles all direct communications to the drive and machine while the
PLC automatically transfers data between PLC tables and the APM.
The PLC also provides a means for connecting Operator Interfaces, which can control and monitor
system operation. An example of an APM servo system showing the hardware and software used
to configure, program, and operate the system is shown below.
The APM can be installed in any Series 90-30 CPU, expansion, or remote baseplate. For
embedded CPUs (311, 313, or 323), you may have up to three APM modules. For a modular CPU
(331 or higher), you may have up to eight APM modules in one system, with a maximum of three
APM modules per baseplate.
Multiple motion programs may be created and stored in the APM (maximum of 10 may be stored
in the APM) with the Motion Programmer software package. The APM is configured and
programmed with VersaPro software (Version 1.1 or later) or Logic Developer-PLC.
GFK-0356Q
Chapter 8 Option Modules
8-15
8
The APM faceplate (front panel) has two 24-pin high-density connectors for servo connections.
The connector labeled A contains connections for Axis 1. Connector B, for a 1-axis APM, contains
general purpose connections. Connector B, for a 2-axis APM, has connections for Axis 2 as well
general purpose connections. To make wiring easier to the drive and machine, each high-density
connector is typically connected by a short cable to a terminal block.
CPU
MACHINE 1
APM
DRIVE
ENCODER 1
MACHINE 2
DRIVE
Configuration Software
Motion Programming
Software
ENCODER 2
Figure 8-11. Example of Motion Mate APM Servo System
APM Cables
These cables consists of a 24-pin I/O connector , a cable, and a 25-pin D-type terminal block
connector. (Cables are documented in Chapter 10.) Available cables are:
„
IC693CBL311 (10 feet/3 meters)
„
IC693CBL319 (3 feet/1 meter)
„
IC693CBL317 (10 feet/3 meters) with an 8” external shield pigtail
„
C693CBL320 (3 feet/1 meter) with an 8” external shield pigtail
For building custom-length cables, the 24-pin I/O cable connector is available in three different kits
(solder eyelet receptacle, crimp wire receptacle, and IDC (ribbon) receptacle). The terminal block
is Weidmuller RD25 910648 or equivalent (must be compatible with the I/O cable
IC693CBL311/319/317/320 - see Chapter 10 for details).
Motion Mate APM Module Documentation
See the following manuals for detailed information on Power Mate APM Modules:
„
GFK-0840
Motion Mate APM for Series 90-30 PLC Standard Mode User’s Manual
„
GFK-0781
Motion Mate APM for Series 90-30 PLC Follower Mode User’s Manual
„
GFK-0664
Series 90 PLC APM Programmer’s Manual
Related servo manual:
„
8-16
GFK-1581
SL Series Servo User’s Manual
Series 90-30 PLC Installation and Hardware Manual – August 2002
GFK-0356Q
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement