Ultrastar 15K147 Quick Installation Guide v1.0

Ultrastar 15K147 Quick Installation Guide v1.0
Quick Installation Guide
Hitachi Ultrastar 15K147
Models:
HUS151414VL3600
HUS151473VL3600
HUS151436VL3600
HUS151414VL3800
HUS151473VL3800
HUS151436VL3800
HANDLING PRECAUTIONS
•
•
•
•
•
•
Do not open the electrostatic discharge (ESD) bag containing the drive until required.
Do not apply pressure on the drive during handling and installation.
To prevent damage from impact or vibration always set the drive down gently.
Handle the drive carefully by the edges. Do not touch the exposed printed circuit board or any electronic
components.
Do not cover the breather hole! Covering the breather hole may result in loss of data.
Save the packaging materials including the ESD bag in the event that the drive must be returned.
INSTALLING THE DRIVE
1.
2.
3.
Record the serial number and part number of your hard drive for future reference.
Turn off the computer and remove the computer system cover.
Before handling the hard disk drive, discharge any static electricity from yourself and your clothing. With
one hand touch an unpainted metal surface on the computer chassis, and then touch the ESD bag with the
other hand for a minimum of two seconds.
4. Remove the hard drive from the ESD bag.
5. Unplug the computer.
6. For the 68-pin model assign a SCSI ID address if necessary. The default ID is 6.
Page 1
version 1.0
ADDRESS JUMPER AND DRIVE OPTION BLOCKS
THE 68PIN J4 OPTIONS (from left to right)
Pin
1
3
Signal
Name
+5V 150
ohm
+5V Pdyswitch
Pin
Signal
Name
2
LEDout
4
5
GND
6
7
9
11
13
GND
GND
GND
GND
8
10
12
14
Enable
Term Power
Force SE
mode
ID0
ID1
ID2
ID3
JUMPERS ARE NOT REQUIRED ON THE 80 PIN CONNECTOR.
Page 2
version 1.0
Auxiliary Connector J6
7.
Mounting Orientation
The drive may be installed horizontally or Vertically. Provide adequate airflow to cool drive. Use 4
Mounting screws(6x32UNC). Maximum screw penetration 3.8mm(0.15 in) into drive.
8.
For a 68-pin drive attach the power cable and ensure that one end of the SCSI cable
is connected to the host adapter. The cable should be terminated. (The 80-pin drive is plugged
into the server backplanes and requires no cables)
9.
Ensure that all cables are connected and properly routed.
10. Turn on your computer.
•
•
•
Page 3
If the system boots be sure the drive is recognized. If it is turn off the computer and replace the cover.
Proceed to install your operating system.
If your system does not boot up, turn off your computer and check all connections and settings. Turn
on and boot the system.
If the system fails to boot, turn off your system. Contact the Hitachi GST Technical Support Center for
assistance – www.hitachigst.com
version 1.0
Special Notes:
•
For this drive to operate in LVD mode all SCSI devices including the SCSI bus host adapter must be
LVD devices.
•
The drive is designed to detect if the SCSI bus is LVD or SE. The drive will function based upon the
mode that it detects. To force SE ended mode on the 68-pin drive, place a jumper across pins 5 & 6
connector J4.
•
For 68 pin drives termination power must be provided. In most cases the host adapter provides it. For
the drive to provide Term power install a jumper on pins 3 & 4 on option jumper J4. (The 80-pin drive does
not provide termination power.)
Page 4
version 1.0
© Copyright Hitachi Global Storage Technologies 2004
Hitachi Global Storage Technologies
5600 Cottle Road
San Jose, CA 95193
Produced in the United States 11/04
All rights reserved
Ultrastar™ is a trademark of Hitachi Global
Storage Technologies.
Other product names are trademarks or registered
trademarks of other respective companies.
References in this publication to Hitachi Global
Storage Technologies products, programs or
services do not imply that Hitachi Global Storage
Technologies intends to make these available in all
countries in which Hitachi Global Storage
Technologies operates.
Product information is provided for information
purposes only and does not constitute a warranty.
Information is true as of the date of publication and
is subject to change. Actual results may vary.
This publication is for general guidance only.
Photographs may show design models.
November 8, 2004
Page 5
version 1.0
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement