05_TSX_CigLighter
INSTALLATION
INSTRUCTIONS
Accessory
Application
CIGARETTE LIGHTER
WITH ASHTRAY
08U25-SEC-210
2005 TSX
PARTS LIST
Publications No.
BII 28357
Issue Date
OCT 2004
3.
Remove the trim ring.
M/T Model:
•
Ashtray
Remove the shift knob by turning it
counterclockwise, and remove the nut.
SHIFT KNOB
(Counterclockwise.)
Cigarette lighter harness
NUT
2031021S
11 Wire ties
TOOLS REQUIRED
Phillips screwdriver
10 mm Combination wrench
•
Gently pry up on the trim ring to release the
eight clips.
•
Unplug the two seat heater connectors (if
equipped), and remove the trim ring.
CLIPS (8)
TRIM RING
INSTALLATION
Customer Information: The information in this
installation instruction is intended for use only by
skilled technicians who have the proper tools,
equipment, and training to correctly and safely add
equipment to your vehicle. These procedures
should not be attempted by “do-it-yourselfers.”
1.
Make sure you have the anti-theft code for the
radio and, if equipped, the navigation system, then
write down the frequencies for the preset buttons.
2.
Disconnect the negative cable from the battery.
SEAT HEATER
CONNECTOR
(if equipped)
© 2004 American Honda Motor Co., Inc - All Rights Reserved.
BII 28357 (0410)
08U25-SEC-2000-91
2031030S
1 of 5
A/T Model:
5.
•
Gently pry up on the trim ring to release the
eight clips.
•
Unplug the two seat heater connectors (if
equipped), and remove the trim ring.
Remove the four self-tapping screws. Gently pull
out on the coin pocket holder, unplug the vehicle
connector and vehicle clip, and remove the coin
pocket holder.
SELF-TAPPING
SCREW (reuse.)
CLIPS (8)
TRIM RING
CLIP
COIN POCKET
HOLDER
(Not reused.)
VEHICLE
CONNECTOR
2031040S
SEAT HEATER
CONNECTOR
(if equipped)
2N03011S
4.
Open the pocket lid. Pull the pocket out toward
you to release the four clips, unplug the
illumination bulb, unclip the illumination bulb
harness from the pocket, and remove the pocket.
Take care not to damage the illumination bulb.
6.
Remove the driver's dashboard lower cover (one
self-tapping screw and three retaining clips).
RETAINING
CLIPS (3)
ILLUMINATION
BULB
CLIP
SELF-TAPPING
SCREW
LID
POCKET
2N01080Y
DRIVER’S
DASHBOARD
LOWER COVER
CLIPS (4)
2031052S
2 of 5
BII 28357 (0410)
© 2004 American Honda Motor Co., Inc - All Rights Reserved.
7.
Remove the driver’s dashboard under cover (three
clips, one pin and one holder).
CLIPS (3)
10. Route the cigarette lighter 5-pin connector to the
switch panel opening, and plug the cigarette
lighter harness 5-pin connector into the vehicle
5-pin connector you just unplugged (second
connector from the left) as shown.
CIGARETTE LIGHTER HARNESS
5-PIN CONNECTOR
VEHICLE
5-PIN CONNECTOR
HOLDER
2N19010S
DRIVER’S
DASHBOARD
UNDER COVER
8.
PIN
Release the two clips and two hooks, and remove
the switch panel by pulling it out toward you.
3513011M
11. Route the other end of the cigarette lighter
harness along the vehicle harness, and secure it
to the vehicle harness with two wire ties in the
areas shown.
VEHICLE
CONNECTOR
SWITCH
PANEL
CIGARETTE
LIGHTER
HARNESS
WIRE TIE
VEHICLE
HARNESS
HOOKS (2)
RETAINING
CLIPS (2)
2N03021S
9.
Unplug the vehicle connectors from the switch
panel, then remove the switch panel.
© 2004 American Honda Motor Co., Inc - All Rights Reserved.
2N03041S
BII 28357 (0410)
3 of 5
12. Plug the cigarette lighter 5-pin connector into the
VSA switch, and reinstall the switch panel.
14. Continue routing the cigarette lighter harness to
the center console opening, and secure it to the
vehicle harness with the five wire ties.
CIGARETTE LIGHTER HARNESS
5-PIN CONNECTOR
WIRE TIE
VSA
SWITCH
SWITCH
PANEL
3513031M
13. Route the cigarette lighter harness in front of the
steering shaft. Secure the cigarette lighter harness
to the vehicle harness with four wire ties.
CIGARETTE
LIGHTER
HARNESS
VEHICLE
HARNESS
2N03060S
15. Remove the bulb cap from the bulb on the
cigarette lighter harness.
WIRE TIE
ASHTRAY
BULB
WIRE
TIE
BULB
BULB CAP
VEHICLE
HARNESS
4 of 5
STEERING
SHAFT
CIGARETTE
LIGHTER
HARNESS
CIGARETTE
LIGHTER
HARNESS
2N03070S
3513021M
BII 28357 (0410)
© 2004 American Honda Motor Co., Inc - All Rights Reserved.
16. Push and turn the bulb on the cigarette lighter
harness into the hole in the ashtray.
SELF-TAPPING
SCREW (Reuse.)
CIGARETTE
LIGHTER
HARNESS
2-PIN
CONNECTOR
ASHTRAY
VEHICLE
CONNECTOR
2N03080S
17. Plug the cigarette lighter harness 2-pin connector
and vehicle connectors unplugged in step 7 into
the ashtray, and install the ashtray (two selftapping screws).
18. Check that all wire harnesses are routed properly
and all connectors are plugged in.
19. Reinstall all removed parts. Check that all clips
and fasteners are installed securely.
20. Reconnect the negative cable to the battery.
21. Reset the clock, and reset the radio station
presets.
22. Test the operation of the cigarette lighter.
NOTE: Whenever the battery is disconnected, the
driver’s window AUTO function is disabled.
23. Start the engine. Push down on the driver’s
window switch until the window is fully open.
24. Pull up on the driver’s window switch to close
the window completely, then hold the switch for
2 seconds or more.
25. Test the window AUTO function.
© 2004 American Honda Motor Co., Inc - All Rights Reserved.
BII 28357 (0410)
5 of 5
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement