Advantech | TPC-1250H | User manual | Advantech TPC-1250H User manual

User Manual
TPC-1250H/1550H/
1750H
Industrial Touch Panel
Computers with Intel® Atom™
Processors
Copyright
The documentation and the software included with this product are copyrighted 2012
by Advantech Co., Ltd. All rights are reserved. Advantech Co., Ltd. reserves the right
to make improvements in the products described in this manual at any time without
notice. No part of this manual may be reproduced, copied, translated or transmitted
in any form or by any means without the prior written permission of Advantech Co.,
Ltd. Information provided in this manual is intended to be accurate and reliable. However, Advantech Co., Ltd. assumes no responsibility for its use, nor for any infringements of the rights of third parties, which may result from its use.
Acknowledgements
Intel and Pentium are trademarks of Intel Corporation.
Microsoft Windows and MS-DOS are registered trademarks of Microsoft Corp.
All other product names or trademarks are properties of their respective owners.
This Manual Covers the Following Models:
 TPC-1250H
 TPC-1550H
 TPC-1750H
Part No. 2003155010
Edition 1
Printed in Taiwan
June 2012
TPC-1250H/1550H/1750H User Manual
ii
Product Warranty (2 years)
Advantech warrants to you, the original purchaser, that each of its products will be
free from defects in materials and workmanship for two years from the date of purchase.
This warranty does not apply to any products which have been repaired or altered by
persons other than repair personnel authorized by Advantech, or which have been
subject to misuse, abuse, accident or improper installation. Advantech assumes no
liability under the terms of this warranty as a consequence of such events.
Because of Advantech’s high quality-control standards and rigorous testing, most of
our customers never need to use our repair service. If an Advantech product is defective, it will be repaired or replaced at no charge during the warranty period. For outof-warranty repairs, you will be billed according to the cost of replacement materials,
service time and freight. Please consult your dealer for more details.
If you think you have a defective product, follow these steps:
1. Collect all the information about the problem encountered. (For example, CPU
speed, Advantech products used, other hardware and software used, etc.) Note
anything abnormal and list any onscreen messages you get when the problem
occurs.
2. Call your dealer and describe the problem. Please have your manual, product,
and any helpful information readily available.
3. If your product is diagnosed as defective, obtain an RMA (return merchandize
authorization) number from your dealer. This allows us to process your return
more quickly.
4. Carefully pack the defective product, a fully-completed Repair and Replacement
Order Card and a photocopy proof of purchase date (such as your sales receipt)
in a shippable container. A product returned without proof of the purchase date
is not eligible for warranty service.
5. Write the RMA number visibly on the outside of the package and ship it prepaid
to your dealer.
iii
TPC-1250H/1550H/1750H User Manual
Declaration of Conformity
CE
This product has passed the CE test for environmental specifications when shielded
cables are used for external wiring. We recommend the use of shielded cables. This
kind of cable is available from Advantech. Please contact your local supplier for
ordering information.
FCC Class A
Note: This equipment has been tested and found to comply with the limits for a Class
A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in
which case the user will be required to correct the interference at his own expense.
Technical Support and Assistance
1.
2.
Visit the Advantech web site at http://support.advantech.com where you can find
the latest information about the product.
Contact your distributor, sales representative, or Advantech's customer service
center for technical support if you need additional assistance. Please have the
following information ready before you call:
– Product name and serial number
– Description of your peripheral attachments
– Description of your software (operating system, version, application software,
etc.)
– A complete description of the problem
– The exact wording of any error messages
TPC-1250H/1550H/1750H User Manual
iv
Safety Instructions
1.
2.
3.
Read these safety instructions carefully.
Keep this User Manual for later reference.
Disconnect this equipment from any AC outlet before cleaning. Use a damp
cloth. Do not use liquid or spray detergents for cleaning.
4. For plug-in equipment, the power outlet socket must be located near the equipment and must be easily accessible.
5. Keep this equipment away from humidity.
6. Put this equipment on a reliable surface during installation. Dropping it or letting
it fall may cause damage.
7. The openings on the enclosure are for air convection. Protect the equipment
from overheating. DO NOT COVER THE OPENINGS.
8. Make sure the voltage of the power source is correct before connecting the
equipment to the power outlet.
9. Position the power cord so that people cannot step on it. Do not place anything
over the power cord.
10. All cautions and warnings on the equipment should be noted.
11. If the equipment is not used for a long time, disconnect it from the power source
to avoid damage by transient overvoltage.
12. Never pour any liquid into an opening. This may cause fire or electrical shock.
13. Never open the equipment. For safety reasons, the equipment should be
opened only by qualified service personnel.
14. If one of the following situations arises, get the equipment checked by service
personnel:
The power cord or plug is damaged.
Liquid has penetrated into the equipment.
The equipment has been exposed to moisture.
The equipment does not work well, or you cannot get it to work according to
the user's manual.
The equipment has been dropped and damaged.
The equipment has obvious signs of breakage.
15. DO NOT LEAVE THIS EQUIPMENT IN AN ENVIRONMENT WHERE THE
STORAGE TEMPERATURE MAY GO BELOW -20° C (-4° F) OR ABOVE 60° C
(140° F). THIS COULD DAMAGE THE EQUIPMENT. THE EQUIPMENT
SHOULD BE IN A CONTROLLED ENVIRONMENT.
16. CAUTION: DANGER OF EXPLOSION IF BATTERY IS INCORRECTLY
REPLACED. REPLACE ONLY WITH THE SAME OR EQUIVALENT TYPE
RECOMMENDED BY THE MANUFACTURER, DISCARD USED BATTERIES
ACCORDING TO THE MANUFACTURER'S INSTRUCTIONS.
The sound pressure level at the operator's position according to IEC 704-1:1982 is
no more than 70 dB (A).
DISCLAIMER: This set of instructions is given according to IEC 704-1. Advantech
disclaims all responsibility for the accuracy of any statements contained herein.
Caution! Danger of explosion if battery is incorrectly replaced. Replace only with
the same or equivalent type recommended by the manufacturer. Dispose of used batteries according to the manufacturer's instructions.
v
TPC-1250H/1550H/1750H User Manual
TPC-1250H/1550H/1750H User Manual
vi
Chapter
1
General Information ............................1
1.1
1.2
Introduction ............................................................................................... 2
Specifications ............................................................................................ 2
1.2.1 System Kernel............................................................................... 2
1.2.2 I/O Ports........................................................................................ 2
1.2.3 Safety and Environment................................................................ 2
LCD Specifications.................................................................................... 3
Touchscreen Specifications ...................................................................... 3
Power ........................................................................................................ 3
I/O Ports Arrangement .............................................................................. 4
Figure 1.1 I/O Port Arrangement ................................................. 4
Panel Mounting ......................................................................................... 4
Figure 1.2 Panel Mounting........................................................... 4
Dimensions and Cutout............................................................................. 5
Figure 1.3 TPC-1250H Dimensions............................................. 5
Figure 1.4 TPC-1550H Dimensions............................................. 6
Figure 1.5 TPC-1750H Dimensions............................................. 7
1.3
1.4
1.5
1.6
1.7
1.8
Chapter
2
System Setup .......................................9
2.1
System Setup.......................................................................................... 10
Figure 2.1 Unpack the Package ................................................ 10
Figure 2.2 Install CompactFlash Memory Card ......................... 11
Figure 2.3 Power Connector and Power Lines .......................... 11
Figure 2.4 Power Receptor & Button Pin Assignment ............... 12
2.1.1 Installing the Drivers ................................................................... 12
3
Features in Windows XP Embedded13
3.1
3.2
3.3
Features in Windows XP Embedded ...................................................... 14
EWF ........................................................................................................ 14
HORM ..................................................................................................... 14
Appendix A
Serial Port Settings ...........................15
A.1
A.2
A.3
Jumper Settings & Connector List........................................................... 16
Pin Assignment ....................................................................................... 16
RS-485 / RS-422 Setting......................................................................... 16
Chapter
vii
TPC-1250H/1550H/1750H User Manual
TPC-1250H/1550H/1750H User Manual
viii
Chapter
1
1
General Information
1.1 Introduction
The TPC-1250H/1550H/1750H Touch Panel Computers are state-of-the-art Human
Machine Interfaces featuring 12"/15”/17” displays with Intel Atom N270 processors
and the following key features:



Fanless
By using a low-power processor, the system does not have to rely on fans,
which often are unreliable and causes dust to circulate inside the equipment.
Multiple OS
In addition to the OS support of Windows XP, Advantech offers platform support
for WES7 and Windows XP embedded. The optional Windows CE operating
system, specifically for Industrial Touch Panel Computers is also available.
Energy Star Approval
1.2 Specifications
1.2.1 System Kernel







CPU: Intel® Atom™ N270 1.6GHz
BIOS: Award 4 Mbit flash BIOS
System Chipset: 945GSE + ICH7M
Memory: 2GB SO-DIMM DDR2 667 SDRAM
VGA: Integrated in 945GSE
Ethernet: 10/100/1000Base-T
Watchdog Timer: W83627DHG watchdog timer; 1.6 second timeout period

Storage: CFast® slot or 2.5" SATA HDD bundled with extension HDD kit(TPC651H-EHKE) x 1
1.2.2 I/O Ports



2 serial ports: RS-232 x 1, RS-232/422/485 x 1
2 RJ-45 Ethernet port
2 USB 2.0 Ports: compliant with USB 1.0 and 1.1. (Host)
1.2.3 Safety and Environment
Safety
 FCC Class A
 CE certificated
 The front bezel is compliant with NEMA 4 and IP65
Environment
 Operating Temperature:
– 0 ~ 45°C (32 ~ 113°F)
 Storage Temperature:
– -20 ~ 60°C (-4 ~ 140°F)
 Humidity: 40°C @ 10~95% relative humidity (non-condensing)
 Vibration: 2 grms (5 ~ 500 Hz) with CF Card, 1 grm with HDD kit
TPC-1250H/1550H/1750H User Manual
2
TPC-1250H/1550H/1750H
TFT LCD
Size (diagonal)
12.1", 15", 17"
Maximum Resolution
800 x 600 (SVGA), 1024 x 768 (XGA), 1280 x 1024 (SXGA)
Maximum Colors
262K
Viewing Angle
160°/140°, 160°/140°, 170°/160°
Luminance (cd / m2)
450, 300, 350
Contrast Ratio
700:1, 700:1, 1000:1
Operating Temperature
-30 ~ 85°C
Backlight
LED
Note!
There might be several bright or dark pixels on the LCD. This phenomenon is normal in today’s LCD manufacturing.
1.4 Touchscreen Specifications






Touch Type: Resistive
Base Glass Construction: Tempered glass
Resolution: 1024 x 1024
Light Transmission: 80% ± 3% (Measured by BYK-Gardner)
Controller: RS-232 Interface
Lifespan: 10 million touches at single point
Note!
Touchscreen ITO maybe crash duo to heavy usage .
1.5 Power

Input Voltage: 18 - 28 VDC, 18 - 32 VDC(TPC-1750H)
Note!

The fuse will become an open circuit if the input level exceeds 29 VDC
Typical: 24 VDC @ 1.54 Amp
3
TPC-1250H/1550H/1750H User Manual
General Information
Display Type
Chapter 1
1.3 LCD Specifications
1.6 I/O Ports Arrangement
The arrangement of the I/O ports is shown in Figure 1.1.
Figure 1.1 I/O Port Arrangement
1.7 Panel Mounting
1.
1.
2.
3.
There is an adhesive waterproof gasket on the AL front bezel. Make sure the
waterproof gasket is in position before installing TPC into the panel opening.
Install the TPC into the panel opening.
Find the eight clamps and eight long screws in the accessory pack. Hook the
clamps to the holes around the four sides of the bezel. Insert the screws into
every clamp and fasten them. These screws will push the mounting panel and
fix the unit.
The suggested mounting panel thickness is less than 6 mm (0.236”).
Figure 1.2 Panel Mounting
TPC-1250H/1550H/1750H User Manual
4
General Information
4
6.50
301.5
54
3.50
170
180
311
247.2
186.3
237
6.50
4

Weight: 2.5 kg (5.51 lb), 3 kg (5.51 lb), 3.5kg (6.43 lb)
Dimensions (W x H x D):
– 1250H: 311 x 237 x 54 mm (12.24" x 9.33" x 2.12")
– 1550H: 383 x 307 x 58.1 mm (15.08" x 12.09" x 2.29")
– 1750H: 413.7 x 347.2 x 63.8 (16.28" x 13.68" x 2.5")
Cutout:
– TPC-1250H: 302.5 x 228.5 mm
– TPC-1550H: 374.5 x 298.5 mm
– TPC-1750H: 399.5 x 333
227.5


Chapter 1
1.8 Dimensions and Cutout
Figure 1.3 TPC-1250H Dimensions
5
TPC-1250H/1550H/1750H User Manual
189.25
373.0
297.0
140
7
4
4.5
58.5
76.4
24.70
236.0
307.0
115
306.1
383.0
115
230.1
7
4
Figure 1.4 TPC-1550H Dimensions
TPC-1250H/1550H/1750H User Manual
6
Chapter 1
333
399.5
General Information
89.2
5.5
63.8
25.5
140
413.7
340
272.5
347.2
Figure 1.5 TPC-1750H Dimensions
7
TPC-1250H/1550H/1750H User Manual
TPC-1250H/1550H/1750H User Manual
8
Chapter
2
System Setup
2
2.1 System Setup
You can easily get TPC started by following the below steps.
1. Unpack the TPC package. Check the packing list at the beginning of this manual
to make sure all items have been included.
Figure 2.1 Unpack the Package
TPC-1250H/1550H/1750H User Manual
10
Install a CompactFlash® card containing Windows CE, Embedded Windows XP
or another operating system.
Warning! It is suggested to turn OFF system power as you plug in or pull out the
memory card, even though the CompactFlash memory is hot swappable.
3.
Connect the power connector to the 24 VDC power lines. The power lines can
either be of some power adapter or in-house power source.
Figure 2.3 Power Connector and Power Lines
11
TPC-1250H/1550H/1750H User Manual
System Setup
Figure 2.2 Install CompactFlash Memory Card
Chapter 2
2.
Figure 2.4 Power Receptor & Button Pin Assignment
4.
5.
6.
Plug the power lines into the system power receptor.
Push the power button to power on the system (figure 2.4).
Calibrate the touchscreen (click “PM” in the bottom corner).
Note!
If you want to install the touchscreen driver & use the touchscreen utility,
please refer the user manual which is "PenMount 6000 InstallationGuide" in the DVD.
2.1.1 Installing the Drivers
After installing your system software, you will be able to set up the Ethernet, VGA,
and touchscreen functions. All drivers are stored in a DVD disc entitled “TPC1250H,TPC-1550H and TPC-1750H which can be found in your accessory box.
The various drivers in the DVD disc have their own text files which help users install
the drivers and understand their functions. These files are a very useful supplement
to the information in this manual.
Note!
The drivers and utilities used for the TPC-1250H, TPC-1550H and TPC1750H panel PCs are subject to change without notice. If in doubt,
check Advantech's website or contact our application engineers for the
latest information regarding drivers and utilities.
TPC-1250H/1550H/1750H User Manual
12
Chapter
3
3
Features in Windows
XP Embedded
3.1 Features in Windows XP Embedded
TPC product supports the embedded Windows platform. This section outlines the
important features (EWF and HORM), that are provided in Windows XP embedded.
3.2 EWF
EWF stands for Enhanced Write Filter. It provides an upper filter in the storage device
driver stack that redirects disk write operations to volatile (RAM) or non-volatile (disk)
storage. EWF protects a volume from write access. The benefits are as the following.
Write-protect one or more partitions on your system.
Enable read-only media, such as DVD or flash, to boot and run.
Prolong the lifespan of write-sensitive storage, such as CompactFlash.
TPC-1250H/1550H/1750H XPE provides EWF RAM-REG mode on system partition.
All write to system partition will be redirected to RAM once this mode is enabled. This
mode is manually enabled by customers after they finish all their changes on system
such as installing their applications or adjusting system setting.
Advantech provides a pair of utilities to operate EWF, OSLock andOSUnLock. Please
refer the training slide in the folder, file name is “Advantech XPe Add-one.pdf”.
3.3 HORM
HORM stands for Hibernate Once Resume Many. In HORM environment, a single
hibernation file is used to boot the system repeatedly. To set a HORM environment,
please follow the steps below.
Please make sure EWF is disabled. You can run OSUnLock to disable EWF.
Enable hibernation support:
Run “power options” in control panel, and then select “Enable Hibernation” in hibernation pane.
Enable EWF:
Run OSLock, and then system reboot automatically.
Open those software that customers want to directly use after system resume from
hibernation.
Hibernate via Advantech HORM utility:
Please Click Start Menu->All Programs->Advantech->AdvWF
HORM environment remains all along unless the following events occur:
Run EWF commit command (ewfmgr c: -commit) and then reboot system.
Select “Discard hibernation file” by clicking F8 when system is starting up.
TPC-1250H/1550H/1750H User Manual
14
Appendix
A
A
Jumper and Dip
Switch setting Pin
Assignment
A.1 Jumper and DIP Switch Settings \
A.1.1 Component Construction
A.1.1.1 EAMB-1120 Top side
A.1.1.2 EAMB-1120 Bottom side
TPC-1250H/1550H/1750H User Manual
16
A.1.2.1 CN18 LCD Power Select
CN18 is used to select LCD power
Description
(1-3) & (2-4)
+5V is used to supply LCD panel
(3-5) & (4-6)
+3.3V is used to supply LCD panel*
*Default setting
A.1.2.2 CN4 CMOS Clear Select
CN4 is used to select CMOS enable/disable
Description
(1-3) & (2-4)
Enable (Clear CMOS)
(3-5) & (4-6)
Disable*
*Default setting
A.1.3 DIP Switches
A.1.3.1 SW3 LCD Controlled Function
SW3 is used to select LCD Controlled Function
SW3
LCD Resolution Select
Description
This switch is used to select LCD Resolution
1280*1024(18bit) PWM 2KHz (TPC-1750)
1024*768(18bit) PWM 2KHz (TPC-1550 B)
Default
800*600 (18 bit) PWM 2KHz (TPC-1250 B)
640*480 (18bit) PWM 2kHz (TPC-650 B)
GPI_LCDSEL0
OFF (Pin 1)
ON (Pin 8)
GPI_LCDSEL1
OFF (Pin 2)
ON (Pin 7)
GPI_LCDSEL2
OFF (Pin 3)
ON (Pin 6)
GPI_LCDSEL3
OFF (Pin 4)
ON (Pin 5)
Default Settings
Connect to GOI pin
640*480 (18bit)
PWM 2kHz
TPC-650
800*600
(18bit)
PWM 2kHz
TPC-1250
1020*768
(18bit)
PWM 2kHz
TPC-1550
1280*1024
(18bit)
PWM 2kHz
TPC-1750
GPI_LCDSEL0
ON
OFF
ON
OFF
GPI_LCDSEL1
ON
ON
OFF
OFF
GPI_LCDSEL2
ON
ON
ON
ON
GPI_LCDSEL3
ON
ON
ON
ON
State
17
TPC-1250H/1550H/1750H User Manual
Appendix A Jumper and Dip Switch setting Pin Assignment
A.1.2 Jumper Settings
A.1.3.2 SW5 LCD Controlled Function
SW5
LCD Controlled Function
Description
This switch is used to select LCD Controlled Function
Default
By LCD Specification
LVDS_V_CFG
Left and Right opposite
OFF (Pin 1)
ON (Pin 8)
LVDS_H_CFG
Up and Down opposite
OFF (Pin 2)
ON (Pin 7)
LVDS_SC_CFG
Scan direction control
OFF (Pin 3)
ON (Pin 6)
LVDS_MODE_CFG
Select 6 or 8 bits LVDS input
OFF (Pin 4)
ON (Pin 5)
1
2
3
4
SW5
ON
8
7
6
5
CHS-04TB(2)
<Characteristic>
TPC-1250
Default
TPC-650
State
Default
LVDS_V_CFG
OFF
OFF
LVDS_H_CFG
OFF
OFF
LVDS_SC_CFG
ON
OFF
LVDS_MODE_CFG
ON
OFF
TPC-1550
Default
TPC-1750
State
Default
LVDS_V_CFG
OFF
OFF
LVDS_H_CFG
OFF
OFF
LVDS_SC_CFG
ON
ON
LVDS_MODE_CFG
OFF
ON
TPC-1250H/1550H/1750H User Manual
State
18
State
SW4
Termination Resistor Select
Description
This switch is used to select Termination Resistor (120 ohm) for
long distance transmission or device matching.
Default
Bit1 off & Bit2 off (ISO_COM2_DATA+ & ISO_COM2_RX-)
ISO_COM2_DATA+
Pin 1
ISO_COM2_RX-
Pin 2
ISO_COM2_R_RX+
Pin 3
ISO_COM2_R_DATA-
Pin 4
Default
1
2
SW 4
ON 4
3
CHS-02TB(20)
19
TPC-1250H/1550H/1750H User Manual
Appendix A Jumper and Dip Switch setting Pin Assignment
A.1.3.3 SW4 Termination Resistor Select
A.1.3.4 SW6 RS232,RS422,RS482 Select\
SW6
Description
Default
RS232,RS422,RS485 Select
The serial port CN13 on the TPC-650 1250 1550 1750 is adjustable. It can be set to RS-232, RS-422 or RS-485. This port is
designed with auto data flow control capability.
off
RS232 Mode
RS485 Mode
RS422 Mode
TPC-1250H/1550H/1750H User Manual
20
1
2
6
3
7
4
8
COM1
5
9
COM2
PIN
RS-232
RS-422 RS-485
1
NDCD
TX-
D-
2
NRX
TX+
D+
3
NTX
RX+
4
NDTR
RX-
5
GND
GND
6
NDSR
7
NRTS
8
NCTS
9
NRI
21
GND
TPC-1250H/1550H/1750H User Manual
Appendix A Jumper and Dip Switch setting Pin Assignment
A.2 Pin Assignment
www.advantech.com
Please verify specifications before quoting. This guide is intended for reference
purposes only.
All product specifications are subject to change without notice.
No part of this publication may be reproduced in any form or by any means,
electronic, photocopying, recording or otherwise, without prior written permission of the publisher.
All brand and product names are trademarks or registered trademarks of their
respective companies.
© Advantech Co., Ltd. 2012
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising