Baumatic | BT06.7ME | User manual | Baumatic BT06.7ME User manual

Baumatic BT06.7ME User manual
BT06.8ME
BT08.8ME
60 cm Integrated
hood
User Manual for your Baumatic
BT06.8ME/BT08.8ME
60 cm Integrated
hood
NOTE: This User Instruction Manual contains important
information, including safety & installation points, which will
enable you to get the most out of your appliance. Please keep it
in a safe place so that it is easily available for future reference; for
you or any person not familiar with the operation of the appliance.
GS 03/01/12
2
Contents Page
Environmental note
4
IMPORTANT SAFETY INFORMATION
5–7
Specifications of your cooker hood
BT06.8ME
BT08.8ME
8–9
8
9
Using your Baumatic cooker hood
Before first use
To use your cooker hood
Turning the cooker hood off
10 – 11
10
10 – 11
11
Cleaning your Baumatic cooker hood
General cleaning
The grease filter
12
12
12
Maintenance
Removing and cleaning the grease filter
Changing a light bulb
Fitting the carbon filters
13
13
15
16
-
Installation
Electrical connection
Before beginning installation
Installing your cooker hood
Fitting the décor door
Connecting to external ducting
Extraction mode or recirculation mode?
Completing the installation
18
18
19
20
23
25
26
26
- 27
– 19
- 20
– 22
- 25
- 26
Troubleshooting
27 – 28
Baumatic consumables
29
Contact details
30
17
14
16
17
- 27
3
ENVIRONMENTAL NOTE
Note: Before discarding an old appliance, switch off and
disconnect it from the power supply. Cut off and render any
plug useless. Cut the cable off directly behind the appliance to
prevent misuse. This should be undertaken by a competent
person.
CONFORMITY TO W.E.E.E. DIRECTIVE
4
IMPORTANT SAFETY INFORMATION
Your safety is of the utmost importance to Baumatic.
Please make sure that you read this instruction booklet
before attempting to install or use the appliance. If
you are unsure of any of the information contained in
this booklet, please contact the Baumatic Customer
Care Department.
IMPORTANT: Any installation work must be
carried out by a qualified electrician or
competent person.
o The hood must be installed in accordance with the installation
instructions and all measurements followed.
o If the cooker hood is installed for use above a gas appliance then
the provision for ventilation must be in accordance with the Gas
Safety Codes of Practice BS.6172, BS.5440 & BS.6891 (Natural
Gas) and BS.5482 (LP Gas) 1994, the Gas Safety (Installation &
Use) Regulations, the Building Regulations issued by the
Department of the Environment, the Building Standards
(Scotland) (Consolidated) Regulations issued by the Scottish
Development Department.
o It is dangerous to alter the specifications or to modify this
product in any way. Do not tamper with or attempt to modify
the appliance in any way.
o When installing the hood, ensure that the following
recommended distances are observed between the highest point
on the hob top (including the burners) and the bottom of the
cooker hood:
¾ Electric cookers:
¾ Gas cookers:
¾ Coal/ oil cookers:
700 mm
700 mm
800 mm
IMPORTANT: DO NOT SET YOUR COOKER HOOD LESS
THAN 700mm ABOVE YOUR COOKER.
o When installed between adjoining wall cabinets, the cabinets
must not overhang the hob.
5
o The edges of the cooker hood are sharp – be mindful of this as
you handle your appliance, especially during installation and
cleaning. DO NOT CLEAN IN BEHIND THE GREASE FILTER!
o If the room where the cooker hood is to be used contains a fuel
burning appliance such as a central heating boiler then its flue
must be of the sealed or balanced flue type.
o If other types of flue or appliances are fitted, ensure that there is
an adequate supply of air in the room.
o When the hood is being used in extraction mode, ensure that the
ducting is fire retardant and that there are no bends greater
than 90 degrees as this will reduce the efficiency of the hood.
o Ensure the ducting for the extractor mode has the same
diameter as the outlet hole all the way through.
o Keep young children from using, playing with
or tampering with the cooker hood. Older
children and infirm persons should be
supervised if they are using the cooker hood.
o Your cooker hood is for domestic use only.
o Please dispose of the packing material carefully – children are
especially vulnerable to it.
o Dirty oil is an even greater fire risk.
o Always put lids on pots and pans when cooking
on a gas cooker.
o The manufacturer refuses to accept any responsibility for
damages arising to the hood or for it catching on fire, from a
failure to observe the fire safety advice contained in these
instructions.
6
o Remember that when in extraction mode, your cooker hood is
removing air from your room. Ensure that proper ventilation
measures are being observed.
o Note that the cooker hood removes odours from your
kitchen, not steam.
o Warning - Always ensure that the cooker
hood has been disconnected from the
power supply before carrying out any work
on the hood, including cleaning and
replacing light bulbs.
o Do not connect the ducting system of this appliance to an
existing ventilation system being used for any other purpose.
o Do not install above a cooker with a high level grill.
o Never leave frying pans unattended during use
as overheated fats and oils might catch fire.
o The cooker hood should not be exposed to a direct heat source
from the cooking device underneath it, i.e. naked flame from a
gas burner or heat from electric hob zones without a pan on
them.
o Do not attempt to use the cooker hood if it is damaged in any
way. Never attempt to use it without the grease filter fitted or if
the filter is excessively greasy!
o Never flambé cook under this cooker hood.
o The lights on this appliance should only be used during operation
of the cooker hood. They should not be left on permanently and
used as a lighting source.
THE MANUFACTURER DECLINES ALL
RESPONSIBILITY IN THE EVENT OF FAILURE TO
OBSERVE THE INSTRUCTIONS GIVEN HERE, FOR
INSTALLATION, MAINTENANCE AND SUITABLE
USE OF THE HOOD.
7
Specifications of your cooker hood
BT06.8ME
Dimensions:
Height:
Width:
Depth:
395 mm
600 mm
282 mm
Specifications:
o
o
o
o
o
o
o
o
o
1 x Integrated axial motor
Slider control operation
Non-return airflow flap
3 Speeds
1 Light
1 synthetic grease filter
Extraction capacity: 250 m³ / hr
Recirculation capacity: 147 m³ / hr
Noise level: 45 / 50 / 55 dB
Optional extras:
o 1 pair of ST1 carbon filters for air recirculation mode
8
BT08.8ME
Dimensions:
Height:
Width:
Depth:
395 mm
600 mm
282 mm
Specifications:
o
o
o
o
o
o
o
o
o
Twin integrated axial motor
Slider control operation
Non-return airflow flap
3 Speeds
1 Light
1 synthetic grease filter
Extraction capacity: 440 m³ / hr
Recirculation capacity: 208 m³ / hr
Noise level: 47 / 50 / 55
Optional extras:
o 1 pair of ST1 carbon filters for air recirculation mode
9
Using your Baumatic cooker hood
Before first use
IMPORTANT: THIS PROCESS MUST BE FOLLOWED
BEFORE THE COOKER HOOD IS USED FOR THE FIRST
TIME.
o You should clean the appliance using a brand new cloth, with
warm soapy water before using the appliance for the first time.
You should then dry it thoroughly using a soft cloth.
To use your cooker hood
o Make sure that it has been installed by a suitably qualified
person, as per the information contained in Baumatic’s
installation instructions.
o Find the control panel, which can be located by opening the front
panel and looking on the right hand side of the cooker hood.
o There are two sliders on the control panel, which perform
separate functions.
Light ON/OFF slider
0
1
=
=
Light bulb off
Light bulb on
10
Speed control slider
0
=
Off
1
=
Low speed
2
=
Medium speed
3
=
High speed
o The cooker hood can be operated by leaving the speed control
slider on setting 1, 2 or 3 and closing the extractor door. This
will automatically turn the motor off.
o When the extractor door is opened again, the motor will resume
at the last set speed. The same also applies for the light slider
control.
Turning the cooker hood off
You can turn the cooker hood off in two ways.
o The cooker hood can be switched off by setting the motor speed
control to 0.
o You can close the extractor door to switch the cooker hood off
however the motor speed will remain the same when you next
lift the cover up.
IMPORTANT: IDEALLY YOU SHOULD TURN ON YOUR
HOOD TEN MINUTES BEFORE YOU START TO COOK,
OR AT THE VERY LEAST WHEN YOU BEGIN COOKING.
YOU SHOULD ALSO RUN YOUR HOOD FOR TEN
MINUTES AFTER YOU HAVE FINISHED COOKING.
11
Cleaning your Baumatic cooker hood
IMPORTANT: BEFORE CLEANING, ALWAYS ENSURE
THAT YOU HAVE SWITCHED YOUR COOKER HOOD
OFF AT THE OMNI-POLAR SWITCH, SET AT THE
WALL FROM THE CABLE.
Cleaning
o Clean the external parts of your cooker hood with mild liquid
detergent and a new damp cloth.
o Never use abrasive powder, corrosive solvents or brushes.
o Never insert pointed objects into the motor’s protective grid.
o Only clean the control panel and grease filter grill with mild liquid
detergents and a new damp cloth.
o If you are using the appliance in recirculation mode, then be
sure to replace the carbon filters at the recommended interval
(see section on “Fitting the carbon filter”). A build up of grease
could cause a fire hazard.
o Never attempt to clean the area above the grease filter.
The grease filter
o Your cooker hood includes a grease filter which helps to absorb
grease particles to protect your kitchen and furniture from
greasy residues.
o The synthetic filter may become flammable if it becomes
saturated with this greasy residue.
o To prevent this fire hazard, the filter should be replaced
occasionally. Depending on use, this should be done every 3
months, following the method shown in the next section.
o The synthetic grease filter is not washable.
o Replacement synthetic filters can
Baumatic Spares Department.
be
purchased
from
the
12
Maintenance
Removing and changing the grease filter
o Locate the two catches at the base of the filter as shown in the
diagram above (1).
o Insert a finger into each catch and gently lift and pull the filter
outwards (2).
o Ensure the filter unclips from the hood, as shown in the diagram
above (3), before you pull it away.
13
o Remove the metal wires which hold the synthetic filter in place.
o Remove the synthetic filter and replace with a new clean one.
o Reattach the metal wires in their original positions to secure the
synthetic filter in place.
o Refit the filter in the cooker hood.
14
Changing a light bulb
IMPORTANT: BEFORE ATTEMPTING TO CHANGE
A LIGHT BULB, YOU MUST ENSURE THAT YOU
HAVE DISCONNECTED THE COOKER HOOD FROM
YOUR MAINS SUPPLY.
o You should use a suitable screwdriver to loosen the screws
holding the panel into place. Once this is removed, you will have
access to the bulb.
o Prior to touching the light bulbs ensure that they have cooled
down.
o Unscrew the light bulb and insert a new olive shaped bulb with
an E14 coupling 40W (max).
o IMPORTANT: Defective bulbs should be replaced immediately.
o If the lights still do not work, make sure that the bulb is fitted
properly into the housing before you call for technical assistance.
15
o Once the bulb has been replaced, refit the panel by screwing the
screws back into place.
Fitting the carbon filter
If the appliance is going to be used in recirculation mode then it is
necessary to a fit a carbon filter. This will help to absorb unpleasant
odours caused by cooking.
IMPORTANT: BEFORE ATTEMPTING TO FIT OR
REMOVE THE CARBON FILTERS, YOU MUST
ENSURE THAT YOU HAVE DISCONNECTED THE
COOKER HOOD FROM YOUR MAINS SUPPLY.
o Remove the filter by locating the two catches at the base of the
grease filter, as shown in the diagram above (1).
o Insert a finger into each catch and gently lift and pull the filter
outwards (2).
16
o Ensure the filter unclips from the hood, as shown in the diagram
on the previous page, before you pull it away. This will allow you
access to the motor where the carbon filter should be fitted.
o Hook the carbon filter which has two fixing pins (C) onto the
motor (D).
o Turn the carbon filter clockwise (F), until you feel it click into
place.
o Refit the filter, making sure it clips
back into the hood correctly.
o The carbon filters should be replaced
every three months, or if they show
signs of damage. To remove the
carbon filter, turn it anticlockwise so
it unlatches from the motor.
17
Installation
IMPORTANT: Before installation and usage read
all the instructions and make sure that the
voltage (V) and the frequency (Hz) indicated on
the rating plate are exactly the same as the
voltage and frequency in your home. The rating
plate can be found behind the grease filter.
The manufacturer declines all responsibility in the event of the installer
failing to observe all of the accident prevention regulations in force,
which are necessary for normal use and the regular operation of the
electric system.
Electrical connection
YOUR COOKER HOOD IS INTENDED FOR FITTED AND
PERMANENT INSTALLATION.
o The cooker hood’s power cable must be fitted upstream from the
electrical connection, using an omni-polar switch with a contact
distance of at least 3 mm. THE FUSE MUST BE RATED AT 3
AMPS.
WARNING: THIS APPLIANCE MUST BE EARTHED. It
should only be connected by a competent person, using
fixed wiring via a double pole switched fused spur outlet.
(UK ONLY).
We recommend that the appliance is connected by a qualified
electrician, who is a member of the N.I.C.E.I.C. and who will comply
with the I.E.E. and local regulations. The wires in the mains lead are
coloured in accordance with the following UK code:
Blue = Neutral, Brown = Live, Green / Yellow = Ground
If you only find two wires in the main’s lead (blue and brown),
then neither must be connected to the earth terminal.
o As the colours of the wires in the
appliance’s mains lead may not
correspond with the coloured
markings identifying the terminals
in your spur box, please proceed
as follows:
o The blue wire must be connected
to the terminal marked “N”
(neutral), or coloured black.
18
o The brown wire must be connected to the terminal marked “L”
(live), or coloured red.
Before beginning installation
o Check that the product purchased is of a suitable size for the
chosen installation area. In addition check whether there is an
electrical socket available that will be accessible once the hood is
mounted. If the product is going to be used in extraction mode,
then there should also be space to connect a ducting hose to the
outside.
o Carry out all necessary masonry work prior to the fitting of the
cooker hood.
o Ensure that all electrical connections are carried out by a suitably
qualified person.
o Before commencing installation of the cooker hood the grease
filter should be removed.
o Check inside the product and ensure that there is no transit
packaging or any other materials, such as packets of screws,
guarantees etc. These should be removed and kept for future
use.
o If possible, disconnect and move freestanding or slot-in cookers
from their position, to provide easier access to the rear wall and
cupboards. If this is not possible, then a thick, protective
covering should be placed over the worktop, hob top or cooker.
This will help to protect these surfaces from damage and debris.
19
o Select a flat surface for assembling the cooker hood. Cover that
surface with a protective covering and place all cooker hood
parts and fittings on it.
o Do not tile, grout or silicone this appliance to the wall or
cabinetry. This appliance is designed to be surface mounted
only.
Installing your cooker hood
IMPORTANT: YOU WILL HAVE TO DECIDE BEFORE
INSTALLING YOUR COOKER HOOD WHETHER TO USE
IT IN EXTRACTION MODE OR RECIRCULATION
MODE. PLEASE TURN TO PAGES 26-27 NOW TO
UNDERSTAND THE DIFFERENCES BETWEEN THESE
TWO MODES.
o We recommend that at least two people install this hood.
o Your cooker hood should only be fitted to a wall and secured
between two cupboards.
o It must be positioned at least 700
mm above the hob underneath it.
This measurement should be taken
from the highest point on the hob,
including the burners.
IMPORTANT: YOUR COOKER HOOD
SHOULD BE CONNECTED TO YOUR
MAINS SUPPLY AFTER THE REST OF
THE INSTALLATION PROCESS HAS
BEEN COMPLETED.
20
o Remove the filter by locating the two catches at the base of the
filter as shown in the diagram on the previous page (1).
o Insert a finger into each catch and gently lift and pull the filter
outwards (2).
o Ensure the filter unclips from the hood, as shown in the diagram
above (3) before you pull it away.
o Install the cooker hood between two cupboards.
o Drill and insert the screws onto the side boards of the cupboards
(the holes should be no larger than 2 mm). The distance
between the head of the screw and the side board should be 5
mm.
o The distance between the screw and the cooking surface below
should be no less than 1040 mm. If there is not enough room
you can place the screws higher or lower.
21
o Hang the cooker hood onto
the screws between the
two cupboards.
o Push the fan-shaped door frames to the end (fully closed), in
order to ensure the outer edges of the door frames are parallel
to the outer edge of the adjacent cupboards (not the doors).
o Mark the positions where the lower screws are to be fixed.
o Drill the upper hole and fix the screws, ensuring that all four
screws are secured tightly.
o Connect the air outlet board and the air outlet tube.
22
Fitting the décor door
o The décor door should be no less than 16 mm thick, 385 – 700
mm high and weigh no more than 7 kg.
o Pull out the movable fan-shaped
door frames, which are located in
two curved plastic slides on each
side of the cooker hood. They are
prevented from being pulled out too
far by plastic limit clips.
o Taking care not to drop the frame,
pull gently on the plastic limit clips
(1) while opening the door frame
(2). Once the door frame has
cleared the plastic clip, the door
frame can be removed from the
hood.
23
o Place the décor door on a protective surface to avoid damage.
Mark the installation position of the door frame and the size of
the fixed screws to ensure you do not drill too deeply and
damage the décor door.
o If the upper edge of the door is not as high as the upper edge of
the cupboards then you should adjust the size accordingly.
o Mark the positions of the screws on the door and ensure the size
is as accurate as 569+1 mm.
o Fix the fan-shaped door frame on the door with screws, making
sure the frames are symmetrical.
o Install the door onto the cooker hood. The two slides of the door
frames can be pulled to the end and door can be safely locked
into position by the plastic limit clips. This prevents accidental
removal of the door frame from the appliance.
o The two screws on both
sides of the cooker hood
can be adjusted to alter
the sliding of the door,
according to its weight.
24
o Install the adjusting plate, in order to cover the gap between the
wall and the bottom of the cooker hood, by screwing it into
place.
Connecting to external ducting
Recirculation:
Ducted out:
o To use the appliance in extraction mode it is necessary to install
external ducting.
o Select a position that is suitable for the location of the cooker
hood and will be accessible once the cooker hood is installed. Cut
out a circle measuring 130 mm in diameter.
o The discharge outlet should be suitable for cooking vapours and
it should have a cross section of at least 150 cm².
25
o Fit a suitable ducting terminal (not supplied) to the wall and
connect a 125 mm ducting hose (not supplied) to the terminal.
Genuine spare parts can be obtained by contacting the Baumatic
Spares Department.
o Connect the other end of the ducting hose to the top of the
cooker hood.
o The maximum distance between the cooker hood and your
discharge outlet should be 3 metres with one 90° bend. For each
additional 90° bend, the maximum distance is reduced by 1
metre.
Extraction mode or recirculation mode?
IMPORTANT: YOU WILL HAVE TO DECIDE BEFORE
INSTALLING YOUR COOKER HOOD WHETHER TO USE
IT IN EXTRACTION MODE OR RECIRCULATION
MODE.
What is the difference between extraction and recirculation
modes?
In extraction mode, the stale air will be taken via the grease filter and
out of the room via external ducting.
In recirculation mode stale air is taken via the grease filter, and passed
through charcoal filters for purification. The air then re-enters the
kitchen via an opening in the hood.
For optimum performance, we recommend that the cooker hood is
used in extraction mode and connected to external ducting.
Unfortunately if you live in a flat or the hood is too far from an outside
wall, this may not be possible. The only alternative is to recirculate the
air.
Do I need a charcoal filter?
All cooker hoods have a grease filter but if you are using your cooker
hood in recirculation mode, then charcoal filters must be fitted in
addition to the grease filter.
Completing the installation
If you are setting the appliance to recirculation mode, then you should
now fit the two carbon filter(s). See the “Fitting the carbon filters”
section on page 16 - 17.
26
The electrical connection must correspond to the electrical requirement
noted on the rating plate, which is placed inside the cooker hood. The
appliance should now be connected to the electrical supply. See page
18 – 19 for detailed information on the electrical connection.
Refit the grease filter(s) and then switch on the mains
supply to the appliance. Check that the appliance is
operating correctly by selecting each speed and switching
the light bulbs on and off.
Troubleshooting
IMPORTANT: If your cooker hood appears not to be
operating properly, before contacting the Baumatic
Service Department, please refer to the checklist
below.
My cooker hood will not start.
o Check that the hood is connected to the electricity supply
o Check that the fan speed control is set correctly.
My cooker hood is not working effectively.
o The fan speed is not set high enough
o The grease filter is dirty and requires replacing.
o The kitchen is not well ventilated enough.
o If the hood is set up for recirculation mode, check that the
carbon filters do not need replacing.
o If the hood is set up for extraction mode, check that the ducting
hose and discharge outlet are not blocked.
My cooker hood has switched off during operation.
o The safety cut-out device has been tripped.
27
o Turn off the hob and then wait for the safety cut-out device to
reset.
o IMPORTANT: If you have installed your cooker hood too low,
the safety cut-out device will frequently trip. Your cooker hood
may become damaged if the safety cut-out device is tripped
frequently.
IMPORTANT: If your appliance appears not to be
operating correctly, then you should disconnect it
from your mains supply and then contact the
Baumatic Service Department on telephone
number (0118) 933 6911.
DO NOT ATTEMPT TO REPAIR THE APPLIANCE
YOURSELF.
Please note that if an engineer is asked to attend whilst the product is
under guarantee and finds that the problem is not the result of an
appliance fault, then you may be liable for the cost of the call out
charge.
The appliance must be accessible for the engineer to perform
any necessary repair. If your appliance is installed in such a
way that an engineer is concerned that damage will be caused
to the appliance or your kitchen, then he will not complete a
repair.
This includes situations where appliances have been tiled in,
sealed in with sealant, have wooden obstructions placed in
front of the appliance, like plinths. Or any installation other
than the one specified by Baumatic Ltd. has been completed.
Please refer to the conditions of guarantee that appear on the
warranty card that you receive with the appliance when it is delivered.
28
Baumatic Consumables
o BC001 Degreaser for Dishwashers (200 g)
o BC002 Descaler for Washing Machines and Dishwashers (200 g)
o BC003 Ceramic Hob Cleaner (250 ml)
o BC004 Oven Cleaner (250 ml)
o BC005 Stainless Steel Cleaner and Protector (250 ml)
o BC007 E-Cloth – General Purpose Cloth
o BC008 Microwave Cover
To order a Baumatic consumable product please call 0123 5437 244
and quote the product code. You can also order online from
eshop.baumatic.co.uk
29
United Kingdom
Baumatic Ltd.,
Baumatic Buildings,
6 Bennet Road,
Reading, Berkshire
RG2 0QX
United Kingdom
Czech Republic
Baumatic CR spol s.r.o.
Lìpovà 665
460 01 Liberec 4
Czech Republic
Sales Telephone
(0118) 933 6900
Sales Fax
(0118) 931 0035
Customer Care Telephone
(0118) 933 6911
Customer Care Fax
(0118) 986 9124
Spares Telephone
(01235) 437244
Advice Line Telephone
(0118) 933 6933
www.baumatic.cz
E-mail:
sales@baumatic.co.uk
customercare@baumatic.co.uk
spares@baumatic.co.uk
technical@baumatic.co.uk
Website:
www.baumatic.co.uk
Facebook:
www.facebook.com/baumatic.uk
Republic of Ireland
Service Telephone
1-890 812 724
Spares Telephone
091 756 771
+420 483 577 200
Slovakia
Baumatic Slovakia, s.r.o.
Galvániho 7/D
Slovakia
+421 255 640 618
Germany
Baumatic Gmbh
Bachstr.10-12
D-32 257 Bünde
Deutschland
+49 (0) 5223 99408 0
www.baumatic.de
Italy
Baumatic Italia S.R.L.
Via Galvani N.3
35011 Campodarsego (PD)
+3904 9920 2297
www.baumatic.it
Holland
Baumatic Benelux B.V.
Dukdalfweg 15d
1332 BH ALMERE
Nederland
+31(0)36 549 1553
www.baumatic.nl
30
31
32
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising