SFP-1000-SR 10Gbps SFP+ Optical Transceiver, 300m Reach Features

SFP-1000-SR 10Gbps SFP+ Optical Transceiver, 300m Reach Features
SFP-1000-SR
10Gbps SFP+ Optical Transceiver, 300m Reach
Features
Optical interface compliant to IEEE 802.3ae 10GBASE-SR
Electrical interface compliant to SFF-8431
Hot Pluggable
850nm VCSEL transmitter, PIN photo-detector
Maximum link length of 300m on 2000MHz/km MMF
Operating case temperature: 0 to 70℃
Low power consumption
All-metal housing for superior EMI performance
Advanced firmware allow customer system encryption information to be stored in transceiver
Cost effective SFP+ solution, enables higher port densities and greater bandwidth
Applications
10GBASE-SR at 10.3125Gbps
10GBASE-SW at 9.953Gbps
Other optical links
Product description
This 850 nm VCSEL 10 Gigabit SFP+ transceiver is designed to transmit and receive optical data over
50/125 μm or 62.5/125 μm multimode optical fiber (Table 1).
Table 1: SFP+ SR Operating Range for each Optical Fiber Type
The SFP+ SR module electrical interface is compliant to SFI electrical specifications. The transmitter
input and receiver output impedance is 100 Ohms differential. Data lines are internally AC coupled.
Robofiber, Inc., 2491 Estand Way, Pleasant Hill, CA 94523 US
Page 1 of 9
Rev.1.4 Apr 26/2013
The module provides differential termination and reduce differential to common mode conversion for
quality signal termination and low EMI. SFI typically operates over 200mm of improved FR4 material or
up to about 150mm of standard FR4 with one connector.
The transmitter converts 10Gbit/s serial PECL or CML electrical data into serial optical data compliant with
the 10GBASE-SR standard. An open collector compatible Transmit Disable (Tx_Dis) is provided. A logic
“1,” or no connection on this pin will disable the laser from transmitting. A logic “0” on this pin provides
normal operation. The transmitter has an internal automatic power control loop (APC) to ensure constant
optical power output across supply voltage and temperature variations. An open collector compatible
Transmit Fault (TFault) is provided. TX_Fault is a module output contact that when high, indicates that the
module transmitter has detected a fault condition related to laser operation or safety. The TX_Fault output
contact is an open drain/collector and shall be pulled up to the Vcc_Host in the host with a resistor in the
range 4.7-10 kΩ. TX_Disable is a module input contact. When TX_Disable is asserted high or left open,
the SFP+ module transmitter output shall be turned off. This contact shall be pulled up to VccT with a 4.7
kΩ to 10 kΩ resistor
The receiver converts 10Gbit/s serial optical data into serial PECL/CML electrical data. An open collector
compatible Loss of Signal is provided. Rx_LOS when high indicates an optical signal level below that
specified in the relevant standard. The Rx_LOS contact is an open drain/collector output and shall be
pulled up to Vcc_Host in the host with a resistor in the range 4.7-10 kΩ, or with an active termination.
Power supply filtering is recommended for both the transmitter and receiver. The Rx_LOS signal is
intended as a preliminary indication to the system in which the SFP+ is installed that the received signal
strength is below the specified range. Such an indication typically points to non-installed cables, broken
cables, or a disabled, failing or a powered off transmitter at the far end of the cable.
Figure 1: Interface to Host
Pin definition
The SFP+ modules are hot-pluggable. Hot pluggable refers to plugging in or unplugging a module while
the host board is powered. The SFP+ host connector is a 0.8 mm pitch 20 position right angle improved
connector specified by SFF-8083, or stacked connector with equivalent with equivalent electrical
Robofiber, Inc., 2491 Estand Way, Pleasant Hill, CA 94523 US
Page 2 of 9
Rev.1.4 Apr 26/2013
performance.
Host PCB contact assignment is shown in Figure 2 and contact definitions are given in
Table 2.
SFP+ module contacts mates with the host in the order of ground, power, followed by signal as
illustrated by Figure 3 and the contact sequence order listed in Table 2.
Figure 2: Interface to Host PCB
Figure 3: Module Contact Assignment
Robofiber, Inc., 2491 Estand Way, Pleasant Hill, CA 94523 US
Page 3 of 9
Rev.1.4 Apr 26/2013
Table 2: SFP+ Module PIN Definition
Robofiber, Inc., 2491 Estand Way, Pleasant Hill, CA 94523 US
Page 4 of 9
Rev.1.4 Apr 26/2013
Absolute maximum rating
These values represent the damage threshold of the module. Stress in excess of any of the individual
Absolute Maximum Ratings can cause immediate catastrophic damage to the module even if all other
parameters are within Recommended Operating Conditions.
Parameters
Symbol
Min.
Max.
Unit
Power Supply Voltage
VCC
0
+3.6
V
Storage Temperature
Tc
-40
+85
C
Operating Case Temperature
Tc
-5
+75
C
Relative Humidity
RH
5
95
%
RX Input Average Power
Pmax
-
0
dBm
Table 3: Absolute Maximum Rating
Recommended operating environment
Recommended Operating Environment specifies parameters for which the electrical and optical
characteristics hold unless otherwise noted.
Parameter
Symbol
Min.
Typical
Max
Unit
Power Supply Voltage
VCC
3.135
3.300
3.465
V
Operating Case Temperature
TC
0
25
70
C
Table 4: Recommended Operating Environment
Robofiber, Inc., 2491 Estand Way, Pleasant Hill, CA 94523 US
Page 5 of 9
Rev.1.4 Apr 26/2013
Optical characteristics
The following optical characteristics are defined over the Recommended Operating Environment unless
otherwise specified.
Parameter
Symbol
Min.
Typical
Max
Unit
Notes
Transmitter
Center Wavelength
λt
840
850
860
nm
RMS spectral width
Pm
-
-
Note 1
nm
Average Optical Power
Pavg
-6.5
-
-1
dBm
2
Extinction Ratio
ER
3.5
-
-
dB
3
Transmitter Dispersion Penalty
TDP
-
-
3.9
dB
Relative Intensity Noise
Rin
-
-
-128
dB/Hz
-
-
12
dB
Optical Return Loss Tolerance
12dB reflection
Receiver
Center Wavelength
λr
840
850
860
nm
Receiver Sensitivity
Psens
-
-
-11.1
dBm
4
-
-
-7.5
dBm
4
Stressed Sensitivity in OMA
Los function
Los
-30
-
-12
dBm
Overload
Pin
-
-
-1.0
dBm
-
-
-12
dB
Receiver Reflectance
4
Note 1.Trade-offs are available between spectral width, center wavelength and minimum OMA, as shown in table 6.
2.The optical power is launched into MMF
31
3.Measured with a PRBS 2 -1 test pattern @10.3125Gbps
31
-12.
4.Measured with a PRBS 2 -1 test pattern @10.3125Gbps,BER≤10
Table 5: Optical Characteristics
Table 6: Minimum 10GBASE-SR OMA as a Function of Wavelength and Spectral Width
Robofiber, Inc., 2491 Estand Way, Pleasant Hill, CA 94523 US
Page 6 of 9
Rev.1.4 Apr 26/2013
Digital Diagnostic Functions
The following digital diagnostic characteristics are defined over the Recommended Operating
Environment unless otherwise specified. It is compliant to SFF8472 Rev9.2 with internal calibration mode.
For external calibration mode please contact our sales stuff.
Parameter
Symbol
Min.
Max
Unit
Notes
Temperature monitor absolute error
DMI_Temp
-3
+3
degC
Over operating temp
Laser power monitor absolute error
DMI_TX
-3
+3
dB
RX power monitor absolute error
DMI_RX
-3
+3
dB
-3dBm to -12dBm
range
Supply voltage monitor absolute error
DMI_VCC
-0.08
+0.08
V
Full operating range
Bias current monitor
DMI_Ibias
-10%
10%
mA
Electrical characteristics
The following electrical characteristics are defined over the Recommended Operating Environment unless
otherwise specified.
Parameter
Symbol
Min.
Typical
Max
Unit
Notes
Data Rate
-
10.3125
-
Gbps
Power Consumption
-
600
800
mW
Transmitter
Single Ended Output Voltage Tolerance
-0.3
-
4.0
V
C common mode voltage tolerance
15
-
-
mV
Tx Input Diff Voltage
VI
180
1200
mV
Tx Fault
VoL
-0.3
0.4
V
Data Dependent Input Jitter
DDJ
0.10
UI
Data Input Total Jitter
TJ
0.28
UI
4.0
V
850
mV
At 0.7mA
Receiver
Single Ended Output Voltage Tolerance
-0.3
-
Rx Output Diff Voltage
Vo
300
Rx Output Rise and Fall Time
Tr/Tf
30
Total Jitter
TJ
0.70
UI
Deterministic Jitter
DJ
0.42
UI
ps
20% to 80%
Table 7: Electrical Characteristics
Robofiber, Inc., 2491 Estand Way, Pleasant Hill, CA 94523 US
Page 7 of 9
Rev.1.4 Apr 26/2013
Control and status I/O timing characteristics
Timing characteristics of control and status I/O are included in Table 8, which is also defined in SFF-8431.
Table 8: Timing Characteristics
Robofiber, Inc., 2491 Estand Way, Pleasant Hill, CA 94523 US
Page 8 of 9
Rev.1.4 Apr 26/2013
Mechanical
Table 9: Key Mechanical Dimensions
ESD
This transceiver is specified as ESD threshold 2kV for all electrical input pins, tested per MIL-STD-883,
Method 3015.4 /JESD22-A114-A (HBM). However, normal ESD precautions are still required during the
handling of this module. This transceiver is shipped in ESD protective packaging. It should be removed
from the packaging and handled only in an ESD protected environment.
LASER SAFETY
This is a Class 1 Laser Product according to IEC 60825-1:1993:+A1:1997+A2:2001. This product
complies with 21 CFR 1040.10 and 1040.11 except for deviations pursuant to Laser Notice No. 50, dated
(July 26, 2001)
Ordering information
Part Number
SFP-1000-SR
Product Description
850nm, 10Gbps, 300m,
0ºC ~ +70ºC
E-mail: sales@robofiber.com
Robofiber, Inc., 2491 Estand Way, Pleasant Hill, CA 94523 US
Page 9 of 9
Rev.1.4 Apr 26/2013
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising