Yamaha | PSR-S650 | Owner`s manual | Yamaha PSR-S650 Owner's manual

DIGITAL WORKSTATION
Owner’s Manual
Before using the instrument, be sure to read “PRECAUTIONS” on pages 4-5.
EN
SPECIAL MESSAGE SECTION
This product utilizes batteries or an external power supply (adapter).
DO NOT connect this product to any power supply or adapter other
than one described in the manual, on the name plate, or specifically
recommended by Yamaha.
WARNING: Do not place this product in a position where anyone could
walk on, trip over, or roll anything over power or connecting cords of any
kind. The use of an extension cord is not recommended! If you must use an
extension cord, the minimum wire size for a 25’ cord (or less) is 18 AWG.
NOTE: The smaller the AWG number, the larger the current handling
capacity. For longer extension cords, consult a local electrician.
This product should be used only with the components supplied or; a
cart, rack, or stand that is recommended by Yamaha. If a cart, etc., is
used, please observe all safety markings and instructions that accompany the accessory product.
SPECIFICATIONS SUBJECT TO CHANGE:
The information contained in this manual is believed to be correct at
the time of printing. However, Yamaha reserves the right to change or
modify any of the specifications without notice or obligation to update
existing units.
This product, either alone or in combination with an amplifier and
headphones or speaker/s, may be capable of producing sound levels
that could cause permanent hearing loss. DO NOT operate for long
periods of time at a high volume level or at a level that is uncomfortable. If you experience any hearing loss or ringing in the ears, you
should consult an audiologist.
IMPORTANT: The louder the sound, the shorter the time period before
damage occurs.
Some Yamaha products may have benches and / or accessory
mounting fixtures that are either supplied with the product or as
optional accessories. Some of these items are designed to be dealer
assembled or installed. Please make sure that benches are stable and
any optional fixtures (where applicable) are well secured BEFORE
using.
Benches supplied by Yamaha are designed for seating only. No other
uses are recommended.
Battery Notice:
This product MAY contain a small non-rechargeable battery which (if
applicable) is soldered in place. The average life span of this type of battery is approximately five years. When replacement becomes necessary,
contact a qualified service representative to perform the replacement.
This product may also use “household” type batteries. Some of these
may be rechargeable. Make sure that the battery being charged is a
rechargeable type and that the charger is intended for the battery being
charged.
When installing batteries, never mix old batteries with new ones, and
never mix different types of batteries. Batteries MUST be installed correctly. Mismatches or incorrect installation may result in overheating and
battery case rupture.
Warning:
Do not attempt to disassemble, or incinerate any battery. Keep all batteries away from children. Dispose of used batteries promptly and as
regulated by the laws in your area. Note: Check with any retailer of
household type batteries in your area for battery disposal information.
Disposal Notice:
Should this product become damaged beyond repair, or for some reason its useful life is considered to be at an end, please observe all
local, state, and federal regulations that relate to the disposal of products that contain lead, batteries, plastics, etc. If your dealer is unable
to assist you, please contact Yamaha directly.
NAME PLATE LOCATION:
The name plate is located on the bottom of the product. The model
number, serial number, power requirements, etc., are located on this
plate. You should record the model number, serial number, and the
date of purchase in the spaces provided below and retain this manual
as a permanent record of your purchase.
Model
NOTICE:
Service charges incurred due to a lack of knowledge relating to how a
function or effect works (when the unit is operating as designed) are
not covered by the manufacturer’s warranty, and are therefore the
owners responsibility. Please study this manual carefully and consult
your dealer before requesting service.
ENVIRONMENTAL ISSUES:
Yamaha strives to produce products that are both user safe and environmentally friendly. We sincerely believe that our products and the
production methods used to produce them, meet these goals. In keeping with both the letter and the spirit of the law, we want you to be
aware of the following:
92-BP (bottom)
Serial No.
Purchase Date
PLEASE KEEP THIS MANUAL
FCC INFORMATION (U.S.A.)
1. IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT!
This product, when installed as indicated in the instructions contained in this manual, meets FCC requirements. Modifications not
expressly approved by Yamaha may void your authority, granted by
the FCC, to use the product.
2. IMPORTANT: When connecting this product to accessories and/
or another product use only high quality shielded cables. Cable/s
supplied with this product MUST be used. Follow all installation
instructions. Failure to follow instructions could void your FCC
authorization to use this product in the USA.
3. NOTE: This product has been tested and found to comply with the
requirements listed in FCC Regulations, Part 15 for Class “B” digital
devices. Compliance with these requirements provides a reasonable level of assurance that your use of this product in a residential
environment will not result in harmful interference with other electronic devices. This equipment generates/uses radio frequencies
and, if not installed and used according to the instructions found in
the users manual, may cause interference harmful to the operation
of other electronic devices. Compliance with FCC regulations does
* This applies only to products distributed by YAMAHA CORPORATION OF AMERICA.
2
not guarantee that interference will not occur in all installations. If
this product is found to be the source of interference, which can be
determined by turning the unit “OFF” and “ON”, please try to eliminate the problem by using one of the following measures:
Relocate either this product or the device that is being affected by
the interference.
Utilize power outlets that are on different branch (circuit breaker or
fuse) circuits or install AC line filter/s.
In the case of radio or TV interference, relocate/reorient the
antenna. If the antenna lead-in is 300 ohm ribbon lead, change the
lead-in to co-axial type cable.
If these corrective measures do not produce satisfactory results,
please contact the local retailer authorized to distribute this type of
product. If you can not locate the appropriate retailer, please contact Yamaha Corporation of America, Electronic Service Division,
6600 Orangethorpe Ave, Buena Park, CA90620
The above statements apply ONLY to those products distributed by
Yamaha Corporation of America or its subsidiaries.
(class B)
COMPLIANCE INFORMATION STATEMENT
(DECLARATION OF CONFORMITY PROCEDURE)
Responsible Party : Yamaha Corporation of America
Address : 6600 Orangethorpe Ave., Buena Park,
Calif. 90620
Telephone : 714-522-9011
Type of Equipment : Digital Keyboard
Model Name : PSR-S650
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
1) this device may not cause harmful interference, and
2) this device must accept any interference received including
interference that may cause undesired operation.
See user manual instructions if interference to radio reception is
suspected.
* This applies only to products distributed by
YAMAHA CORPORATION OF AMERICA.
(FCC DoC)
3
PRECAUTIONS
PLEASE READ CAREFULLY BEFORE PROCEEDING
* Please keep this manual in a safe place for future reference.
WARNING
Always follow the basic precautions listed below to avoid the possibility of serious injury or even death from electrical shock, shortcircuiting, damages, fire or other hazards. These precautions include, but are not limited to, the following:
Power supply/AC power adaptor
Water warning
• Do not place the power cord near heat sources such as heaters or radiators, and
do not excessively bend or otherwise damage the cord, place heavy objects on it,
or place it in a position where anyone could walk on, trip over, or roll anything
over it.
• Only use the voltage specified as correct for the instrument. The required voltage
is printed on the name plate of the instrument.
• Use the specified adaptor (page 70) only. Using the wrong adaptor can result in
damage to the instrument or overheating.
• Check the electric plug periodically and remove any dirt or dust which may have
accumulated on it.
Do not open
• This instrument contains no user-serviceable parts. Do not open the instrument
or attempt to disassemble or modify the internal components in any way. If it
should appear to be malfunctioning, discontinue use immediately and have it
inspected by qualified Yamaha service personnel.
• Do not expose the instrument to rain, use it near water or in damp or wet
conditions, place on it any containers (such as vases, bottles or glasses)
containing liquids which might spill into any openings. If any liquid such as water
seeps into the instrument, turn off the power immediately and unplug the power
cord from the AC outlet. Then have the instrument inspected by qualified Yamaha
service personnel.
• Never insert or remove an electric plug with wet hands.
Fire warning
• Do not put burning items, such as candles, on the unit.
A burning item may fall over and cause a fire.
If you notice any abnormality
• When one of the following problems occur, immediately turn off the power switch
and disconnect the electric plug from the outlet. Then have the device inspected
by Yamaha service personnel.
• The power cord or plug becomes frayed or damaged.
• It emits unusual smells or smoke.
• Some object has been dropped into the instrument.
• There is a sudden loss of sound during use of the instrument.
CAUTION
Always follow the basic precautions listed below to avoid the possibility of physical injury to you or others, or damage to the
instrument or other property. These precautions include, but are not limited to, the following:
• Use only the stand specified for the instrument. When attaching the stand or rack,
use the provided screws only. Failure to do so could cause damage to the internal
components or result in the instrument falling over.
Power supply/AC power adaptor
• Do not connect the instrument to an electrical outlet using a multiple-connector.
Doing so can result in lower sound quality, or possibly cause overheating in the
outlet.
• When removing the electric plug from the instrument or an outlet, always hold the
plug itself and not the cord. Pulling by the cord can damage it.
• Remove the electric plug from the outlet when the instrument is not to be used for
extended periods of time, or during electrical storms.
Location
• Do not place the instrument in an unstable position where it might accidentally
fall over.
• Before moving the instrument, remove all connected cables.
• When setting up the product, make sure that the AC outlet you are using is easily
accessible. If some trouble or malfunction occurs, immediately turn off the power
switch and disconnect the plug from the outlet. Even when the power switch is
turned off, electricity is still flowing to the product at the minimum level. When
you are not using the product for a long time, make sure to unplug the power cord
from the wall AC outlet.
Connections
• Before connecting the instrument to other electronic components, turn off the
power for all components. Before turning the power on or off for all components,
set all volume levels to minimum.
• Be sure to set the volumes of all components at their minimum levels and
gradually raise the volume controls while playing the instrument to set the desired
listening level.
Handling caution
• Do not insert a finger or hand in any gaps on the instrument.
• Never insert or drop paper, metallic, or other objects into the gaps on the panel or
keyboard. This could cause physical injury to you or others, damage to the
instrument or other property, or operational failure.
• Do not rest your weight on, or place heavy objects on the instrument, and do not
use excessive force on the buttons, switches or connectors.
• Do not use the instrument/device or headphones for a long period of time at a
high or uncomfortable volume level, since this can cause permanent hearing loss.
If you experience any hearing loss or ringing in the ears, consult a physician.
Yamaha cannot be held responsible for damage caused by improper use or modifications to the instrument, or data that is lost or destroyed.
Always turn the power off when the instrument is not in use.
Even when the power switch is in standby status, electricity is still flowing to the instrument at the minimum level. When you are not using the instrument for a long time, make
sure you unplug the power cord from the wall AC outlet.
DMI-3
4
Owner’s Manual
1/2
NOTICE
To avoid the possibility of malfunction/ damage to the product, damage to data, or damage to other property, follow the
notices below.
 Handling and Maintenance
• Do not use the instrument in the vicinity of a TV, radio, stereo equipment, mobile phone, or other electric devices. Otherwise, the instrument, TV, or radio
may generate noise.
• Do not expose the instrument to excessive dust or vibrations, or extreme cold or heat (such as in direct sunlight, near a heater, or in a car during the day)
to prevent the possibility of panel disfiguration, damage to the internal components or unstable operation. (Verified operating temperature range: 5° –
40°C, or 41° – 104°F.)
• Do not place vinyl, plastic or rubber objects on the instrument, since this might discolor the panel or keyboard.
• When cleaning the instrument, use a soft, cloth. Do not use paint thinners, solvents, cleaning fluids, or chemical-impregnated wiping cloths.
 Saving data
• Some data items (page 53) are automatically saved as backup data in the internal memory even if you turn the power off. Saved data may be lost due to
malfunction or incorrect operation. Save important data to a USB flash memory (pages 57–58) or a computer (refer to the Reference Manual.)
To protect against data loss through media damage, we recommend that you save your important data onto two USB storage devices/external media.
Information
 About copyrights
• Copying of the commercially available musical data including but not limited to MIDI data and/or audio data is strictly prohibited except for your personal
use.
• This product incorporates and bundles computer programs and contents in which Yamaha owns copyrights or with respect to which it has license to use
others’ copyrights. Such copyrighted materials include, without limitation, all computer software, style files, MIDI files, WAVE data, musical scores and
sound recordings. Any unauthorized use of such programs and contents outside of personal use is not permitted under relevant laws. Any violation of
copyright has legal consequences. DON’T MAKE, DISTRIBUTE OR USE ILLEGAL COPIES.
 About functions/data bundled with the instrument
• Some of the preset songs have been edited for length or arrangement, and may not be exactly the same as the original.
• This device is capable of using various types/formats of music data by optimizing them to the proper format music data for use with the device in advance.
As a result, this device may not play them back precisely as their producers or composers originally intended.
 About this manual
• The illustrations and displays as shown in this manual are for instructional purposes only, and may appear somewhat different from those on your
instrument.
• Windows is a registered trademark of Microsoft® Corporation in the United States and other countries.
• Apple, Mac and Macintosh are trademarks of Apple Inc., registered in the U.S. and other countries.
• The bitmap fonts used in this instrument have been provided by and are the property of Ricoh Co., Ltd.
• The company names and product names in this manual are the trademarks or registered trademarks of their respective companies.
Supplied Accessories
• Owner’s Manual (this book)
• Data List
• AC power adaptor
* May not be included depending on your particular area. Please check with your Yamaha dealer.
• My Yamaha Product User Registration
* The PRODUCT ID on the sheet will be needed when you fill out the User Registration form.
• Music rest
DMI-3
2/2
Owner’s Manual
5
Formats
The instrument is compatible with the following formats.
GM System Level 2
XF
“GM (General MIDI)” is one of the most common
Voice allocation formats. “GM System Level 2” is a
standard specification that enhances the original
“GM” and improves Song data compatibility.
The Yamaha XF format enhances the SMF
(Standard MIDI File) standard with greater
functionality and open-ended expandability for
the future. This instrument is capable of displaying lyrics when an XF file containing lyric
data is played.
XG
XG is a major enhancement of the GM System
Level 1 format, and was developed by Yamaha specifically to provide more Voices and variations, as
well as greater expressive control over Voices and
effects, and to ensure compatibility of data well into
the future.
GS
GS was developed by the Roland Corporation. In the
same way as Yamaha XG, GS is a major enhancement of the GM specifically to provide more Voices
and Drum kits and their variations, as well as greater
expressive control over Voices and effects.
SFF GE (Guitar Edition)
“SFF (Style File Format)” is an original Style
file format by Yamaha which uses a unique conversion system to provide high-quality automatic accompaniment based on a wide range of
chord types. “SFF GE (Guitar Edition)” is an
enhanced format of SFF, which features
improved note transposition for guitar tracks.
USB
USB is an abbreviation for Universal Serial
Bus. It is a serial interface for connecting a
computer with peripheral Devices. It allows
“hot swapping” (connecting peripheral devices
while the power to the computer is on).
About the Manuals
 Included Documents
Owner’s Manual (this book)
Provides overall explanations of the PSR-S650 basic functions. In this Owner’s Manual, the “Contents” on page 7,
the “Panel Controls and Terminals” on page 8, and the “Panel Button Chart” on page 65 should be used when you
are searching for a specific function or information The “Contents” lists basic functions of the instrument, the
“Panel Controls and Terminals” provides summary about the panel controls and connectors, and the “Panel Button
Chart” lists all the displays called up from the panel controls. Use one of the methods described above to find the
information you are looking for.
Data List
Contains various important preset content lists such as Voices, Styles and Effects.
 Online Materials (Downloadable from the web)
The following instructional materials are available for downloading from the Yamaha Manual Library. Access the Yamaha
Manual Library, then enter your model name (PSR-S650, for example) in the Model Name area to search the manuals.
Yamaha Manual Library http://www.yamaha.co.jp/manual/
Reference Manual (Only in English, German, French, Spanish, Portuguese, Russian, Chinese and Japanese)
Explains advanced features of the PSR-S650. After reading the Owner’s Manual and you want more detailed information about PSR-S650 features, refer to the Reference Manual. To check which manual, Owner’s or Reference,
contains descriptions of the desired function, refer to the Panel Button Chart on page 65.
MIDI Reference (Only in English)
Contains both the MIDI Data Format and the MIDI Implementation Chart, which allows you to confirm MIDI messages transmitted/recognized by this instrument.
6
Owner’s Manual
Contents
Supplied Accessories................................................. 5
Formats...................................................................... 6
About the Manuals ..................................................... 6
Panel Controls and Terminals
Setting Up
8
5
Playing with the Music Database
46
6
Mixer
47
7
Memorizing Your Favorite Panel Settings 49
10
Memorizing the Panel Settings................................ 50
Recalling the Memorized Panel Settings................. 50
Power Requirements ............................................... 10
Registration Clear—Deleting the Specified
Registration Memory............................................ 52
Auto Power Off Function.......................................... 10
Connecting a Footswitch.......................................... 10
Connecting Headphones and External Audio
Equipment ............................................................ 11
8
Adjusting the Display CONTRAST control............... 12
1
Initialization.............................................................. 53
9
Using USB Flash Memory
54
Displays and Basic Operation.................................. 13
File Control Display ................................................. 55
Voices – Playing the Keyboard –
Formatting USB Flash Memory ............................... 56
16
Saving the Registration Memory ............................. 57
Select and Play a Main Voice .................................. 16
Saving a User Song or User Style........................... 58
Playing Two Voices Simultaneously ........................ 17
Loading a File .......................................................... 59
Splitting the Keyboard and Playing the Left Voice
with the Left Hand ................................................ 17
Deleting Data from USB Flash Memory .................. 60
Playing Drum Kits .................................................... 18
Applying Effects to a Voice ...................................... 19
Changing the Pitch of the Instrument....................... 20
Scale Tuning ............................................................ 22
Touch Response ON/OFF ....................................... 26
Using the Metronome............................................... 27
2
53
Backup Data and Memory Data .............................. 53
Turning the Power On.............................................. 11
Changing the Display Language.............................. 12
Initialization
Styles
– Playing Rhythm and Accompaniment – 29
10 Expanding Voices and Styles
(Installing to the Expansion Category)
61
11 Connecting to a Computer
63
Appendix
64
Troubleshooting....................................................... 64
Panel Button Chart .................................................. 65
Messages ................................................................ 67
Select and Play a Style ............................................ 29
Specifications .......................................................... 69
Changing the Tempo ............................................... 34
Index........................................................................ 71
One Touch Setting ................................................... 34
3
Using Songs
35
Selecting and Listening to a Song ........................... 35
Changing the Tempo ............................................... 36
Fast Forward, Fast Reverse, and Pause ................. 36
Listening to the Demo Song..................................... 37
Select and Play a Song from USB Flash Memory ... 37
Displaying the Song Score....................................... 38
Displaying the Lyrics ................................................ 38
A-B Repeat .............................................................. 39
4
Recording Your Own Performance
40
The other functions such as the following ones are described in
the Reference Manual.
• Style Creator
• Song Edit
• Style related functions:
Style Volume, Track Mute
• Song related functions:
Song Volume, Track Mute, Right-Part, Left-part
• MIDI related functions:
PC Mode, Local, External Clock, Keyboard Out, Style Out,
Song Out, Initial Setup
Quick Recording Procedure..................................... 40
Multi-track Recording Procedure ............................. 41
Song Clear—Deleting User Songs .......................... 44
Track Clear—Deleting a Specified Track
From a User Song................................................ 45
Owner’s Manual
7
Panel Controls and Terminals
Front Panel
q
e
w
r
t
i
y
!1
!2 !3
!4
u
o
!0
!5
@4
Front Panel
q [
] (Standby/On) switch .................... page 11
Turns the instrument’s power on or Standby.
w MASTER VOLUME control .................. page 11
Adjusts the overall volume.
e [DEMO] button......................................page 37
Plays the Demo.
r [SONG MODE] button ..........................page 35
Switches between Song mode and Style mode.
t SONG buttons ......................................page 35
Selects a Song or show music score and lyrics.
y [USB] button .........................................page 35
Selects a Song or Style file in the USB flash memory.
u [REC] button .........................................page 40
Records your keyboard performance.
i STYLE category selection buttons.....page 29
Selects a Style.
o STYLE CONTROL buttons........... pages 30–31
Controls Style playback.
!0 SONG CONTROL buttons ................... page 36
Controls Song playback.
!1 TRANSPOSE buttons .......................... page 20
Transposes the pitch in semitone steps.
!2 METRONOME button ........................... page 27
Plays the Metronome.
!3 TEMPO buttons .................................... page 34
Controls the tempo for Style, Song and Metronome
playback.
!4 REGISTRATION MEMORY-related buttons
............................................................... page 49
Lets you execute the function such as changing a Bank
and memorizing the panel settings.
!5 REGISTRATION MEMORY/Track buttons
....................................................... pages 42, 49
Pressing the [REGIST/PART[MIXER]] button at right
will alternate the function of the white eight buttons:
Registration Memory buttons, Song track setting buttons
and Style track setting buttons.
!6 Display and related controls....... pages 13–14
8
Owner’s Manual
Panel Controls and Terminals
NOTE
• The panel controls q–@4 call up the related displays, all of which are listed in the Panel Button Chart on page 65.
!6
@1
!7 !8 !9
@0
@2
@3
Rear Panel
@5
@6
@7
@8
@9
#0
Rear Panel
!7 [MDB] button ........................................page 46
Calls up the appropriate panel settings for the desired
music genre.
!8 [FILE MENU] button .............................page 55
Executes file operations such as loading and saving.
!9 [FUNCTION] button .............................. page 15
Allows you to make the detailed settings.
@0 ONE TOUCH SETTING buttons...........page 34
Calls up the appropriate panel settings for the current
Style.
@1 VOICE category selection buttons ..... page 16
Selects a Voice.
@2 VOICE CONTROL buttons ................... page 19
@5 CONTRAST knob ................................. page 12
Adjusts the contrast of the display.
@6 USB TO HOST terminal ....................... page 63
For connecting to a computer.
@7 USB TO DEVICE terminal .................... page 54
For connecting a USB storage device.
@8 SUSTAIN jack ....................................... page 10
For connecting a footswitch.
@9 PHONES/OUTPUT jack........................ page 11
For connecting headphones, or a powered speaker.
#0 DC IN jack ............................................. page 10
For connecting the power adaptor.
Applies some effects to the keyboard performance.
@3 UPPER OCTAVE buttons .....................page 20
Shifts the pitch of the keyboard in octave steps.
@4 PITCH BEND wheel..............................page 20
Bends the pitch of the keyboard played sound up or
down.
Owner’s Manual
9
Setting Up
Be sure to do the following operations
BEFORE turning on the power.
Make all necessary connections below
BEFORE turning the power on.
Auto Power Off Function
Power Requirements
WARNING
• Use the specified adaptor (page 70). The use of other
adaptors may result in irreparable damage to both the
adaptor and the instrument.
1 Connect one end of the AC cable to the power
adaptor.
AC power adaptor
To prevent unnecessary power consumption, this
instrument features an Auto Power Off function that
automatically turns the power off if the instrument is
not operated for a specified period of time. The
amount of time that will elapse before the power is
automatically turned off is set by default to 30 minutes. To disable the Auto Power Off function, turn off
the power, then press the [ ] (Standby/On) switch to
turn on the power while holding down the lowest key.
2 Connect the power adaptor’s DC plug into the DC
IN jack on the instrument’s rear panel.
3 Plug the AC adaptor into an AC outlet.
CAUTION
Press and hold
• Unplug the AC Power Adaptor when not using the
instrument, or during electrical storms.
NOTE
• The setting time range can be changed in the Function display. For details, refer to the Reference Manual.
NOTE
• The data and settings are always backed up, and are maintained even when the power is turned off. For information on
the backup parameters, see page 53.
2
Connecting a Footswitch
3
AC outlet
AC power adaptor
The sustain function lets you produce a natural sustain
as you play by pressing an optional footswitch. Plug a
Yamaha FC4 or FC5 Footswitch into the SUSTAIN
jack and use it to switch sustain on and off.
NOTE
• Make sure that the footswitch plug is properly connected to
the SUSTAIN jack before turning on the power.
• Do not press the footswitch while turning the power on. Doing
this changes the recognized polarity of the footswitch, resulting in reversed footswitch operation.
10
Owner’s Manual
Setting Up
Connecting Headphones and
External Audio Equipment
Turning the Power On
Turn down the volume by turning the MASTER VOLUME control to the left and press the [ ] (Standby/
On) switch to turn on the power. While playing the
keyboard, adjust the volume level by using the MASTER VOLUME control. Press the [ ] (Standby/On)
switch again for a second to turn the power to standby.
You can connect the PHONES/OUTPUT jack to a set
of headphones, keyboard amplifier, stereo system,
powered speaker, tape recorder, or other line-level
audio device to send the instrument’s output signal to
that device.
CAUTION
The internal speakers are automatically shut off when
a plug is inserted into this jack. The PHONES/OUTPUT jack also functions as an external output.
• When using a power adaptor, even when the power is off, a
small amount of electricity is still being consumed by the
instrument. When you are not using the instrument for a
long time, make sure to unplug the AC power adaptor from
the wall AC outlet.
NOTE
• You can set the Master equalizer (EQ) which is provided to
give you the best possible sound when listening through different reproduction systems. The Master equalizer (EQ) can
be set in the Function display. For details, refer to the Reference Manual.
NOTICE
• Never attempt to turn the power off when a “Writing..” message is
shown in the display. Doing so can damage the data on the flash
memory and result in a loss of data.
CAUTION
• Avoid listening with the headphones at high volume for
long periods of time; doing so may not only result in ear
fatigue, it may be damaging to your hearing.
CAUTION
• To prevent damage to the speakers, set the volume of the
external devices at the minimum setting and turn power off
the devices before connecting them. Failure to observe
these precautions may result in electric shock or equipment damage. Also, be sure to set the volumes of all
devices at their minimum levels and gradually raise the volume controls while playing the instrument to set the
desired listening level.
Owner’s Manual
11
Setting Up
Changing the Display Language
This instrument allows you to select English or Japanese as the display language. The default display language is English, but if you switch to Japanese the
lyrics, file names and some messages will be displayed in Japanese where appropriate.
Adjusting the Display CONTRAST
control
Adjust the display CONTRAST control on the rear
panel of the instrument for optimum display legibility.
1 Press the [FUNCTION] button.
CAUTION
• Looking at the display for a long period of time in the dark
may cause eyestrain or damage to your eyesight. Make
sure to use the instrument with as much ambient light as
possible and also take adequate breaks and rest from use.
2 Press the CATEGORY [<] and [>] buttons repeatedly until the “Language” item appears.
The currently selected display language will appear
below the “Language” item.
Music Rest
Insert the music
rest into the slots
as shown.
Language item
The currently selected
language
3 Select a display language.
Using dial to select English or Japanese.
The language selection will be stored in the internal flash memory so that it is retained even when
the power is turned off.
4 Press the [EXIT] button to return to the Main display.
12
Owner’s Manual
Setting Up
Displays and Basic Operation
Main Display
The Main display, called up when the power is turned on, shows all of the current basic settings: Song, Style,
Voice.
It also includes a range of indicators that show the on/off status of a range of functions.
Transpose
Measure number
Octave
(page 20)
(page 43)
(page 20)
USB status
Appears when the USB flash
memory is connected (page 55).
A-B Repeat
Tempo
Appears when the Repeat
function is on for Song playback.
(page 39)
(page 34)
Harmony
(page 19)
Touch Response
(page 26)
Sustain
(page 19)
Music Database
(page 46)
Registration Memory /
Song or Style track
indication
Chord
Display
Registration Memory
bank status
(page 32)
(page 49)
Song / Style track status
(page 41)
Shows currently selected item:
REGIST., TR 1–8, TR 9–16
(page 49)
Main Voice (page 16)
Dual Voice (page 17)
Left Voice (page 17)
Style (page 29)
Song (page 35)
 To Return to the Main Display
Since the instrument has so many different displays, you may occasionally find yourself confused as to
which operation’s display is currently shown. In such a case, return to the Main display by pressing the
[EXIT] button.
Owner’s Manual
13
Setting Up
VOICE, STYLE, SONG, and MDB Select Displays
Press one of the category selection buttons such as VOICE, STYLE, SONG, or press the [MDB] button to call up
selection display for each. In each display, you can select an item as desired using the CATEGORY buttons or the
dial.
Previous category
Next category
Category
Item
 Select a Category
Use the CATEGORY [<] and [>] buttons to step in sequence through the categories.
 Select a Voice, Style, Song or MDB
Use the dial or the [-/NO]/[+/YES] buttons to select an item as desired. Press and hold either button to continuously increment or decrement the value in the corresponding direction.
Decrease
Increase
Press briefly to
decrement.
14
Owner’s Manual
Press briefly to
increment.
Setting Up
Function Display
In the Function display, you can make detailed settings for this instrument. The Function display appears when the
[FUNCTION] button is pressed. In the display you can use the CATEGORY [<] and [>] buttons to select 60 different function items. Press the CATEGORY button(s) as many times as necessary until the required function
appears, then use the dial or the [-/NO] and [+/YES] buttons to adjust the value of the function as required. To
recall the default value, press the [-/NO] and [+/YES] buttons simultaneously.
Function item
Value
All items which can be selected in the Function display are listed in the Panel Button Chart on page 66.
 Move the highlighted Position
In some Function displays, pressing the [EXECUTE] button will move the highlighted position from the current
one to the other one.
 Shortcut
You can jump directly to certain Function displays by holding the related button for longer than a second. The buttons are as follows:
• [FUNCTION] button ..............Scale
• [DEMO] button.......................Demo Group
• [ACMP] button .......................Chord Fingering
• [METRONOME] button.........Time Signature-Numerator
• [FREEZE] button....................Freeze Group Setting
• [HARMONY] button..............Harmony Type
• [TOUCH] button.....................Touch Sensitivity
• [DSP] button ...........................DSP Type
This can be particularly handy since such a large number of Functions are available.
Owner’s Manual
15
1
Voices – Playing the Keyboard –
In addition to piano, organ, and other standard keyboard instruments, this instrument
has a large range of realistic Voices—including guitar, bass, strings, sax, trumpet,
drums and percussion, sound effects, and a wide variety of other musical sounds.
Select and Play a Main Voice
In this operation, you’ll select a Main Voice and play it on the keyboard.
1
Select and press the desired Voice category button in the Voice
section.
The Main Voice selection display will appear. The currently selected category
name, Voice number and name will be highlighted.
NOTE
• To change the Voice category, press another category
button.
MAIN VOICE
selection display
CATEGORY name
Current selected
Voice
You can select the GM&XG category Voice by pressing the [PIANO] button
then CATEGORY [<] button to call up the GM&XG category.
2
Select the Voice you want to play.
Look at the highlighted Voice name and rotate the dial. The available Voices
will be selected and displayed in sequence. The Voice selected here becomes the
Main Voice.
3
Play the keyboard.
• The main Voice parameters
such as Volume can be set
in the Function display. For
details, refer to the Reference Manual.
Try selecting and playing a variety of Voices.
Press the [EXIT] button to return to the Main display.
16
NOTE
Owner’s Manual
1. Voices – Playing the Keyboard –
Playing Two Voices Simultaneously
Once you press the [DUAL] button to turn the Dual Voice on, a second voice will sound that will play in addition
to the Main Voice when you play the keyboard. The second voice is known as the “Dual Voice.”
NOTE
• The Dual Voice parameters
such as Voice Volume can
be set in the Function display. For details, refer to the
Reference Manual.
The button lights
when Dual is ON.
Two Voices will sound at the
same time.
Press the button again to turn the Dual Voice off.
 Selecting a Dual Voice
You can select any voice as a Dual Voice. Press and hold the [DUAL] button for longer than a second to call up the Dual Voice selection display, then select a Dual Voice
in the same way as selecting a Main Voice. After selecting, press the [EXIT] button
to return to the MAIN display.
Splitting the Keyboard and Playing the Left Voice with the Left Hand
Once you press the [LEFT] button to turn the Left Voice on, you can play different Voices to the left and right of
the keyboard “split point.” The Main and Dual voices can be played to the right of the split point, while the Voice
played to the left of the split point is known as the “Left Voice.”
NOTE
• The Left Voice parameters
such as Volume can be set
in the Function display. For
details, refer to the Reference Manual.
Split point
The button lights when
Left Voice is ON.
Left Voice
Main Voice and
Dual Voice
Press the button again to turn the Left Voice off.
 Selecting a Left Voice
You can select any voice as a Left Voice. Press and hold the [LEFT] button for longer than a second to call up the Left Voice selection display, then select a Left Voice
in the same way as selecting a Main Voice. After selecting, press the [EXIT] button
to return to the MAIN display.
Owner’s Manual
17
1. Voices – Playing the Keyboard –
Playing Drum Kits
Drum Kits are collections of drum and percussion instruments. When you select a violin or other normal
instrument—as a Main Voice, for example—all keys produce the sound of the same violin, only at different
pitches. If you select a Drum Kit as the Main Voice, however, each key produces the sound of a different
drum or percussion instrument.
1
Press the [DRUM KIT] button.
The “Drum Kit” category appears.
2
Rotate the dial and select the Drum Kit you want to play (001–025).
A good Drum Kit to start out with is 003, Standard Kit 1.
Drum Kit List
Voice
No.
001
002
003
004
005
006
007
3
Drum Kit name
Power Kit 1
Power Kit 2
Standard Kit 1
Standard Kit 2
Hit Kit
Jazz Kit
Brush Kit
Voice
No.
008
009
010
011
012
013
014
Drum Kit name
Room Kit
Rock Kit
Electro Kit
AnalogT8 Kit
AnalogT9 Kit
Break Kit
HipHop Kit
Voice
No.
015
016
017
018
019
020
021
Drum Kit name
Analog Kit
Dance Kit
Symphony Kit
Cuban Kit
PopLatin Kit
Arabic Kit
Arabic Kit 2
Play each key and enjoy the Drum Kit.
Voice
No.
022
023
024
025
Drum Kit name
Arabic Mixture Kit
Indian Kit
Chinese Kit
Chinese Mixture Kit
NOTE
• See the Drum Kit List in the
separate Data List.
ui
ca
Tr Mut
ia
ng e
l
Sh e M
u
ak
er te
C
Bo
ng
o
Co L
ng
a
H
O
pe
Ti
m
n
ba
le
Ag
L
og
o
L
M
ar
ac
as
G
ui
ro
Sh
C
o
la
ve rt
s
Sl
ap
Ca
st
an
et
St
ick
s
O
pe
n
R
im
Sh
Si
ot
de
St
ick
H
an
d
C
la
p
H
i-H
at
C
H
i-H los
ed
at
P
H
i-H eda
l
at
O
pe
n
C
ra
sh
Cy
R
m
id
b
e
Cy al
1
m
ba
Ta
l1
m
bo
Co urin
e
w
be
ll
Vi
br
as
la
p
h
us
Br
Br
us
h
Ta
p
Example: 003 Standard Kit 1
H
lic
k
h
C
h
us
q
us
Br
Br
Se
S
Ta wir
l
p
Sn Sw
ar irl
e
Sn Ro
ar ll
e
S
Ki oft
ck
Ki Sof
t
ck
Ti
gh
t
Ki
ck
Sn Sn
ar are
e
Fl
T
oo igh
r
t
Fl Tom
oo
rT L
om
Lo H
w
M To
id m
T
M om
id
L
To
H mH
C
ig
hi
h
n
R ese To
id
C m
e
Cy ym
Sp mb bal
la al C
C sh C up
ra
sh ym
Cy ba
R
id mb l
e
Cy al 2
m
ba
Co Bon l 2
ng go
a
H H
M
Co ute
n
Ti ga
m
L
ba
l
Ag e H
og
o
Sa
C H
m
ba ab
Sa W asa
m his
ba
tl
W eH
h
G istle
W uiro L
oo L
d on
W Blo g
oo ck
d
B H
C loc
ui
ca k L
Tr
O
ia
ng pe
n
le
Ji Op
ng en
le
B
Be ells
ll T
re
e
C3
18
Owner’s Manual
1. Voices – Playing the Keyboard –
Applying Effects to a Voice
You can apply effects to a Voice played on the keyboard by pressing the Voice Control buttons. To turn the effect
off, press the button again.
NOTE
• You can specify the Harmony type. For details, refer
to the Reference Manual.
The button lights when
DSP is ON.
Adding Harmony
This feature adds harmony notes as well as
tremolo or echo effects to
the Main Voice. A suitable Harmony type is
automatically selected
when you select a Main
Voice.
Adding Sustain
This function adds sustain to the keyboard
voices. Use it when you
want to add sustain to the
voices at all times, regardless of footswitch operation. The sustain function
does not affect the Left
Voice.
Adding DSP
A huge variety of DSP
effects are available for
applying to the Main,
Dual and Left Voices. A
suitable DSP type is
automatically selected
when you select a Main
Voice.
NOTE
• For some Voices, sustain
may not be audibly affected
when the Sustain is turned
on.
NOTE
• You can specify the DSP
type. For details, refer to the
Reference Manual.
You can see the on/off status for the Harmony and Sustain in the Main display.
Appears when Sustain is on
Appears when Harmony is on
How to Play Each Harmony Type
The Harmony behaves differently depending on the type. Check the current Harmony Type on the display by holding the [HARMONY] button for longer than a second.
Harmony types 01 to 10, 13
Press the right-hand keys while playing chords in the
Auto Accompaniment range of the keyboard when the
Auto Accompaniment is on (page 29).
Harmony types 15 to 18 (Echo)
Hold the keys.
Harmony types 19 to 22 (Tremolo)
Play the keys.
Harmony types 23 to 26 (Trill)
Hold down two keys.
Reverb and Chorus
The other effects provided are Reverb and Chorus. Reverb lets you play with a rich
concert hall type ambience, and Chorus effect creates a thick sound that is similar to
many of the same voices being played in unison. A suitable Reverb type and Chorus
type are automatically selected when you select a Style or Song.
NOTE
• You can specify the Reverb
type and Chorus type. For
details, refer to the Reference Manual.
Owner’s Manual
19
1. Voices – Playing the Keyboard –
Changing the Pitch of the Instrument
Using the Pitch Bend Wheel
The Pitch Bend wheel can be used to add smooth pitch variations to notes you play
on the keyboard.
NOTE
• The pitch bend range can
be changed by setting the
“PB Range” parameter on
the Function display. For
details, refer to the Reference Manual.
Adjusting the pitch in semitones (Transpose)
The overall pitch of the instrument can be shifted up or down in semitones by pressing the TRANSPOSE [+]/[-] buttons. The value is shown in the display, indicating
the amount of transposition over or below the normal value between -12 and +12 (a
maximum of one octave.) The setting can be reset to the initial default value “00” by
pressing the [+] and [-] buttons simultaneously.
NOTE
• This setting does not affect
the Drum Kit Voices.
Changing the Pitch in Octaves
You can change the playing pitch of the Main and Dual Voices in octave intervals by
pressing the UPPER OCTAVE [-]/[+]buttons. The newly changed value is shown in
the display between -1 and +1. The setting can be reset to the initial default value “0”
by pressing the [-] and [+] buttons simultaneously.
20
Owner’s Manual
NOTE
• When a Drum Kit is selected,
each percussion Voice
assigned to the keyboard is
shifted in location but not
pitch.
1. Voices – Playing the Keyboard –
Fine-tuning the Pitch of the Entire Instrument
You can fine-tune the pitch of the entire instrument by a maximum of 1 semitone—useful when you play this instrument along with other instruments or CD
music.
1
Press the [FUNCTION] button to call up the Function display.
2
Press the CATEGORY [<] and [>] buttons as many times as necessary to call up “Tuning.”
NOTE
• This setting does not affect
the Drum Kit Voices.
Tuning
3
Use the dial to set the tuning value between 415.3–466.2Hz as
desired.
The range is 415.3–466.2, equivalent to -1semitone – +1semitone.
NOTE
• Press the [EXIT] button to
return to the Main display.
Value
Owner’s Manual
21
1. Voices – Playing the Keyboard –
Scale Tuning
By default, this keyboard scale is set to Equal Temperament—the same tuning as with any acoustic piano. However, the setting can be changed to any other scale according to the music genre or music style you want to play.
Selecting a Scale
You can select various scales for playing in custom tunings for specific historical
periods or music genres.
Press and hold the [FUNCTION] button for longer than a second to call up the Scale
select display, then rotate the dial to select the desired Scale. The setting can be reset
to the initial default value by pressing the [-/NO] and [+/YES] buttons simultaneously.
NOTE
• This setting does not affect
the Drum Kit Voices.
NOTE
• Press the [EXIT] button to
return to the Main display.
Hold for longer
than a second
Preset Scale types
22
EQUAL
The pitch range of each octave is divided equally into twelve
parts, with each half-step evenly spaced in pitch. This is the most
commonly used tuning in music today.
PURE MAJOR,
PURE MINOR
These tunings preserve the pure mathematical intervals of each
scale, especially for triad chords (root, third, fifth). You can hear
this best in actual vocal harmonies—such as choirs and a cappella singing.
PYTHAGOREAN
This scale was devised by the famous Greek philosopher and is
created from a series of perfect fifths, which are collapsed into a
single octave. The 3rd in this tuning are slightly unstable, but the
4th and 5th are beautiful and suitable for some leads.
MEAN-TONE
This scale was created as an improvement on the Pythagorean
scale, by making the major third interval more “in tune.” It was
especially popular from the 16th century to the 18th century.
Handel, among others, used this scale.
WERCKMEISTER,
KIRNBERGER
This composite scale combines the Werckmeister and Kirnberger systems, which were themselves improvements on the
mean-tone and Pythagorean scales. The main feature of this
scale is that each key has its own unique character.
The scale was used extensively during the time of Bach and
Beethoven, and even now it is often used when performing
period music on the harpsichord.
ARABIC1,
ARABIC2
Use these tunings when playing Arabic music.
Owner’s Manual
NOTE
• “(Edited)” will appear in the
display if you have created
your original scale using the
“Scale Tune” function (page
23).
1. Voices – Playing the Keyboard –
Setting the Base Note for Each Scale
When the base note is changed, the pitch of the keyboard is transposed, yet the original pitch relationship between the notes is maintained. Please make sure to specify
the appropriate Base Note, if you select a scale other than Equal Temperament, or
create an original scale via Scale Tune function.
Press the [FUNCTION] button then use the CATEGORY [<] and [>]
buttons as many times as necessary to select the “Base Note.” Use
the dial to select the Base Note from C, C#, D, Eb, E, F, F#, G, Ab, A,
Bb, B.
The setting can be reset to the initial default value by pressing the [-/NO] and [+/
YES] buttons simultaneously.
Tuning Each Note to Create an Original Scale
You can tune the individual notes in cents to create your original scale. The term
“cent” refers to one hundredth of a semitone (i.e., 100 cents = 1 semitone). After
selecting the appropriate Base Note, follow the instructions below.
1
Press the [FUNCTION] button then use the CATEGORY [<] and
[>] buttons as many times as necessary to select “Scale Tune.”
2
Use the dial to select the note to be tuned, then press the [EXECUTE] button.
The tuning value is highlighted, allowing you to tune the note.
Note
NOTE
• The settings here are linked
with the Base Note. For
example, if the Base Note for
the original scale is changed
from C to F, the tuning values
for keys C–B are shifted to
F–E.
Tuning value (cent)
3
Use the dial to tune the note, then press the [EXECUTE] button.
The tuning range is between -64 – +63. The setting can be reset to the initial
default value by pressing the [-/NO] and [+/YES] buttons simultaneously.
Owner’s Manual
23
1. Voices – Playing the Keyboard –
4
5
Repeat steps 2–3 to tune any of the remaining notes.
Memorize the settings here to the Registration Memory as desired
(page 50).
Selecting a Part for Scale Tune
With the initial settings, Scale Tune is applied only to the Main/Dual Voices, not to
the Left Voice and Style playback. If you want to apply this setting to the Left Voice
or Style playback as well as the Main/Dual Voices, follow the instructions below.
1
Press and hold the [FUNCTION] button for longer than a second
to call up the Scale select display.
2
Use the CATEGORY [>] button as many times as necessary to
select “Part Select.”
The Part and ON/OFF status are shown.
3
Use the dial to select the part, then press the [EXECUTE] button.
Select the desired part from Main/Dual Voices, Left Voice, and Style. After that,
press the [EXECUTE] button so that the highlighted area will move to the ON/
OFF status.
Part
24
Owner’s Manual
NOTE
• Press the [EXIT] button to
return to the Main display.
1. Voices – Playing the Keyboard –
4
Rotate the dial to select ON (apply) or OFF (not apply), then press
the [EXECUTE] button.
The highlighted area will return to Part Select again. Repeat steps 3–4 as
desired.
ON/OFF status
5
Memorize the settings here to the Registration Memory as desired
(page 50).
Applying Scale Tune MIDI Messages to the Keyboard
Performance
You can apply Scale Tune MIDI messages received from an external MIDI device to
the keyboard performance. The default setting applies MIDI messages to Song playback; however, you can change it to the keyboard performance by following the
instructions below.
1
Press and hold the [FUNCTION] button for longer than a second
to call up the Scale select display.
2
Use the CATEGORY [>] button as many times as necessary to
select “External Scale Tune.”
Owner’s Manual
25
1. Voices – Playing the Keyboard –
3
Rotate the dial to select ON (KEYBOARD).
With the default setting of “OFF,” MIDI messages are applied to Song channels
1–16, not to the keyboard performance.
If you set this to “ON (KEYBOARD),” the MIDI messages are applied to the
keyboard performance as follows: Channel 1 = Main Voice, Channel 2 = Dual
Voice, and Channel 3 = Left Voice; the other channels are not affected.
ON/OFF status
Touch Response ON/OFF
The keyboard of this instrument is equipped with a Touch Response feature that lets
you dynamically and expressively control the level of the voices with your playing
strength. However, you may want to produce the same volume no matter how
strongly or softly you play the keyboard, depending on the Voice. In this case, press
the [TOUCH] button to turn this function off. You can see the on/off status for Touch
Response in the Main display.
NOTE
• Touch Sensitivity, or how the
sound volume responds to
the playing strength, can be
set in the Function display.
For details, refer to the Reference Manual.
Appears when Touch Response is on
26
Owner’s Manual
1. Voices – Playing the Keyboard –
Using the Metronome
Playing the Metronome
The metronome provides a click sound, giving you an accurate tempo guide when
you practice, or letting you hear and check how a specific tempo sounds. Press the
[METRONOME] button to start the metronome. To stop the metronome, press the
[METRONOME] button again.
Time Signature
Beat Number
Setting the Time Signature and Tempo
Normally, the metronome time signature and tempo will be determined by the current Style or Song. The current value is shown in the upper left corner of the Main
display. If you want to change the time signature or tempo, follow the instructions
below.
1
Press and hold the [METRONOME] button for longer than a second.
The currently selected time signature is shown. In this example we’ll set up a 3/
4 time signature.
Hold for longer
than a second
Numerator
(Number of beats
per measure)
Denominator
(the note value or
length of one beat)
You can set the Numerator in this display.
2
Use the dial to select the number of beats per measure.
The Bell will sound on the first beat of each measure while a metronome “click”
will sound on all others. You can set the time signature from 01 to 60. Select “3”
for this example.
NOTE
• If you start playback of the
Style or Song, the metronome time signature is
changed to that of the Style
or Song that is playing.
Owner’s Manual
27
1. Voices – Playing the Keyboard –
3
Press the CATEGORY [>] button once to call up the Time Signature Denominator display.
3
4
Use the dial to select a beat length.
Select the required length for each beat: 2, 4, 8, or 16 (half note, quarter note,
eighth note, or 16th note). For this example, select 4. The time signature should
now be set to 3/4.
4
Press the [METRONOME] button to confirm the settings.
5
Use the TEMPO [+] and [-] buttons to set the tempo.
Or press any of the TEMPO buttons once to call up the Tempo setting in the display, then use the dial to set the value.
28
Owner’s Manual
NOTE
• Other metronome settings
such as Volume or Bell
sound can be set in the
Function display.
2
Styles – Playing Rhythm and Accompaniment –
This instrument includes the Auto Accompaniment feature that plays appropriate
“Styles” (rhythm + bass + chord accompaniment) when you play left-hand chords. You
can select from a huge variety of Styles covering a wide range of musical genres.
Select and Play a Style
1
Select and press the desired Style category button.
The Style selection display appears.
The current category name, Style number and name will be highlighted.
NOTE
• In addition the Preset Styles,
you can create your own
Style. For details, refer to the
“Style Creator” chapter of
the Reference Manual.
Style selection
display
The currently
selected category
The currently
selected Style
2
Select the Style you want to play.
Look at the highlighted Style name and rotate the dial. The available Styles will
be selected and displayed in sequence. See the Style list in the separate Data
List.
3
Turn the Auto Accompaniment on.
Press the [ACMP] button. Pressing this button again will turn the Auto Accompaniment off.
NOTE
• The [EXPANSION/USER]
button is used for calling up
your original Styles created
with the Style Creator, or
Styles loaded/installed from
a USB flash memory (pages
59 and 61.) For details about
the Style Creator, refer to the
Reference Manual.
The [ACMP] button lights when the
Auto Accompaniment is turned on.
Owner’s Manual
29
2. Styles – Playing Rhythm and Accompaniment –
NOTE
When the Auto Accompaniment is on...
The area of the keyboard to the left of the split point (F#2) becomes the Auto
Accompaniment range and is used only for specifying the Accompaniment
chords.
• The Split Point can be
changed in the Function display. For details, refer to the
Reference Manual.
Split Point (F#2)
Auto Accompaniment range
4
Press the [AUTO FILL IN] button to turn Auto Fill In on.
The initial setting is “on.”
The button lights when Auto Fill In is ON.
5
Press the [SYNC START] button to turn Synchro Start on.
• You can start the Style by
simply tapping the [TEMPO/
TAP] button at the required
tempo—four times for time
signatures in 4, and three
times for time signatures in
3. You can change the
tempo during style playback
by pressing the button just
twice.
The [SYNC START] button lights indicating
Synchro Start is engaged.
Synchro Start
When Synchro Start is on, you can start the Style by playing any key in the
accompaniment range of the keyboard. To cancel or disable Sync Start, press the
button again.
6
30
NOTE
Press one of the MAIN VARIATION [A]–[D] buttons as desired.
The selected Main Variation button flashes.
Owner’s Manual
• You can also press the
[START/STOP] button to
begin the rhythm of the
selected Style. The bass
and chords will begin playing as soon as you play a
key in the Auto Accompaniment range of the keyboard.
2. Styles – Playing Rhythm and Accompaniment –
7
Press one of the INTRO [I]–[III] buttons.
The selected Intro button lights.
8
Play a chord in the Auto Accompaniment range to start the Intro
section.
Try playing a C major chord. (See “Playing Auto Accompaniment Chords” on
page 32.)
NOTE
• The Baroque Air Style in the
MOVIE & SHOW category
does not have a Rhythm
part, and so does not produce any rhythm sound.
Split Point
Auto Accompaniment range
Chord
When the playback of the intro is finished, it automatically leads into the Main
Variations.
9
Press one of the MAIN VARIATION [A]–[D] buttons.
The Main Variation corresponding to the pressed button plays following an
automatic fill-in.
10
Press one of the ENDING/rit. [I]–[III] buttons.
NOTE
• The Style Volume can be
adjusted in the Function display. For details, refer to the
Reference Manual.
This switches to the Ending section. When the Ending is finished, the Style
playback stops automatically. You can have the Ending gradually slow down
(ritardando) by pressing the same ENDING/rit. button again while the Ending is
playing back.
Owner’s Manual
31
2. Styles – Playing Rhythm and Accompaniment –
Playing Auto Accompaniment Chords
For users who are unfamiliar with chords, this handy chart features common chords for your quick reference.
Chords recognized by this instrument are described in the Reference Manual on the website.
 Indicates the root note.
Major
Minor
Seventh
Minor Seventh
Major Seventh
C
Cm
C7
Cm7
CM 7
D
Dm
D7
Dm7
DM 7
E
Em
E7
Em7
EM7
C
F
Fm
F7
Fm7
FM7
G
Gm
G7
Gm7
GM7
A
Am
A7
Am7
AM 7
B
Bm
B7
Bm 7
BM 7
Easy Chords
This method lets you easily play chords in the accompaniment range of the keyboard using only one, two, or three
fingers.
For root “C”
C
To play a major chord
Press the root note () of
the chord.
Cm
To play a minor chord
Press the root note together
with the nearest black key to
the left of it.
C7
To play a seventh chord
Press the root note together
with the nearest white key to
the left of it.
Cm 7
To play a minor seventh chord
Press the root note together with
the nearest white and black keys
to the left of it (three keys altogether).
Changing the Chord Fingering Type
You can select the different chord fingering type such as normal chords played anywhere on the keyboard will be detected
in it. Chord fingering type can be changed in the Function display. For details, refer to the Reference Manual.
32
Owner’s Manual
2. Styles – Playing Rhythm and Accompaniment –
Synchro Stop
When this function is selected, the accompaniment Style will only play while you
are holding down chords in the Accompaniment range of the keyboard. Style playback will stop when you release the keys. To turn the function on, press the [SYNC
STOP] button. To turn the function off, press the button again.
The Style will play
while you are playing
the keys
NOTE
• This function cannot be
used if the “FullKeyboard” is
selected from the “Chord
Fingering” parameter on the
Function display.
Style playback will stop
when you release the
keys
Select and Play a Style from USB Flash Memory
Styles on a USB flash memory connected to the USB TO DEVICE terminal can be
directly selected and played. Press the [USB] button in the Style mode (page 35) and
the name of the currently selected Style on the USB flash memory will appear in the
display. Rotate the dial to select the desired Style, then play the Style by following
the instructions on pages 29–31
NOTE
• Before using a USB flash
memory, be sure to read
“Precautions when using the
[USB TO DEVICE] terminal”
on page 54.
If this button is lit, press
the button to turn off.
The Style files must be saved either in the USB flash memory’s root directory or a
first-level/second-level/third-level folder in the root directory. The directory can be
moved using the CATEGORY [<]/[>] buttons.
Owner’s Manual
33
2. Styles – Playing Rhythm and Accompaniment –
Changing the Tempo
You can use the TEMPO [+] and [-] buttons to adjust the playback tempo as required before or during playback.
While the TEMPO pop-up is shown on the display, you can also use the dial to adjust the value.
Pressing the TEMPO [+]/[-] buttons simultaneously resets the tempo to the default value.
or
The Tempo can also be changed during playback by tapping the [TAP TEMPO] button twice at the desired tempo.
One Touch Setting
With all the choices available on the instrument, sometimes selecting the ideal Voice to play with a Song or Style
can be confusing. The One Touch Setting feature automatically selects four ideally matched Voices for the Style
you’ve selected.
Select the desired Style (See page 29), then press one of the ONE TOUCH SETTING [1]–[4] buttons to call up
the appropriate panel settings. As soon as you play a chord with your left hand, the selected Style starts. Try
selecting other ONE TOUCH SETTING [1]–[4] buttons and listen to the results.
Variation Change and OTS (OTS LINK)
When one of the Main Variations [A]–[D] changes to another Main Variation while
OTS LINK is on, the OTS number (1–4) automatically changes according to the
selected variation number.
Press the [OTS LINK] button to turn on the OTS link.
34
Owner’s Manual
3
Using Songs
With this instrument, the term “Song” refers to the data that makes up a piece of
music.
In this section we’ll learn how to select and play a Song.
Selecting and Listening to a Song
1
Press the desired Song category button.
The Song selection display will appear. The currently selected Song number and
name will be highlighted.
Song Selection display
Currently selected Song
[PRESET] : Nine preset Songs are available here.
[USER] : This contains your recorded Songs and Songs loaded from a USB
flash memory or transferred from a computer. For details about how to load
Songs, refer to page 59.
[USB] : This contains Songs on a USB flash memory connected to the USB TO
DEVICE terminal. For details, refer to page 37.
Song mode and Style mode
(Lit)
Song mode
(Unlit)
Style mode
The instrument has two modes: Song and Style. In the Song mode, you can play, record and edit Songs, while
the Style mode lets you play and create Styles. To alternate between the two modes, press the [SONG MODE]
button.
The Song mode has the following limitations:
• Some buttons in the Style Control section become Song related buttons, and other buttons are disabled.
• The [ACMP] button cannot be turned on.
• Styles cannot be played.
2
Select the desired Song.
Use the dial to call up the Songs in order within the category selected in step 1.
Owner’s Manual
35
3. Using Songs
PRESET
USER
USB
Built-in Songs
001 Guitar Voice demo (Original)
002 Dance Voice demo (Original)
003 Drums Voice demo (Original)
004 Amazing Grace (Traditional)
005 Annie Laurie (Traditional)
006 Latin (Original)
007 Arabic (Original)
008 Bhangra (Original)
009 Wu Lin Hun (Original)
001–005 User Songs (Songs you record yourself)
006–
Songs loaded from a USB flash memory/transferred from a computer
Songs in a USB flash memory connected to the instrument
* Some of the preset songs have been edited for length or arrangement, and may not be exactly the same as the original.
* Preset Song 004 is displayed as “Score demo”, and preset Song 005 as “Lyric demo” in the display.
3
Listen to the Song.
Press the [
] button to begin playback of the selected Song.
You can stop playback at any time by pressing the [
] button again.
NOTE
• Press the [EXIT] button to
return to the Main display.
Song start
You can turn individual tracks of the Song on and off. For details, refer to the
Reference Manual.
Changing the Tempo
This is the same as changing the Style tempo. For details, refer to page 34.
Fast Forward, Fast Reverse, and Pause
These are similar to the transport controls on a CD player, letting you fast forward [f], rewind [r], and pause
[o] playback of the Song.
NOTE
• These buttons cannot be
used during Song playback
by using the [DEMO] button.
REW
Press and hold the fast
reverse button to rapidly
return to an earlier point
in the Song.
36
Owner’s Manual
FF
Press and hold the fast
forward button to rapidly skip ahead to a
later point in the Song.
PAUSE
Press the pause button to pause playback. Press this button again to resume
playback from the point at which it was
stopped.
3. Using Songs
Listening to the Demo Song
This instrument includes a Demonstration Song, showcasing the wide variety of the Preset Voices.
Press the [DEMO] button to start the Demo.
The Demo displays appear in the display.
The Demo Song will restart when playback reaches the end.
You can stop playback at any time by pressing the [DEMO] or [
] button.
You can change the repeat playback target from Demo Song to other Songs such
as Preset Songs. Press and hold the [DEMO] button for longer than a second to
call up the “Demo Group” selection display, and use the dial to select a repeat
playback group from the table below. Press the [DEMO] button to start sequential playback of the Songs in the selected group.
Demo
Demo Song
Preset
All Preset songs
User
All User songs
Download
All Songs transferred from a computer
USB
All Songs on a USB flash memory connected to the instrument.
Select and Play a Song from USB Flash Memory
Songs on a USB flash memory connected to the USB TO DEVICE terminal can be
directly selected and played. Press the [USB] button in the Song mode (page 35) and
the name of the currently selected Song on the USB flash memory will appear in the
display. Rotate the dial to select the desired Song, then press the [
] button to
start playback.
NOTE
• Before using a USB flash
memory, be sure to read
“Precautions when using the
[USB TO DEVICE] terminal”
on page 54.
If this button is unlit,
press it to turn it on.
The Song files must be saved either in the USB flash memory’s root directory or a
first-level/second-level/third-level folder in the root directory. The directory can be
moved using the CATEGORY [<]/[>] buttons.
Owner’s Manual
37
3. Using Songs
Displaying the Song Score
This instrument is capable of displaying the scores (notation) of Songs, including the preset Songs as well as
Songs loaded from a USB flash memory or computer.
1
Select a Song.
Follow steps 1 and 2 on page 35.
2
Press the [SCORE] button and a single-staff score will appear.
There are two types of score display: single-staff and double-staff.
These are alternately selected each time the [SCORE] button is pressed.
NOTE
Single-staff
Marker
Melody score
Chord
(Only when
included)
Lyric
(Only when
included)
• When there are many lyrics
in a Song, they may be displayed in two rows a measure.
• Some lyrics or chords may
be abbreviated if the
selected Song has a lot of
lyrics.
• Small notes that are hard to
read may be easier to read
after you change the quantize setting in the Function
display. For details, refer to
the Reference Manual.
NOTE
• No lyrics and chords are
shown in the double staff
display.
During playback, the marker will indicate the current position in the score.
Displaying the Lyrics
If a Song contains lyric data, the lyrics can be shown on the display.
1
Select a Song.
Follow steps 1 and 2 of the procedure described on page 35.
Here, select Preset Song 004 or 005.
2
Press the [LYRICS] button.
The title, lyricist, and composer of the Song will appear on the display.
NOTE
• Songs downloaded from the
Internet or commercially
available Song files, including XF format files (page 6),
are compatible with the lyrics display features as long
as they are standard MIDI
file format files containing
lyric data. Lyrics display may
not be possible with some
files.
NOTE
Song title, Lyricist,
Composer
During playback, the lyrics and chords are shown in succession on the display.
38
Owner’s Manual
• If the lyrics display shows
garbled characters, try
changing the display language (page 12).
3. Using Songs
A-B Repeat
You can specify a section of a Song—“A” is the start point and “B” is the end point—for repeat playback. The AB Repeat function is also very convenient for practicing when used along with the score display features
of the instrument.
A
1
B
Play the Song (page 35) and press the [
] button at the
beginning of the section you want to repeat (the “A” point).
Point A
2
Press the [
] button again at the end of the section you want
to repeat (the “B” point).
Point B
3
After a lead-in count, the specified A-B section of the Song will
now play repeatedly.
You can cancel A-B repeat playback at any time by pressing the [
] button.
NOTE
• The current measure number is shown in the display
during playback.
• If you want to set the start
point “A” at the very beginning of the Song press the
[
] button before starting playback of the Song.
Owner’s Manual
39
4
Recording Your Own Performance
You can record up to five of your own performances and save them as User Songs 001
through 005. These Songs can be played in the same manner as the Preset Songs.
Once your performances have been saved as User Songs, they can be saved to a USB
storage device (page 58).
 Recordable data
Melody performance and Style playback with chord or section changes can be
recorded to any 16 tracks of the Song.
 Recording methods
• Quick Recording ....... Immediately start recording with Style playback by pressing
the [REC] button. This method automatically sets tracks 1–
3 as melody parts and tracks 9–16 as Style parts. This is
especially convenient and easy when recording a new Song.
• Multi Recording ........ Specify the Song number and the parts for the tracks and
then start recording (page 41). This is useful when you want
to record data to each track independently, one by one.
NOTE
• Up to approximately 30,000
notes can be recorded, if
you record only to the melody tracks.
Quick Recording Procedure
1
Enter the Song mode (page 35), then press the [REC] button.
The [REC] button lamp lights, and the User Song number for recording will be
selected automatically.
User Song
NOTICE
• If all User Songs contain
recorded data, User Song
001 will automatically be
selected. If you record your
performance to a Song that
contains data, the previous
data will be erased by the
new data.
NOTE
Recording track
Performance parts are as follows:
Tracks [9]–[16] will be set for Style playback and the Record Ready mode is
enabled automatically.
Recording track
Part recorded to each track
Track 1
Main Voice performance
Track 2
Left Voice performance
Track 3
Dual Voice performance
Tracks 9–16
Style playback with chord/section changes
To cancel recording, press the [REC] button or [EXIT] button. (The [REC] button lamp turns off.)
40
Owner’s Manual
• You can manually select the
recorded user Song number if you select it before
pressing the [REC] button.
4. Recording Your Own Performance
2
3
Play the keyboard to start recording.
Stop recording by pressing the [
] or [REC] button.
or
4
Press the [+/YES] button to save the recorded Song.
When recording is stopped, a message asking if you want to save the Song will
appear. Press the [+/YES] button to save the Song, or the [-/NO] button if you
don’t want to save. If the [+/YES] button is pressed, the Song will be saved as a
MIDI file to the User Song selected in step 1.
Track numbers containing recorded data are indicated with framed rectangles.
NOTICE
• Never attempt to turn the
power off when a “Writing!” message is shown in
the display. Doing so will
result in a loss of the
recorded data.
NOTE
No track number ..... No data.
Track number without frame ..... Track contains data but is muted.
• A message asking if you
want to save the Song
appears again when you
select a different Song without saving. To save the
Song, press the [+/YES] button; to cancel, press the [-/
NO] button.
Track number with frame ...... Track contains data and is not muted.
5
Press the [
] button to play back the recorded Song.
Multi-track Recording Procedure
1
Press the [USER] button, then use the dial to select the desired
User Song number (001–005) for recording.
2
Press the [EXIT] button to return to the Main display, then assign
the Part (Style, Main, Dual and Left) to each recording track.
Owner’s Manual
41
4. Recording Your Own Performance
Assigning the Style Part
If you want to record the Style playback, hold the [REC] button then immediately press the [ACMP] button. On the panel, the [REC] and [ACMP] buttons
will light and the [START/STOP] button will flash, indicating that Record
Ready mode is enabled with the Auto Accompaniment on. On the display, the
REC indication will be highlighted, indicating that the Style Part will be
assigned to Tracks 9–16 for recording.
NOTICE
• If you assign the Part to a
Track containing data, the
Recording operation will
erase the previous data.
NOTE
• The [ACMP] button on/off
cannot be changed after the
Recording starts.
Press and hold
Immediately
press
ACMP (Style Part) is set to Record Ready mode.
Execute the same operation again to cancel this status.
Assigning the Melody Part (MAIN, DUAL and LEFT)
When the [ACMP] button is turned on:
Hold the [REC] button then immediately press one of the SONG Track [1]–[8]
buttons to call up the PART ASSIGN display. While continuing to hold the
[REC] button, repeatedly press the same Track button. The Track box indication
is alternated as follows: MAIN  DUAL  LEFT  (empty)  MAIN  ... .
Here, assign the MAIN part to the pressed Track.
Press and hold
Immediately
press
The MAIN part is assigned to the Track 1.
Execute the same operation to assign the MAIN, DUAL, and LEFT parts to the
different Tracks respectively.
When the [ACMP] button is turned off:
On the Main display, press the [REGIST/PART [MIXER]] button until your
desired Track group (“TR1-8” or “TR9-16”) is highlighted in the bottom right
corner of the display.
After that, execute the same operation as that of “When the [ACMP] button is
turned on:” described above.
42
Owner’s Manual
NOTE
• The Part can be assigned
only to a single Track.
4. Recording Your Own Performance
3
Play the keyboard to start recording.
You can also start recording by pressing the [
] button to play only the
rhythm.
When recording is started, the display automatically returns to the Main display,
showing the current measure number.
Current measure number
NOTE
• When Song memory
becomes full, a message
appears in the display and
recording will be stopped. In
this case, delete any unnecessary Song data by using
Song clear (page 44) or
track clear (page 45) then
start recording again.
Start
recording
4
Stop recording by pressing the [
] or [REC] button.
or
NOTE
• If you press one of the ENDING/rit. [I]–[III] buttons while
recording the ACMP track,
recording will stop as soon
as the Ending reaches to the
end.
When recording stops, the current measure number will return to 001 and the
recorded track numbers in the display will be shown in a box border. The corresponding track button will light up in green. A message prompting you to confirm saving of the data will appear.
5
Press the [+/YES] button to save the recorded Song.
Press the [+/YES] button to save the song, or the [-/NO] button if you don’t
want to save the song. If the [+/YES] button is pressed, the song will be saved as
a MIDI file to the User Song selected in step 1.
To Record Other Tracks.
Repeat steps 2 through 5 to record any of the remaining tracks.
You can listen to the previously recorded tracks while recording. Previously
recorded track numbers are shown in a box border. You can also mute previously recorded tracks (the muted tracks will not appear in the display) by pressing the appropriate [1/9]–[8/16] buttons while recording new tracks.
NOTICE
• Never attempt to turn the
power off when a “Writing!” message is shown in
the display. Doing so will
result in a loss of the
recorded data.
NOTE
• A message asking if you
want to save the Song
appears again if you select a
different Song without saving your Song. To save the
Song, press the [+/YES] button; to cancel, press the [-/
NO] button.
Redo the Recording
Simply select the track you want to re-record for recording in the normal way.
The newly recorded material will overwrite the previous data.
6
Press the [
] button to play back the recorded Song.
If you want to save the Song to a USB flash Memory as backup, refer to
page 58.
NOTE
• The Style number, Style volume and Time signature are
recorded only at the top of
the Song. These cannot be
recorded at the middle of
the Song.
Owner’s Manual
43
4. Recording Your Own Performance
Song Clear—Deleting User Songs
NOTE
This function clears an entire user Song (all tracks).
1
Press the [USER] button, then rotate the dial to select the user
Song (001 to 005) you want to clear.
Press the [EXIT] button to return to the Main display.
2
While holding the TRACK [8/16] button, press and hold the TRACK
[1/9] button for longer than a second.
Hold for longer
than a second
Press and hold
A confirmation message will appear on the display. Press [-/NO] to cancel the
Song Clear operation. If the message doesn’t appear, press the [REGIST/
PART[MIXER]] button to call up “TR 1-8” or “TR 9-16,” then try step 2 again.
3
Press the [+/YES] button to clear the Song.
The clear-in-progress message will appear briefly on the display while the Song
is being cleared.
Songs can also be cleared in the following way.
1
2
3
4
Press the [FILE MENU] button.
Press the category [<] and [>]buttons until “User Delete” appears.
Rotate the dial to select a Song.
Press the [EXECUTE] button.
A confirmation message will appear in the display.
5 Press the [+/YES] button to clear the Song.
44
Owner’s Manual
• If you want to clear a specified track, refer to the Track
Clear operation on page 45.
4. Recording Your Own Performance
Track Clear—Deleting a Specified Track From a User Song
This function lets you delete a specified track from a User Song.
1
Press the [USER] button and rotate the dial to select the desired
Song (001 to 005), then press the [EXIT] button to return to the
Main display.
2
Press the [REGIST/PART [MIXER]] button a few times to call up the
desired item, “TR 1-8” or “TR 9-16.”
3
Press and hold the desired track button ([1/9] to [8/16]) for longer
than a second.
Hold for longer than a second.
A confirmation message will appear on the display. Press [-/NO] to cancel the
Track Clear operation.
4
Press the [+/YES] button to clear the track.
The clear-in-progress message will appear briefly on the display while the track
is being cleared.
Owner’s Manual
45
5
Playing with the Music Database
If you want to play music in your favorite Style, but you’re not sure how to select the
best Voice and Style for the type of music you want to play, simply select the appropriate Style from the Music Database. The panel settings will automatically be adjusted
for the ideal combination of sounds and Style!
1
Press the [MDB] button.
The music database selection display will appear.
The currently selected category name, MDB number and name will be highlighted.
2
Select the Music Database which matches the music style or type
you want to play.
Referring to the Music Database List in the separate Data List, use the dial to
select a music database. Select one that matches the image of the song you
intend to play.
NOTE
3
Play the chords with your left hand and the melody with your right.
The Style will start playing when you play a left-hand chord to the left of the
split point (page 30). Refer to page 32 for information about playing chords.
NOTE
Split point
4
46
Press the [
Owner’s Manual
] button to stop playback.
• Music Database (MDB) files
on or loaded from a USB
flash memory connected to
the instrument can be
selected and used in the
same way as the internal
Music Databases. File load
instructions are provided on
page 59.
• You can check the assigned
Voice and Style at this point
by pressing the [EXIT] button to return to the Main display.
6
Mixer
This instrument has a Mixer feature that lets you control on/off settings for each track,
or adjust the Volume, Pan, Reverb Level and Chorus Level for each track during Song
or Style playback. By editing these parameters, you can change the feeling of the Song
or Style. Tracks [1]–[16] can be set for Song playback, and [9]–[16] for Style.
1
2
Select the Style or Song.
Press and hold the [REGIST/PART [MIXER]] button for longer than
a second so that the Mixer display appears.
Parameter
ON/OFF status and the
parameter value for each track
Current track
number
Value
Current track and its value are highlighted on the display.
In this example, Track 1 is selected, set to ON, and its volume is set to 110.
3
When in the Song mode, press the [REGIST/PART [MIXER]] button
to select the desired track group, 1–8 or 9–16.
The button toggles between tracks 1–8 and 9– 16.
In the Style mode, tracks 9–16 are selected automatically.
When track
1–8 is selected
When track 9–16 is
selected
4
Select the desired Track by pressing the corresponding button.
5
Set the ON/OFF status of the selected track.
Pressing the Track button pressed in step 4 toggles between ON (Green) and
OFF.
6
Select the desired parameter by using the CATEGORY [<] and [>]
buttons and change the parameter value with the dial.
Owner’s Manual
47
6. Mixer
7
8
Volume
Determines the Part volume.
Range: 0–127
Pan
Determines the Pan position.
Range: 0–64–127
Reverb Level
Determines the Reverb depth.
Range: 0–127
Chorus Level
Determines the Chorus depth.
Range: 0–127
Repeat steps 4–6 to set other tracks if necessary.
Save the settings here as Style data or Song data.
You can select either USB flash memory or internal memory as the save destination. If you want to save to the USB flash memory, connect the USB flash memory to the USB TO DEVICE terminal.
1 Press the [EXECUTE] button to call up the STYLE CREATOR display or
the SONG EDIT display for saving the data.
2 Select the save destination.
Pressing the [USB] button alternates the save destination between USB flash
memory and internal memory. If you want to save to USB flash memory,
select “Save To USB”; if you want to save to internal memory, select “Save
To USER” in the display.
A default file name will automatically be created.
3 Press the [EXECUTE] button.
4 (Only in the SONG EDIT display) Change the file name as necessary, then
press the [EXECUTE] button again.
For instructions on naming, refer to step 4 on page 57.
5 Press the [+/YES] button to execute the save operation.
9
48
Press the [EXIT] button to return to the Main display.
Owner’s Manual
NOTE
• The settings in the Preset
Song cannot be saved.
NOTE
• For details, refer to the
“Style Creator” chapter or
“Song Edit” chapter in the
Reference Manual.
7
Memorizing Your Favorite Panel Settings
The Registration Memory feature lets you memorize your favorite panel settings for
easy recall whenever they are necessary. Up to 64 complete setups (8 Banks of 8 setups each) can be memorized.
8 Banks
Memory 1
Memory 2
Memory 3
Memory 4
Memory 5
Memory 6
Memory 7
Memory 8
When using Registration Memory, press the [REGIST/PART [MIXER]] button repeatedly until “REGIST” is highlighted at the right bottom of the Main display. With this operation, the eight buttons on the center of the panel can be
used as the Registration Memory buttons.
In the Style mode
(page 35)
In the Song mode
(page 35)
The color is used to indicate the current status of the individual Registration Memory [1] – [8].
• Unlighted................ Contains no data.
• Lit in Green ............ Contains data and not selected.
• Lit in Red ............... Contains data and currently selected.
Panel Settings that can be memorized to the Registration Memory
• Style settings*
Style number, Auto Accompaniment ON/OFF, Split Point, Sections, Style Volume, Chord Fingering, Reverb
Type, Chorus Type
• Tempo
• Voice settings
Main Voice settings: Voice number, Volume, Octave, Pan, Reverb Level, Chorus Level, DSP Level, Dry Level
Dual Voice settings: Dual ON/ OFF, Voice number, Volume, Octave, Pan, Reverb Level, Chorus Level, DSP
Level, Dry Level
Left Voice settings: Left ON/OFF, Voice number, Volume, Octave, Pan, Reverb Level, Chorus Level, DSP
Level, Dry Level
Harmony settings: Harmony ON/OFF, Harmony Type, Harmony Volume
Sustain ON/OFF, DSP ON/OFF, DSP Type, Pitch Bend Range, Upper Octave
• Transpose
• Scale
Scale, Scale Tune, Base Note, Part Select
* Style number, Auto Accompaniment ON/OFF, Sections, Style Volume and Chord Fingering in the Style settings cannot be memorized and called up in the Song mode.
Owner’s Manual
49
7. Memorizing Your Favorite Panel Settings
Memorizing the Panel Settings
1
2
Make the panel settings (page 49) as desired.
Press the REGIST BANK [-]/[+] buttons to select the desired Bank.
As shown below, the REGIST display appears. The dial can also be used to
change values.
NOTE
• The panel settings cannot
be memorized during Song
playback.
Bank number
3
While holding the [MEMORY] button, press one of the unlit Registration Memory [1]–[8] buttons.
When the REGIST is highlighted in the Main display, the pressed button lights
in red, indicating that the panel settings have been memorized.
NOTICE
• If you press the lighted button that already contains
data, the previous data will
be replaced with the new
one.
• Do not turn off the power
during this operation, otherwise the data may be
damaged or lost.
NOTE
• You can save the entire Registration Memory data (64
setups) to the USB flash
memory as backup.
Recalling the Memorized Panel Settings
1
On the Main display, press the [REGIST/PART [MIXER]] button
repeatedly until “REGIST” is highlighted (page 49).
2
Press the REGIST BANK [-]/[+] buttons to select the desired Bank.
As shown below, the REGIST display appears. The dial can also be used to
change values.
Bank number
50
Owner’s Manual
7. Memorizing Your Favorite Panel Settings
3
Press one of the green-lit Registration Memory [1]–[8] buttons.
The color of the pressed button will changed from green to red, indicating that
the memorized panel settings have been called up.
NOTE
• Harmony ON/OFF setting
may not be recalled, or may
be automatically turned off
when the Chord Fingering
type is set to “FullKeyboard.”
Disabling Recall of Specific Items (Freeze)
Registration Memory lets you recall all the panel setups you made with a single button press. However, there may be times that you want certain items to remain the
same, even when switching Registration Memory setups. For example, you may
want to switch Voices or effect settings while keeping the same accompaniment
Style. This is where the Freeze function comes in handy. It lets you maintain the settings of certain items and leave them unchanged, even when selecting other Registration Memory buttons.
1
Select the item to be “frozen.”
Press and hold the [FREEZE] button for longer than a second to call up the Freeze
Group Setting display. Use the dial to select the desired item from Style, Voice,
Tempo, Transpose and Scale, then press the [EXECUTE] button. The on/off status
will be highlighted, allowing you to change it.
Hold for longer than a
second
2
Select “ON.”
Select “ON” for the item not to be recalled, or “OFF” for recall, then press the
[EXECUTE] button. Since the item will be highlighted again for selection,
repeat steps 1–2 (if desired), or press the [EXIT] button to return to the Main
display.
3
Turn the Freeze function on by pressing the [FREEZE] button.
Owner’s Manual
51
7. Memorizing Your Favorite Panel Settings
Registration Clear—Deleting the Specified Registration Memory
1
On the Main display, press the [REGIST/PART [MIXER]] button
repeatedly until “REGIST” is highlighted (page 49).
2
Press the REGIST BANK [-]/[+] buttons to select the desired Bank.
As shown below, the REGIST display appears. The dial can also be used to
change values.
Bank number
3
Press and hold one of the lit Registration Memory [1]–[8] buttons.
A confirmation message will appear in the display.
Hold for longer than a second
To cancel the Clear operation, press the [-/NO] button at this message.
4
52
Press the [+/YES] button to clear the Registration Memory pressed
in Step 3.
The clear-in- progress message will appear briefly on the display while the Registration Memory is being cleared.
Owner’s Manual
8
Initialization
Backup Data and Memory Data
The following settings are always backed up, and are maintained even when the power is turned off. If you want to
initialize the settings (restoring the factory programmed settings), use the Initialize operation as explained below.
Backup data
•
•
•
•
•
•
Registration memory
Auto Fill In On/Off
Touch ON/OFF
Sustain ON/OFF
File save destination in the STYLE CREATOR/SONG EDIT displays
Following parameters in the Function display:
Tuning, Split point, Touch sensitivity, TG mode, Style volume, Song volume,
Metronome volume, Demo cancel, Language, Master EQ type, Chord fingering,
Auto Power Off, Freeze, Demo Group, Demo Play Mode
NOTE
• You can save the Backup
data to your computer, by
using the Musicsoft Downloader (MSD) software. For
details, refer to the Reference Manual.
Memory data
• User Song (recordings of your own performances, or Songs loaded or transferred
from the external device)
• User Style (Created by Style Creator function, or Styles loaded or transferred from
the external device)
• User Music Database (loaded or transferred from the external device)
Initialization
This function erases Backup data or Memory data independently and restores the initial default settings. The following initialization procedures are provided. Expansion contents transferred to internal flash memory by installing the expansion pack cannot be deleted by this function.
Backup Clear
To clear backup data, turn the power on by pressing the [ ] (STANDBY/ON)
switch while holding the highest white key on the keyboard.
NOTE
• The Language setting cannot be restored to the default
setting. Language can be
changed in the Function display (page 12).
Memory Clear
To clear Memory data, turn the power on by pressing the [ ] (STANDBY/ ON)
switch while simultaneously holding the highest white key on the keyboard and the
three highest black keys.
NOTICE
• When you execute the
Clear operation, any User
Songs, User Styles or User
MDBs you have purchased
will also be cleared. Be
sure to save any important
data to a USB flash memory or a computer.
Owner’s Manual
53
9
Using USB Flash Memory
When a USB storage device is inserted in this instrument’s USB TO DEVICE terminal,
User Songs and User Styles created on the instruments and memorized settings can
be saved to or loaded from the device individually.
Precautions when using the [USB TO
DEVICE] terminal
This instrument features a built-in [USB TO
DEVICE] terminal. When connecting a USB device
to the terminal, be sure to handle the USB device with
care. Follow the important precautions below.
Using USB Storage Devices
By connecting the instrument to a USB storage
device, you can save data you’ve created to the connected device, as well as read data from the connected
device.
NOTE
• For more information about the handling of USB devices, refer
to the owner’s manual of the USB device.
The number of USB storage device to be used
One USB storage device can be connected to the
[USB TO DEVICE] terminal.
Compatible USB devices
Formatting USB storage media
• USB storage devices (flash memory, etc.)
When a USB storage device is connected or media is
inserted, a message may appear prompting you to format the device/media. If so, execute the Format operation (page 56).
The instrument does not necessarily support all commercially available USB devices. Yamaha cannot
guarantee operation of USB devices that you purchase. Before purchasing a USB device for use with
this instrument, please visit the following web page:
http://download.yamaha.com/
NOTICE
• The format operation overwrites any previously existing
data. Make sure that the media you are formatting does not
contain important data.
NOTE
• Other USB devices such as a computer keyboard or mouse
cannot be used.
Connecting USB device
• When connecting a USB cable, use a cable no longer
than 3 meters.
• When connecting a USB device to the [USB TO
DEVICE] terminal, make sure that the connector on the
device is appropriate and that it is connected in the
proper direction.
NOTICE
• Though the instrument supports the USB 1.1 standard, you
can connect and use a USB 2.0 storage device with the
instrument. However, note that the transfer speed is that of
USB 1.1.
54
Owner’s Manual
To protect your data (write-protect)
To prevent important data from being inadvertently
erased, apply the write-protect provided with each
storage device or media. If you are saving data to the
USB storage device, make sure to disable write-protect.
Connecting/removing USB storage device
Before removing the media from the device, make
sure that the instrument is not accessing data (such as
in the Save, Delete and Format operations).
NOTICE
• Avoid frequently turning the power on/off to the USB storage device, or connecting/disconnecting the device too
often. Doing so may result in the operation of the instrument “freezing” or hanging up. While the instrument is
accessing data (such as during Save, Delete, Load and
Format operations) or is mounting the USB storage device
(shortly after the connection), do NOT unplug the USB
connector, do NOT remove the media from the device, and
do NOT turn the power off to either device. Doing so may
corrupt the data on either or both devices.
9. Using USB Flash Memory
File Control Display
USB flash memory operations, such as Save and Load
can be performed from the FILE CONTROL display.
1
3
Press the [FILE MENU] button to call up
the FILE CONTROL display.
Connect a USB flash memory to the
USB TO DEVICE terminal, being careful
to insert it in the proper direction.
If the file control functions are accessed while an
unformatted USB flash memory is connected to
the instrument, the “Format” function will automatically be selected. Format a USB flash memory following the instructions presented on page
56.
2
Check that the “CONNECT” message is
shown in the upper right corner of the
Main display.
CONNECT
4
Perform operations such as Save and
Load, as desired.
For details, refer to pages 56–60.
A message (information or confirmation dialog)
sometimes appears in the display to facilitate
operation. Refer to the “Messages” section on
page 67 for an explanation of each message.
NOTE
• No sound will be produced if you play the keyboard
while the FILE CONTROL display is showing. Also, in
this state only buttons related to file functions will be
active.
NOTE
• You cannot access the FILE CONTROL display in any of
the following cases:
• During Style or Song playback/recording.
• When “CONNECT” is not shown in the Main display,
even though a USB flash memory is connected to the
USB TO DEVICE terminal.
Owner’s Manual
55
9. Using USB Flash Memory
Formatting USB Flash Memory
A new USB flash memory must be formatted before it
can be used by this instrument.
NOTICE
• If you format a USB flash memory that already contains
data, all of the data will be erased. Be careful not to erase
important data when using the format function.
5
When the operation is complete, a “Completed” message appears briefly, then
returns to the display of step 2. Press the
[EXIT] button to exit from the FILE CONTROL display.
NOTE
1
Call up the FILE CONTROL display
(page 55).
2
Use the CATEGORY [<] and [>] buttons
to select “USB Format.”
The display prompts you for confirmation.
3
Press the [EXECUTE] button and the display prompts you for confirmation.
You can press the [-/NO] button at this message
to cancel the operation.
4
Press the [EXECUTE] button again, or
the [+/YES] button to execute the format
operation.
NOTICE
• Once the format-in-progress message appears in the
display, the operation cannot be canceled. Never turn
off the power or remove the USB flash memory during
this operation. Doing so could result in damage to the
data.
56
Owner’s Manual
• If the USB flash memory has been write-protected, an
appropriate message will appear in the display and you
will not be able to execute the operation.
9. Using USB Flash Memory
Saving the Registration Memory
All 64 setups memorized to the Registration Memory
can be saved to the USB flash memory as a single file
(extension: usr).
1
2
Make sure that a formatted USB flash
memory has been properly connected
to the USB TO DEVICE terminal, then
call up the FILE CONTROL display
(page 55).
Cursor
left
Cursor
right
Delete
character
Select characters
Use the CATEGORY [<] and [>] buttons
to select “Regist Save.”
A default file name will automatically be created.
Cursor
5
Press the [EXECUTE] button.
The display prompts you for confirmation. You
can cancel the save operation at this message by
pressing the [-/NO] button.
6
Press the [EXECUTE] button again, or
the [+/YES] button to execute the save
operation.
Regist Save
To Overwrite an Existing File
If you want to overwrite a file that already exists
in USB flash memory, use the dial or the [-/NO]
and [+/YES] buttons to select the file, then go to
step 5.
NOTICE
• The amount of time it may take to perform the save
operation depends on the status of the USB flash
memory. Even if this takes a long time, never turn off
the power or remove the USB flash memory during
this operation. Doing so could result in damage to the
data.
NOTE
• If there is not enough capacity left in the USB flash
memory, a message will appear in the display and you
cannot save the data. Erase unnecessary files from the
USB flash memory to make more memory available
(page 60).
3
4
Press the [EXECUTE] button.
A cursor will appear below the first character in
the file name.
Change the file name as necessary.
• The [1] button moves the cursor to the left, and
the [2] button moves it to the right.
• Use the dial to select a character for the current
cursor location.
• The [8] button deletes the character at the cursor location.
NOTE
• If an existing file name is specified, the display prompts
you for confirmation. Press [EXECUTE] or [+/YES] if it is
OK to overwrite the file, or [-/NO] to cancel.
7
When the operation is complete, a “Completed” message appears briefly, then
returns to the display of step 2. Press the
[EXIT] button to exit from the FILE CONTROL display.
The Registration Memory file will be saved to the
USER FILE folder in the USB flash memory.
NOTE
• Perform the Load operation (page 59) if you want to
recall the Registration Memory file on the USB flash
memory to the instrument.
Owner’s Manual
57
9. Using USB Flash Memory
Saving a User Song or User Style
This operation saves one of the User Songs (001–005)
as a SMF File (extension: mid), or one of the User
Styles as a Style File-formatted file (extension: sty).
What is SMF (Standard MIDI File)?
5
Press the [EXECUTE] button.
A cursor will appear below the first character in the
file name.
6
Change the Destination file name as necessary.
For details, refer to step 4 on page 57.
The SMF (Standard MIDI File) format is one of the
most common and widely compatible sequence formats used for storing sequence data. There are two
variations: Format 0 and Format 1. A large number
of MIDI devices are compatible with SMF Format 0,
and most commercially available MIDI sequence
data is provided in SMF Format 0.
1
2
Make sure that a formatted USB flash
memory has been properly connected
to the USB TO DEVICE terminal, then
call up the FILE CONTROL display
(page 55).
Use the CATEGORY [<] and [>] buttons
to select “User Song Save” or “User
Style Save.”
The Source File—a user Song name or a user Style
name in the instrument—will be highlighted.
Cursor
The name of the file to be saved
7
Press the [EXECUTE] button.
The display prompts you for confirmation. You
can cancel the save operation at this message by
pressing the [-/NO] button.
8
Press the [EXECUTE] button again, or
the [+/YES] button to execute the save
operation.
NOTICE
• The amount of time it may take to perform the save
operation depends on the status of the USB flash
memory. Even if this takes a long time, never turn off
the power or remove the USB flash memory during
this operation. Doing so could result in damage to the
data.
The source user Song name.
3
Use the dial to select the source user
Song or Style.
Press the [+/YES] and [-/NO] buttons simultaneously to select the first user Song or Style.
4
Press the [EXECUTE] button.
The Destination Song or Style will be highlighted
with the same name as that of the Source.
9
When the operation is complete, a “Completed” message appears briefly, then
returns to the display of step 2. Press the
[EXIT] button to exit from the FILE CONTROL display.
The file will be saved to the USER FILE folder in
the USB flash memory.
NOTE
To Overwrite an Existing File
If you want to overwrite a file that already exists
on the USB flash memory, use the dial or the [+/
YES] and [-/NO] buttons to select the file, then
go to step 7.
58
Owner’s Manual
• If an existing file name is specified, the display prompts
you for confirmation. Press [EXECUTE] or [+/YES] if it is
OK to overwrite the file, or [-/NO] to cancel.
NOTE
• Perform the Load operation (page 59) if you want to
recall the User Song or User Style saved on the USB
flash memory to the instrument.
9. Using USB Flash Memory
Loading a File
Registration files (extension: usr), Style files (extension: sty), Song files (extension: mid) and MDB files
(extension: MFD) saved to the USER FILE folder in
the USB flash memory can be loaded to the instrument individually.
6
When the operation is complete, a “Completed” message appears briefly, then
returns to the display of step 2. Press the
[EXIT] button to exit from the FILE CONTROL display.
7
Check that the file is properly loaded.
NOTICE
• If the same file name already exists in the instrument, it will
be overwritten and erased. Especially, loading the Registration file will erase all the existing 64 setups. Keep this in
mind when loading a file.
1
Make sure that a formatted USB flash
memory has been connected to the
USB TO DEVICE terminal, then call up
the FILE CONTROL display (page 55).
2
Use the CATEGORY [<] and [>] buttons
to select “Load.”
• When a Registration file is loaded, press one of
the Registration Memory buttons to call up the
panel settings.
• When a Music Database file is loaded, press the
[MDB] button then confirm that the loaded file
name is added on the display.
• When a Song file is loaded, press the [USER]
button then confirm that the loaded file name is
added on the display.
• When a Style file is loaded, press the [EXPANSION/USER] button in the STYLE section then
confirm the loaded file name is added on the
display.
NOTE
• When loading a Song or Style, you should set whether
the DSP Effect is used for the keyboard performance, or
for Song/Style playback. This is because the DSP Effect
can be used only for either part. Set the “TG Mode”
parameter on the Function display.
Currently selected file
3
Use the dial to select the file (Registration, Style, Song or MDB) you want to
load.
4
Press the [EXECUTE] button.
The display prompts you for confirmation. You
can cancel the load operation at this message by
pressing the [-/NO] button.
5
Press the [EXECUTE] button again, or
the [+/YES] button to execute the load
operation.
NOTICE
• Once the load-in-progress message appears in the
display, the operation cannot be canceled. Never turn
off the power or remove the USB flash memory during
this operation. Doing so may corrupt the data on the
device.
Owner’s Manual
59
9. Using USB Flash Memory
Deleting Data from USB Flash Memory
This procedure deletes Registration files, Song files
and Style files in the USB flash memory. The files to
be deleted must be located inside the “USER FILES”
folder on the USB flash memory.
1
2
Make sure that a formatted USB flash
memory has been connected to the
USB TO DEVICE terminal, then call up
the FILE CONTROL display (page 55).
Use the CATEGORY [<] and [>] buttons
to select “USB Delete.”
6
When the operation is complete, a “Completed” message appears briefly, then
returns to the display of step 2. Press the
[EXIT] button to exit from the FILE CONTROL display.
NOTE
• If the USB flash memory has been write-protected, an
appropriate message will appear in the display and you
will not be able to execute the operation.
User Delete
This procedure deletes the selected User Songs, User Styles
and User MDBs in the instrument’s internal memory.
1 Press the [FILE MENU] button.
2 Use the CATEGORY [<] and [>] buttons to locate
“User Delete.”
3 Follow the procedure described above from step 3.
3
Select the file you want to delete.
You can press the [+/YES] and [-/NO] buttons
simultaneously to select the first Song or registration file on the USB flash memory.
4
Press the [EXECUTE] button.
The display prompts you for confirmation.
You can cancel the delete operation at this message by pressing the [-/NO] button.
5
Press the [EXECUTE] button again, or
the [+/YES] button, to execute the delete
operation.
NOTICE
• Once the delete-in-progress message appears in the
display, the operation cannot be canceled. Never turn
off the power or remove the USB flash memory during
this operation. Doing so could result in damage to the
data.
60
Owner’s Manual
10
Expanding Voices and Styles
(Installing to the Expansion Category)
Installing an Expansion Pack (Extension: yep) lets
you add a variety of optional Voices and Styles to each
Expansion category. The installed Voices and Styles
can be selected like Preset Voices and Styles, allowing
you to expand your music performance and creation
possibilities.
Expansion Packs as sample can be downloaded from
the PSR-S650 page within Yamaha Web Site (http://
www.yamaha.com/). Depending on your locale, in
addition, Expansion Packs may be available for
expanding Voices and Styles unique or native to your
locale.
4
Press the [EXECUTE] button
The display prompts you for confirmation. You
can cancel the installation operation at this message by pressing the [-/NO] button.
5
Press the [EXECUTE] button again, or
the [+/YES] button, to execute the installation.
While the Expansion Pack is being installed, a
popup window will indicate the progress.
6
When installation is completed, a message will appear prompting you to turn
off the power and on again. Turn the
power off, then back on.
7
Press the [EXPANSION] button in the
VOICE section, select the installed Voice,
then play the keyboard.
8
Press the [EXPANSION/USER] button in
the STYLE section, select the installed
Style then play the selected Style.
NOTICE
• Installing an Expansion Pack will erase the previously
existing Expansion Pack data in the instrument. We recommend that you keep a copy of the Expansion Pack data in a
separate USB flash memory or a computer.
NOTE
• The Expansion Pack to be installed must be located inside the
“USER FILES” folder on the USB flash memory.
NOTE
• Encrypted Expansion Packs, Packs larger than approx. 16
MB, or Packs for instrument other than the PSR-S650 cannot
be used.
1
2
Make sure that a formatted USB flash
memory has been connected to the
USB TO DEVICE terminal, then call up
the FILE CONTROL display (page 55).
Use the CATEGORY [<] and [>] buttons
to select “Expansion Pack Installation.”
About Song, Style or Registration Memory
including Expansion Voices and Styles
Since installing the Expansion Pack will erase any
Voices and Styles previously existing in the Expansion category, please keep in mind the following
points.
• Any User Song/Style data using the previous
Expansion Voices will produce unexpected sound.
• Unexpected Voices and Styles will be called up, or
no data will be called up from the Registration
Memory you’ve created using the previous Expansion Voices or Styles.
• Any User Song using the previous Expansion
Voices or Styles will produce unexpected sound.
Because of the above points, make sure to record the
name of the installed Expansion Pack when you create original data, such as User Songs using Expansion Voices and Styles.
3
Use the dial to select the Expansion Pack
you want to install.
You can confirm the information of the selected
file by pressing the [START/STOP] button. After
confirming, press the [EXIT] button to return to
the display of step 2.
Owner’s Manual
61
10. Expanding Voices and Styles (Installing to the Expansion Category)
Confirm the Information of the
Expansion Pack
Deleting the Expansion Voice or
Style
You can confirm the information of the currently
installed Expansion Pack on the display.
This operation deletes all the installed Voices or
Styles in the Expansion category, and initializes the
corresponding memory area.
1
2
3
62
Press the [FILE MENU] button.
NOTICE
Use the CATEGORY [<] and [>] buttons
to select “Expansion Pack Information.”
• Any User Song, Style and Registration Memory using the
previous Expansion Contents will produce the unexpected
sound.
1
2
Press the [FILE MENU] button.
3
Press the [EXECUTE] button
The display prompts you for confirmation. You
can cancel the installation operation at this message by pressing the [-/NO] button.
4
Press the [EXECUTE] button again, or
the [+/YES] button to execute the uninstallation operation.
5
When uninstallation is completed, a
message will appear prompting you to
turn off the power and on again. Turn the
power off, then back on.
The installed area is restored to the initial factory
defaults when the power is turned on.
Use the CATEGORY [<] and [>] buttons
to select “Expansion Pack Uninstallation.”
Press the [EXECUTE] button or the
[START/STOP] button to call up the information of the Expansion Pack.
Owner’s Manual
11
Connecting to a Computer
Connecting the instrument to a computer
via a USB cable offers the following useful possibilities:
• The instrument’s performance data can be recorded
with DAW software on the computer, and the performance data from the computer can be played on
the instrument, since the connection allows you to
transmit/receive MIDI messages to/from a computer.
• A file such as a Song or a Style file can be transferred between the computer and instrument with
the Musicsoft Downloader application. For details,
refer to the Reference Manual.
MIDI (Musical Instrument Digital Interface) is a
world-standard interface for communication
between electronic musical instruments and music
devices or computers.
There are two ways to connect the instrument to a
computer:
 Using the function included in your computer’s
operating system
The instrument uses the generic MIDI function
included in your computer’s operating system, so
there’s no need to install any extra driver software.
Operating System (OS):
Windows XP Professional (SP3)/XP Home Edition
(SP3), Windows Vista, Windows 7, Mac OS X Version 10.5–10.6.x
1
Turn off the power of the instrument,
and urn on the power of the computer.
Quit any open application software on the computer.
2
Connect the instrument and the computer via a USB cable.
USB TO HOST terminal
USB cable
3
http://download.yamaha.com/
For instructions on installation, refer to the Install
Guide included in the package file.
Operating System (OS):
For details about OS for Yamaha Standard USBMIDI driver, visit the URL above.
NOTE
• MIDI settings such as the Local Control on/off setting or the
MIDI transmit/receive channel settings can be set in the Function display. For details, refer to the Reference Manual.
MIDI
Computer
 Using Yamaha Standard USB-MIDI driver
When data communication is unstable or some problem occurs even though you’ve executed the above
instructions, download the Yamaha Standard USBMIDI driver from the following URL then install it to
your computer.
Instrument
Precautions when using the USB TO HOST terminal
When connecting the computer to the USB TO HOST
terminal, make sure to observe the following points.
Failing to do so risks freezing the computer and corrupting or losing the data. If the computer or the
instrument freezes, restart the application software or
the computer OS, or turn the power to the instrument
off then on again.
NOTICE
• Use an AB type USB cable of less than about 3 meters.
• Before connecting the computer to the USB TO HOST terminal, exit from any power-saving mode of the computer
(such as suspend, sleep, standby).
• Before turning on the power to the instrument, connect the
computer to the USB TO HOST terminal.
• Execute the following before turning the power to the
instrument on/off or plugging/unplugging the USB cable
to/from the USB TO HOST terminal.
• Quit any open application software on the computer.
• Make sure that data is not being transmitted from the
instrument. (Data is transmitted only by playing notes on
the keyboard or playing back a song.)
• While the computer is connected to the instrument, you
should wait for six seconds or more between these operations: (1) when turning the power of the instrument off
then on again, or (2) when alternately connecting/disconnecting the USB cable.
 MIDI Setup
The MIDI settings can be set individually in the
“MIDI” category of the Function display. For details,
refer to the Reference Manual.
Turn on the power of the instrument.
The computer will automatically be set to enable
MIDI communication with the instrument.
Owner’s Manual
63
Appendix
Appendix
Troubleshooting
Problem
Possible Cause and Solution
Power suddenly and unexpectedly turns off.
This is normal and the Auto Power Off function may have been activated
(page 10). If desired, disable the Auto Power Off function.
When the instrument is turned on or off, a popping sound is temporarily produced.
This is normal and indicates that the instrument is receiving electrical
power.
When using a mobile phone, noise is produced.
Using a mobile phone in close proximity to the instrument may produce
interference. To prevent this, turn off the mobile phone or use it further away
from the instrument.
Check that nothing is connected to the PHONES/OUTPUT jack on the rear
panel. When a set of headphones is plugged into this jack, no sound is output.
There is no sound even when the keyboard is
played or when a song or style is being played
back.
Is “Local Control” set to ON? Make sure “Local Control” is set to ON in the
Function display.
Is the FILE CONTROL display showing? The instrument’s keyboard, etc.,
will not produce any sound while the FILE CONTROL display is showing.
Press the [EXIT] button to return to the Main display.
The style or song does not play back when the
[START/STOP] button is pressed.
Is “External Clock” set to OFF? Make sure “External Clock” is set to OFF in
the Function display.
Make sure that the “Style Volume” is set to an appropriate level in the Function display.
The style does not sound properly.
Is the split point set at an appropriate key for the chords you are playing?
Set the split point at an appropriate key in the Function display.
Is the [ACMP] button lit? If it is not lit, press the [ACMP] button so it lights.
64
No rhythm accompaniment plays when the
[START/STOP] button is pressed after selecting
the BaroqueAir Style in the MOVIE & SHOW
category.
This is not a malfunction. The BaroqueAir Style does not have a Rhythm
part, so there is no rhythm sound for this Style. Also, this Style does not
have a Fill-In section. The other parts will begin playing when you play a
chord in the accompaniment.
Not all of the voices seem to sound, or the
sound seems to be cut off.
The instrument is polyphonic up to a maximum of 64 notes. If the Dual voice
or Split voice is being used and a Style or Song is playing back at the same
time, some notes/sounds may be omitted (or “stolen”) from the accompaniment or Song.
The footswitch (for sustain) seems to produce
the opposite effect. For example, pressing the
footswitch cuts off the sound and releasing it
sustains the sounds.
The polarity of the footswitch is reversed. Make sure that the footswitch plug
is properly connected to the SUSTAIN jack before turning on the power.
The sound of the voice changes from note to
note.
This is normal. The AWM tone generation method uses multiple recordings
(samples) of an instrument across the range of the keyboard; thus, the
actual sound of the voice may be slightly different from note to note.
The Demo display is shown in Japanese, and/or
there are Japanese characters in the display
messages.
Make sure the Language setting in the Function display is set to English.
(See page 12)
The ACMP indicator does not appear when the
[ACMP] button is pressed.
Always press the desired style category button first when you are going to
use any Style-related function.
There is no harmony sound.
The Harmony effects (01–26) behave differently according to their type.
Types 01–10 and 13 function when Style playback is on, chords are played
in the accompaniment range of the keyboard, and a melody is played in the
right-hand range. Types 15–26 will function whether Style playback is on or
off. For types 23–26 you need to play two notes at the same time.
The “OVER CURRENT” message is shown and
the USB device does not respond.
Communication with the USB device has been shut down because of overcurrent to the USB device. Disconnect the device from the USB TO DEVICE
terminal, then turn the power of the instrument off and on again.
Owner’s Manual
Appendix
Panel Button Chart
The below chart lists the buttons/controllers on the panel and the corresponding displays that are called up. Numbers at the left
end correspond to the ones in “Panel Controls and Terminals” (page 8). “” indicates that the detailed information is described
in the Reference Manual (downloadble from website).
No.
Button/Controller
q
w
[
e
[DEMO] button
r
[SONG MODE] button
t
SONG buttons
[PRESET]
[USER]
[SCORE]
[LYRICS]
y
[USB] button
*Pressing
for longer
than a
second
] (Standby/On) switch
MAIN
MASTER VOLUME control
*
i
STYLE buttons
[POP & ROCK]–[EXPANSION/USER]
STYLE CONTROL buttons
[OTS LINK]
[AUTO FILL IN]
*
[ACMP]
!0
DEMO display
FUNCTION - DEMO - Demo Group
—
[REC] button
*
INTRO [I]–[III]
MAIN VARIATION [A]–[D]
ENDING/rit. [I]–[III]
[SYNC STOP]
[SYNC START]
[START/STOP]
SONG CONTROL buttons
[r]
[f]
[
]
[o]
[
]
Page
SONG SELECT - PRESET
SONG SELECT - USER
Score of the current Song
LYRICS
SONG SELECT - USB
(when the [SONG MODE] is turned on)
STYLE SELECT - USB
(when the [SONG MODE] is turned off)
MAIN
(when the [SONG MODE] is turned on)
STYLE CREATOR
(when the [SONG MODE] is turned off)
SONG EDIT
(when the [SONG MODE] is turned on)
11
37
37
35
35
38
38
37
33
40
—

—

29
—
—
—
FUNCTION - OVERALL - Chord Fingering
—
—
—
—
—
—
34
30
29
—
31
31
31
33
30
30
TRANSPOSE buttons
TRANSPOSE
20
!2
METRONOME buttons
—
FUNCTION - METRONOME - Time Signature
27
27
TEMPO
TEMPO
34
34
—
—
FUNCTION - REGIST FREEZE
—
In the Song mode:
REGIST  TR 1-8  TR 9-16  REGIST  …
In the Style mode:
REGIST  ACMP. TR  REGIST  …
MIXER
50
51
51
50
!3
!4
[FREEZE]
[MEMORY]
REGISTRATION MEMORY/SONG Track/STYLE
Track buttons
!5
!6
!7
!8
*
[REGIST/PART [MIXER]]
REGISTRATION MEMORY [1]–[8]/STYLE
Track/SONG Track [1/9]–[8/16]
Display and related controls
[EXIT]
Dial
[-/NO] and [+/YES]
CATEGORY [<] and [>] buttons
[EXECUTE]
*
—
—
—
—
13
14
14
14
15
MDB SELECT
[FILE MENU] button
FILE CONTROL - USB Format
FILE CONTROL - Load
FILE CONTROL - Regist Save
FILE CONTROL - Song Save
FILE CONTROL - Style Save
FILE CONTROL - USB Delete
FILE CONTROL - User Delete
FILE CONTROL - Expansion Pack Installation
FILE CONTROL - Expansion Pack Uninstallation
FILE CONTROL - Expansion Pack Information
FILE CONTROL - Expansion Pack Installation
(When the USB flash memory is connected)
+ CATEGORY [>]
+ CATEGORY [>]
+ CATEGORY [>]
+ CATEGORY [>]
+ CATEGORY [>]
+ CATEGORY [>]
+ CATEGORY [>]
+ CATEGORY [>]
+ CATEGORY [>]
*


49
49
[MDB] button




47
—
MAIN

36
36
39
36
36
!1
*

35
STYLE SELECT
—
—
—
—
—
TEMPO buttons
[+] and [-]
[TAP TEMPO]
REGISTRATION MEMORY-related buttons
REGIST BANK [-] and [+]
Reference
Manual
11
—
u
o
Display called up via the Button
46
55, 56
59
57
58
58
60
60
61
62
62
61
Owner’s Manual
65
Appendix
No.
Button/Controller
*Pressing
for longer
than a
second
[FUNCTION] button
+ CATEGORY [>]
+ CATEGORY [>]
+ CATEGORY [>]
+ CATEGORY [>]
+ CATEGORY [>]
+ CATEGORY [>]
+ CATEGORY [>]
+ CATEGORY [>]
+ CATEGORY [>]
+ CATEGORY [>]
+ CATEGORY [>]
+ CATEGORY [>]
+ CATEGORY [>]
+ CATEGORY [>]
+ CATEGORY [>]
+ CATEGORY [>]
+ CATEGORY [>]
+ CATEGORY [>]
+ CATEGORY [>]
+ CATEGORY [>]
+ CATEGORY [>]
+ CATEGORY [>]
+ CATEGORY [>]
+ CATEGORY [>]
+ CATEGORY [>]
+ CATEGORY [>]
+ CATEGORY [>]
+ CATEGORY [>]
+ CATEGORY [>]
+ CATEGORY [>]
+ CATEGORY [>]
+ CATEGORY [>]
+ CATEGORY [>]
+ CATEGORY [>]
+ CATEGORY [>]
+ CATEGORY [>]
+ CATEGORY [>]
+ CATEGORY [>]
+ CATEGORY [>]
+ CATEGORY [>]
+ CATEGORY [>]
+ CATEGORY [>]
+ CATEGORY [>]
+ CATEGORY [>]
+ CATEGORY [>]
+ CATEGORY [>]
+ CATEGORY [>]
+ CATEGORY [>]
+ CATEGORY [>]
+ CATEGORY [>]
+ CATEGORY [>]
+ CATEGORY [>]
+ CATEGORY [>]
+ CATEGORY [>]
+ CATEGORY [>]
+ CATEGORY [>]
+ CATEGORY [>]
+ CATEGORY [>]
+ CATEGORY [>]
!9
*
@0
@1
VOICE buttons
[PIANO]–[EXPANSION]
VOICE CONTROL buttons
[LEFT]
[HARMONY]
[TOUCH]
[SUSTAIN]
[DSP]
66
34

—
—
FUNCTION - HARMONY - Harmony Type
—
FUNCTION - OVERALL - Touch Sensitivity
—
—
FUNCTION - EFFECT - DSP Type
17
17
17
17
19
—
26
—
19
19
—
UPPER OCTAVE
20
VOICE SELECT (LEFT)
*
VOICE SELECT (DUAL)
*
@3
@4
—
*
*
UPPER OCTAVE buttons
PITCH BEND wheel
Owner’s Manual
Reference
Manual




























































VOICE SELECT (MAIN)
*
Page
—
—
21
20
—
26
—
22
23
23
24
25
51
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
11
—
—
—
—
—
—
—
—
—
27
28
—
—
—
—
—
—
—
—
—
—
—
22
FUNCTION - VOLUME - Style Volume
FUNCTION - VOLUME - Song Volume
FUNCTION - OVERALL - Tuning
FUNCTION - OVERALL - Pitch Bend Range
FUNCTION - OVERALL - Split Point
FUNCTION - OVERALL - Touch Sensitivity
FUNCTION - OVERALL - Chord Fingering
FUNCTION - SCALE TUNE - Scale
FUNCTION - SCALE TUNE - Base Note
FUNCTION - SCALE TUNE - Scale Tune
FUNCTION - SCALE TUNE - Part Select
FUNCTION - SCALE TUNE - External Scale Tune
FUNCTION - REGIST FREEZE - Freeze Group Setting
FUNCTION - MAIN VOICE - Main Volume
FUNCTION - MAIN VOICE - Main Octave
FUNCTION - MAIN VOICE - Main Pan
FUNCTION - MAIN VOICE - Main Reverb Level
FUNCTION - MAIN VOICE - Main Chorus Level
FUNCTION - MAIN VOICE - Main DSP Level
FUNCTION - MAIN VOICE - Main Dry Level
FUNCTION - DUAL VOICE - Dual Volume
FUNCTION - DUAL VOICE - Dual Octave
FUNCTION - DUAL VOICE - Dual Pan
FUNCTION - DUAL VOICE - Dual Reverb Level
FUNCTION - DUAL VOICE - Dual Chorus Level
FUNCTION - DUAL VOICE - Dual DSP Level
FUNCTION - DUAL VOICE - Dual Dry Level
FUNCTION - LEFT VOICE - Left Volume
FUNCTION - LEFT VOICE - Left Octave
FUNCTION - LEFT VOICE - Left Pan
FUNCTION - LEFT VOICE - Left Reverb Level
FUNCTION - LEFT VOICE - Left Chorus Level
FUNCTION - LEFT VOICE - Left DSP Level
FUNCTION - LEFT VOICE - Left Dry Level
FUNCTION - EFFECT - Reverb Type
FUNCTION - EFFECT - Chorus Type
FUNCTION - EFFECT - DSP Type
FUNCTION - EFFECT - Master EQ Type
FUNCTION - HARMONY - Harmony Type
FUNCTION - HARMONY - Harmony Volume
FUNCTION - PC - PC Mode
FUNCTION - MIDI - Local
FUNCTION - MIDI - External Clock
FUNCTION - MIDI - Keyboard Out
FUNCTION - MIDI - Style Out
FUNCTION - MIDI - Song Out
FUNCTION - MIDI - Initial Setup
FUNCTION - METRONOME - Time Signature Numerator
FUNCTION - METRONOME - Time Signature Denominator
FUNCTION - METRONOME - Bell
FUNCTION - METRONOME - Metronome Volume
FUNCTION - SCORE - Quantize
FUNCTION - SCORE - Right Part
FUNCTION - SCORE - Left Part
FUNCTION - DEMO - Demo Group
FUNCTION - DEMO - Demo Play Mode
FUNCTION - DEMO - Demo Cancel
FUNCTION - UTILITY - TG Mode
FUNCTION - UTILITY - Auto Power off
FUNCTION - LANGUAGE - Language
FUNCTION - SCALE TUNE - SCALE
ONE TOUCH SETTING buttons
[DUAL]
@2
Display called up via the Button
16
—
—
20



Appendix
Messages
Message
Description
Opening
Access Error!
The backup data was not recalled properly when turning on the power.
General
Access Error!
Indicates the failure in reading or writing from/to the media, USB flash memory or
the internal flash memory.
Media is not inserted.
Displayed when accessing the media while it is not inserted.
Media is not inserted. Please connect the USB
flash memory to the USB TO DEVICE terminal, or
change the save destination to internal memory.
Displayed when accessing the media while it is not inserted.
Mounting USB device.
Indicates that the media is currently unavailable since the instrument is recognizing the media.
The media is not formatted.
Indicates the inserted media has not been formatted.
The media is write-protected.
Indicates that the inserted media cannot be written since it is write-protected.
Set to the write-protect switch to the “overwrite” position before use.
Media capacity is full.
Displayed when saving data cannot be executed since the media memory
becomes full.
There are too many files.
Indicates that saving data cannot be executed since the total number of files
exceeds the capacity.
The limit of the media has been reached.
Indicates that saving data cannot be executed since the folder/directory structure
has become too complicated.
Data Error!
Displayed when the Song, Style or Expansion Pack contains illegal data, or when
the information of the Expansion Pack is unusable because of the Language setting.
This function is not available now.
Indicates the designated function is not available since the instrument is executing another job.
Style Creator
Do you clear original data?
This message asks you whether you want to create a completely new Style from
scratch.
If yes, press the [+/YES] button, and press the [-/NO] button if not.
NOTICE
Internal memory capacity may not be large enough.
(Delete unwanted style data to make more memory
available if necessary.)
Remaining xxxKB
Internal memory capacity is not large enough to create the Style.
Internal memory capacity is not large enough to
save data.
Style cannot be saved because available space in the internal memory is not sufficient.
Not enough memory for recording.
Any additional Style cannot be recorded because available space in the internal
memory is not sufficient.
The style cannot be used.
The Style cannot be used because the source Style was not loaded properly.
Song Recording
Memory Full
Displayed when the internal memory becomes full during recording.
Song Playback
File too large.
Loading is impossible.
Indicates that loading data cannot be executed since the file data is too large.
Song Edit
Do you want to edit the song?
Internal memory capacity may not be large enough.
(Delete unwanted data to make more memory
available if necessary.)
Remaining xxxKB
Internal memory capacity may not be large enough to save the Song.
Owner’s Manual
67
Appendix
Message
Description
Score
The song data is too large to be converted to notation.
Indicates that the score cannot be displayed since the Song data is too large.
The notation cannot be displayed, since this song is
not allowed to display the notation.
The notation cannot be displayed, since this Song is not allowed to display the
notation.
File Control
Since the media is in use now, this function is not
available.
Indicates that the file control function is currently unavailable since the media is
being accessed.
File is not found.
Indicates there is no file.
Save data is not found.
Displayed when the data to be saved doesn’t exist.
File information area is not large enough.
Indicates that saving data in the media cannot be executed since the total number of files have become too many.
Data was not found.
Displayed when the data to be uninstalled or confirmed the information doesn’t
exist.
Main Display
OVER CURRENT
Communication with the USB device has been shut down because of the overcurrent to the USB device. Disconnect the device from the USB TO DEVICE terminal, then turn on the power of the instrument.
MIDI Receive
MIDI receive buffer overflow.
Displayed when too much MIDI data was received at one time and failed to proceed.
NOTE
• Not all the messages are listed in the table: the messages necessary to be explained only.
68
Owner’s Manual
Appendix
Specifications
Size/Weight
Dimensions
WxDxH
Weight
Keyboard
Display
946 x 405 x 137 mm
(37-1/4" x 15-15/16" x 5-3/8")
7.3Kg (16 lbs. 1 oz.)
Number of Keys
61
Touch Response
Yes
Type
320 x 240 dots
QVGA B/W
4.3 inch display
Contrast
Yes
Score Display Function
Yes
Lyric Display Function
Yes
Language
English/Japanese
Controller
Pitch Bend Wheel
Yes
Panel
Language
Voices
English
Tone Generation
Tone Generating
Technology
AWM Stereo Sampling
Polyphony
Number of Polyphony
(Max.)
64
Number of Voices
357 + 28 Drum/SFX Kits + 480 XG + GM2 (for GM2
Song playback) + GS (for GS Song playback)
Preset
Voice Expansion
Mega Voices
9
Live! Voices
18
Cool! Voices
22
Sweet! Voices
12
Voice
Yes
Wave
Yes (16MB Flash ROM)
Voice Set
Yes
Reverb
35
Compatibility
Types
Effects
Function
Preset
Accompaniment
Styles
Compatibility
Custom
Other Features
XG, XF, GS, GM, GM2
Chorus
44
DSP
237
Master EQ
5
Harmony
26
Dual
Yes
Split
Yes
Panel Sustain
Yes
Number of Preset Styles
181
Fingering
Multi finger, FullKeyboard, AI Fingered
Style Control
Intro x 3, Ending x 3, Main x 4, Fill In x 4
SFF GE
User Styles
Yes
Style Creator
Yes
Music Database
784 + External Files
OTS (One Touch
Setting)
4 for Each Style
Owner’s Manual
69
Appendix
Preset
Custom
Song
Recording
Number of Preset Songs
9
User Songs
Yes
Song Edit
Yes
Number of Songs
5
Tracks
16
Data Capacity
Approx. 30,000 notes (when only “melody” tracks
are recorded)
Recording Function
Quick Recording, Multi Recording, Song
Editing
Compatible Data
Format
Playback
SMF (Format 0 & 1), XF
Recording
SMF (Format 0)
Registration
Registration Memory
8 buttons (x 8 Banks) with Freeze function
Demo
Demonstration
Yes
Metronome
Yes
Tempo Range
5–280
Transpose
-12 – 0 – +12
Tuning
415.3–466.2Hz
Octave buttons
Yes
Scale
Yes
Function
Overall Controls
Expansion Pack Installation
Storage and
Connectivity
Amplifiers and
Speakers
Power Supply
Yes
Internal Memory
1,130 KB
External Drives
Optional USB flash Memory (via USB TO DEVICE)
Connectivity
USB TO HOST, USB TO DEVICE, DC IN 16V,
PHONES/OUTPUT, SUSTAIN
Amplifiers
12W + 12W
Speakers
12cm x 2 + 3cm x 2
Power Supply
Adaptor: PA-300 or an equivalent
recommended by Yamaha
Power Consumption
25 W (When using PA-300 power adaptor)
Auto Power Off Function
Yes
Included Accessories
• Owner’s Manual
• Data List
• Music Rest
• My Yamaha Product User Registration
• AC Power adaptor* (PA-300 or an equivalent
recommended by Yamaha)
* May not be included depending on your particular area.
Please check with your Yamaha dealer.
Optional Accessories
• Adaptor: PA-300 or an equivalent recommended
by Yamaha
• Footswitch: FC4/FC5
• Keyboard Stand: L-6/L-7
• Headphones: HPE-150/HPE-30
* Specifications and descriptions in this owner’s manual are for information purposes only. Yamaha Corp. reserves the right to change or modify
products or specifications at any time without prior notice. Since specifications, equipment or options may not be the same in every locale,
please check with your Yamaha dealer.
70
Owner’s Manual
Appendix
Index
+/YES, -/NO ...............................................................14
.............................................................................36
o ............................................................................. 36
......................................................................... 39
f ........................................................................... 36
r ........................................................................... 36
A
A-B Repeat ..................................................................39
Accessories ...................................................................5
ACMP ..........................................................................29
Auto Accompaniment Range ....................................30
AUTO FILL IN ...........................................................30
Auto Power Off ...........................................................10
B
Backup ......................................................................... 53
Backup Clear .............................................................. 53
Backup data .................................................................53
Bank .............................................................................49
Base Note ....................................................................23
Beat ..............................................................................27
C
CATEGORY ...............................................................14
Chord ...........................................................................32
Chord Fingering ..........................................................32
Chorus ......................................................................... 19
Clear (Song Track) ..................................................... 45
Clear (User Song) .......................................................44
Computer .....................................................................63
CONTRAST ...............................................................12
D
DC IN ..........................................................................10
Delete (File Menu) ..................................................... 60
Delete (User Song) ..................................................... 44
Demo Song ..................................................................37
Dial ..............................................................................14
Display ..................................................................13–15
Drum Kit .....................................................................18
DSP ..............................................................................19
DUAL ..........................................................................17
Dual Voice ...................................................................17
E
Effect ...........................................................................19
Ending ......................................................................... 31
ENDING/rit. ...............................................................31
EXECUTE ..................................................................15
EXIT ............................................................................13
Expansion Pack ...........................................................61
Expansion Styles ........................................................61
Expansion Voices ........................................................61
External Clock ..............................................................7
External Scale Tune ....................................................25
F
FF ................................................................................. 36
File Control ........................................................... 55–60
FILE MENU ............................................................... 55
File Save (File Menu) .......................................... 57–58
Footswitch ................................................................... 10
Format (File Menu) .................................................... 56
Formats ......................................................................... 6
FREEZE ...................................................................... 51
FUNCTION ................................................................ 15
Function Display ........................................................ 15
G
GM ................................................................................ 6
GS .................................................................................. 6
H
HARMONY ............................................................... 19
Headphones ................................................................ 11
I
Initial Setup ................................................................... 7
Initialization ................................................................ 53
Installation .................................................................. 61
INTRO ......................................................................... 31
K
Keyboard Out ............................................................... 7
L
Language ..................................................................... 12
LEFT ........................................................................... 17
Left Voice .................................................................... 17
Left-Part ........................................................................ 7
Load (File Menu) ....................................................... 59
Local .............................................................................. 7
LYRICS ....................................................................... 38
M
MAIN .......................................................................... 30
Main Display .............................................................. 13
MAIN VARIATION (Style) ...................................... 31
Main Voice .................................................................. 16
Manuals ......................................................................... 6
Master Volume ........................................................... 11
MDB ............................................................................ 46
Measure ....................................................................... 13
MEMORY ................................................................... 50
Memory clear ............................................................. 53
Memory data ............................................................... 53
Message ...................................................................... 67
Metronome .................................................................. 27
MIDI .................................................................. 7, 25, 63
Mixer ........................................................................... 47
Multi Recording ......................................................... 41
Music Database .......................................................... 46
Owner’s Manual
71
Appendix
Music Rest ..................................................................12
O
Octave ..........................................................................20
One Touch Setting (OTS) ..........................................34
OTS LINK ...................................................................34
P
Panel Button Chart ..................................................... 65
Panel Controls and Terminals ......................................8
Panel settings .............................................................. 49
Part Assign ..................................................................42
Part Select (Scale) ......................................................24
PAUSE ......................................................................... 36
PC Mode .......................................................................7
PHONES/OUTPUT ...................................................11
Pitch .............................................................................20
PITCH BEND .............................................................20
Power Adaptor ............................................................10
PRESET ......................................................................35
Preset Song ..................................................................36
Q
Quick Recording .........................................................40
R
REC .............................................................................40
Record ......................................................................... 40
REGIST BANK ..........................................................50
REGIST/PART [MIXER] ....................................47, 49
REGISTRATION MEMORY ....................................49
Repeat (A-B Repeat) ..................................................39
Reverb ..........................................................................19
REW ............................................................................36
Right-Part ......................................................................7
S
Save ........................................................................57–58
Scale ............................................................................22
Scale Tune ...................................................................23
SCORE ........................................................................38
Section ................................................................... 30–31
SFF GE ..........................................................................6
SMF (Standard MIDI File) ........................................58
Song .............................................................................35
SONG category ...........................................................35
Song Clear ...................................................................44
SONG CONTROL ..................................................... 36
Song Edit .......................................................................7
SONG MODE .............................................................35
Song Out .......................................................................7
Song Volume .................................................................7
Specifications .............................................................. 69
Split Point ..............................................................17, 30
STANDBY/ON ...........................................................11
START/STOP .............................................................30
Style .............................................................................29
STYLE category .........................................................29
STYLE CONTROL ..............................................30–31
72
Owner’s Manual
Style Creator ................................................................. 7
Style File ............................................................... 58–59
Style Mode .................................................................. 35
Style Out ....................................................................... 7
Style Volume ................................................................ 7
SUSTAIN .............................................................. 10, 19
SUSTAIN (Footswitch) ............................................. 10
Sustain (Panel) ............................................................ 19
SYNC START ............................................................ 30
SYNC STOP ............................................................... 33
T
Tap Start ...................................................................... 30
TAP TEMPO .............................................................. 34
TEMPO ....................................................................... 34
Tempo (Metronome) .................................................. 27
Tempo (Song) ............................................................. 36
Tempo (Style) ............................................................. 34
Time Signature ........................................................... 27
TOUCH ....................................................................... 26
Touch Response .......................................................... 26
Touch Sensitivity ........................................................ 26
Track ............................................................................ 40
Track Clear ................................................................. 45
Track Mute .................................................................... 7
TRANSPOSE ............................................................. 20
Troubleshooting .......................................................... 64
Tuning ......................................................................... 21
Tuning (Scale) ............................................................ 23
U
Uninstallation ............................................................. 62
UPPER OCTAVE ....................................................... 20
USB ......................................................................... 6, 33
USB flash memory ..................................................... 54
USB MIDI Driver ...................................................... 63
USB Song ................................................................... 37
USB Style ................................................................... 33
USB TO DEVICE ...................................................... 54
USB TO HOST .......................................................... 63
USER .............................................................. 35–36, 41
User Song ........................................................ 35–36, 40
V
Voice ............................................................................ 16
VOICE category ......................................................... 16
VOICE CONTROL .................................................... 19
Volume ........................................................................ 11
Volume (Song) .............................................................. 7
Volume (Style) .............................................................. 7
X
XF .................................................................................. 6
XG ................................................................................. 6
1-YEAR LIMITED WARRANTY
ON ARRANGER WORKSTATION KEYBOARDS
Thank you for selecting a Yamaha product. Yamaha products are designed and manufactured to provide a high level of defect-free
performance. Yamaha Corporation of America (“Yamaha”) is proud of the experience and craftsmanship that goes into each and every
Yamaha product. Yamaha sells its products through a network of reputable, specially authorized dealers and is pleased to offer you, the
Original Owner, the following Limited Warranty, which applies only to products that have been (1) directly purchased from Yamaha’s
authorized dealers in the fifty states of the USA and District of Columbia (the “Warranted Area”) and (2) used exclusively in the Warranted
Area. Yamaha suggests that you read the Limited Warranty thoroughly, and invites you to contact your authorized Yamaha dealer or
Yamaha Customer Service if you have any questions.
Coverage:
Yamaha will, at its option, repair or replace the product covered by this warranty if it becomes defective, malfunctions or
otherwise fails to conform with this warranty under normal use and service during the term of this warranty, without charge for labor or
materials. Repairs may be performed using new or refurbished parts that meet or exceed Yamaha specifications for new parts. If
Yamaha elects to replace the product, the replacement may be a reconditioned unit. You will be responsible for any installation or
removal charges and for any initial shipping charges if the product(s) must be shipped for warranty service. However, Yamaha will pay
the return shipping charges to any destination within the USA if the repairs are covered by the warranty. This warranty does not cover (a)
damage, deterioration or malfunction resulting from accident, negligence, misuse, abuse, improper installation or operation or failure to
follow instructions according to the Owner’s Manual for this product; any shipment of the product (claims must be presented to the
carrier); repair or attempted repair by anyone other than Yamaha or an authorized Yamaha Service Center; (b) any unit which has been
altered or on which the serial number has been defaced, modified or removed; (c) normal wear and any periodic maintenance; (d)
deterioration due to perspiration, corrosive atmosphere or other external causes such as extremes in temperature or humidity; (e)
damages attributable to power line surge or related electrical abnormalities, lightning damage or acts of God; or (f) RFI/EMI (Interference/
noise) caused by improper grounding or the improper use of either certified or uncertified equipment, if applicable. Any evidence of
alteration, erasing or forgery of proof-of-purchase documents will cause this warranty to be void. This warranty covers only the Original
Owner and is not transferable.
In Order to Obtain Warranty Service:
Warranty service will only be provided for defective products within the Warranted
Area. Contact your local authorized Yamaha dealer who will advise you of the procedures to be followed. If this is not successful, contact
Yamaha at the address, telephone number or website shown below. Yamaha may request that you send the defective product to a local
authorized Yamaha Servicer or authorize return of the defective product to Yamaha for repair. If you are uncertain as to whether a dealer
has been authorized by Yamaha, please contact Yamaha’s Service Department at the number shown below, or check Yamaha’s website
at www.Yamaha.com. Product(s) shipped for service should be packed securely and must be accompanied by a detailed explanation of
the problem(s) requiring service, together with the original or a machine reproduction of the bill of sale or other dated, proof-of-purchase
document describing the product, as evidence of warranty coverage. Should any product submitted for warranty service be found
ineligible therefore, an estimate of repair cost will be furnished and the repair will be accomplished only if requested by you and upon
receipt of payment or acceptable arrangement for payment.
Limitation of Implied Warranties and Exclusion of Damages: ANY IMPLIED WARRANTIES, INCLUDING
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE SHALL BE LIMITED IN DURATION TO THE
APPLICABLE PERIOD OF TIME SET FORTH ABOVE. YAMAHA SHALL NOT BE RESPONSIBLE FOR INCIDENTAL OR
CONSEQUENTIAL DAMAGES OR FOR DAMAGES BASED UPON INCONVENIENCE, LOSS OF USE, DAMAGE TO ANY OTHER
EQUIPMENT OR OTHER ITEMS AT THE SITE OF USE OR INTERRUPTION OF PERFORMANCES OR ANY CONSEQUENCES.
YAMAHA’S LIABILITY FOR ANY DEFECTIVE PRODUCT IS LIMITED TO REPAIR OR REPLACEMENT OF THE PRODUCT, AT
YAMAHA’S OPTION. SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS OR THE
EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION OR EXCLUSION
MAY NOT APPLY TO YOU. This Warranty gives you specific legal rights, and you may also have other rights which vary from state to
state. This is the only express warranty applicable to the product specified herein; Yamaha neither assumes nor authorizes anyone to
assume for it any other express warranty.
If you have any questions about service received or if you need assistance in locating an authorized Yamaha Servicer, please contact:
CUSTOMER SERVICE
Yamaha Corporation of America
6600 Orangethorpe Avenue, Buena Park, California 90620-1373
Telephone: 800-854-1569
www.yamaha.com
Do not return any product to the above address without a written Return Authorization issued by Yamaha.
©2009 Yamaha Corporation of America.
Effective: 11/01/09
For details of products, please contact your nearest Yamaha
representative or the authorized distributor listed below.
Para detalles sobre productos, contacte su tienda Yamaha más
cercana o el distribuidor autorizado que se lista debajo.
Pour plus de détails sur les produits, veuillez-vous adresser à Yamaha
ou au distributeur le plus proche de vous figurant dans la liste suivante.
Die Einzelheiten zu Produkten sind bei Ihrer unten aufgeführten
Niederlassung und bei Yamaha Vertragshändlern in den jeweiligen
Bestimmungsländern erhältlich.
Para obter detalhes de produtos, entre em contato com o
representante mais próximo da Yamaha ou com o distribuidor
autorizado relacionado a seguir.
NORTH AMERICA
CANADA
Yamaha Canada Music Ltd.
135 Milner Avenue, Scarborough, Ontario,
M1S 3R1, Canada
Tel: 416-298-1311
U.S.A.
Подробные сведения об инструменте можно получить у местного
представителя корпорации Yamaha или уполномоченного
дистрибьютора, указанного в следующем списке.
THE NETHERLANDS/
BELGIUM/LUXEMBOURG
FRANCE
Yamaha Musique France
BP 70-77312 Marne-la-Vallée Cedex 2, France
Tel: 01-64-61-4000
Yamaha Corporation of America
6600 Orangethorpe Ave., Buena Park, Calif. 90620,
U.S.A.
Tel: 714-522-9011
ITALY
CENTRAL & SOUTH AMERICA
SPAIN/PORTUGAL
MEXICO
Yamaha de México S.A. de C.V.
Calz. Javier Rojo Gómez #1149,
Col. Guadalupe del Moral
C.P. 09300, México, D.F., México
Tel: 55-5804-0600
BRAZIL
Yamaha Musical do Brasil Ltda.
Rua Joaquim Floriano, 913 - 4' andar, Itaim Bibi,
CEP 04534-013 Sao Paulo, SP. BRAZIL
Tel: 011-3704-1377
ARGENTINA
Yamaha Music Latin America, S.A.
Sucursal de Argentina
Olga Cossettini 1553, Piso 4 Norte
Madero Este-C1107CEK
Buenos Aires, Argentina
Tel: 011-4119-7000
PANAMA AND OTHER LATIN
AMERICAN COUNTRIES/
CARIBBEAN COUNTRIES
Yamaha Music Latin America, S.A.
Torre Banco General, Piso 7, Urbanización Marbella,
Calle 47 y Aquilino de la Guardia,
Ciudad de Panamá, Panamá
Tel: +507-269-5311
ASIA
Yamaha Music Europe Branch Benelux
Clarissenhof 5-b, 4133 AB Vianen, The Netherlands
Tel: 0347-358 040
Yamaha Musica Italia S.P.A.
Viale Italia 88, 20020 Lainate (Milano), Italy
Tel: 02-935-771
Yamaha Música Ibérica, S.A.
Ctra. de la Coruna km. 17, 200, 28230
Las Rozas (Madrid), Spain
Tel: 91-639-8888
EUROPE
Yamaha Music U.K. Ltd.
Sherbourne Drive, Tilbrook, Milton Keynes,
MK7 8BL, England
Tel: 01908-366700
GERMANY
Yamaha Music Europe GmbH
Siemensstraße 22-34, 25462 Rellingen, Germany
Tel: 04101-3030
SWITZERLAND/LIECHTENSTEIN
Yamaha Music Europe GmbH
Branch Switzerland in Zürich
Seefeldstrasse 94, 8008 Zürich, Switzerland
Tel: 01-383 3990
AUSTRIA
Yamaha Music Europe GmbH Branch Austria
Schleiergasse 20, A-1100 Wien, Austria
Tel: 01-60203900
CZECH REPUBLIC/SLOVAKIA/
HUNGARY/SLOVENIA
Yamaha Music Europe GmbH Branch Austria
Schleiergasse 20, A-1100 Wien, Austria
Tel: 01-602039025
POLAND/LITHUANIA/LATVIA/ESTONIA
Yamaha Music Europe GmbH
Branch Sp.z o.o. Oddzial w Polsce
ul. 17 Stycznia 56, PL-02-146 Warszawa, Poland
Tel: 022-500-2925
Yamaha Music & Electronics (China) Co.,Ltd.
2F, Yunhedasha, 1818 Xinzha-lu, Jingan-qu,
Shanghai, China
Tel: 021-6247-2211
HONG KONG
Tom Lee Music Co., Ltd.
11/F., Silvercord Tower 1, 30 Canton Road,
Tsimshatsui, Kowloon, Hong Kong
Tel: 2737-7688
INDIA
Yamaha Music India Pvt. Ltd.
5F Ambience Corporate Tower Ambience Mall Complex
Ambience Island, NH-8, Gurgaon-122001, Haryana, India
Tel: 0124-466-5551
INDONESIA
GREECE
Philippos Nakas S.A. The Music House
147 Skiathou Street, 112-55 Athens, Greece
Tel: 01-228 2160
SWEDEN
PT. Yamaha Musik Indonesia (Distributor)
PT. Nusantik
Gedung Yamaha Music Center, Jalan Jend. Gatot
Subroto Kav. 4, Jakarta 12930, Indonesia
Tel: 021-520-2577
KOREA
Yamaha Scandinavia AB
J. A. Wettergrens Gata 1, Box 30053
S-400 43 Göteborg, Sweden
Tel: 031 89 34 00
Yamaha Music Korea Ltd.
8F, 9F, Dongsung Bldg. 158-9 Samsung-Dong,
Kangnam-Gu, Seoul, Korea
Tel: 02-3467-3300
DENMARK
YS Copenhagen Liaison Office
Generatorvej 6A, DK-2730 Herlev, Denmark
Tel: 44 92 49 00
FINLAND
F-Musiikki Oy
Kluuvikatu 6, P.O. Box 260,
SF-00101 Helsinki, Finland
Tel: 09 618511
MALAYSIA
Yamaha Music (Malaysia) Sdn., Bhd.
Lot 8, Jalan Perbandaran, 47301 Kelana Jaya,
Petaling Jaya, Selangor, Malaysia
Tel: 03-78030900
PHILIPPINES
Yupangco Music Corporation
339 Gil J. Puyat Avenue, P.O. Box 885 MCPO,
Makati, Metro Manila, Philippines
Tel: 819-7551
NORWAY
Norsk filial av Yamaha Scandinavia AB
Grini Næringspark 1, N-1345 Østerås, Norway
Tel: 67 16 77 70
ICELAND
THE UNITED KINGDOM/IRELAND
THE PEOPLE’S REPUBLIC OF CHINA
Skifan HF
Skeifan 17 P.O. Box 8120, IS-128 Reykjavik, Iceland
Tel: 525 5000
RUSSIA
Yamaha Music (Russia)
Room 37, bld. 7, Kievskaya street, Moscow,
121059, Russia
Tel: 495 626 5005
OTHER EUROPEAN COUNTRIES
Yamaha Music Europe GmbH
Siemensstraße 22-34, 25462 Rellingen, Germany
Tel: +49-4101-3030
SINGAPORE
Yamaha Music (Asia) Pte., Ltd.
#03-11 A-Z Building
140 Paya Lebor Road, Singapore 409015
Tel: 6747-4374
TAIWAN
Yamaha KHS Music Co., Ltd.
3F, #6, Sec.2, Nan Jing E. Rd. Taipei.
Taiwan 104, R.O.C.
Tel: 02-2511-8688
THAILAND
Siam Music Yamaha Co., Ltd.
4, 6, 15 and 16th floor, Siam Motors Building,
891/1 Rama 1 Road, Wangmai,
Pathumwan, Bangkok 10330, Thailand
Tel: 02-215-2622
OTHER ASIAN COUNTRIES
AFRICA
Yamaha Corporation,
Asia-Pacific Sales & Marketing Group
Nakazawa-cho 10-1, Naka-ku, Hamamatsu,
Japan 430-8650
Tel: +81-53-460-2317
Yamaha Corporation,
Asia-Pacific Sales & Marketing Group
Nakazawa-cho 10-1, Naka-ku, Hamamatsu,
Japan 430-8650
Tel: +81-53-460-2317
OCEANIA
AUSTRALIA
MIDDLE EAST
TURKEY/CYPRUS
Yamaha Music Europe GmbH
Siemensstraße 22-34, 25462 Rellingen, Germany
Tel: 04101-3030
OTHER COUNTRIES
Yamaha Music Gulf FZE
LOB 16-513, P.O.Box 17328, Jubel Ali,
Dubai, United Arab Emirates
Tel: +971-4-881-5868
Yamaha Music Australia Pty. Ltd.
Level 1, 99 Queensbridge Street, Southbank,
Victoria 3006, Australia
Tel: 3-9693-5111
NEW ZEALAND
Music Works LTD
P.O.BOX 6246 Wellesley, Auckland 4680,
New Zealand
Tel: 9-634-0099
COUNTRIES AND TRUST
TERRITORIES IN PACIFIC OCEAN
Yamaha Corporation,
Asia-Pacific Sales & Marketing Group
Nakazawa-cho 10-1, Naka-ku, Hamamatsu,
Japan 430-8650
Tel: +81-53-460-2317
HEAD OFFICE Yamaha Corporation, Digital Musical Instruments Division
EKB54
Nakazawa-cho 10-1, Naka-ku, Hamamatsu, Japan 430-8650
Tel: +81-53-460-3273
Yamaha Global Home
http://www.yamaha.com/
Yamaha Manual Library
http://www.yamaha.co.jp/manual/
U.R.G., Digital Musical Instruments Division
© 2011 Yamaha Corporation
***POTY*.*-01A0
Printed in China
WW73170
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising