Weslo | WLTL49907.0 | User`s manual | Weslo WLTL49907.0 User`s manual

Weslo WLTL49907.0 User`s manual
Model No. WLTL49907.0
Serial No.
Write the serial number in the
space above for future reference.
USER'S MANUAL
Serial Number Decal
QUESTIONS?
As a manufacturer, we are committed to providing complete customer satisfaction. If you have
questions, or if parts are missing,
PLEASE DO NOT CONTACT THE
STORE; please contact
Customer Care.
IMPORTANT: You must note the
product model number and
serial number (see the drawing
above) before contacting us:
CALL TOLL-FREE:
1-866-699-3756
Mon.–Fri. 6 a.m.–6 p.m. MST
Sat. 8 a.m.–4 p.m. MST
ON THE WEB:
www.wesloservice.com
CAUTION
Visit our website at
Read all precautions and instructions in this manualwww.proform.com
before using
this equipment. Save this manual
for future reference.new products, prizes,
fitness tips, and much more!
Visit our website at
www.weslo.com
new products, prizes,
fitness tips, and much more!
TABLE OF CONTENTS
WARNING DECAL PLACEMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
IMPORTANT PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
BEFORE YOU BEGIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
OPERATION AND ADJUSTMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
HOW TO FOLD AND MOVE THE TREADMILL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
EXERCISE GUIDELINES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
PART LIST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
EXPLODED DRAWING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24
ORDERING REPLACEMENT PARTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Back Cover
LIMITED WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Back Cover
WARNING DECAL PLACEMENT
The decals shown here have been placed on the
treadmill. If a decal is missing or illegible, call the
telephone number on the front cover of this manual and request a free replacement decal. Apply
the decal in the location shown. Note: The decals
may not be shown at actual size.
WESLO is a registered trademark of ICON IP, Inc.
2
IMPORTANT PRECAUTIONS
WARNING:
To reduce the risk of serious injury, read all important precautions and instructions in this manual and all warnings on your treadmill before using your treadmill. ICON assumes no responsibility for personal injury or property damage sustained by or through the use of
this product.
carrying 15 or more amps. No other appliance
should be on the same circuit. Do not use an
extension cord.
1. Before beginning any exercise program, consult your physician. This is especially important for persons over the age of 35 or persons
with pre-existing health problems.
12. Use only a single-outlet surge suppressor
that meets all of the specifications described
on page 10. To purchase a surge suppressor,
see your local WESLO dealer or call the telephone number on the front cover of this manual and order part number 146148, or see
your local electronics store.
2. It is the responsibility of the owner to ensure
that all users of this treadmill are adequately
informed of all warnings and precautions.
3. Use the treadmill only as described.
4. Place the treadmill on a level surface, with at
least 8 ft. (2.4 m) of clearance behind it and 2
ft. (0.6 m) on each side. Do not place the
treadmill on any surface that blocks air openings. To protect the floor or carpet from damage, place a mat under the treadmill.
13. Failure to use a properly functioning surge
suppressor could result in damage to the control system of the treadmill. If the control system is damaged, the walking belt may change
speed, accelerate, or stop unexpectedly,
which may result in a fall and serious injury.
5. Keep the treadmill indoors, away from moisture and dust. Do not put the treadmill in a
garage or covered patio, or near water.
14. Keep the power cord and the surge suppressor away from heated surfaces.
6. Do not operate the treadmill where aerosol
products are used or where oxygen is being
administered.
15. Never move the walking belt while the power
is turned off. Do not operate the treadmill if
the power cord or plug is damaged, or if the
treadmill is not working properly. (See TROUBLESHOOTING on page 19 if the treadmill is
not working properly.)
7. Keep children under the age of 12 and pets
away from the treadmill at all times.
8. The treadmill should be used only by persons
weighing 300 lbs. (136 kg) or less.
16. Read, understand, and test the emergency
stop procedure before using the treadmill (see
HOW TO TURN ON THE POWER on page 12).
9. Never allow more than one person on the
treadmill at a time.
17. Never start the treadmill while you are standing on the walking belt. Always hold the
handrails while using the treadmill.
10. Wear appropriate exercise clothes when
using the treadmill. Do not wear loose clothes
that could become caught in the treadmill.
Athletic support clothes are recommended for
both men and women. Always wear athletic
shoes. Never use the treadmill with bare feet,
wearing only stockings, or in sandals.
18. The treadmill is capable of high speeds.
Adjust the speed in small increments to avoid
sudden jumps in speed.
19. The pulse sensor is not a medical device.
Various factors, including the user's movement, may affect the accuracy of heart rate
readings. The pulse sensor is intended only
as an exercise aid in determining heart rate
trends in general.
11. When connecting the power cord (see page
10), plug the power cord into a surge suppressor (not included) and plug the surge
suppressor into a grounded circuit capable of
3
20. Use the dumbbells only as described in this
manual. Properly store the dumbbells in the
dumbbell holders on the console when you
are not using them. If the dumbbells are improperly stored, they may fall off the console,
causing the user to trip.
24. Never insert any object into any opening on
the treadmill.
25. Inspect and properly tighten all parts of the
treadmill regularly.
26.
21. Never leave the treadmill unattended while it
is running. Always remove the key, unplug
the power cord, and switch the reset/off circuit breaker to the off position when the
treadmill is not in use. (See the drawing on
page 5 for the location of the circuit breaker.)
DANGER: Always unplug the power
cord immediately after use, before cleaning the
treadmill, and before performing the maintenance and adjustment procedures described in
this manual. Never remove the motor hood unless instructed to do so by an authorized service representative. Servicing other than the
procedures in this manual should be performed
by an authorized service representative only.
22. Do not attempt to raise, lower, or move the
treadmill until it is properly assembled. (See
ASSEMBLY on page 6, and HOW TO FOLD
AND MOVE THE TREADMILL on page 17.)
You must be able to safely lift 45 lbs. (20 kg)
to raise, lower, or move the treadmill.
27. This treadmill is intended for in-home use
only. Do not use this treadmill in a commercial, rental, or institutional setting.
23. When folding or moving the treadmill, make
sure that the storage latch is fully closed.
SAVE THESE INSTRUCTIONS
4
BEFORE YOU BEGIN
Thank you for selecting the revolutionary WESLO®
CADENCE 65 CROSSTRAINER treadmill. The
CADENCE 65 CROSSTRAINER treadmill offers an
impressive array of features designed to make your
workouts at home more enjoyable and effective. And
when you’re not exercising, the unique CADENCE 65
CROSSTRAINER treadmill can be folded up, requiring
less than half the floor space of other treadmills.
ual. To help us assist you, note the product model
number and serial number before contacting us. The
model number and the location of the serial number
decal are shown on the front cover of this manual.
To avoid a registration fee for any service needed
under warranty, you must register the treadmill at
www.wesloservice.com/registration.
For your benefit, read this manual carefully before
using the treadmill. If you have questions after reading this manual, please see the front cover of this man-
Before reading further, please review the drawing
below and familiarize yourself with the labeled parts.
Fan
Dumbbell/Water Bottle Holder*
Console
Handgrip Pulse Sensor
Key/Clip
Handrail
Storage Latch
Upright
Reset/Off
Circuit Breaker
Walking Belt
Power Cord
Foot Rail
Cushioned Walking Platform
*To purchase dumbbells (not included), call the telephone number
on the front cover of this manual.
Rear Roller
Adjustment Bolts
5
Star Washer
(106)–4
Washer (38)–4
2 1/2” Bolt (37)–2
ASSEMBLY
To hire an authorized service technician to assemble the treadmill, call 1-800-445-2480. Assembly requires
Nut Do
(32)–2
3 1/2” Bolt
two persons. Set the treadmill
in a (45)–4
cleared area and remove all packing Wheel
materials.
not dispose of the packing
materials until assembly is completed. Note: The underside of the treadmill walking belt is coated with high-performance lubricant. During shipping, a small amount of lubricant may be transferred to the top of the walking belt or
the shipping carton. This is a normal condition and does not affect treadmill performance. If there is Handrail
lubricantBolt
on (64)–4
top of the walking belt, simply wipe off the lubricant with a soft cloth and a mild, non-abrasive cleaner.
Assembly requires the included hex key
least 6" long) and wire cutters
.
and your own Phillips screwdriver
(with a shaft at
Use the drawings below to identify the assembly hardware. The number in parentheses below each drawing is
Star Washer
Extension Leg Bolt (96)–4
(84)–2the key number of the part, from the PART LIST near the end of the manual. The number after the parentheses
Wheel
Nut
(13)–2
Extension
Legfor
Bolt
(96)–4 Note: If a part is not in the parts bag, check to see if it is preatshows the quantity
needed
assembly.
tached to one of the parts to be assembled. Extra hardware may be included. To avoid damaging plastic
parts, do not use power tools for assembly.
Ground Screw
(33)–1
Screw (3)–11
2.25" Extension Leg Bolt (92)–2
Star Washer (8)–8
Front Endcap
Screw (14)–2
1" Tek Screw (83)–2
2.5" Extension Leg Bolt (65)–2
Extension Leg Nut (67)–2
Handrail Bolt (64)–4
1. Make sure that the power cord is unplugged.
1
With the help of a second person, carefully tip
the treadmill onto its left side as shown. Partially
fold the Frame (58) so the treadmill is more stable. Do not fully fold the Frame until the
treadmill is completely assembled.
14
84
44
92
Insert an Extension Leg (89) into the base of the
Uprights (84). Hold an Extension Leg Nut (67) in
the bottom of the Extension Leg, and thread a
2.25" Extension Leg Bolt (92) with a Star
Washer (8) into the top of the Extension Leg.
Next, thread a 2.5" Extension Leg Bolt (65) with a
Star Washer (8) into the bottom of the Extension
Leg. Firmly tighten the Extension Leg Bolts.
8
8
89
67
65
58
Slide a Front Endcap (44) onto the base of the
Upright (84). Partially tighten a Front Endcap
Screw (14) into the Front Endcap and the base.
6
2. With the help of a second person, carefully tip
the treadmill onto its right side. Do not fully fold
the Frame (58) until the treadmill is completely assembled.
2
14
Insert the other Extension Leg (89) into the base
of the Uprights (84). Hold an Extension Leg
Nut (67) in the bottom of the Extension Leg, and
thread a 2.25" Extension Leg Bolt (92) with a
Star Washer (8) into the top of the Extension
Leg. Next, thread a 2.5" Extension Leg Bolt (65)
with a Star Washer (8) into the bottom of the
Extension Leg. Firmly tighten the Extension
Leg Bolts.
84
92
44
8
65
8
67
89
58
Slide the other Front Endcap (44) onto the base
of the Upright (84). Partially tighten a Front
Endcap Screw (14) into the Front Endcap and
the base.
3. Attach two Base Pads (82) to the base of the
Uprights (84) with two 1" Tek Screws (83).
3
83
82
84
83
82
4. With the help of a second person, carefully raise
the Uprights (84) to a vertical position.
4
64
Have the second person hold the Handrail (20)
near the Uprights (84). Insert the Wire Harness
(77) into the hole in the bottom of the Handrail
and out of the top as shown.
64
8
Next, set the Handrail (20) on the Uprights (84).
Do not let the Wire Harness (77) fall into the
right Upright.
8
20
77
Attach the Handrail (20) with four Handrail Bolts
(64) and four Star Washers (8); start all four
Handrail Bolts and then firmly tighten them.
84
See steps 1 and 2. Fully tighten the two
Front Endcap Screws (14).
7
5. While a second person holds the console assembly near the Handrail (20), attach the
ground wire to the indicated hole in the Handrail
with a Ground Screw (33).
5
Ground
Wire
33
Hole
20
Console
Assembly
6. While the second person continues to hold the
console assembly, locate the wire underneath
the console assembly.
6
Connect the wire from the console assembly to
the Wire Harness (77). See the inset drawing.
The connectors should slide together easily
and snap into place. If the connectors do not
slide together easily and snap into place, turn
one connector and then try again. IF THE CONNECTORS ARE NOT CONNECTED PROPERLY, THE CONSOLE MAY BE DAMAGED
WHEN THE POWER IS TURNED ON. Insert
the connectors downward into the Handrail (20).
77
Wire
77
Console
Assembly
20
7. Set the console assembly on the Handrail (20).
Be careful to avoid pinching any of the
wires. Make sure that the ground wire (see
step 5) and the wire from the console assembly (see step 6) are in the indicated channel.
7
Console Assembly
Channel
Hand tighten five Screws (3) into the Handrail
(20) and the console assembly. Do not put
Screws into the two indicated holes. Start all
five Screws, but do not tighten them yet.
20
3
3
No Screws
8
3
8. Hand tighten four additional Screws (3) into the
Handrail (20) and the console assembly. Then,
tighten all nine Screws used in step 7 and
this step; do not overtighten the Screws.
8
Console Assembly
3
20
3
9. Attach the Latch Housing (73) to the left Upright
(84) with two Screws (3); start both Screws
and then tighten them. Note: Make sure that
the large hole in the Latch Housing is on the
indicated side.
3
9
84
73
Remove the latch knob from the latch pin. Make
sure that the collar and the spring are on the
latch pin. (Note: If there are two collars, place
one on each side of the spring.) Next, insert the
latch pin into the Latch Housing (73). Then,
tighten the latch knob onto the latch pin.
Latch Knob
3
Spring
Collar
Large Hole
Latch
Pin
10. Make sure that all parts are properly tightened before you use the treadmill. If there are sheets of clear
plastic on the treadmill decals, remove the plastic. To protect the floor or carpet, place a mat under the treadmill. Note: Extra hardware may be included. Keep the included hex key in a secure place; the hex key is used
to adjust the walking belt (see page 20).
If you purchase the optional chest pulse sensor (see page 16), follow the steps below to install the receiver
included with the chest pulse sensor.
1. Remove the key from the console and unplug
the power cord.
85
Remove the Screw (3) and the Access Door
(76) from the back of the Console Base (85).
2. Connect the wire on the receiver (A) to the indicated wire extending from the Console Base
(85). Hold the receiver so the small cylinder
is oriented as shown and is facing the
Console Base. Attach the receiver to the plastic
posts on the Access Door (76) with the two included small screws.
Small Screws
Wire
A
Small
Cylinder
3. Make sure that no wires are pinched.
Reattach the Access Door (76) with the Screw
(3). Discard the other wires included with the receiver.
3
76
9
OPERATION AND ADJUSTMENT
THE PRE-LUBRICATED WALKING BELT
tric shock. This product is equipped with a cord having
an equipment-grounding conductor and a grounding
plug. Plug the power cord into a surge suppressor,
and plug the surge suppressor into an appropriate
outlet that is properly installed and grounded in
accordance with all local codes and ordinances.
Important: The treadmill is not compatible with
GFCI-equipped outlets.
Your treadmill features a walking belt coated with highperformance lubricant. IMPORTANT: Never apply silicone spray or other substances to the walking
belt or the walking platform. Such substances will
deteriorate the walking belt and cause excessive
wear.
HOW TO PLUG IN THE POWER CORD
This product is for use on a nominal 120-volt circuit,
and has a grounding plug that looks like the plug illustrated in drawing 1 below. A temporary adapter that
looks like the adapter illustrated in drawing 2 may be
used to connect the surge suppressor to a 2-pole
receptacle as shown in drawing 2 if a properly
grounded outlet is not available.
DANGER: Improper connection
of the equipment-grounding conductor can
result in an increased risk of electric shock.
Check with a qualified electrician or serviceman if you are in doubt as to whether the
product is properly grounded. Do not modify
the plug provided with the product—if it will
not fit the outlet, have a proper outlet
installed by a qualified electrician.
1
Grounded Outlet Box
Surge Suppressor
Grounding Pin
Your treadmill, like any other type of sophisticated
electronic equipment, can be seriously damaged by
sudden voltage changes in your home’s power.
Voltage surges, spikes, and noise interference can
result from weather conditions or from other appliances
being turned on or off. To decrease the possibility of
your treadmill being damaged, always use a surge
suppressor with your treadmill (see drawing 1 at
the right). To purchase a surge suppressor, see
your local WESLO dealer or call the telephone
number on the front cover of this manual and order
part number 146148, or see your local electronics
store.
Grounding Pin
Grounded Outlet
Grounding Plug
2
Grounded Outlet Box
Adapter
Use only a single-outlet surge suppressor that is
UL 1449 listed as a transient voltage surge suppressor (TVSS). The surge suppressor must have a
UL suppressed voltage rating of 400 volts or less
and a minimum surge dissipation of 450 joules.
The surge suppressor must be electrically rated for
120 volts AC and 15 amps. There must be a monitoring light on the surge suppressor to indicate
whether it is functioning properly. Failure to use a
properly functioning surge suppressor could result
in damage to the control system of the treadmill. If
the control system is damaged, the walking belt
may change speed, accelerate or stop unexpectedly, which may result in a fall and serious injury.
Surge Suppressor
Lug
Metal Screw
The temporary adapter should be used only until a
properly grounded outlet (drawing 1) can be installed
by a qualified electrician.
The green-colored rigid ear, lug, or the like extending
from the adapter must be connected to a permanent
ground such as a properly grounded outlet box cover.
Whenever the adapter is used it must be held in place
by a metal screw. Some 2-pole receptacle outlet box
covers are not grounded. Contact a qualified electrician to determine if the outlet box cover is
grounded before using an adapter.
This product must be grounded. If it should malfunction or break down, grounding provides a path of least
resistance for electric current, reducing the risk of elec-
10
CONSOLE DIAGRAM
Clip
Key
FEATURES OF THE CONSOLE
The revolutionary treadmill console offers a selection
of features designed to make your workouts more
effective.
ETPF59806
PFTL59806
When you select the manual mode of the console,
you
can change the speed and incline of the treadmill with
the touch of a button. As you exercise, the console will
display continuous exercise feedback. You can even
measure your heart rate using the handgrip pulse sensor or the optional chest pulse sensor (see page 16 for
information about the optional chest pulse sensor).
The console also features six interactive cross trainer
programs designed to help you to burn calories and
enhance your cardiovascular system while toning and
strengthening your muscles. The cross trainer programs automatically control the speed and incline of
the treadmill and prompt you to perform a variety of
strength exercises during your workout. There are two
whole body, two upper body, and two lower body cross
trainer programs to choose among. Note: The strength
exercises require the use of dumbbells and an inflatable exercise ball (not included). To purchase dumbbells or an exercise ball, call the telephone number
on the front cover of this manual.
To use the manual mode of the console, follow the
steps beginning on page 12. To use a cross trainer
program, see page 14.
IMPORTANT: If there is a sheet of clear plastic on
the face of the console, remove the plastic. To prevent damage to the walking platform, wear clean
athletic shoes while using the treadmill. The first
time the treadmill is used, observe the alignment of
the walking belt, and center the walking belt if necessary (see page 20).
Note: The console can display speed and distance in
either miles or kilometers. To find out which unit of
measurement is selected or to change the unit of measurement, see THE INFORMATION MODE on page
16. For simplicity, all instructions in this section refer to
miles.
11
HOW TO TURN ON THE POWER
3.
IMPORTANT: If the treadmill has been exposed to
cold temperatures, allow it to warm to room temperature before turning on the power. If you do not
do this, the console displays or other electrical
components may become damaged.
Plug in the power cord
(see page 10). Next, locate
the reset/off circuit breaker
on the treadmill frame near
the power cord. Make sure
that the circuit breaker is in
the “reset” position.
To start the walking belt,
press the Start button,
the Speed increase button, or one of the speed
buttons numbered 1 to
10.
If the Start button or the Speed increase button is
pressed, the walking belt will begin to move at 1
mph. As you exercise, change the speed of the
walking belt as desired by pressing the Speed increase and decrease buttons. Each time you
press a button, the speed setting will change by
0.1 mph; if you hold down a button, the speed setting will change in increments of 0.5 mph. Note:
After you press the buttons, it may take a moment
for the walking belt to reach the selected speed setting.
Reset
Position
IMPORTANT: The console features a display demo
mode, designed to be used if the treadmill is displayed in a store. If the displays light as soon as
you plug in the power cord and switch the circuit
breaker to the reset position, the demo mode is
turned on. To turn off the demo mode, see THE INFORMATION MODE on page 16 to turn off the
demo mode.
If you press one of the numbered speed buttons,
the walking belt will gradually change speed until it
reaches the selected speed setting.
Next, stand on the foot rails of the treadmill. Locate the
clip attached to the key (see the drawing on page 11),
and slide the clip securely onto the waistband of your
clothes. Then, insert the key into the console. After a
moment, the displays will light. IMPORTANT: In an
emergency situation, the key can be pulled from
the console, causing the walking belt to slow to a
stop. Test the clip by carefully taking a few steps
backward; if the key is not pulled from the console,
adjust the position of the clip.
To stop the walking belt, press the Stop button.
The time will begin to flash in the display. To
restart the walking belt, press the Start button, the
Speed increase button, or one of the numbered
speed buttons.
4.
Change the incline of the treadmill as desired.
To change the incline of
the treadmill, press the
Incline increase and decrease buttons. Each
time you press a button,
the incline will change by
0.5%. Note: After you press the buttons, it may
take a moment for the treadmill to reach the selected incline setting.
HOW TO USE THE MANUAL MODE
1.
Start the walking belt.
Insert the key into the console.
See HOW TO TURN ON THE POWER above.
5.
2.
Follow your progress with the display.
Select the manual mode.
When you
select the
manual
mode, the
display will
Track
show a track
that represents 1/4 mile. As you walk or run, indicators will
appear in succession around the track until the entire track appears. The track will then disappear
and the indicators will again begin to appear in
succession.
When the
key is inserted, the
manual
mode will be
Track
selected. If
a program
has been selected, reselect the manual mode by
pressing any of the three Programs buttons repeatedly until a track appears in the display.
12
handrail—avoid moving your hands. When your
pulse is detected, one or two dashes will appear in
the right side of the display and then your heart
rate will be shown. For the most accurate heart
rate reading, continue to hold the contacts for
about 15 seconds.
The left side of the display
will show the elapsed
time, the distance that
you have walked or run,
and the incline level of the
treadmill. Note: When a
program is selected, the display will show the time
remaining in the program instead of the elapsed
time.
7. Turn on the fan if desired.
The fan features low and high speed settings.
Press the Fan button repeatedly to select a fan
speed or to turn off the fan. Note: If the fan is on
when the walking belt is stopped, the fan will turn
off automatically after a few minutes.
The right side of the display will show the approximate number of
calories you have
burned while walking or
running, the speed of the
walking belt, and your pace in minutes per mile.
The right side of the display will also show your
heart rate when you use the handgrip pulse sensor
or the optional chest pulse sensor.
8. When you are finished exercising, remove the
key from the console.
Step onto the foot rails, press the Stop button, and
adjust the incline of the treadmill to the lowest
setting. The incline must be at the lowest setting
when you fold the treadmill to the storage position, or you may damage the treadmill. Next, remove the key from the console and put it in a secure
place.
To reset the display, press the Stop button, remove
the key, and then reinsert the key.
6. Measure your heart rate if desired.
Note: If you use the handgrip pulse sensor and
the optional chest pulse sensor at the same
time, the console will not display your heart
rate accurately.
When you are finished using the treadmill, switch
the reset/off circuit breaker to the “off” position and
unplug the power cord. IMPORTANT: If you do
not do this, the treadmill’s electrical components may wear prematurely.
Before using the handgrip pulse sensor, remove
the sheets of clear plastic from the metal contacts.
In addition, make sure that your hands are clean.
To measure
your heart
rate, stand
on the foot
rails and
hold the
metal contacts on the
Contacts
13
HOW TO USE A CROSS TRAINER PROGRAM
During the
program, the
profile will
show your
Current Segment
progress. The
flashing segment of the
profile represents the current segment of the program. The height of the flashing segment indicates
the speed setting for the current segment. At the
end of each segment, a series of tones will sound
and the next segment of the profile will begin to
flash. If a different speed or incline setting is programmed for the next segment, the speed or incline
setting will flash in the display to alert you.
1. Insert the key into the console.
See HOW TO TURN ON THE POWER on page
12.
2. Select one of the six cross trainer programs.
To select a
cross trainer
program,
press one of
the three
Programs
buttons repeatedly
until “P 1,”
“P 2,” “P 3,” “P 4,” “P 5,” or “P 6” appears in the
display. When a cross trainer program is selected,
the program time will appear in the display, the
maximum incline setting of the program and the
maximum speed setting of the program will flash in
the display for a few seconds, and a profile of the
speed settings of the program will scroll across the
matrix in the display.
The program will continue in this way until the last
segment of the profile flashes in the display and
the last segment ends. The walking belt will then
slow to a stop.
If the speed or incline setting for the current segment is too high or too low, you can manually override the setting by pressing the Speed and Incline
buttons. Every few times a Speed button is
pressed, an additional indicator will appear or disappear in the Current Segment column. However,
when the current segment of the program ends,
the treadmill will automatically adjust to the
speed and incline settings for the next segment.
3. Press the Start button or the Speed increase
button to start the program.
A moment after you press the button, the treadmill
will automatically adjust to the first speed and incline settings of the program. Hold the handrails
and begin walking.
To stop the program at any time, press the Stop
button. To restart the program, press the Start button or the Speed increase button. The walking belt
will begin to move at 1 mph. When the next segment of the program begins, the treadmill will automatically adjust to the speed and incline settings for
that segment.
Each program is divided into 25, 30, or 45 oneminute segments. One speed setting and one incline setting are programmed for most segments.
Note: The same speed setting and/or incline setting
may be programmed for two or more consecutive
segments. During other segments, the console will
prompt you to perform strength exercises.
14
4. Perform the first strength exercise when
prompted.
repetitions with your right arm and half the repetitions with your left arm. The strength exercises require the use of dumbbells and an inflatable exercise ball (not included). To purchase dumbbells
or an exercise ball, call the telephone number
on the front cover of this manual.
When the
first strength
exercise
segment begins (only
one indicator
will flash in
the Current Segment column), the walking belt will
slow to a stop and the name of the first strength
exercise will appear in the display for a few seconds.
5. Continue the cross trainer program.
When you have performed the recommended number of repetitions, the words PRESS START will
appear in the display. To continue the cross trainer
program, step onto the treadmill, slide the clip
back onto the waistband of your clothes, and
press the Start button. The treadmill will automatically adjust to the speed and incline settings for the
next segment.
Next, the
display will
show the
recommended
number of
repetitions
for the first strength exercise.
The program will continue in this way until the last
segment ends. The walking belt will then slow to a
stop.
6. Follow your progress with the display.
See step 5 on pages 12 and 13.
Remove the clip from the waistband of your
clothes, step off the treadmill, and prepare to begin
the first strength exercise. Every few seconds, the
console will sound a tone; when a tone sounds,
perform one repetition of the exercise. Exercise
with a slow, steady motion; do not perform more
than one repetition each time a tone sounds. The
display will count down the repetitions as you perform them.
7. Measure your heart rate if desired.
See step 6 on page 13.
8. Turn on the fan if desired.
See step 7 on page 13.
9. When you are finished exercising, remove the
key from the console.
Note: Refer to the accompanying exercise chart to
see the correct form for each exercise. When performing lunges, alternate legs with each repetition.
When performing dumbbell rows, perform half the
See step 8 on page 13.
15
THE INFORMATION MODE
THE OPTIONAL CHEST PULSE SENSOR
The console features an information mode that keeps
track of treadmill usage information. The information
mode also allows you to select miles or kilometers as
the unit of measurement and to turn on and turn off the
demo mode.
An optional chest pulse sensor offers hands-free operation as it tracks your heart rate during your workouts.
To purchase the optional chest pulse sensor, call
the telephone number on the front cover of this
manual.
To select the information mode, hold down the Stop
button, insert the key into the console, and then release
the Stop button. When the information mode is selected, the following information will appear in the display:
The center of
the display will
show the total
number of hours
that the treadmill
has been operated. The lower
part of the display will show
total number of miles or kilometers that the walking belt
has moved. In addition, an “E” for English miles or an
“M” for metric kilometers will appear in the lower part of
the display. To change the unit of measurement, press
the Speed increase button.
Note: The console features a display demo mode, designed to be used if the treadmill is displayed in a
store. While the demo mode is turned on, the console
will function normally when you plug in the power cord,
switch the reset/off circuit breaker to the reset position,
and insert the key into the console. However, when
you remove the key, the displays will remain lit, although the buttons will not function. If the demo mode
is turned on, a “d” will appear in the display while the information mode is selected. To turn on or turn off the
demo mode, press the Speed decrease button.
To exit the information mode, remove the key from the
console.
16
HOW TO FOLD AND MOVE THE TREADMILL
HOW TO FOLD THE TREADMILL FOR STORAGE
Before folding the treadmill, adjust the incline to the
lowest position. If you do not do this, you may damage the
treadmill when you fold it. Next, unplug the power cord.
CAUTION: You must be able to safely lift 45 lbs. (20 kg) to
raise, lower, or move the treadmill.
1. Hold the metal frame firmly in the location shown by the
arrow at the right. CAUTION: To decrease the possibility
of injury, do not lift the frame by the plastic foot rails.
Make sure to bend your legs and keep your back straight.
As you raise the frame, make sure to lift with your legs
rather than with your back. Raise the frame about halfway
to the vertical position.
Frame
2. Move your right hand to the position shown and hold the
treadmill firmly. Using your left hand, pull the latch knob to
the left and hold it. Raise the frame until the latch pin is
aligned with the gap between the frame and the foot rail.
Slowly release the latch knob. Make sure that the latch pin
is fully inserted between the frame and the foot rail.
To protect the floor or carpet from damage, place a mat
under the treadmill. Keep the treadmill out of direct sunlight. Do not leave the treadmill in the storage position in
temperatures above 85° F (30° C).
Frame
Latch Knob
Latch Pin
HOW TO MOVE THE TREADMILL
Before moving the treadmill, convert the treadmill to the storage
position as described above. Make sure that the latch pin is
fully inserted between the frame and the foot rail.
1. Hold the upper ends of the handrails. Place one foot against
one of the wheels.
Handrail
2. Tilt the treadmill backward until it rolls freely on the front
wheels. Carefully move the treadmill to the desired location.
To reduce the risk of injury, use extreme caution while
moving the treadmill. Do not move the treadmill over an
uneven surface.
Wheel
3. Place one foot against one of the wheels, and carefully lower
the treadmill until it is resting in the storage position.
17
Engaged
HOW TO LOWER THE TREADMILL FOR USE
1. Hold the upper end of the treadmill with your right hand. Pull
the latch knob to the left and hold it. Pivot the frame downward until the frame is past the latch pin. Then, slowly release the latch knob.
Frame
Open
Latch Knob
Latch Pin
2. Hold the metal frame firmly with both hands, and lower it to
the floor. CAUTION: To decrease the possibility of injury, do
not lower the frame by gripping only the plastic foot rails.
Do not drop the frame to the floor. Make sure to bend your
legs and keep your back straight.
Frame
18
TROUBLESHOOTING
Most treadmill problems can be solved by following the steps below. Find the symptom that applies, and
follow the steps listed. If you need further assistance, please call the telephone number on the front
cover of this manual.
PROBLEM: The power does not turn on
SOLUTION: a. Make sure that the power cord is plugged into a surge suppressor, and that the surge suppressor
is plugged into a properly grounded outlet (see page 10). Use only a single-outlet surge suppressor that meets all of the specifications described on page 10. IMPORTANT: The treadmill is not
compatible with GFCI-equipped outlets.
b. After the power cord has been plugged in, make sure that the key is inserted into the console.
c. Check the reset/off circuit breaker located on the
treadmill frame near the power cord. If the switch
protrudes as shown, the circuit breaker has
tripped. To reset the circuit breaker, wait for five
minutes, and then press the switch back in.
c
Reset
Tripped
PROBLEM: The power turns off during use
SOLUTION: a. Check the reset/off circuit breaker (see the drawing above). If the circuit breaker has tripped, wait
for five minutes and then press the switch back in.
b. Make sure that the power cord is plugged in. If the power cord is plugged in, unplug it, wait for
five minutes, and then plug it back in.
c. Remove the key from the console. Reinsert the key into the console.
d. If the treadmill still will not run, see the front cover of this manual.
PROBLEM: The incline of the treadmill does not change correctly
SOLUTION: a. With the key in the console, press one of the Incline buttons. While the incline is changing, remove the key. After a few seconds, re-insert the key. The treadmill will automatically rise to the
maximum incline level and then return to the minimum level. This will recalibrate the incline system.
PROBLEM: The console displays remain lit when you remove the key from the console
SOLUTION: a. The console features a display demo mode, designed to be used if the treadmill is displayed in a
store. If the displays remain lit when you remove the key, the demo mode is turned on. To turn off
the demo mode, hold down the Stop button for a few seconds. If the displays are still lit, see THE
INFORMATION MODE on page 16 to turn off the demo mode.
PROBLEM: The display of the console does not function properly
SOLUTION: a. Remove the key from the console and UNPLUG THE
POWER CORD. Remove the three Hood Screws (7).
Carefully pivot the Hood (41) off.
a
7
41
19
Locate the Reed Switch (63) and the Magnet (46) on
the left side of the Front Roller (47). Turn the Front
Roller until the Magnet is aligned with the Reed Switch.
Make sure that the gap between the Magnet and
the Reed Switch is about 1/8 in. (3 mm). If necessary, loosen the 3/4" Screw (7), move the Reed Switch
slightly, and retighten the Screw. Reattach the Hood
(41) (not shown), making sure that the Hood Screws
(7) (not shown) are inserted into the same holes from
which they were removed. Run the treadmill for a few
minutes to check for a correct speed reading.
Top
View
1/8 in.
7
47
46
63
PROBLEM: The walking belt slows when walked on
SOLUTION: a. Use only a single-outlet surge suppressor that meets all the specifications described on page 10.
b. If the walking belt is overtightened, treadmill performance may decrease and the walking belt may become damaged. Remove the key and UNPLUG THE
POWER CORD. Using the hex key, turn both rear
roller bolts counterclockwise, 1/4 of a turn. When the
walking belt is properly tightened, you should be able
to lift each edge of the walking belt 2 to 3 in. (5 to 8
cm) above the walking platform. Be careful to keep
the walking belt centered. Then, plug in the power
cord, insert the key, and run the treadmill for a few
minutes. Repeat until the walking belt is properly tightened.
b
2–3 in.
Rear Roller Bolts
c. If the walking belt still slows when walked on, please see the front cover of this manual.
PROBLEM: The walking belt is off-center or slips when walked on
SOLUTION: a. If the walking belt is off-center, first remove the key
and UNPLUG THE POWER CORD. If the walking
belt has shifted to the left, use the hex key to turn
the left rear roller bolt clockwise 1/2 of a turn; if the
walking belt has shifted to the right, turn the left
bolt counterclockwise 1/2 of a turn. Be careful not to
overtighten the walking belt. Then, plug in the power
cord, insert the key, and run the treadmill for a few
minutes. Repeat until the walking belt is centered.
b. If the walking belt slips when walked on, first remove the key and UNPLUG THE POWER CORD.
Using the hex key, turn both rear roller bolts clockwise, 1/4 of a turn. When the walking belt is correctly
tightened, you should be able to lift each edge of the
walking belt 2 to 3 in. (5 to 8 cm) above the walking
platform. Be careful to keep the walking belt centered.
Then, plug in the power cord, insert the key, and carefully walk on the treadmill for a few minutes. Repeat
until the walking belt is properly tightened.
20
a
b
EXERCISE GUIDELINES
Burning Fat—To burn fat effectively, you must exercise at a low intensity level for a sustained period of
time. During the first few minutes of exercise, your
body uses carbohydrate calories for energy. Only after
the first few minutes of exercise does your body begin
to use stored fat calories for energy. If your goal is to
burn fat, adjust the intensity of your exercise until your
heart rate is near the lowest number in your training
zone. For maximum fat burning, exercise with your
heart rate near the middle number in your training
zone.
WARNING: Before beginning any
exercise program, consult your physician.
This is especially important for persons over
the age of 35 or persons with pre-existing
health problems.
The pulse sensor is not a medical device.
Various factors may affect the accuracy of
heart rate readings. The pulse sensor is intended only as an exercise aid in determining
heart rate trends in general.
Aerobic Exercise—If your goal is to strengthen your
cardiovascular system, you must perform aerobic exercise, which is activity that requires large amounts of
oxygen for prolonged periods of time. For aerobic exercise, adjust the intensity of your exercise until your
heart rate is near the highest number in your training
zone.
These guidelines will help you to plan your exercise
program. For detailed exercise information, obtain a
reputable book or consult your physician. Remember,
proper nutrition and adequate rest are essential for
successful results.
WORKOUT GUIDELINES
EXERCISE INTENSITY
Warming up—Start with 5 to 10 minutes of stretching
and light exercise. A warm-up increases your body
temperature, heart rate, and circulation in preparation
for exercise.
Whether your goal is to burn fat or to strengthen your
cardiovascular system, exercising at the proper intensity is the key to achieving results. You can use your
heart rate as a guide to find the proper intensity level.
The chart below shows recommended heart rates for
fat burning and aerobic exercise.
Training Zone Exercise—Exercise for 20 to 30 minutes with your heart rate in your training zone. (During
the first few weeks of your exercise program, do not
keep your heart rate in your training zone for longer
than 20 minutes.) Breathe regularly and deeply as you
exercise–never hold your breath.
Cooling down—Finish with 5 to 10 minutes of stretching. Stretching increases the flexibility of your muscles
and helps to prevent post-exercise problems.
EXERCISE FREQUENCY
To find the proper intensity level, find your age at the
bottom of the chart (ages are rounded off to the nearest ten years). The three numbers listed above your
age define your “training zone.” The lowest number is
the heart rate for fat burning, the middle number is the
heart rate for maximum fat burning, and the highest
number is the heart rate for aerobic exercise.
To maintain or improve your condition, complete three
workouts each week, with at least one day of rest between workouts. After a few months of regular exercise, you may complete up to five workouts each
week, if desired. Remember, the key to success is to
make exercise a regular and enjoyable part of your
everyday life.
21
SUGGESTED STRETCHES
The correct form for several basic stretches is shown at the right. Move slowly as you stretch—never bounce.
1. Toe Touch Stretch
Stand with your knees bent slightly and slowly bend forward from
your hips. Allow your back and shoulders to relax as you reach
down toward your toes as far as possible. Hold for 15 counts, then
relax. Repeat 3 times. Stretches: Hamstrings, back of knees and
back.
1
2. Hamstring Stretch
Sit with one leg extended. Bring the sole of the opposite foot toward
you and rest it against the inner thigh of your extended leg. Reach
toward your toes as far as possible. Hold for 15 counts, then relax.
Repeat 3 times for each leg. Stretches: Hamstrings, lower back and
groin.
2
3. Calf/Achilles Stretch
With one leg in front of the other, reach forward and place your
hands against a wall. Keep your back leg straight and your back foot
flat on the floor. Bend your front leg, lean forward and move your
hips toward the wall. Hold for 15 counts, then relax. Repeat 3 times
for each leg. To cause further stretching of the achilles tendons,
bend your back leg as well. Stretches: Calves, achilles tendons and
ankles.
3
4
4. Quadriceps Stretch
With one hand against a wall for balance, reach back and grasp one
foot with your other hand. Bring your heel as close to your buttocks
as possible. Hold for 15 counts, then relax. Repeat 3 times for each
leg. Stretches: Quadriceps and hip muscles.
5. Inner Thigh Stretch
Sit with the soles of your feet together and your knees outward. Pull
your feet toward your groin area as far as possible. Hold for 15
counts, then relax. Repeat 3 times. Stretches: Quadriceps and hip
muscles.
22
5
PART LIST—Model No. WLTL49907.0
R0707A
To locate the parts listed below, see the EXPLODED DRAWING near the end of this manual.
Key No. Qty.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
2
3
29
1
10
2
12
8
2
2
4
2
1
2
2
1
1
1
1
1
1
2
1
2
2
1
1
2
2
2
2
6
9
1
2
1
1
1
1
1
1
1
1
2
1
1
1
1
1
1
1
1
2
1
1
1
Description
Foot Rail Decal
3/4" Belly Pan Screw
Screw
Reset/Off Circuit Breaker
Foot Rail Screw
Isolator
3/4" Screw
Star Washer
Platform Bolt, Back
Platform Bolt, Front
Belt Guide Screw
Belt Guide
Power Cord Grommet
Front Endcap Screw
Frame Pivot Bolt
Left Foot Rail
Right Foot Rail
Motor Clevis Pin
Motor Bracket
Handrail
Latch Pin Assembly
Motor Washer
Motor Star Washer
Motor Bolt
Motor Tension Bolt
Motor Belt
Drive Motor
Frame Spacer
Endcap Base Pad
Motor Nut
Lift Frame Bolt
Lock Nut
Ground Screw
Console
Fan Screw
Power Cord
Console Fan
Controller
Electronic Bracket
Filter Wire
Hood
Front Roller Bushing
Lift Frame
Front Endcap
Front Roller Bolt
Magnet
Front Roller
Walking Belt
Walking Platform
Incline Motor/Controller Wire
Rear Roller
Left Rear Endcap
Rear Roller Bolt
Right Rear Endcap
Hex Key
Incline Stop Bracket
Key No. Qty.
Description
57
1
Base Ground Wire
58
1
Frame
59
1
Belly Pan
60
4
U-nut
61
1
Reed Switch Clip
62
2
Handrail Endcap
63
1
Reed Switch
64
4
Handrail Bolt
65
2
2.5" Extension Leg Bolt
66
2
Star Washer
67
2
Extension Leg Nut
68
2
Caution Decal
69
1
Warning Decal
70
2
Platform Nut
71
9
Cable Tie
72
1
Lower Incline Motor Bolt
73
1
Latch Housing
74
2
Rear Roller Lock Washer
75
1
Releasable Tie
76
1
Access Door
77
1
Wire Harness
78
2
Extension Leg Endcap
79
1
Key/Clip
80
2
Front Wheel
81
2
Wheel Pin
82
2
Base Pad
83
4
1" Tek Screw
84
1
Upright
85
1
Console Base
86
1
Upper Incline Motor Bolt
87
1
Hair Pin Cotter Pin
88
1
Incline Motor
89
2
Extension Leg
90
2
Rear Roller Bracket
91
2
Rear Roller Flat Washer
92
2
2.25" Extension Leg Bolt
Optic Disk
93
1
Photo Switch Nut
1
94
Rear Roller Bracket Screw
2
95
96
1
Photo Switch
97
1
Photo Switch Bolt
98
3
Hood Clip
99
1
Latch Plate
100
10
Wire Tie
101
1
Roller Ground Wire
102
1
Photo Switch Wire
103
1
Front Roller Nut
#10 x 3/4" Screw
104
1
*
–
4" Blue Wire, 2F
*
–
10" Red Wire, M/F
*
–
12" Blue Wire, 2F
*
–
8" Black Wire, M/F
12" Blue Wire, M/F
–
*
–
User’s Manual
*
*These parts are not illustrated.
Specifications are subject to change without notice.
23
5
24
55
91
95
74
90
53
16
5
3
9
52
69
5
6
1
53
49
99
74
3
91
51
95
7
12
5
3
48
11
9
54
90
7
5
15
5
70 10
58
5
17
7
47
7
46
6
5
11
10
12
5
70
1
15
5
EXPLODED DRAWING A—Model No. WLTL49907.0
R0707A
EXPLODED DRAWING B—Model No. WLTL49907.0
R0707A
7
98
7
41
98
7
98
2
4
104
59
30
23
30
2
24
40
26
2
27
36
19
63
7
25
22
13
61
28
101
43
33
50
33
32
42
87
22
25
38
45
33
66
18
33
103
39
28
32
25
EXPLODED DRAWING C—Model No. WLTL49907.0
R0707A
8
3
64
8
3
20
3
8
64
60
62
3
3
8
3
3
3
73
77
3
3
60
84
62
21
14
33
57
44
92
32
31
31
8
32
82
68
77
14
83
44
78
8
92
86
89
67
32
65
8
88
81
29
80
72
94
66
96
97
83
32
56
93
102
82
89
83
68
8
81
67
80
29
78
83
26
65
EXPLODED DRAWING D—Model No. WLTL49907.0
37
35
35
34
79
33
85
3
3
76
3
3
3
7
100
71
75
100
27
R0707A
ORDERING REPLACEMENT PARTS
To order replacement parts, please see the front cover of this manual. To help us assist you, be prepared to provide the following information when contacting us:
• the model number and serial number of the product (see the front cover of this manual)
• the name of the product (see the front cover of this manual)
• the key number and description of the replacement part(s) (see the PART LIST and the EXPLODED
DRAWING near the end of this manual)
LIMITED WARRANTY
ICON Health & Fitness, Inc. (ICON) warrants this product to be free from defects in workmanship and
material under normal use and service conditions. The drive motor is warranted for ten (10) years after
the date of purchase. Parts and labor are warranted for ninety (90) days after the date of purchase.
This warranty extends only to the original purchaser. ICON's obligation under this warranty is limited to
replacing or repairing, at ICON's option, the product through one of its authorized service centers. All repairs for which warranty claims are made must be pre-authorized by ICON. If the product is shipped to a
service center, freight charges to and from the service center will be the customer’s responsibility. For inhome service, the customer will be responsible for a minimal trip charge. This warranty does not extend
to any product or damage to a product caused by or attributable to freight damage, abuse, misuse, improper or abnormal usage or repairs not provided by an ICON authorized service center; products used
for commercial or rental purposes; or products used as store display models. No other warranty beyond
that specifically set forth above is authorized by ICON.
ICON is not responsible or liable for indirect, special or consequential damages arising out of or in connection with the use or performance of the product or damages with respect to any economic loss, loss
of property, loss of revenues or profits, loss of enjoyment or use, costs of removal or installation or other
consequential damages of whatsoever nature. Some states do not allow the exclusion or limitation of incidental or consequential damages. Accordingly, the above limitation may not apply to you.
The warranty extended hereunder is in lieu of any and all other warranties and any implied warranties of
merchantability or fitness for a particular purpose is limited in its scope and duration to the terms set
forth herein. Some states do not allow limitations on how long an implied warranty lasts. Accordingly, the
above limitation may not apply to you.
This warranty gives you specific legal rights. You may also have other rights which vary from state to state.
ICON HEALTH & FITNESS, INC., 1500 S. 1000 W., LOGAN, UT 84321-9813
Part No. 255791 R0707A
Printed in USA © 2007 ICON IP, Inc.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising