Slip-On (2010

Slip-On (2010
Installation Instructions
1. Make sure the bike is completely cool before starting the
installation. Make sure the bike is secure on its sidestand
or ideally a service lift.
6. Remove OEM muffler assembly.
2. Remove the main seat assembly.
V.A.L.E.
TM
2010 Honda
V a r i a b l e
A x i s
L o c k i n g
E x h a u s t
VFR1200F
V.A.L.E.™ Slip-on Exhaust System with M-2/M-5 Canister
Part # 005-2870406V / 005-2870407V / 005-2870408V / 005-2870419V / 005-2870420V
3. Remove right side rear cover by removing the 2 bolts
from the top and the push pin from the lower, pull
outward.
7. Loosely attach the V.A.L.E.TM muffler to the stainless steel
V.A.L.E.TM connector tube using the supplied 6x20mm
socket head cap screws and 6mm split washers.
Muffler Inlet
X-Lite™ Ring
Slip Tube
Parts List
Qty. Description
Part Number
1
1
1
1
1
1
1
Varies
005-28704S
005-287-3
005-7-2-3KIT
Varies
005-27-61MSH
015-10212
M-2/5 Muffler Canister Slip-On Tube Assembly HARDWARE KIT
X-Ring Kit
Canister Clamp
Barrel Clamp
TBR Sticker Kit
4. Rotate servo wheel (by hand) to remove tension from
cable and remove cable from servo. Be gentle so
damage does not occur to internal gears of servo.
8. Slide barrel clamp on end of TBR slip-tube and install
loosely on motorcycle.
IMPORTANT - PLEASE READ CAREFULLY
This exhaust system has not been tested with aftermarket or OEM accessories and
is not designed to work with them. (i.e. hard bags/ centerstand/ lisc. plate frames)
We recommend that this performance part be installed by a qualified motorcycle
technician. If you have any doubts as to your ability to install this performance
part, please consult with your local motorcycle dealer. Read all instructions first
before starting installation. Make sure the motorcycle and exhaust system are
completely cool before starting the installation. Also, make sure the bike is secure
on a centerstand or ideally a service lift during installation. Be sure to save all
stock components for possible use later.
V.A.L.E.™ Assembly Detail
5. Rotate servo back to its original location.
Installation Instructions
9. Slide rubber lined muffler clamp over muffler and
attach to inside of rear passanger foot rest using OEM
hardware. Tighten X-ring, then muffler mount then
barrel clamp.
2010 Honda
V.A.L.E.
TM
V a r i a b l e
A x i s
L o c k i n g
E x h a u s t
VFR1200F
12. Before you run the bike, clean off all fingerprints and
dirt, as any oily residue will etch the metal and become
somewhat permanent when the system gets hot. Run
the bike and enjoy. It is normal for some white smoke to
appear the first time you start the bike. This is packing/
manufacturing oil from inside the pipe burnin g off.
Check for gaps or leaks. If you find a leak, a little high
temperature silicon sealant should fix it. After 50 to 100
miles, recheck all fasteners for tightness.
V.A.L.E.™ Slip-on Exhaust System with M-2/M-5 Canister
Part # 005-2870406V / 005-2870407V / 005-2870408V / 005-2870419V / 005-2870420V
005-2060407V
Care & Cleaning
Care & Cleaning
Keep system free of dirt and moisture. Store in a cool, dry place. Make sure vehicle is
completely cool before maintenance.
Stainless Header System: Polished stainless steel pipes will turn a light golden hue
after a few heat cycles, this is a normal characteristic of high quality stainless steel.
Clean using a mild water based spray cleaner. Always apply cleaner or polish with a soft,
clean cloth.
Titanium Header System: Polished titanium pipes will experience color shift ranging
from deep blue/purple through amber after a few heat cycles. This is a normal
characteristic of high quality titanium. Clean using a mild water based spray cleaner.
Always apply cleaner or polish with a soft, clean cloth.
Polished Aluminum Canisters: Use an aluminum or mag wheel polish to restore the
bright finish to factory spec.
Brushed Aluminum Canisters: Clean using a mild water based spray cleaner. Always
apply cleaner or polish with a soft, clean cloth.
Carbon Fiber Canisters: Clean using a mild water based spray cleaner. Always apply
cleaner or polish with a soft, clean cloth. Always make sure the fiberglass packing inside
is in good condition and not burned out, as exhaust heat inside an empty canister will
deteriorate the carbon fiber sleeve.
TBR sells repack kits (Road - #005-10038, Offroad - #005-10038MX) that include
everything you need to easily do it yourself.
Titanium Mufflers: For cleaning use a mild water based spray cleaner. Always apply
cleaner or polish with a soft, clean cloth. Always make sure the fiberglass packing inside
is in good condition and not burned out, as exhaust heat inside an empty canister will
deteriorate the carbon fiber sleeve.
TBR sells repack kits (Road - #005-10038, Offroad - #005-10038MX) that include
everything you need to easily do it yourself.
Qty. Description
Part Number
1
1
1
1
1
1
1
Varies
005-28704S
005-287-3
005-7-2-3KIT
Varies
005-27-61MSH
015-10212
M-2/5 Muffler Canister Slip-On Tube Assembly HARDWARE KIT
X-Ring Kit
Canister Clamp
Barrel Clamp
TBR Sticker Kit
Repack all road canisters every 3,000 miles. Part #005-10038
Repack all offroad canisters after every 10 hours of use. Part #005-10038MX
NEVER dyno test your bike with carbon fiber or titanium canisters installed - the
intense heat and lack of cooling air can quickly burn through the canister material. Two
Brothers Racing does not provide a warranty for burned canisters.
10. Re-install side cover and seat.
11. Check your work and clean all fingerprints
Warranty
Two Brothers Racing products are intended for closed course competition purposes only,
and therefore are sold “as is” without warranty. Two Brothers Racing specifically disclaims
any warranties of merchantability or fitness for a particular purpose and disclaims all
responsibility for consequential and incidental damages or any other losses arising from
the use of these products or parts.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement