DS PCA T5 EXCEL one4all lp xitec en

DS PCA T5 EXCEL one4all lp xitec en
T5, TCL
Electronic ballasts for dimming to 1 %
Linear lamps T5, 16 mm high efficiency, high output
PCA T5 EXCEL one4all lp
14–80 W 220–240 V 50/60/0 Hz
4,95
21
6
RoHS
side fixing feature
T
side fixing feature
Lamp
wattage
type
Ballast
type
T5
T5
T5
TC-L
T5
TC-L
T5
T5
T5
TC-L
T5
T5
T5
T5
T5
T5
T5
T5
T5
T5
T5
PCA 1x14/24 T5 EXCEL one4all lp X
PCA 2x14/24 T5 EXCEL one4all lp X
PCA 1x14/24 T5 EXCEL one4all lp X
PCA 1x14/24 T5 EXCEL one4all lp X
PCA 2x14/24 T5 EXCEL one4all lp X
PCA 2x14/24 T5 EXCEL one4all lp X
PCA 1x21/39 T5 EXCEL one4all lp X
PCA 2x21/39 T5 EXCEL one4all lp X
PCA 1x21/39 T5 EXCEL one4all lp X
PCA 1x21/39 T5 EXCEL one4all lp X
PCA 2x21/39 T5 EXCEL one4all lp X
PCA 1x28/54 T5 EXCEL one4all lp X
PCA 2x28/54 T5 EXCEL one4all lp X
PCA 1x28/54 T5 EXCEL one4all lp X
PCA 2x28/54 T5 EXCEL one4all lp X
PCA 1x35/49/80 T5 EXCEL one4all lp X
PCA 2x35/49 T5 EXCEL one4all lp X
PCA 1x35/49/80 T5 EXCEL one4all lp X
PCA 2x35/49 T5 EXCEL one4all lp X
PCA 1x35/49/80 T5 EXCEL one4all lp X
PCA 2/80 T5 EXCEL one4all lp 3
PH
W
1x14
2x14
1x24
1x24
2x24
2x24
1x21
2x21
1x39
1x40
2x39
1x28
2x28
1x54
2x54
1x35
2x35
1x49
2x49
1x80
2x80
U
D
•integrated SMART interface
•Intelligent Voltage Guard (overvoltage indication and
undervoltage shutdown)
•Intelligent Temperature Guard
(overtemperature protection)
•automatically triggered adjustable emergency
light value for DC and rectified AC voltage
•SMART Heating Concept for optimum filament
heating at any dimming level and cut off the
electrodes at approx. 90 % dimmlevel for maximum
energy efficiency
•plugADDRESSING
Extensive feedback functions and adjustable
parameters:
•OEM-specific reserved memory for storing customer
data in the ballast
•extensive diagnostic options
AS
E
•world first: first processor-controlled ballast with
x inside
•operation of T5 lamps of the same length
(e.g. FH 28 W / FQ 54 W)
•automatic lamp detection and operation with correct
lamp parameters
•average service life = 50,000 h (at ta max. with a
failure rate ≤ 0.2 % per 1,000 operating hours)
•dimming range from 1–100 %
•lamp friendly warm start within 0.5 s with AC and
0.2 s with DC
•power consumption in standby mode < 0.5 W
•disturbance free precise control with a digital signal
(DSI), switchDIM or DALI (Digital Addressable
Lighting Interface)
•fully digital lamp management for flash-free starting
at any dimming level
•operating frequency ~40–100 kHz
O
4,1
30
4,1
L
D
article
number
22176178
22176179
22176178
22176178
22176179
22176179
22176176
22176177
22176176
22176176
22176177
22176174
22176175
22176174
22176175
22176172
22176173
22176172
22176173
22176172
22176053
length
L
mm
360
360
360
360
360
360
360
425
360
360
425
360
425
360
425
360
425
360
425
360
425
fixing
centres
D mm
350
350
350
350
350
350
350
415
350
350
415
350
415
350
415
350
415
350
415
350
415
weight
kg
0.25
0.28
0.25
0.25
0.28
0.28
0.25
0.35
0.25
0.25
0.35
0.26
0.35
0.26
0.35
0.27
0.34
0.27
0.34
0.37
0,35
circuit
power
W2
16.3
31.7
25.8
25.5
52.1
51.5
23.8
46.0
42.3
42.6
84.1
30.9
62.1
59.5
118.4
38.8
76.4
53.7
105.6
86.9
164,5
•the emergency light value can be set between
1 % and 100 %
•backwards compatibility adjustable
•DALI-MEMORY and corridorFUNCTION
with 3 preprogrammed profiles
Packaging:
360 mm housing
box of 10
76 boxes/pallet
760 pieces/pallet
425 mm housing
box of 25
33 boxes/pallet
825 pieces/pallet
lamp
power
W2
14
2x14
23
22
2x23
2x22
21
2x21
38
40
2x38
28
2x28
54
2x54
35
2x35
49
2x49
80
2x80
λ
current
at 230 V / 50 Hz at 230 V / 50 Hz
A2
0.08
0.95
0.15
0.97
0.12
0.97
0.12
0.97
0.23
0.98
0.23
0.98
0.11
0.95
0.21
0.97
0.20
0.97
0.19
0.97
0.38
0.99
0.15
0.95
0.28
0.97
0.27
0.98
0.53
0.99
0.18
0.97
0.33
0.97
0.24
0.97
0.47
0.98
0.39
0.98
0,75
0,99
1 10 °C to ta max: normal diming operation
-25 °C to +10 °C: dimming operation from 100 % to 30 %.
-25 °C to +10 °C, dimming below 30 %: Ballast could shut down but will not cause failure. This applies to AC and DC operation.
2 valid at 100 % light output
3 single wattage ballast, corridorFUNCTION V1, power consumption in standby mode <0.5 W (< 0.8 W by switchDIM, DSI and corridorFUNCTION)
Data sheet 09/11-789-3  We reserve the right to make technical changes without prior notice.
Standards:
EN 55015
EN 55022
EN 60929
EN 61000-3-2
EN 61347-2-3
EN 61547
Suitable for emergency
installations according
to EN 50172
tc point
°C
80
80
80
80
85
85
85
80
85
80
85
80
80
85
85
80
80
80
85
85
80
temperature
range
°C 1
-25 → +60
-25 → +60
-25 → +60
-25 → +60
-25 → +60
-25 → +60
-25 → +60
-25 → +60
-25 → +60
-25 → +60
-25 → +60
-25 → +60
-25 → +60
-25 → +60
-25 → +55
-25 → +60
-25 → +60
-25 → +60
-25 → +60
-25 → +60
-25 → +50
Electronic ballasts for dimming to 1 %
Linear lamps T5, 16 mm high efficiency, high output
2
3
4
+
–
DA
DA
Light output level in DC operation:
Programmable from 0 % to 100 %
Programming by extended DSI or DALI signal
(16 bit).
Default value is 70 %
In DC operation dimming mode can be activated.
PH
Emergency units:
The “PCA T5 EXCEL one4all lp x” ballasts are
compatible with all emergency units from Tridonic.
See the table in the data sheet. Also all “5-pole”
emergency units can be used. When used with other
emergency units tests are necessary.
Temperature range:
Unlimited dimming range from 10 °C to ta max.
-25 °C to +10 °C: dimming operation from 100 %
to 30 %. If dimm level goes below 30 % malfunction
possible, but no electronic ballast damage.
This applies to AC and DC operation.
Lamp type recognition:
Each of the lamps for wich the control gear is designed
will be operated correctly according the lamp
specifications. The currently used lamp is recognised
during the start up process.
To avoid an incorrect lamp recognition due to fast
multiple ON / OFF switches, new lamp data are only
restored if the lamp has operated for at least 5
seconds.
2
Mains current at
Un = 220 V DC
0.06 A
0.12 A
0.10 A / 0.10 A
0.20 A / 0.20 A
0.09 A
0.17 A
0.15 A / 0.15 A
0.30 A
0.11 A
0.21 A
0.21 A
0.42 A
0.14 A
0.26 A
0.18 A
0.36 A
0.30 A
0.79 A
Mains current at
Un = 240 V DC
0.06 A
0.12 A
0.09 A / 0.09 A
0.18 A / 0.18 A
0.08 A
0.16 A
0.14 A / 0.14 A
0.28 A
0.11 A
0.20 A
0.20 A
0.38 A
0.13 A
0.24 A
0.17 A
0.33 A
0.27 A
0.72 A
Ballast lumen factor AC operation (AC-BLF) EN 60929 8.1:
wattage
W
1x14
2x14
1x24 / 1x24
2x24 / 2x24
1x21
2x21
1x39 / 1x40
2x39
1x28
2x28
1x54
2x54
1x35
2x35
1x49
2x49
1x80
2x80
lamp
type
T5
T5
T5 / TC-L
T5 / TC-L
T5
T5
T5 / TC-L
T5
T5
T5
T5
T5
T5
T5
T5
T5
T5
T5
Ballast
type
PCA 1x14/24 T5 EXCEL one4all lp X
PCA 2x14/24 T5 EXCEL one4all lp X
PCA 1x14/24 T5 EXCEL one4all lp X
PCA 2x14/24 T5 EXCEL one4all lp X
PCA 1x21/39 T5 EXCEL one4all lp X
PCA 2x21/39 T5 EXCEL one4all lp X
PCA 1x21/39 T5 EXCEL one4all lp X
PCA 2x21/39 T5 EXCEL one4all lp X
PCA 1x28/54 T5 EXCEL one4all lp X
PCA 2x28/54 T5 EXCEL one4all lp X
PCA 1x28/54 T5 EXCEL one4all lp X
PCA 2x28/54 T5 EXCEL one4all lp X
PCA 1x35/49/80 T5 EXCEL one4all lp X
PCA 2x35/49 T5 EXCEL one4all lp X
PCA 1x35/49/80 T5 EXCEL one4all lp X
PCA 2x35/49 T5 EXCEL one4all lp X
PCA 1x35/49/80 T5 EXCEL one4all lp X
PCA 2/80 T5 EXCEL one4all lp
AS
E
6
7
Ballast
type
PCA 1x14/24 T5 EXCEL one4all lp X
PCA 2x14/24 T5 EXCEL one4all lp X
PCA 1x14/24 T5 EXCEL one4all lp X
PCA 2x14/24 T5 EXCEL one4all lp X
PCA 1x21/39 T5 EXCEL one4all lp X
PCA 2x21/39 T5 EXCEL one4all lp X
PCA 1x21/39 T5 EXCEL one4all lp X
PCA 2x21/39 T5 EXCEL one4all lp X
PCA 1x28/54 T5 EXCEL one4all lp X
PCA 2x28/54 T5 EXCEL one4all lp X
PCA 1x28/54 T5 EXCEL one4all lp X
PCA 2x28/54 T5 EXCEL one4all lp X
PCA 1x35/49/80 T5 EXCEL one4all lp X
PCA 2x35/49 T5 EXCEL one4all lp X
PCA 1x35/49/80 T5 EXCEL one4all lp X
PCA 2x35/49 T5 EXCEL one4all lp X
PCA 1x35/49/80 T5 EXCEL one4all lp X
PCA 2/80 T5 EXCEL one4all lp
D
Our ballasts are construed to operate DC voltage and
pulsed DC voltage.
To operate ballasts with pulsed DC voltage the polarity
is absolute mandatory.
lamp
type
T5
T5
T5 / TC-L
T5 / TC-L
T5
T5
T5 / TC-L
T5
T5
T5
T5
T5
T5
T5
T5
T5
T5
T5
T
DC operation:
220–240 V 0 Hz
198–280 V 0 Hz certain lamp start
176–280 V 0 Hz operating range
Use in emergency lighting installations according to
EN 50172 or for emergency luminaires according
to EN 61347-2-3 appendix J.
wattage
W
1x14
2x14
1x24 / 1x24
2x24 / 2x24
1x21
2x21
1x39 / 1x40
2x39
1x28
2x28
1x54
2x54
1x35
2x35
1x49
2x49
1x80
2x80
U
AC operation:
Mains voltage
220–240 V 50/60 Hz
198–264 V 50/60 Hz including safety
tolerance (±10 %)
202–254 V 50/60 Hz including performance
tolerance (+6 % / -8 %)
Mains currents in DC operation (at 70 % light output):
O
Lamp starting characteristics:
Warm start
Starting time 0.5 s with AC
Starting time 0.2 s with DC
Start at any dimming level
AC-BLF at
Un = 230 V AC
1.00
0.99
1.01 / 1.04
1.02 / 1.02
1.03
1.02
1.02 / 0.97
1.02
1.00
1.01
1.00
1.01
0.99
0.98
1.02
1.00
1.02
1.00
The ballast lumen factor for AC operation (AC-BLF) does not alter from Un = 198 V AC to Un = 254 V AC.
The ballast lumen factor for DC operation (DC-BLF) on the basis of an automatic power reduction of the ballasts
(default value is 70 %) will be smaller than AC. It does not alter in the DC operating range (198–280 V DC).
Harmonic distortion in the mains supply (at 230 V / 50 Hz):
wattage
W
1x14
2x14
1x24 / 1x24
2x24 / 2x24
1x21
2x21
1x39 / 1x40
2x39
1x28
2x28
1x54
2x54
1x35
2x35
1x49
2x49
1x80
2x80
lamp
type
T5
T5
T5 / TC-L
T5 / TC-L
T5
T5
T5 / TC-L
T5
T5
T5
T5
T5
T5
T5
T5
T5
T5
T5
Ballast
type
PCA 1x14/24 T5 EXCEL one4all lp X
PCA 2x14/24 T5 EXCEL one4all lp X
PCA 1x14/24 T5 EXCEL one4all lp X
PCA 2x14/24 T5 EXCEL one4all lp X
PCA 1x21/39 T5 EXCEL one4all lp X
PCA 2x21/39 T5 EXCEL one4all lp X
PCA 1x21/39 T5 EXCEL one4all lp X
PCA 2x21/39 T5 EXCEL one4all lp X
PCA 1x28/54 T5 EXCEL one4all lp X
PCA 2x28/54 T5 EXCEL one4all lp X
PCA 1x28/54 T5 EXCEL one4all lp X
PCA 2x28/54 T5 EXCEL one4all lp X
PCA 1x35/49/80 T5 EXCEL one4all lp X
PCA 2x35/49 T5 EXCEL one4all lp X
PCA 1x35/49/80 T5 EXCEL one4all lp X
PCA 2x35/49 T5 EXCEL one4all lp X
PCA 1x35/49/80 T5 EXCEL one4all lp X
PCA 2/80 T5 EXCEL one4all lp
THD
3
5
7
9
11
10.2
5.4
6.1
3.2
2.2
1.6
7.8
4.3
2.5
2.5
2.7
2.2
6.1 / 6.9 4.6 / 5.8 1.1 / 1.1 1.2 / 1.4 1.2 / 1.2 1.2 / 1.3
4.8 / 8.5 3.2 / 6.2 1.4 / 1.8 2.0 / 2.7 1.3 / 1.9 1.2 / 1.7
8.1
5.9
2.4
2.5
2.5
1.6
7.2
3.6
4.4
2.5
1.5
1.5
7.0 / 6.2 5.5 / 4.7 1.1 / 0.7 2.1 / 1.4 1.5 / 1.0 1.3 / 0.9
5.3
4.0
2.5
1.8
0.6
0.9
9.74
3.93
3.39
2.68
2.52
2.44
10.0
7.3
1.7
2.1
2.2
1.9
5.6
3.5
1.5
1.6
1.1
1.3
8.9
8.5
1.4
1.5
0.7
0.7
9.1
6.0
4.2
2.2
1.9
1.8
8.7
7.2
1.4
1.4
1.4
0.9
9.6
7.8
4.3
1.8
1.0
1.0
7.8
7.5
0.6
1.1
0.6
0.7
8.1
7.8
1.6
0.6
0.5
0.6
6.8
5.4
4.1
0.8
0.8
0.7
Data sheet 09/11-789-3  We reserve the right to make technical changes without prior notice.
Electronic ballasts for dimming to 1 %
Linear lamps T5, 16 mm high efficiency, high output
Dimming:
Dimming curve is adapted to the eye sensitiveness.
Dimming range 1 % to 100 %
Digital control with:
•DSI signal: 8 bit Manchester Code
Speed 1 % to 100 % in 1.4 s
•DALI signal: 16 bit Manchester Code
Maximum speed 1 % to 100 % in 550 ms
(adjustable between 50 ms and 90 s)
Programmable parameter:
Minimum dimming level
Maximum dimming level
Default minimum = 1 %
Default maximum = 100 %
Dimming characteristics
PCA T5 EXCEL one4all lp
Energy saving
PCA T5 EXCEL one4all lp
digital dimming value
mains power in %
255
100
Control input (DA/D1, DA/D2):
Digital DALI/DSI signal or a push-to-make switch
(switchDIM) can be wired on the same terminals
(DA and DA).
0
70
DSI
150
60
125
50
100
40
75
30
50
20
25
10
PH
switchDIM:
Integrated switchDIM function allows a direct
connection of a push to make switch for dimming
and switching.
SMART-LS II lp: article number 86458258
T
175
80
0
10
100 90 80 70 60 50 40 30 20 15 10 5 4 3 2 1
U
0
20 30 40 50 60 70 80 90 100
relative lighting level in %
Dimming characteristics as seen by the human eye
dimming level in %
lp from the previous generation. Synchronisation
simply has to take place three times within one
minute (3 x 10 s).
To activate the “x” settings again, synchronisation
has to take place four times within one minute.
O
Brief push (< 0.6 s) switches ballast ON and OFF. The
ballasts switch-ON at light level set at switch-OFF.
When the push to make switch is held, PCA ballasts
are dimmed. After repush the PCA is dimmed in the
opposite direction.
The switchDIM fade time is set to 3 s from min. to
max. in the factory settings. With a 20 s push to the
push to make switch this fade time can be changed
to 6 s. In this instance the switchDIM application will
be synchronized to 50 % light level after 10 s and after
20 s the light level rises to 100 % with the new fade
time.
At every synchronizsation (10 s keystroke) the device
will reset to 3 s (factory setting)
In installations with PCAs with different dimming levels
or opposite dimming directions (e.g. after a system
extension), all PCAs can be synchronized to 50 %
dimming level by a 10 s push.
Use of push to make switch with indicator lamp is not
permitted.
AS
E
SMART interface:
An additional interface for the direct connection of
the SMART-LS II lp1) light sensor. The sensor registers
actual ambient light and maintains the individually
defined lux level.
After every mains reset the SMART interface auto­
matically checks for an installed sensor. With the
sensor installed the PCA T5 EXCEL one4all lp x
automatically runs in the constant lux level mode.
ON/OFF switch via mains, switchDIM or DALI/DSI
signal.
DALI/DSI signal = 0 switches off,
DALI/DSI signal ≥ 1 switches on.
With relative DALI dimming commands (e.g. up, down
etc.) or switchDIM signals it is possible to change the
controlled light level temporarily.
Temporarily means that after a switching cycle OFF/
ON command the ballast will start at the preset value
determined by the SMART-LS II lp. The installation of
the two wire bus is according to the appropriate low
voltage regulations.
DALI
200
D
Digital signal DALI/DSI:
The control input is non-polar and protected against
accidental connection with a mains voltage up to
264 V. The control signal is not SELV. Control cable has
to be installed in accordance to the requirements of
low voltage installations.
Different functions depending on each module.
90
225
switchDIM and corridorFUNCTION are very simple tools
for controlling ballasts with conventional momentaryaction switches or motion sensors.
To ensure correct operation a sinusoidal mains voltage
with a frequency of 50 Hz or 60 Hz is required at the
control input.
Special attention must be paid to achieving clear zero
crossings. Serious mains faults may impair the operation of switchDIM and corridorFUNCTION.
2
3
4
N
L
DA
DA
switchDIM PCA T5 EXCEL one4all lp X
2
3
4
DSI
6
7
DA / D1
DA / D2
DSI PCA T5 EXCEL one4all lp X
2
3
4
DALI
Backwards compatibility:
With a simple key combination a PCA T5 EXCEL
one4all lp x can be reset as a normal PCA EXCEL
6
7
6
7
DA
DA
DALI PCA T5 EXCEL one4all lp X
1)
Loading of automatic circuit breakers:
Automatic circuit breaker type
Installation ∅
PCA 1x14/24 T5 EXCEL one4all lp X
PCA 2x14/24 T5 EXCEL one4all lp X
PCA 1x21/39 T5 EXCEL one4all lp X
PCA 2x21/39 T5 EXCEL one4all lp X
PCA 1x28/54 T5 EXCEL one4all lp X
PCA 2x28/54 T5 EXCEL one4all lp X
PCA 1x35/49/80 T5 EXCEL one4all lp X
PCA 2x35/49 T5 EXCEL one4all lp X
PCA 2/80 T5 EXCEL one4all lp
C10
C13
C16
C20
1.5 mm2
1.5 mm2
1.5 mm2
2.5 mm2
5080110135
24344852
34507686
16223236
24344852
16223234
16243238
16223234
10142022
B10
B13
B16
B20
1.5 mm2
1.5 mm2
1.5 mm2
2.5 mm2
25407590
12172426
17253843
8111618
12172426
8111617
8121619
8111617
5 71011
Continuous operation: to calculate the protective saftey switch see main current, page 1
Data sheet 09/11-789-3  We reserve the right to make technical changes without prior notice.
3
Electronic ballasts for dimming to 1 %
Linear lamps T5, 16 mm high efficiency, high output
plug
ADDRESSING
T
Intelligent Temperature Guard
The intelligent temperature guard protects the
PCA T5 EXCEL one4all lp x from thermal overheating by reducing the output power or switching
off in case of operation above the thermal limits of
the luminaire or ballast. Depending on the luminaire
design, the ITG operates at about 5 to 10 °C above Tc
temperature.
plugADDRESSING – simple handling, comissioning
and wiring
The new plug&play solution simplifies handling.
By attaching different colored marked plugs to the
SMART-Interface, group addresses are assigned to
the PCA T5 EXCEL one4all lp x.
This supersedes a single addressing and the devices
can be put into operation without any additional
programming. Another significant advantage of this
concept is in case of exchange and no limits to 64
DALI addresses. Ideal for RGB applications and costeffective system solutions with simple controllers.
Simple – Quick – Plug & Play!
U
corridorFUNCTION
The corridorFUNCTION can be programmed in two
different ways.
To program the corridorFUNCTION by means of software a DALI-USB interface is needed in combination
with a DALI PS. The software can be the configTOOL,
the pcaCONFIGURATOR or the corridorFUNCTION
CONFIGURATOR.
To activate the corridorFUNCTION without using
software a voltage of 230 V simply has to be applied
for five minutes at the switchDIM connection.
The unit will then switch automatically to the
corridorFUNCTION.
Note: If the corridorFUNCTION is wrongly activated
in a switchDIM system (for example a switch is used
instead of pushbutton), there is the option of installing
a pushbutton and deactivating the corridorFUNCTION
mode by five short pushes of the button within three
seconds.
The corridorFUNCTION V2 offers the added benefit of
a second and third preprogrammed profile, which can
be activated by the corridorFUNCTION plugs. It is also
possible to combine the corridorFUNCTION with the
SMART-LS II lp light sensor.
Application and functionallity of profiles see user
manual.
Operating voltage:
lamp
type
1x14
T5
2x14
T5
1x24 / 1x24 T5 / TC-L
2x24 / 2x24 T5 / TC-L
1x21
T5
2x21
T5
1x39 / 1x40 T5 / TC-L
2x39
T5
1x28
T5
2x28
T5
1x54
T5
2x54
T5
1x35
T5
2x35
T5
1x49
T5
2x49
T5
1x80
T5
2x80
T5
Ballast
type
PCA 1x14/24 T5 EXCEL one4all lp X
PCA 2x14/24 T5 EXCEL one4all lp X
PCA 1x14/24 T5 EXCEL one4all lp X
PCA 2x14/24 T5 EXCEL one4all lp X
PCA 1x21/39 T5 EXCEL one4all lp X
PCA 2x21/39 T5 EXCEL one4all lp X
PCA 1x21/39 T5 EXCEL one4all lp X
PCA 2x21/39 T5 EXCEL one4all lp X
PCA 1x28/54 T5 EXCEL one4all lp X
PCA 2x28/54 T5 EXCEL one4all lp X
PCA 1x28/54 T5 EXCEL one4all lp X
PCA 2x28/54 T5 EXCEL one4all lp X
PCA 1x35/49/80 T5 EXCEL one4all lp X
PCA 2x35/49 T5 EXCEL one4all lp X
PCA 1x35/49/80 T5 EXCEL one4all lp X
PCA 2x35/49 T5 EXCEL one4all lp X
PCA 1x35/49/80 T5 EXCEL one4all lp X
PCA 2/80 T5 EXCEL one4all lp
Uout
400 V
400 V
400 V / 400 V
400 V / 400 V
400 V
400 V
400 V / 400 V
400 V
430 V
430 V
430 V
430 V
430 V
430 V
430 V
430 V
430 V
430 V
PH
AS
E
Wattage W
D
O
Intelligent Voltage Guard
Intelligent Voltage Guard is the name of the new
electronic monitor from Tridonic. This inno­vative
feature of the PCA family of control gear from Tridonic
immediately shows if the mains voltage rises above or
falls below certain thresholds. Measures can then be
taken quickly to prevent damage to the control gear.
•If the mains voltage rises above approx. 305 V (voltage depends on the ballast type), the lamp starts
flashing on and off.
•This signal “demands” disconnection of the
power supply to the lighting system.
•The active-current-control of these control gears
is protected against failure caused by the high mains
currents generated as a result of mains undervoltage. The switch off level depends on lamp wattage
and is typically < 140 V.
4
Data sheet 09/11-789-3  We reserve the right to make technical changes without prior notice.
Electronic ballasts for dimming to 1 %
Linear lamps T5, 16 mm high efficiency, high output
Installation instructions:
Wiring type and cross section:
The wiring can be solid cable with a cross section of
0.5 to 0.75 mm² for push terminal and 0.5 mm² for
IDC terminal. For the push-wire connection you have
to strip the insulation (8–9 mm).
wire preparation:
0.5 – 0.75 mm²
Wiring advice:
The lead length is dependent on the capacitance of the cable.
Ballast
Type
PCA 1/xx T5 EXCEL one4all lp X
PCA 2/xx T5 EXCEL one4all lp X
Terminal
ColdHot
11, 12
9, 10
11, 12, 13, 14
9, 10, 15, 16
Maximum capacitance allowed
ColdHot
200 pF
100 pF
200 pF
100 pF
T
With standard solid wire 0.5/0.75 mm² the capacitance of the lead is 30–80 pF/m.
This value is influenced by the way the wiring is made.
Lamp connection should be made with symmetrical wiring.
Hot leads (9, 10, 15, 16) and cold leads (11, 12, 13, 14) should be separated as much as possible.
When using two or more dimmable ballasts in one luminaire with separate dimming controls, the lamp leads
must be kept separate.
U
8 – 9 mm
Dimmable ballasts from Tridonic have to be earthed.
2
3
4
*
2
3
4
12
11
10
9
DA / D1
DA / D2
leads 9, 10: keep wires short, max. 1.0 m
leads 11, 12: max. 2.0 m; ballast must be earthed
* * digital signal (DSI), DALI or switchDIM
*
DA / D2
leads 9, 10, 15, 16: keep wires short, max. 1.0 m
leads 11, 12, 13, 14: max. 2.0 m; ballast must be earthed
PCA T5 EXCEL one4all lp X 2x14–49 W
PCA T5 EXCEL one4all lp 2/80 W
Dimmable ballasts from Tridonic have to be earthed.
PH
RFI:
•Connection to the lamps of the hot leads must
be kept as short as possible
•Mains leads should be kept apart from lamp leads
(ideally 5–10 cm distance)
•Do not run mains leads adjacent to the
electronic ballast
•Twist the lamp leads
•Keep the distance of lamp leads from the
metal work as large as possible
•Mains wiring to be twisted when through wiring
•Keep the mains leads inside the luminaire as short
as possible
General advise:
Electronic ballasts are virtually noise free.
Magnetic fields generated during the ignition cycle
can cause some background noise but only for a
few milliseconds.
PE
L
N
2
3
4
N
L
DALI
PS
6
7
USB
SCI
DA
DA
PE
L
N
2
3
4
6
7
PE
L
N
DA
DA
16
15
14
13
12
11
10
9
* * digital signal (DSI), DALI or switchDIM
AS
E
PCA T5 EXCEL one4all lp X 1x14–80 W
DA / D1
6
7
* * control signal
D
6
7
* * control signal
O
Loosen wire through
twisting and pulling
16
15
14
13
12
11
10
9
16
15
14
13
12
11
10
9
Programming:
With appropriate software and a USB interface
different functions can be activated and various
parameters can be configured in the new
PCA T5 EXCEL one4all lp x. All that is needed
is a DALI-USB and the software.
configTOOL
Full version for programming all the functions
and parameters.
pcaCONFIGURATOR
For programming the corridorFUNCTION, device
configuration (fade time, ePowerOnLevel, etc.)
DC level, compatibility settings, and startup date
and for resetting.
Maximum amount of ballast see DALI/DSI specification.
Isolation and electric strength testing of
luminaires:
Electronic devices can be damaged by high voltage.
This has to be considered during the routine testing of
the luminaires in production.
According to IEC 60598-1 Annex Q (informative only!)
or ENEC 303-Annex A, each luminaire should be submitted to an isolation test with 500 V DC for 1 second.
This test voltage should be connected between the
interconnected phase and neutral terminals and the
earth terminal.
The isolation resistance must be at least 2 MΩ.
As an alternative, IEC 60598-1 Annex Q describes a
test of the electrical strength with 1500 V AC (or 1.414
x 1500 V DC). To avoid damage to the electronic
devices this test must not be conducted.
corridorFUNCTION CONFIGURATOR
For activating and deactivating the corridorFUNCTION
and for project-specific programming of the
PCA T5 EXCEL one4all lp x units.
Maximum amount of ballast see DALI/DSI specification.
 For further technical information please visit www.tridonic.com
max. 64 ECGs (DALI)
PC and the
“configTOOL”
Wiring diagram for programming
PE
2
16
15
14
Data sheet 09/11-789-3  We reserve the34 rightLN to make technical
changes without prior notice.
13
6
7
DA
DA
12
11
10
9
5
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement