Bang & Olufsen BeoVision 8 User`s guide

Bang & Olufsen BeoVision 8 User`s guide
BeoVision 8
Guide
An explanation of symbols in the Guide
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: To reduce the risk of
electric shock, do not remove
cover (or back).
No User-serviceable parts inside.
Refer servicing to qualified
service personnel.
WARNING: To reduce the risk of fire or
electric shock, do not expose this appliance
to rain or moisture. Do not expose this equip­
ment to dripping or splashing and ensure
that no objects filled with liquids, such as
vases, are placed on the equipment.
To completely disconnect this equipment
from the AC Mains, disconnect the mains
plug from the wall socket. The disconnect
device shall remain readily operable.
The lightning flash with arrowhead symbol
within an equilateral triangle, is intended
to alert the user to the presence of un­
insulated “dangerous voltage” within the
product’s enclosure that may be of sufficient
magnitude to constitute a risk of electric
shock to persons.
The exclamation point within an equilateral
triangle is intended to alert the user to the
presence of important operating and main­
tenance (servicing) instructions in the
literature accompanying the product.
Buttons on the Beo4 remote
control
Display on the Beo4 remote
control
Display on the television
TV, LIST
FORMAT
VOL 26
Contents
We expect your Bang & Olufsen
retailer to deliver, install and set up
your products. However, the
information required to install and set
them up is included in the Guide.
This is useful if you move your
products or expand your system at a
later date.
Daily operation, 4
Find out how to use the Beo4 remote control, bring up the menus on the screen,
operate the daily functions of your television and how to adjust sound and picture
format. In addition, find an overview of the on-screen menu system.
Advanced operation, 9
Find out how to operate a connected source, call up a computer image on the
screen and operate your television in Option 4. In addition find out how to operate
an audio system and how to operate your television in a link room.
Installation – Setup, 21
Find out how to handle and place your television and where the sockets are placed.
Find out how to connect a source to your television and how to register extra
equipment. Find out how to set up your television for the first time. This chapter
also contains information about settings for picture and sound.
Maintenance, 33
How to clean your television and change batteries in the Beo4 remote control. This
chapter also contains information about how to customise the Beo4 remote control.
Index, 36
Introducing your television and Beo4
For information about how to operate connected
equipment, refer to the Guide enclosed with it.
For information on how to add extra functions to
those shown in the Beo4 display, refer to the
chapter ‘Customise Beo4’.
The Beo4 remote control gives you access
to all functions. When a function is in use,
you are informed via displays on Beo4
or on the television.
Switch on the television and a connected source
Switch on a connected source
Select channels or teletext pages. Enter data in onscreen menus
TV
0–9
GO
Step up or down through channels or menu items
RADIO
DTV
DVD
CD
V MEM
RECORD
A MEM
7
8
9
4
5
6
1
2
3
STOP
Step back through previous menus
TEXT
0
MENU
EXIT
Exit all on-screen menus
MENU
LIST
GO
LIST
STOP
EXIT
Bring up a menu overlay. Press twie to bring up
the main menu.
Adjust sound volume: press in the middle to mute
the sound
•
Reveal additional functions in the Beo4 display,
such as FORMAT
The Beo4 display shows the source you have
selected, or extra functions available when you
press the LIST button
LIGHT
DTV
Enter information in on-screen menus.
Accept and store instructions or settings. Press
and hold to call up a channel list
TV
FORMAT
TV
Switch the television to standby
Displayed information and menus
Information about the selected source is
shown in the display. On-screen menus allow
you to adjust settings.
TV SETUP
Menu name
CONNECTIONS
SOUND
Menu options
PICTURE
MENU LANGUAGE
Information field
TV
How to use on-screen
menus …
Press to switch on the television
Press twice to bring up the TV
SETUP menu
select
GO
Example of on-screen menu.
TV
MENU
Press to move between the
different menu options
Press to reveal different settings
Press to bring up a menu or store
a setting you have made
GO
Press to step back through
previous menus
STOP
Press to exit all menus
EXIT
Adjust sound and picture format
Several sound adjustment possibilities
are available in your television.
You can adjust the volume or mute
the sound completely at any time.
If channels are broadcasted with
different sound types or languages,
you can choose between the sound
types or languages.
If speakers are connected to your
television, you can adjust the speaker
balance and select a speaker
combination.
While watching TV, you can adjust
the picture format.
Adjust volume or mute the sound
Speaker balance or combination
You can adjust volume or mute the sound at
any time.
If you connect loudspeakers to your tele­vision,
you can change the speaker combination at
any time.
Press either end of the button to
adjust the volume up or down
Press in the middle of the button
to mute the sound
Press either end of the button to
bring the sound back
Prolonged listening at high volume
levels can cause hearing damage!
Press repeatedly to display
SPEAKER on Beo4
LIST
Press to select a speaker
combination
1–3
Press to remove SPEAKER from
the Beo4 display and return to
the source you were using
EXIT
SPEAKER
Speaker combinations
SPEAKER 1 … Sound in the television speakers
only.
SPEAKER 2 … Stereo sound in the two front
speakers.
SPEAKER 3… The television speakers and the
front speakers are active.
Picture format
Select a picture format to optimise the picture.
Press repeatedly to display
FORMAT on Beo4
LIST
Press if you want to optimise the
picture, or …
GO
… press the number of the
desired picture format
FORMAT
1–3
If you have chosen Format 1 …
Press or to select variations
of this format
To temporarily remove the picture from the screen,
press LIST repeatedly to display P.MUTE on Beo4,
then press GO. To restore the picture again, press
any source button, such as TV.
If you have chosen Format 1*
or Format 2 …
Press or to move the
picture up and down
Press to leave the FORMAT
function
Picture formats to choose from …
FORMAT 1 … For standard TV pictures. Three
variations are available: 4:3, 15:9 and Panoramic
view (for the largest picture).
FORMAT 2 … For letter-box pictures. If necessary
move the picture up or down to ensure that
channel names or subtitles – if these appear in
the broadcasted picture – can be seen. In some
cases FORMAT 2 is selected automatically.
FORMAT 3 … For genuine 16:9 wide-screen
pictures. FORMAT 3 is usually selected
automatically. If this is not the case, you can
select it yourself.
EXIT
*Pictures in 4:3 format cannot be
moved up and down.
NOTE! For further information about how to
connect speakers to the television, refer to the
chapter ‘Socket panel’ on page 25.
Menu overview
The illustration on this page shows
the content of the menu system , and
also indicates where in the Guide you
can find further information about
the menus.
T V SETUP pp. 30
TV
CONNEC TIONS
PIC TURE
pp. 34
BRIGHTNESS
pp. 31
AV 1
CONTRAST
COLOUR
TINT
SOURCE
HORIZONTAL SIZE
IR SOCKET
HORIZONTAL POSITION
HDMI
VERTICAL POSITION
AV 2
SOURCE
MENU L ANGUAGE IR SOCKET
DANSK
HDMI
DEUTSCH
YPbPr
ENGLISH
AV 3
ESPANOL
SOURCE
FRANCAIS
IR SOCKET
ITALIANO
HDMI
NEDERLANDS
VGA
SVENSKA
p. 32
AV 4
SOURCE
IR SOCKET
HDMI
SOUND pp. 34
VOLUME
CENTRE
BALANCE
BASS
TREBLE
LOUDNESS
POSITION
The extended on-screen menu system for the
television. The greyed menu items indicate
optional extras which may or may not be present
in your system.
Press MENU on Beo4 to access the main menu. To
step directly to a menu entry without pressing GO,
use the number buttons on Beo4.
Advanced operation
This chapter tells you how to operate
a connected source, how to use your
television as a computer monitor, and
how to operate your television in
Option 4.
Daily use, 4
Find out how to use the Beo4 remote control, bring up the menus on the screen,
operate the daily functions of your television and how to adjust sound and picture
format. In addition, find an overview of the on-screen menu system.
Advanced operation, 9
•
•
•
•
•
Use connected video equipment with Beo4, 10
Use your television as a computer monitor, 13
Two televisions in the same room, 14
Connect and operate an audio system, 16
BeoVision in a link room, 18
Installation – Setup, 21
Find out how to handle and place your television and where the sockets are placed.
Find out how to connect a source to your television and how to register extra
equipment. Find out how to set up your television for the first time. This chapter
also contains information about settings for picture and sound.
Maintenance, 33
How to clean your television and change batteries in the Beo4 remote control. This
chapter also contains information about how to customise the Beo4 remote control.
Index, 36
Use connected video equipment with Beo4
10
The built-in Peripheral Unit Controller
acts as an interpreter between
connected video equipment, such as
a set-top box, video recorder or DVD
player, and the Beo4 remote control.
You can use the Beo4 remote control
to gain access to the channels and
functions offered by your equipment.
Some functions are available via Beo4
when you switch on the equipment.
Additional functions are available
through a Peripheral Unit Controller
menu that you bring up on the
screen.
For instruction in the various
functions offered by your equipment,
please refer to the product’s own
user’s guide.
For further information about
supported equipment, contact your
Bang & Olufsen retailer.
Peripheral Unit Controller menu
Buttons on the remote controls included with
your equipment may not match those on
Beo4. To see which Beo4 buttons activate
specific services or functions, bring up the
Peripheral Unit Controller menu on the
screen.
Press a source button to switch
on connected equipment
TV
DTV
Press to bring up the Peripheral
Unit Controller menu
MENU
Press the number button that
activates the function you want,
or …
1–9
… press one of the coloured
buttons to activate a function
When you have selected a settop box as a source, press MENU
twice to bring up the television’s
main menu.
1
GUIDE
2
MENU
3
TEXT
4
INFO
5
WIDE
1
GUIDE
2
MENU
3
TEXT
4
INFO
5
WIDE
Example of a Peripheral Unit Controller menu – The
Beo4 buttons are shown to the left on the menu,
and the functions they control are shown to the
right. The menu may also list buttons on the remote
control included with your connected equipment.
11
Universal Beo4 operation
Use equipment menus
Use equipment in a link room
If you know which Beo4 button activates the
function you want, you can activate the
function without bringing up the Peripheral
Unit Controller menu first.
Once you have activated connected
equipment, you can operate its own menus
with Beo4.
When you have connected equipment to the
television in the main room, you can operate
it and listen to the sound via the link room
television.
While your equipment is on …
Press GO and then the number
GO
button that activates the
1–9
function you want
While equipment menus are
shown …
Moves the cursor up or down
Moves the cursor left or right
Press one of the coloured
buttons to activate a function
Press GO and then or to
step up or down through
channels directly
GO
Press and hold GO to bring
up the Program guide or the
‘Now/Next’ banner on the screen
depending on your source
GO
Selects and activates a function
GO
GO
Press GO and then or to
step between menu pages or
step in channel lists
GO
Exits menus, or returns to
a previous menu*
STOP
Exits menus, enters or exits
different modes, such as radio
EXIT
Use the coloured buttons as
indicated in the menus of your
connected equipment
*Depending on your source, you
may have to press EXIT twice
instead of STOP to return to a
previous menu.
Press to switch on equipment in
the main room
V MEM
DVD
DTV
Press GO and then the number
button that activates the
function you want
GO
1–9
Press one of the coloured
buttons to activate a function
12
>> Use connected video equipment with Beo4
Playback on a video recorder or DVD player
You can switch on your equipment, start and
stop playback and search back and forth
using Beo4. Eject a video cassette or DVD via
the close-up operation panel on the
equipment.
Press to switch on your video
recorder or DVD player and start
playback
V MEM
DVD
Search back and forth
Press to pause playback
STOP
Press to resume playback, or …
GO
… press to stop playback
completely
STOP
Switch the system to standby
•
If your equipment has an
automatic standby feature that
switches it off when playback
has been paused or stopped for
a period of time, you can
reactivate the equipment by
pressing another source button
on Beo4, such as TV, followed
by V MEM or DVD.
Use your television as a computer monitor
If you connect your television to a
computer, as described on page 26,
you can use it as a monitor.
IMPORTANT! If you wish to connect a
computer to the television and use the
tele­vision as a monitor, make sure that you
disconnect the television, the computer,
and all equipment connected to the
computer from the mains before you
connect the computer and the television
to each other.
When in use, the computer must be
connected to a grounded wall outlet as
specified in the computer’s setting-up
instructions.
Bring up the computer image on the screen
To see the computer picture on the television
screen, you must bring it up with Beo4.
To bring up the computer
picture …
Press repeatedly until PC*
appears in the Beo4 display
Press to bring up the picture
You can then operate the
computer as you normally would.
*In order to display PC on Beo4,
you must first add it to the Beo4
list of functions. For further
information, refer to the chapter
‘Customise Beo4’ on page 36.
LIST
PC
GO
The television supports the following screen
resolutions: 60 Hz; 480p, 576p, 600p, 720p, 768p.
13
Two televisions in the same room
14
If you have placed your BeoVision 8
in a room where you already have a
Bang & Olufsen television, and
commands from Beo4 can be
received by both televisions, you
must change the option setting of
BeoVision 8. This prevents simultaneous
activation of both televisions.
One remote control for both televisions
For your television to function properly, it is
essential that the television is set to the
correct Option:
To set your television for Option 4 …
>While holding the • button on Beo4, press LIST.
>Let go of both buttons.
>Press LIST repeatedly to display OPTION? on
Beo4 and press GO.
>Press LIST repeatedly to display V.OPT on Beo4
and press 4.
Operate your television in Option 4 …
Normally, you can activate a source, such as TV,
simply by pressing the relevant source button on
Beo4. However, when you set your television to
Option 4, you must do the following:
>Press LIST repeatedly until LINK* is shown in
the Beo4 display.
>Press a source button, such as TV.
*In order to display LINK on Beo4, you must add it to
the Beo4 list of functions. For further information,
refer to the chapter ‘Customise Beo4’ on page 36.
BeoVision 8
Option 4
LIST
LINK
TV
TV
In order to use teletext on a television you have set
to Option 4, you must set up Beo4 to ‘VIDEO 3’,
but this limits the Beo4 functions that can be used
with televisions set to other Options. For further
information refer to the chapter ‘Customise Beo4’
on page 36.
15
Connect and operate an audio system
16
If you connect a compatible audio
system to your television, you obtain
the benefits of an integrated audio/
video system.
Connect your audio system
Play a CD on your audio system using
the television speakers, or switch on
a TV programme and send the sound
to your audio system speakers.
Option setting
If your television has been set up in an AV
system, you may need to set it to the correct
option. Switch the entire system to standby.
Your AV system can be placed
together in one room or in two
rooms with the television placed in
one room, and the audio system with
a set of speakers placed in another.
Not all Bang & Olufsen audio systems
support integration with the
television.
Using a Master Link cable, connect the
MASTER LINK sockets on the television and
the audio system.
Option setting for the television
>While holding the • button on Beo4,
press LIST.
>Let go of both buttons.
>Press LIST repeatedly to display OPTION? on
Beo4 and press GO.
>Press LIST repeatedly to display V.OPT on Beo4
and then key in the appropriate number (1 or 2).
Option setting for the audio system
>Repeat the procedure as described above.
>Press LIST repeatedly to display A.OPT on Beo4
and then key in the appropriate number (0, 1, 2,
5 or 6).
Option 2
Option 0
In one room – all speakers are connected to the
television.
Option 1
Option 1
The television and audio system in the same room.
Option 2
Option 2
Audio system in one room, and the tele­vision in
another.
17
Use an integrated audio/video system
If you integrate your audio system and your
television, you can choose a speaker
combination appropriate to the current video
or audio programme, and also record video
sound on the audio system.
Video sound recording
If you listen to sound from your television on
your Bang & Olufsen audio system’s speakers,
and your audio system has a tape recorder,
you can record television sound on the audio
tape recorder. Refer to the Guide enclosed
with your audio system for further
information.
LIST
LIST
AV
AV
TV
CD
To listen to sound from a television source on your
audio system speakers without switching on the
screen, press LIST repeatedly to display AV* on
Beo4, and then press a source button, such as TV.
TV
LIST
AV
TV
To listen to sound from television on your audio
system speakers with the screen switched on,
press TV, press LIST repeatedly to display AV*, and
then press TV again..
*NOTE! In order to display AV on Beo4, you must
first add it to the Beo4 list of functions. For further
information, refer to the main tele­vision User’s
guide and the chapter ‘Customise Beo4’.
To listen to audio sound on the television speakers,
press LIST repeatedly to display AV* on Beo4, and
then press an audio source button, such as CD.
BeoVision in a link room
18
If you choose to use your television in
a link room, you can operate all
connected systems through the
television.
Option setting
Main Room
Link Room
For your entire system to function
properly, it is essential that the link
room television is set to the correct
Option before you connect it to the
system in the main room.
Option 6*
RF OUT
You must follow the procedure described
below when you connect your television
for use in a link room:
1 Connect the link room television to the
mains supply.
2 Using the Beo4 remote control,
program the link room television to
Option 6.
3 Disconnect the link room television
from the mains supply.
4 Make the link connections.
5 Reconnect the link room television to
the mains supply.
MASTER
LINK
AV2
Link Tuner
To set the link room television to the correct
Option …
>While holding the • button, press LIST.
>Let go of both buttons.
>Press LIST repeatedly to display OPTION? on
Beo4 and press GO.
>Press LIST repeatedly to display V.OPT on Beo4
and press 6.
Timer Play in link room*
If your television is placed in the link room, it can
be part of a Timer Play programmed on your main
room system.
To make your television part of a
Timer Play …
>Press TV to switch on the television.
>Press MENU to bring up the TV SETUP menu
and press to highlight PLAY TIMER.
>Press GO to bring up the PLAY TIMER menu.
TIMER ON/OFF is already high­lighted.
>Press or to reveal ON.
>Press GO to store the setting.
*NOTE! If your BeoVision 8 is linked to a video or
audio master with the possibility of programming
a Timer Play, the Timer Play can be executed on
BeoVision 8.
MASTER
LINK
If you connect the television for use in a link room
where other link systems are already connected,
you must set the television to Option 5 instead. If
you wish to ditribute both sound and pictures
from a main room video source to your link room
television, an external tuner will be necessary.
19
Link room operation
When you are in the link room, you can
operate all connected systems with the Beo4
remote control.
Use sources present only in one of the
rooms …
>Press the button for the source you wish to use;
operate the selected source as usual.
Use a main room source – present in both
rooms …
>Press LIST repeatedly on Beo4 until LINK* is
shown in the display.
>Press the button for the source you wish to use;
operate the source as usual.
If you only wish to switch on audio mode from a
main room video source, press LIST repeatedly
until AV.V is shown in the display instead of LINK,
then press the button for the source you wish to
use and operate the source as usual.
Use a link room source – present in both
rooms …
>Press the button for the source you wish to use;
operate the source as usual.
Listen to stereo sound in your link room …
Usually sound distributed from a main room video
source, such as a set-top-box, to the link room is
transmitted in mono. However, you can select
stereo sound:
>Press DTV to switch on the television.
>Press LIST repeatedly until AV* is shown in the
Beo4 display..
>Press DTV to activate a source connected to the
main room system, such as a set-top box.
While using this function, distribution of other
main room sources to other link room systems is
not possible. You can only listen to stereo sound if
your television is set for Option 6.
Main Room
Link Room
*In order to display LINK, AV and AV.V on Beo4,
you must first add them to the Beo4 list of
functions. For further information, refer to the
chapter ‘Customise Beo4’.
20
Installation – Setup
In this chapter, you can find out how
to place and connect your television.
It also gives you an overview of the
socket panels.
We recommend that you follow the
procedure described below when
you set up your television:
– Unpack the television
– Consider the appropriate
surroundings for your television
– Mount the television on the
chosen stand or bracket
– Place the television
– Connect the cables, additional
equipment, and speakers
This procedure is described in detail
on the following pages.
In this chapter, you can also find out
how to perform the first-time setup
procedure and adjust available
settings, such as picture and sound.
Daily use, 4
Find out how to use the Beo4 remote control, bring up the menus on the screen,
operate the daily functions of your television and how to adjust sound and picture
format. In addition, find an overview of the on-screen menu system.
Advanced operation, 9
Find out how to operate a connected source, call up a computer image on the
screen and operate your television in Option 4. In addition find out how to operate
an audio system and how to operate your television in a link room.
Installation – Setup, 21
•
•
•
•
•
•
•
•
Set up your television, 22
Camera and headphones sockets, 24
Socket panel, 25
Connect additional equipment, 26
First-time setup of your television, 27
Register additional video equipment, 28
Adjust picture and sound settings, 30
Choose menu language, 32
Maintenance, 33
How to clean your television and change batteries in the Beo4 remote control. This
chapter also contains information about how to customise the Beo4 remote
control.
Index, 36
21
Set up your television
22
For information about how to fasten
and run the cables on the rear of the
television, refer to this page.
For further information about the
socket panel, refer to page 25.
Handling your television
Avoid placing your television in direct sun­light
or direct artificial light, such as a spotlight, as
this may reduce the sensitivity of the remote
control receiver. Also if the screen is over­heated,
black spots may appear in the picture. These
spots disappear again, once the tele­vision
cools down to normal temperature.
To avoid injury, use Bang & Olufsen approved
stands or wall brackets only.
Make sure that the television is set up, placed
and connected in accordance with these
instructions.
The television is developed for indoor use in
dry, domestic environments only. Use within
a temperature range of 10–40°C (50–105°F).
To remove the cover for the connection panel, first
pull out, then pull down at the bottom, also if the
television is placed on a video stand.
Do not place any items on top of the tele­vision.
Always place your television on a firm and
stable surface.
Do not attempt to open the television. Leave
such operations to qualified service personnel.
Your television was designed to be left in
standby mode when not in use. Therefore, to
facilitate remote control operation, it is
essential that you do not disconnect it from
the mains. The television can only be switched
off completely, if you disconnect it from the
mains.
A
B
IMPORTANT! For safety reasons the mains supply
cable must be fastened to the cable strip (A). All
cables must be run through the cable strip (B).
However, if your setup includes a VGA connection,
do not run the VGA cable through the cable strip
(B). Instead, use the two screws in the VGA plug
to fasten it to the socket.
23
Connection of the television
Before you connect the television to the mains,
you must connect it to an external tuner. Make
sure you have a 21-pin cable, an adaptor and
other required cables, then connect the
equipment as illustrated to the right.
BeoVision
AV1
AV1 (R-L-CVBS)
To be able to use the remote control included with
your external tuner, do not cover its IR receiver
entirely.
Mains connections
Connect the television to the wall outlet. Use
the ~ socket on the connection panel.
If you are going to connect speakers or any other
equipment to the television, do not connect it to
the mains yet!
If you damage the supplied mains cord, it may
affect the TV picture adversely!
12 V
DC
C1 / C2
External source box
Video Sense box
R
L
CVBS IN
Automatic standby …
When you register a source in the
CONNECTIONS menu, you can also select an
‘AUTO STANDBY’ time for your source. This
means that you can select if the connected
source should switch to standby auto­matically.
The options are:
AFTER 0 MIN … The source switches to stand­by
immediately when you select another source.
AFTER 30 MIN … The source switches to stand­by
30 minutes after you have selected another
source*.
AT TV STANDBY … The source switches to stand­
by when you switch the television to stand­by.
NEVER … The source does not switch to stand­by
automatically.
FOLLOW TV … The source switches on, when you
switch your television on and it switches to
stand­by, when you switch your television to
stand­by.
Sources must be set up in accordance with the
documentation enclosed with them.
*If you switch the television to standby before the
30 minutes have passed, the source is also
switched to stand­by.
Camera and headphones sockets
24
You can connect headphones and
listen to a programme, or you can
connect a Camcorder and watch your
home movies on the television. If you
have connected a video tape
recorder, you can copy Camcorder
recordings onto a videotape.
Sockets for temporary connections
PHONES
You can connect stereo headphones to the socket
marked PHONES. Adjusting volume will affect
both the television speakers and the headphones.
Muting sound will affect television speakers only.
PHONES
R
L
These sockets are for the connection of
a Camcorder:
R–L
For audio connection (right and left sound channel
respectively).
VIDEO
For the video signal.
Watch digital pictures on your television
To watch your camera pictures, connect the camera
and switch the television on. The tele­vision auto­
matically registers the signal and you can see the
still pictures on the screen.
If the signal from the camera is switched off …
>Press LIST repeatedly to display CAMERA* on
Beo4 and press GO.
*In order to display CAMERA on Beo4, you must
first add it to the Beo4 list of functions. For further
information, refer to the chapter ‘Customise Beo4’
on page 36.
VIDEO
Watch and copy from a Camcorder
If you have connected a video tape recorder to
your television, and you connect your Camcorder,
you can copy Camcorder recordings onto a
videotape.
To copy a recording from a Camcorder …
>Connect your Camcorder and start playback on
the Camcorder. The television automatically
registers the signal and you can see the pictures
on the television screen.
>Press RECORD twice to start recording.
Choosing another source or switching off the tele­
vision during recording from a Camcorder disrupts
recording. It is not possible to view TV channels
during recording.
Socket panel
The socket panel on your television
allow you to connect signal input
cables as well as a variety of extra
equipment, such as a video recorder
or DVD.
The AV sockets are the primary
sockets for connection of extra
equipment. Any equipment you
connect to these sockets must be
registered in the CONNECTIONS
menu. For further information, refer
to the chapter ’First-time setup of
your television’ on page 30.
AV 1
25
AV 2
AV 2
POWER LINK AV3
VGA
AV 3
~
Connections to the mains.
AV 1*
21-pin socket for the AV connection of a primary
external tuner, such as a set-top box or a DVD
recorder.
AV 2 / Y – Pb – Pr
21-pin socket for the connection of additional
equipment, such as a DVD, a set-top box or a
recorder, or for connection of a link tuner.
AV3
R – L: Right and left line signal (audio).
VIDEO: Video signal.
AV3 – VGA
VGA connection for receiving analogue graphics
from an external PC. Supports the following
screen resolutions: 60 Hz; 480p, 576p, 600p,
720p, 768p.
AV 4
21-pin socket for the AV connection of other
equip­ment.
*Note! To connect equipment to the AV1, AV2 and
AV4 sockets, an adaptor will be necessary.
C1
HDMI
AV 4
MASTER LINK
RF
OUT
C2
POWER LINK
For connection of external Bang & Olufsen loud­
speakers. Connect a Power Link splitter if your
connected loudspeakers have only one Power Link
socket.
C1 – C2
For IR control signals to external equipment
connected to the AV sockets.
HDMI
(High Definition Multimedia Interface) to be used
in conjunction with an AV socket. For connection
of an HDMI video source or a PC.
MASTER LINK
Socket for connection of a compatible Bang &
Olufsen music system. The socket is also used for
BeoLink distribution of sound throughout the
house.
MODULATOR
Not for use in this setup.
Connect additional equipment
26
You can connect a computer and use
your television as a monitor.
Make sure that all connected equipment
is registered in the CONNECTIONS
menu. For further information, refer
to the chapter ‘Register additional
video equipment’ on page 28.
Connect a computer
BeoVision
R
L
Disconnect the television, the computer, and
all equipment connected to the computer
from the mains.
Using the appropriate type of cable, connect
one end to the VGA output socket on your
computer, and the other end to the VGA
socket on the television.
To hear sound from the computer in the tele­
vision speakers, use the appropriate cable and
connect the sound output on the computer
to the R – L sockets on the tele­vision.
Reconnect the tele­vision, the computer, and
all equipment connected to the computer to
the mains.
AV3 VGA
IMPORTANT! If you wish to connect a computer to
the television and use the television as a monitor,
make sure that the television, the computer, and
all equipment connected to the computer are all
disconnected from the mains before you connect
the computer and the television to each other.
In addition, the computer must be connected to a
grounded wall outlet as specified in the computer’s
setting-up instructions.
First-time setup of your television
The setup procedure described here is
activated only when the television is
connected to the mains and switched
on for the first time.
You must select the menu language
and register any extra equipment you
have connected.
Select menu language
27
Register extra equipment
MENU LANGUAGE
CONNECTIONS
DANSK
AV1
V. MEM
DEUTSCH
AV 2
DTV
ENGLISH
AV3
PC
ESPANOL
FRANCAIS
ITALIANO
NEDERLANDS
SVENSKA
select
accept
GO
The first time you switch on your television,
you must select which language you want all
the menus to be displayed in.
The menu language setup appears. If you wish to
change the menu language at a later date, you can
find the item MENU LANGUAGE in the TV SETUP
menu.
>Press TV to switch on the television.
The language menu appears.
>Press or to move between the displayed
languages, if necessary.
>Press GO to store your choice.
store
select
GO
You have to register the extra equipment
connected to your television.
When the CONNECTIONS menu appears …
>Press or to step between the different
socket groups: AV1, AV2, AV3 and AV4.
>Press GO to be able to register a connected
product to the highlighted socket group.
>Press or to move between the sockets in
the group.
>Press or to register what you have
connected to the highlighted socket.
>Press GO to be able to select another socket
group.
>When you have completed your settings, press
the green button to store the setup.
Register additional video equipment
28
If you connect additional video
equipment to your television, you
must register the equipment in the
CONNECTIONS menu.
When the system is first set up, the
CONNECTIONS menu appears
automatically on the screen, so you
can register any equipment you may
have connected to your televison. If
you connect equipment at a later
date, on a permanent basis, then you
must register this equipment in the
CONNECTIONS menu.
For information about where and
how to connect extra equipment,
refer to the previous pages and the
chapter ‘Socket panel’ on page 25.
What is connected?
Registering the equipment connected to the
television enables you to activate it with the
Beo4 remote control.
>Press TV to switch on the television.
>Press MENU to bring up the TV SETUP menu.
>Press to highlight CONNECTIONS.
>Press GO to call up the CONNECTIONS menu.
>Press or to step between the different
sockets: AV1, AV2, AV3 and AV4.
>Press GO to be able to register a connected
product to the highlighted socket.
>Press or to move between the different
settings.
>Press or to register what you have
connected to the highlighted socket.
>Press GO to store the settings and be able to
select another AV socket.
>When you have completed your settings, press
STOP to back up through previous menus or
press EXIT to exit all menus directly.
AV1
SOURCE
V. MEM
IR SOCKET
NONE
HDMI
NO
select
GO
29
When you have connected additional video
equipment to your television, you must also
‘tell’ the system what is connected.
What’s on the CONNECTIONS menu …
AV 1
TV … if you have connected a source registered
as TV.
DTV … if you have connected a source
registered as DTV.
DVD … If you have connected a DVD player.
DVD … If you have connected a Bang & Olufsen
DVD player.
V.MEM … If you have connected a recorder.
V.AUX … If you have connected a source
registered as V.AUX.
NONE … if no equipment is connected.
IR SOCKET … If the equipment connected to this
socket is controlled via IR, select which socket
the IR controller is connected to; C1 or C2.
HDMI … If the source connected to this AV socket
is also connected to the HDMI socket, select
YES, otherwise select NO.
AV 2
TV … if you have connected a source registered
as TV.
DTV … if you have connected a source
registered as DTV.
DVD … If you have connected a DVD player.
DVD … If you have connected a Bang & Olufsen
DVD player.
V.MEM … If you have connected a recorder.
V.AUX … If you have connected a source
registered as V.AUX.
LINK … To display sound and pictures from a
main room video source, if your television is
placed in a link room.
NONE … if no equipment is connected.
IR SOCKET … If the equipment connected to this
socket is controlled via IR, select which socket
the IR controller is connected to; C1 or C2.
HDMI … If the source connected to this AV socket
is also connected to the HDMI socket, select
YES, otherwise select NO.
YPbPr … Indicates whether or not the equipment
is connected to the television via the YPbPr
sockets. Options are YES and NO
AV 3
TV … if you have connected a source registered
as TV.
DTV … if you have connected a source
registered as DTV.
DVD … If you have connected a DVD player.
PC … If you have connected a BeoMedia.
PC … If you have connected a PC
V.AUX … If you have connected a source
registered as V.AUX.
NONE … if no equipment is connected.
IR SOCKET … If the equipment connected to this
socket is controlled via IR, select which socket
the IR controller is connected to; C1 or C2.
HDMI … If the source connected to this AV socket
is also connected to the HDMI socket, select
YES, otherwise select NO.
VGA … Indicates whether or not the equipment –
High Definition video source or PC – is
connected to the television via the VGA socket.
Options are YES and NO.
AV 4
TV … if you have connected a source registered
as TV.
DTV … if you have connected a source
registered as DTV.
DVD … If you have connected a DVD player.
DVD … If you have connected a Bang & Olufsen
DVD player.
V.MEM … If you have connected a recorder.
V.AUX … If you have connected a source
registered as V.AUX.
NONE … if no equipment is connected.
IR SOCKET … If the equipment connected to this
socket is controlled via IR, select which socket
the IR controller is connected to; C1 or C2.
HDMI … If the source connected to this AV socket
is also connected to the HDMI socket, select
YES, otherwise select NO.
DTV SETUP
SELECTOR
NOKIA 9800S/025
NOKIA 9602S
NOKIA 9820t
NOKIA 9200
PACE DTR730-IM
select
GO
If you have connected a set-top box, you will be
prompted to select your set-top box from an onscreen list when you select STB in the
CONNECTIONS menu.
Adjust picture and sound settings
30
Picture and sound settings are preset
from the factory to neutral values
which suit most viewing and listening
situations. However, if you wish, you
can adjust these settings to your liking.
Adjust picture brightness, colour or
contrast. Sound settings include volume,
bass and treble.
Store your picture and sound settings
temporarily – until your television is
switched off – or store them
permanently.
For information about how to change
the picture format, refer to the Guide
page 7.
Change brightness, colour or contrast
Adjust the picture settings via the PICTURE
menu. Temporary settings are cancelled
when you switch off the television.
>Press TV to switch on the television.
>Press MENU to bring up the TV SETUP menu
and press to highlight PICTURE.
>Press GO to bring up the PICTURE menu.
>Press or to move through menu items.
>Press or to adjust the values.
>Press EXIT to store your settings until you
switch off the television, or …
>… press GO to store your settings permanently.
To temporarily remove the picture from the screen,
press LIST repeatedly to display P.MUTE on Beo4,
then press GO. To restore the picture again, press
any source button, such as TV.
PICTURE
BRIGHTNESS
...............
CONTRAST
...............
COLOUR
...............
TINT
...............
HOR. SIZE
...............
HOR. POSITION
...............
VERT. POSITION
...............
store
GO
What’s on the PICTURE menu …
BRIGHTNESS … Adjusts the picture brightness.
CONTRAST … Adjusts the contrast level in the
picture.
COLOUR … Adjusts the colour intensity in the
picture.
TINT … Adjusts the colour shade or nuance on the
current channel. Only available for video sources
using the NTSC signal.
If a source, such as PC, is connected via the VGA
socket, the following options appear ...
HOR. SIZE … Adjusts the width of the picture.
HOR. POSITION … Adjusts the position of the
picture horizontally.
VERT. POSITION … Adjusts the position of the
picture vertically.
31
Change volume, bass or treble
Adjust the sound settings via the
SOUND SETUP menu. Temporary settings are
cancelled when you switch off the television.
>Press TV to switch on the television.
>Press MENU to bring up the TV SETUP menu
and press to highlight SOUND.
>Press GO to bring up the SOUND menu.
>Press or to move through menu items.
>Press or to adjust the values or choose a
setting.
>Press EXIT to store your settings until you switch
off the television, or …
>… press GO to store your settings permanently.
What’s on the SOUND SETUP/SOUND
ADJUSTMENT menu …
VOLUME … Adjusts the volume level the TV uses
when you switch it on.
(CENTRE) … Only available if you have connected
external loudspeakers to the television. Adjusts
the balance between the external and internal
speakers.
BALANCE … Adjusts the balance between the
speakers.
BASS … Adjusts the bass level.
TREBLE … Adjusts the treble level.
LOUDNESS … The loudness feature compensates
for the human ear’s lack of sensitivity to high
and low frequencies. These frequencies are
boosted at low volume levels so that low music
becomes more dynamic. Loudness can be set to
ON or OFF.
POSITION … When the television is placed in a
corner or close to a wall, the bass level is
boosted compared to the bass level achieved
when placed in a more free-standing position.
To remove this excessive bass boost, select the
correct POSITION setting. If the television is
placed in a corner or up against a wall, select
POSITION 2. If the television is placed away
from a wall, select POSITION 1.
SOUND
VOLUME
...............
CENTRE
...............
BALANCE
..............
BASS
...............
TREBLE
...............
LOUDNESS
OFF
POSITION
1
store
GO
Choose menu language
32
The menu language you choose
during the first-time setup of your
television can be changed at any
time.
Once a menu language is chosen, all
menus and display messages are
shown in this language.
You can select the language for on-screen
menus via the TV SETUP menu. The text on
the screen changes as you move from
language to language.
MENU LANGUAGE
DANSK
DEUTSCH
ENGLISH
ESPANOL
>Press TV to switch on the television.
>Press MENU to bring up the TV SETUP menu
and press to highlight MENU LANGUAGE.
>Press GO to bring up the MENU LANGUAGE
menu.
>Use and to move to your language choice.
>Press GO to make your choice.
>Press STOP to back up through previous menus
or press EXIT to exit all menus directly.
FRANCAIS
ITALIANO
NEDERLANDS
SVENSKA
select
accept
GO
Maintenance
Regular maintenance, such as cleaning
the television, is the responsibility of
the user. To achieve the best result,
follow the instructions to the right.
Contact your Bang & Olufsen retailer
to determine recommendations for
regular maintenance.
33
Cleaning
Never use alcohol or other solvents to clean any
part of the television, stand or wall bracket!
Cabinet surfaces
Wipe dust off the surfaces using a dry, soft cloth.
Remove grease stains or persistent dirt with a soft,
lint-free, firmly wrung cloth, dipped in a solution of
water containing only a few drops of mild detergent,
such as washing-up liquid.
Picture screen
To clean the picture screen, use a mild window
cleaning fluid (not containing alcohol). To retain
the optimum performance of the screen, make sure
that no streaks or traces of the cleaning fluid are
left on the screen.
Beo4
Wipe the Beo4 remote control with a soft, lint-free,
firmly wrung cloth.
The speaker cover may also be cleaned with a soft
brush mounted on a vacuum cleaner, set to the
lowest level.
Changing the Beo4 batteries
When BATTERY appears in the Beo4 display, it is
time to change the batteries in the remote control.
2
1
The Beo4 requires three batteries. We recommend
that you use Alkaline batteries only (1.5 V – size
AAA). Replace the batteries as shown on this
page. Keep a finger on top of the batteries until
the lid is replaced
When you have replaced the batteries, wait about
10 seconds until TV appears in the display. The
Beo4 remote control is then ready for use.
Do not expose batteries to excessive heat such as
sunshine, fire or the like!
3
2
1
Customise Beo4
34
The Beo4 buttons give direct remote
control of a large number of television
functions, and the Beo4 display gives
you access to even more functions.
Whenever a source is displayed on
Beo4 (TV, RADIO, etc.), you can press
the LIST button and bring up extra
functions in the display to help you
operate that source, just as if you
were calling up extra buttons. You
can also switch on extra equipment
connected to your television.
You can customise a new Beo4 to suit
your television, and change the order
in which these extra functions appear
when you call them up.
Note that Beo4 contains a list of all of
Bang & Olufsen’s extra audio and video
functions, but only those functions
supported by the television work when
you call them up in the Beo4 display.
Set up Beo4
Add an extra ‘button’
The Beo4 is set up for use with BeoVision 8
from the factory. However, if you buy a new
Beo4 you can set this up for your television also.
When you add a new function to the Beo4
list, you can then bring up this new ‘button’
in the Beo4 display.
Press and hold the standby
button down
•
Press and hold the standby
button down
•
Press to get access to the Beo4
setup function
LIST
Press to get access to the Beo4
setup function
LIST
Let go of both buttons. ADD?
appears in the display
ADD?
Press repeatedly to display
CONFIG? on Beo4
LIST
Press to be able to select the
type of configuration
GO
Press repeatedly to display
VIDEO? on Beo4
LIST
Press to get access to the video
configuration
GO
Press repeatedly to display
VIDEO 2 on Beo4*
LIST
Press to store the configuration
GO
STORED appears, indicating that
the configuration has been
stored. You leave the Beo4
setup function auto­matically
*If you have set your television to
Option 4, select ‘VIDEO 3’.
CONFIG?
VIDEO?
Let go of both buttons. ADD?
appears in the display
Press to bring up the list of
available ‘buttons’ to add from.
The first ‘button’ appears in the
display, it flashes on and off
ADD?
GO
Press to move forwards or
backwards in the list of all extra
‘buttons’
Press to add and place the
‘button’ on its preset position or
as the first ‘button’ in the list,
or …
GO
… press to insert the ‘button’ at
a specific position in the list
1–9
VIDEO 2
STORED
ADDED appears, indicating that
the ‘button’ has been added.
You leave the Beo4 setup
function automatically
ADDED
35
Move extra ‘buttons’
Remove an extra ‘button’
You can rearrange the order in which the
extra ‘buttons’ appear when you press LIST.
You can remove any of the extra ‘buttons’
that are available when you press LIST.
Press and hold the standby
button down
•
Press and hold the standby
button down
•
Press to get access to the Beo4
setup function
LIST
Press to get access to the Beo4
setup function
LIST
GO
Let go of both buttons. ADD?
appears in the display
ADD?
Press repeatedly to display
MOVE? on Beo4
LIST
Press to bring up the list of extra
‘buttons’. The first ‘button’
appears in the display
GO
MOVE?
Press to move forwards or
backwards in the list of extra
’buttons’
Press to move and place the
displayed ‘button’ as the first in
the list, or …
… press to move the ‘button’ to
a specific position in the list
MOVED appears, indicating that
the ‘button’ has been moved.
You leave the Beo4 setup
function automatically
Let go of both buttons. ADD?
appears in the display
ADD?
Press repeatedly to display
REMOVE? on Beo4
LIST
Press to bring up the list of extra
‘buttons’. The first ‘button’
appears in the display
GO
REMOVE?
Add an extra ‘button’ to Beo4, either to the top of
the list or to a specific position.
Press to move forwards or
backwards in the list of extra
’buttons’
GO
1–9
Press to remove the ‘button’
shown in the display
REMOVED appears, indicating
that the ‘button’ has been
removed. You leave the Beo4
setup function automatically
3
GO
REMOVED
GO
3
MOVED
Move extra ‘buttons’, either to the top of the list
or to a specific position.
36
Index
Beo4 remote control
Contact
Add a ‘button’ to the Beo4 list, 34
Changing the Beo4 batteries, 33
Cleaning the Beo4, 33
Configure Beo4, 34
Customise Beo4, 34
Introducing your television and Beo4, 4
Move extra ‘buttons’, 35
Remove a ‘button’ from the Beo4 list, 35
Replace Beo4 batteries, 33
Using Beo4, 4
Contact Bang & Olufsen, 39
BeoLink
First-time setup
BeoVision in a link room, 18
Connect and operate an audio system, 16
Connect your audio system, 16
Link room operation, 19
Option settings, 18
Use an integrated audio/video system, 17
First-time setup procedure, 27
Camera
Connect a Camera, 24
Copy from a Camcorder to a videotape, 24
Computer monitor
Adjust picture, 30
Bring up the computer image on the screen, 13
Connect a computer, 26
Connections
Connected equipment, 23
Headphones, 24
Loudspeakers, 25
Mains connection, 23
Register additional video equipment, 28
Socket panel, 25
Sockets for temporary connections, 24
Displays and menus
Displayed information and menus, 5
Menu overview, 8
DVD
Use a DVD player, 12
Format
Change the picture format, 7
Headphones
Connect headphones, 24
Language
Choose menu language, 32
First-time setup – choose menu language, 27
Loudspeakers
Change speaker balance or combination, 6
Connect speakers, 25
Sound adjustments, 31
37
Maintenance
Change Beo4 batteries, 33
Handling your television, 22
Maintenance of your television, 33
Picture screen, 33
Peripheral Unit Controller
Connect additional equipment, 25–26
Peripheral Unit Controller menu, 10
Universal Beo4 operation, 11
Use equipment in a link room, 11
Use equipment menus, 11
Picture
Adjust brightness, colour or contrast, 30
Change the picture format, 7
Remove the picture from the screen, 30
Placement
Set up your television, 22
Socket panel
Camera and headphones sockets, 24
Socket panel, 25
Sound
Adjust or mute the sound, 6
Adjust volume, bass or treble, 31
Change speaker balance or combination, 6
38
For your information …
Your needs as a user are given careful
consideration during the design and
development process of a Bang & Olufsen
product and we strive to make our products
easy and comfortable to operate.
Therefore, we hope that you will take the
time to tell us about your experiences with
your Bang & Olufsen product. Anything
which you consider important – positive or
negative – may help us in our efforts to
refine our products.
Thank you!
To contact us, visit our web-site on:
www.bang-olufsen.com
or write to:
Bang & Olufsen a/s
BeoCare
Peter Bangs Vej 15
DK–7600 Struer
or fax:
Bang & Olufsen
BeoCare
+45 9785 3911 (fax)
This product is in conformity with the
provisions of the Directives 1999/5/
EC and 2006/95/EC.
HDMI, the HDMI logo and High-Definition
Multimedia Interface are trademarks or registered
trademarks of HDMI Licensing LLC.
For the US-market only!
NOTE: This equipment has been tested and found
to comply with the limits for a class B digital device,
pursuant to part 15 of the FCC Rules. These limits
are designed to provide reasonable protection
against harm­ful interference in a residential
­installation.
This equipment generates, uses and can radiate
radio frequency energy and, if not installed and
used in ­accordance with the instructions, may
cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the equip­ment off and on, the
user is ­encouraged to try to correct the
­interference by one or more of the following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment
and receiver.
– Connect the equipment into an outlet on a
circuit different from that to which the receiver
is connected.
– Consult the retailer or an experienced radio/TV
technician for help.
For the Canadian market only!
This class B digital apparatus meets all require­
ments of the Canadian Interference-Causing
Equipment Regulations.
Technical specifications, features and the use
thereof are subject to change without notice.
3509838
0710
www.bang-olufsen.com
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement