INSTRUCTION MANUAL GUIDE D’UTILISATION PCB104E

INSTRUCTION MANUAL GUIDE D’UTILISATION PCB104E
INSTRUCTION MANUAL
PORTABLE STEREO RADIO CD PLAYER
WITH AUX IN
GUIDE D’UTILISATION
LECTEUR CD PORTATIF AVEC RADIO STÉRÉO
ET ENTRÉE AUXILIAIRE
PCB104E
Before operating, please read these instructions carefully!
Veuillez lire attentivement le présent guide avant d’utiliser l’appareil.
IMPORTANT SAFETY INSTRUCTIONS
WARNING:
TO PREVENT FIRE OR SHOCK HAZARD DO NOT USE THIS PLUG WITH AN EXTENSION
CORD, RECEPTACLE OR OTHER OUTLET UNLESS THE BLADES CAN BE FULLY
INSERTED TO PRESENT BLADE EXPOSURE. TO PREVENT FIRE OR SHOCK HAZARD.
DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.
This lightning flash with
arrowhead symbol, within
an equilateral triangle, is
intended to alert the user to
the presence of insulated
dangerous voltage within
the products enclosure that
may be of sufficient
magnitude to constitute a
risk of electric shock
presents
Warning: to reduce the risk of
electric shock, do not remove
cover (or back) no user serviceable part inside.
Refer servicing to qualified
service personnel.
1.
2.
3.
4.
5.
6.
7.
The exclamation point
within
an
equilateral
triangle is intended to alert
the user to the presence of
important operating and
maintenance
(servicing)
instructions in the literature
accompanying
the
appliance.
Read these instructions.
Keep these instructions.
Heed all warnings.
Follow all instructions.
Do not use this apparatus near water.
Clean only with dry cloth.
Do not block any ventilation openings. Install in accordance with the manufactures
instructions.
8. Do not install near any heat sources such as radiators, heat registers, stoves, or other
apparatus (including amplifiers) that produce heat.
9. Unplug the apparatus during lightening storms or when unused for long periods of time.
10. This appliance shall not be exposed to dripping or splashing water and that not object filled
with liquids such as vases shall be placed on apparatus .
1
IMPORTANT
Since CD circuitry may cause interference to other radio or television tuners nearby, switch this
unit off when not in use or move it away from the affected radio tuner.
NOTE: This digital apparatus does not exceed the Class B limits for radio noise emissions
from digital apparatus as set out in the Radio Interference Regulations of Industry Canada.
These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to radio or
television operation (which can be determined by turning the equipment off), the user is
encouraged to try to correct the interference by one or more of the following measures:
•
•
•
•
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
Consult the dealer or an experienced radio / TV technician for help.
2
3
NAMES OF CONTROLS
13.
14.
15.
16.
17.
18.
19.
20.
21.
22.
23.
24.
25.
1.
2.
3.
FOLDING HANDLE
CD COMPARTMENT
CD SKIP/SEARCH BACKWARD
BUTTON
4. CD RANDOM BUTTON
5. CD SKIP/SEARCH FORWARD
BUTTON
6. CD STOP BUTTON
7. CD REPEAT INDICATOR
8. POWER INDICATOR
9. CD LED DISPLAY
10. FM STEREO INDICATOR
11. CD REPEAT BUTTON
12. CD PLAY/PAUSE BUTTON
SPEAKERS
BASS BOOST BUTTON
CD PROGRAM BUTTON
CD PROGRAM INDICATOR
FM TELESCOPIC ANTENNA
FUNCTION SWITCH
VOLUME CONTROL
AUX INPUT JACK
DIAL SCALE
BAND SELECTOR
TUNING CONTROL
AC SOCKET
BATTERY COMPARTMENT
INTRODUCTION
• Please read through these operating instructions, so you will know how to operate your
equipment properly. After you finished reading the instructions manual, put it away in a safe
place for future reference.
CAUTION:
• Do not block the ventilation openings or holes.
• Do not place any naked flame sources, such as lighted candles, on the apparatus.
• Invisible laser radiation when open and interlock failed or defeated. Avoid direct exposure to
beam.
• To prevent fire or shock hazard, do not expose this appliance to rain or moisture.
IMPORTANT FOR LASER PRODUCTS
REPRODUCTION OF LABELS
1. CLASSIFICATION LABEL, PLACED ON REAR ENCLOSURE.
CLASS 1 LASER PRODUCT
PRODOTTO LASER CLASSE1
KLASS 1 LASERAPPARAT
2. WARNING LABEL, PLACED INSIDE THE UNIT.
CAUTION: Do not open the unit. There are no user serviceable parts inside the unit; consult all
servicing to qualified service personnel.
Discs for Playback
This system can playback all digital audio CD, finalized digital audio CD-Recordable (CD-R)
discs, finalized digital audio CD-Rewritable (CD-RW) discs and CD-DA format digital audio
CD/CD-R/CD-RW discs.
4
POWER SOURCE
This unit is designed to be operated on AC/DC.
AC OPERATION
Plug the smaller end of AC power cord into AC jack on unit and the other bigger end into AC wall
outlet. The batteries will be automatically disconnected.
DC OPERATION
Open the BATTERY COMPARTMENT DOOR. Install 6 pcs UM-2/C size batteries (not included)
into compartment. Please follow correct polarities as indicated.
CAUTION
• Remove batteries if they are flat or not being used for a long period of time.
• Batteries contain chemical substances, so they should be disposed of properly.
BASIC FUNCTION
SWITCHING ON THE UNIT
Set the FUNCTION switch to CD or RADIO.
TO ADJUST VOLUME
Rotate the VOLUME CONTROL back and forth to increase and decrease volume.
BASS BOOST SYSTEM
For more extra bass, press the BASS BOOST button. Press again to turn off bass.
USING THE RADIO
TUNING IN RADIO STATIONS
1.
2.
3.
4.
5.
Move the FUNCTION switch to RADIO position, the POWER indicator will illuminate.
Slide the BAND switch to select the desired wave band: AM, FM, FM ST..
Tune to required station by rotating the TUNING KNOB.
Rotate the VOLUME CONTROL to comfortable volume level.
Extend the TELESCOPIC ANTENNA to its full length if you are listening to FM broadcasting.
Gently rock the unit back and forth to get the best reception when you are listening to AM
program, or place the unit in an open place.
Note: If the broadcasting program is too noisy when you are listening to FM stereo station,
please slide the BAND switch to FM. The FM STEREO indicator will be on if you are
receiving FM stereo program.
6. Turn off the radio by switching the FUNCTION switch to "OFF" position
USING THE CD
LOADING A DISC
1.
2.
3.
4.
Set the FUNCTION switch to CD position.
Open the CD door.
Place an audio CD into the tray with the label side facing up.
Close the CD door, the total number of tracks will appear on the display after several
seconds.
4
5. To remove the CD, press OPEN to open CD compartment lid, grasp the CD by its edges,
and carefully take it out.
Note:
• To ensure good system performance; wait until the disc tray completely reads the disc before
proceeding.
• If no disc is loaded into the compartment, or the disc is placed upside down, the display will
show “00 ”.
PLAYING A DISC
1. Press the PLAY/PAUSE button to start playback. The playback starts from track 1, the
PLAY/PAUSE indicator on the right lower corner of the display illuminates.
2. To interrupt playback, press the PLAY/PAUSE button. The PLAY/PAUSE indicator flashes on
and off.
3. To resume playback, press the PLAY/PAUSE button again, the PLAY/PAUSE indicator
becomes steady on the display.
4. To stop playback, press the STOP button, the total number of tracks appears on the display.
SELECTING A DESIRED TRACK/PASSAGE
To select a desired track
• Press the CD SKIP/SEARCH FORWARD/BACKWARD button repeatedly in stop mode or
during play until the desired track appears on the display.
• Press the PLAY/PAUSE button to start play.
To search for a particular passage during playback (track scanning at high speed)
Press and hold the CD SKIP/SEARCH FORWARD/BACKWARD button to scan the current
playing track at high speed until desired point passage, then release the button.
Playback will start again from this point.
PROGRAM TRACKS
Programming tracks of disc are possible when playback is stopped. Up to 20 tracks can be
stored in the memory in any order.
1. In stop mode, press the PROGRAM button, the “01 ” will flash and the PROGRAM indicator
will be on.
2. Press the CD SKIP/SEARCH FORWARD button to select the first desired track to be
programmed.
3. Press the PROGRAM button to enter. The display changes to show “02 ” flashing.
4. Repeat steps 2 & 3 to store other desired tracks until all tracks are programmed.
5. Press the PLAY/PAUSE button to start playback from the first programmed track.
6. Press the STOP button to stop program playback.
Note: Program function can only be done in stop mode.
To Erase the Memory (Program)
To clear the program, you have two options:
1. Press the STOP button when the disc is stopped, or
2. Open the CD compartment lid, program will be erased.
REPEAT
You can play one track or all tracks on the disc repeatedly.
To Repeat a Single Track
1. Press the REPEAT button once during play, the CD REPEAT indicator will flash on and off.
The current track will be played over and over again till you press the STOP button.
2. To cancel repeat play, press the REPEAT button twice. The CD REPEAT indicator turns off.
5
To repeat all Tracks
1. Press the REPEAT button twice during play, the CD REPEAT indicator becomes steady on,
all tracks on the disc will be played over and over again till you press the STOP button.
2. To cancel repeat play, press the REPEAT button once, the CD REPEAT indicator turns off.
Note: Repeat function also can be done in stop mode.
RANDOM PLAY
Press the CD RANDOM button in stop mode, press the CD PLAY/PAUSE button, the unit will
play starting from any track selected by the unit in random order until all tracks are played and
then stop.
AUXILIARY INPUT OPERATION
This unit has provided an AUX INPUT jack, through the jack other audio sources may
connected to this unit and be amplified.
1. Switch the FUNCTION switch to AUX.
2. Connect the audio cable into the AUX. INPUT jack . And the other ends of the cable into the
AUDIO OUT jack on the external audio source.
3. Press PLAY of the external audio source (eg. audio player) to start playback.
4. Adjust the volume by the VOLUME control of this unit.
SPECIFICATIONS
CD SECTION
Channels:
Optical pick-up:
Frequency Response:
2 channels
3 beams laser
100Hz - 16KHz
RADIO SECTION
Receiving Band:
Tuning Range:
Antenna:
AM/FM
AM: 520 - 1710 KHz
FM:
88 - 108 MHz
FM rod antenna, AM built-in ferrite bar
GENERAL
Output Power:
Phones jack:
Power Source:
Power Consumption:
1.2 W x 2 (RMS)
3.5mm
AC 120V ~ 60Hz
DC 9V 1.5V UM-2/C x 6pcs
13.5W
Note: Specifications are subject to change for continuous improvement without prior notice.
6
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement