7160-0033 Install
INSTALLATION INSTRUCTIONS
Product
Universal SeatMount
7170-0126 SeatMount w/Arm & NOTEPAD™V
7170-0127 SeatMount w/Arm & NOTEPAD™V-LT
7160-0033 SeatMount Base
Revision
Form #
Rev. C
INST-324
Printing Spec: PS-001
WARNING
•You must read and follow all of these installation instructions. Failure to follow all of
these installation instructions may result in serious bodily injury or death.
•Do not install or use the Arm Assembly in the area in which the airbag on the vehicle will
be deployed if it is activated. The installer and user of the Universal SeatMount are
responsible for installing and using the Arm Assembly outside the area in which an airbag
will be deployed if activated. (See Product Mounting Disclaimer Below)
•Keep these installation instructions with the product and readily available in the vehicle
for future reference of other users of the product.
•Additional copies of the installation instructions can be obtained from Gamber-Johnson.
If you need assistance or have any questions, call Gamber-Johnson at 1-800-456-6868.
•Do not remove warning label from product under any circumstances.
Remove SeatMount, Arm Assembly and
Notepad™ from shipping boxes.
Attach Arm Assembly to bottom side of
Notepad™ with (4) .25-20 Hex Head Screws
and (4) .25 Flat Washers using a 7/16"
wrench or socket.
Attach Arm Assembly to SeatMount with (3)
.25 Flat Washers and (3) .25-20 Nylok Nuts.
Product Mounting Disclaimer
Gamber-Johnson is not liable under any theory of contract or tort law for any loss, damage, personal injury, special, incidental or consequential damages for personal injury or other damage
of any nature arising directly or indirectly as a result of the improper installation or use of its products in vehicle or any other application. In order to safely install and use Gamber-Johnson
products full consideration of vehicle occupants, vehicle systems (i.e., the location of fuel lines, brakes lines, electrical, drive train or other systems), air-bags and other safety equipment is
required. Gamber-Johnson specifically disclaims any responsibility for the improper use or installation of its products not consistent with the original vehicle manufactures specifications
and recommendations, Gamber-Johnson product instruction sheets, or workmanship standards as endorsed through the Gamber-Johnson Certified Installer Program.
© copyright 2012 Gamber-Johnson, LLC
If you need assistance or have questions, call Gamber-Johnson at 1-800-456-6868
1/3
Adjust the Notepad™ to the correct size and
locate holddown clips, for the computer
being held, according to the Instruction
Sheet supplied with the Notepad™.
Place assembled SeatMount on the center of
the passenger seat.
Depress latch on each Cam Buckle and loosen,
but do not remove the nylon straps.
Insert BackUp Plate thru gap between seat and
seatback.
On vehicles with leather or vinyl seats placing
a towel between the SeatMount and the
seatback will prevent marking the upholstery.
Position BackUp Plate against back of seat,
centering along the line where seat and seat
back meet, as shown.
Pull both Nylon Straps out from the front of
SeatMount while pushing the SeatMount down
into the seat and seatback.
Both straps should be pulled tightly until the
SeatMount is held firmly against the seat with
as little side to side movement as possile.
2/3
Insert computer into Notepad™ mount.
The Arm Assembly and Notepad™ can now be
swiveled toward the driver for best access
during use.
Moving the passenger seat forward or back
can also aid in positioning.
When the computer is not being used or when
the vehicle is in motion, position the Arm
Assembly and Notepad™ over the SeatMount
and agianst the seatback as shown.
WARNING
•The Arm Assembly and Notepad™ should not be positioned in the area where the airbag will be
deployed if it is activated. DO NOT position the equipment in front of an airbag. Equipment
positioned in front of an airbag can cause serious injury or death if an airbag was activated,
such as in an accident.
•If installation of the equipment requires that the equipment be placed in front of an airbag,
deactivate the airbag in the vehicle so it cannot be activated in an accident. In order to
secure permission for deactivating the airbag in these circumstances, contact the National
Highway Traffic Safety Administration at 1-800-424-9393 to gain permission to do so. If you
have any questions or need assistance, call Gamber-Johnson at 1-800-456-6868.
•High speed vehicle turns may cause the arm to swivel, interfering with the driver or other
equipment.
The SeatMount can be quickly removed,
allowing use of the passenger seat.
Depress the latch on each Cam Buckle and
loosen each nylon strap enough to allow
bringing the BackUp Plate out, from behind the
seatback, thru the gap between seat and
seatback.
Lift SeatMount off passenger seat and store in
vehicles' backseat or trunk.
3/3
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement