Shark | S3901UKJR | Specifications | Shark S3901UKJR Specifications

Shark S3901UKJR Specifications
LIFT-AWAY™ PRO STEAM
POCKET® MOP
S3901UKJR
OWNER’S GUIDE
S3901UKJR_11_IB_E_120411_3.indd 1
12-04-11 3:51 PM
IMPORTANT SAFETY INSTRUCTIONS
For Household Use Only
WHEN USING YOUR SHARK®
STEAM MOP, BASIC SAFETY
PRECAUTIONS SHOULD ALWAYS
BE FOLLOWED, INCLUDING THE
FOLLOWING:
READ ALL INSTRUCTIONS BEFORE
USING YOUR SHARK® STEAM MOP.
DANGER OF SCALDING.
Please use caution when using the steam
mop. The steam emitted from the steam
mop is very hot.
IMPORTANT:
This appliance is not intended for use by
persons (including children) with reduced
physical, sensory or mental capabilities
or lack of experience and knowledge,
unless they have been given supervision
or instruction concerning the use of the
appliance by a person responsible for their
safety.
Children should be supervised to ensure
that they do not play with the appliance.
WARNING:
TO REDUCE THE RISK OF FIRE, ELECTRIC
SHOCK OR INJURY:
1.
Use the system only for its intended use.
2. DO NOT use outdoors.
3.
DO NOT leave the appliance unattended
when plugged in. Always unplug the power
cord from the electrical outlet when not in
use and before servicing.
4. DO NOT allow the appliance to be used by
children. Close attention is necessary when
used by or near children, pets or plants.
5. Children should be supervised to ensure that
they do not play with the appliance.
6. Use only as described in this manual.
7 . Use only manufacturer’s recommended
accessories.
8. DO NOT operate the appliance with a
damaged plug or cord, or if the unit has
been dropped or damaged. To avoid the
risk of electric shock, do not disassemble
or attempt to repair the appliance on your
own. If the supply cord is damaged, it must
be replaced by a qualified electrician in order
to avoid a hazard. Incorrect re-assembly or
repair can cause a risk of electrical shock
or injury to persons when the appliance is
used.
9. To protect against a risk of electric shock,
DO NOT immerse the steam mop into
water or any other liquids.
10.DO NOT handle plug or steam mop with
wet hands or operate appliance without
shoes.
11. DO NOT pull or carry by power cord, use
power cord as handle, close a door on the
power cord, or pull the power cord around
sharp edges or corners. Keep power cord
away from heated surfaces.
www.sharkclean.co.uk
S3901UKJR_11_IB_E_120411_3.indd 2
12-04-11 3:51 PM
12.DO NOT unplug by pulling on power
cord. To unplug, grasp the plug not the
power cord. Do not use extension cords or
outlets with inadequate current carrying
capacity.
13.DO NOT put any objects into openings.
Do not use with any opening that is
blocked.
14.DO NOT put hands or feet under the
steam mop. Unit gets very hot.
15.Use ONLY on flat, horizontal surfaces. Do
not use on walls, counters or windows.
16.DO NOT use on leather, wax polished
furniture or floors, synthetic fabrics,
velvet or other delicate, steam sensitive
materials.
17. Liquid or steam must not be directed
towards equipment containing electrical
components, such as the interior of ovens.
18.DO NOT add cleaning solutions, scented
perfumes, oils or any other chemicals to
the water used in this appliance as this
may damage the unit or make it unsafe for
use. If you live in a hard water area, we
recommend using distilled water in your
steam mop.
19. When in use, NEVER turn the appliance
over or on its side. NEVER DIRECT
STEAM TOWARDS PEOPLE,
ANIMALS OR PLANTS.
20.NEVER LEAVE THE STEAM MOP
IN ONE SPOT ON ANY SURFACE
FOR ANY PERIOD OF TIME WHEN
THE CLEANING PAD IS ATTACHED
AS THIS WILL DAMAGE YOUR
FLOORS.
21. Carefully remove the cleaning pad
immediately after you have unplugged and
allowed the steam mop to cool.
22.When cleaning the steam mop, unplug
the power cord from the electrical outlet
and clean with a dry or damp cloth. Do
not pour water or use alcohol, benzene or
paint thinner on the unit.
23.Extreme caution should be exercised when
using this appliance to clean stairs.
24.Never use steam mop without the cleaning
pad attached.
25.Keep your work area well lit.
26.Store steam mop indoors in a cool, dry
place.
27. To avoid circuit overload, do not operate
another appliance on the same socket
(circuit) as the steam cleaner.
28.If an extension cord is absolutely
necessary, an extension cord rated a
minimum of 15 ampere, 14 gage cord
should be used. Cords rated for less
amperage may overheat. Care should be
taken to arrange cord so that it cannot be
pulled or tripped over.
29.DO NOT leave unattended when the
system is connected to a power supply
or electrical outlet. Turn off all controls
before unplugging the unit.
30.DO NOT store unit with damp or wet
cleaning pad attached. Never leave the
steam mop in one spot on any surface for
any period of time with a damp or wet
cleaning pad attached as this will damage
your floors
31. Always unplug and allow the steam mop
to cool before removing or changing mop
heads.
32.Make sure that the water tank door closed
when using the appliance.
WARNING: Your steam mop is
designed to clean hard floor surfaces that
will withstand high heat. Do not use on
unsealed wood or unglazed ceramic floors.
On surfaces that have been treated with
wax or some no wax floors, the sheen may
be removed by the heat and steam action.
It is always recommended to test an
isolated area of the surface to be cleaned
before proceeding. We also recommend
that you check the use and care
instructions from the floor manufacturer.
SAVE THESE
INSTRUCTIONS
www.sharkclean.co.uk
S3901UKJR_11_IB_E_120411_3.indd 3
12-04-11 3:51 PM
This appliance complies with the WEEE-Directive 2002/96/EC on the disposal of electrical and electronic
equipment (WEEE).
This appliance complies with the European directives for electromagnetic compatibility (EMC) 2004/108/EC
and its revisions, as well as Low Voltage Directive (LVD) 2006/95/EC and its revisions.
This marking indicates that this product should not be disposed with other household
wastes throughout the EU. To prevent possible harm to the environment or human health
from uncontrolled waste disposal, recycle it responsibly to promote the sustainable reuse of
material sources. To return your used device, please use the return and collection systems
or contact the retailer where this product was purchased. They can take this product for
environmental safe recycling.
This product has no on/off switch and operates when plugged into the main supply source. Disconnect the
plug from mains after use.
Although the product is not provided with standby mode or off mode, it still fulfills the requirements of
1275/2008/EC - the directive for Eco-Design requirements since according to technical justification, it is
considered as inappropriate to provide standby and off modes when connecting to mains. To reduce energy
consumption be sure to unplug the unit after use.
Guarantee: This product is unconditionally guaranteed for one year against all defects of workmanship and
materials. This guarantee does not affect your statutory rights. If this product proves unsatisfactory please
contact our customer service department on freephone 0800 781 7831.
This manual covers model number:
S3901UKJR 11
TECHNICAL SPECIFICATIONS
Voltage:
220-240V~, 50/60Hz.
Power:
1550 Watts
Water Capacity: 300ml
Not to be disposed
of with other
household waste.
IPX4
www.sharkclean.co.uk
S3901UKJR_11_IB_E_120411_3.indd 4
12-04-11 3:51 PM
Contents
Thank you for
purchasing
the Shark®
Lift-Away™ Pro
Steam Pocket®
Mop.
Getting Started.................................................................................................... 2
Getting Started With Your Steam Mop................................................................. 3
Using Your Steam Mop......................................................................................... 5
Using Your Carpet Glider...................................................................................... 8
Getting Started With Your Removable Handheld Steamer.................................... 9
Using Your Removable Handheld Steamer with Direct Steam Nozzle.................. 10
Using Your Removable Handheld Steamer with Crevice Tool............................... 11
Using Your Removable Handheld Steamer with Window Squeegee..................... 12
Using Your Removable Handheld Steamer with Accessory Hose.......................... 13
Using Your Removable Handheld Steamer with Flat Scrubber.............................. 14
Care of Your Steam Mop...................................................................................... 15
Troubleshooting Guide......................................................................................... 17
www.sharkclean.co.uk
S3901UKJR_11_IB_E_120411_3.indd 1
1
12-04-11 3:51 PM
Getting Started
When assembling your steam mop there may be a little water in or around the water tank. This is because we
test all our steam mops 100% before you buy them, so you get a quality Shark® Lift-Away™ Pro Steam
Pocket ® Mop.
a
h
i
j
k
l
m
d
b
c
n
o
e
f
g
a
b
c
d
e
f
g
Mop Handle
Steam Trigger
Removable Handheld Steamer
Handheld Steamer Housing
All-Purpose Mop Head
Two-Sided All-Purpose Cleaning Pad
for the All-Purpose Mop Head (x2)
Carpet Glider
2
h
i
j
k
l
m
n
o
p
Direct Steam Nozzle
Accessory Hose
Detail Brush
Window Squeegee
Flat Scrubber Tool
All-Purpose Scrubber Pad for Flat
Scrubber Tool
Filling Flask
(1) 6mm x 48mm Large Screw*
Tote Bag (not shown)
*Phillips or flat head screwdriver can be used. Screwdriver
not included.
www.sharkclean.co.uk
S3901UKJR_11_IB_E_120411_3.indd 2
12-04-11 3:51 PM
Getting Started with Your Steam Mop
fig. 1
IMPORTANT: Always make sure the mop is
UNPLUGGED from the wall when not in use.
Never fill the mop, attach the mop head, change
or remove the cleaning pad when the mop is
plugged into the wall. To prolong the life of your
Shark® Lift-Away™ Pro Steam Pocket ®
Mop we recommend using distilled water. Make
sure you only add water to the tank. Chemicals
or cleaning solution may damage the appliance
and could be unsafe for you and your family.
fig. 2
STEAM MOP ASSEMBLY
1Insert the Mop Handle end labeled “Front” into
the Steam Mop Housing. Make sure it is inserted
past the line printed on the pole. Secure the
assembled handle and pole by using the large
screw and a Phillips or a flat head screw driver
(screwdriver not included). (fig. 1)
2Insert the Handheld Steamer into the Steam Mop
Housing. (fig. 2)
www.sharkclean.co.uk
S3901UKJR_11_IB_E_120411_3.indd 3
3
12-04-11 3:51 PM
Getting Started with Your Steam Mop - cont’d
fig. 3
fig. 5
fig. 6
fig. 4
3Use the lavender loop on the side of the cleaning
pad to slide the mop head into the pad pocket.
Then secure the quick fasteners on the top of the
pocket to lock in place. (fig. 3)
4Snap the mop head into the mop body by lining
up the groove on the back of the mop body with
the groove on the back of the mop head. Push
until you hear it latch into place. (fig. 4)
5Turn the water tank cap counter clockwise and
remove from the tank. (fig. 5)
Use the filling flask and pour water into the tank.
Do not overfill. Replace the cap on the water
tank. (fig. 6)
4
IMPORTANT: Do not use on unsealed wood
or unglazed ceramic floors. On surfaces that
have been treated with wax or some no wax
floors, the sheen may be removed by the heat
and steam action. It is always recommended to
test an isolated area of the surface to be cleaned
before proceeding. We recommend that you
check the use and care instructions from the
floor manufacturer.
NOTE: To prolong the life of your Steam Mop, we
recommend using distilled water.
www.sharkclean.co.uk
S3901UKJR_11_IB_E_120411_3.indd 4
12-04-11 3:51 PM
Using Your Steam Mop
IMPORTANT: Make sure you do not use the
mop without attaching a cleaning pad and
adding water to the tank first. When you are
using the mop for the first time, it might take
longer than the normal 30 seconds to start
steaming.
fig. 8
fig. 7
NOTE: Sweep or vacuum your floors prior to
cleaning with your Steam Mop.
1Pull and twist the quick release cord holder to
unwrap the power cord completely. Plug into a
220-240-volt electrical outlet. (fig. 7)
2The ON/STEAM SETTING button will be blue.
If the light does not turn on, reference the
troubleshooting section on page 17. (fig. 8)
www.sharkclean.co.uk
S3901UKJR_11_IB_E_120411_3.indd 5
5
12-04-11 3:51 PM
Using Your Steam Mop - cont’d
fig. 10
fig. 9
3Press the ON/STEAM SETTING button once for
DUST setting (DUST lighted setting indicator will
flash and turn solid blue when it is ready to use).
DUST setting is a light steam for a quick dusting
and best dry time. (fig. 9)
Press the ON/STEAM SETTING button twice for
MOP. MOP setting is for normal, everyday steam
cleaning. (fig. 10)
Press the ON/STEAM SETTING button three
times for SCRUB. SCRUB setting is for heavy
cleaning and will leave floors damp.
After you have selected your desired steam
setting, the setting indicator light will flash and
turn solid blue when it is ready to use.
6
fig. 11
To better understand which steam setting to use
for your cleaning task, see page 7.
4Clean your floors with a forward and backward
motion. (fig. 11)
When you are done, press the ON/STEAM
SETTING button until the light blinks blue as in
standby mode.
NOTE: When using your Shark® Lift-Away™
Pro Steam Pocket ® Mop in MOP mode be
careful not to press the steam trigger on the
Handheld Steamer, as it will activate STEAM
SETTING mode. If this happens, press the ON/
STEAM SETTING button one time to reactivate
your steam selection.
www.sharkclean.co.uk
S3901UKJR_11_IB_E_120411_3.indd 6
12-04-11 3:51 PM
The Shark® Lift-Away™ Pro Steam Pocket® Mop has three unique steam settings so
you can use the perfect amount of steam for the cleaning task at hand. See below for tips on
when to use each setting.
Setting
Ideal for These Surfaces
Laminate
DUST
Bamboo
Hardwood
Recommended Usage
Light cleaning and dusting
Loosen and lift light dirt
Sanitise floors
Marble
MOP
Hardwood
Basic, everyday cleaning
Marble
Remove spots and smaller messes
Tile
Clean moderate and heavily-trafficked areas
Stone
Sanitise floors
Tile
Tough cleaning and removal of stuck-on
messes and stains
Stone
SCRUB
Linoleum
Deep clean heavily-trafficked areas
Cut through heavy dirt and grime
Sanitise floors
Carpet
(with Carpet Glider)
Freshen area rugs and carpets
www.sharkclean.co.uk
S3901UKJR_11_IB_E_120411_3.indd 7
7
12-04-11 3:51 PM
Using Your Steam Mop - cont’d
6When the water tank is empty, the Steam
Mop will stop producing steam. You can refill
the water tank at any time as long as the
mop is unplugged from the outlet. Follow
the instructions from page 4. This applies to
switching the mop head or the cleaning pad as
well.
fig. 12
NOTE: Please wait 2-3 minutes for the Steam
Mop to cool off before switching the mop head
or the cleaning pad. Never leave the Steam Mop
with a damp/wet pad on any floor.
5When one side of the all purpose cleaning pad
gets dirty, just flip the mop and you can quickly
start using the other side. (fig. 12)
Using Your Carpet Glider
fig. 13
The Steam Mop will not clean your carpeting or
area rugs. However, it is great for grooming and
freshening.
fig. 14
THE CARPET GLIDER 1The Carpet Glider can be used with the AllPurpose Head to lightly steam your carpet
and area rugs. Just place the mop head with
the cleaning pad attached into the glider. The
recommended steam setting is SCRUB when
using the Carpet Glider. (fig. 13)
8
2
Move the Steam Mop back and forth across a
section of the carpet. (fig. 14)
www.sharkclean.co.uk
S3901UKJR_11_IB_E_120411_3.indd 8
12-04-11 3:51 PM
Getting Started With Your
Removable Handheld Steamer
Your Shark® Lift-Away™ Pro Steam Pocket ®
Mop is designed to clean surfaces that
will withstand high heat and moisture.
Do not use on unsealed wood surfaces
(especially wooden antique furniture),
unglazed ceramic tile, painted surfaces
or surfaces that have been treated with
wax, oils, varnishes, or shellac. The sheen
may be removed by the heat, steam, and
friction of the cleaning tools. Lacquer and
polyurethane coatings provide a hard
durable protective finish that withstands
moisture, but it is always recommended to
test an isolated area of the surface to be
cleaned before proceeding.
fig. 15
We also recommend you check the use
and care instructions from the surface
manufacturer.
When cleaning finished wood surfaces,
use broad, continuous cleaning strokes. To
prevent surface damage, avoid focusing
steam or allowing the cleaning tools to sit
in one spot for any amount of time.
1To remove the Handheld Steamer, press and
hold down the Handheld Release Buttons while
pulling out the Handheld Steamer. (fig. 15)
www.sharkclean.co.uk
S3901UKJR_11_IB_E_120411_3.indd 9
9
12-04-11 3:51 PM
Using Your Removable Handheld Steamer
with Direct Steam Nozzle
Cleaning Tip: The Direct Steam Nozzle creates direct steam spray to clean and
sanitise hard to reach nooks & crannies and other places where germs may build
up. Use the Direct Steam Nozzle to loosen and dislodge compact dirt often
found in corner and tight places where traditional methods and cleaning tools
tend to push dirt into, making it tough to reach and clean. Spray direct steam
and wipe clean with a wet cloth or paper towel.
fig. 17
fig. 16
FOR SPOT CLEANING AND STEAMING
2First attach the Direct Steam Nozzle by pressing
the nozzle onto the Handheld Steamer until it
clicks into place. (fig. 16)
3The Handheld Steamer is automatically set to
SCRUB mode. Squeeze the steam trigger to
activate steam. To change modes press the ON/
STEAM SETTING button to select either DUST,
MOP or SCRUB mode. You can change the steam
mode while the Handheld Steamer is in standby
or in use. Once the selected setting indicator
light has turned blue, hold down the steam
trigger to start steaming. (fig. 17)
For effective cleaning, hold the steam output
nozzle 1-2 inches away from the surface you’re
cleaning.
10
C AUTION: Do not press the steam trigger until
the Direct Steam Nozzle is snapped into the main
nozzle of your Handheld Steamer.
4To remove the Direct Steam Nozzle, press and
hold down the Handheld Release Buttons. Then
slide out the Direct Steam Nozzle using the grip.
C AUTION: Do not press the steam trigger
while removing the Direct Steam Nozzle. Avoid
touching the tip of the Direct Steam Nozzle, as
this will be very hot after steaming.
NOTE: The Handheld Steamer may continue to
emit steam for a few seconds after the trigger
is released This is normal, and the steaming will
eventually come to a stop.
www.sharkclean.co.uk
S3901UKJR_11_IB_E_120411_3.indd 10
12-04-11 3:51 PM
Using Your Removable Handheld Steamer
with Crevice Tool
Cleaning Tip: Crevice Tool is designed for removing stubborn messes in hard-to-reach
nooks, corners and in grout where focused scrubbing power may be needed. The
Crevice Tool can loosen and dislodge compact dirt often found in corners and tight
places where traditional methods and cleaning tools tend to push dirt into, making
it difficult to reach and clean. Scrub with the Crevice Tool and wipe clean with a
cleaning cloth.
fig. 18
fig. 19
1Attach the Crevice Tool by snapping into the
handle of the Accessory Hose. (fig. 18)
2Select either DUST, MOP or SCRUB mode by
pressing the ON/STEAM SETTING button and
wait until the selected setting indicator light
turns solid blue. Hold down the steam trigger to
start steaming. (fig. 19)
3To remove the Crevice Tool, press and hold down
the Accessory release button. Then slide out the
Crevice Tool.
C AUTION: Do not press the steam trigger
while attaching or removing the Crevice Tool.
www.sharkclean.co.uk
S3901UKJR_11_IB_E_120411_3.indd 11
11
12-04-11 3:51 PM
Using Your Removable Handheld Steamer
with Window Squeegee
Cleaning Tip: To use the window squeegee, work with the vapor jet down using top to
bottom movements. To do this without leaving streaks, use lateral movements from the
top to the bottom of the surface.
fig. 20
fig. 21
C AUTION: Always avoid any sudden changes
in temperature to prevent breakage of cracks in
windows.
3To remove the Window Squeegee, press and
hold down the Accessory release button. Then
slide out the Window Squeegee.
1Attach the Window Squeegee by snapping into
the handle of the Accessory Hose. (fig. 20)
C AUTION: Do not press the steam trigger
while attaching or removing the Window
Squeegee.
2Select either DUST, MOP or SCRUB mode by
pressing the ON/STEAM SETTING button and
wait until the selected setting indicator light
turns solid blue. Hold down the steam trigger to
start steaming. (fig. 21)
12
www.sharkclean.co.uk
S3901UKJR_11_IB_E_120411_3.indd 12
12-04-11 3:51 PM
Using Your Removable Handheld Steamer
with Accessory Hose
fig. 22
fig. 23
1To use the Accessory Hose, first attach the
Accessory Hose to the Handheld Steamer by
snapping the Accessory Hose into the main
nozzle. (fig. 22)
C AUTION: Do not press the steam trigger
while attaching or removing the Accessory Hose.
C AUTION: Do not use the Accessory Hose
without cleaning tools attached.
2Select the desired cleaning tool for use. Follow
the cleaning tool sub-assembly instructions for
the selected tool.
3To remove the Accessory Hose, press and hold
down the Handheld Release Buttons. Then slide
out the Accessory Hose using the grip.
(fig. 23)
www.sharkclean.co.uk
S3901UKJR_11_IB_E_120411_3.indd 13
13
12-04-11 3:51 PM
Using Your Removable Handheld Steamer
with Flat Scrubber
Cleaning Tip: The Flat Scrubber is designed for cleaning a variety of surfaces and is
exceptional on those that are large and flat including counter tops, table tops, walls
mirrors, windows, stairs, shelves and other similar surfaces. Super absorbent bonnet
loosens, lifts, and locks in dirt and grime while sanitising at the same time.
fig. 26
fig. 24
fig. 25
1To attach the All-Purpose Scrubber Pad, place
the pad exterior side down on a flat surface
(lavender tab indicates the bottom of the pad)
and insert the top of the Flat Scrubber Tool into
the top portion of the pad and then pull the pad
over each side of the back edge.
2Press the Flat Scrubber Tool onto the Accessory
Hose until it clicks into place. (fig. 24)
3Select either DUST, MOP or SCRUB mode by
pressing the ON/STEAM SETTING button and
wait until the selected setting indicator light
turns solid blue. Hold down the steam trigger to
start steaming. (fig. 25)
C AUTION: Do not press the steam trigger
while attaching or removing the Flat Scrubber
Tool.
C AUTION: Do not use the Flat Scrubber Tool
without the All-Purpose Scrubber Pad attached.
4To remove the Flat Scrubber Tool, press and hold
down the Accessory Hose release button. Then
slide out the Flat Scrubber Tool. (fig. 26)
14
www.sharkclean.co.uk
S3901UKJR_11_IB_E_120411_3.indd 14
12-04-11 3:51 PM
Care of Your Steam Mop
fig. 28
fig. 27
fig. 29
fig. 30
AFTER USE AND STORAGE
1When you have finished using the Handheld
Steamer, reattach it to the mop by first placing
the bottom of the Handheld Steamer into the
cradle of the mop housing. (fig. 27)
2Then slide the top end of the Handheld Steamer
into the mop housing and snap into place.
NOTE: Make sure all attachments are removed
before reuniting the Handheld Steamer with the
Steam Mop.
4Empty the water tank before storage. Remove the
water tank cap and empty the tank over a sink.
Replace the water cap. (fig. 29)
5To store the Shark® Lift-Away™ Pro Steam
Pocket ® Mop hanging up, first remove the
head (after it has cooled and the steam has been
released) then hang on a large hook. (fig. 30)
3If you have finished mopping, press the ON/
STEAM SETTING button until the LED light blinks
blue. This stops the unit from steaming. Unplug
the cord from the outlet and place the mop into
the upright position. Let the unit cool for 2-3
minutes.
Remove the cleaning pad by releasing the quick
fasteners and using the lavender loop on the
side of the pocket, avoiding contact with the hot
pad or dirt. (fig. 28)
www.sharkclean.co.uk
S3901UKJR_11_IB_E_120411_3.indd 15
15
12-04-11 3:51 PM
Care of Your Steam Mop - cont.
DECALCIFYING YOUR STEAM MOP
Calcium and mineral deposits can build up and
impact the performance of your steam mop
over time. To extend the life of your product we
recommend that you use distilled water.
40°
fig. 31
fig. 33
fig. 32
CARE OF YOUR CLEANING PADS
1We recommend washing your cleaning pad
separately from other fabrics to avoid picking
up lint. Only use liquid detergent (no
powder detergent). Do not use any
fabric softeners or bleach. Line dry. Do not
tumble dry. (fig. 31)
2If there are loose threads on the cleaning pad
carefully cut the thread with scissors. Do not pull
on them or cut at the base.(fig. 32)
IMPORTANT: The cleaning pad may be very
hot from the steam. Use caution when removing.
Let the unit cool for 2-3 minutes.
CLEANING THE NOZZLE
NOTE: To prevent clogging, it is recommended
that you periodically clean the Direct Steam
Nozzle and the extension hose stem with the
cleaning tool provided or a paper clip.
1Your Handheld Steamer should not normally
require cleaning, however, should you notice
a decrease in the steam output, it may be
necessary to remove mineral deposits built up
around the nozzles.
2Unplug the cleaner from the electrical outlet.
3Use the provided nozzle cleaner or a small
diameter stiff metal wire, such as a straightened
metal paperclip, and carefully insert the end of
the wire into the nozzle orifice. See illustration
above. (fig. 33)
4Move the wire back and forth several times to
remove any deposits.
5Plug in the appliance to the power outlet and
test steam output.
ORDERING REPLACEMENT PARTS
To order additional parts and accessories, feel free
to contact us at
JML, Unit 1 Eastside
Port of Tyne
South Shields
NE33 5SP
info@JMLgroup.co.uk
Freephone 0800 781 7831
16
PART
PART NO.
1 2 All Purpose Pockets
XT3901UKJR
www.sharkclean.co.uk
S3901UKJR_11_IB_E_120411_3.indd 16
12-04-11 3:51 PM
Troubleshooting Guide
PROBLEM
The Shark® Lift-Away™
Pro Steam Pocket® Mop
will not turn-on.
The unit will not
make steam.
POSSIBLE REASONS & SOLUTIONS
Your steam mop should be securely plugged into a 220-240V~ electrical
outlet only.
Check your fuse or breaker.
If your unit still does not work, give us a call at: Freephone 0800 781 7831.
Is there water in the water tank? If not, add water to your steam mop
following instructions on page 4.
If the unit still does not make steam, follow the instructions on page 16 to
clean the nozzle.
The Shark® Lift-Away™
Pro Steam Pocket® Mop
leaves water on the floor.
Cannot select steam setting/flashing blue light
remains on.
Check to see if your cleaning pad is too wet. We recommend you unplug the
steam mop and change the cleaning pad.
Make sure the cleaning pad is attached correctly.
If you have already plugged in your unit, unplug and try a different outlet.
This may reset the standby mode.
Add water to the tank and select steam setting by pressing the standby
button.
If your unit still does not work, give us a call at: Freephone 0800 781 7831.
The Shark® Lift-Away™
Pro Steam Pocket® Mop
left a white spot on the floor.
Do not leave your steam mop on the floor with a damp or wet cleaning pad.
If you’re using tap water, we recommend switching to distilled water.
Make sure the cap is securely on the water tank.
The cleaning pad might be dirty. Flip or change the cleaning pad.
If you washed the cleaning pad with powder detergent, then your pad could
be damaged and require replacement.
Floors are cloudy, streaky
or spotty
after steaming.
This could also be an indication of prior soap or grease residue that has
accumulated on the floor. As our steam mops use only a small amount of
water, it may not be wet enough to rinse off the accumulation that the
steam is bringing to the surface. We suggest rinsing the floor with nothing
but water, letting it dry, and then steam mopping again with a clean pad.
One or more rinses generally removes the residue.
A more stubborn case may require you to rinse the floor with a mix of one
part vinegar and two parts water.
The Shark® Lift-Away™
Pro Steam Pocket® Mop
is hard to push.
Make sure the cleaning pad is attached correctly.
Check to see if the cleaning pad is excessively dirty. If so, replace the
cleaning pad.
www.sharkclean.co.uk
S3901UKJR_11_IB_E_120411_3.indd 17
17
12-04-11 3:51 PM
Notes
18
www.sharkclean.co.uk
S3901UKJR_11_IB_E_120411_3.indd 18
12-04-11 3:51 PM
Notes
www.sharkclean.co.uk
S3901UKJR_11_IB_E_120411_3.indd 19
19
12-04-11 3:51 PM
JML, Unit 1 Eastside
Port of Tyne
South Shields
NE33 5SP
info@JMLgroup.co.uk
Freephone 0800 781 7831
www.sharkclean.co.uk
Registered address: JML House, NW5 3EG
Technical Details
Model number: S3901UKJR 11
Input: 1550 Watts
Main unit voltage: 220-240V~, 50/60Hz
Printed in China
Illustrations may differ from actual product.
S3901UKJR.E.120411.3
Not to be disposed
of with other
household waste.
IPX4
S3901UKJR_11_IB_E_120411_3.indd 20
12-04-11 3:51 PM
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising