red lion SFCRD manual

Below you will find brief information for Programming Card CUB5USB, Programming Cable CBLUSB, Programming Kit CUB5USB0, USB Cable CBLUSB00, Programming Software Crimson 2 SFCRUSB. This manual outlines the installation, configuration, and operation of the CUB5USB programming option card. The plug-in card enables you to configure CUB5 on a PC, using the free Crimson 2 software. The card plugs into the main circuit board of the meter and requires USB driver installation, which are included with the software. Following installation of the drivers, the card appears as a Virtual Communications Port. The CUB5USB card, in conjunction with the Crimson 2 software, allows you to configure CUB5 meters from a PC. Crimson offers standard drop-down menu commands, that make it easy to program the CUB5 meters. The CUB5 program can then be saved in a PC file for future use. A CUB5 serial plug-in card is required to program the meter using the software. The CUB5USB programming option card allows you to configure CUB5 meters from a PC. It also requires the Crimson 2 software, which is available as a free download.

PDF Download

Document

Bulletin No. CUB5USB-A
Drawing No. LP0770
Released 10/08
Tel +1 (717) 767-6511
Fax +1 (717) 764-0839
www.redlion.net
MODEL CUB5USB - USB PROGRAMMING OPTION CARD
DESCRIPTION
This bulletin serves as a guide for the installation, configuration and operation
of the CUB5 USB Programming plug-in card for the CUB5. The plug-in card is
a separately purchased option card that plugs into the main circuit board of the
meter. The CUB5USB card in conjunction with the Crimson&reg; programming
software enables the user to configure CUB5 on a PC. The CUB5USB requires
installation of drivers which are included with the Crimson Programming
software. Following installation of the drivers, the card appears as a Virtual
communications port.
Crimson is a Windows&reg; based program that allows configuration of the CUB&reg; 5
meters from a PC. Crimson offers standard drop-down menu commands, that
make it easy to program the CUB5 meters. The CUB5 program can then be
saved in a PC file for future use. A CUB5 serial plug-in card is required to
program the meter using the software.
INSTALLING PLUG-IN CARDS
SPECIFICATIONS
The card plugs into the main circuit board of the meter as shown.
Perform USB driver installation below prior to powering the
CUB5 and connecting CUB5USB to a PC USB port.
CUB5USB PROGRAMMING CARD
Type: USB Virtual Comms Port
Baud Rate: 300 to 38.4k
Unit Address: 0 to 99
CRIMSON 2 SYSTEM REQUIREMENTS
• Windows 2000, XP, or Vista
• RAM and free disk space as required by the chosen operating system.
• An additional 50 MB of disk space for software installation.
• A display of at least 800 by 600 pixels
• A USB port for downloading to the CUB5
USB Card
WARNING: Disconnect all power to the unit before
installing Plug-in card.
ORDERING INFORMATION
CAUTION: The Plug-in cards and main circuit board contain static
sensitive components. Before handling the cards, discharge static
charges from your body by touching a grounded bare metal
object. Ideally, handle the cards at a static controlled clean
workstation. Also, only handle the cards by the edges. Dirt, oil or
other contaminants that may contact the cards can adversely
affect circuit operation.
MODEL NO. DESCRIPTION
CUB5USB
CBLUSB
CUB5USB0
Type A to B USB Cable
CBLUSB00
USB Programming Kit containing USB
SFCRUSB*
Card, USB Cable and Crimson software
Crimson 2 PC Configuration Software for
SFCRD*
Windows 98, ME, 2000 and XP
USB DRIVER INSTALLATION
PART NUMBER
CUB5 USB Programming Card
SFCRUSB0
SFCRD200
* Crimson software is available for download from http://www.redlion.net/
1. Download and install the latest Crimson 2 build on your Windows&reg; compatible
PC. Earlier builds may not have the RLC Virtual Comm port drivers. Crimson
software is available as a free download at http://www.redlion.net.
2. Install CUB5USB card into CUB5 meter and apply power to the CUB5.
3. Connect Type A USB cable to computer and CUB5USB option card.
Windows will prompt you for the location of the drivers for the device. The
default location for these drivers is “C:\Program Files\Red Lion
controls\Crimson 2.0\Device.” When the hardware setup appears, choose
“Install from a list or Specific location,” click Next, and then check “Include
this location...” and click the Browse button. Point the Wizard at the location
specified above or whatever other location you specified during installation
of the software. It is important that you perform this step correctly, or you
may have to manually remove the drivers using the Device Manager, and
repeat the installation once more.
Note: Crimson’s USB drivers have not been digitally signed by Microsoft&reg;,
and you will therefore see a dialog offering you the chance to stop the
installation. You should be sure to select the Continue option to indicate
that you do indeed wish to install the drivers.
4. Windows will automatically assign a comms port to the CUB5USB. To
determine the port assigned, open “System Properties” from within
Windows&reg; Control Panel. Select the Hardware tab, and click the “Device
Manager” button. Expand the “Ports” line. Take note of which Comms port
is assigned to “RLC Virtual Comm port”. It must be Com4 or lower to operate
with Crimson 2. If higher, right-click on the entry and select “Properties,”
“Port Settings” tab, and then “Advanced” button. Select a Coms port that is
COM4 or lower and is not physically being used.
LIMITED WARRANTY
The Company warrants the products it manufactures against defects in materials and
workmanship for a period limited to two years from the date of shipment, provided the
products have been stored, handled, installed, and used under proper conditions. The
Company’s liability under this limited warranty shall extend only to the repair or
replacement of a defective product, at The Company’s option. The Company disclaims
all liability for any affirmation, promise or representation with respect to the products.
The customer agrees to hold Red Lion Controls harmless from, defend, and indemnify
RLC against damages, claims, and expenses arising out of subsequent sales of RLC
products or products containing components manufactured by RLC and based upon
personal injuries, deaths, property damage, lost profits, and other matters which Buyer,
its employees, or sub-contractors are or may be to any extent liable, including without
limitation penalties imposed by the Consumer Product Safety Act (P.L. 92-573) and
liability imposed upon any person pursuant to the Magnuson-Moss Warranty Act (P.L.
93-637), as now in effect or as amended hereafter.
No warranties expressed or implied are created with respect to The Company’s products
except those expressly contained herein. The Customer acknowledges the disclaimers
and limitations contained herein and relies on no other warranties or affirmations.
1
MODULE 5 - SERIAL COMMUNICATIONS PARAMETERS (5-SEr)
PARAMETER MENU
* - Disregard these parameters when configuring unit to upload or download wth Crimson.
Module 5 is the programming module for the Serial Communications
Parameters. The only paramters of concern when utilizing the CUB5USB
programming option card to communicate with Crimson 2 programming
software is the Baud Rate and Meter Address. The Parameters are only
accessible when an optional CUB5USB, RS232 or RS485 serial
communications card is installed in the meter.
Indicates Program Mode Alternating Display.
Parameter
C&quot;6E &laquo;
&ordf; METER ADDRESS
Addr
&laquo;
&ordf;
00
0
to
99
Enter the serial node address. With a single unit, an address is not needed
and a value of zero can be used (RS232 applications). Otherwise, with multiple
bussed units, a unique address number must be assigned to each meter. The
node address applies specifically to RS485 applications.
Selection/Value
ABBREVIATED PRINTING *
Factory Settings are shown.
BAUD RATE
Abbr
&laquo;
&ordf;
NO
NO
YES
Set the baud rate to match that of other serial communications equipment.
Normally, the baud rate is set to the highest value that all of the serial
communications equipment is capable of transmitting and receiving.
This parameter determines the formatting of data transmitted from the meter
in response to a Transmit Value command or a Block Print Request. Select NO
for a full print transmission, consisting of the meter address, mnemonics, and
parameter data. Select YES for abbreviated print transmissions, consisting of the
parameter data only. This setting is applied to all the parameters selected in the
PRINT OPTIONS. (Note: If the meter address is 0, the address will not be sent
during a full transmission.)
DATA BIT *
PRINT OPTIONS *
bAUd
&ordf;
dAtA
&ordf;
&laquo;
9600
&laquo;
300
600
7-bit
1200
2400
4800
9600
19200
38400
8-bit
7-bit
Select either 7- or 8-bit data word length. Set the word length to match the
other serial communications equipment on the serial link.
PARITY BIT*
PAr
&laquo;
&ordf;
Odd
NO
Odd
EVEN
This parameter only appears when the Data Bit parameter is set to a 7-bit
data word length. Set the parity bit to match that of the other serial equipment
on the serial link. The meter ignores parity when receiving data and sets the
parity bit for outgoing data. If parity is set to NO, an additional stop bit is used
to force the frame size to 10 bits.
OPt
&laquo;
&ordf;
NO
NO
YES
This parameter selects the meter values transmitted in response to a Print
Request. A print request is also referred to as a block print because more than
one parameter can be sent to a printer or computer as a block.
Selecting YES displays a sublist for choosing the meter parameters to appear
in the print block. All active parameters entered as YES in the sublist will be
transmitted during a block print. Parameters entered as NO will not be sent.
The “Print All” (P-ALL) option selects all meter values for transmitting (YES),
without having to individually select each parameter in the sublist.
Note: Inactive parameters will not be sent regardless of the print option
setting. For example, the Setpoint value(s) will not be sent unless an optional
setpoint card is installed in the meter.
* - Disregard these parameters when configuring unit to upload or download wth
Crimson software.
Red Lion Controls AP
Red Lion Controls
20 Willow Springs Circle
Red Lion Controls BV
Printerweg 10
Unit 101, XinAn Plaza
Building 13, No.99 Tianzhou Road
York PA 17406
NL - 3821 AD Amersfoort
Tel +1 (717) 767-6511
Tel +31 (0) 334 723 225
Tel +86 21 6113-3688
Fax +1 (717) 764-0839
Fax +31 (0) 334 893 793
Fax +86 21 6113-3683
ShangHai, P.R. China 200223
">

Hello! I am an AI chatbot specifically trained to assist you with the red lion SFCRD manual. I have thoroughly reviewed the document and can help you locate the exact information you need or explain the content in clear and simple terms. Whether you’re looking for guidance on specific features, troubleshooting steps, or general usage, feel free to ask your questions. The more details you provide about your concerns or needs, the more accurately and effectively I can assist you!

Show related prompts

Assistant typing

Assistant terminated

Key features

USB Programming Option Card
Crimson 2 Software
Virtual Communications Port
Easy to configure CUB5 Meters
Save program to PC
Free download

Frequently asked questions

First, download and install the latest Crimson 2 build on your Windows compatible PC. Then, install the CUB5USB card into the CUB5 meter and apply power to the CUB5. Connect the USB cable to your computer and the CUB5USB option card. Windows will prompt you for the location of the drivers for the device. The default location for these drivers is “C:\Program Files\Red Lion controls\Crimson 2.0\Device.”

Crimson 2 requires Windows 2000, XP, or Vista, RAM and free disk space as required by the chosen operating system, an additional 50 MB of disk space for software installation, a display of at least 800 by 600 pixels, and a USB port for downloading to the CUB5.

Open System Properties' from within Windows Control Panel. Select the Hardware tab, and click the 'Device Manager' button. Expand the 'Ports' line. Take note of which Comms port is assigned to 'RLC Virtual Comm port'. It must be Com4 or lower to operate with Crimson 2. If higher, right-click on the entry and select 'Properties,' 'Port Settings' tab, and then 'Advanced' button. Select a Coms port that is COM4 or lower and is not physically being used.