BAND-IT J93099 Cutter Blade Kit

BAND-IT J93099 Cutter Blade Kit
Installation
Instructions
J93099
Cutter Blade Kit
J93099 Kit Installation Instructions for Cutter blade and Backing Plate
Components of this kit are a dimensionally matched set. You may have parts that look similar, but they are different
dimensionally if received before May 1st, 2004. Parts received before May 1st , 2004 should be discarded.
1.
2.
3.
4.
Remove old cutter blade screws, cutter blade and backing plate and discard.
See illustrations to determine the correct positions for component assembly.
Hold cutter blade and backing plate together, insert screws and tighten to 8-14 ft-lbs.
Choose the correct length bolts supplied in this kit for your tool. Fully tensioned bolts should flush or extend beyond
the cutter blade ¼” max.
Operating Tip: Keep the bolts tight (8-14 ft-lbs.). A loose bolt may cause cracking or premature wear of the cutter blade
and/or backing plate. This could result in improper clamp tensioning, locking, and cutting.
Operating Tip: Keep the leading edges of the cutter blade and backing plate free of metal shavings. Metal shavings will
result in clamp band gouging during tensioning. Clean and hone the leading edges by hand. Do not use power tools.
Honing should polish surfaces, not remove material.
BAND-IT-IDEX, Inc.
A Unit of IDEX Corporation
4799 Dahlia Street
Denver, CO 80216-3070 USA
P: 1-800-525-0758
F: 1-800-624-3925
www.BAND-IT-IDEX.com
Document # P15488 Rev. D
© Copyright
BAND-IT-IDEX, Inc. 2007
All rights reserved
Page 1 of 2
Installation
Instructions
J93099
Cutter Blade Kit
J93099 Kit Installation Instructions for Cutter blade and Backing Plate
Components of this kit are a dimensionally matched set. You may have parts that look similar, but they are different
dimensionally if received before May 1st, 2004. Parts received before May 1st , 2004 should be discarded.
1.
2.
3.
4.
Remove old cutter blade screws, cutter blade and backing plate and discard.
See illustrations to determine the correct positions for component assembly.
Hold cutter blade and backing plate together, insert screws and tighten to 8-14 ft-lbs.
Choose the correct length bolts supplied in this kit for your tool. Fully tensioned bolts should flush or extend beyond
the cutter blade ¼” max.
Operating Tip: Keep the bolts tight (8-14 ft-lbs.). A loose bolt may cause cracking or premature wear of the cutter blade
and/or backing plate. This could result in improper clamp tensioning, locking, and cutting.
Operating Tip: Keep the leading edges of the cutter blade and backing plate free of metal shavings. Metal shavings will
result in clamp band gouging during tensioning. Clean and hone the leading edges by hand. Do not use power tools.
Honing should polish surfaces, not remove material.
BAND-IT-IDEX, Inc.
A Unit of IDEX Corporation
4799 Dahlia Street
Denver, CO 80216-3070 USA
P: 1-800-525-0758
F: 1-800-624-3925
WWW.CABLEJOINTS.CO.UK
THORNE & DERRICK UK
TEL 0044 191 490 1547 FAX 0044 477 5371
www.BAND-IT-IDEX.com
TEL 0044 117 977 4647 FAX 0044 977 5582
WWW.THORNEANDDERRICK.CO.UK
Page 1 of 2
Document # P15488 Rev. D
© Copyright
BAND-IT-IDEX, Inc. 2007
All rights reserved
Installation
Instructions
Hand Tools
J93099
Cutter Blade Kit
Air Tools
1-3/4” long – S750, S100
2” long – S350
½” long
CAUTION: To prevent breakage,
backing plate must be installed flush
with cutter blade.
INCORRECT
CORRECT
Backing Plate
Hone these
surfaces
Backing
Plate
Cutter Blade
Cutter
Blade
Leading
Edge
Rough edges on
clamp band are
indication of need to
hone cutter blade.
Installation
Instructions
Hand Tools
J93099
Cutter Blade Kit
Air Tools
1-3/4” long – S750, S100
2” long – S350
½” long
CAUTION: To prevent breakage,
backing plate must be installed flush
with cutter blade.
INCORRECT
CORRECT
Backing Plate
Backing
Plate
Leading
Edge
Hone these
surfaces
Cutter
Blade
WWW.CABLEJOINTS.CO.UK
THORNE & DERRICK UK
TEL 0044 191 490 1547 FAX 0044 477 5371
TEL 0044 117 977 4647 FAX 0044 977 5582
WWW.THORNEANDDERRICK.CO.UK
Rough edges on
clamp band are
indication of need to
hone cutter blade.
Cutter Blade
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement